TracVision R6 & Multi-service Interface Box. User s Guide

Transcription

1 TracVision R6 & Multi-service Interface Box User s Guide

2 Welcome to TracVision R6 TracVision User s Guide R6 Satellite TV Antenna & Interface Box This manual provides detailed instructions on the proper operation, setup, and troubleshooting of the KVH TracVision R6 mobile satellite TV antenna system. For basic operation information, also refer to the Quick Start Guide. For installation instructions, refer to the Installation Guide. Please direct questions, comments, or suggestions to: KVH Industries, Inc. KVH Europe A/S 50 Enterprise Center Kokkedal Industripark 2B Middletown, RI USA 2980 Kokkedal, Denmark Tel: Tel: Fax: Fax: info@kvh.com info@kvh.dk Internet: Internet: If you have any comments regarding this manual, please them to manuals@kvh.com. Your input is greatly appreciated! KVH Part # Rev. A 2006, KVH Industries, Inc., All rights reserved.

3 TracVision, KVH, and DewShield are trademarks of KVH Industries, Inc. DVB (Digital Video Broadcasting) is a registered trademark of the DVB Project. DIRECTV is an official trademark of DIRECTV, Inc. DISH Network is an official trademark of EchoStar Communications Corporation. ExpressVu is a property of Bell ExpressVu, a wholly owned subsidiary of Bell Satellite Services. TiVo is a registered trademark of TiVo Inc., or its subsidiaries.

4 Table of Contents Table of Contents 1 Introduction System Overview How to Use This Manual Operation Receiving Satellite TV Signals Turning On the System Turning Off the System Understanding the Status Screen Switching Satellites System Preferences Turning DewShield On/Off Adjusting the Display Brightness Setting to Defaults Initial Setup Initial Setup DIRECTV Initial Setup DISH Network Initial Setup ExpressVu Initial Setup Manual Mode Resetting the System to Change the Initial Setup Troubleshooting Five Simple Checks System Status Lights Running the Diagnostics Test Viewing System Information Technical Support Product Care i

5 Appendices Index A System Wiring Diagrams

6 Introduction 1 Introduction Contents This section provides a basic overview of the TracVision R6 system and explains how to use this manual. 1.1 System Overview How to Use This Manual

7 Introduction 1.1 System Overview When connected to your satellite TV receiver and television, the TracVision R6 antenna system delivers live satellite TV to your RV or motorcoach even while you re on the move! A basic system is illustrated in Figure 1-1. Detailed system wiring diagrams are provided in Appendix A on page 53. Figure 1-1 Basic TracVision R6 System Diagram TracVision Antenna Interface Box Vehicle Power 12 VDC Satellite Receiver TV System Components The TracVision R6 includes the following components: Antenna Using integrated DVB and GPS technology, the low-profile (12.5" high) antenna quickly acquires the correct satellite, switches between satellites, and sends TV signals to the interface box. Internal gyros allow the antenna to track the satellite at all times, whether you re parked or cruising down the highway, and its DewShield dew elimination system ensures optimum reception. Interface Box Options Purchased Separately The interface box allows you to set up and control the system using its four pushbuttons and LCD display. It also supplies power to the antenna and delivers satellite TV signals to your vehicle s satellite TV receiver

8 TracVision R6 User s Guide 1.2 How to Use this Manual This manual provides all of the information you need to operate, set up, and troubleshoot the TracVision R6 system. Who Should Use This Manual The user should refer to the Operation and System Preferences sections to learn how to operate the system using the interface box. The user or installer should refer to the Initial Setup section for information on configuring the system for the desired satellite TV service. The user or installer should refer to the System Wiring Diagrams appendix for information on connecting additional receivers or an HDTV converter. The user and/or servicing technician should refer to the Troubleshooting section to help identify the cause of a system problem. Icons Used in this Manual This manual uses the following icons to call attention to important information: Icon Description A helpful tip that either directs you to a related area within the manual or offers suggestions on getting the most from your system An alert to important information regarding procedures, product specifications, or product use Icon Description An illustration of the buttons on the interface box; gray shading indicates which button the user should press

9 Introduction Typographical Conventions This manual uses the following typographical conventions: Text Example Press menu. EXIT to exit the SELECT SATELLITES The display shows DIRECTV. <Satellite name> See Section 3.1, Turning DewShield On/Off. Description Both the icon and the name of the button are provided Text as it appears on the interface box display Text in quotes is shown on the interface box display Text inside brackets is variable Cross-reference to another section in the manual or to a web site Related Documentation In addition to this User s Guide, the following documents are provided with the TracVision R6 system: Document Installation Guide Quick Start Guide Product Registration Form Warranty Statement Contents List Description Complete product installation instructions Handy quick reference to basic operation and setup Details on registering the product Warranty terms and conditions List of every part supplied in the kit

10 Operation 2 Operation Contents This section explains how to operate your TracVision R6 system. It explains how to turn the system on/off and how to switch between satellites. 2.1 Receiving Satellite TV Signals Turning On the System Turning Off the System Understanding the Status Screen Switching Satellites

11 Operation 2.1 Receiving Satellite TV Signals TV satellites are located in fixed positions above the Earth s equator and beam TV signals down to certain regions of the planet (not worldwide). To receive TV signals from a satellite, you must be located within that satellite s unique coverage area. Figure 2-1 Location of the DIRECTV 101 Satellite Equator For your convenience, KVH provides links to several web sites that offer satellite coverage information. Simply visit our web site at In addition, since TV satellites are located above the equator, the TracVision antenna must have a clear view of the southern sky to receive satellite TV signals. Anything that stands between the antenna and the satellite can block the signal, resulting in lost reception. Common causes of blockage include trees, buildings, and bridges. Heavy rain, ice, or snow may also temporarily interrupt satellite signals. Figure 2-2 Satellite Blockage Blocked!

12 TracVision R6 User s Guide 2.2 Turning On the System Follow the steps below to turn on your TracVision R6 system. 1. Park your vehicle in an area with a clear view of the southern sky, away from trees or tall buildings. 2. Turn on your satellite TV receiver and TV. 3. Press the Power switch on the front of the TracVision interface box. 4. Wait 1 minute for system startup. Once the antenna finds the correct satellite, all three status lights on the interface box should be lit solid green. If any lights are not lit green, refer to Section 5.2, System Status Lights on page 42. Figure 2-3 Interface Box Components Display Buttons Power Switch Status Lights 2.3 Turning Off the System Follow the steps below to turn off your TracVision R6 system. 1. Press the Power switch on the front of the TracVision interface box. 2. Turn off your satellite TV receiver and TV

13 Operation 2.4 Understanding the Status Screen Following startup, the interface box display shows the current system status. Figure 2-4 Interface Box Status Screen TRACKING DTV 101 Antenna State Service Satellite Signal Strength If your system is set up for an HDTV converter, the status screen differs somewhat. See the table on the following page. Antenna State This field indicates the current state of the antenna: IDLE, INITIALIZING, SEARCHING, TRACKING, or ERROR. Service This code indicates the satellite TV service that is currently set up in the TracVision R6 system. During initial setup, you can choose from among four services: DTV (DIRECTV), DISH (DISH Network), EXVU (ExpressVu), and MAN (Manual). Satellite This number is the name of the satellite that the antenna is currently tracking. (The satellite name refers to the satellite s orbital slot, which is its longitudinal location above the equator.) Signal Strength These bars indicate the strength of the satellite TV signal, as measured by RF level. The more bars, the stronger the signal, just like a cell phone. In general, you need at least 3 bars for good reception

14 TracVision R6 User s Guide 2.5 Switching Satellites If your system is set up for multiple satellites, you can easily switch between them. Use the switching method that applies to your particular setup (see Section 3, Initial Setup on page 21 for details). You can identify the current satellite switching method by the format of the status screen. Status Screen Example TRACKING DTV 101 Satellite Switching Method Automatic TRACKING DISH 119 PUSH TO SWITCH SAT TRACKING<101>/119 PUSH FOR 101/110 Manual Automatic with HDTV Converter Automatic Satellite Switching If your system is set up for automatic switching, the antenna automatically switches satellites as you change channels using the receiver s remote control. The following antenna setups use automatic satellite switching: Service Antenna Setting Satellites DIRECTV OVAL2 101 and 119 DISH Network DISH and 110 ExpressVu DUAL LNB 91 and 82 Manual Satellite Switching If your system is not set up for automatic satellite switching, you need to use the interface box to switch between satellites. Press CHANGE until the display shows the desired satellite

15 Operation Automatic Satellite Switching with HDTV Converter If you have the optional KVH HDTV converter installed, and your system is set up for DIRECTV automatic switching with an HDTV converter, you can select between two satellite pairs for automatic switching: 101 and and 110 To order a KVH HDTV Converter (KVH part number ), contact your KVH dealer or call KVH directly at The selected pair appears at the top of the display and brackets (<>) surround the satellite that is currently selected for tracking. The antenna automatically switches between the two satellites in the selected pair as you change channels using the receiver s remote control. In the example below, the 101/119 pair is selected and the antenna is tracking the 101 satellite. Selecting the Alternate Satellite Pair Press CHANGE to select the alternate satellite pair. Figure 2-5 Status Screen in Automatic - HDTV Converter Mode Second Satellite Selected Satellite TRACKING<101>/119 PUSH FOR 101/110 Alternate Satellite Pair The following antenna setups use automatic satellite switching with the HDTV converter: For your convenience, KVH lists HDTV channels, and the DIRECTV satellites that carry them, on the web at Since DIRECTV changes its channel lineups frequently, KVH can updates to you whenever the HDTV lineup changes. Register for this free service when you visit the web site for the first time. Service Antenna Setting Satellites DIRECTV OVAL3 101, 110, and

16 System Preferences 3 System Preferences This section explains how to change the settings for DewShield and display brightness to suit your personal preferences. It also explains how to revert these settings to their factory defaults. Contents 3.1 Turning DewShield On/Off Adjusting the Display Brightness Setting to Defaults

17 System Preferences 3.1 Turning DewShield On/Off Your TracVision R6 antenna includes the DewShield electronic dew elimination system (patent pending). This revolutionary feature keeps the antenna dome clear of dew, ensuring optimum reception of satellite TV signals (moisture weakens signals). Unless power conservation is a critical concern, you should keep DewShield set to AUTO to prevent dew from forming. Follow the steps below if you need to change the current setting. 1. Press MENUS until the display shows DEW SHIELD. The DewShield dew elimination system is designed to prevent dew from forming on the antenna. If DewShield is set to off, and dew has formed on the dome, setting DewShield back to AUTO will not shed water. For this reason, KVH recommends that you always keep DewShield set to AUTO. DEW SHIELD= AUTO NEXT MENU CHANGE 2. Press CHANGE until the display shows the desired setting: AUTO or OFF. DEW SHIELD= OFF? CHANGE ACCEPT 3. Press ACCEPT. DEW SHIELD= OFF 4. Press EXIT to exit the menu

18 TracVision R6 User s Guide 3.2 Adjusting the Display Brightness Follow the steps below to adjust the brightness of the interface box display. 1. Press MENUS until the display shows BRIGHTNESS. BRIGHTNESS= HIGH NEXT MENU CHANGE 2. Press CHANGE until the display shows the desired setting: HIGH, MEDIUM, or LOW. BRIGHTNESS= MEDIUM? CHANGE ACCEPT 3. Press ACCEPT. BRIGHTNESS= MEDIUM 4. Press EXIT to exit the menu

19 System Preferences 3.3 Setting to Defaults The basic menu functions described in this section are set to the following defaults at the factory: DewShield: AUTO Brightness: HIGH Follow the steps below if you wish to restore these defaults. 1. Press MENUS until the display shows SET TO DEFAULTS. SET TO DEFAULTS= NO NEXT MENU CHANGE 2. Press CHANGE until the display shows SET TO DEFAULTS=YES. SET TO DEFAULTS=YES? CHANGE ACCEPT 3. Press ACCEPT. RESETTING TO DEFAULTS 4. Press EXIT to exit the menu

20 Initial Setup 4 Initial Setup When you turn on the TracVision R6 system for the first time, the interface box display shows SYSTEM NEEDS SETUP. This section explains how to set up the TracVision R6 system for your particular satellite TV service and receiver configuration. Contents 4.1 Initial Setup DIRECTV Initial Setup DISH Network Initial Setup ExpressVu Initial Setup Manual Mode Resetting the System to Change the Initial Setup

21 Initial Setup 4.1 Initial Setup DIRECTV Follow the steps below to set up the TracVision R6 for DIRECTV service. TRACKING DTV 101 SYSTEM NEEDS SETUP 1. Press any button to begin the setup process. If the status screen does not show System Needs Setup, follow the steps in Section 4.5, Resetting the System to Change the Initial Setup on page 36. SERVICE= DIRECTV? CHANGE ACCEPT 2. The display shows DIRECTV. Press ACCEPT. ANTENNA= ROUND? CHANGE ACCEPT 3. Press CHANGE until the display shows the desired antenna type (see the table below). The Antenna type you select should match the dish type setting on your satellite TV receiver. Refer to your receiver s owner s manual for details. Antenna Satellites Used Satellite Switching ROUND 101 only None (Unnecessary) OVAL2 101, 119 Automatic OVAL3* 101, 110, 119 Automatic with HDTV Converter MANUAL Select up to 4 Manual * Select OVAL3 only if you have a KVH HDTV converter installed

22 TracVision R6 User s Guide 4. Press ACCEPT. The remaining steps vary depending on the antenna type you selected. Follow the steps for your selected antenna type. Antenna Type = ROUND? The setup process is complete. The display shows the installed satellite (101) momentarily then the antenna restarts. INSTALLING SAT 101 RESTARTING ANTENNA Antenna Type = OVAL2? The setup process is complete. The display shows the installed satellites (101 and 119) momentarily then the antenna restarts. INSTALLING SATS RESTARTING ANTENNA

23 Initial Setup Antenna Type = OVAL3? Now you need to select which satellite pair you want the antenna to track first, 101/110 or 101/119. TRACK= 101/110? CHANGE ACCEPT 1. Press CHANGE until the display shows the desired satellite pair. 2. Press ACCEPT. The display shows the installed satellites (101, 119, and 110) momentarily then the antenna restarts. TRACK= 101/119 INSTALLING SATS RESTARTING ANTENNA

24 TracVision R6 User s Guide Antenna Type = MANUAL? Now you need to select which satellites to install in the antenna. The 101 satellite is required for DIRECTV service, so it is installed automatically as the first satellite. SAT 1 OF 4= 101 (REQUIRED) SAT 2 OF 4= NONE? CHANGE ACCEPT 1. Press CHANGE until the display shows the next satellite you want to install. You can choose 72, 110, 119, or NONE. 2. Press ACCEPT to install the satellite. 3. Repeat steps 1 and 2 for the remaining satellites you want to install. If you don t want to install four satellites, select NONE. Once you have installed all four satellites, or you have selected NONE, the display shows the installed satellites momentarily then the antenna restarts. INSTALLING SATS RESTARTING ANTENNA

25 Initial Setup 4.2 Initial Setup DISH Network Follow the steps below to set up the TracVision R6 for DISH Network service. TRACKING DTV 101 SYSTEM NEEDS SETUP 1. Press any button to begin the setup process. If the status screen does not show System Needs Setup, follow the steps in Section 4.5, Resetting the System to Change the Initial Setup on page 36. SERVICE= DIRECTV? CHANGE ACCEPT 2. Press CHANGE until the display shows DISH. SERVICE= DISH? CHANGE ACCEPT 3. Press ACCEPT. ANTENNA= DISH500? CHANGE ACCEPT

26 TracVision R6 User s Guide 4. Press CHANGE until the display shows the desired antenna type (see the table below). Antenna Satellites Used Satellite Switching DISH , 110 Automatic MANUAL Select up to 4 Manual 5. Press ACCEPT. The remaining steps vary depending on the antenna type you selected. Follow the steps for your selected antenna type. Antenna Type = DISH500? The display momentarily shows the installed satellites (119 and 110) then the antenna restarts. INSTALLING SATS RESTARTING ANTENNA Now you need to run the Check Switch function on your DISH Network receiver to configure the receiver for TracVision compatibility. Follow the steps in Running the Receiver Check Switch Function on page

27 Initial Setup Antenna Type = MANUAL? Now you need to select which satellites to install in the antenna. The 119 satellite is required for DISH Network service, so it is installed automatically as the first satellite. SAT 1 OF 4= 119 (REQUIRED) SAT 2 OF 4= NONE? CHANGE ACCEPT 1. Press CHANGE until the display shows the next satellite you want to install. You can choose 61, 110, 129, 148, or NONE. 2. Press ACCEPT to install the satellite. 3. Repeat steps 1 and 2 for the remaining satellites you want to install. If you don t want to install four satellites, select NONE. Once you have installed all four satellites, or you have selected NONE, the display shows the installed satellites momentarily then the antenna restarts. INSTALLING SATS RESTARTING ANTENNA Now you need to run the Check Switch function on your DISH Network receiver to configure the receiver for TracVision compatibility. Follow the steps in Running the Receiver Check Switch Function on page

28 TracVision R6 User s Guide Running the Receiver Check Switch Function To configure your DISH Network receiver to work with the TracVision antenna, follow the steps below to run the receiver s Check Switch function. 1. Turn on the receiver and the TV. 2. Using the receiver s remote control, go to the Point Dish/Signal Strength screen (press Menu, 6, 1, 1 (on most models)). 3. At the Point Dish/Signal Strength screen, select the 119 satellite. 4. Select the Test button. The receiver begins configuring itself for TracVision operation. 5. Wait until the Check Switch function is complete. It will take a couple minutes. 6. If you set up the antenna for DISH500 antenna type, verify that the TV shows the following: Installed Switch: SW42 Input: Satellite: Polarity: Odd Even Odd Even Status: Satellite reception verified If you set up the antenna for Manual antenna type, verify that the TV shows No Switch Detected, Switch Type Unknown, or a similar error message. 7. If the information is not displayed as noted in Step 6, try running the Check Switch function again. 8. When you are done, exit the menu and allow the receiver to download the program guide

29 Initial Setup 4.3 Initial Setup ExpressVu Follow the steps below to set up the TracVision R6 for ExpressVu service. TRACKING DTV 101 SYSTEM NEEDS SETUP 1. Press any button to begin the setup process. If the status screen does not show System Needs Setup, follow the steps in Section 4.5, Resetting the System to Change the Initial Setup on page 36. SERVICE= DIRECTV? CHANGE ACCEPT 2. Press CHANGE until the display shows EXPRESSVU. SERVICE= EXPRESSVU? CHANGE ACCEPT 3. Press ACCEPT. ANTENNA= SINGLE LNB? CHANGE ACCEPT

30 TracVision R6 User s Guide 4. Press CHANGE until the display shows the desired antenna type (see the table below). Antenna Satellites Used Satellite Switching SINGLE LNB 91 None (Unnecessary) DUAL LNB 91, 82 Automatic MANUAL Select up to 2 Manual 5. Press ACCEPT. The remaining steps vary depending on the antenna type you selected. Follow the steps for your selected antenna type. Antenna Type = SINGLE LNB? The setup process is complete. The display shows the installed satellite (91) momentarily then the antenna restarts. INSTALLING SAT 91 RESTARTING ANTENNA Antenna Type = DUAL LNB? The setup process is complete. The display shows the installed satellites (91 and 82) momentarily then the antenna restarts. INSTALLING SATS RESTARTING ANTENNA

31 Initial Setup Antenna Type = MANUAL? Now you need to select which satellites to install in the antenna. The 91 satellite is required for ExpressVu service, so it is installed automatically as the first satellite. SAT 1 OF 2= 91 (REQUIRED) SAT 2 OF 2= NONE? CHANGE ACCEPT 1. Press CHANGE until the display shows the next satellite you want to install. You can choose either satellite 82 or NONE. 2. Press ACCEPT to install the satellite. The display shows the installed satellites momentarily then the antenna restarts. INSTALLING SATS RESTARTING ANTENNA

32 TracVision R6 User s Guide 4.4 Initial Setup Manual Mode If the status screen does not show System Needs Setup, follow the steps in Section 4.5, Resetting the System to Change the Initial Setup on page 36. Follow the steps below to manually set up the TracVision R6 to track your own unique set of satellites. TRACKING DTV 101 SYSTEM NEEDS SETUP 1. Press any button to begin the setup process. SERVICE= DIRECTV? CHANGE ACCEPT 2. Press CHANGE until the display shows MANUAL. SERVICE= MANUAL? CHANGE ACCEPT 3. Press ACCEPT. SAT 1 OF 5= 101? CHANGE ACCEPT

33 Initial Setup 4. Press CHANGE until the display shows the first satellite that you want to install. You can choose any five of the following satellites: Press ACCEPT to install the satellite. 6. Repeat steps 4 and 5 for the remaining satellites you want to install. If you don t need to install five satellites, select NONE. Once you have installed all five satellites, or you have selected NONE, the display shows the installed satellites momentarily then the antenna restarts. INSTALLING SATS RESTARTING ANTENNA

34 TracVision R6 User s Guide 4.5 Resetting the System to Change the Initial Setup If you need to change the antenna s setup to receive a different satellite TV service and/or track a different satellite, follow the steps below to reset the system. Once the system has reset to its factory condition, you will be able to complete an initial setup as described in the previous sections. 1. Press MENUS until the display shows DIAGNOSTICS. DIAGNOSTICS= NO NEXT MENU CHANGE 2. Press CHANGE until the display shows DIAGNOSTICS= YES. DIAGNOSTICS= YES? CHANGE ACCEPT 3. Press ACCEPT to enter the Diagnostics menu. ENTERING DIAGNOSTICS SYSTEM RESET= NO NEXT MENU CHANGE

35 Initial Setup 4. Press CHANGE until the display shows SYSTEM RESET= YES. SYSTEM RESET= YES? CHANGE ACCEPT 5. Press ACCEPT to reset the system. SYSTEM RESET 6. When the display shows the status screen, set up the system for the desired service. Follow the steps in Section 4.1, 4.2, 4.3, or 4.4. TRACKING DTV 101 SYSTEM NEEDS SETUP

36 Troubleshooting 5 Troubleshooting This section identifies basic problems along with their possible causes and solutions. It also explains what the status lights indicate, how to perform a diagnostics test, and how to get technical support. Contents 5.1 Five Simple Checks System Status Lights Running the Diagnostics Test Viewing System Information Technical Support Product Care

37 Troubleshooting 5.1 Five Simple Checks If you are experiencing a problem receiving satellite TV with your TracVision system, first check the five simple things below. If none of these are the problem, check the status lights on the TracVision interface box and/or perform a diagnostics test, as explained in the remainder of this section. 21 Can the Antenna See the Satellite? The antenna requires an unobstructed view of the southern sky to receive satellite TV signals. Common causes of blockage include trees, buildings, overpasses, and mountains. The TracVision antenna will not work inside a garage. 2 Is There Excessive Dirt or Moisture on the Antenna Dome? Dirt buildup or moisture on the dome can reduce satellite reception. Clean the exterior of the dome periodically and keep DewShield set to AUTO to ensure optimum reception (refer to Section 3.1, Turning DewShield On/Off on page 17). 3 Is It Raining Cats and Dogs? Heavy rain or snow can weaken satellite TV signals. Reception should improve once the inclement weather subsides. 24 If You Have DIRECTV, Does the TV Display a Please Call Ext. 722 Message? If you can only access the DIRECTV preview channels, such as channel 100, while all other channels show a message to call Ext. 722, the receiver may have lost its activation data. To fix this problem, call DIRECTV customer service at DIRECTV ( ). Be sure the antenna is tracking the satellite when you call. You can also try resetting the satellite TV receiver before you begin troubleshooting: 1. Park in a blockage-free area. 2. Turn off and unplug the receiver. 3. Wait 1 minute, then plug the receiver back in. 4. Turn on the receiver and the TracVision antenna. Satellite Mismatch? If the interface box and the antenna get out of sync, the display shows System Sat Mismatch. SYSTEM SAT MISMATCH PRESS TO FIX Just press ACCEPT to fix the problem. The interface box will synchronize with the antenna and ensure that the satellite setup in the antenna matches the setup in the interface box. 45 Are the Interface Box, Satellite TV Receiver, and TV Turned On and Connected Properly? Make sure the power switch on the front of the TracVision interface box is turned on (the VOLTAGE light is lit green). Also make sure your TV and receiver are both turned on and set up for the satellite input. Finally, check the cables connecting all these components to ensure none have come loose

38 TracVision R6 User s Guide 5.2 System Status Lights Three status lights on the front of the receiver indicate the current status of the system and can help you identify problems. Figure 5-1 System Status Lights During normal operation, all three status lights should be lit green. The tables on the following page explain what the different light conditions indicate

39 Troubleshooting VOLTAGE Light Indications Light is... Indicates Description Off Off Interface box is OFF (power switch is off) or no power input Green OK Good power (between VDC at interface box) Green, flashing Cable Open Open detected in antenna cable (check antenna coax connection) Orange Low Power Low power (between 8-10 VDC at interface box) Red, flashing Bad Power Insufficient power (less than 8 VDC or more than 16 VDC input) RECEIVER Light Indications Light is... Indicates Description Green OK Good communications with receiver Orange No Comm No communications with receiver Orange, flashing* Overload Overload or short circuit detected on the antenna cable Red Fault Internal power fault ANTENNA Light Indications Light is... Indicates Description Off Off Antenna is OFF, disconnected, or has insufficient power Green Tracking Antenna is tracking the selected satellite Green, flashing Searching Antenna is searching for a satellite Orange, flashing* Overload Overload or short circuit detected on the antenna cable Red No Comm No communications with antenna Red, flashing Fault Error detected in antenna * The RECEIVER and ANTENNA lights both flash orange if an overload or short circuit is detected

40 TracVision R6 User s Guide 5.3 Running the Diagnostics Test In addition to the front panel status lights, the interface box includes a self-test function within its Diagnostics menu. Follow the steps below to run this test. 1. Press MENUS until the display shows DIAGNOSTICS. DIAGNOSTICS= NO NEXT MENU CHANGE 2. Press CHANGE until the display shows DIAGNOSTICS= YES. DIAGNOSTICS= YES? CHANGE ACCEPT 3. Press ACCEPT to enter the Diagnostics menu. ENTERING DIAGNOSTICS SYSTEM RESET= NO NEXT MENU CHANGE

41 Troubleshooting 4. Press MENUS until the display shows RUN TEST. RUN TEST= NO NEXT MENU CHANGE 5. Press CHANGE until the display shows RUN TEST= YES. RUN TEST= YES? CHANGE ACCEPT 6. Press ACCEPT to begin the test. RUNNING TEST ANTENNA: TRACKING PRESS TO CONTINUE 7. Once the test is complete, the display shows the antenna status. Press MENUS to scroll through the remaining status messages

42 TracVision R6 User s Guide The table below lists all of the status messages and their possible states. Diagnostics Test Indications Component Tested ANTENNA CURRENT SAT RF LEVEL AVAILABLE SATS GPS CABLE STATE SYSTEM DC ANTENNA DC Possible States IDLE INITIALIZING SEARCHING TRACKING ERROR <Name of satellite the antenna is tracking> ERROR OK, <actual RF level> LOW, <actual RF level> ERROR, COMM <Satellite name> Press MENUS to scroll through the list of available satellites ERROR <current position in latitude/longitude> ACQUIRING ERROR OK SHORTED OPEN OK; <VDC power at the interface box> LOW; <VDC power at the interface box> BAD; <VDC power at the interface box> OK; <VDC power at the antenna> LOW; <VDC power at the antenna> BAD; <VDC power at the antenna>

43 Troubleshooting 5.4 Viewing System Information You can view the TracVision system s software versions and serial numbers on the interface box display. Follow the steps below to display the system information. 1. Press MENUS until the display shows DIAGNOSTICS. DIAGNOSTICS= NO NEXT MENU CHANGE 2. Press CHANGE until the display shows DIAGNOSTICS= YES. DIAGNOSTICS= YES? CHANGE ACCEPT 3. Press ACCEPT to enter the Diagnostics menu. ENTERING DIAGNOSTICS SYSTEM RESET= NO NEXT MENU CHANGE

44 TracVision R6 User s Guide 4. Press MENUS until the display shows SHOW SYS INFO= NO. SHOW SYS INFO= NO NEXT MENU CHANGE 5. Press CHANGE until the display shows SHOW SYS INFO= YES. SHOW SYS INFO= YES? CHANGE ACCEPT 6. Press ACCEPT to begin viewing the system information. KVH INDUSTRIES PRESS TO CONTINUE 7. Press MENUS to scroll through the list. TRACVISION R6 PRESS TO CONTINUE

45 Troubleshooting The table below lists all of the information reported by the interface box. System Information Item TRACVISION <model> SYS SW: <#> RF SW: <#> MOTOR SW: <#> JBOX SW: <#> ANT. SER. # <#> JBOX SER. # <#> Description Model of TracVision antenna (e.g., R6 ) Version of antenna main software Version of antenna RF software Version of antenna motor software Version of interface box software Serial number of antenna Serial number of interface box 5.5 Technical Support If you experience an operating problem or require technical assistance, please contact your local authorized TracVision dealer/installer first. You can find an authorized technician near you by visiting our website at If an authorized technician is not located nearby, please contact KVH Technical Support directly: Phone: techs@kvh.com Internet: Please have your antenna and interface box serial numbers handy before you call

46 TracVision R6 User s Guide 5.6 Product Care Please consider the following antenna care guidelines to maintain peak performance. Periodically wash the exterior of the antenna dome with fresh water and mild detergent. Avoid harsh cleansers and volatile solvents (e.g., acetone) and do not spray the dome directly with high-pressure water. If you wish to paint the dome, use only nonmetallic automotive paint without a primer coat. Metallic paint or paint having a metallic color will block satellite signals. Consider the antenna s height before driving under low-clearance structures

47 Appendices Appendices Contents This section provides wiring diagrams and notes for various TracVision system configurations. A System Wiring Diagrams Index

48 System Wiring Diagrams Appendix A System Wiring Diagrams The diagrams on the following pages show how to wire the system for various configurations: Configuration Requires KVH P/N(s)*: See page: One (1) receiver N/A 54 Two (2) receivers Three (3) or more receivers & One (1) receiver with HDTV converter (DIRECTV only) Automatic Satellite Switching Two (2) receivers with HDTV converter (DIRECTV only) Manual Satellite Switching Three (3) or more receivers with HDTV converter (DIRECTV) Manual Satellite Switching , , & Three (3) or more receivers with HDTV converter (DIRECTV) Automatic Satellite Switching x 2, , , & * RF coax cables sold separately Destacker, Single-output ( ) or Dual-output ( ) The destacker converts a stacked signal into an unstacked signal, which standard satellite TV receivers are configured to decode. Active Multiswitch ( ) The active (powered) multiswitch allows you to connect multiple receivers. KVH recommends Channel Master model 6214IFD or equivalent. This multiswitch amplifies the signal to compensate for signal loss. A passive multiswitch will not provide the necessary amplification. Digital Video Recorders (DVRs): DVRs, such as TiVo, require two satellite inputs, whereas a standard receiver requires only one input. Therefore, to connect a DVR to the TracVision system, you need to wire the DVR just like you would wire two receivers. HDTV Converter Kit ( ) The HDTV converter adjusts the signal frequency of the DIRECTV 110 satellite, allowing you to receive its HD channels. The kit includes a single-output destacker. Splitter ( ) The splitter divides the control signal from the interface box, which allows it to activate two HDTV converters

49 TracVision R6 User s Guide Wiring Diagram for a Single Receiver To Antenna Input Power (10-16 VDC) Ground Interface Box Satellite TV Receiver TV ANT/CABLE IN R L OUT TO TV AUDIO VIDEO S-VIDEO PHONE JACK

50 System Wiring Diagrams Wiring Diagram for Two Receivers Interface Box To Antenna Input Power (10-16 VDC) Ground Satellite TV Receiver (Master) TV ANT/CABLE IN R L OUT TO TV AUDIO VIDEO S-VIDEO PHONE JACK NOT USED INPUT TERRESTRIAL / TV Destacker OUTPUT / SAT RECEIVER Satellite TV Receiver TV ANT/CABLE IN R L OUT TO TV AUDIO VIDEO S-VIDEO PHONE JACK Components Required KVH P/N: Destacker, single-output

51 TV ANT/CABLE IN OUT TO TV TV ANT/CABLE IN OUT TO TV TV ANT/CABLE IN OUT TO TV TV ANT/CABLE IN OUT TO TV TV ANT/CABLE IN OUT TO TV R R R R R L AUDIO VIDEO S-VIDEO PHONE JACK L AUDIO VIDEO S-VIDEO PHONE JACK L AUDIO VIDEO S-VIDEO PHONE JACK L L AUDIO VIDEO S-VIDEO PHONE JACK AUDIO VIDEO S-VIDEO PHONE JACK TracVision R6 User s Guide Wiring Diagram for Multiple Receivers Using a Multiswitch Interface Box To Antenna Input Power (10-16 VDC) Ground Satellite TV Receiver (Master) Destacker INPUT TERRESTRIAL / TV TO RECEIVER / DBS OUTPUT A B Components Required KVH P/N: Input Power (12 VDC) POWER LNB LHCP/+18V VHF/UHF INPUT LNB RHCP/+13V Destacker, dual-output Multiswitch Multiswitch OUT 1 OUT 2 OUT 3 OUT 4 Satellite TV Receivers

52 System Wiring Diagrams Wiring Diagram for a Single Receiver and an HDTV Converter (DIRECTV only) To Antenna Interface Box Input Power (10-16 VDC) Ground RF INPUT CONTROL INPUT HDTV Converter RF OUT HD Receiver TV ANT/CABLE IN R L OUT TO TV AUDIO VIDEO S-VIDEO PHONE JACK Components Required KVH P/N: HDTV Converter Kit

53 TV ANT/CABLE IN OUT TO TV TV ANT/CABLE IN OUT TO TV R R L L AUDIO VIDEO S-VIDEO PHONE JACK AUDIO VIDEO S-VIDEO PHONE JACK TracVision R6 User s Guide Wiring Diagram for Two Receivers and an HDTV Converter (DIRECTV only) In this configuration, the antenna must be set up for manual satellite switching between the 101, 110, and 119 satellites. Refer to Section 4.1, Initial Setup - DIRECTV on page 23 for setup instructions. Interface Box To Antenna Input Power (10-16 VDC) Ground Standard Definition Receiver (Master) Destacker INPUT TERRESTRIAL / TV OUTPUT / SAT RECEIVER HDTV Converter RF INPUT CONTROL INPUT RF OUT HD Receiver Components Required HDTV Converter Kit (includes single-output destacker) KVH P/N:

54 TV ANT/CABLE IN OUT TO TV TV ANT/CABLE IN OUT TO TV R R L L AUDIO VIDEO S-VIDEO PHONE JACK AUDIO VIDEO S-VIDEO PHONE JACK System Wiring Diagrams Wiring Diagram for Multiple Receivers and an HDTV Converter (DIRECTV only) Interface Box To Antenna Input Power (10-16 VDC) Ground Standard Definition Receiver (optional) Destacker INPUT TERRESTRIAL / TV TO RECEIVER / DBS OUTPUT A B HDTV Converter RF INPUT CONTROL INPUT In this configuration, the antenna must be set up for manual satellite switching between the 101, 110, and 119 satellites. Refer to Section 4.1, Initial Setup - DIRECTV on page 23 for setup instructions. RF OUT Components Required KVH P/N: Input Power (12 VDC) POWER LNB LHCP/+18V VHF/UHF INPUT LNB RHCP/+13V HDTV Converter Kit Destacker, dual-output Multiswitch Multiswitch OUT 1 OUT 2 OUT 3 OUT 4 HD Receiver To 3 Other Receivers

55 TV ANT/CABLE IN OUT TO TV TV ANT/CABLE IN OUT TO TV R R L AUDIO VIDEO S-VIDEO PHONE JACK L AUDIO VIDEO S-VIDEO PHONE JACK TracVision R6 User s Guide Wiring Diagram for Multiple Receivers and an HDTV Converter (DIRECTV only) Interface Box To Antenna Input Power (10-16 VDC) Ground Splitter OUT INPUT OUT In this configuration, the antenna may be set up for automatic satellite switching between the 101, 110, and 119 satellites. Refer to Section 4.1, Initial Setup - DIRECTV on page 23 for setup instructions. Destacker INPUT TERRESTRIAL / TV RF INPUT CONTROL INPUT TO RECEIVER / DBS OUTPUT A B HDTV Converter RF OUT HD Receiver RF INPUT CONTROL INPUT HDTV Converter RF OUT Components Required KVH P/N: Input Power (12 VDC) POWER LNB LHCP/+18V VHF/UHF INPUT LNB RHCP/+13V HDTV Converter Kit x 2 Destacker, dual-output Multiswitch Multiswitch Splitter OUT 1 OUT 2 OUT 3 OUT 4 HD Receiver To 3 Other Receivers

56 Index Index A add receivers, 53 antenna cable state, 46 description, 3 faults, 43, 46 height, 3 model, 49 ANTENNA light, antenna type DIRECTV, 23 DISH Network, 28 ExpressVu, 32 B blockage, 9, 41 brightness, adjust, 18 buttons, 10 C cable state, 46 change satellites, see switch satellites Check Switch, DISH Network, 30 cleaning, 50 configure, DISH Network receiver, 30 connection diagrams, conserve power, 17 coverage area, satellite, 9 D default settings, 19 destacker, 53 DewShield, 17 diagnostics, digital video recorder (DVR), 53 DIRECTV antenna type, 23 ext 722 message, 41 setup, DISH Network antenna type, 28 Check Switch, 30 setup, dish type, see antenna type display, 10 display brightness, 18 E ExpressVu setup, F factory settings, 19 G GPS status, 46 gyros, 3 H help, technical, 49 HD channel list, 13 HDTV converter antenna type requirement, 23 description, 53 part number, 53 switch satellites, 13 wiring, height, antenna, 3 I install satellites, interface box, description, 3 L LCD, 10 lights (LEDs), status, 10,

57 TracVision R6 User s Guide M maintenance, 50 manual setup, model, antenna, 49 moisture on dome, 17, 41 multiple receivers, 53 multiswitch, 53 O obstructions, signal, 9, 41 overload, 43 overview, product, 3 P painting, 50 part numbers, accessories, 53 power conservation, 17 power fault, 43, 46 power on/off, 10 power switch, 10 preferences, set, R rain fade, 41 RECEIVER light, receiver reset, 41 repair, 49 reset system, restore defaults, 19 RF level, 46 S satellites coverage area, 9 install, list of available, 35 pairs, HDTV, 13, 25 switch, serial numbers, 49 service, 49 setup change, DIRECTV, DISH Network, ExpressVu, manual, short circuit, 43, 46 signal strength, 11 software versions, 49 splitter, 53 stacked signal, 53 status indicators, 10, switch satellites automatic, HDTV converter, 13 manual, 12 system information, system needs setup, 21 system sat mismatch, 41 T technical support, 49 test, diagnostics, TiVo, 53 troubleshooting, turn on/off, 10 U unstacked signal, 53 V versions, software, 49 VOLTAGE light, W wiring diagrams,

58 TVR6_Jbox_UG_Cover_1.06 KVH Industries, Inc. 50 Enterprise Center Middletown, RI U.S.A. Phone: (401) Fax: (401) Copyright 2006, KVH Industries, Inc. KVH and TracVision are registered trademarks of KVH Industries, Inc.