Integration of the Zetasizer µv and OmniFACE into an SEC system

Size: px
Start display at page:

Download "Integration of the Zetasizer µv and OmniFACE into an SEC system"

Transcription

1 Integration of the Zetasizer µv and OmniFACE into an SEC system PARTICLE SIZE MOLECULAR WEIGHT Introduction The Zetasizer µv is a light scattering system capable of simultaneous dynamic (DLS) and static light scattering (SLS) measurements of size and molecular weight. It can be used as a stand-alone batch instrument and can also be integrated into a sizeexclusion chromatography (SEC) system. This allows the system to perform DLS and SLS measurements under chromatographic conditions for measurements of size and molecular weight independent of sample elution volume. The OmniFACE analogue/ digital interface allows the connection of electrical signals from up to two concentration detectors and a trigger signal from an autosampler. The data is all collected and analyzed in OmniSEC, the dedicated SEC software package. Figure 1: The Zetasizer µv and OmniFACE This technical note describes how to integrate the Zetasizer µv and OmniFACE into a third-party SEC system. The fluidic connections are described, as are general electrical connections along with a few specific examples. Finally, instructions on how to connect OmniFACE and the Zetasizer µv to the PC and how to begin data collection are provided. Malvern Instruments Worldwide Sales and service centres in over 65 countries Malvern Instruments Limited

2 Fluidic connections The flow cell may include opaque connectors and tubing that are not appropriate for chromatography. A second set of black PEEK connectors and 1/16 chromatography tubing should be provided with the cell and these should be used (figure 2). In a standard chromatography setup, the eluent will flow from a reservoir through a pump, an autosampler, a column, and finally one or two detectors before flowing to waste. The eluent generally travels through 1/16 tubing after the pump. The black headless PEEK nut should be pushed onto the 1/16 inch tubing. Then the blue or white flat bottom compression fitting provided should be pushed onto the tubing so it is flush with the end of the tube (figure 2). Figure 2: PEEK nut and ferrule connector on 1/16 inch tubing. The Zetasizer µv can be placed at any point in the detector series after the column. This should be done in accordance with the requirements of other detectors which have back-pressure limits that should be carefully followed. The outlet from the column or another detector on the SEC system should be connected to the inlet on the flow cell and then from the outlet of the flow cell to the next detector or to waste (figure 3). The inlet is indicated by an arrow (figure 3A). The cell should be inserted and the lid closed without putting too much tension on the tubing (figure 3B). Figure 3: A. Flow tubing connected to flow cell. B. Cell inserted into Zetasizer µv with tubing coming through side gap. Adding the Zetasizer µv to a third party chromatography setup should have no effect on the system. The flow cell can be removed from the Zetasizer µv, leaving it free 2 Integration of the Zetasizer µv and OmniFACE into an SEC system

3 for batch use, without having to be disconnected from the fluid connections to other detectors unless desired. Figure 4: The backplate and electrical connections on the OmniFACE. Electrical connections external detectors Analogue cables from SEC systems are often provided by the manufacturer. If unavailable, the appropriate connections can usually be identified and created from the user manuals. On the back of each external detector should be connectors to output an analogue signal (e.g. 0-1V). The manual should help identify the signal out and ground connections from the external detectors. The signal out or + connection should be connected to the UV in HI or RI in HI on the OmniFACE depending on the detector used. The ground or should be connected to UV in LO or RI in LO on the OmniFACE. To test the connection, a run can be started in the OmniSEC software and the signal from the detectors monitored. Electronic connections start signal Many chromatography systems include an autosampler to enable multiple injections to be performed without the need for an operator to be present e.g. overnight. In order to synchronize the actions of the equipment used in this process, most chromatography equipment sends an electrical signal between injectors/pumps/detectors. The OmniFACE can recognize this signal in order to automatically start data collection. The OmniFACE requires that this signal is a contact closure The connector that sends the start signal can be identified by looking at the back of the autoinjector and pump and in the manual. This will be labeled inject start or start signal or trigger signal or similar. The + or signal socket is connected to TRIG SW; on the OmniFACE and the or ground to TRIG GND on the OmniFACE. To test this, a run with an autosampler should be started and then when OmniSEC is waiting for the trigger, an injection can be performed and the measurement should start. GE Healthcare (Amersham) AKTA system The AKTA chromatography system is in common usage throughout the life sciences market. The connections on this system are not standard but can still be connected to the Zetasizer µv. 3 Integration of the Zetasizer µv and OmniFACE into an SEC system

4 UV analogue signal The analogue signal comes from a 6-pin mini DIN socket located at the back of the instrument (figure 5) labeled Analogue out 0-1V. This contains analogue outputs and grounds for UV, conductivity and ph depending on the configuration of the instrument. A cable may have been provided with the AKTA system but may also need to be created. This will have an appropriate 6-pin mini DIN plug at one end and loose wires at the other. The black wire (1) corresponds to the UV signal out and the brown wire (2) corresponds to the appropriate ground. Connecting these two to the UV in HI and UV in LO sockets on OmniFACE should provide the analogue UV signal. Figure 5: 6-pin mini DIN socket on the monitor UPC-900 and cable required for connecting the analogue signals. When the signal becomes negative, the analogue output from the AKTA is reset to 1 V to show the decrease. To avoid this, an offset can be set into the instrument such that the output signal is 2% (0.02 V) above 0V. This is done on the Monitor UPC-900. Using the wheel select - Set Parameters: UV: Set UV Analogue Out: Set UV zero level. It is useful to include this step to avoid the analogue signal jumping to 1V at random intervals throughout the run. Start signal The start signal can be set to come from the remote socket on the back of the AKTA instrument (figure 6). This is an RS-232 type socket. Pins 6-9 correspond to AuxOut signals and pin 5 is a universal ground signal. 4 Integration of the Zetasizer µv and OmniFACE into an SEC system

5 Figure 6: 9-pin RS-232 socket for outputting a start signal on the GE AKTA FPLC pump and details for connecting the signals. A new cable should be made by connecting wires to pins 5 and 6 on a new RS-232 plug, or an existing cable can be cut and the wires connecting to pins 5 and 6 identified. The cable is plugged into the socket on the back of the AKTA instrument. The wire connected to pin 5 is connected to TRIG SW on the OmniFACE and the wire connected to pin 6 to TRIG GND on the OmniFACE. The Unicorn software controlling the customer s AKTA system is required to control the signal. Click on manual pump in the menu of the system control application. The menu should include a number of options including AuxOut 1 to 4. If the wire has been correctly connected, then AuxOut1 should act as the start signal. If the aux signals are not present, they need to be activated in the system settings. Go to the Unicorn manager application. Click on admin - system setup. Click on the diagram representing the chromatography system and click edit then on components. Check the box next to Auxiliary equipment and click Ok. The AuxOut signals should now be available in the manual pump options and in the method editor. Waters Alliance 2695 SEC autosampler and 2487 Dual Wavelength Detector The following connections are made between the Zetasizer µv, the Waters Alliance separation unit and the Waters 2487 Dual Wavelength Absorbance Detector (figure 7). 5 Integration of the Zetasizer µv and OmniFACE into an SEC system

6 Figure 7: External connectors on the Waters Alliance system. UV analogue signal The detector measures at two wavelengths (A & B). One of these can be connected as the UV detector on the OmniFACE. The analogue outputs on this device are screw fittings. UV in HI on the OmniFACE is connected to socket B1 and UV in LO on the OmniFACE to socket B3 for the wavelength A. Start signal The start signal from the separations module can be connected to the Zetasizer µv. The 2695 module has 2 connections for an inject start output labelled B1 and B2. These should be connected to TRIG SW and TRIG GND, respectively. Agilent 1100 and 1200 and HP 1050, 1100 series system These HPLC systems are the white stackable systems. The individual units communicate with each other using CAN connectors that look like Ethernet connectors. HP/Agilent s Variable Wavelength Detector (VWD) and RI At the back of the detector a BNC connector is used to output an analogue signal. The outside is the ground. This should be connected to UV in LO on the OmniFACE and the core of the BNC connector to UV in HI on the OmniFACE as desired. Using the software, the BNC analogue output can be configured to send either the VWD or the dri signal for the RI detector. HP/Agilent s pump The pump has a DB-9 connector at the back labeled REMOTE. Pin 1 connects to TRIG GND on the OmniFACE, while pin 3 from the APG remote goes to the TRIG SW on the OmniFACE. Figure 8 shows the two relevant sockets. 6 Integration of the Zetasizer µv and OmniFACE into an SEC system

7 Figure 8: Sockets on the rear of the HP/Agilent SEC system Data Collection The Zetasizer µv connects directly to the PC via USB while the OmniFACE connects via a RS-232. The drivers for the Zetasizer µv will be installed with either the Zetasizer or the OmniSEC software. In OmniSEC, the OmniFACE should be connected first. This is done in the Acquire-Search for Devices menu, found under the? menu. TDA 302 Family should be selected and the search started. The software should identify the com port to which the OmniFACE is attached. Click OK (figure 9A). 7 Integration of the Zetasizer µv and OmniFACE into an SEC system

8 Figure 9: A. Connecting the OmniFACE. B. Connecting the Zetasizer. C. Starting a measurement. Connection of the Zetasizer µv is performed in the Acquire-Configure menu; found under the? menu. Configure is selected next to the in-line DLS. The use DLS box must be checked in order to run the Zetasizer µv. The other options in this box allow the DLS settings and thresholds to be set. Click OK (figure 9B). To start a run, the quick-run button with the play symbol is clicked. The details of the run are filled in and the quick-run button clicked. The software will initialize the Zetasizer and the measurement will be started. If an autosampler is connected, the system will wait for the trigger signal before starting (figure 9C). ÄKTA is a trademark of GE. Healthcare Bio-Sciences AB. Waters Alliance is a registered trademark of Waters Corporation. Agilent, HP and 1050, 1100, 1200 are trademarks of Agilent Technologies Corp. Malvern Zetasizer Nano is a trademark of Malvern Instruments. All other trademarks are acknowledged. 8 Integration of the Zetasizer µv and OmniFACE into an SEC system

9 Malvern Instruments Limited Grovewood Road, Malvern, Worcestershire, UK. WR14 1XZ Tel: Fax: Malvern Instruments is part of Spectris plc, the Precision Instrumentation and Controls Company. Spectris and the Spectris logo are Trade Marks of Spectris plc. All information supplied within is correct at time of publication. Malvern Instruments pursues a policy of continual improvement due to technical development. We therefore reserve the right to deviate from information, descriptions, and specifications in this publication without notice. Malvern Instruments shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance or use of this material. Malvern Instruments owns the following registered trademarks: Bohlin, FIPA, Insitec, ISYS, Kinexus, Malvern, Malvern 'Hills' logo, Mastersizer, Morphologi, Rosand, 'SEC-MALS', Viscosizer, Viscotek, Viscogel and Zetasizer Malvern Instruments Limited

Vasudevan Agilent 1100 Series HPLC w/ DAD & FLD Detector (nonbuffer

Vasudevan Agilent 1100 Series HPLC w/ DAD & FLD Detector (nonbuffer Vasudevan Agilent 1100 Series HPLC w/ DAD & FLD Detector (nonbuffer solvents) Updated November 14, 2017 Instrument instructions can be found at: http://academic.bowdoin.edu/chemistry/resources/instructions.shtml

More information

Real-time ph and Conductivity Data Acquisition with the ACQUITY UPLC H-Class Bio System, Auto Blend Plus, and the GE Healthcare Monitor ph/c-900

Real-time ph and Conductivity Data Acquisition with the ACQUITY UPLC H-Class Bio System, Auto Blend Plus, and the GE Healthcare Monitor ph/c-900 Real-time ph and Conductivity Data Acquisition with the ACQUITY UPLC H-Class Bio System, Auto Blend Plus, and the GE Healthcare Monitor ph/c-900 INTRODUCTION The ACQUITY UPLC H-Class Bio System with Auto

More information

P-2 Installing the monitor (continued) Carry out as necessary

P-2 Installing the monitor (continued) Carry out as necessary P-2 Installing the monitor (continued) Carry out as necessary Using the monitor without the bezel MDT552S satisfies the UL requirements as long as it is used with the bezel attached. When using the monitor

More information

Mortara X-Scribe Tango+ Interface Notes

Mortara X-Scribe Tango+ Interface Notes Mortara X-Scribe Tango+ Interface Notes To setup Tango+ with the X-Scribe stress system, simply follow the directions below. 1. Verify Correct RS-232 and ECG Trigger Cables RS-232 Cable used to communicate

More information

ICS-3000 System Installation Qualification

ICS-3000 System Installation Qualification IC System IQ ICS-3000 System Installation Qualification 2006 Dionex Corporation Document No. 065080 Revision 02 September 2006 Doc. 065080-02 2006, Dionex Corporation All rights reserved worldwide. Printed

More information

DM1624, DM1612, DM812

DM1624, DM1612, DM812 Installation Guide Hardware and Software DM Series Digital Processors models DM1624, DM1612, DM812 LECTROSONICS, INC. 1 Installation Specific Information Only This guide covers only installation related

More information

IRIG-B PTP Clock Converter Output Module Hardware Installation Manual

IRIG-B PTP Clock Converter Output Module Hardware Installation Manual IRIG-B PTP Clock Converter Output Module Hardware Installation Manual Kyland Technology Co., LTD. Publication Date: May 2012 Version: V1.2 Customer Service Hotline: (+8610) 88796676 FAX: (+8610) 88796678

More information

BMW12N-H NTV-KIT791. Kit Contents. BMW12N-H Interface. Interface Power Harness

BMW12N-H NTV-KIT791. Kit Contents. BMW12N-H Interface. Interface Power Harness 3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com BMW12N-H NTV-KIT791 Screen Connector Overview The BMW12N-H kit interfaces 2 composite video

More information

GE CardioSoft (Version 6.01 or higher) Tango M2 Interface Notes

GE CardioSoft (Version 6.01 or higher) Tango M2 Interface Notes GE CardioSoft (Version 6.01 or higher) Tango M2 Interface Notes To setup Tango M2 with your CardioSoft (V6.01 or higher), simply follow the directions below. 1. Verify Correct RS-232 and ECG Trigger Cables

More information

DX-10 tm Digital Interface User s Guide

DX-10 tm Digital Interface User s Guide DX-10 tm Digital Interface User s Guide GPIO Communications Revision B Copyright Component Engineering, All Rights Reserved Table of Contents Foreword... 2 Introduction... 3 What s in the Box... 3 What

More information

BMW12N-DYNAMIC KIT NTV-KIT717

BMW12N-DYNAMIC KIT NTV-KIT717 3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com BMW12N-DYNAMIC KIT NTV-KIT717 Screen Connector Overview The BMW12-N kit interfaces 2 video inputs

More information

EVD-L04/100A1-960, EVD-L08/200A1-960 and. EVD-L16/400A1-960 DVRs. Quick Operation Guide

EVD-L04/100A1-960, EVD-L08/200A1-960 and. EVD-L16/400A1-960 DVRs. Quick Operation Guide EVD-L04/100A1-960, EVD-L08/200A1-960 and EVD-L16/400A1-960 DVRs Quick Operation Guide Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer.

More information

EdgeConnect Module Quick Start Guide ITERIS INNOVATION FOR BETTER MOBILITY

EdgeConnect Module Quick Start Guide ITERIS INNOVATION FOR BETTER MOBILITY EdgeConnect Module Quick Start Guide ITERIS INNOVATION FOR BETTER MOBILITY 493456301 Rev B April 2009 Table of Contents Installation... 1 Setup... 2 Operation... 4 Live Video... 4 Video Settings... 5 Network

More information

Installation Note. Agilent 89441A Option AYC Installation Kit

Installation Note. Agilent 89441A Option AYC Installation Kit Installation Note Agilent 89441A Option AYC Installation Kit Part Number: 89441-90074 Printed in USA February 2002 Notice. The information contained in this document is subject to change without notice.

More information

Auxiliary states devices

Auxiliary states devices 22 Auxiliary states devices When sampling using multiple frame states, Signal can control external devices such as stimulators in addition to switching the 1401 outputs. This is achieved by using auxiliary

More information

ipump 622 Streaming Media Decoder Installation Quick Start Guide

ipump 622 Streaming Media Decoder Installation Quick Start Guide ipump 622 Streaming Media Decoder Installation Quick Start Guide General Information Unpacking and Inspection The Wegener ipump 622 Enterprise Media Server is an integrated satellite receiver and video

More information

Features of the 745T-20C: Applications of the 745T-20C: Model 745T-20C 20 Channel Digital Delay Generator

Features of the 745T-20C: Applications of the 745T-20C: Model 745T-20C 20 Channel Digital Delay Generator 20 Channel Digital Delay Generator Features of the 745T-20C: 20 Independent delay channels - 100 ps resolution - 25 ps rms jitter - 10 second range Output pulse up to 6 V/50 Ω Independent trigger for every

More information

Video Server SED-2100R/S. Quick Installation Guide

Video Server SED-2100R/S. Quick Installation Guide Video Server SED-2100R/S Quick Installation Guide Feb.10,2006 1 1 Getting Started 1.1 PACKAGE CONTENTS SED-2100 Warranty Card Software CD Hook up & Screws Terminal Blocks for Power & DI/O Power Adaptor

More information

Welch Allyn CardioPerfect Workstation Tango+ Interface Notes

Welch Allyn CardioPerfect Workstation Tango+ Interface Notes Welch Allyn CardioPerfect Workstation Tango+ Interface Notes To setup Tango+ with the CardioPerfect stress system, simply follow the directions below. 1. Verify Correct RS-232 and ECG Trigger Cables RS-232

More information

Quick Operation Guide of LTN7700/7600 Series NVR

Quick Operation Guide of LTN7700/7600 Series NVR Quick Operation Guide of LTN7700/7600 Series NVR UD.6L0202B0042A02 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual is applicable

More information

Control Unit CU 2.1 User Manual V6850A HPLC

Control Unit CU 2.1 User Manual V6850A HPLC Control Unit CU 2.1 User Manual V6850A HPLC 3 Table of Contents Control Unit... 5 Control... 5 Start Screen... 6 Main Menu... 6 Programs and Links... 7 General Settings... 8 Choosing the Network... 8 Setting

More information

DINOX&Digital&Video&Recorder&

DINOX&Digital&Video&Recorder& DINOX&Digital&Video&Recorder& & & & & & & & & & &&&Quick&Operation&Guide& UD.7L0X02B1228B01& Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact

More information

Digital Video Recorder

Digital Video Recorder Digital Video Recorder Quick Operation Guide UD.6L0202B0067A02 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual is applicable

More information

TL-2900 AMMONIA & NITRATE ANALYZER DUAL CHANNEL

TL-2900 AMMONIA & NITRATE ANALYZER DUAL CHANNEL TL-2900 AMMONIA & NITRATE ANALYZER DUAL CHANNEL DATA ACQUISITION SYSTEM V.15.4 INSTRUCTION MANUAL Timberline Instruments, LLC 1880 S. Flatiron Ct., Unit I Boulder, Colorado 80301 Ph: (303) 440-8779 Fx:

More information

GWL/ Power Group Technology Solutions Stay Powered for the Future

GWL/ Power Group Technology Solutions Stay Powered for the Future GWL/ Power Group Technology Solutions Stay Powered for the Future BMS2405 CONNECTION GUIDE: This is simple step-by-step manual how to CONNECT AND proceed basic SETUP of BMS2405. In following example connection

More information

GFT Channel Digital Delay Generator

GFT Channel Digital Delay Generator Features 20 independent delay Channels 100 ps resolution 25 ps rms jitter 10 second range Output pulse up to 6 V/50 Ω Independent trigger for every channel Fours Triggers Three are repetitive from three

More information

DS-7200HVI/HFI-SH Series DVR Quick Operation Guide

DS-7200HVI/HFI-SH Series DVR Quick Operation Guide DS-7200HVI/HFI-SH Series DVR Quick Operation Guide UD.6L0202B0019A01 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual is

More information

Artistic Licence Engineering Ltd Firmware Version V3.03 Manual Revision V1-9

Artistic Licence Engineering Ltd Firmware Version V3.03 Manual Revision V1-9 Light-Switch & Switch-Edit Artistic Licence Engineering Ltd Firmware Version V3.03 Manual Revision V1-9 Artistic Licence Engineering Ltd. Switch-Edit Manual 2/47 Artistic Licence Engineering Ltd. Switch-Edit

More information

Instrument Control and Data Acquisition with Chromeleon

Instrument Control and Data Acquisition with Chromeleon Technical Note 67 Instrument Control and Data Acquisition with Chromeleon Introduction Laboratories generally have a combination of chromatography devices from different manufacturers and, therefore, face

More information

Quinton Q-Stress Version 6.x.x Tango M2 Interface Notes

Quinton Q-Stress Version 6.x.x Tango M2 Interface Notes Quinton Q-Stress Version 6.x.x Tango M2 Interface Notes To setup Tango M2 with the Q-Stress cardiac stress system, simply follow the directions below. 1. Verify Correct RS-232 and ECG Trigger Cables RS-232

More information

EEG A1452 SCTE-104 Inserter Frame Card

EEG A1452 SCTE-104 Inserter Frame Card EEG A1452 SCTE-104 Inserter Frame Card Product Manual EEG Enterprises, Inc. 586 Main Street Farmingdale, New York 11735 TEL: (516) 293-7472 FAX: (516) 293-7417 Copyright EEG Enterprises, Inc. 2017 All

More information

FTC AGL System Controller Reference Manual Part Number

FTC AGL System Controller Reference Manual Part Number SERIAL NUMBER FTC 190-1 AGL System Controller Reference Manual Part Number 7911901 Flash Technology, 332 Nichol Mill Lane, Franklin, TN 37067 (615) 261-2000 Front Matter Abstract This manual contains information

More information

National Instruments SCB-68 Breakout Box

National Instruments SCB-68 Breakout Box National Instruments SCB-68 Breakout Box Description The SCB-68 is a shielded I/O connector block that has been modified by Plexon to facilitate interfacing Plexon hardware with the National Instruments

More information

Quick Guide Book of Sending and receiving card

Quick Guide Book of Sending and receiving card Quick Guide Book of Sending and receiving card ----take K10 card for example 1 Hardware connection diagram Here take one module (32x16 pixels), 1 piece of K10 card, HUB75 for example, please refer to the

More information

Cardioline Cube Stress Tango M2 Interface Notes

Cardioline Cube Stress Tango M2 Interface Notes Cardioline Cube Stress Tango M2 Interface Notes To setup Tango M2 with the Cube stress system, simply follow the directions below. 1. Verify Correct RS-232 and ECG Trigger Cables RS-232 Cable used to communicate

More information

Camera Setup Instructions

Camera Setup Instructions Camera Setup Instructions Hopefully this document will help new MallinCam owners set up their systems and get them to successful first light more quickly. Through the use of images, I hope to describe

More information

User Manual V2.6. Omniksol WIFIKIT User Manual. Omnik New Energy Co., Ltd.

User Manual V2.6. Omniksol WIFIKIT User Manual. Omnik New Energy Co., Ltd. User Manual V2.6 Omniksol WIFIKIT User Manual Omnik New Energy Co., Ltd. Overview of WIFIKIT Function Omniksol-WIFIKIT is developed by Omnik as an external communication monitoring device, which integrates

More information

Pulse Biomedical QRS-Card Tango M2 Interface Notes

Pulse Biomedical QRS-Card Tango M2 Interface Notes Pulse Biomedical QRS-Card Tango M2 Interface Notes To setup Tango M2 with your stress system, simply follow the directions below. 1. Verify Correct RS-232 and ECG Trigger Cables RS-232 Cable used to communicate

More information

HP Media Center Extender Quick Start Guide Start Here

HP Media Center Extender Quick Start Guide Start Here HP Media Center Extender Quick Start Guide Start Here 2004, Hewlett-Packard Development Company, L.P. Printed in Welcome to the Media Center Extender Setup Required! You must upgrade to Microsoft Windows

More information

MENU EXECUTE Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free

MENU EXECUTE Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free Instruction Manual Model 2584-31 Combiner May 2011, Rev. A RF MONITOR GAIN = -15 MENU MODEL 2584 COMBINER CROSS TECHNOLOGIES INC. ALARM REMOTE POWER EXECUTE Data, drawings, and other material contained

More information

SwiftMix Automation Safety

SwiftMix Automation Safety Operations Manual SwiftMix TM Automation Thank you for your purchase of the SwiftMix automation for the 5088 console. Everyone at Rupert Neve Designs hopes you enjoy using this tool as much as we have

More information

HawkEye 1500 Series Quick Start Guide V2.4.1, Nov 2008

HawkEye 1500 Series Quick Start Guide V2.4.1, Nov 2008 HawkEye 1500 Series Quick Start Guide V2.4.1, Nov 2008 EM-40390-1V241 Copyright and Disclaimer Copyright 2008 by Microscan Systems, Inc. 1201 S.W. 7th Street, Renton, WA, U.S.A. 98057 (425) 226-5700 FAX:

More information

AC335A. VGA-Video Ultimate Plus BLACK BOX Back Panel View. Remote Control. Side View MOUSE DC IN OVERLAY

AC335A. VGA-Video Ultimate Plus BLACK BOX Back Panel View. Remote Control. Side View MOUSE DC IN OVERLAY AC335A BLACK BOX 724-746-5500 VGA-Video Ultimate Plus Position OVERLAY MIX POWER FREEZE ZOOM NTSC/PAL SIZE GENLOCK POWER DC IN MOUSE MIC IN AUDIO OUT VGA IN/OUT (MAC) Remote Control Back Panel View RGB

More information

Mortara XScribe Versions 3.xx and 5.xx Tango M2 Interface Notes

Mortara XScribe Versions 3.xx and 5.xx Tango M2 Interface Notes Mortara XScribe Versions 3.xx and 5.xx Tango M2 Interface Notes To setup Tango M2 with the XScribe cardiac stress system, simply follow the directions below. 1. Verify Correct RS-232 and ECG Trigger Cables

More information

Quick Start. RSHS1000 Series Handheld Digital Oscilloscope

Quick Start. RSHS1000 Series Handheld Digital Oscilloscope Quick Start RSHS1000 Series Handheld Digital Oscilloscope General Safety Summary Carefully read the following safety precautions to avoid personal injury and prevent damage to the instrument or any products

More information

Philips StressVue Tango M2 Interface Notes

Philips StressVue Tango M2 Interface Notes Philips StressVue Tango M2 Interface Notes To setup Tango M2 with the StressVue stress system, simply follow the directions below. 1. Verify Correct RS-232 and ECG Trigger Cables RS-232 Cable used to communicate

More information

ASKING FOR ASSISTANCE

ASKING FOR ASSISTANCE ASKING FOR ASSISTANCE Technical Support: Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday through Friday PST. Write To: Gefen Inc. c/o Customer

More information

CytoFLEX Flow Cytometer Quick Start Guide

CytoFLEX Flow Cytometer Quick Start Guide Sheath Waste CLASS 1 LASER PRODUCT COMPLIES WITH 21 CFR 1040.10 AND 1040.11 EXCEPT FOR DEVIATIONS PURSUANT TO LASER NOTICE NO. 50 DATED JUNE 24, 2007 MANUFACTURED Sheath B49008AC February 2015 CytoFLEX

More information

DTV742 Installation Quick Start Guide

DTV742 Installation Quick Start Guide DTV742 Installation Quick Start Guide The Wegener Model DTV742 8VSB 4-Channel Multiplexor receives VHF/UHF broadcast HDTV signals and provides output ASI streams for connection to cable system QAM modulators.

More information

Extremely high sensitivity Live Video Imaging using the SamBa SE-34

Extremely high sensitivity Live Video Imaging using the SamBa SE-34 Extremely high sensitivity Live Video Imaging using the SamBa SE-34 A special thanks for the cooperation and support from Coreco Imaging in enabling this feature. Introduction This document provides guidance

More information

DVI to HD-SDI Conversion Box

DVI to HD-SDI Conversion Box DVI to HD-SDI Conversion Box USER MANUAL www.gefen.com ASKING FOR ASSISTANCE Technical Support: Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday

More information

AEROTRAK PORTABLE AIRBORNE PARTICLE COUNTER MODEL 9110 QUICK START GUIDE

AEROTRAK PORTABLE AIRBORNE PARTICLE COUNTER MODEL 9110 QUICK START GUIDE AEROTRAK PORTABLE AIRBORNE PARTICLE COUNTER MODEL 9110 QUICK START GUIDE Thank you for purchasing a TSI AeroTrak Model 9110 Portable Airborne Particle Counter (particle counter). This guide will help you

More information

ivw-fd122 Video Wall Controller MODEL: ivw-fd122 Video Wall Controller Supports 2 x 2 Video Wall Array User Manual Page i Rev. 1.

ivw-fd122 Video Wall Controller MODEL: ivw-fd122 Video Wall Controller Supports 2 x 2 Video Wall Array User Manual Page i Rev. 1. MODEL: ivw-fd122 Video Wall Controller Supports 2 x 2 Video Wall Array User Manual Rev. 1.01 Page i Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice

More information

TeamWork Installation Guide

TeamWork Installation Guide C G G 00-0V/ A MAX TX RX +V APARATUS US 0 TeamWork Installation Guide TeamWork TeamWork is a fully customizable collaboration system comprised of an switcher, Show Me cables, a control processor, and a

More information

3-DRX. AUTOMATIC THREE CHANNEL DIGITAL AES/EBU REPEATER and ANALOG AUDIO SWITCHER INSTALLATION AND OPERATING MANUAL

3-DRX. AUTOMATIC THREE CHANNEL DIGITAL AES/EBU REPEATER and ANALOG AUDIO SWITCHER INSTALLATION AND OPERATING MANUAL 3-DRX AUTOMATIC THREE CHANNEL DIGITAL AES/EBU REPEATER and ANALOG AUDIO SWITCHER INSTALLATION AND OPERATING MANUAL 3-DRX SECTION 1 INTRODUCTION The TITUS TECHNOLOGICAL LABORATORIES 3-DRX AUTOMATIC THREE

More information

Model 6010 Four Channel 20-Bit Audio ADC Data Pack

Model 6010 Four Channel 20-Bit Audio ADC Data Pack Model 6010 Four Channel 20-Bit Audio ADC Data Pack Revision 3.1 SW v1.0.0 This data pack provides detailed installation, configuration and operation information for the Model 6010 Four Channel 20-bit Audio

More information

DTV744 Installation Quick Start Guide

DTV744 Installation Quick Start Guide DTV744 Installation Quick Start Guide The Wegener Model DTV744 8VSB 4-Channel Demodulator receives VHF/UHF broadcast HDTV 8VSB signals and provides output ASI streams for connection to an advanced cable

More information

Installation / Set-up of Autoread Camera System to DS1000/DS1200 Inserters

Installation / Set-up of Autoread Camera System to DS1000/DS1200 Inserters Installation / Set-up of Autoread Camera System to DS1000/DS1200 Inserters Written By: Colin Langridge Issue: Draft Date: 03 rd July 2008 1 Date: 29 th July 2008 2 Date: 20 th August 2008 3 Date: 02 nd

More information

ivw-fd133 Video Wall Controller MODEL: ivw-fd133 Video Wall Controller Supports 3 x 3 and 2 x 2 Video Wall Array User Manual Page i Rev. 1.

ivw-fd133 Video Wall Controller MODEL: ivw-fd133 Video Wall Controller Supports 3 x 3 and 2 x 2 Video Wall Array User Manual Page i Rev. 1. MODEL: ivw-fd133 Video Wall Controller Supports 3 x 3 and 2 x 2 Video Wall Array User Manual Rev. 1.01 Page i Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior

More information

Model 5250 Five Channel Digital to Analog Video Converter Data Pack

Model 5250 Five Channel Digital to Analog Video Converter Data Pack Model 5250 Five Channel Digital to Analog Video Converter Data Pack E NSEMBLE D E S I G N S Revision 3.1 SW v2.0.1 This data pack provides detailed installation, configuration and operation information

More information

TeamWork Kits Installation Guide

TeamWork Kits Installation Guide TX 0 RX COM +5V APARATUS US TeamWork Kits Installation Guide TeamWork 400 and TeamWork 600 Kits The TeamWork 400 and TeamWork 600 kits consist of an HDMI switcher, system controller, Cable Cubby, and cables

More information

MONITOR POWER Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free

MONITOR POWER Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free Instruction Manual Model 2099-10xx 10MHz Frequency Source April 2014, Rev. H MENU INTERNAL LEVEL = +10dBm MONITOR POWER 1 2 MODEL 2099 FREQUENCY SOURCE CROSS TECHNOLOGIES INC. ALARM OVEN REMOTE EXECUTE

More information

Customer Responsibilities. Important Customer Information Infinity LC/1260 Infinity LC Site Preparation Checklist

Customer Responsibilities. Important Customer Information Infinity LC/1260 Infinity LC Site Preparation Checklist 1290 Site Preparation Infinity LC/1260 Checklist Infinity LC Thank you for purchasing an Agilent instrument. To get you started and to assure a successful and timely installation, please refer to this

More information

VIDEO ALARM VERIFICATION UNIT VIVER

VIDEO ALARM VERIFICATION UNIT VIVER VIDEO ALARM VERIFICATION UNIT VIVER viver_en 09/08 The VIVER module provides remote video alarm verification, based on image sequences transmitted from cameras installed in the protected facility. The

More information

Analog Output for the TSI DUSTTRAK Aerosol Monitor Model 8520

Analog Output for the TSI DUSTTRAK Aerosol Monitor Model 8520 Exposure Monitoring Analog Output for the TSI DUSTTRAK Aerosol Monitor Model 8520 Application Note ITI-073 Introduction Newer models of the DUSTTRAK Model 8520 are capable of providing an analog output

More information

Six-Channel TDM Multiplexers for 3G, HD, SDI, and ASI. Installation and Operations. Manual

Six-Channel TDM Multiplexers for 3G, HD, SDI, and ASI. Installation and Operations. Manual Manual DigiLink DLC156 Function modules Six-Channel TDM Multiplexers for 3G, HD, SDI, and ASI Installation and Operations Manual WWW.ARTEL.COM ii DLC156 Function Modules Installation and Operations Manual

More information

CI-218 / CI-303 / CI430

CI-218 / CI-303 / CI430 CI-218 / CI-303 / CI430 Network Camera User Manual English AREC Inc. All Rights Reserved 2017. l www.arec.com All information contained in this document is Proprietary Table of Contents 1. Overview 1.1

More information

PM-240-MTP Multifiber Optical Power Meter INSTRUCTION MANUAL

PM-240-MTP Multifiber Optical Power Meter INSTRUCTION MANUAL PM-240-MTP Multifiber Optical Power Meter INSTRUCTION MANUAL Revision:1.0 is registered trademark of OPTOKON, a.s. Other names and trademarks mentioned herein may be the trademarks of their respective

More information

Dell Wyse 5030 PCoIP Zero Client

Dell Wyse 5030 PCoIP Zero Client Dell Wyse 5030 PCoIP Zero Client User Guide Regulatory Model: PxN Regulatory Type: PxN001 Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your

More information

AC334A. VGA-Video Ultimate BLACK BOX Remote Control. Back Panel View. Side View MOUSE DC IN BLACK BOX ZOOM/FREEZE POWER

AC334A. VGA-Video Ultimate BLACK BOX Remote Control. Back Panel View. Side View MOUSE DC IN BLACK BOX ZOOM/FREEZE POWER AC334A BLACK BOX 724-746-5500 VGA-Video Ultimate BLACK BOX 724-746-5500 Zoom Position PAL ZOOM/FREEZE POWER FREEZE ZOOM NTSC/PAL SIZE RESET POWER Size Power Remote Control DC IN MOUSE MIC IN AUDIO OUT

More information

READ THIS FIRST. Morphologi G3. Quick Start Guide. MAN0412 Issue1.1

READ THIS FIRST. Morphologi G3. Quick Start Guide. MAN0412 Issue1.1 READ THIS FIRST Morphologi G3 Quick Start Guide MAN0412 Issue1.1 Malvern Instruments Ltd. 2008 Malvern Instruments makes every effort to ensure that this document is correct. However, due to Malvern Instruments

More information

User Manual SM-7070WR

User Manual SM-7070WR User Manual SM-7070WR PRODUCT FUNCTION AND APPLICATION INTRODUCTION 1. Product function 7 inch digital panel Screen Ratio: 16: 9 Resolution: 800*RGB*480 Front Key Function: 7pcs mechanical keys Remote

More information

Booya16 SDR Datasheet

Booya16 SDR Datasheet Booya16 SDR Radio Receiver Description The Booya16 SDR radio receiver samples RF signals at 16MHz with 14 bits and streams the sampled signal into PC memory continuously in real time. The Booya software

More information

Document Part Number: Copyright 2010, Corelis Inc.

Document Part Number: Copyright 2010, Corelis Inc. CORELIS Low Voltage Adapter Low Voltage Adapter Boundary-Scan Interface User s Manual Document Part Number: 70398 Copyright 2010, Corelis Inc. Corelis, Inc. 12607 Hiddencreek Way Cerritos, CA 90703-2146

More information

TransitHound Cellphone Detector User Manual Version 1.3

TransitHound Cellphone Detector User Manual Version 1.3 TransitHound Cellphone Detector User Manual Version 1.3 RF3 RF2 Table of Contents Introduction...3 PC Requirements...3 Unit Description...3 Electrical Interfaces...4 Interface Cable...5 USB to Serial Interface

More information

Configuration Vestas VMP3500

Configuration Vestas VMP3500 Configuration Vestas VMP3500 1. Table of contents 1. Table of contents... 2 2. Introduction... 3 3. Vestas turbines (RCS)... 4 3.1. VMP 3500 controller... 4 3.2. Communication with the CT3230 current loop

More information

B. The specified product shall be manufactured by a firm whose quality system is in compliance with the I.S./ISO 9001/EN 29001, QUALITY SYSTEM.

B. The specified product shall be manufactured by a firm whose quality system is in compliance with the I.S./ISO 9001/EN 29001, QUALITY SYSTEM. VideoJet 8000 8-Channel, MPEG-2 Encoder ARCHITECTURAL AND ENGINEERING SPECIFICATION Section 282313 Closed Circuit Video Surveillance Systems PART 2 PRODUCTS 2.01 MANUFACTURER A. Bosch Security Systems

More information

8753E, 8753ET, and 8753ES Network Analyzer Option 1D5 High Stability Frequency Reference Upgrade Kit. Applicable Upgrade Kit Model Number

8753E, 8753ET, and 8753ES Network Analyzer Option 1D5 High Stability Frequency Reference Upgrade Kit. Applicable Upgrade Kit Model Number Installation Note 8753E, 8753ET, and 8753ES Network Analyzer Option 1D5 High Stability Frequency Reference Upgrade Kit Network Analyzer Model Number 8753E 8753ET 8753ES Applicable Upgrade Kit Model Number

More information

Agilent Parallel Bit Error Ratio Tester. System Setup Examples

Agilent Parallel Bit Error Ratio Tester. System Setup Examples Agilent 81250 Parallel Bit Error Ratio Tester System Setup Examples S1 Important Notice This document contains propriety information that is protected by copyright. All rights are reserved. Neither the

More information

Modular Matrix Solution. Complete A/V Signal Control in One Expandable System.

Modular Matrix Solution. Complete A/V Signal Control in One Expandable System. Modular Matrix Solution Complete A/V Signal Control in One Expandable System www.aten.com Overview When video is displayed across multiple screens to maximize marketing, live broadcasting or real-time

More information

Displays Open Frame Monitor Model Number: AND-TFT-150Bxx

Displays Open Frame Monitor Model Number: AND-TFT-150Bxx Displays 15.0 Open Frame Monitor Model Number: AND-TFT-150Bxx The AND-TFT-150Bxx 15.0 Open Frame Monitor series are rugged, high performance Industrial LCD Monitors, designed for commercial and industrial

More information

DA CHANNEL AES AUDIO MIXER/ ROUTER MODULE

DA CHANNEL AES AUDIO MIXER/ ROUTER MODULE DA5320 8-CHANNEL AUDIO MIXER/ ROUTER MODULE Document No. 14811 January 2005 14811 January 2005 Front Matter Page ii 14811 January 2005 Front Matter SIGMA ELECTRONICS's products are certified to comply

More information

USER GUIDE FOR NETmc MARINE X-Ops

USER GUIDE FOR NETmc MARINE X-Ops USER GUIDE FOR NETmc MARINE X-Ops Rev.2.2 Firmware v.1.2.8 X-Ops, 1.2.9 Pipeline September 2013 NETmc Marine X-Ops Manual-Rev.2.2 September 2013 1 of 17 Contents 1. Introduction... 3 1.1 Multi-channel

More information

Operation/Reference Guide IRIS. Infrared/Serial Data Capture Unit. Control System Accessories

Operation/Reference Guide IRIS. Infrared/Serial Data Capture Unit. Control System Accessories Operation/Reference Guide IRIS Infrared/Serial Data Capture Unit Control System Accessories Last Revised: 1/17/2007 AMX Limited Warranty and Disclaimer All products returned to AMX require a Return Material

More information

RDS: The RDS, or Radio Data System, is supported in the g! interface where available.

RDS: The RDS, or Radio Data System, is supported in the g! interface where available. Manufacturer: Integra Integration Note Model Number(s): Integra 20.3/30.3/40.3/50.3/70.3/80.3 Core Module Version: 5.4 Comments: FW 1.09 (1091-0999-0210-9105) Document Revision Date: 1/15/2013 OVERVIEW

More information

Installation & Operational Manual

Installation & Operational Manual Radiant Communications Corporation 5001 Hadley Road South Plainfield NJ 07080 Tel (908) 757-7444 Fax (908) 757-8666 WWW.RCCFIBER.COM QRF5000M MDU ENCODER Installation & Operational Manual Rev.A2 1. Introduction

More information

MaxView Cinema Kit Quick Install Guide

MaxView Cinema Kit Quick Install Guide SYSTEM SETUP The MaxView will work at any of the following display settings: INSTALLATION MaxView Cinema Kit Quick Install Guide Step 1 - Turn off your computer. Disconnect your monitor s VGA cable from

More information

DXP A0808 Quick Start

DXP A0808 Quick Start VIEWSIZE THE WORLD DXP A0808 Quick Start Support any in any out Support independent output switching Support infrared remote control Input and output can be modularized RS 232 loop out for multiple control

More information

Scan Converter Quick Installation Guide

Scan Converter Quick Installation Guide Scan Converter Quick Installation Guide Software Note: No software is required to use your scan converter. Please complete the hardware installation and system setup before you determine the need to the

More information

AES-402 Automatic Digital Audio Switcher/DA/Digital to Analog Converter

AES-402 Automatic Digital Audio Switcher/DA/Digital to Analog Converter Broadcast Devices, Inc. AES-402 Automatic Digital Audio Switcher/DA/Digital to Analog Converter Technical Reference Manual Broadcast Devices, Inc. Tel. (914) 737-5032 Fax. (914) 736-6916 World Wide Web:

More information

Contents: 1 LANsmart Pro Main Unit 4 Remote Unit: ID1, ID2, ID3, ID4

Contents: 1 LANsmart Pro Main Unit 4 Remote Unit: ID1, ID2, ID3, ID4 LANsmart Pro user manual Introduction LANsmart Pro is a hand-held, multifunction Cable Map Tester and Cable Length Meter. It has an integrated Analog and Digital Tone Generator, Port Finder, and Quick

More information

Instruction Manual for Electronic Blowers and Flashboards

Instruction Manual for Electronic Blowers and Flashboards Instruction Manual for Electronic Blowers and Flashboards These instructions cover both the table model 17212 table top Electronic Bingo Blower (Fig 1) and the 17213 floor model Electronic Bingo Blower

More information

AES-404 Digital Audio Switcher/DA/Digital to Analog Converter

AES-404 Digital Audio Switcher/DA/Digital to Analog Converter Broadcast Devices, Inc. AES-404 Digital Audio Switcher/DA/Digital to Analog Converter Technical Reference Manual Broadcast Devices, Inc. Tel. (914) 737-5032 Fax. (914) 736-6916 World Wide Web: www.broadcast-devices.com

More information

LED Array Board.

LED Array Board. LED Array Board www.matrixtsl.com EB087 Contents About This Document 2 General Information 3 Board Layout 4 Testing This Product 5 Circuit Description 6 Circuit Diagram 7 About This Document This document

More information

RF Solution for LED Display Screen

RF Solution for LED Display Screen RF Solution for LED Display Screen Introduction RF is a kind of wireless telecommunication technology, now standard IEEE802.11B is much popular. Communication speed between server and terminal can reach

More information

USER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.1

USER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.1 by USER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.1 www.aeroforcetech.com Made in the USA! WARNING Vehicle operator should focus primary attention to the road while using the Interceptor. The information

More information

SCALE & WEIGHT DISPLAYS

SCALE & WEIGHT DISPLAYS The MICRO SERIES SCALE & WEIGHT DISPLAYS LARGE DIGIT MODELS Mighty-5S DPM MODELS Micro-S & Mighty-1S Mighty-1S Micro-S ELECTRO-NUMERICS, INC. Introduction The Electro-Numerics family of Digital Panel Meters

More information

OPERATIONAL MANUAL EMZS CH Speaker Zone Selector. Version 1.6

OPERATIONAL MANUAL EMZS CH Speaker Zone Selector. Version 1.6 OPERATIONAL MANUAL EMZS-8012 12CH Speaker Zone Selector Version 1.6 1 Product Overview The EMZS-8012 is a 1U rack-mounting unit, provide 12 channel direct zone switching for single source public address

More information

Operation Manual for the Refractive Index detector VE-3580

Operation Manual for the Refractive Index detector VE-3580 Operation Manual for the Refractive Index detector VE-3580 October 2012 (MAN0446-1.0) (Version 4.3) Page 1 of 32 pages Table of Contents Table of Contents... 3 Notices, Warnings and Definitions... 5 Figures...

More information

NX APPLICATION NOTE Led Guided Assembly Connector Pinning with Continuity

NX APPLICATION NOTE Led Guided Assembly Connector Pinning with Continuity NX APPLICATION NOTE Led Guided Assembly Connector Pinning with Continuity Background Many wire harness connectors are designed to use a push-click-pull method of wire insertion. This method requires the

More information