MT8814AP. ISO-CMOS 8 x 12 Analog Switch Array. Features. -40 to 85 C. Description. Applications

Size: px
Start display at page:

Download "MT8814AP. ISO-CMOS 8 x 12 Analog Switch Array. Features. -40 to 85 C. Description. Applications"

Transcription

1 MT884 8 x 2 Analog Switch Array Features Internal control latches and address decoder Short set-up and hold times Wide operating voltage: 4.5 to 3.2 2pp analog signal capability R ON 65Ω DD =2, 25 C R ON DD =2, 25 C Full CMOS switch for low distortion Minimum feedthrough and crosstalk Separate analog and digital reference supplies Low power consumption technology Applications Key systems PBX systems Mobile radio Test equipment /instrumentation Analog/digital multiplexers Audio/ideo switching MT884AE MT884AP Description ISSUE 3 March 997 Ordering Information 4 Pin Plastic DIP 44 Pin PLCC -4 to 85 C The Mitel MT884 is fabricated in MITEL s ISO- CMOS technology providing low power dissipation and high reliability. The device contains a 8 x 2 array of crosspoint switches along with a 7 to 96 line decoder and latch circuits. Any one of the 96 switches can be addressed by selecting the appropriate seven address bits. The selected switch can be turned on or off by applying a logical one or zero to the DATA input. SS is the ground reference of the digital inputs. The range of the analog signal is from DD to EE. Chip Select (CS) allows the crosspoint array to be cascaded for matrix expansion. CS STROBE DATA RESET DD EE SS AX AX AX2 AX3 AY AY AY2 7 to 96 Decoder 96 Latches 96 8 x 2 Switch Array Xi I/O (i=-) Yi I/O (i=-7) Figure - Functional Block Diagram 3-33

2 MT884 Y3 AY2 RESET AX3 AX X6 X7 X8 X9 X X Y7 SS Y6 STROBE Y5 SS Pin Description DD Y2 DATA Y CS Y X X X2 X3 X4 X5 AY AY AX2 AX Y4 AX X6 X7 X8 X9 X X Y7 SS 4 PIN PLASTIC DIP 44 PIN PLCC Figure 2 - Pin Connections AX3 RESET AY2 Y3 DD Y2 DATA Y CS Y6 STROBE Y5 EE Y4 AX AX2 AY AY Y X X X2 X3 X4 X5 PDIP Pin # PLCC Name Description Y3 Y3 Analog (Input/Output): this is connected to the Y3 column of the switch 2 2 AY2 Y2 Address Line (Input). 3 3 RESET Master RESET (Input): this is used to turn off all switches regardless of the condition of CS. Active High. 4,5 4,7 AX3,AX X3 and X Address Lines (Inputs). 6,7 5,6,8 No Connection X6-X X6-X Analog (Inputs/Outputs): these are connected to the X6-X rows of the switch 4 5,8 No Connection 5 6 Y7 Y7 Analog (Input/Output): this is connected to the Y7 column of the switch 6 7 SS Digital Ground Reference. 7 9 Y6 Y6 Analog (Input/Output): this is connected to the Y6 column of the switch 8 2 STROBE STROBE (Input): enables function selected by address and data. Address must be stable before STROBE goes high and DATA must be stable on the falling edge of the STROBE. Active High. 9 2 Y5 Y5 Analog (Input/Output): this is connected to the Y5 column of the switch 2 22 EE Negative Power Supply Y4 Y4 Analog (Input/Output): this is connected to the Y4 column of the switch 22, 23 24,25 AX,AX2 X and X2 Address Lines (Inputs). 24, 25 26,27 AY,AY Y and Y Address Lines (Inputs). 26, No Connection X5-X X5-X Analog (Inputs/Outputs): these are connected to the X5-X rows of the switch No Connection Y Y Analog (Input/Output): this is connected to the Y column of the switch 3-34

3 MT884 Pin Description PDIP Pin # PLCC Name Description 36 4 CS Chip Select (Input): this is used to select the device. Active High Y Y Analog (Input/Output): this is connected to the Y column of the switch DATA DATA (Input): a logic high input will turn on the selected switch and a logic low will turn off the selected switch. Active High Y2 Y2 Analog (Input/Output): this is connected to the Y2 column of the switch 4 44 DD Positive Power Supply. Functional Description The MT884 is an analog switch matrix with an array size of 8 x 2. The switch array is arranged such that there are 8 columns by 2 rows. The columns are referred to as the Y inputs/outputs and the rows are the X inputs/outputs. The crosspoint analog switch array will interconnect any X I/O with any Y I/O when turned on and provide a high degree of isolation when turned off. The control memory consists of a 96 bit write only RAM in which the bits are selected by the address inputs (AY-AY2, AX-AX3). Data is presented to the memory on the DATA input. Data is asynchronously written into memory whenever both the CS (Chip Select) and STROBE inputs are high and are latched on the falling edge of STROBE. A logical written into a memory cell turns the corresponding crosspoint switch on and a logical turns the crosspoint off. Only the crosspoint switches corresponding to the addressed memory location are altered when data is written into memory. The remaining switches retain their previous states. Any combination of X and Y inputs/outputs can be interconnected by establishing appropriate patterns in the control memory. A logical on the RESET input will asynchronously return all memory locations to logical turning off all crosspoint switches regardless of whether CS is high or low. Two voltage reference pins ( SS and EE ) are provided for the MT884 to enable switching of negative analog signals. The range for digital signals is from DD to SS while the range for analog signals is from DD to EE. SS and EE pins can be tied together if a single voltage reference is needed. Address Decode The seven address inputs along with the STROBE and CS (Chip Select) are logically ANDed to form an enable signal for the resettable transparent latches. The DATA input is buffered and is used as the input to all latches. To write to a location, RESET must be low and CS must go high while the address and data are set up. Then the STROBE input is set high and then low causing the data to be latched. The data can be changed while STROBE is high, however, the corresponding switch will turn on and off in accordance with the DATA input. DATA must be stable on the falling edge of STROBE in order for correct data to be written to the latch. 3-35

4 MT884 Absolute Maximum Ratings*- oltages are with respect to EE unless otherwise stated. Parameter Symbol Min Max Units Supply oltage DD -.3 SS -.3 * Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied. 6. DD Analog Input oltage INA -.3 DD Digital Input oltage IN SS -.3 DD Current on any I/O Pin I ±5 ma 5 Storage Temperature T S C 6 Package Power Dissipation PLASTIC DIP P D.6 W Recommended Operating Conditions - oltages are with respect to EE unless otherwise stated. Characteristics Sym Min Typ Max Units Test Conditions Operating Temperature T O C 2 Supply oltage DD SS 4.5 EE 3.2 DD Analog Input oltage INA EE DD 4 Digital Input oltage IN SS DD DC Electrical Characteristics - oltages are with respect to EE = SS =, DD =2 unless otherwise stated. Characteristics Sym Min Typ Max Units Test Conditions Quiescent Supply Current I DD µa All digital inputs at IN = SS or DD.4.5 ma All digital inputs at IN =2.4 + SS ; SS = ma All digital inputs at IN =3.4 2 Off-state Leakage Current (See G.9 in Appendix) I OFF ± ±5 na I Xi - Yj I = DD - EE See Appendix, Fig. A. 3 Input Logic level IL.8+ SS SS =7.5; EE = 4 Input Logic level IH 2.+ SS SS =6.5; EE = 5 Input Logic level IH Input Leakage (digital pins) I LEAK. µa All digital inputs at IN = SS or DD DC Electrical Characteristics are over recommended temperature range. Typical figures are at 25 C and are for design aid only; not guaranteed and not subject to production testing. DC Electrical Characteristics- Switch Resistance - DC is the external DC offset applied at the analog I/O pins. Characteristics Sym 25 C 7 C 85 C Units Test Conditions On-state DD =2 Resistance DD = DD = 5 (See G., G.2, G.3 in Appendix) 2 Difference in on-state resistance between two switches (See G.4 in Appendix) R ON Typ Max Typ Max Typ Max Ω Ω Ω SS = EE =, DC = DD /2, I Xi - Yj I =.4 See Appendix, Fig. A.2 R ON 5 Ω DD =2, SS = EE =, DC = DD /2, I Xi - Yj I =.4 See Appendix, Fig. A

5 MT884 AC Electrical Characteristics - Crosspoint Performance-oltages are with respect to DD =5, SS =, EE =-7, unless otherwise stated. Characteristics Sym Min Typ Max Units Test Conditions Switch I/O Capacitance C S 2 pf f= MHz 2 Feedthrough Capacitance C F.2 pf f= MHz 3 Frequency Response Channel ON 2LOG( OUT / Xi )=-3dB 4 Total Harmonic Distortion (See G.5, G.6 in Appendix) 5 Feedthrough Channel OFF Feed.=2LOG ( OUT / Xi ) (See G.8 in Appendix) 6 Crosstalk between any two channels for switches Xi-Yi and Xj-Yj. Xtalk=2LOG ( Yj / Xi ). (See G.7 in Appendix). 7 Propagation delay through switch F 3dB 45 MHz Switch is ON ; INA = 2pp sinewave; R L = kω See Appendix, Fig. A.3 THD. % Switch is ON ; INA = 2pp sinewave f= khz; R L =kω FDT -95 db All Switches OFF ; INA = 2pp sinewave f= khz; R L = kω. See Appendix, Fig. A.4 X talk -45 db INA =2pp sinewave f= MHz; R L = 75Ω. -9 db INA =2pp sinewave f= khz; R L = 6Ω. -85 db INA =2pp sinewave f= khz; R L = kω. -8 db INA =2pp sinewave f= khz; R L = kω. Refer to Appendix, Fig. A.5 for test circuit. t PS 3 ns R L =kω; C L =5pF Timing is over recommended temperature range. See Fig. 3 for control and I/O timing details. Typical figures are at 25 C and are for design aid only; not guaranteed and not subject to production testing. Crosstalk measurements are for Plastic DIPS only, crosstalk values for PLCC packages are approximately 5dB better. AC Electrical Characteristics - Control and I/O Timings- oltages are with respect to DD =5, SS =, EE =-7, unless otherwise stated. Characteristics Sym Min Typ Max Units Test Conditions Control Input crosstalk to switch (for CS, DATA, STROBE, Address) CX talk 3 mpp IN =3 square wave; R IN =kω, R L =kω. See Appendix, Fig. A.6 2 Digital Input Capacitance C DI pf f=mhz 3 Switching Frequency F O 2 MHz 4 Setup Time DATA to STROBE t DS ns R L = kω, C L =5pF ➀ 5 Hold Time DATA to STROBE t DH ns R L = kω, C L =5pF ➀ 6 Setup Time Address to STROBE t AS ns R L = kω, C L =5pF ➀ 7 Hold Time Address to STROBE t AH ns R L = kω, C L =5pF ➀ 8 Setup Time CS to STROBE t CSS ns R L = kω, C L =5pF ➀ 9 Hold Time CS to STROBE t CSH ns R L = kω, C L =5pF ➀ STROBE Pulse Width t SPW 2 ns R L = kω, C L =5pF ➀ RESET Pulse Width t RPW 4 ns R L = kω, C L =5pF ➀ 2 STROBE to Switch Status Delay t S 4 ns R L = kω, C L =5pF ➀ 3 DATA to Switch Status Delay t D 5 ns R L = kω, C L =5pF ➀ 4 RESET to Switch Status Delay t R 35 ns R L = kω, C L =5pF ➀ Timing is over recommended temperature range. See Fig. 3 for control and I/O timing details. Digital Input rise time (tr) and fall time (tf) = 5ns. Typical figures are at 25 C and are for design aid only; not guaranteed and not subject to production testing. ➀ Refer to Appendix, Fig. A.7 for test circuit. 3-37

6 MT884 t CSS t CSH CS 5% 5% t RPW RESET t SPW 5% 5% STROBE 5% 5% 5% t AS ADDRESS 5% 5% t AH DATA 5% 5% t DS t DH SWITCH* ON OFF t D t S t R t R Figure 3 - Control Memory Timing Diagram * See Appendix, Fig. A.7 for switching waveform ➀ AX AX AX2 AX3 AY AY AY2 Connection Table. Address Decode Truth Table This address has no effect on device status. X-Y X-Y X2-Y X3-Y X4-Y X5-Y No Connection No Connection X6-Y X7-Y X8-Y X9-Y X-Y X-Y No Connection ➀ No Connection ➀ X-Y X-Y X-Y2 X-Y2 X-Y3 X-Y3 X-Y4 X-Y4 X-Y5 X-Y5 X-Y6 X-Y6 X-Y7 X-Y7 3-38

MT8812 ISO-CMOS. 8 x 12 Analog Switch Array. Features. Description. Applications

MT8812 ISO-CMOS. 8 x 12 Analog Switch Array. Features. Description. Applications MT882 8 x 2 Analog Switch Array Features Internal control latches and address decoder Short set-up and hold times Wide operating voltage: 4.5V to 4.5V 4Vpp analog signal capability R ON 65 max. @ V DD

More information

MT8806 ISO-CMOS 8x4AnalogSwitchArray

MT8806 ISO-CMOS 8x4AnalogSwitchArray MT886 ISO-CMOS 8x4AnalogSwitchArray Features Internal control latches and address decoder Short set-up and hold times Wide operating voltage: 4.5 V to 3.2 V 2Vpp analog signal capability R ON 65 max. @

More information

MT x 12 Analog Switch Array

MT x 12 Analog Switch Array MT885 8 x 2 Analog Switch Array Features Internal control latches and address decoder Short set-up and hold times Wide operating voltage: 4.5V to 3.2V 2Vpp analog signal capability R ON 65 max. @ V DD

More information

HCF4054B 4 SEGMENT LIQUID CRYSTAL DISPLAY DRIVER WITH STROBED LATCH FUNCTION

HCF4054B 4 SEGMENT LIQUID CRYSTAL DISPLAY DRIVER WITH STROBED LATCH FUNCTION 4 SEGMENT LIQUID CRYSTAL DISPLAY DRIVER WITH STROBED LATCH FUNCTION QUIESCENT CURRENT SPECIF. UP TO 20V OPERATION OF LIQUID CRYSTALS WITH CMOS CIRCUITS PROVIDES ULTRA LOW POWER DISPLAYS EQUIVALENT AC OUTPUT

More information

V6118 EM MICROELECTRONIC - MARIN SA. 2, 4 and 8 Mutiplex LCD Driver

V6118 EM MICROELECTRONIC - MARIN SA. 2, 4 and 8 Mutiplex LCD Driver EM MICROELECTRONIC - MARIN SA 2, 4 and 8 Mutiplex LCD Driver Description The is a universal low multiplex LCD driver. The version 2 drives two ways multiplex (two blackplanes) LCD, the version 4, four

More information

HCF4027B DUAL J-K MASTER SLAVE FLIP-FLOP

HCF4027B DUAL J-K MASTER SLAVE FLIP-FLOP DUAL J-K MASTER SLAVE FLIP-FLOP SET RESET CAPABILITY STATIC FLIP-FLOP OPERATION - RETAINS STATE INDEFINETELY WITH CLOCK LEVEL EITHER HIGH OR LOW MEDIUM-SPEED OPERATION - 16MHz (Typ. clock toggle rate at

More information

HCF40193B PRESETTABLE UP/DOWN COUNTERS (DUAL CLOCK WITH RESET) BINARY TYPE

HCF40193B PRESETTABLE UP/DOWN COUNTERS (DUAL CLOCK WITH RESET) BINARY TYPE PRESETTABLE UP/DOWN COUNTERS (DUAL CLOCK WITH RESET) BINARY TYPE INDIVIDUAL CLOCK LINES FOR COUNTING UP OR COUNTING DOWN SYNCHRONOUS HIGH-SPEED CARRY AND BORROW PROPAGATION DELAYS FOR CASCADING ASYNCHRONOUS

More information

HCC4054B/55B/56B HCF4054B/55B/56B

HCC4054B/55B/56B HCF4054B/55B/56B HCC454B/55B/56B HCF454B/55B/56B LIQUID-CRYSTAL DISPLAY DRIERS 454B 4-SEGMENT DISPLAY DRIER - STROBED LATCH FUNCTION 455B BCD TO 7-SEGMENT DECODER/DRIER, WITH DIS- PLAY-FREQUENCY OUTPUT 456B BCD TO 7-SEGMENT

More information

Obsolete Product(s) - Obsolete Product(s)

Obsolete Product(s) - Obsolete Product(s) OCTAL BUS TRANSCEIVER/REGISTER WITH 3 STATE OUTPUTS HIGH SPEED: f MAX = 60 MHz (TYP.) at V CC = 4.5V LOW POWER DISSIPATION: I CC = 4µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS : V IH = 2V (MIN.)

More information

S6B CH SEGMENT DRIVER FOR DOT MATRIX LCD

S6B CH SEGMENT DRIVER FOR DOT MATRIX LCD 64 CH SEGMENT DRIVER FOR DOT MATRIX LCD June. 2000. Ver. 0.0 Contents in this document are subject to change without notice. No part of this document may be reproduced or transmitted in any form or by

More information

DM Segment Decoder/Driver/Latch with Constant Current Source Outputs

DM Segment Decoder/Driver/Latch with Constant Current Source Outputs 7-Segment Decoder/Driver/Latch with Constant Current Source Outputs General Description The DM9368 is a 7-segment decoder driver incorporating input latches and constant current output circuits to drive

More information

64CH SEGMENT DRIVER FOR DOT MATRIX LCD

64CH SEGMENT DRIVER FOR DOT MATRIX LCD 64CH SEGMENT DRIVER FOR DOT MATRIX LCD INTRODUCTION The (TQFP type: S6B2108) is a LCD driver LSI with 64 channel output for dot matrix liquid crystal graphic display systems. This device consists of the

More information

DESCRIPTION FEATURES APPLICATIONS. LTC7543/LTC8143 Improved Industry Standard Serial 12-Bit Multiplying DACs TYPICAL APPLICATION

DESCRIPTION FEATURES APPLICATIONS. LTC7543/LTC8143 Improved Industry Standard Serial 12-Bit Multiplying DACs TYPICAL APPLICATION Improved Industry Standard Serial -Bit Multiplying DACs FEATRES Improved Direct Replacement for AD754 and DAC-84 Low Cost DNL and INL Over Temperature: ±0.5LSB Easy, Fast and Flexible Serial Interface

More information

82C55A CHMOS PROGRAMMABLE PERIPHERAL INTERFACE

82C55A CHMOS PROGRAMMABLE PERIPHERAL INTERFACE Y Y Y Y Y 82C55A CHMOS PROGRAMMABLE PERIPHERAL INTERFACE Compatible with all Intel and Most Other Microprocessors High Speed Zero Wait State Operation with 8 MHz 8086 88 and 80186 188 24 Programmable I

More information

74F273 Octal D-Type Flip-Flop

74F273 Octal D-Type Flip-Flop Octal D-Type Flip-Flop General Description The 74F273 has eight edge-triggered D-type flip-flops with individual D inputs and Q outputs. The common buffered Clock (CP) and Master Reset (MR) inputs load

More information

DATASHEET HA457. Features. Applications. Ordering Information. Pinouts. 95MHz, Low Power, AV = 2, 8 x 8 Video Crosspoint Switch

DATASHEET HA457. Features. Applications. Ordering Information. Pinouts. 95MHz, Low Power, AV = 2, 8 x 8 Video Crosspoint Switch DATASHEET HA457 95MHz, Low Power, AV = 2, 8 x 8 Video Crosspoint Switch FN4231 Rev 2. The HA457 is an 8 x 8 video crosspoint switch suitable for high performance video systems. Its high level of integration

More information

DM Segment Decoder/Driver/Latch with Constant Current Source Outputs

DM Segment Decoder/Driver/Latch with Constant Current Source Outputs DM9368 7-Segment Decoder/Driver/Latch with Constant Current Source Outputs General Description The DM9368 is a 7-segment decoder driver incorporating input latches and constant current output circuits

More information

64CH SEGMENT DRIVER FOR DOT MATRIX LCD INTRODUCTION FEATURES 100 QFP-1420C

64CH SEGMENT DRIVER FOR DOT MATRIX LCD INTRODUCTION FEATURES 100 QFP-1420C INTRODUCTION The KS0108B is a LCD driver LSl with 64 channel output for dot matrix liquid crystal graphic display systems. This device consists of the display RAM, 64 bit data latch, 64 bit drivers and

More information

NT Output LCD Segment/Common Driver NT7701. Features. General Description. Pin Configuration 1 V1.0

NT Output LCD Segment/Common Driver NT7701. Features. General Description. Pin Configuration 1 V1.0 160 Output LCD Segment/Common Driver Features (Segment mode)! Shift Clock frequency : 14 MHz (Max.) (VDD = 5V ± 10%) 8 MHz (Max.) (VDD = 2.5V - 4.5V)! Adopts a data bus system! 4-bit/8-bit parallel input

More information

Sitronix ST CH Segment Driver for Dot Matrix LCD. !"Dot matrix LCD driver with two 40 channel

Sitronix ST CH Segment Driver for Dot Matrix LCD. !Dot matrix LCD driver with two 40 channel ST Sitronix ST7063 80CH Segment Driver for Dot Matrix LCD Functions Features!"Dot matrix LCD driver with two 40 channel outputs!"bias voltage (V1 ~ V4)!"input/output signals #"Input : Serial display data

More information

NT Output LCD Segment/Common Driver. Features. General Description. Pin Configuration 1 V1.0 NT7702

NT Output LCD Segment/Common Driver. Features. General Description. Pin Configuration 1 V1.0 NT7702 240 Output LCD Segment/Common Driver Features (Segment mode)! Shift Clock frequency: 20 MHz (Ma.) (VDD = 5 V ± 10%)! Adopts a data bus system! 4-bit/8-bit parallel input modes are selectable with a mode

More information

DM74LS377 Octal D-Type Flip-Flop with Common Enable and Clock

DM74LS377 Octal D-Type Flip-Flop with Common Enable and Clock October 1988 Revised March 2000 DM74LS377 Octal D-Type Flip-Flop with Common Enable and Clock General Description The DM74LS377 is an 8-bit register built using advanced low power Schottky technology.

More information

KS0108B 64CH SEGMENT DRIVER FOR DOT MATRIX LCD INTRODUCTION 100 QFP

KS0108B 64CH SEGMENT DRIVER FOR DOT MATRIX LCD INTRODUCTION 100 QFP INTRODUCTION 100 QFP The KS0108B is a LCD driver LSl with 64 channel output for dot matrix liquid crystal graphic display system. This device consists of the display RAM, 64 bit data latch 64 bit drivers

More information

RST RST WATCHDOG TIMER N.C.

RST RST WATCHDOG TIMER N.C. 19-3899; Rev 1; 11/05 Microprocessor Monitor General Description The microprocessor (µp) supervisory circuit provides µp housekeeping and power-supply supervision functions while consuming only 1/10th

More information

74F377 Octal D-Type Flip-Flop with Clock Enable

74F377 Octal D-Type Flip-Flop with Clock Enable 74F377 Octal D-Type Flip-Flop with Clock Enable General Description The 74F377 has eight edge-triggered, D-type flip-flops with individual D inputs and Q outputs. The common buffered Clock (CP) input loads

More information

Maintenance/ Discontinued

Maintenance/ Discontinued A/D, D/C Converters for Image Signal Processing MN6570F, MN6570TF, and MN6570EF Low Power 8-Bit, 3-Channel CMOS D/A Converters for Image Processing Overview The MN6570F, MN6570TF, and MN6570EF are highspeed

More information

DP8212 DP8212M 8-Bit Input Output Port

DP8212 DP8212M 8-Bit Input Output Port DP8212 DP8212M 8-Bit Input Output Port General Description The DP8212 DP8212M is an 8-bit input output port contained in a standard 24-pin dual-in-line package The device which is fabricated using Schottky

More information

NT7108. Neotec Semiconductor Ltd. 新德科技股份有限公司 NT7108 LCD Driver. Copyright: NEOTEC (C)

NT7108. Neotec Semiconductor Ltd. 新德科技股份有限公司 NT7108 LCD Driver. Copyright: NEOTEC (C) Copyright: NEOTEC (C) 2002 http:// All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electric or mechanical,

More information

TEA6425 VIDEO CELLULAR MATRIX

TEA6425 VIDEO CELLULAR MATRIX IDEO CELLULAR MATRIX 6 ideo Inputs - 8 ideo Outputs Internal Selectable YC Adders MHz Bandwidth @ -db Selectable 0./6.dB Gain FOR EACH Output High Impedance Switch for each Output (- state operation) Programmable

More information

MACH130-15/20. Lattice/Vantis. High-Density EE CMOS Programmable Logic

MACH130-15/20. Lattice/Vantis. High-Density EE CMOS Programmable Logic FINAL COM L: -15/20 IND: -18/24 MACH130-15/20 High-Density EE CMOS Programmable Logic Lattice/Vantis DISTINCTIVE CHARACTERISTICS 84 Pins 64 cells 15 ns tpd Commercial 18 ns tpd Industrial 66.6 MHz fcnt

More information

Maintenance/ Discontinued

Maintenance/ Discontinued CCD Delay Line Series MNS NTSC-Compatible CCD Video Signal Delay Element Overview The MNS is a CCD signal delay element for video signal processing applications. It contains such components as a shift

More information

MACH220-10/12/15/20. Lattice Semiconductor. High-Density EE CMOS Programmable Logic DISTINCTIVE CHARACTERISTICS GENERAL DESCRIPTION BLOCK DIAGRAM

MACH220-10/12/15/20. Lattice Semiconductor. High-Density EE CMOS Programmable Logic DISTINCTIVE CHARACTERISTICS GENERAL DESCRIPTION BLOCK DIAGRAM FINAL COM L: -10/12/15/20 IND: -14/18/24 MACH220-10/12/15/20 High-Density EE CMOS Programmable Logic Lattice Semiconductor DISTINCTIVE CHARACTERISTICS 8 Pins 9 10 ns tpd 100 MHz fcnt 5 Inputs with pull-up

More information

Video signal switcher

Video signal switcher ideo signal switcher The BA7606 and BA7606F are switching Is developed for use in video cameras. Each contains three two-channelanalog multiplexers. They feature a large dynamic range, and wide operating

More information

74LVQ374 Low Voltage Octal D-Type Flip-Flop with 3-STATE Outputs

74LVQ374 Low Voltage Octal D-Type Flip-Flop with 3-STATE Outputs 74LVQ374 Low Voltage Octal D-Type Flip-Flop with 3-STATE Outputs General Description The LVQ374 is a high-speed, low-power octal D-type flip-flop featuring separate D-type inputs for each flip-flop and

More information

Component Analog TV Sync Separator

Component Analog TV Sync Separator 19-4103; Rev 1; 12/08 EVALUATION KIT AVAILABLE Component Analog TV Sync Separator General Description The video sync separator extracts sync timing information from standard-definition (SDTV), extendeddefinition

More information

Quadruple, 2:1, Mux Amplifiers for Standard-Definition and VGA Signals

Quadruple, 2:1, Mux Amplifiers for Standard-Definition and VGA Signals 9-4457; Rev ; 2/9 Quadruple, 2:, Mux Amplifiers for General Description The MAX954/MAX9542 are quadruple-channel, 2: video mux amplifiers with input sync tip clamps. These devices select between two video

More information

MUHAMMAD NAEEM LATIF MCS 3 RD SEMESTER KHANEWAL

MUHAMMAD NAEEM LATIF MCS 3 RD SEMESTER KHANEWAL 1. A stage in a shift register consists of (a) a latch (b) a flip-flop (c) a byte of storage (d) from bits of storage 2. To serially shift a byte of data into a shift register, there must be (a) one click

More information

Maintenance/ Discontinued

Maintenance/ Discontinued A/D, D/C Converters for Image Signal Processing MN65531AS Low Power 6-Bit CMOS A/D Converter for Image Processing Overview The MN65531AS is a totally parallel 6-bit CMOS analog-to-digital converter with

More information

DS2176 T1 Receive Buffer

DS2176 T1 Receive Buffer T1 Receive Buffer www.dalsemi.com FEATURES Synchronizes loop timed and system timed T1 data streams Two frame buffer depth; slips occur on frame boundaries Output indicates when slip occurs Buffer may

More information

MAX11503 BUFFER. Σ +6dB BUFFER GND *REMOVE AND SHORT FOR DC-COUPLED OPERATION

MAX11503 BUFFER. Σ +6dB BUFFER GND *REMOVE AND SHORT FOR DC-COUPLED OPERATION 19-4031; Rev 0; 2/08 General Description The is a low-power video amplifier with a Y/C summer and chroma mute. The device accepts an S-video or Y/C input and sums the luma (Y) and chroma (C) signals into

More information

Sitronix ST7921. Features : General Description : 96CH Segment Driver For Dot Matrix LCD

Sitronix ST7921. Features : General Description : 96CH Segment Driver For Dot Matrix LCD ST Sitronix PRELIINARY 96CH Segment Driver For Dot atrix LCD Features :!"Display driving bias : static to 1/5!"Power supply for logic : 2.7V ~ 5.5V!"Power supply for LCD voltage (V 0 ~V SS ) : 3V ~ 8V!"Dot

More information

3-Channel 8-Bit D/A Converter

3-Channel 8-Bit D/A Converter FUJITSU SEMICONDUCTOR DATA SHEET DS04-2316-2E ASSP 3-Channel -Bit D/A Converter MB409 DESCRIPTION The MB409 is an -bit resolution ultra high-speed digital-to-analog converter, designed for video processing

More information

SMPTE-259M/DVB-ASI Scrambler/Controller

SMPTE-259M/DVB-ASI Scrambler/Controller SMPTE-259M/DVB-ASI Scrambler/Controller Features Fully compatible with SMPTE-259M Fully compatible with DVB-ASI Operates from a single +5V supply 44-pin PLCC package Encodes both 8- and 10-bit parallel

More information

Features TEMP. RANGE ( C) ICM7245AIM44Z ICM7245 AIM44Z -25 C to +85 C 44 Ld MQFP Q44.10x10

Features TEMP. RANGE ( C) ICM7245AIM44Z ICM7245 AIM44Z -25 C to +85 C 44 Ld MQFP Q44.10x10 DATASHEET 8-Character, 16-Segment, Microprocessor Compatible, LED Display Decoder Driver FN8587 Rev 0.00 The is an 8-character, alphanumeric display driver and controller which provides all the circuitry

More information

UltraLogic 128-Macrocell Flash CPLD

UltraLogic 128-Macrocell Flash CPLD fax id: 6139 CY7C374i Features UltraLogic 128-Macrocell Flash CPLD Functional Description 128 macrocells in eight logic blocks 64 pins 5 dedicated inputs including 4 clock pins In-System Reprogrammable

More information

V DD V DD V CC V GH- V EE

V DD V DD V CC V GH- V EE N/A 480 x 468 Pixels LCD Color Monitor The is a compact full color TFT LCD module, whose driving board is capable of converting composite video signals to the proper interface of LCD panel and is suitable

More information

INTEGRATED CIRCUITS DATA SHEET. TDA8501 PAL/NTSC encoder. Preliminary specification File under Integrated Circuits, IC02

INTEGRATED CIRCUITS DATA SHEET. TDA8501 PAL/NTSC encoder. Preliminary specification File under Integrated Circuits, IC02 INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC02 April 1993 FEATURES Two input stages: R, G, B and (R Y), (B Y), Y with multiplexing Chrominance processing, highly integrated, includes

More information

OBSOLETE. CMOS 80 MHz Monolithic (18) Color Palette RAM-DACs ADV478/ADV471

OBSOLETE. CMOS 80 MHz Monolithic (18) Color Palette RAM-DACs ADV478/ADV471 a FEATURES Personal System/2* Compatible 80 MHz Pipelined Operation Triple 8-Bit (6-Bit) D/A Converters 256 24(18) Color Palette RAM 15 24(18) Overlay Registers RS-343A/RS-170 Compatible Outputs Sync on

More information

M66004SP/FP M66004SP/FP MITSUBISHI DIGITAL ASSP ASSP 16-DIGIT 5X7-SEGMENT VFD CONTROLLER 16-DIGIT 5 7-SEGMENT VFD CONTROLLER

M66004SP/FP M66004SP/FP MITSUBISHI DIGITAL ASSP ASSP 16-DIGIT 5X7-SEGMENT VFD CONTROLLER 16-DIGIT 5 7-SEGMENT VFD CONTROLLER ASSP M664SP/FP M664SP/FP 6-DIGIT 5X7-SEGMENT FD CONTROLLER 6-DIGIT 5 7-SEGMENT FD CONTROLLER DESCRIPTION The M664 is a 6-digit 5 7-segment vacuum fluorescent display (FD) controller using the silicon gate

More information

SDA 3302 Family. GHz PLL with I 2 C Bus and Four Chip Addresses

SDA 3302 Family. GHz PLL with I 2 C Bus and Four Chip Addresses GHz PLL with I 2 C Bus and Four Chip Addresses Preliminary Data Features 1-chip system for MPU control (I 2 C bus) 4 programmable chip addresses Short pull-in time for quick channel switch-over and optimized

More information

1 Watt, MHz, SMT Tunable Band Pass Filter (MINI-ERF ) 1.75 x 2.40 x 0.387

1 Watt, MHz, SMT Tunable Band Pass Filter (MINI-ERF ) 1.75 x 2.40 x 0.387 MN-3-52-X-S4 1 Watt, 3 52 MHz, SMT Tunable Band Pass Filter (MINI-ERF ) 1.75 x 2.4 x.387 Typical Applications Military Radios Military Radar SATCOM Test and Measurement Equipment Industrial and Medical

More information

UNISONIC TECHNOLOGIES CO., LTD 89CXX/89NXX Preliminary CMOS IC

UNISONIC TECHNOLOGIES CO., LTD 89CXX/89NXX Preliminary CMOS IC UNISONIC TECHNOLOGIES CO., LTD 89CXX/89NXX Preliminary CMOS IC LOW OLTAGE FREE DELAY TIME SETTING OLTAGE DETECTOR IC SERIES DESCRIPTION UTC 89CXX and 89NXX series are adjustable output delay oltage Detector

More information

INTEGRATED CIRCUITS DATA SHEET. TDA4510 PAL decoder. Product specification File under Integrated Circuits, IC02

INTEGRATED CIRCUITS DATA SHEET. TDA4510 PAL decoder. Product specification File under Integrated Circuits, IC02 INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC02 March 1986 GENERAL DESCRIPTION The is a colour decoder for the PAL standard, which is pin sequent compatible with multistandard decoder

More information

ASNT_PRBS20B_1 18Gbps PRBS7/15 Generator Featuring Jitter Insertion, Selectable Sync, and Output Amplitude Control

ASNT_PRBS20B_1 18Gbps PRBS7/15 Generator Featuring Jitter Insertion, Selectable Sync, and Output Amplitude Control ASNT_PRBS20B_1 18Gbps PRBS7/15 Generator Featuring Jitter Insertion, Selectable Sync, and Output Amplitude Control Broadband frequency range from 20Mbps 18.0Gbps Minimal insertion jitter Fast rise and

More information

PALCE26V12 Family. 28-Pin EE CMOS Versatile PAL Device DISTINCTIVE CHARACTERISTICS GENERAL DESCRIPTION FINAL COM L: H-7/10/15/20 IND: H-10/15/20

PALCE26V12 Family. 28-Pin EE CMOS Versatile PAL Device DISTINCTIVE CHARACTERISTICS GENERAL DESCRIPTION FINAL COM L: H-7/10/15/20 IND: H-10/15/20 FINAL COM L: H-7//5/2 IND: H-/5/2 PALCE26V2 Family 28-Pin EE CMOS Versatile PAL Device DISTINCTIVE CHACTERISTICS 28-pin versatile PAL programmable logic device architecture Electrically erasable CMOS technology

More information

Maintenance/ Discontinued

Maintenance/ Discontinued A/D, D/C Converters for Image Signal Processing MN657011H Low Power 8-Bit, 3-Channel CMOS D/A Converter for Image Processing Overview The MN657011H is an 8-bit, 3-channel CMOS digitalto-analog converter

More information

12-Bit Serial Daisy-Chain CMOS D/A Converter DAC8143

12-Bit Serial Daisy-Chain CMOS D/A Converter DAC8143 a FEATURES Fast, Flexible, Microprocessor Interfacing in Serially Controlled Systems Buffered Digital Output Pin for Daisy-Chaining Multiple DACs Minimizes Address-Decoding in Multiple DAC Systems Three-Wire

More information

Sitronix ST7921. !"Features : !"General Description : 96CH Segment Driver For Dot Matrix LCD

Sitronix ST7921. !Features : !General Description : 96CH Segment Driver For Dot Matrix LCD ST Sitronix PRELIINARY ST7921 96CH Segment Driver For Dot atrix LCD!"Features : #"Display driving bias : static to 1/5 #"Power supply for logic : 2.7V ~ 5.5V #"Power supply for LCD voltage (V 0 ~V SS )

More information

ZLNB101 DUAL POLARISATION SWITCH TWIN LNB MULTIPLEX CONTROLLER ISSUE 1- JANUARY 2001 DEVICE DESCRIPTION FEATURES APPLICATIONS

ZLNB101 DUAL POLARISATION SWITCH TWIN LNB MULTIPLEX CONTROLLER ISSUE 1- JANUARY 2001 DEVICE DESCRIPTION FEATURES APPLICATIONS DUAL POLARISATION SWITCH TWIN LNB MULTIPLEX CONTROLLER ISSUE - JANUARY 00 ZLNB0 DEICE DESCRIPTION The ZLNB0 dual polarisation switch controller is one of a wide range of satellite receiver LNB support

More information

Octal 3-State Bus Transceivers and D Flip-Flops High-Performance Silicon-Gate CMOS

Octal 3-State Bus Transceivers and D Flip-Flops High-Performance Silicon-Gate CMOS TECNICA DATA IN74C652A Octal 3-State Bus Traceivers and D Flip-Flops igh-performance Silicon-Gate CMOS The IN74C652A is identical in pinout to the S/AS652. The device inputs are compatible with standard

More information

USE GAL DEVICES FOR NEW DESIGNS

USE GAL DEVICES FOR NEW DESIGNS USE GAL DEVICES FOR NEW DESIGNS FINAL COM L: H-7//5/2 IND: H-/5/2 PALCE26V2 Family 28-Pin EE CMOS Versatile PAL Device DISTINCTIVE CHACTERISTICS 28-pin versatile PAL programmable logic device architecture

More information

FUNCTIONAL BLOCK DIAGRAM DELAYED C-SYNC CLOCK AT 8FSC. 5MHz 4-POLE LP PRE-FILTER DC RESTORE AND C-SYNC INSERTION. 5MHz 2-POLE LP POST- FILTER

FUNCTIONAL BLOCK DIAGRAM DELAYED C-SYNC CLOCK AT 8FSC. 5MHz 4-POLE LP PRE-FILTER DC RESTORE AND C-SYNC INSERTION. 5MHz 2-POLE LP POST- FILTER a FEATURES Composite Video Output Chrominance and Luminance (S-Video) Outputs No External Filters or Delay Lines Required Drives 75 Ω Reverse-Terminated Loads Compact 28-Pin PLCC Logic Selectable NTSC

More information

4-BIT PARALLEL-TO-SERIAL CONVERTER

4-BIT PARALLEL-TO-SERIAL CONVERTER 4-BIT PARALLEL-TO-SERIAL CONVERTER FEATURES DESCRIPTION On-chip clock 4 and 8 Extended 00E VEE range of 4.2V to 5.5V.6Gb/s typical data rate capability Differential clock and serial inputs VBB output for

More information

UltraLogic 128-Macrocell ISR CPLD

UltraLogic 128-Macrocell ISR CPLD 256 PRELIMINARY Features 128 macrocells in eight logic blocks In-System Reprogrammable (ISR ) JTAG-compliant on-board programming Design changes don t cause pinout changes Design changes don t cause timing

More information

SC75823E/W. Silan Semiconductors 1/3 DUTY GENERAL-PURPOSE LCD DRIVER HANGZHOU SILAN MICROELECTRONICS CO.,LTD DESCRIPTION FEATURES ORDERING INFORMATION

SC75823E/W. Silan Semiconductors 1/3 DUTY GENERAL-PURPOSE LCD DRIVER HANGZHOU SILAN MICROELECTRONICS CO.,LTD DESCRIPTION FEATURES ORDERING INFORMATION 1/3 DUTY GENERAL-PURPOSE LCD DRIVER DESCRIPTION The is a general-purpose LCD driver that can be used for frequency display in microprocessor-controlled radio receives and in other display applications.

More information

CDK3402/CDK bit, 100/150MSPS, Triple Video DACs

CDK3402/CDK bit, 100/150MSPS, Triple Video DACs CDK3402/CDK3403 8-bit, 100/150MSPS, Triple Video DACs FEATURES n 8-bit resolution n 150 megapixels per second n ±0.2% linearity error n Sync and blank controls n 1.0V pp video into 37.5Ω or load n Internal

More information

PEEL 18CV8-5/-7/-10/-15/-25 CMOS Programmable Electrically Erasable Logic Device

PEEL 18CV8-5/-7/-10/-15/-25 CMOS Programmable Electrically Erasable Logic Device PEEL 18V8-5/-7/-10/-15/-25 MOS Programmable Electrically Erasable Logic Device Multiple Speed, Power, Temperature Options Speeds ranging from 5ns to 25ns Power as low as 37mA at 25MHz ommercial and ndustrial

More information

EL4583. Features. Sync Separator, 50% Slice, S-H, Filter, H OUT. Applications. Ordering Information. Pinout FN Data Sheet March 28, 2013

EL4583. Features. Sync Separator, 50% Slice, S-H, Filter, H OUT. Applications. Ordering Information. Pinout FN Data Sheet March 28, 2013 Data Sheet FN7173.4 Sync Separator, 50% Slice, S-H, Filter, H OUT The EL4583 extracts timing from video sync in NTSC, PAL, and SECAM systems, and non standard formats, or from computer graphics operating

More information

DM Segment Decoder Driver Latch with Constant Current Source Outputs

DM Segment Decoder Driver Latch with Constant Current Source Outputs DM9368 7-Segment Decoder Driver Latch with Constant Current Source Outputs General Description The DM9368 is a 7-segment decoder driver incorporating input latches and constant current output circuits

More information

Product Specification PE4151

Product Specification PE4151 PE UltraCMOS Low Frequency Passive Mixer with Integrated LO Amplifier Product Description The PE is an ultra-high linearity Quad MOSFET mixer with an integrated LO amplifier. The LO amplifier allows for

More information

TIL311 HEXADECIMAL DISPLAY WITH LOGIC

TIL311 HEXADECIMAL DISPLAY WITH LOGIC TIL311 Internal TTL MSI IC with Latch, Decoder, and Driver 0.300-Inch (7,62-mm) Character Height Wide Viewing Angle High Brightness Left-and-Right-Hand Decimals Constant-Current Drive for Hexadecimal Characters

More information

SA9504 Dual-band, PCS(CDMA)/AMPS LNA and downconverter mixers

SA9504 Dual-band, PCS(CDMA)/AMPS LNA and downconverter mixers INTEGRATED CIRCUITS Supersedes data of 1999 Aug 4 1999 Oct 8 DESCRIPTION The is an integrated receiver front-end for 900 MHz Cellular (AMPS) and 1.9 GHz PCS (CDMA) phones. This dual-band receiver circuit

More information

Chapter 7 Sequential Circuits

Chapter 7 Sequential Circuits Chapter 7 Sequential Circuits Jin-Fu Li Advanced Reliable Systems (ARES) Lab. epartment of Electrical Engineering National Central University Jungli, Taiwan Outline Latches & Registers Sequencing Timing

More information

HT9B92 RAM Mapping 36 4 LCD Driver

HT9B92 RAM Mapping 36 4 LCD Driver RAM Mapping 36 4 LCD Driver Feature Logic Operating Voltage: 2.4V~5.5V Integrated oscillator circuitry Bias: 1/2 or 1/3; Duty: 1/4 Internal LCD bias generation with voltage-follower buffers External pin

More information

Maintenance/ Discontinued

Maintenance/ Discontinued CCD Delay Line Series MN390S NTSC-Compatible CCD H Video Signal Delay Element Overview The MN390S is a H image delay element of a f SC CMOS CCD and suitable for video signal processing applications. It

More information

Product Specification PE613050

Product Specification PE613050 PE63050 Product Description The PE63050 is an SP4T tuning control switch based on Peregrine s UltraCMOS technology. This highly versatile switch supports a wide variety of tuning circuit topologies with

More information

CXA1645P/M. RGB Encoder

CXA1645P/M. RGB Encoder MATRIX CXA1645P/M RGB Encoder Description The CXA1645P/M is an encoder IC that converts analog RGB signals to a composite video signal. This IC has various pulse generators necessary for encoding. Composite

More information

LCD display module. graphic 61x16 dots

LCD display module. graphic 61x16 dots MT 6116B LCD display module graphic 61x16 dots General description МТ-6116B LCD display module is composed of LSI controller and LCD panel. The display module appearance is shown in Fig. 1. КB145VG4 controller

More information

3.3V CMOS DUAL J-K FLIP-FLOP WITH SET AND RESET, POSITIVE-EDGE TRIG- GER, AND 5 VOLT TOLERANT I/O DESCRIPTION:

3.3V CMOS DUAL J-K FLIP-FLOP WITH SET AND RESET, POSITIVE-EDGE TRIG- GER, AND 5 VOLT TOLERANT I/O DESCRIPTION: IDT7LV109A.V MOS DUAL J-K FLIP-FLOP WITH SET AND RESET EXTENDED OMMERIAL TEMPERATURE RANGE.V MOS DUAL J-K FLIP-FLOP WITH SET AND RESET, POSITIVE-EDGE TRIG- GER, AND T TOLERANT I/O IDT7LV109A FEATURES:

More information

Is Now Part of To learn more about ON Semiconductor, please visit our website at

Is Now Part of To learn more about ON Semiconductor, please visit our website at Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC

More information

Product Specification PE613010

Product Specification PE613010 Product Description The is an SPST tuning control switch based on Peregrine s UltraCMOS technology. This highly versatile switch supports a wide variety of tuning circuit topologies with emphasis on impedance

More information

No need for external driver, saving PCB space and cost.

No need for external driver, saving PCB space and cost. 50Ω 5 to 2700 MHz High Power 3W The Big Deal High Port count in super small size Single Positive Supply Voltage, 2.5 4.8V High Power P0.1dB, 3W typ. Low Insertion Loss, 0.6 db at 1 GHz CASE STYLE: MT1817

More information

L9822E OCTAL SERIAL SOLENOID DRIVER

L9822E OCTAL SERIAL SOLENOID DRIVER L9822E OCTAL SERIAL SOLENOID DRIVER EIGHT LOW RDSon DMOS OUTPUTS (0.5Ω AT IO = 1A @ 25 C VCC = 5V± 5%) 8 BIT SERIAL INPUT DATA (SPI) 8 BIT SERIAL DIAGNOSTIC OUTPUT FOR OVERLOAD AND OPEN CIRCUIT CONDITIONS

More information

LCD MODULE DEM B SYH

LCD MODULE DEM B SYH DISPLAY Elektronik GmbH LCD MODULE DEM 128064B SYH Product specification Version:0 09/Okt/2006 GENERAL SPECIFICATION MODULE NO. : DEM 128064B SYH CUSTOMER P/N VERSION NO. CHANGE DESCRIPTION DATE 0 ORIGINAL

More information

Distributed by: www.jameco.com --3-4242 The content and copyrights of the attached material are the property of its owner. E2O2-27-X3 Semiconductor MSM2C55A-2RS/GS/VJS This version: Jan. 99 Previous version:

More information

Obsolete Product(s) - Obsolete Product(s)

Obsolete Product(s) - Obsolete Product(s) L4902A DUAL 5 REGULATOR WITH RESET AND DISABLE DOUBLE BATTERY OPERATING OUTPUT CURRENTS : I01 = 300 ma I02 = 300 ma FIXED PRECISION OUTPUT OLTAGE 5 ± 2 % RESET FUNCTION CONTROLLED BY INPUT OLTAGE AND OUTPUT

More information

SP6T RF Switch JSW6-23DR Ω High Power 3W 5 to 2000 MHz. The Big Deal

SP6T RF Switch JSW6-23DR Ω High Power 3W 5 to 2000 MHz. The Big Deal 75Ω High Power 3W 5 to 2000 MHz The Big Deal High Port count in super small size High Power P0.1dB, 3W Low Insertion Loss, 0.7 db at 1 GHz CASE STYLE: MT1817 Product Overview is a high power reflective

More information

LM16X21A Dot Matrix LCD Unit

LM16X21A Dot Matrix LCD Unit LCD Data Sheet FEATURES STC (Super Twisted igh Contrast) Yellow Green Transmissive Type Low Power Consumption Thin, Lightweight Design Permits Easy Installation in a Variety of Equipment General Purpose

More information

Complete 12-Bit 40 MHz CCD Signal Processor AD9945

Complete 12-Bit 40 MHz CCD Signal Processor AD9945 Complete 12-Bit 40 MHz CCD Signal Processor AD9945 FEATURES 40 MSPS Correlated Double Sampler (CDS) 6 db to 40 db 10-Bit Variable Gain Amplifier (VGA) Low Noise Optical Black Clamp Circuit Preblanking

More information

Obsolete Product(s) - Obsolete Product(s)

Obsolete Product(s) - Obsolete Product(s) L4937N DUAL MULTIFUNCTION OLTAGE REGULATOR STANDBY OUTPUT OLTAGE PRECISION 5 ± 2% OUTPUT 2 TRACKED TO THE STANDBY OUT- PUT OUTPUT 2 DISABLE FUNCTION FOR STANDBY MODE ERY LOW QUIESCENT CURRENT, LESS THAN

More information

ICM7218A COMMON ANODE ICM7218C COMMON ANODE ICM7218B COMMON CATHODE ICM7218D COMMON CATHODE ID0-ID7 ID4-ID7 MODE WRITE ID0-ID3 INPUT

ICM7218A COMMON ANODE ICM7218C COMMON ANODE ICM7218B COMMON CATHODE ICM7218D COMMON CATHODE ID0-ID7 ID4-ID7 MODE WRITE ID0-ID3 INPUT DATASHEET ICM2 -Digit LED Microprocessor-Compatible Multiplexed Display Decoder Driver FN359 Rev 4.00 May, 206 The ICM2 series of universal LED driver systems provide, in a single package, all the circuitry

More information

Displays. AND-TFT-7PA-WV 1440 x 234 Pixels LCD Color Monitor. Features

Displays. AND-TFT-7PA-WV 1440 x 234 Pixels LCD Color Monitor. Features 1440 x 234 Pixels LCD Color Monitor The is a compact full color TFT LCD module, whose driving board is capable of converting composite video signals to the proper interface of LCD panel and is suitable

More information

Report on 4-bit Counter design Report- 1, 2. Report on D- Flipflop. Course project for ECE533

Report on 4-bit Counter design Report- 1, 2. Report on D- Flipflop. Course project for ECE533 Report on 4-bit Counter design Report- 1, 2. Report on D- Flipflop Course project for ECE533 I. Objective: REPORT-I The objective of this project is to design a 4-bit counter and implement it into a chip

More information

EM6126 EM MICROELECTRONIC - MARIN SA. Digitally programmable 65 and 81 multiplex rate LCD Controller and Driver. Features. Typical Applications

EM6126 EM MICROELECTRONIC - MARIN SA. Digitally programmable 65 and 81 multiplex rate LCD Controller and Driver. Features. Typical Applications EM MICROELECTRONIC - MARIN SA EM616 Digitally programmable 65 and 81 multiplex rate LCD Controller and Driver Features Slim IC for COG, COF and COB technologies I C & Serial bus interface Internal display

More information

LY62L K X 16 BIT LOW POWER CMOS SRAM

LY62L K X 16 BIT LOW POWER CMOS SRAM REVISION ISTORY Revision Description Issue Date Rev. 1.0 Initial Issue Jul.25.2004 Rev. 2.0 Revised ISB(max) : 0.5mA => 1.25mA May.11.2006 Rev. 2.1 Revised Package Outline Dimension(TSOP-II) Apr.12.2007

More information

Project 6: Latches and flip-flops

Project 6: Latches and flip-flops Project 6: Latches and flip-flops Yuan Ze University epartment of Computer Engineering and Science Copyright by Rung-Bin Lin, 1999 All rights reserved ate out: 06/5/2003 ate due: 06/25/2003 Purpose: This

More information

Power Amplifier 0.5 W 2.4 GHz AM TR Features. Functional Schematic. Description. Pin Configuration 1. Ordering Information

Power Amplifier 0.5 W 2.4 GHz AM TR Features. Functional Schematic. Description. Pin Configuration 1. Ordering Information Features Ideal for 802.11b ISM Applications Single Positive Supply Output Power 27.5 dbm 57% Typical Power Added Efficiency Downset MSOP-8 Package Description M/A-COM s is a 0.5 W, GaAs MMIC, power amplifier

More information

74F574 Octal D-Type Flip-Flop with 3-STATE Outputs

74F574 Octal D-Type Flip-Flop with 3-STATE Outputs 74F574 Octal D-Type Flip-Flop with 3-STATE Outputs General Description The F574 is a high-speed, low power octal flip-flop with a buffered common Clock (CP) and a buffered common Output Enable (OE). The

More information

DATASHEET EL4583. Features. Applications. Ordering Information. Pinout. Sync Separator, 50% Slice, S-H, Filter, HOUT. FN7173 Rev 4.

DATASHEET EL4583. Features. Applications. Ordering Information. Pinout. Sync Separator, 50% Slice, S-H, Filter, HOUT. FN7173 Rev 4. DATASHEET EL4583 Sync Separator, 50% Slice, S-H, Filter, HOUT The EL4583 extracts timing from video sync in NTSC, PAL, and SECAM systems, and non standard formats, or from computer graphics operating at

More information

. The vertical pull-in range is approximately 10 Hz at fv = 60 Hz.

. The vertical pull-in range is approximately 10 Hz at fv = 60 Hz. Ordering number: EN2781B Monolithic Linear IC CRT Display Synchronization Deflection Circuit Overview The is a sync-deflection circuit IC dedicated to CRT display use. It can be connected to the LA7832/7833,

More information