G-700 Quick User Guide

Size: px
Start display at page:

Download "G-700 Quick User Guide"

Transcription

1 Quick User Guide (Multiple channel Curved Screen Edge Blender) Technical support: Tel: ext. 301 Cell: Skype: vns-inc Version: 3.02 Website: 0

2 Table of Contents 1 Introduction Outlook and Function Helpful Tips for system installation and setup Edge Blending procedures Determine source signal resolution and number of projector System connection Excel Spread Sheet calculation Mark image location Set overlapped region size Projector settings and installation GeoBox setting Geometry alignment by OSD menu [Video Wall] settings [Edge Blend] settings Overlap region gamma correction Black level uplift Image quality fine-tuning System power ON/OFF setting Enable Black Screen while no input signal or mode change Save all settings into Profile Thermal drift in projector image position PC output resolution setting Geometry alignment by Gwarp2 PC Tool Keyboard hotkeys for convenient Gwarp2 operation System reset [Warp] adjustment Uniformity adjustment [All]: OSD simultaneous control in all channels [EDID] setting System bandwidth and system crash Screen Selection Projector Selection and settings Specifications Limited Warranty This device is designed and tested to the highest standards and backed by two years parts and labor warranty. Warranties are effective upon the first delivery date to the end customer and are non-transferable. Warranty related repairs include parts and labor, but do not include repair of faults resulting from user negligence, special modifications, abuse (mechanical damage), shipping damage, and/or other unusual damages. The customer shall pay shipping charges when the unit is returned for repair. Manufacturer will pay shipping charges for return shipments to customers. Manufacturer does not assume responsibility for consequential damages, expenses or loss of revenue, inconvenience or interruption in operation experienced by the customer. Warranty service shall not automatically extend the warranty period. FCC/CE statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential / commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. 1

3 1 Introduction is a curved screen edge blending processor with ability to provide multiple processing channels to control from 1 to 4 projectors based on user s requirements. G-106 can provide single processing channel for one projector, G-702 for 2 projectors, G-703 for 3 projectors and G-704 for 4 projectors. It was designed for sophisticated edge blending as well as image warping, stacking, projection mapping, irregular video wall and passive 3D etc. Each processing channel has 3 input ports (1x HDMI, 1x DP, 1x DVI-I) to support 5 input formats (HDMI, DP, VGA, DVI-D, YPbPr) and one HDMI output port. One 4K HDMI loop out port is for raw signal daisy chain connection. Input ports support up to and 4k resolution with 4:4:4 full color sampling. It is integrated with 10-bit high end processor, motion adaptive de-interlace, low angle smooth algorithm and 3:2/2:2 pull-down. PIP (picture in picture) and POP (side by side) are standard functions in each processing channel. In one G-704, user can display up to 8 different input contents on the screen. If user requires PIP or POP image across entire screen, user can use the first channel as PIP/POP processor and connect the output to other processing channel input port to get it. Advanced warp technology is embedded in. User can use front panel keypads, IR controller and PC tool to perform edge blending and sophisticated geometry alignment up to 17x17 grids. Independent color (white balance) adjustment for each projector, overlapped area color correction and non-overlapped area black level uplift are also standard functions in. Users can see real time geometry and color adjustment and get optimized result. HDMI loop out supports daisy chain connection up to or and allows large display with multiple cascaded without video distributor. Video wall function in is to crop and allocate source image for each projector. Complete curved edge blending can be achieved without PC, video distributor and splitter. is an ideal solution for simulation. It can connect with inputs from multiple PC and combine them into one seamless image. It also provides flexible displays in edge blending system. For a 3x projector edge blending system, user can configure as independent display, 1+2 (two edge blends) and all-in-one (three edge blends). User can also execute edge blending with projector at portrait position to increase image height. It is a good fit with laser projector without the limitation in installation angle. In order to optimize video performance, is designed to support non-vesa standard input timing and allow user to create any EDID timing in the range between 1024x768 and 3840x2400. With, users can replace high end projector with low cost projector without lens shift, warp and edge blending. It provides easy configuration, low entry barrier, cost effective, reliable and flexible solution. 2

4 2 Outlook and Function 3 Helpful Tips for system installation and setup a. Select digital input to get better image and avoid image position shift. b. If 4k signal connection distance is more than 10m, please select a certified HDMI cable to avoid unstable signal connection. Usually [High Speed HDMI + Ethernet] cable will be better. c. The quality for signal adapter or converter, such as HDMI to DVI adapter and DisplayPort to HDMI converter, may downgrade the signal quality and cause issue. Please select qualified ones. d. If user can see blue background image with [Power Saving Mode] message, it means the signal connection between projector and GeoBox is OK but no input signal detected by GeoBox. Please check signal source or replace a different input source to test. e. If user can t see [Power Saving Mode] message or splash screen, please check the connection between GeoBox and projector. User can connect to a monitor to check the output from GeoBox. [Loop out] port is for raw signal daisy chain connection and is not an output to projector. f. The output resolution setting shall be the same as projector native resolution to get the best video quality. After geometry alignment, this output resolution can t be changed. Otherwise, geometry position will be shifted and required further adjustment. g. In the application with short throw ratio projector on curved screen, it is possible that the image location is beyond the maximum adjustment range in manual adjustment. In this case, Gwarp PC tool is required to double the adjustment range. 3

5 h. During installation setup process, please apply FHD signal to the system for easy setup. After finish the setup, user can select optimized EDID from OSD menu to get optimized video quality. i. The optimized EDID resolution should be the final resolution after edge blending. For instance, if user uses three XGA projectors for edge blending with 250 overlapped pixels, then the best signal for this setup will be 1024*3-250*2=2572. It means 2572*768 will be the best signal resolution for this setup. User can customize EDID with this resolution in GeoBox. Some PC may not be able to output the same custom resolution. In this case, user needs to set PC output resolution as close this timing as possible. GeoBox can support none-vesa standard input timings. j. In addition to the resolution settings, user needs to provide content with the same aspect ratio as screen to ensure no distortion on the screen. k. To reset all projectors before edge blending to get the same settings in all projectors. l. To turn off auto keystone function to avoid image shift. m. In order to avoid interference among multiple GeoBox during the installation, user can set ID number for each GeoBox through [Options] Menu. Press number keys in Remote Controller for the control of multiple GeoBox: 850: simultaneous control for all GeoBox 851: control GeoBox ID No : control GeoBox ID No. 3 User will see flashing LED on front panel after press 85x number keys. It means the OSD menu in GeoBox with flash LED is locked and will not be controlled by remote controller. n. OSD Lock / Unlock: When continuously press [OKD Lock] key on Front Panel or [Menu] key in IR Remote Control for 5 seconds, the OSD function will be locked to prevent from setting change by negligence. To press [OSD Lock] key or [MENU] key for 5 seconds again, it will unlock OSD and user can manipulate the OSD again. o. [Image Setup] menu will not be activated if the input source is not from VGA. p. Please reset GeoBox before any new application to avoid unexpected settings in the system. User can insert a pin into Reset Hole on the back panel and hold for 5 seconds to reset the settings in all channels at the same time. q. To set [Menu Time Out] to 0, the OSD will appear till the OSD Menu has been turned off manually or system input timing change. r. Default Internal Grid Pattern represents 32x32 pixels no matter which input resolution is selected. s. Only HDMI-A input port can provide HDMI raw signal loop out for daisy chain connection. This loop out signal has no any processing. t. When [Gwarp] PC tool is used, user needs to save the setting into GeoBox through the OSD menu: [Anyplace] [Gwarp Pro] select [UserMap 1-10] to save the settings. Then PC can be removed. u. When Power Off/ON GeoBox, it will maintain the final settings. v. User needs to save the final setting into [Profile] under [Options] menu for long tern stored inside the system. Even the system is reset, the [Profile] settings will be kept without change. 4

6 w. Continuously press PATTERN button, internal test pattern will show different colors for easy installation: White Red Green Blue Blank. When in Blank, user can see OSD and the image from signal source. In this case, PC test pattern can be applied. x. Please use INFO hot key on front panel or remote controller to check the input and output timing. The indicators on the front panel will show the input/output connection status. y. User can set black background while no input signal is detected and input timing change under [Options] [Accessibility] menu. z. Below hotkeys are available in remote controller: [Warp] geometry alignment, [Video wall], [Edge Blend], [Info], [CH A/B] switching. 4 Edge blending procedures 4.1 Determine source signal resolution and number of projector a b c d e The image size and watching distance are two major factors to determine source signal resolution and number of the projectors. If the screen size is 20m and the watching distance is 5m, the signal pixel pitch should be around 5mm, then the system resolution is about 20m/5mm=4000. It means the system resolution should be around 4000 pixels in width and the vertical resolution should follow the projector native resolution. If 1080p projector is used, the system resolution should be 3840x1080 or 4096x1080 if signal source can support this output timing. After determine the system resolution, please make sure all the equipment in the signal pipe line should be able to support this resolution or higher. It includes signal source output, edge blending processor and the total resolution of the projectors after edge blending. If user uses 8x XGA projector with 250 overlap pixels, the total projector resolution after edge blending will be 1024*8-250*7=6442 pixels. It means it is enough to use XGA resolution projectors in this case. If user uses FHD or WUXGA high end projectors with watching distance at 5m, the final video quality will be very similar if signal source is only 4k resolution. VNS can provide service free of charges to help customers in making project plan, including system configuration, type of projector, signal source and installation data. 4.2 System connection a b c d e HDMI Loop Out port is for daisy chain connection. It is not an input port. Only the input signal from HDMI input port can be looped out. Input signal can be connected to any processing module and looped out to next processing module. No special sequence is required. User needs to use Micro USB cable for PC & connection if Gwarp PC Tool is used. User can use USB extension cable to extend the connection distance. IF GeoBox is installed in control room, please extend IR receiver to a place for easy remote controller access. User can use audio cable to extend up to 20 meters. 5

7 f g h i User can execute OSD operation through Ethernet Web browser. Virtual keys in WebGui are available. Ethernet module is option. Need to be installed in factory. Select input port and set GeoBox output resolution to be same as projector native resolution. User needs to apply a signal source while video wall [Overlap] value setting. Signal source resolution should be the same as Excel calculation. To apply 1080p signal is recommended. After system setup, user can use any input resolution. Press [INFO] hotkey to check if the setting is the same as expected. 4.3 Excel Spread sheet calculation a User needs to get below data for edge blending plan: (3x projectors as Example) Input signal resolution: (3840*800) Number of projector.(3 projectors) Projector resolution and lumens. (1280*800, 3200 Lum) Required image size (screen size: 6.5m*1.5m) Overlap pixels and dimension. (8 grids=8*32= 256 pixels) Projector throw ratio:

8 Based on these data, user can make a layout plan and decide the installation dimensions and locations. b The above is the calculation result. Please contact dealer or factory to get necessary assistance for these data. Final image size for each projector: 2.500m*1.563m User can use geometry alignment to draw the vertical height to the dimensions you need. In this example, the final image height is 1.5m after geometry alignment. Optimized content resolution: 3328*800 (This is the ideal resolution to set EDID) Installation distance: 3m-4.25m It is calculated from throw ratio and image wide for each projector. (2.5m*1.2=3m, 2.5m*1.7=4.25m) The overlap value in video wall setting: Projector LH: select RH edge: +197 Projector (Center): LH edge=+98, RH edge=+99 (total 197) Projector RH: LH edge: +197 After finish setting, user can check the image, if some overlap area is still blurred, Please increase or decrease Overlap Value with 1-2 steps and select optimized one. The final luminance is 819 Lux. It will be enough for inside room environment. c It is allowed to have different overlap pixel among all projectors. Irregular Spread Sheet is required to calculate the result. 4.4 Mark image location After Excel Spread Sheet calculation, user can understand the final image position for each projector. Please mark image position by paper adhesive tape on the screen. The positions should include 4 corners of the image for each projector and horizontal center line of the screen. Please select a tape that will not damage the screen. Laser leveler is an ideal tool for marking center line, horizontal and vertical image positions. 4.5 Set overlapped region size a During Excel Spread Sheet calculation, user has some flexibility to determine the overlap 7

9 region size by different projector resolution, lumens and number of projector. b Please reserve at least 214 overlapped pixels for XGA projector and 352 pixels for 1080P/WUXGA projector or 40cm-100cm overlapped region (it will also depend on screen size and Excel calculation). GeoBox maximum edge blend region is 1000 pixels. If it is over 1000 pixels, user can change the projector installation location, lens shift adjustment, projector display aspect ratio or reduce overlap region by geometry alignment. c [9x5 Curved] will cut the horizontal image into 8 sections and the image in each section can be independently adjusted. In different output resolutions, there will be different pixel number in each section: XGA: 1024/8=128, WXGA: 1280/8=160, 1080p: 1920/8=240. Usually, [9x5 Curved] alignment is enough for most of the curved screen edge blending. d If the overlapped area between two adjacent projectors has the same or multiple number as above, the geometry alignment in overlap region will have less flexibility. User can increase or decrease one or two grids (32 or 64 pixels) in overlap area to increase the flexibility for accurate alignment between adjacent projectors. e Below figure is an example for [9x5 Curved] alignment in 1024 resolution: 25% overlap region: The adjusting points in projector A & B will be at the same position in overlap region If the overlap is 256 pixels (25%) in XGA resolution, total adjusting points in overlap region are 15. The adjusting points in projector A & B will be at the same position in overlap region. User will have less adjustment flexibility. If increasing two grids (64 pixels) to 320 overlap pixels, user can have 30 adjusting points to get more accurate geometry alignment. It can align the images from two projectors on curved screen with good quality without Gwarp PC Tool. 37.5% overlap region The adjusting points in projector A & B will be separated in overlap region and increase geometry alignment accuracy. 8

10 Recommended overlap pixels in different output resolution Below is the list for the accuracy of geometry adjustment in different overlap pixels: GeoBox output resolution 1920* * *768 Min. adjusting flexibility 240/480/ /480/ /384/512 Max. adjusting flexibility 352/608/ /256/384/416/544/ /320/448/ Projector settings and installation a Reset projector to default setting. b Disable dynamic color adjustment and DLP Brilliant color adjustment. c To disable Auto Alignment function if user wants to use VGA analog input signal to avoid image shift during projector switching ON/OFF process. d Disable Auto Keystone function. e Select a Display Mode with 2.2 gamma curve will reduce the color difference in overlap area. User needs to test with different Display Mode setting based at final color fine-tune stage. f Use projector internal color adjusting function to adjustment the color variation among projectors before implement edge blending. g Install projectors at a place with image size that just can cover required image area and with minimize keystone to get better video quality. 4.7 GeoBox Settings a Reset GeoBox to default setting. b Select correct input port. c Select output resolution to be the same as projector native display resolution. d Check input/output LED indicators in each channel and make sure to have correction system connection. 4.8 Geometry alignment by OSD menu (Use [4 CORN] & [WARP] hotkeys) 9

11 a Please be familiar with OSD operation from front panel and remote controller, including activate grid pattern, channel selection and shortcut keys for [2x2], [Warp], [Video Wall], [Edge Blend] and [Info]. b [OSD Time Out] is default to 0. It will ensure the grid pattern will not be turned off automatically. Input mode change will disable OSD and grid pattern. c User can install IR extender receiver near each projector for easy GeoBox operation. If multiple units of GeoBox are used and IR receivers are put together, please set [Box ID] for each G-602 so that user can control each G-602 separately through [85x] command. Press number keys in Remote Controller following OSD menu for the control of multiple GeoBox: 850: simultaneous control for all GeoBox 851: control GeoBox ID No : control GeoBox ID No. 3 d Use [Pattern] & [CH 1-4] hot key to show grid patterns in all projectors. Press [Pattern] key again will change grid color. To set two different pattern colors in adjacent projectors will be more convenient during geometry alignment. e Please follow the sequence [2x2] [3x3] [5x3] [9x5] to do geometry alignment to ensure entire image will have uniform scaling factor. f Apply [2X2 Corner] geometry alignment and draw the corners to expected locations. It doesn t matter to have some image inside the screen once it covers entire screen before 4 corner adjustment. [Warp] alignment will adjust the image position back to the required position. g Apply [3x3 Curved] geometry alignment to let 9 adjusting points be located at the required position including four corners, edge center points and center line position. h Please use [5X3] & [9x5] for further geometry alignment and fine-tune. After finish the alignment, user can use [2x2] for complete image position fine tune. If user executes [3x3] alignment again after [9x5] alignment, [9x5] grid position will be reset and only keep [3x3] grid point information. i In ideal condition, all grids in edge blending area between two adjacent projectors should be aligned together. In some special case, the vertical lines in edge blending area have some gap and can t match 100%. User can adjust [Overlap] value in video wall settings to compensate this deviation and keep reasonable image quality. 10

12 j After the above processes, if the grid pattern in edge blending area still can t stack together, user can re-align overlap pixels to get more accurate geometry alignment result (see Sect. 4.5) or use [Gwarp] PC tool to apply 17x17 grid point adjustment. k Geometry alignment range from remote controller can be up to 300 pixels in [2x2] pixels more in [3x3] for one corner/edge. If more geometry alignment range is required, please use Gwarp PC tool to do geometry alignment. PC tool will double the alignment range. l If user finds the grid size between adjacent projectors is different. It means the projection image sizes between two projectors are different. Please measure the difference and try to make them have the same dimensions. 4.9 [Video Wall] settings (use [V.WALL] hotkey) After geometry alignment, it is required to capture image for each projector. a Click [INFO] to check if correct input and output timing modes are set in the system. If no input signal is connected, the system will assume the input signal is the same as output signal during Overlap value setting. User needs to apply this input/output timing for Overlap Value calculation. b [Video wall] settings for three projector horizontal edge blending as example [Zoom]: all GeoBox set to H=3, V=1 [Pan]: LH projector (1 st ): H=1, Center projector (2 nd ): H=2, RH projector (3 rd ): H=3 [Overlap]: select the right edge and apply the value calculated from Excel file LH projector: RH edge, Center projector: both RH/LH edges, RH projector: LH edge For dual projector edge blending, user can use below equation to calculate overlap pixel. Assumption: Input signal:1080p, Output to projector: XGA, Overlap 224 pixels (7 grids) Overlap value= (1920/2)/( /2)x(224/2)=118 pixels. User can also adjust [Overlap] value simultaneously and see the image in edge blending area comes closer till without double image. Two projectors shall have the same value. The difference shall not be over 2 pixels. c If user still sees some blurred image in edge blending area, please increase or decrease [Overlap] value in [Video Wall] setting to improve video quality. If the adjusting value is more than 1, please divide this value for adjacent projectors. For example, if the value should be 2 in center projector LH edge, then please add 1 in RH edge of the 1st projector and 1 in 2nd projector LH edge. 11

13 4.10 [Edge Blend] setting (use [E.BLEND] hotkey) a Select correct Edge for the edge blending: LH projector: RH edge, Center projector: RH & LH edge, RH projector: LH edge b RED and GREEN color indicating lines will appear when increase edge blending pixels. c User needs to adjust the color indicating lines to match together (green to green, red to red) and will see the final result Overlap region gamma correction (under [Edge Blend] menu) a Please activate [Gamma] sub-menu under [Edge Blend], select [Transition] and change the [Gamma] value to get the optimized video quality. b [Gain] menu next to [Gamma] can do further gamma curve change in each projector. It is to do further edge blending area color fine-tune. User will see significant improvement when each projector has different gamma curve. c If there is still some color difference, please try to change projector Display Mode first. If it is still can t fix the issue, user can do further color adjustment in projectors or use [Color] sub-menu under [Edge Blend] menu to adjust individual projector color Black level uplift ([Offset] adjustment under [Edge Blend] menu) a If the ambient light is dark, audience will see grey region in Edge Blending area. It is due to light leakage from projector optical system. Low contrast ratio projector will be more serious. Please apply [Offset] menu to uplift the color in non-transition area and [Corner] menu to do accurate position alignment. b Under [Offset] menu, user can try [Gain] and [Offset] color compensation to let non-transition and edge blending area to have the same color. After this step, user may see grey strips near the borders of edge blending area. User can use [Corner] to ship the position and eliminate these grey bars. 12

14 4.13 Image quality fine-tuning a The final performance will be a combination of many factors projector characteristics, projector setting, screen, ambient light and GeoBox setting. b Banding in overlap area under dark environment is caused by light leakage in the projector optic system. It is not possible to be fixed by signal manipulation. The only way is to raise the black level in none transition area through [Offset] menu. c GeoBox edge blending default setting is for projector with 2.2 gamma settings. To select projector display mode near 2.2 gamma setting will get the best result. d The projector may retain light leakage near the border of the imager (micro display DMD or LCD). It is not possible to be fixed. e The factors affect final image quality i. GeoBox settings: Edge Blending settings: Gamma, gain, Offset, Color Image Properties: To select Preset Mode to Neutral, srgb or Bluish Individual projector color adjustment [Color] function under [Edge Blend] menu. ii. Projector: To adjust image position of the projector and reduce keystone angle. Increase Overlap region & reduce off axis angle To change Display Mode, usually Standard, srgb/neutral will get better result. To disable projector Brilliant color adjustment or Dynamic color adjustment. Try different color settings in the projectors. iii. Screen: To use lower gain value screen. Short throw projectors with high gain screen will have color difference in different viewing angle and cause different overlap area banding from difference viewing angles System power ON/OFF setting a User can access [Options] [Accessibility] [Standby Time Out] to do automatic System Power ON/OFF setting by the control of signal source. b If the time is set to 60, GeoBox will automatically turn off output signals when no input signal is detected for 60 seconds. c If the projector can also automatically shut down when no input signal is detected. User can control signal source to turn ON/OFF the system. 13

15 d If the time is set to [Off], user needs to do manual Power ON/OFF in the system as default Enable [Black Screen] while no input signal or mode change a The default screen color when no input signal is detected or during input timing change is Blue. b User can set it into Black color by below OSD operations: [Options] [Accessibility] [Black Screen] [Enable] Save all settings into [Profile] [Index] a Activate [Profile] sub-menu under [Options] [Settings] to save the final settings. User can save up to 5 different display profiles. b User needs to save each channel settings separately. c User can recall Profile settings for all channels at the same time through click [CH A/B] [Profile] select [index #] by number key (can t be selected by Arrow key). d After finish all the procedures, please power off and power on the system again to check if the result is the same as expected without change. If any position shift is found, please check if Gwarp value had been properly download into GeoBox. e EDID settings in different input port will be also saved into [Profile] 4.17 Thermal drift in projector image position Projector will have some image position shift in different working temperature. Image position will be not stable at the first minutes after power on. During this period, user many see some image position shift in overlap area. This is called thermal drift. Different projectors may have different phenomenon. The range for image thermal drift may be up to 5mm PC output resolution setting If PC is used as signal source for Microsoft Office, please select the right output resolution. Too high output resolution may cause blurred image in text. 1280x800 or 1366x768 output resolution is good for two projector edge blending system. 5 Geometry alignment by Gwarp2 PC tool Use USB cable to connect PC USB port with GeoBox USB type B port. Gwarp2 is HID interface and no driver is required. User can select different language for the operation. Uniformity adjustment function is not inside OSD menu. If user wants to implement this function, user needs to use Gwarp2. Please see more details in [Gwarp2 user guide]. User can download from our website. Please contact us for any question. 14

16 (1) : Open Gwarp2.exe software in PC and click [Connect] (1) to link PC with GeoBox. (2) : User will see [DisConnect] (1) and GeoBox output resolution in (2) after connection. (3) : Select preferable Language (3). (4) : Select [CH #] for the operation. (5) : [Warp Adjust] (5): for geometry alignment [Pattern] (6): Open Grid pattern with different color Select mode (7) for adjustment (keyboard hotkey [CTRL + M]) Select [Change step] (8) for adjusting step. Select [Adjust Point] (9) (Keyboard hotkey [CTRL + Arrow keys]) Control point geometry adjustment (10) (keyboard hotkey [Arrow keys]) Mode [2x2] to draw the location for 4 corners to the desired locations. Mode [3x3] to adjust image center point and edge center points to the expected locations. To use other grid patterns to do further geometry alignments. Please follow the step [2x2] [3x3] [5x5] [9x9] [17x17]. When [17x17] is executed and return to [5x5] adjustment, only the values at same control points as [5x5] will be reserved. User can return to [2x2] for final adjustment and the curve adjustment result will not be reset. (11) : Up to this stage, the geometry result is stored in PC only. User needs to load the adjustment result to GeoBox through below procedures: To select # key to save the result to Gwarp Pro #. (11) User can check the result through OSD menu: [Anyplace] [Gwarp Pro] [UserMap #] [OK] User can fine-tune Gwarp2 result through [Fine-tune] menu under [Gwarp Pro] menu. The adjusting range is +_ 50 pixels in each corner. When fine-tune 4 corners, if will not affect curve adjustment result. 15

17 (12) : If user wants to save geometry alignment result in PC, please click [Save setting] (12). Only geometry setting data will be saved. (13) : Select [Video Wall] (13) to implement video wall setting through Gwarp2. It is the same function as operated by IR remote controller. (14) : Select [Edge Blend] (14) to implement Edge Blend setting through Gwarp2. It is the same function as operated by IR remote controller. (15) : Select [Uniformity] (15) to do color uniformity setting through Gwarp2. IR remote controller doesn t have this function. (16) : User can save the final result into Profile (16). It will save all the settings conducted in Gwarp2. Before save to Profile, user needs to save [Warp Adjust] and [Uniformity] adjustment into Gwarp Pro (11) first. Otherwise the result will be not saved into Profile. User can recall Profile settings and modify in the future. However, modification in geometry result can only be done by [Fine-tune] function under [Gwarp Pro] menu up to +_50 pixels in H&V directions. 6 Keyboard Hotkey for convenient Gwarp2 operation 6.1 System Reset a [CTRL + Shift + R]: Reset selected channel b [CTRL + Shift + A]: Reset all channels (from CH1-CH4) c Input/Output resolution and Profile Index settings will remain the same without reset 6.2 [Warp Adjust] a [M]: Change Adjust mode from [2x2] [3x3] [5x3] [5x5]... b [CTRL + Arrow]: Select control point c [Arrow]: adjust value (control point position) d [Shift + Arrow]: Geometry adjustment with 1 pixel/step e [P]: Enable grid pattern with different colors (R, G, B, C, M, W) f [CTRL + P]: Disable grid pattern 6.3 [Uniformity] adjustment a Click [Enable] to execute uniformity function b [Arrow] key to move control point to the location for uniformity adjustment c Set Uniformity value in GAIN [S]: to increase GAIN value with small step (about 0.001) [X]: to increase Gain value with large step (about 0.5) [A]: to decrease GAIN value with small step (about 0.001) [Z]: to decrease GAIN value with large step (about 0.5) d Set Uniformity value in Offset [F]: to increase GAIN value with small step (about 1) [V]: to increase Gain value with large step (about 10) [D]: to decrease GAIN value with small step (about 1) [C]: to decrease GAIN value with large step (about 10) 16

18 e [Space Bar]: Execute uniformity adjustment at current point and also copy the value f [L]: to download setting value to the point, need to press [Space Bar] to implement the result. g [CTRL + Arrow]: Continuously execute uniformity adjustment to the target points or region. h Example to set different locations with the same uniformity adjustment value Move [Arrow] to new position and set uniformity values Click [Space bar] to implement and copy the value Move [Arrow] to point A Press [L] to recall the value, then press [Space Bar] to implement the value to point A or [CTRL + Arrow] to implement to continuous points or region. Move [Arrow] to point B Press [L] to recall the value, then press [Space Bar] to implement the value to point B or [CTRL + Arrow] to implement to continuous points or region. i Example to copy uniformity settings value A to B Move [Arrow] to A Press [Space Bar] in keyboard to copy the value [Arrow] key to B Press [L] to download the value to point B Press [Space Bar] to implement A value to point B or press [CTRL + Arrow] to implement A value to continuous points. 7 [ALL]: OSD simultaneous control in all channels a. [All] function: Allows user to control all channels in simultaneously. When press [All] function key then functional hot key, the system will execute the same OSD command to all channels. b. [All] enable keys: Remote controller: [CH A/B] Front panel: [All] menu key c. LED Indicator: When [All] is activated, all channel LEDs on Front panel will show up. d. [All] function will be functional in the first level of OSD in below OSD menu for all channels. MUTE: enable/disable Audio Mute function EXIT: close all OSD MENU and grid pattern even each channel shows different OSD. INPUT: select input port OUTPUT: select output resolution 4 CORN: pop up 4 Corner geometry adjustment menu WARP: Curve alignment menu E.BLEND (Edge Blend): Edge Blending menu V.WALL (Video Wall): Video wall menu e. [All] function will be functional up to the second level of OSD, remote control as example: [CH A/B][INFO]: to show system information. If press [CH A/B] [EXIT] again, all the information will be close. 17

19 [CH A/B] [PATTERN]: Activate grid test PATTERN. User can press [CH A/B] key and press [Pattern] to change pattern color in all channels at the same time. [CH A/B][Profile]: To active [Profile Load] menu. All channels will show the same INDEX when follow [CH A/B] [Profile] [Number key] (don t select from OSD arrow key). Profile menu will show up for 5 seconds till the system finishing settings. User needs to store the same settings into the same Profile Index so that end user can select profile Index in all channels at the same time. Except for the above, all the other function only functional up to the first level of the OSD. All LED show-up [All] function key 8 [EDID] setting Selective EDID setting and programmable EDID function are added into GeoBox. a GeoBox can support big range of input signal timing from 1024x720 up to 4k/2k. In order to get the best video performance, user needs to select different input signal resolution. b Different PC display cards have different setting and behavier. Many users may not be able to do the right settings c High end media player or server can support big range of outputs from 720p to 4k/2k. If no EDID selection function, only one default EDID can be selected by media player. The system may not show the best video quality. d Different display modes may show different final image aspect ratio. User can ultilize different EDID setting to change input signal timing and get different output image aspect ratio. 18

20 custom Activate EDID setting menu: [Options] [Setting] [EDID] Use IR remote controller to select desired EDID. After select EDID, the PC or medial will automatically change the output timing setting. Press [INFO] key to check if the input and output timing are set correctly. User can also create any EDID timing through the menu [Custom]. The timing range are as follows: H: V: a Some PC may not follow EDID from GeoBox and show different result. If it happens, please open resolution setting window and select desired output from PC. b User can also set non-vesa standard output timings from PC, GeoBox can accept this kind of output timing under the conditions that the maximum clock rate shall be under 330MHz and the resolution shall not exceed 3840x System bandwidth and system crash Due to hardware bandwidth limitation, it is possible to see some abnormal image during some settings. It is due to processing bandwidth limitation. It may happen in below conditions: a. High resolution input source like 3840x2160 with different video wall ZOOM and Overlap settings. b. When the input is 4k/2k with image rotation or PIP/POP. c. When implement extreme geometry alignment. d. When implement active 3D 120Hz input/output. e. We suggest to select the image vertical resolution same as projector. If user uses 1280x800 projectors, then 3840x800 or 3840x1080 signal resolution should be selected to avoid the above bandwidth issue. f. Once it happens, please reset the system and select different settings. Once it normally display, no side effect will happen again. 10 Screen Selection a Gain value less than 1.5 will be recommended for Edge Blending application. Higher gain value will be more sensitive to color difference among projectors. In short throw projector edge blending, viewer may see different edge blending result while viewing at different angles. b Motorized screen position may be shifted from time to time. It will affect the image stacking in edge 19

21 blending area and may cause blurred image. Fixed screen is recommended. c If ultra-short throw ratio projector is used, the screen gain value should be under The flatness of the screen will be also more important in this kind of projector. 11 Projector Selection and settings a The projectors for the edge blending should be the same model and the same production lot. If they are not the same models, it may create some difficulty and performance issue. b Usually, higher contrast ratio in the projector will have better black level performance. The projector with contrast ratio more than 3000:1 is recommended for edge blending. In a dark environment, video projector with 10,000:1 contrast ration or higher will be better. This contrast ratio should be native contrast ratio but not dynamic contrast ratio. c If possible, please shut down Brilliant color and Dynamic auto color adjustments. They may affect edge blending result. d All the projectors shall have the same setting including optical zoom ratio, color temperature, color characteristics, lamp setting, display mode...etc. e Please select a display mode with the best performance. Usually, Standard or Native display mode will provide easier color fine tune. f Please select gamma 2.2 for edge blending. Different gamma settings and affect the video quality in overlap region. g The mechanical stability in optical system is important. It should be rigid with less thermal drift. h A projector with big ZOOM and lens shift will be more convenient for the installation. i Throw ratio will affect installation distance, please select right one based on the installation space. j If ultra-short throw projector is used in curved screen, it will cause big image position shift and may also cause focus issue. Carpentry screen and curved screen are not recommended. 20

22 12 Specifications Input and Output interface Image geometry correction, warp, rotation (Anyplace function) Geometry alignment range Edge Blending Input in each channel 1x DualLink DVI-I 1x HDMI 1.4 input 1x DisplayPort 1.1a input All digital input ports support 2560x1600 and 3840x1080 at 60Hz Output in each channel 1x HDMI outputs for RH/LH channel up to 1x HDMI loop out port from HDMI input for daisy chain connection up to Compliant with HDCP 1.3 High-bandwidth Digital Content Protection Support programmable EDID & non-vesa standard input timings. Frame lock function for system synchronization. Full functions for 4 corner alignment, vertical and horizontal keystone correction, Pincushion / Barrel adjustment & image warp. Advanced Gwarp technology for precise geometry alignment & edge blending. Control two projectors with different geometry and processing settings. Internal grid pattern with selectable colors for easy geometry alignment. 2x2, 3x3, 5x3, 9x5 grid pattern geometry alignment through manual operation without PC via remote controller or front panel keypads. Up to 17x17 grid points geometry alignment through Gwarp PC tool. Users can see real time geometry alignment and get optimized result. Precise image cropping, resizing, positioning and aspect ratio adjustment. Free Gwarp PC tool is available for sophisticated geometry alignment. Under WXGA & 1920x1200 output resolutions, the adjustment range via IR remote controller are as follows: [2x2 Corner] adjustment in one side: H= 300 Pixels, V= 200 pixels [3x3 curved], [5x3 Curved] & [9x5] adjustment: H: 300 Pixels, V= 200 pixels Maximum adjustment range in one side: H= 600 Pixels, V= 400 pixels Maximum adjustment range in both side: H=1200 Pixels, V=800 pixels If apply Gwarp2 PC tool, the adjustment range will be double. Under XGA output resolution, the adjustment range will be only 50%. Edge blending in all edges up to 1000 pixels overlapped area. Execute 4 directions edge blending. Each unit controls up to 2 projectors and can be cascaded. Precise gamma correction in overlapped region to eliminate banding effect. Precise black level uplift to eliminate grey banding effect in edge blending area due to optical light leakage from the projector. Independent RGB gain and offset adjustment for white balance & color correction in each projector. Support edge blending with projector at portrait position. 21

23 Support multiple inputs edge blending for high end simulation and high resolution big scale display. Flexible display system: one 3x projector edge blending system can display discrete content, 2 (edge blended)+1 or All-in-one (3 edge blended) Support cylindrical screen and irregular curve screen edge blending. Color Uniformity adjustment in gain and offset across entire display is available. Minimum adjusting range is 64x64 pixels. Video Wall Edge blending in all edges up to 1000 pixels overlapped area. Execute 4 directions edge blending. Each unit controls up to 2 projectors and can be cascaded. Precise gamma correction in overlapped region to eliminate banding effect. Precise black level uplift to eliminate grey banding effect in edge blending area due to optical light leakage from the projector. Independent RGB gain and offset adjustment for white balance & color correction in each projector. Support cylindrical screen and irregular curve screen edge blending. Color Uniformity adjustment in gain and offset across entire display is available. Minimum adjusting range is 64x64 pixels. High end video processing and de-interlace 3D stereoscopic display PIP/POP (side by side) Image flip and rotation 10-bit 4:4:4 full sampling processing with 3D motion adaptive de-interlace, low angle algorithm (similar to Faroudja DCDi) and 3:2/2:2 movie mode detecting and recovery. True 10-bit data processing with high end scaling. 24Hz/50Hz-in / 24Hz/50Hz-out without frame repeat or loss. Auto decode 3D signals for passive 3D display, including signal source from Blue Ray, STB, game console, media player and PC. Auto decode Stereoscopic Player/ Nvidia 3D Vision 3D format and Blue Ray 1080p 24Hz 3D signal into 720p/XGA 120Hz signal for active 3D display. Support standard HDMI 1.4a 3D formats, including 1080p/24Hz full HD, Side by Side, Top-Bottom, frame sequential & Line interleaved (line by line). Support 3840x1080 Full HD Side by side 3D format and SONY 1080i/60Hz frame packed 3D. Zero latency in RH/LH eye image to get the most comfortable 3D. Precise geometry stacking alignment and allow 2D/3D in the same setup with clear image and OSD menu. 3D display can be on flat and curved screen. It can be expanded by more projector image stacking or edge blending. PIP/POP in each channels. PIP image with flexible size, position and aspect ratio. PIP/POP at portrait display. 3D motion adaptive de-interlace at PIP/POP images. Image 90/180/270 degrees rotation Image flip: Left/Right, Top/Bottom, Front/Rear Geometry alignment can implement small angle image rotation. Color adjustment Preset color: Standard, srgb, Reddish, Bluish 22

24 Aspect ratio Discrete RGB gain adjustment Brightness, contrast, hue, saturation, sharpness adjustment. White balance and color uniformity adjustment. All the above color adjustment will apply to the control channel only. Full screen or maintain input signal original aspect ratio. Switch between 2.35:1 & 16:9 aspect ratio Other aspect ratio can be changed by EDID setting and through Video Wall and Geometry adjustment function. System control and convenient features for system integrators Power consumption Warranty Weight Dimensions Reliable and durable design for 7/24 working condition. Programmable EDID resolution for optimized video quality. Full functional keypads, IR control, RS232 and optional Ethernet control. Gwarp PC tool is available to control GeoBox through USB. One PC tool can control 4 projectors simultaneously. ID # for each GeoBox. Convenient for system installation and control. Selectable Background color. 10 different geometry and color uniformity settings. 5 profile settings for flexible display modes. Automatic power ON/OFF through input signal control. System settings can be saved in PC or copy to other units. Max: 35W (G-704), 25W(G-703), 17W (G-702), 8.5W (G-106) External DC 12V/5A power supply 2 years Max. 2.8 Kg (G-704 body only) 440mmL x 190mmD x 60mmH 23

G-602 Quick User Guide

G-602 Quick User Guide Quick User Guide (Dual channel Universal/Curved Screen Edge Blender) Technical support: E-mail: sales@vnstw.com Tel: +886-2-8751-2785 Cell: +886-935-678-033 Skype: vns-inc Version: 3.01 Website: www.vnstw.com.tw

More information

G-106Ex Single channel edge blending Processor. G-106Ex is multiple purpose video processor with warp, de-warp, video wall control, format

G-106Ex Single channel edge blending Processor. G-106Ex is multiple purpose video processor with warp, de-warp, video wall control, format G-106Ex Single channel edge blending Processor G-106Ex is multiple purpose video processor with warp, de-warp, video wall control, format conversion, scaler switcher, PIP/POP, 3D format conversion, image

More information

G-106 GWarp Processor. G-106 is multiple purpose video processor with warp, de-warp, video wall control, format conversion,

G-106 GWarp Processor. G-106 is multiple purpose video processor with warp, de-warp, video wall control, format conversion, G-106 GWarp Processor G-106 is multiple purpose video processor with warp, de-warp, video wall control, format conversion, scaler switcher, PIP/POP, 3D format conversion, image cropping and flip/rotation.

More information

G-700LITELite multiple Channel warping processor

G-700LITELite multiple Channel warping processor G-700LITELite multiple Channel warping processor Version: 2.01, Date: 2017-07 G-700Lite is a warping processor with the ability to provide multiple processing modules to control from 1 to 4 projectors

More information

G406 application note for projector

G406 application note for projector G406 application note for projector Do you have trouble in using projector internal warp and edge blending function? Inconvenient in multiple signal source connection System resolution is not enough after

More information

2D/3D Multi-Projector Stacking Processor. User Manual AF5D-21

2D/3D Multi-Projector Stacking Processor. User Manual AF5D-21 2D/3D Multi-Projector Stacking Processor User Manual AF5D-21 Thank you for choosing AF5D-21 passive 3D processor. AF5D-21 is an advanced dual channel passive 3D processor with 10 bits high end scaler and

More information

The absolute opposite of ordinary. G804 Quad Channel Edge Blending processor

The absolute opposite of ordinary. G804 Quad Channel Edge Blending processor The absolute opposite of ordinary G804 Quad Channel Edge Blending processor Input: up to 4096*2160 @60hz 4:4:4 full color sampling Output: 2048*1080 @60Hz New generation Warp & Edge blending engine Technical

More information

G-303 Active/Passive 3D Processor Quick User Manual

G-303 Active/Passive 3D Processor Quick User Manual G-303 Active/Passive 3D Processor Quick User Manual G-303 is dual channel high end 10-bit processor with 3D motion adaptive de-interlace, low angle smooth algorithm and 3:2/2:2 film mode processing with

More information

The absolute opposite of ordinary

The absolute opposite of ordinary The absolute opposite of ordinary G408 4K/60 vido wall controller 2x HDMI 2.0 in, 8x FHD out 10-bit processor 4:4:4 Chroma sampling Independent rotation/ scaling/ cropping Also serve as two Quad channel

More information

The absolute opposite of ordinary

The absolute opposite of ordinary The absolute opposite of ordinary G406 4K/60 video wall controller with matrix function Support 8k/4k with pixel to pixel video quality 4 in/out in one box, DCi/UHD 4K60 in all inputs, 10-bit processor,

More information

The absolute opposite of ordinary

The absolute opposite of ordinary The absolute opposite of ordinary G406Lite 4K/60 video wall controller 1 in / 4 out in one box, HDMI 2.0 / HDCP 2.2 input up to DCi/UHD 4K/60 fps, 10-bit processor, 4:4:4 Chroma sampling, Independent rotation/

More information

G406 Quick User Guide

G406 Quick User Guide The absolute opposite of ordinary G406 Quick User Guide G406 4K/60 video wall controller with matrix SW function Technical support: E-mail: sales@vnstw.com Tel: +886-2-2792-2819 Cell: +886-935-678-033

More information

2D to 3D. Projector Stacking Warping Full HD 3D Edge Blending Video Wall Aspect Ratio Manipulation

2D to 3D. Projector Stacking Warping Full HD 3D Edge Blending Video Wall Aspect Ratio Manipulation Stacking Warping Full HD 3D Edge Blending Video Wall Aspect Ratio 2D to 3D Airflex5D is a professional 2D/3D multi-projector stacking processor designed to provide a user-friendly experience across a wide

More information

OPERATING GUIDE. HIGHlite 660 series. High Brightness Digital Video Projector 16:9 widescreen display. Rev A June A

OPERATING GUIDE. HIGHlite 660 series. High Brightness Digital Video Projector 16:9 widescreen display. Rev A June A OPERATING GUIDE HIGHlite 660 series High Brightness Digital Video Projector 16:9 widescreen display 111-9714A Digital Projection HIGHlite 660 series CONTENTS Operating Guide CONTENTS About this Guide...

More information

CONTENT Product Introduction... 2 Packing Configuration...3 Hardware Orientation... 4 Front Panel... 4 Back Panel... 6 Using Your Product... 7 Content

CONTENT Product Introduction... 2 Packing Configuration...3 Hardware Orientation... 4 Front Panel... 4 Back Panel... 6 Using Your Product... 7 Content VENUS X1PRO Quick Start 4K input support in DP, HDMI and DVI Input standard 2K formats Scale and switch seamlessly between 2K and 4K inputs Output to any format 2K or 4K EDID management on board HDCP 2.0

More information

HIGHlite Laser 3D Series High Brightness Digital Video Projector

HIGHlite Laser 3D Series High Brightness Digital Video Projector HIGHlite Laser 3D Series High Brightness Digital Video Projector 4INSTALLATION AND QUICK-START GUIDE 4CONNECTION GUIDE 4OPERATING GUIDE 4REFERENCE GUIDE 114-913C About This Document Follow the instructions

More information

HD Mate Scaler USER MANUAL.

HD Mate Scaler USER MANUAL. HD Mate Scaler USER MANUAL www.gefen.com ASKING FOR ASSISTANCE Technical Support: Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday through Friday

More information

VSP 516S Quick Start

VSP 516S Quick Start VIEWSIZE THE WORLD VSP 516S Quick Start Max 2048 1152@60Hz/2560 816 60Hz input/output resolution User customize output resolution 3G/HD/SD-SDI input Multiple cascade mapping for super resolution Seamless

More information

VSP 198CVS Quick Start

VSP 198CVS Quick Start VIEWSIZE THE WORLD VSP 198CVS Quick Start Max 2048 1152@60Hz/2560 1152 50Hz input/output resolution User customize output resolution 3G/HD/SD-SDI input Multiple cascade mapping for super resolution DVI

More information

HDMI Digital scaler with ultra high bandwidth ID#443

HDMI Digital scaler with ultra high bandwidth ID#443 HDMI Digital scaler with ultra high bandwidth ID#443 Operation Manual Introduction Congratulations on your purchase of the HDMI Digital scaler with ultra high bandwidth. The HDMI Digital scaler with ultra

More information

KRAMER ELECTRONICS LTD. USER MANUAL

KRAMER ELECTRONICS LTD. USER MANUAL KRAMER ELECTRONICS LTD. USER MANUAL MODEL: Projection Curved Screen Blend Guide How to blend projection images on a curved screen using the Warp Generator version K-1.4 Introduction The guide describes

More information

USER MANUAL. HIGHlite Laser 3D Series INSTALLATION AND QUICK-START GUIDE CONNECTION GUIDE OPERATING GUIDE REFERENCE GUIDE

USER MANUAL. HIGHlite Laser 3D Series INSTALLATION AND QUICK-START GUIDE CONNECTION GUIDE OPERATING GUIDE REFERENCE GUIDE HIGHlite Laser 3D Series High Brightness Digital Video Projector USER MANUAL INSTALLATION AND QUICK-START GUIDE CONNECTION GUIDE OPERATING GUIDE REFERENCE GUIDE 114-913B Digital Projection HIGHlite Laser

More information

USER MANUAL. 28" 4K Ultra HD Monitor L28TN4K

USER MANUAL. 28 4K Ultra HD Monitor L28TN4K USER MANUAL 28" 4K Ultra HD Monitor L28TN4K TABLE OF CONTENTS 1 Getting Started 2 Control Panel/ Back Panel 3 On Screen Display 4 Technical Specs 5 Care & Maintenance 6 Troubleshooting 7 Safety Info &

More information

VSP 9516S Quick Start

VSP 9516S Quick Start VIEWSIZE THE WORLD VSP 9516S Quick Start Max 2048 1152@60Hz/2560 816 60Hz input/output resolution User-defined resolution adjustment Picture in picture Audio and video sync Seamless switching between inputs

More information

USER MANUAL. HIGHlite Laser 3D Series INSTALLATION AND QUICK-START GUIDE CONNECTION GUIDE OPERATING GUIDE REMOTE COMMUNICATIONS GUIDE REFERENCE GUIDE

USER MANUAL. HIGHlite Laser 3D Series INSTALLATION AND QUICK-START GUIDE CONNECTION GUIDE OPERATING GUIDE REMOTE COMMUNICATIONS GUIDE REFERENCE GUIDE HIGHlite Laser 3D Series High Brightness Digital Video Projector USER MANUAL INSTALLATION AND QUICK-START GUIDE CONNECTION GUIDE OPERATING GUIDE REMOTE COMMUNICATIONS GUIDE REFERENCE GUIDE 114-913A Digital

More information

DP Tuner 80 Remote Control Software User Manual. Version:08 Issue Date:May 10, 2018

DP Tuner 80 Remote Control Software User Manual. Version:08 Issue Date:May 10, 2018 DP Tuner 80 Remote Control Software User Manual Version:08 Issue Date:May 10, 2018 Copyright Information Copyrights Lumens Digital Optics Inc. All rights reserved. Lumens is a registered trademark of Lumens

More information

Marshall Electronics. Pro A/V Communications VMV-402-SH. 3G/HD/SD-SDI Quad-viewer/Switcher with Audio Meter Display. User Manual.

Marshall Electronics. Pro A/V Communications VMV-402-SH. 3G/HD/SD-SDI Quad-viewer/Switcher with Audio Meter Display. User Manual. Marshall Electronics Pro A/V Communications VMV-402-SH 3G/HD/SD-SDI Quad-viewer/Switcher with Audio Meter Display User Manual Table of Contents 1. Introduction... 3 2. Features... 3 3. Package Contents...

More information

RMS 8424S Quick Start

RMS 8424S Quick Start VIEWSIZE THE WORLD RMS 8424S Quick Start Standard 4 unit rack mount size 8 inch LCD 2 1024 3 (RGB) 600 16:9 / 4:3 adjustable SDI/HDMI embedded audio output via 3.5mm earphone socket Support SDI/DVI audio

More information

DB-VRC4H 4K HDMI Compact Video Wall Controller with 45 degree screen rotation

DB-VRC4H 4K HDMI Compact Video Wall Controller with 45 degree screen rotation DB-VRC4H 4K HDMI Compact Video Wall Controller with 45 degree screen rotation The DigiBird DB-VRC4H Video Wall Controller is the simplest and most cost-effective solution to build an eyecatching and creative

More information

SC-HD-2A HDMI Scaler & Audio Embedder / Extractor

SC-HD-2A HDMI Scaler & Audio Embedder / Extractor User s Manual SC-HD-2A HDMI Scaler & Audio Embedder / Extractor Scale HDMI or DVI video Embed Digital or Analog Audio into HDMI output Extract (De-embed) Digital and Analog Audio from HDMI input UMA1246

More information

VSP 168HD Quick Start

VSP 168HD Quick Start VSP 168HD Quick Start Support 10Gbps of transmission rate Support HDBaseT protocols and standards Support USB upgrade Max 2048 1152@60Hz/2560 816 60Hz input/output resolution Support custom output resolution

More information

PLL2210MW LED Monitor

PLL2210MW LED Monitor PLL2210MW LED Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Safety Precautions...2 First Setup...3 Front View of the Product...4 Rear View of the Product...5 Quick Installation...6

More information

HIGHlite 660 3D Series High Brightness Digital Video Projector

HIGHlite 660 3D Series High Brightness Digital Video Projector HIGHlite 660 3D Series High Brightness Digital Video Projector 4INSTALLATION AND QUICK-START GUIDE 4CONNECTION GUIDE 4OPERATING GUIDE 4REFERENCE GUIDE 114-242E About This Document Follow the instructions

More information

VENUS X1PRO-E Quick Start

VENUS X1PRO-E Quick Start VENUS X1PRO-E Quick Start 4K input support in DP, HDMI and Dual Link DVI Support 8K x 1K, 4K x 2K Seamless Splicing EDID management Modular 2K input: Three slots for 2K input options 2K-2K and/or 4K-2K

More information

Click to Print This Page. 9,500 ANSI / 10,500 ISO Lumens Contrast Ratio: 10,000:1 (Dynamic Black) 1,000:1 native Part Number:

Click to Print This Page. 9,500 ANSI / 10,500 ISO Lumens Contrast Ratio: 10,000:1 (Dynamic Black) 1,000:1 native Part Number: Digital Projection Projector Specification Click to Print This Page Specification Sheet E-Vision Laser 0K 9,500 ANSI / 0,500 ISO Lumens Contrast Ratio: 0,000: (Dynamic Black),000: native Part Number: 8-060

More information

DVI Digital scaler with ultra high bandwidth ID#442

DVI Digital scaler with ultra high bandwidth ID#442 DVI Digital scaler with ultra high bandwidth ID#442 Operation Manual Introduction Congratulations on your purchase of the DVI Digital scaler with ultra high bandwidth. Please read this to become familiar

More information

TFT LCD MONITOR USER MANUAL. L80AP and L101AP

TFT LCD MONITOR USER MANUAL. L80AP and L101AP TFT LCD MONITOR USER MANUAL L80AP - 8.0 and L101AP - 10.1 Table Of Contents Table of contents/ Warning.... 2 Precautions...3 About this user manual and products / Items included in the delivery..... 4

More information

T2210HD/T2210HDA 21.5 Wide-Screen LCD Monitor User Manual

T2210HD/T2210HDA 21.5 Wide-Screen LCD Monitor User Manual T2210HD/T2210HDA 21.5 Wide-Screen LCD Monitor User Manual Table of Contents Package contents...3 Installation...4 To connect the monitor to your PC... 4 Adjusting your monitor...5 Functions of the buttons

More information

22" Touchscreen LED Monitor USER'S GUIDE

22 Touchscreen LED Monitor USER'S GUIDE 22" Touchscreen LED Monitor USER'S GUIDE Content Operation Instructions...1 Unpacking Instructions...2 Safety Precautions...2 Front View of the Product...3 Rear View of the Product...4 Quick Installation...5

More information

SC-CSV-HDMI Composite & S-Video To HDMI Video Processor

SC-CSV-HDMI Composite & S-Video To HDMI Video Processor SC-CSV-HDMI Composite & S-Video To HDMI Video Processor UMA1173 Rev. NC CUSTOMER SUPPORT INFORMATION Order toll-free in the U.S. 800-959-6439 FREE technical support, Call 714-641-6607 or fax 714-641-6698

More information

USER MANUAL. 27 Full HD Widescreen LED Monitor L27ADS

USER MANUAL. 27 Full HD Widescreen LED Monitor L27ADS USER MANUAL 27 Full HD Widescreen LED Monitor L27ADS TABLE OF CONTENTS 1 Getting Started 2 Control Panel/ Back Panel 3 On Screen Display 4 Technical Specs 5 Care & Maintenance 6 Troubleshooting 7 Safety

More information

High-Definition Scaler. GTV-HIDEFS. User Manual

High-Definition Scaler.  GTV-HIDEFS. User Manual High-Definition Scaler GTV-HIDEFS User Manual www.gefentv.com Technical Support: Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday.

More information

Acer Home Series Projectors H9500BD

Acer Home Series Projectors H9500BD Acer Home Series Projectors H9500BD Product Highlights Exceptional home entertainment Acer H9500BD 2 Acer projector family Acer projectors offer exceptional color performance for all content, in any type

More information

26 Inch CGA/EGA/VGA/DVI to WXGA/1080p LCD - ID#703

26 Inch CGA/EGA/VGA/DVI to WXGA/1080p LCD - ID#703 26 Inch CGA/EGA/VGA/DVI to WXGA/1080p LCD - ID#703 Operation Manual Introduction This monitor is an open frame LCD Panel monitor. It features the VESA plug & play system which allows the monitor to automatically

More information

PL2410W LCD Monitor USER'S GUIDE.

PL2410W LCD Monitor USER'S GUIDE. PL2410W LCD Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Safety Precautions...2 First Setup...3 Front View of the Product...4 Rear View of the Product...5 Quick Installation...6

More information

PT-LW330 S P E C F I L E. LCD Projectors. As of April Specifications and appearance are subject to change without notice. 1/9.

PT-LW330 S P E C F I L E. LCD Projectors. As of April Specifications and appearance are subject to change without notice. 1/9. S P E C F I L E Product Number : Product Name : LCD Projectors As of April 2014. Specifications and appearance are subject to change without notice. 19 Specifications Main unit Power supply Power consumption

More information

Durable and Reliable Design for 24/7 Use. Overview. Narrow Bezel Optimized for Video Walls. 42 Narrow bezel commercial LED display

Durable and Reliable Design for 24/7 Use. Overview. Narrow Bezel Optimized for Video Walls. 42 Narrow bezel commercial LED display Durable and Reliable Design for 24/7 Use 42 Narrow bezel commercial LED display Overview The ViewSonic CDP4260-L is a 42 (42 viewable) commercial LED display designed for use 24 hours a day, 7 days a week.

More information

PRO-ScalerHD2V HDMI to VGA & Audio Scaler Converter. User s Guide. Made in Taiwan

PRO-ScalerHD2V HDMI to VGA & Audio Scaler Converter. User s Guide. Made in Taiwan PRO-ScalerHD2V HDMI to VGA & Audio Scaler Converter User s Guide Made in Taiwan Congratulations for owning a gofanco product. Our products aim to meet all your connectivity needs wherever you go. Have

More information

USER MANUAL. 22" Class Slim HD Widescreen Monitor L215DS

USER MANUAL. 22 Class Slim HD Widescreen Monitor L215DS USER MANUAL 22" Class Slim HD Widescreen Monitor L215DS TABLE OF CONTENTS 1 Getting Started Package Includes Installation 2 Control Panel / Back Panel Control Panel Back Panel 3 On Screen Display 4 Technical

More information

DCL9AW. User Manual. English

DCL9AW. User Manual. English DCL9AW User Manual English PRECAUTIONS Information for users applicable in European Union countries 1 Information for users applicable in United States of America 1 Installation 1 Power connection 1 Maintenance

More information

SCHD24K 4K UHD + HDMI to HDMI Scaler

SCHD24K 4K UHD + HDMI to HDMI Scaler SCHD24K 4K UHD + HDMI to HDMI Scaler Operation Manual DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. Ampronix assumes no responsibility for any infringements

More information

PXL2470MW LED LCD Monitor

PXL2470MW LED LCD Monitor PXL2470MW LED LCD Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Unpacking Instructions...2 Safety Precautions...2 Package Overview...3 First Setup...4 Front View of the Product...5

More information

Multi-format to HDMI scaler ID#15107

Multi-format to HDMI scaler ID#15107 Multi-format to HDMI scaler ID#15107 Operation Manual Introduction The Digital Video Scaler has CV, SV, HD, Composite, PC, HDMI and SDI inputs and can scale the signal into HDMI, VGA with audio output

More information

User Manual MODEL: KK1500-TR. Touch Display LCD Monitor. Installation Guide. 15 Resistive Touch LCD Monitor

User Manual MODEL: KK1500-TR. Touch Display LCD Monitor. Installation Guide. 15 Resistive Touch LCD Monitor Touch Display LCD Monitor User Manual Installation Guide 15 Resistive Touch LCD Monitor MODEL: KK1500-TR i-tech Company LLC TOLL FREE: (888) 483-2418 EMAIL: info@itechlcd.com WEB: www.itechlcd.com User

More information

HIGHlite 740 Series High Brightness Digital Video Projector

HIGHlite 740 Series High Brightness Digital Video Projector HIGHlite 740 Series High Brightness Digital Video Projector 4INSTALLATION AND QUICK-START GUIDE 4CONNECTION GUIDE 4OPERATING GUIDE 4REFERENCE GUIDE 114-751I About This Document Please follow the instructions

More information

User Manual MODEL: KKF1500-PCAP. True FLAT P-CAP LCD Monitor. Installation Guide. 15 True FLAT P-CAP Touch LCD Monitor

User Manual MODEL: KKF1500-PCAP. True FLAT P-CAP LCD Monitor. Installation Guide. 15 True FLAT P-CAP Touch LCD Monitor True FLAT P-CAP LCD Monitor User Manual Installation Guide 15 True FLAT P-CAP Touch LCD Monitor MODEL: KKF1500-PCAP i-tech Company LLC TOLL FREE: (888) 483-2418 EMAIL: info@itechlcd.com WEB: www.itechlcd.com

More information

Specifications LED Display Video Controller VX4. Xi an NovaStar Tech Co., Ltd. Rev1.0.4 NS

Specifications LED Display Video Controller VX4. Xi an NovaStar Tech Co., Ltd. Rev1.0.4 NS Specifications LED Display Video Controller VX4 Rev1.0.4 NS160110153 General Feature The VX4 is a professional LED display controller. Besides the function of display control, it also features in powerful

More information

Multi-Format AV Scaler with DisplayPort

Multi-Format AV Scaler with DisplayPort AVSC-7DA-HDMI Product Data Sheet Multi-Format AV Scaler with DisplayPort Basic Features Compliant with HDCP 2.0. Input support: Analog: analog video, S-Video, composite video, VGA; Digital: DVI, HDMI,

More information

photo by courtesy of Christiaan Beukes - Sphere Custom Design, RSA FORCE SERIES XXL HOME THEATRES VIDEO-PROJECTORS FOR

photo by courtesy of Christiaan Beukes - Sphere Custom Design, RSA FORCE SERIES XXL HOME THEATRES VIDEO-PROJECTORS FOR photo by courtesy of Christiaan Beukes - Sphere Custom Design, RSA FORCE SERIES VIDEO-PROJECTORS FOR XXL HOME THEATRES The FORCE SERIES are powerful 3-DLP video-projectors dedicated to elite home-cinema

More information

CSC K UHD+ HDMI and PC/HD to HDMI Scaler

CSC K UHD+ HDMI and PC/HD to HDMI Scaler CSC-6011 4K UHD+ HDMI and PC/HD to HDMI Scaler Operation Manual DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility

More information

DVI/PC/HD to DVI/PC Scaler - ID# 15320

DVI/PC/HD to DVI/PC Scaler - ID# 15320 DVI/PC/HD to DVI/PC Scaler - ID# 15320 Operation Manual Introduction This DVI/PC/HD to DVI/PC Scaler is capable of scaling and sourceswitching from PC (VGA), Component Video (SD/HD) and DVI input signals

More information

Video wall Precautions when moving and handling. Precaution. Please adhere to the warning signs printed on the box.

Video wall Precautions when moving and handling. Precaution. Please adhere to the warning signs printed on the box. Video wall Precaution 4-1. Precautions when moving and handling Please adhere to the warning signs printed on the box. Model: 47WV30MS 47WV30BR 47WV30BS 47WV30-BAAM 47WV30-BAAL 47WV50BR 47WV50MS 47LV35A

More information

PC/HDTV 2-Way Converter

PC/HDTV 2-Way Converter Vision for Net Media HDView PC/HDTV 2-Way Converter Operation Manual 1. Introduction The HDView is a high-performance universal PC/HDTV to PC/HDTV converter. It combines the functions of a video scaler,

More information

G3 NET 2K USER MANUAL

G3 NET 2K USER MANUAL G3 NET 2K USER MANUAL Article No: RGB-RD-UM-G3 NET 2K E001 Revision No: V1.0 CONTENTS CONTENTS... 1 Declarations... 3 FCC/Warranty... 3 Operators Safety Summary... 4 Installation Safety Summary... 4 Chapter

More information

PT-LB300 S P E C F I L E. LCD Projectors. As of April Specifications and appearance are subject to change without notice. 1/8.

PT-LB300 S P E C F I L E. LCD Projectors. As of April Specifications and appearance are subject to change without notice. 1/8. S P E C F I L E Product Number : Product Name : As of April 2014. Specifications and appearance are subject to change without notice. 18 Specifications Main unit Power supply Power consumption LCD panel

More information

USER MANUAL. 27" 2K QHD LED Monitor L27HAS2K

USER MANUAL. 27 2K QHD LED Monitor L27HAS2K USER MANUAL 27" 2K QHD LED Monitor L27HAS2K TABLE OF CONTENTS 1 Getting Started 2 Control Panel/ Back Panel 3 On Screen Display 4 Technical Specs 5 Troubleshooting 6 Safety Info & FCC warning 1 GETTING

More information

Ultra-short-throw projectors with connectivity for the BYOD classroom.

Ultra-short-throw projectors with connectivity for the BYOD classroom. SPECIFICATION SHEET PowerLite Ultra-short-throw 3LCD Projectors 570 XGA Resolution 575W WXGA Resolution 580 XGA Resolution Ultra Bright 585W WXGA Resolution Ultra Bright PowerLite 585W shown Projectors

More information

ASSEMBLY AND CALIBRATION

ASSEMBLY AND CALIBRATION CineMax Kit ASSEMBLY AND CALIBRATION www.cineversum.com Ref: T9003000 Rev: 01 Part. No.: R599766 Changes CineVERSUM provides this manual as is without warranty of any kind, either expressed or implied,

More information

TFT LCD MONITOR USER MANUAL HMDE Series 104AV-HMDE 121AV-HMDE 151/152AV-HMDE 156AV-HMDE, 171/172AV-HMDE 185AV-HMDE 191/192AV-HMDE 215AV-HMDE

TFT LCD MONITOR USER MANUAL HMDE Series 104AV-HMDE 121AV-HMDE 151/152AV-HMDE 156AV-HMDE, 171/172AV-HMDE 185AV-HMDE 191/192AV-HMDE 215AV-HMDE TFT LCD MONITOR USER MANUAL HMDE Series 104AV-HMDE 121AV-HMDE 151/152AV-HMDE 156AV-HMDE, 171/172AV-HMDE 185AV-HMDE 191/192AV-HMDE 215AV-HMDE 220AV-HMDE 236AV-HMDE 240AV-HMDE 270AV-HMDE 320AV-HMDE 420AV-HMDE

More information

PXL2760MW LED LCD Monitor

PXL2760MW LED LCD Monitor PXL2760MW LED LCD Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Safety Precautions...2 Package Overview...3 First Setup...4 Front View of the Product...5 Rear View of the Product...6

More information

USER MANUAL. VP-426 HDMI-PC Scaler MODEL: P/N: Rev 4.

USER MANUAL. VP-426 HDMI-PC Scaler MODEL: P/N: Rev 4. USER MANUAL MODEL: VP-426 HDMI-PC Scaler P/N: 2900-300277 Rev 4 www.kramerav.com Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 2.2 Safety Instructions 2 2.3 Recycling

More information

LCD VALUE SERIES (32 inches)

LCD VALUE SERIES (32 inches) LCD VALUE SERIES (32 inches) http://www.orionimages.com All contents of this document may change without prior notice, and actual product appearance may differ from that depicted herein 1. SAFETY INSTRUCTION

More information

19 / 20.1 / 22 WIDE SCREEN TFT-LCD MONITOR

19 / 20.1 / 22 WIDE SCREEN TFT-LCD MONITOR 19 / 20.1 / 22 WIDE SCREEN TFT-LCD MONITOR V193/ V220 Series V202 Series USER MANUAL www.viewera.com Rev. 2.0 Table of Contents EMC Compliance......1 Important Precautions...2 1. Package contents....3

More information

PT-TW340 S P E C F I L E. LCD Projectors. As of May Specifications and appearance are subject to change without notice. 1/8.

PT-TW340 S P E C F I L E. LCD Projectors. As of May Specifications and appearance are subject to change without notice. 1/8. S P E C F I L E Product Number : Product Name : LCD Projectors As of May 2014. Specifications and appearance are subject to change without notice. 18 Specifications Main unit Power supply Power consumption

More information

The Extron MGP 464 is a powerful, highly effective tool for advanced A/V communications and presentations. It has the

The Extron MGP 464 is a powerful, highly effective tool for advanced A/V communications and presentations. It has the MGP 464: How to Get the Most from the MGP 464 for Successful Presentations The Extron MGP 464 is a powerful, highly effective tool for advanced A/V communications and presentations. It has the ability

More information

USER MANUAL. 27 Full HD Widescreen LED Monitor L270E

USER MANUAL. 27 Full HD Widescreen LED Monitor L270E USER MANUAL 27 Full HD Widescreen LED Monitor L270E TABLE OF CONTENTS 1 Getting Started 2 Control Panel/ Back Panel 3 On Screen Display 4 Technical Specs 5 Care & Maintenance 6 Troubleshooting 7 Safety

More information

HTE Owner s Manual. HDMI, RS-232, IR & Ethernet Extender over HDBaseT with 3D, 4K, POE Support

HTE Owner s Manual. HDMI, RS-232, IR & Ethernet Extender over HDBaseT with 3D, 4K, POE Support HTE Owner s Manual HDMI, RS-232, IR & Ethernet Extender over HDBaseT with 3D, 4K, POE Support HTE Tx HTE Rx PureLink TM 535 East Crescent Ave Ramsey, NJ 07446 Tel: 201.488.3232 Fax: 201.621.6118 Website

More information

J6 User Manual. User Manual. Multi-Screen Splicing Processor J6. Xi an NovaStar Tech Co., Ltd. Rev1.0.1 NS

J6 User Manual. User Manual. Multi-Screen Splicing Processor J6. Xi an NovaStar Tech Co., Ltd. Rev1.0.1 NS J6 User Manual User Manual Multi-Screen Splicing Processor J6 Rev1.0.1 NS160110162 Statement Dear users, You are welcome to use the J6, a multi-screen splicing processor of Xi'an NovaStar Tech Co., Ltd.

More information

USER MANUAL Full HD Widescreen LED Monitor L236VA

USER MANUAL Full HD Widescreen LED Monitor L236VA USER MANUAL 23.6 Full HD Widescreen LED Monitor L236VA TABLE OF CONTENTS 1 Getting Started 2 Control Panel/ Back Panel 3 On Screen Display 4 Technical Specs 5 Care & Maintenance 6 Troubleshooting 7 Safety

More information

USER MANUAL Full HD Widescreen LED Monitor L215IPS

USER MANUAL Full HD Widescreen LED Monitor L215IPS USER MANUAL 21.5 Full HD Widescreen LED Monitor L215IPS TABLE OF CONTENTS 1 Getting Started 2 Control Panel/ Back Panel 3 On Screen Display 4 Technical Specs 5 Care & Maintenance 6 Troubleshooting 7 Safety

More information

WU515. A Powerful Performer. Geometry correction - 4 corner. x1.8 Zoom with vertical and horizontal lens shift. Horzontal and Vertical Keystone

WU515. A Powerful Performer. Geometry correction - 4 corner. x1.8 Zoom with vertical and horizontal lens shift. Horzontal and Vertical Keystone WU515 A Powerful Performer Geometry correction - 4 corner x1.8 Zoom with vertical and horizontal lens shift Horzontal and Vertical Keystone 6000 lumens WUXGA DLP projector WU515 Producing Full HD quality

More information

PC/HDTV to PC/HDTV converter (CP-251F)

PC/HDTV to PC/HDTV converter (CP-251F) PC/HDTV to PC/HDTV converter (CP-251F) Operation Manual This Converter has been especially modified to also accept RGsB Sync on Green Operation Controls and Functions Front Panel 1. Reset/ and +- The and

More information

User Manual. Multi-Screen Splicing Processor J6

User Manual. Multi-Screen Splicing Processor J6 User Manual Multi-Screen Splicing Processor J6 Rev1.0.0 NS160100147 Statement Dear users, Welcome to use the J6, a multi-screen splicing processor. This manual is intended to help you to understand and

More information

PT-TX400 S P E C F I L E. LCD Projectors. As of December Specifications and appearance are subject to change without notice.

PT-TX400 S P E C F I L E. LCD Projectors. As of December Specifications and appearance are subject to change without notice. S P E C F I L E Product Number : Product Name : LCD Projectors As of December 2015. Specifications and appearance are subject to change without notice. 18 Specifications Main unit Power supply Power consumption

More information

Specifications LED Display Video Controller VX4S

Specifications LED Display Video Controller VX4S Specifications LED Display Video Controller VX4S Rev1.0.3 NS160110155 General The VX4S is a professional LED display controller. Besides the function of display control, it also features in powerful front

More information

WU416. High resolution, compact and powerful. Bright WUXGA projector 4200 ANSI Lumens. Installation flexibility Vertical lens shift and 1.

WU416. High resolution, compact and powerful. Bright WUXGA projector 4200 ANSI Lumens. Installation flexibility Vertical lens shift and 1. WU416 High resolution, compact and powerful Bright WUXGA projector 4200 ANSI Lumens Installation flexibility Vertical lens shift and 1.6x zoom Ultimate Control - Full support for Crestron, Extron, AMX,

More information

900-Lumen Portable LED Projector Part #: User manual

900-Lumen Portable LED Projector Part #: User manual 900-Lumen Portable LED Projector Part #: 21797 User manual 900-Lumen LED Projector Manual Page 2 of 14 900-Lumen LED Projector Manual Page 3 of 14! SAFETY WARNINGS AND CAUTIONS WARNING: To reduce the risk

More information

Safety Information. Do Not

Safety Information. Do Not Safety Information Do Read, keep, and follow instructions. Heed all warnings. Turn off and unplug the power plug from the AC outlet before cleaning the unit. Use a soft dry cloth with mild detergent to

More information

CP-255ID Multi-Format to DVI Scaler

CP-255ID Multi-Format to DVI Scaler CP-255ID Multi-Format to DVI Scaler Operation Manual DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility

More information

USER MANUAL Full HD Widescreen LED Monitor L215ADS

USER MANUAL Full HD Widescreen LED Monitor L215ADS USER MANUAL 21.5 Full HD Widescreen LED Monitor L215ADS TABLE OF CONTENTS 1 Getting Started 2 Control Panel/ Back Panel 3 On Screen Display 4 Technical Specs 5 Care & Maintenance 6 Troubleshooting 7 Safety

More information

V9A01 Solution Specification V0.1

V9A01 Solution Specification V0.1 V9A01 Solution Specification V0.1 CONTENTS V9A01 Solution Specification Section 1 Document Descriptions... 4 1.1 Version Descriptions... 4 1.2 Nomenclature of this Document... 4 Section 2 Solution Overview...

More information

VENUS X1 USER MANUAL

VENUS X1 USER MANUAL VENUS X1 USER MANUAL Article No: RGB-RD-UM-X1 E001 Revision No: V1.5 CONTENTS CONTENTS... 1 Declarations... 3 FCC/Warranty... 3 Operators Safety Summary... 4 Installation Safety Summary... 4 Chapter 1

More information

Uni700 LCD Controller

Uni700 LCD Controller Landmark Technology Inc. Uni700 LCD Controller For TFT LCDs with Resolution up to 1,920 x 1,200 (Version A) January 27, 2009 1 1. Introduction The Uni700 controller board is designed for LCD panels of

More information

PT-LB382 S P E C F I L E. LCD Projectors. As of July Specifications and appearance are subject to change without notice. 1/9.

PT-LB382 S P E C F I L E. LCD Projectors. As of July Specifications and appearance are subject to change without notice. 1/9. S P E C F I L E Product Number : Product Name : LCD Projectors As of July 2015. Specifications and appearance are subject to change without notice. 19 Specifications Main unit Power supply Power consumption

More information

Ultra Short-throw Projectors <LV-WX300UST >

Ultra Short-throw Projectors <LV-WX300UST > Ultra Short-throw Projectors Outline of product This new ultra short-throw projector belongs to a class of DLP portable projectors that can be used in a wide variety of scenarios including

More information

15 Inch CGA EGA VGA to XGA LCD Wide Viewing Angle Panel ID# 833

15 Inch CGA EGA VGA to XGA LCD Wide Viewing Angle Panel ID# 833 15 Inch CGA EGA VGA to XGA LCD Wide Viewing Angle Panel ID# 833 Operation Manual Introduction This monitor is an open frame LCD Panel monitor. It features the VESA plug & play system which allows the monitor

More information

EH320USTi. 1080p ultra short throw interactive projection. TouchBeam finger touch interactive. Bright projection 4000 ANSI lumens

EH320USTi. 1080p ultra short throw interactive projection. TouchBeam finger touch interactive. Bright projection 4000 ANSI lumens EH320USTi 1080p ultra short throw interactive projection TouchBeam finger touch interactive Bright projection 4000 ANSI lumens Full HD 1080p resolution, 2x HDMI input and 16W audio Crestron RoomView RJ45

More information

12.1 Inch CGA EGA VGA SVGA LCD Panel - ID #492

12.1 Inch CGA EGA VGA SVGA LCD Panel - ID #492 12.1 Inch CGA EGA VGA SVGA LCD Panel - ID #492 Operation Manual Introduction This monitor is an open frame LCD Panel monitor. It features the VESA plug & play system which allows the monitor to automatically

More information

DU400. High resolution, compact and powerful. Bright WUXGA projector 4000 ANSI Lumens. Installation flexibility Vertical lens shift and 1.

DU400. High resolution, compact and powerful. Bright WUXGA projector 4000 ANSI Lumens. Installation flexibility Vertical lens shift and 1. DU400 High resolution, compact and powerful Bright WUXGA projector 4000 ANSI Lumens Installation flexibility Vertical lens shift and 1.6x zoom Ultimate Control - Full support for Crestron, Extron, AMX,

More information

INSTRUCTIONAL MANUAL FOR LCD ZOOM MICROSCOPE

INSTRUCTIONAL MANUAL FOR LCD ZOOM MICROSCOPE INSTRUCTIONAL MANUAL FOR LCD ZOOM MICROSCOPE ? 8 LCD Screen? 10.4 LCD Screen LCD Zoom Microscope Instruction Manual Please read the Instruction Manual carefully before installation and keep it for future

More information