Video Cassette Recorder VR960BPH. Hookup Pages. Important! Return your Warranty Registration Card within 10 days. See why inside.

Transcription

1 ideo Cassette ecorder 960BPH Hookup Pages mportant! eturn your Warranty egistration Card within 10 days. ee why inside.

2 75Ω 6 Hookups without a Cable Box The basic C/T connection antenna/cable to C to T is shown below. f you have a Cable Box or a irect Broadcast ystem, please refer to pages 8-9. After you hook up the C, please go to pages to turn on the C. 1isconnect the antenna or cable from your T. Antenna ndoor/utdoor (300 ohm) 75Ω Cable (75 ohm) ANTNNA Jack (on back of T) 2Connect the antenna or cable to the ANT(enna) Jack on the back of the C. Antenna ndoor/utdoor (300 ohm) ANT. F ANT. CH3 CH4 F Cable (75 ohm)

3 ANT. F 75 CH3 CH4 Hookups without a Cable Box (cont d) 7 3Connect the F coaxial cable (supplied) to the F Jack on the back of the C and to the ANTNNA Jack on the T. (You may use either a snap-on type or screw-on type of coaxial cable, whichever you prefer. A snap-on type is supplied.) Antenna or Cable ANT. 75 F F coaxial cable Antenna n Jack (on back of T) example only 4Plug in the T and the C. 5et the CH3/CH4 switch on the back of the C to CH3 or CH4, whichever channel is not used or least used in your area. To operate your C with your T, set the T to the same channel. For example, when playing a tape, if the CH3/CH4 switch is set to CH3, the T should be on channel 3. CH 4 or CH 3 CH3 / CH4 witch ANT. F ANT. F 6You are ready to turn on the C. Please go to pages before turning on the C.

4 8 Hookups with a Cable Box/irect Broadcast ystem There are two ways to connect your Cable Box/B to the C. With this connection: You may view any channel. You must select channels at the Cable Box/B. Channels cannot be changed at the C. You may not view a channel other than the one you are recording. You may not set up channels at the C. You can only program a timer recording for one channel at a time if you are not using the Controller. et the T and the C to the Cable Box/B output channel (channel 03 or 04); set the CH3/CH4 switch to the same channel. et your Cable Box/B to the channel you want to record. When you enter the channel you want to record in a timer recording, select channel 03 or 04 (the Cable Box/B output channel). (This is step 3 on page 40.) eave the Cable Box/B on for a timer recording. To set up the Controller, see pages C Cable Box/B 1 Cable signal Connections 2 F coaxial cable ANT. F 3 75Ω F coaxial cable T s ANTNNA jack 1Connect a Cable signal to the jack on the Cable Box/B. 2Use an F coaxial cable (supplied) to connect the jack on the Cable Box/B to the ANT(enna) jack on the C. 3Use a second F coaxial cable to connect the F jack on the C to the T s ANTNNA jack. ecording/iewing Any Channel 1With the C on and in C position (the C light will appear on the display panel), use the CH(annel) 8/9 button to set the C to the Cable Box/B output channel (channel 03 or 04). 2et the T to the same channel to which you set the C. et the CH3/CH4 switch on the C to the same channel. 3elect the channel you want to view/record at the Cable Box/B. Helpful Hint f you are using ecord ink, use audio and video cables to connect the / jacks on the Cable Box/B to the / jacks on the back of the C. etails are on page 35.

5 Hookups with a Cable Box/irect Broadcast ystem (cont d) 9 With this connection: You may watch one channel while recording another. You may not record scrambled channels. C Cable Box/B 1 Cable signal Connections 2 ANT. F F coaxial cable 3 F coaxial cable 75Ω T s ANTNNA jack 1Connect a Cable signal to the C s ANT(enna) jack. 2Use an F coaxial cable (supplied) to connect the F jack on the C to the jack on the Cable Box/B. 3Use a second F coaxial cable to connect the jack on the Cable Box/B to the T s ANTNNA jack. ecording ne Channel/Watching Another 1Put the Cable Box/B on the same channel as the C s CH3/CH4 switch. et the T to the Cable Box/B output channel (03 or 04). Then, with the C in C position (the C light will appear on the display panel), use the CH(annel) 8/9 button to select the channel you want to record at the C. tart the recording. 2Press the C/T button once to put the C in T position. (The C light will disappear.) 3elect the channel you want to watch at the Cable Box/B. Helpful Hint When you play a tape, make sure the Cable Box/B is set to the same channel as the CH3/CH4 switch on the C. et the T to the Cable Box/B output channel (03 or 04).

6 dB NM P P 22 Front Panel PW Button Press to turn the C power on and off. emote ensor eceives a signal from your remote control so you can operate your C from a distance. Press the C button on the remote control before pressing other C operation buttons. T/PAU Button uring tape playback, press once to freeze the picture. Press repeatedly to advance the till picture frame by frame. uring tape playback, press and hold for three seconds to start low Motion playback. etails are on page 61. uring recording, press to temporarily stop the recording. etails are on page 30. Fast Forward - Button When tape playback is stopped, press to fast forward the tape at high speed. uring tape playback, press to fast forward the tape while the picture stays on the screen. etails are on page 61. Press to change the setting of a C menu item. ewind / Button When tape playback is stopped, press to rewind the tape at high speed. uring tape playback, press to rewind the tape while the picture stays on the screen. etails are on page 61. Press to return to a previous C menu. PAY Button Press to play a tape. Press to release low, till or earch mode and return to normal playback. etails are on page B 4-HA H-F T CATT C PW UP H T TUB TM. MATPCTU. MUTBAN T CNT C / T PAY T / PAU -H T C MNU K/ TATU CHANN TP/JCT / TUB Front / n Jacks Connect cables coming from the and Jacks of another C or a camcorder here. etails are on page 48. To access these jacks, gently flip down the plastic cover. -H T Button Press to select -H T N or FF. -H T allows recording with -H picture quality on H cassettes. etails are on page 32. MNU Button Press to access or remove the C menu. K/TATU Button Press to go to the next C menu. Press to see the status display. etails are on page 26. Press repeatedly to see the real-time counter, remaining tape time, the current channel, or the current time on the display panel. etails are on page 21. TP/JCT Button Press once to stop the tape. When tape playback is stopped, press to eject the tape. C(ord)/T Button Press once to record. etails are on page 30. Press repeatedly to start a ne- Touch ecording. etails are on page 34. CHANN 8/9 Buttons Press to scan through the C s channels. uring tape playback, press to manually adjust the tracking. etails are on page 64. Press to select an item in the C menu.

7 ear Panel 23 ANT(enna) Jack Connect your antenna or cable here. etails are on pages 6-9. Jacks Connect audio cables going to the jacks of a camcorder, another C, or an audio system here. etails are on pages 48 and 55. Jacks Connect audio cables coming from the jacks of a camcorder, another C, a Cable Box/B, or an audio source here. etails are on pages 35 and 48. Jack Connect the Controller here. You may use the Controller with either a Cable Box or B receiver. etails are on pages ANT. F - Jack Connect an -ideo cable coming from the - jack of a camcorder or another C here. - Jack Connect an -ideo cable going to the - n jack of a T here. You may use -ideo connections instead of the standard CA-style video (yellow) connections. -ideo connections provide a better picture. CH3/CH4 witch et to channel 3 or 4 to use your T with your C. et your T to the same channel. etails are on pages 7-9. Jack Connect a video cable coming from the jack of a camcorder, a Cable Box/B, or another C here. etails are on pages 35 and 48. AC Power Cord Connect to a wall outlet (120 ) to supply power to the C. F Jack Use the supplied F coaxial cable to connect this jack to the ANTNNA Jack on your T or to the Jack on your Cable Box/B (if applicable). etails are on pages 7-9. Jack Connect a video cable going to the jack of a camcorder or another C here. etails are on pages 48 and 55.

8 48 erecording (Tape uplication) The instructions on this page show you how to copy tapes. ifferent Cs may operate differently. To duplicate a tape, make the connections shown, then follow steps 1-6. (You may use the and n jacks on the front of C 2 instead if you prefer.) C 1 Playing C C 2 ecording C 3) Use an F coaxial cable to connect the F Jack on C 2 to the T s ANTNNA Jack. ANT. F ANT. F 1) Use audio cables to connect the Jacks on C 1 to the Jacks on C 2. audio cables video cable 2) Use a video cable to connect the Jack on C 1 to the Jack on C 2. (r, to improve picture quality, you may connect an -ideo cable to the - jack on C 1 and to the - jack on C 2 instead.) 1C 1 will play your tape. nsert a prerecorded tape in C 1. f the tape does not have a record tab, playback begins. f this happens, press the TP/JCT button on C 1 once. 2C 2 will record your tape. nsert a blank tape in C 2. Make sure the C power is on and the C is in C position. (The C light will appear on the display panel. f it does not, press the C/T button once.) 3Turn on the T; set it to channel 3 or 4, whichever channel the CH3/CH4 switch on C 2 is set to. 4Point the remote control at C 2. Press the C button, then press the Number buttons 0, 0. Press the CH(annel) 8/9 button so that A/ FNT or A/ A appears on the screen. 5Point the remote control at C 2. Press the AT/P button to select P or P. 6Press the PAY button on C 1 and the C(ord)/T button on C 2 at the same time. The \ light will appear on the C 2 display panel. Helpful Hints Unauthorized recording of copyrighted television programs, video tapes, or other materials may infringe on the rights of copyright owners and violate copyright laws. f a program has copyright protection, it may not record clearly. Audio and video cables are not included. To stop copying tapes, press the TP/JCT button on C 2, then press the TP/JCT button on C 1. f you connect the audio and video cables to the / n jacks on the front of C 2, you must select A/ FNT at step 4. f you connect the audio and video or -ideo cables to the / or /- jacks on the back of C 2, you must select A/ A at step 4. Then select or - at A A/ PUT in the C et Up menu.

9 NM -15dB C P P TP/JCT / Connecting the Controller 49 f you are using a Cable Box/B, connect the Controller to your C. The Controller will automatically select channels at the Cable Box/B during a timer recording. eave your Cable Box/B turned on during a timer recording. 1Connect the Cable Box/B to the C as shown below. For more information, please read page 8. r, refer to the owner s manual of your Cable Box/B. Cable Box/B Controller Connect the Controller to the Jack on the back of the C. Connect the Cable signal to the Jack of the Cable Box/B. Use an F coaxial cable to connect the Jack on the Cable Box/B to the ANT(enna) Jack on the back of the C. CH3 CH4 ANT. F ANT. F Back of T (example) 75 Use a second F coaxial cable to connect the F Jack on the C to the T's ANTNNA Jack. 2Connect the Controller to the Jack on the back of the C as shown above. 3Attach the Controller to the top of the C using the supplied adhesive. Make sure the Controller s transmitter (the light on the top of the Controller) is pointed toward the Cable Box/B remote sensor. Cable Box/B Controller 960B 4-HA H-F T CATT C PW UP H T TUB TM. MATPCTU. MUTBAN T CNT C / T PAY T / PAU -H T MNU CHANN K/ TATU TUB 4f you are using a Cable Box, follow the steps on pages to make the Controller change channels at the Cable Box during timer recordings. f you are using a B, follow the steps on pages to make the Controller change channels at the B during timer recordings.

10 ANT. F Multi-Channel Television ound ystem (cont d) 55 To receive and record programs broadcast in second audio, follow steps 1-6. To receive and record a program broadcast in stereo, make one of the connections shown, then follow steps 1-6. ANT. f you have a tereo and a Monitor T, use a video cable to connect the C s Jack to the T s Jack. Use audio cables to connect the C s Jacks to the tereo s Jacks. F, if you have a single-speaker T, use an F coaxial cable to connect the C s F Jack to the T s ANTNNA Jack. 1Press the C button, then press the MNU button. C T UP TUN T UP TA T UP CT:,9 N: MNU CNFM: K 2Press the PAY 8 or TP 9 button to select C T UP, then press the K/TATU button. PC N N CN M N BU BACKGUN N TM C P MANUA TABZ FF HF NXT PAG CT:,9 CHANG: - N: MNU 3Press the PAY 8 or TP 9 button to select NXT PAG, then press the PAY 8 or TP 9 button to select T/AP on the second page of the C T UP menu. PU PAG T/AP AUT B C K -H M A A/ PUT AP N N CT:,9 CHANG: 3 N: MNU 4Press the FF - button to select AP (for a econd Audio Program) or T, whichever you prefer. 5Press the MNU button. 6ecord the program as usual. etails are on page 30. Helpful Hints f you want to connect the C to a tereo T, follow these steps. 1) Connect the antenna or cable signal to the C s ANT(enna) jack. 2) Use stereo audio cables to connect the C s jacks to the T s jacks. 3) Use a video cable to connect the C s jack to the T s jack. (r, to improve picture quality, you may connect an -ideo cable to the - jack on the C and to the - jack on the T instead.) Make sure the T and the tereo (if applicable) are in ine nput or Auxiliary mode. Please refer to your T or tereo owner s manual for details.