SYSTEM 4xi PROJECTOR COMMUNICATIONS KIT ATTENTION! PLEASE READ THIS DOCUMENT FOR IMPORTANT INSTALLATION INSTRUCTIONS

Transcription

1 SYSTEM 4xi PROJECTOR COMMUNICATIS KIT ATTENTI! PLEASE READ THIS DOCUMENT FOR IMPORTANT INSTALLATI INSTRUCTIS THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPENTS: Kit Type: BARCO Included Communicatis (s): Quantity Part Number Descripti 1 RCDS THE TABLE BELOW LISTS THE POSSIBLE CFIGURATI(S) AND CORRESPDING COMMUNICATIS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER S ARIOUS MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CFIGURED AS INDICATED BY THE 4 IN THE CFIG AS COLUMN. IF YOUR PROJECTOR MODEL DIFFERS FROM THIS CFIGURATI, YOU MUST RECFIGURE YOUR SWITCHER WITH THE CORRECT SETTINGS. PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CFIGURATI AND SIGNAL CNECTI INSTRUCTIS. THIS SWITCHER HAS BEEN CFIGURED FOR: BARCO CRT Cfig as Model RC5 PPM PROJ CABLE Comm 4 CRT LCD 0 A C Extr

2 Cnecting to CRT/LCD Projector [ model and software versi displayed here] (Note: Informati depends setup.) If the is already cfigured for a CRT/LCD projector, go to step 4. If it is not set up correctly, it will be necessary to change switch settings the s Main Ctroller Board. Begin at Step 1 to verify the correct cfigurati. This procedure is for the CRT projector as well as the 8100LC. 1. Use the Frt Panel to display the Informati Menu to verify that the is already set up for the projector. Apply power to the and do the following: a. Press to display the MENU SELECT the LCD screen. b. Press or to step to Menu 8. c. Press to select this menu. } d. Press or to display the cfigurati. The example to the left is general, your display will show the model name, the software versi and the following informati: PRJ = BARCO PRJ BAUD = 1200 UNIT No. = 000 HST BAUD = 9600 (value depends up setup Menu 3) 2. Go to the procedure page 2-3 of the User s Manual to remove the cover. Then go to page 2-4 and refer to the cfiguratis below to set up the Main Ctroller board. Ctinue with Step 3 (below) when the cfigurati is correct. Cfig Model PRJ Comm as RC5 PPM CABLE CRT LCD 0 A C CRT Cfigurati LCD (except model 5000) 5000 Cfigurati 6300 Cfigurati Extr Page 1

3 3. Double-check your work and be sure the cover is securely. 4. Install the in its place of operati (i.e. rack), but not powered. Changes in some switch cfiguratis are not detected until the power is removed at the AC cord, and then restored. Refer to the following cnecti diagrams and ctinue. Use the Comm provided by Extr (BR COM ). 5. The Comm has a cable with a 9-pin female cnector. Plug this into the male Comm Port cnector the rear of the projector. 6. Plug the HD 15-pin cnector of the Projector Communicatis Extensi cable (shown as CC 50'/100') into the PJ Comm port the. The other end has a 9-pin female cnector. Plug this into the male cnector the BR COM case. Secure all of the cnector screws. 7. Plug the (4 or 5) BNC cnectors from e end of the (user-supplied) RGBS/H cable to the output and those the other end to the BNC cnectors the rear of the projector (marked RGsB/RGBS/RGBH). Series CRT Projector Cnectis Use the following illustratis as a guide when cnecting the to a CRT projector. Refer to documentati to ctinue the installati. RGsB/RGBS Comp/H-Sync -Sync Port 1 ideo Projector Mode Green: Operati Red: Standby Power/Mains Comm Port Port 3 R G B Port 1 S-ideo Off On Off 9-Pin Female Black Yellow Red Green Blue RGsB/RGBS/RGBH 5 7 BR COM 9-Pin Female 6 CC 50'/100' /02 H/ R G B CRT Cnectis. See page 2-5 for cabling guidelines. Extr Page 2

4 xi Series LCD Projector Cnectis Use the following illustratis as a guide when cnecting the to a LCD projector. Refer to documentati to ctinue the installati. Br Com 3, 4 or 5 BNC INPUT 1 INPUT 2 INPUT 3 INPUT 4 OUTPUT H/H H/H H/H H/H PJ COMM H/H AUDIO AUDIO AUDIO AUDIO AUDIO RS 232 LCD Cnectis. See page 2-5 for cabling guidelines. Extr Page 3

5 xi Series 6300 Projector Cnectis Use the following illustratis as a guide when cnecting the to a 6300 projector. Refer to documentati to ctinue the installati. Br Com 3, 4 or 5 BNC INPUT 1 INPUT 2 INPUT 3 INPUT 4 OUTPUT H/H H/H H/H H/H PJ COMM H/H AUDIO AUDIO AUDIO AUDIO AUDIO RS Cnectis. See page 2-5 for cabling guidelines. Extr Page 4