MOONRING MULTIPLES INSTALLATION INSTRUCTIONS MOONRING MULTISTAK TM STACKED CANOPY. A nd Avenue, Unit 1 Oakland,

Size: px

Start display at page:

Download "MOONRING MULTIPLES INSTALLATION INSTRUCTIONS MOONRING MULTISTAK TM STACKED CANOPY. A nd Avenue, Unit 1 Oakland,"

Damian Lloyd
5 years ago
Views:

1 INSTALLATION INSTRUCTIONS MOONRING MULTIPLES MOONRING MULTISTAK TM STACKED CANOPY A nd Avenue, Unit 1 Oakland, CA P E TalkToUs@alwusa.com W alwusa.com

2 MR-MultiStak - Safety & Warnings! 1. Read all instructions. 2. Install in accordance with national and local electrical code regulations. 3. This product is intended to be installed and serviced by a qualified, licensed electrician. 4. Only install with a compatible Class 2 LED Driver. This product has not been evaluated for use when connected to an LED driver that does not comply with Class 2 voltage and energy limited supplies. 5. Do not install in wet locations. For dry and damp use only. 6. Turn off electrical power before installing or servicing fixture in any way. 7. To reduce the risk of fire and overheating, make sure all connections are tight. MR-MultiStak - Attention! 1. Lisez toutes les instructions. 2. Installez conformément à la réglementation du code électrique national et local. 3. Ce produit est destiné à être installé et entretenu par un électricien agréé qualifié. 4. Installez uniquement avec un pilote à DEL de classe 2 compatible. Ce produit n a pas été évalué pour une utilisation lorsqu il est connecté à un pilote de LED qui n est pas conforme aux alimentations de tension et d énergie limitée de classe 2 5. Ne pas installer à l extérieur ou dans des endroits humides. Pour une utilisation en intérieur et sec seulement. 6. Coupez l alimentation électrique avant de évoluer le système d éclairage en aucune façon. 7. Pour réduire le risque d incendie et de surchauffe, assurez-vous que toutes les connexions sont bien serrées. SHOCK HAZARD! May result in serious injury or death. Turn power OFF at circuit breaker prior to installation or servicing. MOONRING MULTISTAK TM Install Guide 2 of IG A.0

3 Table of Contents Luminaire Overview Diagram 4 4 Included Parts Parts (by others) Tools Required Quick Specs Canopy Overview 5 Installation 4 x4 Square J-Box 4 x4 Octagonal J-Box Remote Driver and Drywall Canopy Installation 6 7 Suspend Rings 8 Wiring 9 Lens Wiring Diagrams Traditional On/Off V Dimming 11 DMX 11 DALI 11 Lutron LDE V Tunable 12 Troubleshooting 13 MOONRING MULTISTAK TM Install Guide 3 of IG A.0

4 Luminaire Overview 7" 1 5 8" Included Parts MR Fixtures MR Lenses Ceiling Suspension Plate MultiStak Cover Plate Hardware Parts (by others) 8X #10 screws (for structure) Wire nuts Tools Required Screwdriver Drill Philips bit Wire strippers Quick Specs Input Voltage / Frequency: See product label Rated Current: See engineering drawing Ambient Temperature: F ( C) Environment: Dry and damp locations MOONRING MULTISTAK TM Install Guide 4 of IG A.0

5 Canopy Overview mounting screws (by others) MOONRING MULTISTAK TM Install Guide 5 of IG A.0

6 Installation: 4x4 Square Junction Box Installation: 4x4 Octagonal Junction Box 4" 4" 3 1 2" 4" 1A Install blocking for structure and JBOX Install blocking to frame J-box in a 4 x 4 square. 1B Install blocking for structure and JBOX Install blocking to frame J-box in a 3 1/2 x 4 rectangle. 4" 4" 4" 3 1 2" 1/4 gap between main structure members and J-Box 2A Mount JBOX 2B Mount JBOX Installation: Remote Driver and Drywall 5 5 8" 3 Install Remote Driver J-Box Install remote driver J-Box(es) in an accessible/ serviceable location. Run low voltage wire from Remote Driver J-Box to Canopy J-Box in accordance with local/ state/federal regulations. 4 Install drywall Install drywall with circular, 5 5 /8 diameter cutout around J-box. MOONRING MULTISTAK TM Install Guide 6 of IG A.0

7 Installation: Canopy Installation 5 Attach suspension plate to J-Box 8 Install MOONRING MULTISTAK TM Attach canopy suspension plate to J-Box on ceiling. Suspension plate must sit flush on ceiling surface. Install MOONRING MULTISTAK to canopy suspension plate using provided 1/4-20 screws. 6 Fasten suspension plate to structure Fasten canopy suspension plate to structure using 8X #10 screws (min. 2 length). 7 Fasten suspension plate to structure Ensure screws properly penetrate blocking for proper load bearing. MOONRING MULTISTAK TM Install Guide 7 of IG A.0

8 Installation: Suspend Rings 9 Raise 1st fixture to cables 12 Raise 3rd firxture to cables Raise first fixture to corresponding cables. See submittal drawing to match correct cables to cable grippers. Raise third fixture to corresponding cables. See submittal drawing to match correct cables to cable grippers. Insert cable into cable grippers as shown in step Insert suspension cable and adjust Insert suspension cable into cable gripper and adjust length as necessary. 13 Trim excess suspension cable With rings suspended at proper height, cut excess suspension cable. 11 Raise 2nd fixture to cables Raise second fixture to corresponding cables. See submittal drawing to match correct cables to cable grippers. Insert cable into cable grippers as shown in step 10. MOONRING MULTISTAK TM Install Guide 8 of IG A.0

9 Installation: Wiring 14 Make wiring connections Bring cables from rings through cover plate. Pull wire to desired length and tie knot above plate. Ensure adequate cable length to reach canopy (lift canopy cover plate to verify). If cable is too long, re-tie knot. Once cable length is correct, trim cable and make wiring connections using wire nuts. See submittal drawings and diagrams on pg. 11 for complete wiring instruction. 15 Install cover plate Push wiring connections into J-Box and canopy. Lift cover plate to stack and secure using provided screw. MOONRING MULTISTAK TM Install Guide 9 of IG A.0

10 Installation: Lens 16A Install Downlight Lenses Carefully angle/snap lenses into fixture, as shown. Note: because lenses are not adhered to fixture, fixture may only be mounted at moderate angles up to 20 degrees. 16B Install Downlight Lenses Ensure lenses overlap, as shown. 17 Turn Power On Turn breaker ON and ensure that fixture operates as intended and that there are no loose connections. MOONRING MULTISTAK TM Install Guide 10 of IG A.0

11 Wiring Diagrams Traditional On/Off DC Driver 1 LED + Brown L N AC 50/60Hz Line Voltage (Hot) Line Voltage (Neutral) Ground Green Remote LED Driver J-Box Driver 1 LED - Blue Driver 2 LED + Yellow Driver 2 LED - Orange 0-10V Dimming DC L N AC 50/60Hz DIM- Line Voltage (Hot) Line Voltage (Neutral) Ground 0-10VDC (Dim-) Green Grey Remote LED Driver J-Box Driver 1 LED + Brown Driver 1 LED - Blue Driver 2 LED + Yellow Driver 2 LED - Orange DIM+ 0-10VDC (Dim+) Purple DMX L Line Voltage (Hot) N AC 50/60Hz Line Voltage (Neutral) Ground Green DC Driver 1 LED + Brown DMX In Shield DMX in - DMX in + DMX in shield DMX in - DMX in + Clear Red Remote LED Driver/Decoder J-Box Driver 1 LED - Blue Driver 2 LED + Yellow Driver 2 LED - Orange DMX Out Shield DMX out shield Clear DMX out - DMX out - DMX out + DMX out + DALI L N AC 50/60Hz DATA + Line Voltage (Hot) Line Voltage (Neutral) Ground Data + Green Purple Remote LED Driver/Decoder J-Box DC Driver 1 LED + Brown Driver 1 LED - Blue Driver 2 LED + Yellow Driver 2 LED - Orange DATA - Data - Grey Lutron LDE L N AC 50/60Hz E1 Line Voltage (Hot) Line Voltage (Neutral) Ground E1 Green Purple Remote LED Driver J-Box DC Driver 1 LED + Brown Driver 1 LED - Blue Driver 2 LED + Yellow Driver 2 LED - Orange E2 E2 Grey MOONRING MULTISTAK TM Install Guide 11 of IG A.0

12 Wiring Diagrams 0-10V Tunable L N AC 50/60Hz DIM- Line Voltage (Hot) Line Voltage (Neutral) Ground 0-10VDC (Dim-) Green Grey Remote LED Driver/Decoder J-Box DC Driver 1 LED + Brown Driver 1 LED - Blue Driver 2 LED + Yellow Driver 2 LED - Orange DIM+ 0-10VDC (Dim+) Purple TUNE- 0-10VDC (Tune-) Yellow TUNE+ 0-10VDC (Tune+) Brown MOONRING MULTISTAK TM Install Guide 12 of IG A.0

13 Troubleshooting Only a certified electrician can service and troubleshoot product field issues. Always turn main power off before servicing fixture. Full Fixture does not illuminate Ensure fixture is wired correctly and power is on. Check that circuit breaker is on and not off or tripped. Internal LED driver may be defective. Ensure no wires are pinched between parts after joining sections or re-attaching end caps. Full fixture is flickering 0-10V, DMX, and DALI Dimming Models: Ensure polarity is correct for DATA + and - connections. Swapping DATA + and - connections can cause flickering. TRIAC Dimming Models: Ensure a compatible TRIAC Forward Phase dimmer is connected to fixture. Call tech support for further information. Possible loose DATA + and - connections from fixture to 0-10V, DMX, or DALI control. Possible loose low voltage DC + or - connection from driver to LED. Call customer support. Fixture section(s) do not illuminate Possible loose low voltage DC + or - connection between LED boards or from LED driver to LED boards. Some fixtures contain multiple LED drivers. In this case, it s possible one of the drivers is defective, which will cause the LED connected to the driver not to illuminate. Call tech support. Ensure no wires are pinched between parts after joining sections or re-attaching end caps. Fixture section(s) are flickering Possible loose low voltage DC + or - connection between LED boards. Fixture does not dim 0-10V, DMX, and DALI Dimming Models: Ensure polarity is correct for DATA + and - connections. Swapping DATA + and - connections can cause flickering. TRIAC Dimming Models: Ensure a compatible TRIAC Forward Phase dimmer is connected to fixture. Call tech support for further information. Possible loose DATA + and - connections from fixture to 0-10V, DMX, or DALI control. MOONRING MULTISTAK TM Install Guide 13 of IG A.0

Lumination TM LED Luminaire LUS Series

GE Lighting Installation Guide Lumination TM LED Luminaire LUS Series BEFORE YOU BEGIN Read these instructions completely and carefully. RISK OF ELECTRIC SHOCK Turn power off before inspection, installation