. Record of Revision Date Revision No Summary Rev 1.0 was issued Update LED life time Page 2 of 21

Transcription

1 DLC Display Co., Limited 德爾西顯示器有限公司 MODEL No: DLC1210EIG TEL: FAX: WEB:

2 . Record of Revision Date Revision No Summary Rev 1.0 was issued Update LED life time Page 2 of 21

3 1. Scope This data sheet is to introduce the specification of DLC1210EIG active matrix TFT module. It is composed of a color TFTLCD panel, driver ICs, FPC and a backlight unit. The 12.1 display area contains 1024(RGB) x 768 pixels. 2. Application Digital equipments which need color display, MID, mobile navigator/video systems. 3. General Information Item Contents Unit Size 12.1 inch Resolution 1024(RGB) x 768 / Interface LDS / Technology type asi TFT / Pixel pitch 0.240x0.240 mm Pixel Configuration RGB ertical stripe Outline Dimension (W x H x D) 260.5x204.0x8.4 mm Active Area x mm Display Mode Transmissive; Normally white / Backlight Type LED / Weight 510 g Page 3 of 21

4 4. Outline Drawing Page 4 of 21

5 5. Interface signals TFT LCD MODULE No Symbol 1 RX3+ Differential Data Input, CH3 ( Positive ) 2 RX3 Differential Data Input, CH3 (Negative ) 3 NC 4 SEL68 LDS 6/8 bit select function control, Low or NC 6 bit Input Mode High 8bit Input Mode 5 GND Ground 6 RXC+ Differential Clock Input ( Positive ) 7 RXC Differential Clock Input ( Negative ) 8 GND Ground 9 RX2+ Differential Data Input, CH2 ( Positive ) 10 RX2 Differential Data Input, CH2 ( Negative ) 11 GND Description NC RX1+ Differential Data Input, CH1 ( Positive ) 13 RX1 Differential Data Input, CH1 ( Negative ) GND Ground 15 RX0+ Differential Data Input, CH0 ( Positive ) 16 RX0 Differential Data Input, CH0 (Negative ) relr reud CC CC Note (3) Ground Remarks Horizontal Reverse Scan Control, Low or NC Normal Mode. High Horizontal Reverse Scan ertical Reverse Scan Control, Low or NC Normal Mode, High ertical Reverse Scan Note (3) Note (3) Power Power Note (1) Connector Part No.: STARCONN 076B200048RAG4 or JAE FISEB20PHFE or equivalent. Note (2) User s connector Part No.: JAE FISE20ME or equivalent. Note (3) Low stands for 0. High stands for 3.3. NC stands for No Connected. Page 5 of 21

6 BACKLIGHT UNIT(Converter connector pin) No Symbol Description Remarks 1 i Converter input voltage 12 2 i Converter input voltage 12 3 i Converter input voltage 12 4 i Converter input voltage 12 5 GND Converter ground Ground 6 GND Converter ground Ground 7 GND Converter ground Ground 8 GND Converter ground Ground 9 EN Enable pin ADJ Backlight Adjust PWM Dimming (19020KHz, Hi: 3.3DC,Lo: 0DC) Note (1) Connector Part No.: H01 (ACES) or equivalent. Note (2) User s connector Part No.: (ACES) or equivalent Page 6 of 21

7 Color Data Input Assignment The brightness of each primary color (red, green and blue) is based on the 6bit gray scale data input for the color. The higher the binary input, the brighter the color. The table below provides the assignment of color versus data input. Note (1) 0: Low Level oltage, 1: High Level oltage Page 7 of 21

8 The brightness of each primary color (red, green and blue) is based on the 8bit gray scale data input for the color. The higher the binary input, the brighter the color. The table below provides the assignment of color versus data input. Note (1) 0: Low Level oltage, 1: High Level oltage Page 8 of 21

9 6. Absolute maximum Ratings 6.1.Electrical Absolute max. ratings Parameter Symbol MIN MAX Unit Logic Supply oltage DD Item Symbol MIN MAX Unit Operating Temperature TOPR Storage Temperature TSTG Remark 6.2. Environment Conditions Remark 6.3 Backlight Unit Item Symbol MIN MAX Unit Remark Converter voltage i Note1,2 Enable voltage EN 5.5 Backlight adjust ADJ 5.5 Note (1) Permanent damage to the device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal Operating Conditions. Note (2) Specified values are for lamp (Refer to 5.2 for further information). Page 9 of 21

10 7. Electrical Specifications 7.1 Electrical characteristics GND=0, Ta=25 Item Symbol Power Supply oltage Rush current Power supply current MIN TYP MAX Unit Remark (1) at cc= (1) at cc=5.0 4 A (2) ma (3)a, at vcc= ma (3)a, at vcc= ma (3)a, at vcc= ma (3)a, at vcc=5.0 cc IRUSH White Black Power Consumption PL 2.0 W LDS differential input voltage ID m LDS common input voltage ICM Note (1) The assembly should be always operated within above ranges. Note (2) Measurement Conditions: Page 10 of 21

11 cc rising time is 470μs Note (3) The specified power supply current is under the conditions at cc = 3.3 or 5, Ta = 25 ± 2 ºC, fv= 60 Hz, whereas a power dissipation check pattern below is displayed. a. White Pattern b. Black Pattern 7.2 LED Backlight Ta=25 Item Symbol MIN TYP MAX Unit Converter Power Supply oltage i Converter Power Supply Current Ii A (1) i = 12 (Duty 100%) LED Power Consumption PLED 10 W (1)i = 12 (Duty 100%) EN Control Level Backlight on PWM Control Level PWM high level Backlight off PWM low level Remark PWM Control Duty Ratio % PWM Control Frequency fpwm K Hz (2) LED Life Time Hrs (3) Page 11 of 21

12 Note (1) LED current is measured by utilizing a high frequency current meter as shown below: Note (2) At 20k Hz PWM control frequency duty ratio range is restricted from 20% to 100% Note (3) The lifetime of LED is defined as the time when it continues to operate under the conditions at Ta = 25 ±2 and Duty 100% until the brightness becomes 50% of its original value. 7.3 BLOCK DIAGRAM Page 12 of 21

13 8. Timing Chart 8.1 INPUT SIGNAL TIMING SPECIFICATIONS The input signal timing specifications are shown as the following table and timing diagram. Signal DCLK Horizontal Active Display Term ertical Active Display Term Item Symbol Min Typ Max Unit Note Frequency Fc Display Thd 1024 Tc Blank Thb Tc Total Th Tc Display Tvd 768 Th Blank Tvb Th Total Tv Th Th=Thd+Thb Tv=Tvd+Tvb Note (1) Since this assembly is operated in DE only mode, Hsync and sync input signals should be set to low logic level. Otherwise, this assembly would operate abnormally. (2) Frame rate is 60Hz. INPUT SIGNAL TIMING DIAGRAM Page 13 of 21

14 8.2 POWER ON/OFF SEQUENCE To prevent a latchup or DC operation of LCD assembly, the power on/off sequence should be as the diagram below. Power ON/OFF sequence Note (1) Please avoid floating state of interface signal at invalid period. Note (2) When the interface signal is invalid, be sure to pull down the power supply of LCD CC to 0. Note (3) The Backlight converter power must be turned on after the power supply for the logic and the interface signal is valid. The Backlight converter power must be turned off before the power supply for the logic and the interface signal is invalid. Parameter alue MIN TYP MAX Unit T ms T ms T ms T4 500 ms T5 200 ms T6 200 ms T ms Page 14 of 21

15 8.3 The input data format Page 15 of 21

16 8.4 Scanning Direction The following figures show the image see from the front view. The arrow indicates the direction of scan. Fig. 1 Normal scan ( pin 17, relr = Low or NC, pin 18, reud = Low or NC ) Fig. 2 Reverse scan ( pin 17, relr = High, pin 18, reud = Low or NC ) Fig. 3 Reverse scan ( pin 17, relr = Low or NC, pin 18, reud = High ) Fig. 4 Reverse scan ( pin 17, relr = High, pin 18, reud = High ) Page 16 of 21

17 9. Optical Specification Ta=25 Item Symbol Condition Min Typ. Max. CR θ= ΘT ΘB Contrast Ratio Tr Response Time Tf iew Angles ΘL θr White Red Chromaticity Green Blue Luminance 25 CR 10 x y x y x Brightness Typ 0.05 is on y x y L Unit Note1 Note2 ms Note1 Note3 Degree Note 4 Note5, Note1 Typ Remark cd/m2 Note1 Note6 Note 1: Definition of optical measurement system. Temperature = 25 (±3 ) LED backlight: ON, Environment brightness < 150 lx Page 17 of 21

18 Note 2: Contrast ratio is defined as follow: Contrast Ratio = Surface Luminance with all white pixels Surface Luminance with all black pixels Note 3: Response time is defined as follow: Response time is the time required for the display to transition from black to white (Rise Time, Tr) and from white to black(decay Time, Tf). Note 4: iewing angle range is defined as follow: iewing angle is measured at the center point of the LCD. Page 18 of 21

19 Note 5: Color chromaticity is defined as follow: (CIE1931) Color coordinates measured at center point of LCD. S area of RGB triangle 100% area of NTSC triangle Note 6: Luminance is defined as follow: Luminance is defined as the brightness of all pixels White at the center of display area on optimum contrast. Page 19 of 21

20 10. Environmental / Reliability Tests No Test Item Condition Judgment criteria 1 High Temp Operation Ts=+80, 120hrs Per table in below 2 Low Temp Operation Ta=30, 120hrs Per table in below 3 High Temp Storage Ta=+85, 120hrs Per table in below 4 Low Temp Storage Ta=40, 120hrs Per table in below 5 High Temp & High Ta=+60, 90% RH Humidity Storage 120 hours Per table in below (polarizer discoloration is excluded) 6 Thermal Shock min~ min, (Nonoperation) Change time:5min, 10 Cycles Per table in below 7 8 ESD (Operation) C=150pF, R=330Ω 5points/panel Per table in below Air:±8K, 5times; Contact:±4K, 5 times; ibration (Nonoperation) Frequency range:10~55hz, Stroke:1.5mm Per table in below Sweep:10Hz~55Hz~10Hz 2 hours for each direction of X.Y.Z. Shock (Nonoperation) Package 10 Drop Test 9 INSPECTION Appearance Alignment of LCD Panel Electrical current Function / Display 60G 6ms, ±X,±Y,±Z 3times, for each direction Height:80 cm, 1 corner, 3 edges, 6 surfaces Per table in below Per table in below CRITERION(after test) No Crack on the FPC, on the LCD Panel No Bubbles in the LCD Panel No other Defects of Alignment in Active area Within device specifications No Broken Circuit, No Short Circuit or No Black line No Other Defects of Display Page 20 of 21

21 11. Precautions for Use of LCD Modules 11.1 Safety The liquid crystal in the LCD is poisonous. Do not put it in your mouth. If the liquid crystal touches your skin or clothes, wash it off immediately using soap and water Handling A. The LCD and touch panel is made of plate glass. Do not subject the panel to mechanical shock or to excessive force on its surface. B. Do not handle the product by holding the flexible pattern portion in order to assure the reliability C. Transparency is an important factor for the touch panel. Please wear clear finger sacks, gloves and mask to protect the touch panel from finger print or stain and also hold the portion outside the view area when handling the touch panel. D. Provide a space so that the panel does not come into contact with other components. E. To protect the product from external force, put a covering lens (acrylic board or similar board) and keep an appropriate gap between them. F. Transparent electrodes may be disconnected if the panel is used under environmental conditions where dew condensation occurs. G. Property of semiconductor devices may be affected when they are exposed to light, possibly resulting in IC malfunctions. H. To prevent such IC malfunctions, your design and mounting layout shall be done in the way that the IC is not exposed to light in actual use Static Electricity A. Ground soldering iron tips, tools and testers when they are in operation. B. Ground your body when handling the products. C. Power on the LCD module before applying the voltage to the input terminals. D. Do not apply voltage which exceeds the absolute maximum rating. E. Store the products in an antielectrostatic bag or container. 11.4Storage A. Store the products in a dark place at +25 ±10 with low humidity (40% RH to 60% RH). Don't expose to sunlight or fluorescent light. B. Storage in a clean environment, free from dust, active gas, and solvent Cleaning A. Do not wipe the touch panel with dry cloth, as it may cause scratch. B. Wipe off the stain on the product by using soft cloth moistened with ethanol. Do not allow ethanol to get in between the upper film and the bottom glass. It may cause peeling issue or defective operation. Do not use any organic solvent or detergent other than ethanol Cautions for installing and assembling Bezel edge must be positioned in the area between the Active area and iew area. The bezel may press the touch screen and cause activation if the edge touches the active area. A gap of approximately 0.5mm is needed between the bezel and the top electrode. It may cause unexpected activation if the gap is too narrow. There is a tolerance of 0.2 to 0.3mm for the outside dimensions of the touch panel and tail. A gap must be made to absorb the tolerance in the case and connector. Page 21 of 21