ADDITIONAL CONDUCTED MEASUREMENTS BOARD DESCRIPTION

Transcription

1 AMIS-530XX Frequency Agile Transceiver ETSI Test Report Contents Board Description Radiated Measurements Additional Conducted Measurements TECHNICAL NOTE ADDITIONAL CONDUCTED MEASUREMENTS BOARD DESCRIPTION Schematics Assembly Plan NOTE: The test certification was successfully completed on the AMIS I/A (AMIS p/n ). Similar results are expected from customer certification of boards using the AMIS (AMIS p/n ) or AMIS (AMIS p/n ) as the silicon process, RF circuits and packaging are all the same. Figure 1. Schematic Semiconductor Components Industries, LLC, 2013 July, 2013 Rev. 3 1 Publication Order Number: TND339/D

2 Figure 2. 2

3 Figure 3. 3

4 RADIATED MEASUREMENTS The measurements have been performed by: mikes testingpartners GmbH Ohmstra e Strasskirchen, Germany 4

5 5

6 6

7 7

8 8

9 9

10 ADDITIONAL CONDUCTED MEASUREMENTS Additional Conducted Measurements The modulation bandwidth according to clause 8.7 of EN , part 1, was measured at full output power (Register 18 at 7Fh) with PRBS FSK modulation with 19.2 kbit/s and a frequency deviation of 19.2 kbit/s. Figure 4. Output Spectrum of the Modulation Bandwidth Measurement The measured modulation bandwidth is 186 khz. The reference design can therefore be used in all the proposed frequency bands g1 ( MHz), g2 ( MHz) and g4 ( MHz). Maximum Usable Sensitivity The sensitivity according to clause 9.1 of EN was measured with a data rate of 19.2 kbit/s and a frequency deviation of 19.2 khz. The sensitivity for a BER < 10 2 is 98 dbm. Receiver Blocking The receiver blocking according to clause 9.4 of EN was measured with a data rate of 19.2 kbit/s and a frequency deviation of 19.2 khz. The level of the signal was increased to 95 dbm, which is 3 db above the sensitivity threshold. Table 1 has the maximum interferer levels for BER < 10 2 and a comparison to the required levels for class 2 receivers in EN Table 1. INTERFERER LEVELS COMPARISON Frequency Offset Max. Interferer Level Measured Max. Interferer Level Required in EN Margin +2 MHz 53 dbm 69 dbm 16 db 2 MHz 53 dbm 69 dbm 16 db +10 MHz 31 dbm 44 dbm 13 db 10 MHz 27 dbm 44 dbm 17 db 10

11 Table 2. BOARD BILL OF MATERIALS ResDef Component Name Value Vendor Vendor Ordering Number Remarks N1 AMIS53050 ON/CompoTEK XTD / P X1 AMIS_25POL 3 Connectors 100mil Pitch C1 C0402 5p6 Darfon/CompoTEK C1005NPO569BGT C2 C p Darfon/CompoTEK C1005NPO151JGT C3 C0402 3p9 Darfon/CompoTEK C1005NPO399BGT C4 C0402 3p9 Darfon/CompoTEK C1005NPO399BGT C5 C p Darfon/CompoTEK C1005NPO151JGT C6 C n Darfon/CompoTEK C1005X5R104KET C7 C0402 1n0 Darfon/CompoTEK C1005X7R102KGT C8 C p Darfon/CompoTEK C1005NPO151JGT C9 C0402 1n0 Darfon/CompoTEK C1005X7R102KGT C10 C n Darfon/CompoTEK C1005X5R104KET C12 C p Darfon/CompoTEK C1005NPO151JGT C13 C0402 1n0 Darfon/CompoTEK C1005X7R102KGT C14 C n Darfon/CompoTEK C1005X5R104KET C15 C p Darfon/CompoTEK C1005NPO151JGT C16 C0402 0p5 Darfon/CompoTEK C1005NPO508BGT C17 C0402 3p3 Darfon/CompoTEK C1005NPO339BGT C18 C0402 1n0 Darfon/CompoTEK C1005X7R102KGT C19 C n Darfon/CompoTEK C1005X5R104KET C20 C0402 4p7 Darfon/CompoTEK C1005NPO479BGT C21 C p Darfon/CompoTEK C1005NPO330JGT C22 C p Darfon/CompoTEK C1005NPO331JGT C23 C n Darfon/CompoTEK C1005X5R473KET C24 C p Darfon/CompoTEK C1005NPO330JGT C25 C p Darfon/CompoTEK C1005NPO330JGT C26 C p Darfon/CompoTEK C1005NPO330JGT C27 C p Darfon/CompoTEK C1005NPO330JGT C28 C p Darfon/CompoTEK C1005NPO330JGT C29 C p Darfon/CompoTEK C1005NPO330JGT C30 C p Darfon/CompoTEK C1005NPO330JGT C31 C p Darfon/CompoTEK C1005NPO330JGT C32 C p Darfon/CompoTEK C1005NPO330JGT C33 C p Darfon/CompoTEK C1005NPO330JGT C34 C p Darfon/CompoTEK C1005NPO330JGT C35 C p Darfon/CompoTEK C1005NPO330JGT C36 C p Darfon/CompoTEK C1005NPO330JGT C37 C p Darfon/CompoTEK C1005NPO330JGT C38 C p Darfon/CompoTEK C1005NPO330JGT C39 C p Darfon/CompoTEK C1005NPO330JGT C40 C p Darfon/CompoTEK C1005NPO330JGT C41 C0402 1p8 Darfon/CompoTEK C1005NPO189BGT 11

12 Table 2. BOARD BILL OF MATERIALS (continued) ResDef Component Name Value Vendor Vendor Ordering Number Remarks C42 C0402 1p8 Darfon/CompoTEK C1005NPO189BGT C43 C0402 5p6 Darfon/CompoTEK C1005NPO569CGT L1 DARFON_L n Darfon/CompoTEK HI160818NJT L2 DARFON_L0402 8n2 Darfon/CompoTEK HI10058N2NJT L3 CHILISIN CS0402 9n0 Chilisin/CompoTEK CS0402 9N0J S L4 CHILISIN CS0402 4n7 Chilisin/CompoTEK CS0402 4N7J S L5 CHILISIN CS n Chilisin/CompoTEK CS0402 R10J S L7 CHILISIN CS n Chilisin/CompoTEK CS NJ S R1 R k KOA/CompoTEK RK73H1ETTP6802F R2 R k KOA/CompoTEK RK73H1ETTP3302F R5 R0402 1k8 KOA/CompoTEK RK73H1ETTP1801F R6 R0402 0R0 KOA/CompoTEK RK73Z1ETTP J1 JUMP2 X2 JUMP0402 Jumper Formed by re XTAL1 Crystal 24 MHz Aker/CompoTEK CTA /2 X3 SMA_Connector Jyebao/CompoTEK SMA C11 TANTAL_A 100 /4 V AVX TLJA107M004R0500 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC s product/patent coverage may be accessed at Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Typical parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customer s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado USA Phone: or Toll Free USA/Canada Fax: or Toll Free USA/Canada orderlit@onsemi.com N. American Technical Support: Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: Japan Customer Focus Center Phone: ON Semiconductor Website: Order Literature: For additional information, please contact your local Sales Representative TND339/D