2-12. General Principles 2-Opto-electronics Safety Switches Operator. Interface. Logic Power

Transcription

1 Safety Light Curtains Overview Components equired for PAC with Muting, see Figure :. Optic heads (operate on 2V DC) with muting module ordered as a pair (transmitter/receiver) 2. It is also possible to use other Allen-Bradley Guardmaster muting modules such as the MS2 or the MS22LM muting module. supply. Cables for light curtains 5. Muting indication 6. Sensors for muting 7. Sensor accessories 8. Sensor cordsets Work Piece Work Piece MS22LM Work Piece oller Work Path MS22LM or MS2 Supply oller Work Path Supply Work Piece Perimeter Access Control Overview Typical System Configurations The Allen-Bradley Guardmaster Safe PAC safety light curtain system is a two box design. This means the safety light curtain does not need a separate controller to operate in a guard-only mode. Therefore, the safety outputs the light curtain (OSSDs) can be connected directly to any safety relay that will accept PNP inputs. The following are some common configurations light curtain systems. The numbers on the drawing indicate the ordering steps to follow to ensure that a complete system is specified. Components required for a multiple-beam Safe PAC, see Figure 5:. Optic heads (operate on 2V DC) ordered as a pair (transmitter/receiver) 2. Cables 5-pin cables for transmitter and receiver. Safety relay. supply 20V AC to 2V DC 5. Mounting brackets minimum per optic head pair 6. Corner mirror columns (for multiple side protection) 7. Mounting stand if required Figure

2 General Description Standard The Allen-Bradley Guardmaster safety light curtain is an economical, fully featured, Type safety light curtain in a uniquely styled housing. safety light curtains are general-purpose presence sensing devices designed for use on hazardous machinery providing point operation, as well as perimeter and access guarding. This self-contained, two-box, safety light curtain has DIP-switch selectable operating modes and is available in both mm and 0 mm resolutions. Modes operation such as fixed and floating blanking, beam coding, start/restart interlock, external device monitoring (EDM), and machine test signal, are selected by DIP-switch settings. These DIPswitches are located beneath a security door, which are conveniently located on both the transmitter and receiver end caps. The s torsionally rigid, extruded aluminium, polyurethane powder-coated housing, combined with an environmental rating IP65, allows the to be used in guarding applications across a broad range industries. emote Teach The emote Teach system provides a remote means changing a fixed blanking configuration within the safety light curtain. This keyswitch box eliminates the need to open the receiver door and perform the Teach function. The three-position key switch simulates the opening the receiver door, teaching the light curtain the new fixed blanking area, closing the door and returning to the run mode operation. The IP65 rated key switch box is provided with a steel mounting back plate to facilitate mounting the box in proximity to the receiver. It is necessary to see the receiver LEDs when performing the teach function. Cascadable System A cascadable safety light curtain is a standard safety light curtain in and 0 mm resolutions with additional M2 connectors located on top each safety light curtain. The connector on the top the safety light curtains allow the interconnection up to a total three pair safety light curtains with a common pair OSSDs. The ability to interconnect pairs reduces overall system wiring and simplifies the safety circuit resulting in a lower overall cost a multiple safety light curtain system. This product configurability also allows a safety light curtain system to protect multiple sides a machine or simply adds flexibility when positioning in various applications. The complete cascading system has the full functionality a standard (beam coding, EDM, start/restart interlock, fixed and floating blanking). There are a couple operating modes which can not be configured in the middle and end segments (EDM and Start/estart Interlock) and must only be configured in the host (first) pair. The system will still have these operating modes active if configured in the host or first pair. This host or first pair is the pair cascading light curtains, which have the output cordsets connected and wired to the safety relay, safety PLC or FSDs. Configuring the EDM operating mode in the end and middle segments will cause the system to go to a lock-out condition after the first interruption the sensing field. Configuration the start/restart interlock operating mode in the end and middle segments will cause the system to stay in a red condition awaiting reset after the interruption the sensing field. The cascading safety light curtains are ordered as pairs (transmitter and receiver) and are shipped under one cat. no. After selecting the appropriate pair cat. nos. for a cascading system, select the interconnecting transmitter and receiver patchcord cat. nos. to connect the pairs. The transmitter patchcord is a -pin M2 patchcord fered in lengths / meter, meter and 2 meters. The receiver patchcord is an 8-pin M2 patchcord fered in lengths / meter, meter, and 2 meters. If the end pair a cascading system is a cascading pair light curtains, it is necessary to attach a termination adaptor to the top M2 connector located on the receiver. Be sure to order all other required interfaces and accessories. Principles 2-Opto-electronics Safety Switches Operator Logic 2-

3 Last segment pair can be cascading or standard pair Patchcord (2 meter max. length) Up to three POC segments can be interconnected. The upper and lower limit the protective field is shown by markings on the housings. The width the protective field is derived from the length the light path between transmitter and receiver and must not exceed the maximum rated width the protective field: 7 m for mm (22.9 ft for 0.55 in.), 8 m for 0 mm (59.0 ft for.8 in.). Cascading segments are fered in protective heights from mm in both mm and 0 mm resolutions. Cascading segments 60 mm are not fered, however; a 60 mm can be used as the last segment in a cascading system. A maximum three light curtains can be interconnected with a common pair OSSDs. The maximum number beams allowed in a cascading system is 528 beams, which equates to three 760 mm cascading s in mm resolution. The individual segments can have mixed resolutions, e.g., mm and 0 mm as long as the pairs have the same protective heights and resolutions. The response time a cascading system is the longest response time any pair in the cascading system. For example, if the response time each pair in the cascading system is 20 ms, then the cascading system's response time is 20 ms. Cascading segments can be used as standalone light curtain pairs or can have up to three segments interconnected. These cascading segments all function as independent light curtains. IMPOTANT When cascading segments are used as standalone pairs or as the last segment in a cascading system, it is necessary to use a termination plug on the top connector the cascading receiver. It is also possible to use a standard Type POC pair as the last segment in a cascading system. with Integrated Laser Alignment System The POC and POC cascadable light curtains are fered with an integrated laser alignment system consisting a Class, eye safe, constantly powered laser located in the top the transmitter and at the bottom the receiver. There are targets located across from each laser that help facilitate alignment the light curtain when the laser is emitting visible light. Each laser emits a low level visible light. Simply placing a finger or opaque object in front the laser reflects the laser light back to a photo sensor. This photo sensor causes the laser to switch state from a barely visible low level emission to a higher level emission visible light. Interrupting the visible light below the finger symbol will cause the laser to change state back to a low level light emission. The visible light will also change to a low level after five minutes. The Integrated Laser Alignment system also quickly helps with the re-alignment pairs when units are knocked out alignment during the course the work process or when corner mirrors are used. The and Cascadable are fered in and 0 mm resolutions in protective heights from 20 to 600 mm. The 60 and 760 mm protective heights are not fered with the integrated laser alignment systems. ArmorBlock Guard I/O Connectivity The POC and Cascadable light curtains are also fered with the Class, eye safe, integrated laser alignment system and connectivity to ArmorBlock Guard I/O. The receiver these light curtains has a five-pin M2 quick-disconnect connector wired to connect to the 72DS ArmorBlock I/O module, allowing the s OSSDs to operate over a DeviceNet Safe network. This version the has limited configurability, i.e., only beam coding, fixed and floating blanking can be configured by setting the appropriate DIP switches and performing the teach function. EDM, Start/estart interlock, and the auxiliary output are not available in these models. You can use the ArmorBlock Guard I/O with any safety controller that communicates on DeviceNet using CIP Safety for the control and monitoring safety circuits. ArmorBlock Guard I/O detects circuit failures at each I/O point while providing detailed diagnostics directly to the controller. With CIP Safety, you can easily integrate safety and standard control systems by using safety and standard messages on the same wire. The 72DS ArmorBlock Guard I/O family consists 2V DC digital I/O modules that communicate on DeviceNet networks. 2-

4 Features Standard Fixed blanking teachable Floating blanking One-beam floating blanking on 0 mm resolution Two-beam floating blanking on mm resolution Beam coding External Device Monitoring (EDM) Start/restart interlock M2 quick-disconnect connectors 60 to 760 mm in 60 mm increments Standard can be used as last segment pair in a cascading system Standard with Integrated Laser Alignment Fixed blanking teachable Floating blanking Beam coding M2 quick-disconnect connectors Ease alignment at installation with visible laser alignment mm in 60 mm increments and 0 mm resolutions emote Teach Three-position momentary key switch IP65 rated key switch box Y connector for quick-disconnect connections Standard cables Allows quick and efficient reteaching fixed blanked areas 60 to 760 mm in 60 mm increments Cascadable System Easy to interconnect light curtains up to three 760 mm segment pairs No increase in system response time ArmorBlock Guard I/O Fixed blanking teachable Floating blanking Up to three cascading pairs can connect to ArmorBlock Guard I/O Beam coding M2 quick-disconnect connectors DeviceNet safe network connectivity mm in 60 mm increments Specifications Safety atings IEC/EN 696 Parts & 2, UL 696 Standards Parts & 2, UL 998 Type per IEC/EN696. Category Safety Classification device per EN 95-, SIL per IEC 6508, PLe per EN/ISO 89 culus, UL 696, UL 998, TÜV, and CE Certifications Marked for all applicable directives Supply Input, Max. 2V DC ±20% Maximum esidual ipple 0.05 Vss Consumption 0. A max (no load) Outputs Safety Outputs 2 OSSD, 0.5 A, short-circuit protected Non-Safety Outputs Auxiliary output, 0.5 A max. Output Voltage, Min. (Uv) - 2V Switching Voltage, 500 2V DC Min. Operating Characteristics esponse Time mm; 60 mm 0 mm 20 ms, 600 mm and 760 mm, 25 ms. 0 mm; 20 ms. Add 0 ms when beam coding activated. Status Indicators ON State, OFF State, Blanking, Alignment, Interlock Protected Height See Product Selection tables. (0.55) or 0 (.8) Scanning ange/ Synchronization Wavelength Environmental Enclosure Type ating elative Humidity Operating Temperature [C (F)] Vibration Shock Physical Characteristics Mounting Weight Housing Cross Section Connection Type Cable Length 0. 7 m / mm ( ft / 0.55 in.) 0. 6 m / 0 mm ( ft /.8 in.) Optical, first beam adjacent to LEDs. 870 nm IP % (noncondensing) ( ) IEC : Frequency 0 55 Hz; Amplitude: 0.5 mm (0.0 in.) IEC : Acceleration 0 g, pulse duration 6 ms 0 55 Hz End-cap brackets supplied Varies by protective height 0 mm x 50 mm (.57 in. x.96 in.) Transmitter: -pin M2 micro QD; eceiver: 8-pin M2 micro QD 0 m (00 ft) max. General Principles 2-Opto-electronics Safety Switches Operator Logic 2-5

5 Product Selection Standard System The Allen-Bradley Guardmaster safety light curtains are ordered as pairs transmitter and receiver and shipped under one cat. no. After selecting the appropriate light curtain pair, ensure that required interfaces and accessories are ordered. Protected Height Protected Height 60 (6.) (0.55) 6 0L-PJ060YD 60 (6.) 0 (.8) 8 0L-PK060YD 20 (2.6) (0.55) 2 0L-PJ020YD 20 (2.6) 0 (.8) 6 0L-PK020YD 80 (8.9) (0.55) 8 0L-PJ080YD 80 (8.9) 0 (.8) 2 0L-PK080YD 60 (25.2) (0.55) 6 0L-PJ060YD 60 (25.2) 0 (.8) 2 0L-PK060YD 800 (.5) (0.55) 80 0L-PJ0800YD 800 (.5) 0 (.8) 0 0L-PK0800YD 960 (7.8) (0.55) 96 0L-PJ0960YD 960 (7.8) 0 (.8) 8 0L-PK0960YD 20 (.) (0.55) 2 0L-PJ20YD 20 (.) 0 (.8) 56 0L-PK20YD 280 (50.) (0.55) 28 0L-PJ280YD 280 (50.) 0 (.8) 6 0L-PK280YD 0 (56.7) (0.55) 0L-PJ0YD 0 (56.7) 0 (.8) 72 0L-PK0YD 600 (6.0) (0.55) 60 0L-PJ600YD 600 (6.0) 0 (.8) 80 0L-PK600YD 760 (69.) (0.55) 76 0L-PJ760YD 760 (69.) 0 (.8) 88 0L-PK760YD Note: The transmitter requires a -pin cable and the receiver requires an 8-pin cable. Note: To select just a transmitter or receiver, replace the "P" in the above cat. nos. with a "T" for transmitter and an "" for receiver. emote Teach System The Allen-Bradley Guardmaster remote teach system is ordered as a system. The system consists a standard transmitter in either mm or 0 mm resolutions with mounting hardware, a receiver with a 0 inch Y-connector cable, a metal key switch box, and a -pin 2 meter patchcord which connects between the key switch box and the Y-connector. Protected Height Protected Height 60 (6.) (0.55) 6 0L-SJ060Y 60 (6.) 0 (.8) 8 0L-SK060Y 20 (2.6) (0.55) 2 0L-SJ020Y 20 (2.6) 0 (.8) 6 0L-SK020Y 80 (8.9) (0.55) 8 0L-SJ080Y 80 (8.9) 0 (.8) 2 0L-SK080Y 60 (25.2) (0.55) 6 0L-SJ060Y 60 (25.2) 0 (.8) 2 0L-SK060Y 800 (.5) (0.55) 80 0L-SJ0800Y 800 (.5) 0 (.8) 0 0L-SK0800Y 960 (7.8) (0.55) 96 0L-SJ0960Y 960 (7.8) 0 (.8) 8 0L-SK0960Y 20 (.) (0.55) 2 0L-SJ20Y 20 (.) 0 (.8) 56 0L-SK20Y 280 (50.) (0.55) 28 0L-SJ280Y 280 (50.) 0 (.8) 6 0L-SK280Y 0 (56.7) (0.55) 0L-SJ0Y 0 (56.7) 0 (.8) 72 0L-SK0Y 600 (6.0) (0.55) 60 0L-SJ600Y 600 (6.0) 0 (.8) 80 0L-SK600Y 760 (69.) (0.55) 76 0L-SJ760Y 760 (69.) 0 (.8) 88 0L-SK760Y emote Teach Keyswitch Box Assembly 0L-M8600 DC Micro Style Quick-Disconnect Patchcord, -Pin 889D-FACDM-2 Note: The transmitter requires a -pin cable and the receiver requires an 8-pin cable. Note: The remote teach system light curtains can be ordered as pairs by replacing the "S" in the cat. no. a with "P." Included with each system cat. no.; can be ordered as a replacement part. 2-6

6 Cascadable Standard System Protected Height Protected Height 20 (2.6) (0.55) 2 0L-CJ020YD 20 (2.6) 0 (.8) 6 0L-CK020YD 80 (8.9) (0.55) 8 0L-CJ080YD 80 (8.9) 0 (.8) 2 0L-CK080YD 60 (25.2) (0.55) 6 0L-CJ060YD 60 (25.2) 0 (.8) 2 0L-CK060YD 800 (.5) (0.55) 80 0L-CJ0800YD 800 (.5) 0 (.8) 0 0L-CK0800YD 960 (7.8) (0.55) 96 0L-CJ0960YD 960 (7.8) 0 (.8) 8 0L-CK0960YD 20 (.) (0.55) 2 0L-CJ20YD 20 (.) 0 (.8) 56 0L-CK20YD 280 (50.) (0.55) 28 0L-CJ280YD 280 (50.) 0 (.8) 6 0L-CK280YD 0 (56.7) (0.55) 0L-CJ0YD 0 (56.7) 0 (.8) 72 0L-CK0YD 660 (6.0) (0.55) 60 0L-CJ600YD 600 (6.0) 0 (.8) 80 0L-CK600YD 760 (69.) (0.55) 76 0L-CJ760YD 760 (69.) 0 (.8) 88 0L-CK760YD Note: Cascadable systems are sold in pairs represented by the "C" in the cat. no. To order the cascadable transmitter or receiver, replace the "C" with a "G" for the transmitter or "F" for the receiver. with Integrated Laser Alignment Protected Height Protected Height 20 (2.6) (0.55) 2 0L-PJL020YD 20 (2.6) 0 (.8) 6 0L-PKL020YD 80 (8.9) (0.55) 8 0L-PJL080YD 80 (8.9) 0 (.8) 2 0L-PKL080YD 60 (25.2) (0.55) 6 0L-PJL060YD 60 (25.2) 0 (.8) 2 0L-PKL060YD 800 (.5) (0.55) 80 0L-PJL0800YD 800 (.5) 0 (.8) 0 0L-PKL0800YD 960 (7.8) (0.55) 96 0L-PJL0960YD 960 (7.8) 0 (.8) 8 0L-PKL0960YD 20 (.) (0.55) 2 0L-PJL20YD 20 (.) 0 (.8) 56 0L-PKL20YD 280 (50.) (0.55) 28 0L-PJL280YD 280 (50.) 0 (.8) 6 0L-PKL280YD 0 (56.7) (0.55) 0L-PJL0YD 0 (56.7) 0 (.8) 72 0L-PKL0YD 600 (6.0) (0.55) 60 0L-PJL600YD 600 (6.0) 0 (.8) 80 0L-PKL600YD Note: s are sold in pairs. To select a transmitter or receiver, replace the "P" in the cat. no. with a "T" for transmitter and an "" for receiver. Cascadable with Integrated Laser Alignment Protected Height Protected Height 20 (2.6) (0.55) 2 0L-CJL020YD 20 (2.6) 0 (.8) 6 0L-CKL020YD 80 (8.9) (0.55) 8 0L-CJL080YD 80 (8.9) 0 (.8) 2 0L-CKL080YD 60 (25.2) (0.55) 6 0L-CJL060YD 60 (25.2) 0 (.8) 2 0L-CKL060YD 800 (.5) (0.55) 80 0L-CJL0800YD 800 (.5) 0 (.8) 0 0L-CKL0800YD 960 (7.8) (0.55) 96 0L-CJL0960YD 960 (7.8) 0 (.8) 8 0L-CKL0960YD 20 (.) (0.55) 2 0L-CJL20YD 20 (.) 0 (.8) 56 0L-CKL20YD 280 (50.) (0.55) 28 0L-CJL280YD 280 (50.) 0 (.8) 6 0L-CKL280YD 0 (56.7) (0.55) 0L-CJL0YD 0 (56.7) 0 (.8) 72 0L-CKL0YD 600 (6.0) (0.55) 60 0L-CJL600YD 600 (6.0) 0 (.8) 80 0L-CKL600YD Note: Cascadable s are sold in pairs. To select a transmitter or receiver, replace the "C" with a "G" for cascadable transmitter and an "F" for a cascadable receiver. General Principles 2-Opto-electronics Safety Switches Operator Logic 2-7

7 with Integrated Laser Alignment and ArmorBlock Guard I/O Connectivity Protected Height Protected Height 20 (2.6) (0.55) 2 0L-PJL020YA 20 (2.6) 0 (.8) 6 0L-PKL020YA 80 (8.9) (0.55) 8 0L-PJL080YA 80 (8.9) 0 (.8) 2 0L-PKL080YA 60 (25.2) (0.55) 6 0L-PJL060YA 60 (25.2) 0 (.8) 2 0L-PKL060YA 800 (.5) (0.55) 80 0L-PJL0800YA 800 (.5) 0 (.8) 0 0L-PKL0800YA 960 (7.8) (0.55) 96 0L-PJL0960YA 960 (7.8) 0 (.8) 8 0L-PKL0960YA 20 (.) (0.55) 2 0L-PJL20YA 20 (.) 0 (.8) 56 0L-PKL20YA 280 (50.) (0.55) 28 0L-PJL280YA 280 (50.) 0 (.8) 6 0L-PKL280YA 0 (56.7) (0.55) 0L-PJL0YA 0 (56.7) 0 (.8) 72 0L-PKL0YA 600 (6.0) (0.55) 60 0L-PJL600YA 600 (6.0) 0 (.8) 80 0L-PKL600YA Note: s are sold in pairs. To select a transmitter or receiver, replace the "P" in the cat. no. with an "" for a receiver. The standard transmitter is used in the pair. To order a transmitter, replace the "P" with a "T" and the "A" with a "D." Cascadable with Integrated Laser Alignment and ArmorBlock Guard I/O Connectivity Protected Height Protected Height 20 (2.6) (0.55) 2 0L-CJL020YA 20 (2.6) 0 (.8) 6 0L-CKL020YA 80 (8.9) (0.55) 8 0L-CJL080YA 80 (8.9) 0 (.8) 2 0L-PKL080YA 60 (25.2) (0.55) 6 0L-CJL060YA 60 (25.2) 0 (.8) 2 0L-CKL060YA 800 (.5) (0.55) 80 0L-CJL0800YA 800 (.5) 0 (.8) 0 0L-CKL0800YA 960 (7.8) (0.55) 96 0L-CJL0960YA 960 (7.8) 0 (.8) 8 0L-CKL0960YA 20 (.) (0.55) 2 0L-CJL20YA 20 (.) 0 (.8) 56 0L-CKL20YA 280 (50.) (0.55) 28 0L-CJL280YA 280 (50.) 0 (.8) 6 0L-CKL280YA 0 (56.7) (0.55) 0L-CJL0YA 0 (56.7) 0 (.8) 72 0L-CKL0YA 600 (6.0) (0.55) 60 0L-CJL600YA 600 (6.0) 0 (.8) 80 0L-CKL600YA Note: Cascadable s are sold in pairs. To select a transmitter or receiver replace the "C" with an "F" for a cascadable receiver. The cascadable standard transmitter is used in these pairs. To order a cascadable transmitter, replace the "C" with a "G" and the "A" with a "D" to specify the appropriate transmitter cat. no. ecommended Logic s Description Safety Outputs Auxiliary Outputs Terminals eset Type Supply Cat. Page No. Single-Function Safety elays for 2 N.C. Contact Switch MS27P N.O. N.C. MS27TP N.O. N.C. emovable (Screw) emovable (Screw) Monitored Manual 2V AC/DC N25 Auto./Manual 2V AC/DC N22 MS26 2 N.O. None Fixed Auto./Manual 2V AC/DC N27 Modular Safety elays MS20P Base 2 N.C. only 2 N.O. N.C. and 2 PNP Solid State emovable MS2 2 N.O. N.C. emovable MS0P Base MS20P Input Module Muting Modules MS00 Series Output Modules PNP Solid State emovable Auto./Manual or Monitored Manual Auto./Manual or Monitored Manual Auto./Manual Monitored Manual 2 PNP Solid State emovable 2V DC from the base unit 2V DC from the base unit H H277 2V DC W229 2V DC from the base unit W228 MS22LM 2 N.O. N.C. emovable Auto./Manual 2V DC P207 MS2 (requires optical interface to configure 5L-AF650 2 PNP 2 PNP, configurable emovable Auto./manual or manual monitored 2V DC P226AGS-NN 2-8

8 Standard and emote Teach Cordsets Two equired (one for transmitter and one for receiver) Female Connector (Sensor End) Face View Female Connector Style Pin/Wire Color Wire ating Length [m (ft)] Transmitter 7 eceiver Straight Female Straight Female Brown 2 White Blue Black White 2 Brown Green Yellow 5 Grey 6 Pink 7 Blue 8 ed Cable 22 AWG 00V A 2 AWG 0V AC/6V DC.5 A 2 (6.56) 889D-FAC-2 5 (6.) 889D-FAC-5 0 (2.8) 889D-FAC-0 5 (9.2) 889D-FAC-5 20 (65.6) 889D-FAC-20 0 (98.) 889D-FAC-0 2 (6.56) 889D-F8AB-2 5 (6.) 889D-F8AB-5 0 (2.8) 889D-F8AB-0 5 (9.2) 889D-F8AB-5 20 (65.6) 889D-F8AB-20 0 (98.) 889D-F8AB-0 General Principles Cascadable System Patchcords to connect cascadable system The transmitter host patchcord has -pin DC micro over-molded quick-disconnect connectors fered in lengths / m, m, and 2 m. The receiver host patchcord has 8-pin DC micro over-molded quick-disconnect connectors fered in lengths / m, m, and 2 m. Face View Female Description Transmitter Patchcord 2 -pin M2 patchcord, 0. m (2 in.) 889D-FACDM-0M -pin M2 patchcord, m (9.7 in.) 889D-FACDM- -pin M2 patchcord, 2 m (78.7 in.) 889D-FACDM-2 eceiver Patchcord 2 8-pin M2 patchcord, 889D-F8ABDM-0M 0. m (2 in.) 8 8-pin M2 patchcord, m 889D-F8ABDM- (9.7 in.) 7 8-pin M2 patchcord, 2 m 6 5 (78.7 in.) 889D-F8ABDM-2 Face View Female Description eceiver Termination Plug Termination plug 8-pin M2 8 quick disconnect 2 7 equired for connection to 898D-8CU-DM top connector cascadable receiver if cascade light 6 curtain is used as a standalone system or as the last segment pair in a 5 cascaded system. Note: A termination plug is not necessary for the cascadable transmitter. Cordsets Approximate Dimensions Dimensions are not intended to be used for installation purposes. (0.56) 7 (.85) Straight Female M2 Quick Disconnect ArmorBlock Guard I/O Top View Color No. Pins Signal eceiver Brown +2V White 2 OSSD 2 Blue 0V Black OSSD Grey 5 NC Interconnecting Patchcords ArmorBlock I/O Connection Description 889D-F5ACDM-0M Five-pin M2 patchcord, 0. m (2 in.) 889D-F5ACDM- Five-pin M2 patchcord, m (9.7 in.) 889D-F5ACDM-2 Five-pin M2 patchcord, 2 m (78.7 in.) 889D-F5ACDM-5 Five-pin M2 patchcord, 5 m (96.85 in.) 889D-F5ACDM-0 Five-pin M2 patchcord, 0 m (9.7 in.) Note: The pairs with ArmorBlock Guard I/O Connectivity have a 5-pin M2 quick-disconnect connector on the receiver wired to allow connection to the ArmorBlock 5-pin connector. The transmitter in that pair is a standard transmitter with integrated laser alignment system fered with a -pin M2 quick-disconnect connector. It is possible to connect either a standard -pin M2 cordset or the 5-pin M2 quick-disconnect connector cordset or patchcord to this transmitter. 2-Opto-electronics Safety Switches Operator Logic 2-9

9 Termination Connector for Cascadable eceiver (if it's a standalone pair) with ArmorBlock Guard I/O Connectivity Face View Female Description pin M2 Termination Adaptor Note: The cascadable with ArmorBlock Guard I/O connectivity can be used as a standalone pair if the top connector on the receiver has a termination adaptor connected. The cascadable transmitter does not require a termination adaptor. Optional Accessories Description Steel L-shaped end cap mounting bracket ( per package) Note: brackets supplied with each pair. Aluminum middle mounting bracket for vibratory applications supply: Output 2V DC, Amps, 72 W Laser alignment tool laser alignment tool bracket Mounting stand Vertical shock mount kit Horizontal shock mount kit Middle vertical mount kit Middle horizontal mount kit weld shield (cat. no. is for a pair light curtains) Washdown Enclosure Kit Note: Only for use with standard light curtain. 8-pin M2 eceiver Termination Plug (equired for top receiver connector if a cascaded pair is used as a standalone or if it is the last pair in a cascaded system.) 0L-AF60 0L-AF XLP72E 0L-ALAT 0L-AF609 0L-AMSTD 0L-AF620 0L-AF62 0L-AF622 0L-AF62 0L-AGWS060 0L-AGWS020 0L-AGWS080 0L-AGWS060 0L-AGWS0800 0L-AGWS0960 0L-AGWS20 0L-AGWS280 0L-AGWS0 0L-AGWS600 0L-AGWS760 0L-AGST20 0L-AGST80 0L-AGST60 0L-AGST800 0L-AGST D-8CU-DM 898D-8U-DM 2-20

10 Cascadable eceiver with Integrated Laser Alignment (0.) 2 (.65) 52 (2.05) 80 min (.) 0 (.57) A Middle Mounting Bracket To Be Used in Vibration Applications Cascadable Transmitter with Integrated Laser Alignment 2 (.25) B C 20 0 (0.79) (.575) Type A Protective Height B Mounting C Total Length D Mounting 0L-C*L020YD 20± ± L-C*L080YD 80± ± L-C*L060YD 60± ± L-C*L0800YD 800± ± L-C*L0960YD 960± ± L-C*L20YD 20± ± L-C*L280YD 280± ± L-C*L0YD 0± ± L-C*L600YD 600± ± J = mm resolution, K = 0 mm resolution 75 (2.95) 80 min (.) 0L-FJL020YD shown receiver 0L-GJL020YD shown transmitter 0L-CJL020YD shown * K = 0 mm resolution * J = mm resolution * L = Laser 2-2