Sensor Actuator Interface Passive

Transcription

1 Contents Sensor Actuator Interface Passive Introduction. M distributors.8 ECO modules. M Push-Pull.6 M IDC. M VA stainless steel.8 M metal distributors.0 M distributors : Passive.6 M Combi distributor.7 M distributor for NPN and PNP sensors.8 M wall bushing.9 Solutions to customer specification. M8 distributors. M distributors.0 M distributors..

2 Introduction Sensor Actuator Interface Passive Overview Material data M M8 M Insulating material Housing PA 6 GF PT (UL 9 V0) PT (UL 9 V0) Contact carrier PA66 PT (UL 9 V0) PT (UL 9 V0) ase material Contact CuSnu. vergoldet CuSn6 CuSn6 Screw socket Temperature range C Colour Housing grey, RAL 70schwarz grey, RAL 70 grey, RAL 70 PG & contact carrier PUR black black Cable sheathing PUR PUR PUR Cable type PUR/PVC PUR/PVC halogen free, UL O-ring Viton Viton Viton Housing seal foamed PUR Type of connection, hood version 0,08,0 tension clamp screw/tension clamp Clamping range mm AWG No Stripping length, hood version mm Stripping length, screw version mm - 7 Stripping length, tension clamp version mm Contact surface verzinnt tinned tinned L. / L Contact base material CU-Legierung Cu alloy Cu alloy L. / L Torques Hoods Nm 0, lanking plugs Nm 0, Mechanical data Ingress Protection Class* IP (M6/M IP67) 68 Suitability for cable carrier cycles at d million d million d million 0d IDC connection Max. connect. frequency of a cable with same cross-section - Stripping length mm Conductor cross-section (flexible) mm - Smallest strand diameter mm - Conductor insulation material - Conductor outside diameter mm - Cable outside diameter mm - Pin assignment - Electrical data to VDE 0 (Apr 97) V Max. current carrying capacity per I/O signal A rating) (Derating) (Derating) total with single supply A 8 0 (9 A for F-version) total with dual supply A - - x 8 = 6 V eff Test voltage kv eff,0.0.0 Pollution severity Insulation resistance Ω > 0 9 > 0 9 > 0 9 Other data Dimensions see drawings on page Fixing holes see drawings on page Function indicators for operating voltage LED, green LED, green LEDs, green for I/O function LED, yellow (per function) LED, yellow (per function) LED, yellow (per function) Current isolation (SAI- -M) - via jumper plugs Cable strain relief (SAI- -M) M0 M0 Max. cable diameter (SAI- -M) mm 0 6 * only when plugged in and secured.

3 Introduction Material data Insulating material Housing Contact carrier ase material Contact Screw socket Temperature range C Colour Housing PG & contact carrier Cable sheathing Cable type O-ring Housing seal Type of connection, hood version Clamping range mm AWG No. Stripping length, hood version mm Stripping length, screw version mm Stripping length, tension clamp version mm Contact surface L. / L Contact base material L. / L Torques Hoods Nm lanking plugs Nm Mechanical data Ingress Protection Class* IP Suitability for cable carrier cycles at d IDC connection Max. connect. frequency of a cable with same cross-section Stripping length mm Conductor cross-section (flexible) mm Smallest strand diameter mm Conductor insulation material Conductor outside diameter mm Cable outside diameter mm Pin assignment Electrical data to VDE 0 (Apr 97) V- Max. current carrying capacity per I/O signal A total with single supply A total with dual supply A V eff Test voltage kv eff Pollution severity Insulation resistance Ω Other data Dimensions see drawings on page Fixing holes see drawings on page Function indicators for operating voltage for I/O function Current isolation (SAI- -M) Cable strain relief (SAI- -M) Max. cable diameter (SAI- -M) mm * only when plugged in and secured IDC PT (UL 9 V0) PT (UL 9 V0) CuZn, pre-nickeled & gold-plated grey, RAL 70 black PUR PUR/PVC Viton foamed PUR screw/tension clamp tinned CU-Alloy million d PVC/PE/PUR see next page 0 0 (Derating) 0 (9 A for F version) x 8 = 6.0 > LEDs, green LED, yellow (per function) via jumper plugs M0 6 M Push-Pull PA 6 GF PT (UL 9 V0) CuSn grey, RAL 70 black PUR halogen free, UL Viton foamed PUR tension clamp tinned CU-Alloy million 0d LED, green LED, yellow (per function) M0 6.

4 Introduction Contact assignment M connector position (view on socket) -pole Pole Colour code Assignment brown + V DC white input/output blue 0 V DC black input/output SAI-M/SAI-F IDC -pole Pole Colour code Assignment brown + V DC white input/output blue 0 V DC M8 connector position (view on socket) -pole Pole Colour code Assignment brown + V DC blue 0 V DC black input/output -pole Pole Colour code Assignment brown + V DC no colour input/output blue 0 V DC black input/output -pole Pole Colour code Assignment brown + V DC white input/output blue 0 V DC black input/output M Push-Pull connector position (view on socket) -pole Pole Colour code Assignment brown + V DC white input/output * blue 0 V DC black input/output PE *) = -pole version only M 8-pole pole Pole Colour code Assignment white signal brown signal green signal yellow signal grey + V DC 6 pink signal 7 blue 0 V DC 8 red signal 6 Pole Colour code Assignment brown + V DC blue 0 V DC white input/output green input/output pink input/output 6 yellow input/output 7 black input/output 8 grey input/output 6 9 red input/output 7 0 violet input/output 8 grey/pink input/output 9 red/blue input/output 0.

5 Introduction M -pole Pole Colour code Plug-in station Contact M white green 0 8 yellow 0 grey 7 pink PO SO red black 7 8 violet 8 9 blue ( ) 8 0 blue ( ) 8 brown (+) 8 green-yellow (PE) 8 9-pole Pole Colour code Plug-in station Contact M violet 8 red grey red/blue 0 0 green grey/pink 6 PO SO 9 8 white/green white/yellow 7 0 white/grey black 7 yellow/brown 6 brown/green white 6 yellow 7 pink 8 grey/brown 8 6 blue ( ) 8 green-yellow (PE) 8 9 brown (+) 8.

6 Introduction Connection plan Connection plan Conductor colour Terminal M/M8 contact M- IDC contact Potential Conductor colour Colour code Connection No. Connector position -pole -pole contact -pole -pole = E/A - white WH = E/A - green GN = E/A - yellow YE = E/A - grey GY = E/A - pink PK 6 = 6 E/A 6- red RD 7 = 7 E/A 7- black K 8 = 8 E/A 8- violet VT 9 = * E/A - grey/pink GYPK 0 = * E/A - red/blue RDL = * E/A - white/green WHGN = * E/A - brown/green NGN = * E/A - white/yellow WHYE = 6 * E/A 6- yellow/brown YEN = 7 * E/A 7- white/grey WHGY 6 = 8 * E/A 8- grey/brown GYN 7 =,,, 7 U + ( V DC) brown N 8 =,,, 7 U - (0 V) blue U 9 =,, 6, 8 U + ( V DC) red* RD* 0 =,, 6, 8 U - (0 V) black* K* =,,,,, 6, 7, PE green/yellow GNYE * Contact used in -pole version only Plug insert, hood version Note: SAI distributors with fixed cable have a single supply conductor as standard. The voltage U is supplied to all the sockets. An SAI distributor with fixed cable but with separate supply voltage is available on request. Tension clamp connection Pin assignment Screw connection.6

7 Introduction Are you already a Weidmüller customer? Then why not order your M or M8 cables from us! Weidmüller supplies an extremely wide range of M and M8 cables naturally with proven Weidmüller quality. To answer as many demands as possible, we offer: PVC cables PUR/PVC cables PUR/halogen-free cables Of course, with very short delivery times and favourable conditions. Do not hesitate to contact us. Ask for a bid. It doesn t hurt to ask..7

8 M distributors SAI distributor with plug-in connection hood: SAI-M Integrated plug-in connector in connection hood M robust metal thread for sensor/actuator connection, now also available with plastic thread as an alternative Quick replacement of bus cables us cable can be supplied pre-assembled Two connection systems for bus cable: screw or tension clamp Very flat connection hood: no higher than smallest 90 M round plug Distributor and connection hood can be supplied separately Connection hood compatible with -, 6- and 8-channel SAI distributors (upgrades only entail changing the base module) IP 68 Ingress protection class (IDC IP 67), Housing made from Pocan (PT): high dimensional stability good electrical and mechanical properties flame-retardant without dioxin or furan formers resistant to coolants and lubricants UL/CSA approvals for M SAI distributor SAI distributor available in pollution severity class Cable exit on top Weidmüller SAI distributors have the largest storage capacity in the connection hood Female connectors integrated into the metal plate for fast and reliable connections Wide range of M8 and M cables and plug-in connectors Various cable length's available Metal hoods and housings also available Plug-in connection module for bus cables increases flexibility on site Integral, plug-in electrical isolation for two separate electric circuits (e.g. for emergency stop) Simple and vibration-resistant connections on site Captive metric screws (grade 8.8 steel) have a +/- head M and IDC connections : arrangement available.8

9 M distributors Overview of M Distributors Fixed cable version Pre-assembled bus cable minimises installation time and reduces wiring errors Cable carrier-compatible versions are available with polyurethane (PUR) sheathing M Push-Pull quick-fit connection system M Push-Pull is the new connection system for sensors and actuators. It is downward-compatible to the existing M system, which means that both old M and new M Push-Pull lines can be used together on these SAIs. M Push-Pull decreases installation time and increases installation safety by means of colour coding and provides an audible click on locking for added reassurance. SAI ECO the cost-effective alternative Weidmüller SAI distributors with hood have long since been standard fittings in machines and installations. Why plastic threaded rings? There were some applications, however, that called for a further version. In some applications it is necessary to avoid all metal parts, unless these are made from stainless steel. In such cases stainless steel is then used for screws and nuts only, but the M threaded rings can also be made from plastic. Such modules can now be supplied on request. The use of plastic rings therefore results in a cheaper alternative. Although the service life and resistance are reduced when compared to metal, this is acceptable for some applications..9

10 M distributors Hood version SAI -M =0 SAI 6-M =7 SAI 8-M = Complete modules Without initiator-led, for analogue signals Without initiator-led, for analogue signals ase unit Without initiator-led, for analogue signals Mounting hood Screw connection SAI-/6/8-M -pole SAI--M P M SAI-6-M P M SAI-8-M P M SAI- M P M UT SAI-6-M P M UT SAI-8-M P M UT SAI-/6/8-MH LZF SAI-/6/8-MH LZF. SV SAI-/6/8-MH L SAI-/6/8-M -pole SAI--M P M SAI-6-M P M SAI-8-M P M SAI--M P M OL SAI-8-M P M OL SAI-8-M P M ZF III SAI--M P M UT SAI-6-M P M UT SAI-8-M P M UT SAI-8-M P M OL UT SAI-/6/8-MH LZF SAI-/6/8-MH LZF. SV SAI-/6/8-MH L Complete without LED Complete modules, NPN-switched SAI-8-M P M OL SAI-8-M P M NPN Note.0 V DC blue red blue red 0 V 0 V DC Max. current carrying capacity per input/output signal A Max. current carrying capacity per slot A Max. total current 0 A Pollution severity Ingress protection class IP 68 Ambient temperature range -0 C 90 C Housing material Pocan Contact carrier PT UL 9 V0 ase material of contacts CuZn, pre-nickeled and gold-plated Threaded bush Housing colour grey, RAL 70 Flammability class UL 9 V-0 Clamping range of hood version 0.08 mm. mm Dragline compatible (fixed cable connection) 8-way 8-way 6-way -way With dual power supply x 8 = 6 A total current Clamping range up to. mm with screw connection.0

11 M distributors Fixed cable version SAI -F = 0 SAI 6-F = 7 SAI 8-F = Cable length m Cable length m Cable length 0 m Cable length m Cable length 0 m Cable length m Cable length m Cable length 0 m Cable length m Cable length 0 m Cable length m Cable length m Cable length 0 m Cable length m Cable length 0 m with reinforced fixed cable* Cable length m Cable length m Cable length 0 m Cable length m Cable length 0 m SAI-/6/8-F -pole SAI--F P PUR M SAI--F P PUR M SAI--F P PUR 0M SAI--F P PUR M SAI--F P PUR 0M SAI-6-F P PUR M SAI-6-F P PUR M SAI-6-F P PUR 0M SAI-6-F P PUR M SAI-6-F P PUR 0M SAI-8-F P PUR M SAI-8-F P PUR M SAI-8-F P PUR 0M SAI-8-F P PUR M SAI-8-F P PUR 0M SAI-/6/8-F -pole SAI--F P PUR M SAI--F P PUR M SAI--F P PUR 0M SAI--F P PUR M SAI--F P PUR 0M SAI-6-F P PUR M SAI-6-F P PUR M SAI-6-F P PUR 0M SAI-6-F P PUR M SAI-6-F P PUR 0M SAI-8-F P PUR M SAI-8-F P PUR M SAI-8-F P PUR 0M SAI-8-F P PUR M SAI-8-F P PUR 0M SAI-8-F P M 0./.0U SAI-8-F P M 0./.0U SAI-8-F P 0M 0./.0U SAI-8-F P M 0./.0U SAI-8-F P 0M 0./.0U Note.0 V DC 0 V 0 V DC Max. current carrying capacity per input/output signal A max. current carrying capacity per slot A Max. total current 9 A Pollution severity Ingress protection class IP 68 Ambient temperature range -0 C 80 C Housing material Pocan Contact carrier PT UL 9 V0 ase material of contacts CuZn, pre-nickeled and gold-plated Threaded bush Housing colour grey, RAL 70 Flammability class UL 9 V-0 Clamping range of hood-version Dragline compatible Yes (fixed cable connection) * x mm and 6 x 0. mm, total current A green-yellow brown blue white green yellow grey pink red black violet 8-way 6-way -way grey-pink red-blue white-green brown-green white-yellow yellow-brown white-grey grey-brown green-yellow brown blue white green yellow grey pink red black violet 8-way 6-way -way.

12 M distributors with M outlet M Complete modules Without initiator-led, for analogue signals Without initiator-led, for analogue signals ase unit Without initiator-led, for analogue signals Mounting hood Screw connection SAI-/6/8-S -pole SAI--S P M SAI-6-S P M SAI-8-S P M SAI-/6/8-S -pole SAI--S P M SAI-6-S P M SAI-8-S P M Note.0 V DC 0 V 0 V DC Max. current carrying capacity per input/output signal A Max. current carrying capacity per slot A Max. total current 0 A Pollution severity Ingress protection class IP 68 Ambient temperature range -0 C 90 C Housing material Pocan Contact carrier PT UL 9 V0 ase material of contacts CuZn, pre-nickeled and gold-plated Threaded bush Housing colour grey, RAL 70 Flammability class UL 9 V-0 Clamping range of hood version Dragline compatible (fixed cable connection) sock 8 sock 7 sock 6 sock sock sock sock PE (+) SAI-6-S sock 8 x ye gr gr 0 (-) 9 (-) SAI-8-S.

13 M distributors with M6 outlet SAI -S = 0 SAI 6-S = 7 SAI 8-S = M Complete modules Without initiator-led, for analogue signals Without initiator-led, for analogue signals ase unit Without initiator-led, for analogue signals Mounting hood Screw connection SAI-8-M6 -pole SAI-8-M6 P M Note.0 V DC 0 V 0 V DC Max. current carrying capacity per input/output signal A Max. current carrying capacity per slot A Max. total current 6 A Pollution severity Ingress protection class IP 67 Ambient temperature range -0 C 90 C Housing material Pocan Contact carrier PT UL 9 V0 ase material of contacts CuZn, pre-nickeled and gold-plated Threaded bush Housing colour grey, RAL 70 Flammability class UL 9 V-0 Clamping range of hood version Dragline compatible (fixed cable connection) sock sock sock sock sock sock 6 sock 7 PE JL CM F G H K A D sock 8 E H M G F E D J K A L C.

14 ECO modules SAI ECO SAI ECO the cost-effective alternative Cost-effective alternative The Weidmüller SAI distributors with hoods have long since been standard fittings in machines and installations. Why plastic threaded rings? There were some applications, however, that called for a further version. In some applications it is necessary to avoid all metal parts. In such cases stainless steel is then used for screws and nuts only, but the M threaded rings can also be made from plastic. Such modules can now be supplied on request. The use of plastic rings therefore results in a cheaper alternative. Although the service life and resistance are reduced when compared to metal, this is acceptable for some applications. The ECO modules were developed to optimise costs. Many details of these modules were adapted in such a way that they can still be used wherever standard modules were used in the past, but the individual solutions have now become simpler: One-way disconnector: Up until now it was usual to achieve electrical isolation devised by Weidmüller by way of jumpers. To reduce costs, these jumpers have been replaced by solder bridges. These are simply cut to provide electrical isolation. No protective caps: Normally, Weidmüller M distributors are always supplied with two protective caps. These were not always required and so they have been omitted. Standard cable gland: The vibration-resistant black screw cable gland has been replaced by a standard IP 68 cable gland. These cost-cutting measures result in yet more applications for Weidmüller SAI distributors. Greater reliability than with comparable systems Plastic threaded rings are nothing new. However, the problem in the past was that the threaded rings formed part of the housing and were therefore made from the same plastic. Weidmüller has once again pioneered a new and better solution. Weidmüller plastic rings are manufactured separately, which means that a more suitable, more durable material can be chosen. The Weidmüller production method is also patented. Special threaded ring increases durability.

15 ECO modules Hood version SAI -M =0 SAI 6-M =7 SAI 8-M = Complete modules NPN NPN ase unit Without initiator-led, for analogue signals Mounting hood Screw connection -pole SAI-/6/8-M -pole SAI--M P M ECO SAI-6-M P M ECO SAI-8-M P M ECO SAI--M P M NPN ECO SAI-8-M P M NPN ECO Complete without LED Complete modules, NPN-switched Note These distributors are supplied without protective caps and markers..0 V DC blue red 0 V 0 V DC Max. current carrying capacity per input/output signal A Max. current carrying capacity per slot A Max. total current 0 A Pollution severity Ingress protection class IP 68 Ambient temperature range -0 C 90 C Housing material Pocan Contact carrier PT UL 9 V0 ase material of contacts CuZn, pre-nickeled and gold-plated Threaded bush Pocan Housing colour grey, RAL 70 Flammability class UL 9 V-0 Clamping range of hood version 0.08 mm. mm Dragline compatible (fixed cable connection) 8-way 6-way -way.

16 M Push-Pull M Push-Pull: SAI distributors and cables, with rapid-connection technology SAI distributors with M Push-Pull plug Whereas the standard M system requires the sleeves to be laboriously screwed on and that operation is hindered by the vibration guard, M Push-Pull works with one click, just like those well-known garden hose systems. The audible locking function guarantees a safe and reliable connection as well as a good seal. M Push-Pull is currently supplied by Weidmüller and five other international companies M Push-Pull M versions M Push-Pull connections provide sufficient space for using T-pieces. The SAI module is slimmer and now only mm wide. The new SAI M Push-Pull distributors can be used with M plug-in connectors but also with the new M Push-Pull plug-in connectors. The SAI distributors are available in fixed cable, hood, bayonet connection and M versions. M Push-Pull speeds up installation and increases installation reliability thanks to the colour coding and the audible click when locking it into place. M Push-Pull hood version M Push-Pull with bayonet connection.6

17 M Push-Pull Fixed cable version with reinforced fixed cable Cable length m Cable length m Cable length 0 m Cable length m Cable length 0 m Cable length m Cable length m Cable length 0 m Cable length m Cable length 0 m Cable length m Cable length m Cable length 0 m Cable length m Cable length 0 m Cable length m Cable length m Cable length 0 m Cable length m Cable length 0 m SAI-/8-F -pole SAI--F P FC M SAI--F P FC 0M SAI-8-F P FC M SAI-8-F P FC 0M SAI-/8-F -pole SAI--F P FC M SAI--F P FC 0M SAI-8-F P FC M SAI-8-F P FC 0M Note.0 V DC 0 V 0 V DC Max. current carrying capacity per input/output signal A max. current carrying capacity per slot A Max. total current 0 A Pollution severity Ingress protection class IP 67 Ambient temperature range - C 80 C Housing material PA 6 GF Contact carrier PT UL 9 V0 ase material of contacts CuZn, pre-nickeled and gold-plated Threaded bush Housing colour grey, RAL 70 Flammability class UL 9 Clamping range of hood-version Dragline compatible Yes (fixed cable connection) Trunk cable x mm x n x 0. mm ; halogen sock sock sock sock sock sock6 sock7 sock8 LED_gn gn/ye br bl wh gn ye gr pi re bk vi 8-way -way sock sock sock sock sock sock6 sock7 sock8 gn/ye br LED_gn bl gr/pi wh re/bl gn wh/gn ye br/gn gr wh/ye rs ye/br re wh/gr bk gr/br vi 8-way -way.7

18 M Push-Pull with M outlet Complete modules Without initiator-led, for analogue signals Without initiator-led, for analogue signals ase unit Without initiator-led, for analogue signals Mounting hood Screw connection SAI-/8-S -pole SAI--S P FC SAI-8-S P FC SAI-/8-S -pole SAI--S P FC SAI-8-S P FC Note.0 V DC 0 V 0 V DC Max. current carrying capacity per input/output signal A Max. current carrying capacity per slot A Max. total current 9 A Pollution severity Ingress protection class IP 67 Ambient temperature range - C 80 C Housing material PA 6 GF Contact carrier PT UL 9 V0 ase material of contacts CuZn, pre-nickeled and gold-plated Threaded bush Housing colour grey, RAL 70 Flammability class UL 9 Clamping range of hood version Dragline compatible (fixed cable connection) sock sock sock sock sock sock6 sock7 sock8 LED_gn way -way sock sock sock sock sock sock6 sock7 sock8 9 LED_gn way -way.8

19 M Push-Pull with M outlet on front M 9 6 Complete modules Without initiator-led, for analogue signals Without initiator-led, for analogue signals ase unit Without initiator-led, for analogue signals Mounting hood Screw connection SAI-/8-SH -pole SAI--SH P FC SAI-8-SH P FC SAI-/8-SH -pole SAI--SH P FC SAI-8-SH P FC Note.0 V DC 0 V 0 V DC Max. current carrying capacity per input/output signal A Max. current carrying capacity per slot A Max. total current 9 A Pollution severity Ingress protection class IP 67 Ambient temperature range - C 80 C Housing material PA 6 GF Contact carrier PT UL 9 V0 ase material of contacts CuZn, pre-nickeled and gold-plated Threaded bush Housing colour grey, RAL 70 Flammability class UL 9 Clamping range of hood version Dragline compatible (fixed cable connection) -way 8-way sock8 sock7 sock6 sock sock sock sock -way 8-way sock8 sock7 sock6 sock sock sock sock sock sock LED_gn LED_gn.9

20 M Push-Pull Hood version Complete modules Without initiator-led, for analogue signals Without initiator-led, for analogue signals ase unit Without initiator-led, for analogue signals Mounting hood Screw connection -pole SAI-8-M -pole SAI-8-M P FC Complete without LED Complete modules, NPN-switched Note.0 V DC 0 V 0 V DC Max. current carrying capacity per input/output signal A 8 x ye 8 x ye Max. current carrying capacity per slot A Max. total current 9 A Pollution severity Ingress protection class IP 67 Ambient temperature range - C 80 C Housing material PA 6 GF Contact carrier PT UL 9 V0 ase material of contacts CuZn, pre-nickeled and gold-plated Threaded bush Housing colour grey, RAL 70 Flammability class UL 9 Clamping range of hood version Dragline compatible (fixed cable connection) Terminal PE Slot M Contact Colour white green yellow grey pink red black violet grey/pink red/blue white/green brown/green white/yellow yellow/brown white/grey grey/brown brown (+) blue ( ) green/yellow (PE) Code WH GN YE GY PK RD K VT GYPK RDU WHGN NGN WHYE YEN WHGY GYN N (+) U ( ) GNYE -way 8-way.0

21 M Push-Pull CNOMO SAI-/8-S -pole SAI-/8-F -pole -channel m cable m cable SAI--F P CNOMO M m cable SAI--F P CNOMO 0M m cable 0 m cable 6-channel m cable m cable 0 m cable m cable 0 m cable 8-channel m cable m cable SAI-8-F P CNOMO M m cable SAI-8-F P CNOMO 0M m cable 0 m cable M -channel SAI--S P CNOMO channel SAI-8-S P CNOMO Note See drawing on page.8 0 V DC 0 V DC 0 V DC Max. current-carrying capacity per I/O signal A Max. current-carrying capacity per channel A Max. total current A; 8 A Pollution severity Ingress protection class IP 67 Ambient temperature range - C 80 C Housing material PA 6 GF Contact carrier PT (UL 9 V0) ase material of contacts CuZn, pre-nickeled & gold-plated Threaded bush Housing colour grey, RAL 70 Flammability class to UL9 Clamping range of hood version Cable carrier-compatible yes (fixed cable connection) Max. total current is 8 A for a -channel distributor, A for an 8-channel distributor. -way 8-way Sock Sock Sock Sock 7 U-M-P U-M-P U-M-P U-M-P ST-M-9P Sock Sock Sock 6 Sock 8 U-M-P U-M-P U-M-P U-M-P vi bk re pi gr ye gn wh bl ( ) br (+) gn/ye PE sock8 sock7 sock6 sock sock sock sock sock gr/br wh/gr ye/br wh/ye br/gn wh/gn re/bl gr/pi -way 8-way Numbers for designation on PC.

22 M Push-Pull ayonet joint Complete modules Without initiator-led, for analogue signals Without initiator-led, for analogue signals ase unit Without initiator-led, for analogue signals Mounting hood Screw connection -pole SAI-8-SH -pole SAI-8-SH P FC Complete without LED Complete modules, NPN-switched Note.0 V DC 0 V 0 V DC Max. current carrying capacity per input/output signal Max. current carrying capacity per slot A A violet 8 sock8 6 grey-brown Max. total current 9 A Pollution severity black 7 sock7 white-grey Ingress protection class IP 67 Ambient temperature range - C 80 C red 6 sock6 yellow-brown Housing material PA 6 GF Contact carrier PT UL 9 V0 ase material of contacts CuZn, pre-nickeled and gold-plated pink sock white-brown Threaded bush Housing colour grey, RAL 70 grey sock brown-green Flammability class UL 9 Clamping range of hood version yellow sock white-green Dragline compatible (fixed cable connection) green sock 0 red-blue white sock 9 grey-pink blue 8 brown 7 green-yellow PE.

23 M Push-Pull ayonet joint with socket connector on reverse Complete modules Without initiator-led, for analogue signals Without initiator-led, for analogue signals ase unit Without initiator-led, for analogue signals Mounting hood Screw connection -pole SAI-8-SH -pole SAI-8-SH P F FC Complete without LED Complete modules, NPN-switched Note.0 V DC 0 V 0 V DC Max. current carrying capacity per input/output signal A Max. current carrying capacity per slot A Max. total current 9 A Pollution severity Ingress protection class IP 67 Ambient temperature range - C 80 C Housing material PA 6 GF Contact carrier PT UL 9 V0 ase material of contacts CuZn, pre-nickeled and gold-plated Threaded bush Housing colour grey, RAL 70 Flammability class UL 9 Clamping range of hood version Dragline compatible (fixed cable connection) Shield V 8 x yellow green Terminal Terminal 0 Terminal 9 Terminal 8 Terminal (KSR ) 7 Terminal + V (Thermocontact) 6 Terminal Terminal (KSR ) Terminal (Shield-KSR) Terminal (Thermocontact) Terminal Terminal Terminal Female connector pole at rear.

24 M IDC IDC the quick connection Hood version (+) (-) (+) (-) Factory Lieferzustand setting (see(siehe wiring Schaltplan) diagram) Potential gebrückt Potential getrennt Current bridged Current isolated Compact IDC connection cuts production, commissioning and maintenance work Knurled metal nut robust, safe handling requiring little force The dimensions of the IDC distributor correspond to and are compatible with the standard SAI distributor. Plug-in connection module for bus cables enhances on-site flexibility Three sizes for, 6 and s -pole version with one I/O signal per channel, -pole version with two I/O signals per channel Individual on-site assembly of sensor/actuator lines Fast, reliable connection with IDC connection element IP 67 Ingress protection classification. SAI fixed cable version Pre-assembled bus cables minimise installation work and avoid wiring errors sizes for, 6 and s Highly flexible, cable carrier-compatible bus cables with polyurethane (PUR/PVC) sheathing x 0.7 mm n x 0. mm, -pole version with one I/O signal per channel, -pole version with two I/O signals per channel IDC connection element SAI-SA--IDC SAI-SA--IDC

25 M IDC The significant advantages of Weidmüller tools: Easy handling Very small, ideal for confined assembly conditions Patented solution Metal Connectors Insulation displacement connections on Weidmüller SAI distributors are currently the smallest but also the most robust connection elements on the market. Thanks to their extremely small dimensions, corresponding distributors are available with the same dimensions in M or IDC versions. For large series, e.g. where more than 00 modules are used every year, we recommend using a special tool to simplify the handling of the connected lines even further. However, this tool is not always necessary because all connection elements can be readily tightened by hand. IDC tool SAI-IDC-Tool Screwty The IDC elements can also be tightened with the Weidmüller Screwty. Screwty M Protective cap M for IDC SAI-SK-M IDC

26 M IDC Hood version SAI -M =0 SAI 6-M =07 SAI 8-M = Complete modules Without initiator-led, for analogue signals Without initiator-led, for analogue signals ase unit Without initiator-led, for analogue signals Mounting hood Screw connection SAI-/6/8-M IDC -pole SAI--M P IDC SAI-6-M P IDC SAI-8-M P IDC SAI--M P IDC UT SAI-6-M P IDC UT SAI-8-M P IDC UT SAI-/6/8-MH LZF SAI-/6/8-MH L SAI-/6/8-M IDC -pole SAI--M P IDC SAI-6-M P IDC SAI-8-M P IDC SAI--M P IDC UT SAI-6-M P IDC UT SAI-8-M P IDC UT SAI-/6/8-MH LZF SAI-/6/8-MH L Note.0 V DC blue red blue red 0 V 0 V DC Max. current carrying capacity per input/output signal A Max. current carrying capacity per slot A Max. total current 0 A Pollution severity Ingress protection class IP 67 Ambient temperature range -0 C 90 C Housing material Pocan Contact carrier PT UL 9 V0 ase material of contacts Threaded bush Housing colour grey, RAL 70 Flammability class UL 9 V-0 Clamping range of hood version 0.08 mm. mm Dragline compatible (fixed cable connection) 8-way 6-way -way 8-way 6-way -way With dual power supply x 8 = 6 A total current Clamping range up to. mm with screw connection.6

27 M IDC Fixed cable version SAI =0 SAI 6 =7 SAI 8 = with reinforced fixed cable Cable length m Cable length m Cable length 0 m Cable length m Cable length 0 m Cable length m Cable length m Cable length 0 m Cable length m Cable length 0 m Cable length m Cable length m Cable length 0 m Cable length m Cable length 0 m Cable length m Cable length m Cable length 0 m Cable length m Cable length 0 m SAI-/6/8-F IDC -pole SAI--F P IDC PUR M SAI--F P IDC PUR 0M SAI-6-F P IDC PUR M SAI-6-F P IDC PUR 0M SAI-8-F P IDC PUR M SAI-8-F P IDC PUR 0M SAI-/6/8-F IDC -pole SAI--F P IDC PUR M SAI--F P IDC PUR 0M SAI-6-F P IDC PUR M SAI-6-F P IDC PUR 0M SAI-8-F P IDC PUR M SAI-8-F P IDC PUR 0M Note.0 V DC 0 V 0 V DC Max. current carrying capacity per input/output signal A max. current carrying capacity per slot A Max. total current 9 A Pollution severity Ingress protection class IP 67 Ambient temperature range -0 C 80 C Housing material Pocan Contact carrier PT UL 9 V0 ase material of contacts Threaded bush Housing colour grey, RAL 70 Flammability class UL 9 V-0 Clamping range of hood-version Dragline compatible Yes (fixed cable connection) brown blue white green yellow grey pink red black violet 8-way 6-way -way grey/pink red/blue white/green brown/green white/yellow yellow/brown white/grey grey/brown brown blue white green yellow grey pink red black violet 8-way 6-way -way.7

28 M VA stainless steel Fixed cable version -pole, signals per socket green LED operating indicator and yellow LED function indicator with stainless steel housing and cable glands Ideal for machinery within the Food and everage Industries SAI-8-F P M M VA M connectors in stainless steel SAI-8-F P M M VA -pole SAI-8-F P M M VA SAIS-/9-VA Note Temperature range 0 C/+ 60 C Materials: Housing stainless steel.0/6l Contact carrier PVC sock LED_gn gn/ye br bl wh Contact Threaded bush O-ring CuZn, pre-nickeled & 0.8 μm gold plating stainless steel.0/6l EPDM sock gn Mechanical data: Ingress protection class IP69K only in screwed condition with associated mating pieces Electrical data: Contact resistance mω Current-carrying capacity A per channel A max. total 0-0 V DC V AC eff Pollution severity to VDE 00 Accessories (included) protective caps for channels not assigned sock sock sock sock6 sock7 sock8 ye gr pi re bk vi 8-way -way Pin assignment 8-channel = brown = grey/pink red/blue white/green brown/green white/yellow yellow/brown white/grey grey/brown = blue = white green yellow grey pink black violet = green/yellow.8

29 .9

30 M metal distributors Sensor-actuator distributors for special applications All-metal SAI-/8-FMM M Shielded cable, e.g. for analogue initiators Some applications need full shielding from sensor to control. This is possible with the all-metal SAI distributors. The distributors are supplied with an EMC cable gland. Initiator LEDs are omitted. Especially thick trunk cable It is sometimes advisable to use the machine manufacturer s standard trunk cable. This cable will usually have a relatively large outside diameter and will therefore require plenty of space (SAI-/6/8 MHD). All-metal fixed cable distributors Weidmüller metal distributors have proved their worth in many situations. They are available as - and 8-channel M versions with cable lengths of or 0 m. Metal distributors are also necessary when ESD requirements must be complied with. The conductive metal surface provides low surface resistance. Advantages: no ESD/EMC problems high resistance to chemicals or mechanical loads standard mounting dimensions SAI-M with metal hood SAI-/6/8 MMS SAI-/6/8 MM MMS: Modular, Metal, Shield MM: Modular, Metal SAI-/6/8 MH MH: Modular, High SAI-/6/8 MHD MHD: Modular, High, sealed (for especially thick cables) SAI-/6/8 MMS with EMC cable gland in metal housing Especially tough conditions where plastic is totally unsuitable. In certain cases it makes sense to avoid the use of plastics altogether. In such cases a distributor made completely from metal is required that can be connected to others using metal cable glands, without additional connections for the shielding. Cable gland: M0 For cables with outside insulation diameter from 0 mm to mm. Listed below are just some of the cable sizes that are suitable for the SAI distributor with M0 cable gland: x 0.0 mm to 6 x 0.0 mm 8 x 0.7 mm to x 0.7 mm 8 x.00 mm to 0 x.00 mm x.0 mm to 7 x.0 mm Cable gland: M For cables with outside insulation diameter from mm to 8 mm. Listed below are just some of the cable sizes that are suitable for the SAI distributor with M cable gland: x 0.0 mm 8 x 0.7 mm to x 0.7 mm x.00 mm to 0 x.00 mm 8 x.0 mm to 6 x.0 mm.0

31 M metal distributors Overview of metal distributors Type SAI-UT Sockets M Poles Hood Form Cable gland Cable gland Length Order No. SAI--MH-P M PT Zn-G high M0 plastic SAI-6-MH-P M PT 6 Zn-G high M0 plastic SAI-8-MH-P M PT 8 Zn-G high M0 plastic SAI--MH-P M PT Zn-G high M0 plastic SAI-6-MH-P M PT 6 Zn-G high M0 plastic SAI-8-MH-P M PT 8 Zn-G high M0 plastic SAI--MHD-P M PT Zn-G high M plastic SAI-6-MHD-P M PT 6 Zn-G high M plastic SAI-8-MHD-P M PT 8 Zn-G high M plastic SAI--MHD-P M PT Zn-G high M plastic SAI-6-MHD-P M PT 6 Zn-G high M plastic SAI-8-MHD-P M PT 8 Zn-G high M plastic SAI--MMS-P M Zn-G Zn-G low M0 EMC SAI-8-MMS-P M Zn-G 8 Zn-G low M0 EMC SAI--MMS-P M Zn-G Zn-G low M0 EMC SAI-8-MMS-P M Zn-G 8 Zn-G low M0 EMC SAI--MM-P M Zn-G Zn-G low M0 brass SAI-8-MM-P M Zn-G 8 Zn-G low M0 brass SAI-/6/8 MH-MH L. Zn-G high M0 plastic SAI-/6/8 MH-MHD L. Zn-G high M plastic SAI-8-MH-P M ZF III PT 8 Zn-G high M0 plastic SAI-8-MMS-P M ZF III Zn-G 8 Zn-G high M0 plastic SAI-/6/8 MH-MH L-ZF. Zn-G high M0 plastic SAI--FMM-P M M Zn-G m SAI--FMM-P M 0M Zn-G 0 m SAI-8-FMM-P M M Zn-G 8 m SAI-8-FMM-P M 0M Zn-G 8 0 m Note: The cable outside diameter can vary from manufacturer to manufacturer. It is therefore possible that the cable glands hold other cables firmly despite a different strand lay-up. In each case, it is best to first measure the cable diameter and then choose an appropriate distributor..

32 M metal distributors Hood version SAI -M=0 SAI 6-M=7 SAI 8-M= 60 8 Complete modules Without initiator-led, for analogue signals Without initiator-led, for analogue signals ase unit Without initiator-led, for analogue signals Mounting hood Screw connection SAI-/6/8-MM -pole SAI--MMS P M SAI-8-MMS P M SAI-/6/8 MH-MM L SAI-/6/8-MM -pole SAI--MM P M SAI-8-MM P M SAI--MMS P M SAI-8-MMS P M SAI-8-MMH P M ZF SAI-8-MM-P M UT SAI-/6/8 MH-MM L Note MM without initiator LED and with standard metal cable gland.0 V DC 0 V 0 V DC Max. current carrying capacity per input/output signal A Max. current carrying capacity per slot A Max. total current 0 A Pollution severity Ingress protection class IP 68 Ambient temperature range -0 C 90 C Housing material Contact carrier PT UL 9 V0 ase material of contacts CuZn, pre-nickeled and gold-plated Threaded bush Housing colour silver Flammability class UL 9 V-0 Clamping range of hood version 0.08 mm. mm Dragline compatible (fixed cable connection) 8-way 6-way -way 8-way 6-way -way.

33 M metal distributors Fixed cable version SAI = 0 SAI 6 = 7 SAI 8 = SAI--FMM -pole Cable length m Cable length m SAI--FMM-P M M Cable length 0 m SAI--FMM-P M 0M Cable length m Cable length 0 m Cable length m Cable length m Cable length 0 m Cable length m Cable length 0 m Cable length m Cable length m SAI-8-FMM-P M M Cable length 0 m SAI-8-FMM-P M 0M Cable length m Cable length 0 m with reinforced fixed cable Cable length m Cable length m Cable length 0 m Cable length m Cable length 0 m Note.0 V DC 0 V 0 V DC 8-way -way Max. current carrying capacity per input/output signal A max. current carrying capacity per slot A Max. total current 9 A Pollution severity U U-M-P-PA U U-M-P-PA Ingress protection class IP 68 Ambient temperature range -0 C 90 C Housing material Contact carrier PT UL 9 V0 U6 U-M-P-PA U U-M-P-PA ase material of contacts CuZn, pre-nickeled and gold-plated Threaded bush Housing colour silver Flammability class UL 9 V-0 U7 U-M-P-PA U U-M-P-PA Clamping range of hood-version Dragline compatible (fixed cable connection) Yes U8 U-M-P-PA U U-M-P-PA PK WHYE RD YEN K WHGY VT GYN WH GYPK GN RDU YE WHGN GY NGN U (-) N (+) GNYE V LED-GN R K7 PE 6.

34 M metal distributors Hood version with M0 outlet For cables with 0- mm outer diameter SAI -M =0 SAI 6-M = SAI 8-M =6, 60 8 Complete modules Without initiator-led, for analogue signals Without initiator-led, for analogue signals ase unit Without initiator-led, for analogue signals Mounting hood Screw connection SAI-/6/8-MH -pole SAI--MH-P M SAI-6-MH-P M SAI-8-MH-P M SAI-/6/8 MH MH LZF, SAI-/6/8 MH-MH L SAI-/6/8-MH -pole SAI--MH-P M SAI-6-MH-P M SAI-8-MH-P M SAI-8-MH-P M ZF III SAI-/6/8 MH MH LZF, SAI-/6/8 MH-MH L Note.0 V DC blue red blue red 0 V 0 V DC Max. current carrying capacity per input/output signal A Max. current carrying capacity per slot A Max. total current 0 A Pollution severity Ingress protection class IP 68 Ambient temperature range -0 C 90 C Housing material Contact carrier PT UL 9 V0 ase material of contacts CuZn, pre-nickeled and gold-plated Threaded bush Housing colour silver Flammability class UL 9 V-0 Clamping range of hood version 0.08 mm. mm Dragline compatible (fixed cable connection) 8-way 6-way -way 8-way 6-way -way With dual power supply x 8 = 6 A total current Clamping range up to. mm with screw connection.

35 M metal distributors Hood version with M outlet For cables with -8 mm outer diameter SAI -M =0 SAI 6-M = SAI 8-M = Complete modules Without initiator-led, for analogue signals Without initiator-led, for analogue signals ase unit Without initiator-led, for analogue signals Mounting hood Screw connection SAI-/6/8-MHD -pole SAI--MHD-P M SAI-6-MHD-P M SAI-8-MHD-P M SAI-/6/8 MH-MHD L SAI-/6/8-MHD -pole SAI--MHD-P M SAI-6-MHD-P M SAI-8-MHD-P M SAI-/6/8 MH-MHD L Note.0 V DC blue red blue red 0 V 0 V DC Max. current carrying capacity per input/output signal A Max. current carrying capacity per slot A Max. total current 0 A Pollution severity Ingress protection class IP 68 Ambient temperature range -0 C 90 C Housing material Contact carrier PT UL 9 V0 ase material of contacts CuZn, pre-nickeled and gold-plated Threaded bush Housing colour silver Flammability class UL 9 V-0 Clamping range of hood version 0.08 mm. mm Dragline compatible (fixed cable connection) 8-way 6-way -way 8-way 6-way -way With dual power supply x 8 = 6 A total current Clamping range up to. mm with screw connection.

36 M distributors : Passive For circuits with five floating contacts in one M with hood Emergency stop wiring Sometimes a machine builder will need more than two floating contacts in one M plug-in connector. This is the case, for example, in the wiring for some emergency stop circuits. It was for this application that Weidmüller developed the : SAI distributor. This SAI distributor has four M plug-in connectors with five floating contacts in one socket connector. The distributor is supplied complete with hood. When connecting PT00 - and -conductor initiators, we recommend the new shielded metal version. If you need other circuit configurations, simply contact us. base element metal Note: This distributor should not be used as base module for active bus distributors. Socket Contact L. contact Current per channel Total current LEDs A 8 A No LEDs are integrated at any point. SAI--M P M : (plastic hood) ase element (plastic) SAI--MMS P M : (Metal hood)

37 M Combi distributor SAI distributor with 8 poles per M Applications This distributor can be used both as a base module for satellite solutions (SAI-Combi) and for connecting sensors/units with more than two contacts. SAI-Combi A sub-distribution board can be connec-ted to every M with the help of the SAI--M 8P in conjunction with the SAI Active bus hood. This SAI should then be a -channel distributor with one channel per socket. The SAI--M P M is particularly suitable. Part No Sensors, units with more than two signals in one line As one socket in this module contains four signal paths and, in addition, two +, two and one PE, components with more than two signal lines can be connected to this module. Eight-pole connecting cables are available on request. Wiring M socket M contact L. connection PLC input Supply E0.0 E0. E0. 7 E0. E0. E0. 6 E0.6 8 E0.7 9 E.0 E. E. E. 0 E. E. E.6 6 E.7 / 7 V / 9 V / 6/7 8 0 V / 6/7 0 0 V /// 8 PE PE The jumpers in the distributor enable the potentials of 7 and 9 or 8 and 0 to be bridged Contacts 6 and 7 are bridged in the 8-pole M in order to increase the current-carrying capacity. total current per M: A, signal current per pin: A Complete module: SAI--M 8P M ase separate: SAI--M M UT Matching hood passive: SAI-/6/8-MH-L Technical information : The distributor does not include any signalling LEDs. Supply LEDs and electrical isolation are provided..7

38 M distributor for NPN and PNP sensors Fixed cable version Fixed cable version This distributor includes the option of attaching either a PNP sensor or an NPN sensor with - or -conductor connection to an M socket. Eight inputs are available in total. In the case of a switched sensor, a + signal on the corresponding wire is connected through and the appropriate LED is illuminated. The upper LED N is illuminated for NPN sensors and the lower LED P for PNP sensors. Do not connect a T-piece to the M socket. The existing M plug-in connectors are wired in such a manner that the PNP sensor can be connected to pin and the NPN sensor to pin. The distributor has eight channels and m of cable. Other versions are also available. Pin assignment M Pin Function Pin Function Output Wire colour Wire socket size PNP NPN white 0. mm PNP NPN green 0. mm PNP NPN yellow 0. mm PNP NPN grey 0. mm PNP NPN pink 0. mm 6 PNP NPN 6 red 0. mm 7 PNP NPN 7 black 0. mm 8 PNP NPN 8 violet 0. mm all V DC brown 0.7 mm all 0 V DC blue 0.7 mm all PE green/yellow 0.7 mm M sockets Pin = + V DC Pin = NPN input Pin = 0 V DC Pin = PNP input Pin = PE V DC ±0% Operation temperature C Storage temperature C Ingress protection class IP68 PUR cable m Max. no-load current for -wire NPN sensors ma DC (schematic) NPN Sensor Cable + V DC SAI-8-F P NPN-PNP M PNP Sensor.8

39 M wall bushing Wall bushing SAI-8- P M SL 60 9, 6, 07 9, 7 SAI-8- P M SL -pole SAI-8- P M SL Note V DC 0 V DC...0 V DC Max. current-carrying capacity per I/O signal A Max. current-carrying capacity per channel A Max. total current 0 A Pollution severity Ingress protection class IP 6 Ambient temperature range -0 C...90 C Housing material Pocan Contact carrier PT (UL 9 V0) ase material of contacts CuZn, pre-nickeled & gold-plated Threaded bush Housing colour grey, RAL 70 Flammability class to UL9 V-0 blue red Clamping range of hood version 0.08 mm... mm Cable carrier compatibility (fixed cable connection) 6 7. With dual power supply x 8 = 6 A total current Clamping range for screw-connection: max.. mm 8-way 6.9

40 M wall bushing Overview Distributors for system cabling On-site distribution is becoming more important. For example, in some places the IP 0 I/O module has to be mounted in housings directly on the machine. This is where a simplified form of wiring is essential. Weidmüller now offers two simple solutions A distributor equipped at the rear with a standardised ribbon cable connector, which is compatible with the Weidmüller PLC system interface. Weidmüller also offers a unique solution for feeding bus cables through panels that can be plugged in from both sides. Advantages Sensors and actuators can be plugged in from outside Through-panel version can be mounted in cut-outs in steel panels Standardised ribbon cable connector inside Plus: M through-panel feed that can be plugged in from both sides Drilling template.0

41 M wall bushing Advantages of system cabling Fast Time-saving installation Reduces commissioning and troubleshooting times On-site wiring cuts wiring costs Contact assignment Male connector X M socket Male connector X... 8 Pin U Pin U Pin PE Male connector X U - PE U + M socket Safe Reduces installation errors Using system cables instead of individual wires improves clarity in control cabinets Direct marking corresponding to the PLC Variability Contact assignment Male connector X M socket Male connector X Pin Pin Pin Pin Pin 6 Pin 6 7 Pin 7 8 Pin 8 8 Pin 9 8 Pin 0 Male connector X Additional I/O modules available Cable length options Easy replacement of I/O interfaces provides flexibility Outputs Inputs Mounting conditions Mounting surface Surface temperature Ingress protection class Fixings Note: 0 0 V (DC) max. A per channel / max. 8 A in total max. A in total sheet steel, flat, min.. mm thick, or panels with at least equivalent stability, max. 6 mm thick max. 0 C IP67/IP68 only in conjunction with control cabinets with equivalent class of protection screws + washers + nuts / torque: 0.8 Nm Connect the male connector. (X) when using actuators SAI-8- P M F

42 Solutions to customer specification Pre-assembled hood version In some instances it is helpful to order the hoods preassembled. SAI distributor with pre-assembled hood - Colour-coded cable Pre-assembled hood Colour-coded cable -pole Type Length Order No. 8-channel SAI-8-MF P PUR M m SAI-8-MF P PUR 0M 0 m pole Type Length Order No. -channel SAI--MF P PUR M m SAI--MF P PUR 0M 0 m channel SAI-8-MF P PUR M m SAI-8-MF P PUR 0M 0 m channel, without initiator LED SAI-8-MF P PUR M OL m pole Type Length Order No. SAI-/6/8-MHF P PUR M m SAI-/6/8-MHF P PUR 6M 6 m SAI-/6/8-MHF P PUR 9M 9 m SAI-/6/8-MHF P PURM m 7900 SAI-/6/8-MHF P PUR0M 0 m SAI-/6/8-MHF P PUR8M 8 m SAI-/6/8-MHF P PURM m 7900 Matching base module SAI--M-PMUT SAI-6-M-PMUT SAI-8-M-PMUT Pre-assembled hood -pole Type Length Order No. SAI-/6/8-MHF P PUR M m SAI-/6/8-MHF P PUR 6M 6 m SAI-/6/8-MHF P PUR 9M 9 m SAI-/6/8-MHF P PURM m SAI-/6/8-MHF P PUR6M 6 m SAI-/6/8-MHF P PUR0M 0 m SAI-/6/8-MHF P PUR8M 8 m SAI-/6/8-MHF P PURM m SAI-/6/8-MHF P PUR0M 0 m SAI-/6/8-MHF P PUR0M 0 m SAI-/6/8-MHF P PURM m Matching base module SAI--M-PMUT SAI-6-M-PMUT SAI-8-M-PMUT

43 .

44 M8 distributors Overview Fixed cable version Compact dimensions, readily accessible M8 connections, eye-catching design The unconventional design of this generation of SAI M8 distributors catches the eye immediately. Their shape is helpful because in this patented design the sockets are no longer arranged in simple rows. Instead, some are on bevelled surfaces. That considerably improves the accessibility of the screw connections for the sensor and actuator cables. Ease of use, compact dimensions and the eye-catching design are the obvious advantages of this M8 generation. The following variations are available: Hood version SAI M8 distributor with removable connection hood; the bus cable can be connected either vertically or horizontally SAI M8 distributor with permanently attached, pre-assembled bus cable, or 0 m long; this version is particularly slim and is therefore ideal for mounting in confined spaces SAI M8 distributor with metal-plated M thread M version.

45 M8 distributors SAI-M8-Line M8 distributor with M outlet The new slimline SAI-M8-Line from Weidmüller SAI-M8-Line, a single-row distributor with M8 connection. One particular highlight of the M8-Line series is the version with M8 sockets which provides maximum connection options in minimum space. oth distributor series are useful in the design of compact machines and installations because they are easily accommodated on handling systems or robots. Extra-narrow M8 distributor for confined spaces M8 distributor line / fixed-cable version Single-row M8 distributors are the smallest sensor-actuator modules currently available with this thread size and it is precisely their size that is decisive for applications. Therefore, this form has become very popular. It is important to maintain the widest possible range of options. The SAI-M8-Line products can provide many interesting solutions: - and 6-channel modules with 8-pole M bus connection 8- and 0-channel modules with -pole bus connection -, 6-, 8-, 0- and -channel distributors with fixed cable connection, the -, 6- and 8-channel modules also with poles It is important to note that the distributors can be labelled with the same markers as the Weidmüller mm modular terminals. Therefore, no new tags had to be introduced. The modules can also be mounted sideways and are completely encapsulated. Consequently, Weidmüller SAI distributors represent stability, robustness, flexibility and compactness in one unit..

46 M8 distributors Hood / Fixed cable version SAI-/8-M SAI-/8-F Hood version Fixed cable version O. 8 O. 8. SAI-/8-M SAI-/8-F -pole Cable length m (with fixed cable version) SAI--M P M SAI--F P M8 PUR M SAI-8-M P M SAI-8-F P M8 PUR M Cable length 0 m (with fixed cable version) SAI--F P M8 PUR 0M SAI-8-F P M8 PUR 0M pole Cable length m (with fixed cable version) SAI--M P M SAI--F P M8 PUR M SAI-8-M P M SAI-8-F P M8 PUR M Cable length 0 m (with fixed cable version) SAI--F P M8 PUR 0M SAI-8-F P M8 PUR 0M Note.0 V DC 0 V 0 V DC br (+) bl ( ) Max. current carrying capacity per input/output signal Max. current carrying capacity per slot Max. total current A A 8 A sock sock wh gr/pi Pollution severity Ingress protection class IP 68 sock sock gn re/bl Ambient temperature range -0 C 80 C Housing material Pocan Contact carrier PT UL 9 V0 ase material of contacts CuZn, pre-nickeled and gold-plated Threaded bush Housing colour grey, RAL 70 Flammability class UL 9 V-0 Clamping range of hood version 0.08 mm mm Dragline compatible Yes (fixed cable connection) sock sock sock sock6 sock7 sock8 8-way -way sock sock sock sock6 sock7 sock8 ye wh/gn gr br/gn pi wh/ye re ye/br bk wh/gr vi gr/br -way 8-way.6

47 M8 distributors with M/M6 outlet SAI-/8-M SAI-8-S with M outlet with M6 outlet M8x0.7 O M6x0.7 O O. SAI-/8-M SAI-8-S -pole SAI-8-M6 P M channel -pole SAI--M P M SAI-8-M P M channel Note.0 V DC 0 V 0 V DC J L C M Max. current carrying capacity per input/output signal A Max. current carrying capacity per slot A Max. total current 8 A Pollution severity Ingress protection class IP 68 Ambient temperature range -0 C 90 C sock sock sock sock sock F G H Housing material Pocan Contact carrier PT UL 9 V0 ase material of contacts CuZn, pre-nickeled and gold-plated Threaded bush Housing colour grey, RAL 70 Flammability class UL 9 V-0 Clamping range of hood version Dragline compatible (fixed cable connection) sock sock sock sock6 sock7 sock8 8-way -way sock sock sock6 sock7 sock8 K A D E.7

48 M8 distributors Line SAI-/6-S SAI-8/0-S with M outlet with M outlet 7 O. R L R A R L R A Ø pole -pole without LED 0 channel 0 channel SAI-/6-S SAI--S P M8 L SAI-6-S P M8 L SAI-6-S P M8 L OL SAI-8/0-S SAI-8-S P M8 L SAI-0-S P M8 L Note.0 V DC 0 V 0 V DC Max. current carrying capacity per input/output signal A Max. current carrying capacity per slot A Max. total current 6 A Pollution severity Ingress protection class IP 68 Ambient temperature range - C 80 C Housing material Pocan Contact carrier PT UL 9 V0 ase material of contacts CuZn, pre-nickeled and gold-plated Threaded bush Housing colour grey, RAL 70 Flammability class UL 9 V-0 Clamping range of hood version Dragline compatible Yes (fixed cable connection) k 7 sock sock sock sock sock sock6 LED-GN 8x LED-YE 8xk 9 (+) 7 ( ) 6 8 -way 6-way sock0 sock9 sock8 sock7 sock6 sock sock sock sock sock 8/0 x LED ye LED gn k /0xk9 (-) (+) 8-way 0-way E.8

49 M8 distributors Line / Fixed cable version 7 R.. A L R.8. O A L R SAI-/6/8/0/-L -pole SAI-/6/8/0/-L -pole Cable length m (with fixed cable version) SAI--F P M8 L M SAI--F P M8 L M SAI-6-F P M8 L M SAI-6-F P M8 L M SAI-8-F P M8 L M SAI-8-F P M8 L M channel SAI-0-F P M8 L M channel SAI--F P M8 L M Cable length 0 m (with fixed cable version) SAI--F P M8 L 0M SAI--F P M8 L 0M SAI-6-F P M8 L 0M SAI-6-F P M8 L 0M SAI-8-F P M8 L 0M SAI-8-F P M8 L 0M channel SAI-0-F P M8 L 0M channel SAI--F P M8 L 0M Note.0 V DC 0 V 0 V DC Max. current carrying capacity per input/output signal A sock wh sock wh LED-GN 6x LED YE br (+) bl ( ) Max. current carrying capacity per slot Max. total current A 6 A sock sock sock wh gr/pi Pollution severity Ingress protection class IP 68 Ambient temperature range - C 80 C Housing material Pocan Contact carrier PT UL 9 V0 sock sock sock ye pi -way sock sock sock ye pi sock sock gn re/bl ye wh/gn ase material of contacts CuZn, pre-nickeled and gold-plated Threaded bush Housing colour grey, RAL 70 Flammability class UL 9 V-0 Clamping range of hood version Dragline compatible Yes (fixed cable connection) sock6 sock7 sock8 sock9 re bk gr/pi 8-way 6-way sock6 sock7 sock8 sock9 re gr/pi re/bl wh/gn sock sock sock6 gr br/gn pi wh/ye re ye/br -way 6-way sock0 re/bl 0-way sock0 sock7 bk wh/gr sock sock wh/ye ye/br -way sock8 vi gr/br 8-way.9

50 M distributors Overview M-Line with M outlet The Weidmüller SAI-M distributors are currently the smallest SAI distributors in the world Whether mobile phones or computers as the functionality increases so the size of the components decreases! Today, machine designers face the same problem. Space is at a premium here as well, even in large machines, particularly where the sensor components are located. In the past the M8 distributor solved these problems. However, these units are now considered to be too large. The first move was to make the sensors smaller. Then it was the turn of the cables and distributors. These extremely small units are surprisingly easy to handle. M plug-in connectors have three or four poles and are thus equivalent to M8 plug-in connectors. Fixed cable version ut in contrast to the M8 plug-in connectors, the different pole numbers here are compatible with each other. The advantage is obvious: -pole units which are required, for example, for antivalent sensors can now be plugged into one and the same distributor with standard NOC applications. In the M8 system special adapters are required. esides their actual size, in some applications module weight is critical too. For example, the speed of a handling machine is influenced by the weight of the moving parts. Here again, the M system offers outstanding advantages, with its almost unrivalled small size and light weight. There is no version for custom bus cable assembly for this SAI distributor, which is delivered with a plug-in connection and a fixed cable connection. A compact -pole M plug-in connector has been developed as a plug-in connection specifically for this distributor. M-Line with M6 outlet This ratio of surface area to number of connections is reminiscent of the computer industry. The M6 bus connection is also integrated in the module as an option, so the SAI M can be used as a combined SAI system as well. A Y-configuration is possible in conjunction with the M6 splitter. The fixed cable version is particularly suitable for standard applications where the distributor is permanently installed and the electrical installation does not have to be disconnected after installation. The bus cable is reduced in cross-section to save weight here too..0

51 M distributors M distributors Quality comes in little packages This is the motto with which Weidmüller developed its distributor with M plug-in connectors. The outstanding feature of these connectors is their size. Attention has also been given to stability and good conductivity. For a comparison of sizes, take a look at the photos on the left. These products are ideal for handling machines where light weight and small size are vital. Comparing the sizes Marking Each channel is marked with the channel number. Each initiator LED can be exactly allocated with the letters A and. In addition, the distributor and every channel can be marked. M M8 M M M8 M.

52 M distributors Line SAI-/8-F SAI-/8-S Fixed cable version with M outlet M A A A A A A 69 A A A 9. -pole Cable length m (with fixed cable version) Cable length 0 m (with fixed cable version) -pole Cable length m (with fixed cable version) Cable length 0 m (with fixed cable version) SAI-/8-F SAI--F P M LM SAI-8-F P M LM SAI--F P M L0M SAI-8-F P M L0M SAI--F P M LM SAI-8-F P M LM SAI--F P M L0M SAI-8-F P M L0M SAI-/8-S SAI-8-S P M SAI--S P M Note.0 V DC 0 V 0 V Max. current carrying capacity per input/output signal A Max. current carrying capacity per slot A Max. total current A Pollution severity Ingress protection class IP 67 Ambient temperature range - C 80 C Housing material PA 6 GF Contact carrier ase material of contacts Au (gold) Threaded bush Housing colour grey, RAL 70 Flammability class UL 9 V-0 Clamping range of hood version Dragline compatible Yes (fixed cable connection) sock sock sock sock sock sock6 wh gn ye gr pi re -way sock sock sock sock LED gn k 7 8 x LED ge 8 x k way sock7 bk sock8 vi 8-way.

53 M distributors Line SAI-/8-S6 with M6 outlet A A A A A A A A A 8 -pole -pole Note 0 channel 0 channel SAI-/8-S6 SAI--S6 P M SAI-8-S6 P M SAI--S6 P M SAI-8-S6/9P P M , and with M6 / -pole with M6 / 9-pole.0 V DC 0 V 0 V LED-GN Max. current carrying capacity per input/output signal Max. current carrying capacity per slot Max. total current A A A sock k 7 8 x LED-YE 8 x k 9 Pollution severity Ingress protection class IP 67 Ambient temperature range - C 80 C sock Housing material Contact carrier PA 6 GF sock ase material of contacts Au (gold) Threaded bush Housing colour grey, RAL 70 sock -way Flammability class UL 9 V-0 Clamping range of hood version sock Dragline compatible (fixed cable connection) sock6 sock7 sock8 8-way.