WizFi250 Datasheet. Introduction. Features. WizFi250 Datasheet v English. Datasheet History

Transcription

1 2015/02/06 13:12 1/18 v English Datasheet History Version Date Description V Official Release Fixed some mistyping V Add JTAG_TCK (Pin Number 54) ntroduction WizFi250 is a small size wireless module for the highest level of integration, featuring b/g and n. t includes a 2.4 GHz WLAN CMOS power amplifier (PA) that meets the output power requirements of most handheld systems. Along with the integrated power amplifier, the WizFi250 also includes integrated transmit and receive baluns, further reducing the overall solution cost. The small size and low profile physical design eases enabling high performance wireless connectivity without space constraint in system designs. Hardware WAP acceleration engine, AES, TKP, WPA and WPA2 are supported to provide your network with the latest security requirements. For software and driver development, WZnet provides extensive technical documents and reference software codes for system integration. 2013/08/28 09:43 ssekim Features Single band 2.4GHz EEE b/g/n ntegrated RF power amplifier Supports wireless data rates up to 65Mbit/s 1MB Flash Memory, 128KB SRAM, 1MB Serial Flash Supports per packet Rx Antenna diversity Low power consumption & excellent power management performance to extend battery life. Small size, suitable for low volume system integration. Easy integration into mobile and handheld devices flexible system configuration GHz two SKUs for worldwide market. Lead Free design supporting Green design requirements, RoHS Compliance. Device Package : mm (17 20 mm) Serial nterface : UART, SP Powerful Web server provides Soft AP Sufficient memory retention Wi-Fi Security (WEP, WPA/WPA2PSK) L2 Switching OTA(Over The Air F/W Upgrading) -

2 products:wizfi250:wizfi250ds:start /08/28 09:42 ssekim Block diagram The WizFi250 module is designed based on WiFi block and MCU block. t supports generic SP, UART interface to connect WLAN to the host processor. A simplified block diagram of the WizFi250 module is depicted in the Fig. below. 2013/08/28 09:47 ssekim Pin description Pin map Printed on 2015/02/06 13:12

3 2015/02/06 13:12 3/18 Pin description Pin Number Pin Define 1 2 VBAT_WL 3 VBAT_WL 4 5 VDDO_3V3_WL Type Description - Groud Battery supply input Battery supply input - Ground Digital supply. - Ground -

4 products:wizfi250:wizfi250ds:start SP_MSO SP_SCK SP_MOS SP_SS VDD_3V3 VDD_3V3-29 UART2_RTS 30 UART2_CTS UART2_RXD UART2_TXD RESET VBAT GPO1 BOOT FUTON GPO5 GPO6 GPO7 GPO8 GPO9 Wi-Fi_STATUS MODE_STATUS SP_Data_Ready(GPO14) O 51 JTAG_TRST Ground Ground SP Master n Slave Out SP Clock SP Master Out Slave n SP Slave Select Ground Power supply for and the internal regulator Power supply for and the internal regulator Ground Active-low request-to-send signal for UART2 interface (Not Used) Active-low clear-to-send signal for UART2 interface (Not Used) Serial data input for UART2 interface (Not Used) Serial data output for UART2 interface (Not Used) RESET pin (Active Low) Ground Power supply when VDD_3V3 is not present. Ground GPO1 pin BOOT MODE pin (Active low) FUTON pin (Active Low) GPO5 pin GPO6 pin GPO7 pin GPO8 pin GPO9 pin Wi-Fi Status pin MODE Status pin n SP Mode, t is used to SP_Data Ready Pin For normal operation, if JTAG is not used, this pin can be left unconnected () Printed on 2015/02/06 13:12

5 2015/02/06 13:12 5/18 52 JTAG_TDO 53 JTAG_TD 54 JTAG_TMS 55 JTAG_TCK UART1_RTS 62 UART1_CTS 63 UART1_RXD 64 UART1_TXD 65~ /08/28 10:41 ssekim For normal operation, if JTAG is not used, this pin can be left unconnected () For normal operation, if JTAG is not used, this pin can be left unconnected () For normal operation, if JTAG is not used, this pin can be left unconnected () For normal operation, if JTAG is not used, this pin can be left unconnected () - Ground - Ground - Ground - Ground - Active-low request-to-send signal for UART1 interface (Use) Active-low clear-to-send signal for UART1 interface (Use) Serial data input for UART1 interface (Use) O Serial data output for UART1 interface (Use) - Ground Technical specification Absolute maximum rating Supply Power Max +3.6 Volt Storage Temperature - 40 to 85 Celsius Voltage ripple +/- 2% Max Values not exceeding Operating voltage Recommendable operation condition Temperature, humidity The WizFi250 can withstand the operational requirements as listed in the table below. Operating Temperature -20 to 85 Celsius Humidity range Max 95%, Non condensing, relative humidity * The maximum operating ambient temperature can be up to 85. Exposure to absolute-maximum-rated conditions may cause performance degradation and affect device reliability. For the best performance -20 to 75 is recommended. Voltage Power supply for the WizFi250 module will be provided by the host via power pins. -

6 products:wizfi250:wizfi250ds:start Symbol Parameter Min Typ. Max Unit VBAT_WL power supply for WizFi V VDDO_3V3_WL host nterface power supply V VBAT_MCRO backup operating voltage V VDD_3V3 power supply for MCU V Current consumption The WizFi250 on operation output current consumption : WiFi mode Typ. Max. (802.11n) (RMS) Normal mode Not Associated 14 ma 18 ma Normal mode Associated 67 ma 69 ma Associated Normal mode 32 ma 65 ma (EEE Power Save mode) Associated Stop mode 14 ma 17 ma (EEE Power Save mode) Stop mode Not Associated 3 ma 23 ma MCU mode The WizFi250 on TX mode output current consumption : (Typical spec is 25 ; MAX. spec is 70 ) Current Consumption Typ. Max. Tx output dbm on 11b 1M 385 ma 430 ma Tx output 16.5 dbm on 11b 11M 370 ma 410 ma Tx output 15 dbm on 11g 6M 345 ma 380 ma Tx output 13 dbm on 11g 54M 290 ma 320 ma Tx output 14.5 dbm on 11n MCS0 315 ma 350 ma Tx output 12 dbm on 11n MCS7 265 ma 295 ma The WizFi250 on RX mode current consumption : (Typical spec is 25 ; MAX. spec is 70 ) Current Consumption Typ. Max. 11b 1M 120 ma 150 ma 11b 11M 120 ma 150 ma 11g 6M 120 ma 150 ma 11g 54M 120 ma 150 ma 11n MCS0 120 ma 150 ma 11n MCS7 120 ma 150 ma Wireless specifications WizFi250 complies with following features and standards; Features WLAN Standards Description EEE b/g/n Printed on 2015/02/06 13:12

7 2015/02/06 13:12 7/18 Antenna Connecter Port One printed antenna, one U.FL connector for external antenna Frequency Band GHz ~ GHz Number of Sub Channels CH1 to CH14 Modulation DSSS, CCK, OFDM, BPSK, QPSK,16QAM, 64QAM 11b 1, 2, 5.5, 11 (Mbps) Supported data rates 11g 6, 9, 12, 18, 24, 36, 48, 54 (Mbps) 11n HT20 MCS0(6.5Mbps) to HT20 MCS7(65Mbps) Specifications of WiFi s output power, evm, sensitivity The WizFi250 WiFi output power is listed in the table below: Characteristics Typ. Criteria Unit 1M /- 1.5 dbm RF Average Output Power, b CCK Mode 11M /- 1.5 dbm 6M 15 +/- 1.5 dbm RF Average Output Power, g OFDM Mode 54M 13 +/- 1.5 dbm MCS /- 1.5 dbm RF Average Output Power, n OFDM Mode MCS7 12 +/- 1.5 dbm WiFi TX EVM following the EEE spec as listed in the table below: Characteristics EEE Spec Mbps -10 db RF Average Output EVM Mbps -10 Mbps -5 db RF Average Output EVM Mbps -25 MCS0-5 db RF Average Output EVM MCS7-28 db The WizFi250 Wi-Fi sensitivity as listed in the table below: Receiver Characteristics Typ. Max. Unit PER <8%, Rx 1 Mbps dbm PER <8%, Rx 11 Mbps dbm PER <10%, Rx 6 Mbps dbm PER <10%, Rx 54 Mbps dbm PER <10%, Rx MCS dbm PER <10%, Rx MCS dbm 2013/08/28 10:44 ssekim port characteristics WizfFi250 is a small size wireless module. Unless otherwise specified, parameters are given as in the table below. Symbol - Parameter Conditions Min Typ Max Unit

8 products:wizfi250:wizfi250ds:start Standard O input low level voltage -0.3 O FT(1) input low level voltage -0.3 Standard O input high level voltage 0.41*(VDD -2V)+1.3V 0.42*(VDD -2V)+1V VL VH O FT(1) input high level voltage VDD > 2V VDD 2V Vhys lkg RPU RPD CO Standard O Schmitt trigger voltage hysteresis(2) OFT Schmitt trigger voltage hysteresis(2) V V VDD+0.3 V 5.5 V mv 5%VDD(3) mv VSS VN VDD Standard s nput leakage current VN=5V, FT (5) Weak pull-up equivalent resistor VN=VSS 30 (5) Weak pull-down equivalent resistor VN=VDD 30 pin capacitance (4) 0.28*(VDD -2V)+0.8V 0.32*(VDD -2V)+0.75V ± μa kω kω pf 1. FT = Five-volt tolerant. n order to sustain a voltage higher than VDD+0.3 the internal pull-up/pull-down resistors must be disabled. 2. Hysteresis voltage between Schmitt trigger switching levels. Based on characterization, not tested in production. 3. With a minimum of 100 mv. 4. Leakage could be higher than max. if negative current is injected on adjacent pins. 5. Pull-up and pull-down resistors are designed with a true resistance in series with a switchable PMOS/NMOS. The MOS/NMOS contribution to the series resistance is minimum(~10% order). 2013/08/28 13:30 ssekim Dimensions, weight and mounting The following paragraphs provide the requirements for size, weight and mounting of the WizFi250. Dimensions 28 mm (W) x 20 mm (L) x 1.9 mm (H) (+/- 0.1mm) (PCB Antenna, ncluding metal shielding) 17 mm (W) x 20 mm (L) x 1.9 mm (H) (+/- 0.1mm) Printed on 2015/02/06 13:12

9 2015/02/06 13:12 Pin out and pin description Recommend footprint - 9/18

10 products:wizfi250:wizfi250ds:start /08/28 13:45 ssekim Design Guide PCB Antenna Guide Module Location Recommendation To get better antenna performance, the following two module locations are advised. Printed on 2015/02/06 13:12

11 2015/02/06 13:12 11/18 -Location 1: Module is recommended to be on the upper right corner of main board. -Location 2: Module is recommended to be on the upper left corner of main board. Module Layout Guideline - Main board antenna area under module printed antenna should be clear or empty. - No signals, or power traces can be routed in antenna area for each layers of the main board. - Any mental lids, power traces or metal components should be placed far away from the antenna area on the main board. - Keep plane as large as you can on main board. -

12 products:wizfi250:wizfi250ds:start Antenna Simulation Result Ant. on right-up corner Ant. on left-up corner Configuration S11 Gain Printed on 2015/02/06 13:12

13 2015/02/06 13:12 13/18 3D Pattern Antenna Measurement Setup Module is on the upper right corner of main board for performance measurement. -

14 products:wizfi250:wizfi250ds:start Antenna measurement setup as the figure. Antenna Measurement Results Printed on 2015/02/06 13:12

15 2015/02/06 13:12 15/18 Firmware Update - Circuit Guide WizFi250 provides some specific functions according to its firmware. Until now, there is a standard firmware and some customized firmware to specific customers available. t is possible to perform firmware updates. WizFi250 decides its operating mode according to the input value of the BOOT signal. WizFi250 operates in boot mode when the BOOT input value is LOW, otherwise it operates in the standard run mode. WizFi250 communicates with a PC via UART in order to upload another firmware, so you have to connect UART1_RXD and UART1_TXD to the external interface for communicating with PC. Two different schematics for that connection are listed below. Case 1 A simple circuit for updating firmware. f your application MCU has UART communication with WizFi250, there is a possibility that the firmware update with an external PC will fail because of dual use of the one UART interface. n that case WZnet cannot guarantee a completely successful update. Therefore, please monitor the signal of BOOT with your MCU by a GPO. Please stop the UART communication between your MCU and the WizFi250 when the BOOT input value is LOW. After that detection of a LOW BOOT signal you can succeed firmware update. -

16 products:wizfi250:wizfi250ds:start Case 2 This circuit selects the UART communication using some extra hardware. f the BOOT SW is ON(), it is in BOOT Mode, and if the BOOT SW is OFF(3.3V) it is RUN Mode. The UART signal of the WizFi250 is connected to the firmware update UART (PC) when it becomes BOOT Mode, so firmware updates are made possible. The UART signal of the WizFi250 is only connected on your MCU if the BOOT signal is High and WizFi250 goes into the RUN Mode. Printed on 2015/02/06 13:12

17 2015/02/06 13:12 17/ /11/28 17:11 jeongsk Recommend reflow profile The following paragraphs provide the requirements for the size, weight and mounting of the WizFi

18 products:wizfi250:wizfi250ds:start A-B. Temp.: 150~200 ; soak time:60~120sec. C. Peak temp: 235~245. D. Time above 220 : 40~90sec. Suggestion: Optimal cooling rate is <1 /sec. from peak to /08/28 14:32 ssekim WizFi250 Ref. Schematic Ref Schematic 2013/10/04 15:54 jeongsk From: Permanent link: Printed on 2015/02/06 13:12