Switching Power Module

Size: px

Start display at page:

Download "Switching Power Module"

Cornelia Sanders
5 years ago
Views:

1 Assembled in U.S.A Rev. A GCU-HOSP 243C ID. COT. EQ. IEC PEV /EC Class (0) HomeWorks DI Power odule Switching Power odule The Switching Power odule family is a group of modular products for the control of lighting loads. This product is compatible with utron HomeWorks systems only. This document describes the following product: E-4S-D: 4-zone power module for switching only. Features Adaptive zero-cross switching maximizes relay life. Activity adapts to variations in relay timing. Rated for lighting loads as defined by IEC/E 60669, EA 40, as well as IC, V, and EV. Includes link for seamless connection to a HomeWorks system. EDs on the module provide diagnostic information. Buttons on module provide load override control. anual Override Contact Closure Input (). Contact Closure Output (). Power failure memory. HomeWorks E-4S-D E-4S-D (shown) IEC SEV / a X, FA / 6 RA System Example HomeWorks Panel seetouch Wallstation Dimming Power odule Contact Closure Interface GRAFIK Eye Contact Closure Output anual Override Contact Closure Input HomeWorks E-4A-D IEC SEV / D D2 D3 D4 Switching Power odule HomeWorks E-4S-D IEC SEV / X, FA / 6 RA ink HomeWorks Processor (HQP6-2) Guestroom Control Unit Up to 99 devices Specification Submittal Page odel umbers:

2 HomeWorks DI Power odule Specifications a Regulatory Approvals IEC/E U isted cu isted O Certified utron Quality Systems registered to ISO Power V~ 50/60 Hz Single input feed 4 A maximum input current ightning strike protection meets ASI/IEEE standard C62.4 and IEC Can withstand voltage surges up to V~ and current surges up to A. ESD-protection exceeds agency requirements per IEC For ungrounded delta feed applications, contact utron. Environment For thermal specifications, see ounting section Relative humidity: less than 90% non-condensing For indoor use only Terminals ains wiring:.0 mm² to 2.5 mm² (8 AWG to 2 AWG) / wiring: 0.5 mm² to 2.5 mm² (22 AWG to 2 AWG) Zone wiring:.0 mm² to 2.5 mm² (8 AWG to 2 AWG) ink: 0.5 mm² to 2.5 mm² (22 AWG to 2 AWG) anual ode Operation Zone button on the unit can be used to turn loads on and off. anual Override Contact Closure Input () When the is open, the Switching Power odule will enter anual Override ode, which will turn on all loads to their override level and disable control of all local zones and devices. When the is closed or jumpered (factory default), the Switching Power odule zones will return to the settings or levels they were at prior to entering anual Override ode. Contact Closure Output () Accepts voltages of 0 24 V~ / 0 24 V-; see chart below for load switching capacities: Switching Voltage Resistive oad R 0 24 V-.0 A 0 24 V~ 0.5 A Provides both normally open (.O.) and normally closed (.C.) dry contacts. aintained or momentary output type. Output relay is non-latching (if relay is closed and power is lost, relay will open). The is not rated to control unclamped, inductive loads. Inductive loads include, but are not limited to, relays, solenoids, and motors. To control these types of equipment, a flyback diode (not included) must be used (DC voltages only). See diagram below. Flyback Diode (required for inductive loads) Inductive oad +.O. Output.C. 24 V- maximum Specification Submittal Page odel umbers:

3 HomeWorks DI Power odule Specifications - (continued) a Programming and Compatibility Requirements E-4S-D can be used with only the HomeWorks system. Setup and programming of the Switching odule is done through the HomeWorks programming software. HomeWorks software version 9.0 or higher required. HomeWorks Wallstations HomeWorks wallstations can be configured to control Switching odules with the HomeWorks programming software. Wallstation ED indicators display the status of programmed lights. ink imits A link in a HomeWorks system can have up to 52 zones (outputs) and 00 devices (required HomeWorks processor counts as device on the link). Each Switching odule counts as one device toward the 00 device limit, and up to 4 zones toward the 52 zone limit. Output Zone Ratings Each zone is rated at for switching. Rated for resistive, inductive, or capacitive lighting loads as defined by IEC/E 60669, EA 40. Air gap off per output o minimum load per output Output should not be used to control general purpose receptacles. Run a separate neutral for each load circuit. A common neutral connection is not recommended. Unit may be powered by Ground Fault Interrupter (GFI) or Residual Current Circuit Breaker with Overload (RCBO) protected circuit if required. For applications requiring higher wattage ratings, use GRX-TVI or E-4S0-D for 230 V~; PHP-SW-DV-B or GRX-TVI for 20 V~. oad Type Tungsten AC General Use Electric Discharge amp Electric Ballast (EA 40) Resistive Inductive otor 2 Relay Ratings V~ When using tungsten loads, lamps should be from a reputable manufacturer and be fused. utron recommends using an IEC compliant 2 A external fuse for each output that is using tungsten loads. Please see Application ote for additional information. 2 Two motors max per module. Specification Submittal Page odel umbers:

4 HomeWorks echanical Dimensions DI Power odule a HomeWorks E-4S-D IEC SEV / X, FA / 6 RA 89.7 mm (3.53 in) 60.6 mm (2.38 in) 6.7 mm (6.37 in) ounting ount in IP20 (minimum) rated consumer panel or breaker panel with integrated DI rail. For United States and Canada, use EA Type minimum rated enclosure. Unit is 9 DI modules (6.7 mm [6.37 in]) wide. ount in an accessible and serviceable location. Unit may be mounted by pressing the unit onto the DI rail with the clips locked. To remove the unit from the DI rail, unlock the clips using a screwdriver. See utron P / at www. for more information on mounting and installation in panels with integrated DI rail. ount the Power odule where audible noise is acceptable (internal relays click). Unit generates heat, maximum 24 BTUs/hr. ount unit such that all the conditions below are met: Room ambient temperature is between 0 ºC and 40 ºC (32 ºF and 04 ºF). Temperature inside mounting panel, within 20 mm (0.80 in) of unit, is between 0 ºC and 40 ºC (32 ºF and 04 ºF). Calibration point maximum: 65 ºC (49 ºF). Prog. Prog. Zn. Zn. Zn. Zn. 2 2 Zn. Zn. 3 3 Zn. Zn. 4 4 HomeWorks E-4S-D V~ V~ / 60 / 60 Hz Hz 4 4 A A IEC IEC SEV SEV / / ECR ECR Class Class 2 2 ounting clips (4) on unit ocked Unlocked V~ V~ A V~ V~ X, AX, FA FA / 6 / 6 RA RA Specification Submittal Page odel umbers:

5 HomeWorks DI Power odule Wiring: ains and Output Zones Wiring from Distribution to Switching Power odule Turn off all circuit breakers or isolators feeding the Switching Power odule at the distribution panel. Run line / hot and neutral wires from a V~ 50 / 60 Hz feed to the Switching Power odule unit. Run a separate neutral for each load circuit. A common neutral connection is not recommended. ains Wiring and IEC PEV / EC Class 2 Separation Follow appropriate local and national codes to avoid violating required separation guidelines a IEC PEV/EC Class 2 ink Zn. 3 Zn. 4 HomeWorks E-4S-D 0 / 60 Hz 4 A IEC SEV / X, FA / 6 RA ains eutral Outputs IEC SEV / X, 20 FA / 6 RA V~ Distribution Panel V~ Hot/ine eutral To additional modules ote: If feeding through utron modules using mains terminals, total current of all modules must be less than or equal to 5 A. Zone Zone 2 Zone 3 Zone 4 Specification Submittal Page odel umbers:

6 HomeWorks DI Power odule Wiring: anual Override Contact Closure Input and Contact Closure Output IEC PEV/EC Class 2 Contact Closures anual Override Contact Closure Input () /Contact Closure Output () wiring is IEC PEV/EC Class 2. Follow all applicable national and local codes for proper circuit separation and protection. Pre-installed Jumper Wiring Prog. Zn. Zn. 2 Zn. 3 Zn. 4 HomeWorks E-4S-D V~ 50 // 60 Hz 4 A OR Device Wiring Turn off all breakers or isolators feeding the Switching Power odule Prog. at Zn. distribution Zn. 2 Zn. Prog. 3 Zn. Zn. 4 Zn. 2 Zn. 3 Prog. Zn. 4 Zn. Zn. 2 Zn. 3 Zn. Zn. 4 IEC SEV / panel before servicing unit. is local control only HomeWorks and cannot control HomeWorks HomeWorks HomeWorks other units over the E-4S-D link. on multiple E-4S-D E-4S-D E-4S-D V~ 50 / Hz V~ A 50 / 60 Hz 4 A units may be connected to an emergency or manual override device in parallel if event is intended to affect multiple units. When in anual Override ode: All zone outputs will be at their programmed light level (default is 00%). Controls will not affect units in anual Override ode. Controls connected to a unit in anual Override ode will continue to affect units on the link that are not in anual Override ode. anual override contact closure input is normally closed (.C.). Prog. The Zn. Switching Zn. 2 Zn. 3 Zn. 4 Power odule is shipped with a jumper pre installed. ote: The Switching Power odule will default to anual HomeWorks Override ode if the is left open. If no anual Override contact E-4S-D input is required, please leave the wire jumper in the terminals..o..o..c..c. Prog. Zn. 2 Zn. 3 Zn. 4 IEC SEV / IEC SEV / / a V~ 50 / Device Hz V~ A Wiring 50 / 60 Hz 4 A (.O.) X, FA 20 / RA V~ X, FA 20 / 6 - RA 240 (.C.) Third-party Device Third-party Device Wiring.O. Wiring OR.C. Wiring V~ V~ X, FA // 6 RA IEC SEV / IEC EC Specification Submittal Page odel umbers:

7 HomeWorks DI Power odule Wiring: ink ink IEC PEV / EC Class 2 Wiring ink communicates using IEC PEV / EC Class 2 wiring. Turn off all breakers or isolators feeding the Switching Power odule at distribution panel before servicing unit. Follow all applicable national and local codes for proper circuit separation and protection. Wiring may be daisy chained or t-tapped. Total length of link wiring must not exceed 60 m (2 000 ft). Wire Gauge: Control (terminals and 2): pair.0 mm 2 (8 AWG). Data (terminals 3 and 4): pair 0.5 mm 2 to.0 mm 2, (22 AWG to 8 AWG) twisted and shielded. Can use utron cable GRX-CB-346S-500. See HomeWorks Wiring Guidelines application note on or resi.utron.com HomeWorks E-4S-D Prog. Zn. Zn. Zn. Zn. 2 2Zn. Zn. 3 3Zn. Zn. 4 4 Control ink : 2: Do ot Connect Data ink 3: 4: HomeWorks E-4S-D V~ / 60 / 60 Hz Hz 44 A A IEC IEC SEV SEV / / ECR ECR Class Class a V~ V~ V~ V~ X, X, FA FA / 6 / RA 6 RA IEC EC Specification Submittal Page odel umbers:

QSNE-4S5-230-D V~ 50 / 60 Hz 16 A. Dimming Power Module CCI. Option Def. Input. H Opt1. Hi Temp Prog Power

QSNE-4S5-230-D V~ 50 / 60 Hz 16 A. Dimming Power Module CCI. Option Def. Input. H Opt1. Hi Temp Prog Power 800 W ax 500 W ax 500 W ax 500 W ax Zone 1 Zone 2 Zone 3 Zone 4 Option Def H Opt1 Opt2 Opt3 230 V~ 50 / 60 Hz 10 A www. H H G G Switching Power odule The DI Power odule (DP) family is a group of modular