2016 ADJ Products, LLC ADJ Products, LLC User Instructions

Transcription

1 2016 ADJ Products, LLC all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-adj Products, LLC brands and product names are trademarks or registered trademarks of their respective companies. ADJ Products, LLC and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, unsufficient and negligent assembly, installation, rigging, and operation of this product. 8/16 User Instructions Europe Energy Saving Notice Energy Saving Matters (EuP 2009/125/EC) Saving electric energy is a key to help protecting the enviroment. Please turn off all electrical products when they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power when not in use. Thank you!

2 Introduction Unpacking: Thank you for purchasing the by ADJ Products, LLC. Every has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit has arrived intact. In the case damage has been found or parts are missing, please contact our toll free customer support number for further instructions. Do not return this unit to your dealer without first contacting customer support. Introduction: The is part of ADJ s continuing pursuit for creating high quality affordable intelligent fixtures. The Mini Dekker LZR is a DMX intelligent LED mooflower effect with laser. This fixture can be used in a stand alone mode or connected in a Master/ Slave configuration. This fixture has three operating modes: Sound Active mode, Show mode, and DMX control. Customer Support: ADJ Products, LLC provides a toll free customer support line, to provide set up help and to answer any question should you encounter problems during your set up or initial operation. You may also visit us on the web at for any comments or suggestions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m. Pacific Standard Time. Voice: (800) Fax: (323) support@americandj.com To purchase parts online visit Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture. Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact ADJ. PLEASE recycle the shipping carton when ever possible. General Instructions To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations of this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit, for future reference. Features Includes Hanging Yoke 3 Operating Modes: Show Mode, Sound Active, & DMX Control Light Weight Strobing Electronic Dimming 0-100% Built in Microphone DMX-512 protocol 2 DMX Channel Modes: 2 Channels & 7 Channels Warranty Registration The carries a 1 Year limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight prepaid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well as the R.A. number must also be written down on a piece of paper and included in the shipping container. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by contacting customer support at (800) ADJ Products, LLC Instruction Manual Page 2 ADJ Products, LLC Instruction Manual Page 3

3 Safety Precautions To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit. Be sure that the local power outlet match that of the required voltage for your unit. Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short. Disconnect from main power before making any type of connection. Do not remove the cover under any conditions. There are no user serviceable parts inside. Never operate this unit when it s cover is removed. Never plug this unit in to a dimmer pack Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6 (15cm) between this device and a wall. Do not attempt to operate this unit, if it becomes damaged. This unit is intended for indoor use only, use of this product out` doors voids all warranties. During long periods of non-use, disconnect the unit s main power. Always mount this unit in safe and stable matter. Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to the point they exit from the unit. Cleaning -The fixture should be cleaned only as recommended by t he manufacturer. See page 11 for cleaning details. Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (includ ing amplifiers) that produce heat. The fixture should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged. B. Objects have fallen, or liquid has been spilled into the appliance. C. The appliance has been exposed to rain or water. D. The appliance does not appear to operate normally or exhibits a marked change in performance. DMX Set Up Power Supply: The ADJ contains a automatic voltage switch, which will auto sense the voltage when it is plugged into the power source. With this switch there is no need to worry about the correct power voltage, this unit can be plugged in anywhere. DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures (most controllers only have a DATA OUT terminal). DMX Linking: DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain. Data Cable (DMX Cable) Requirements (For DMX Operation): The has two DMX channel modes; a 2 channel mode and 7 channel mode. The DMX address is set electronically using the controls on the rear panel of the unit. Your unit and your DMX controller require a approved DMX Ohm Data cable for data input and data output. We recommend Accu-Cable DMX cables. If you are making your own cables, be sure to use standard Ohm shielded cable (This cable may be purchased at almost all professional sound and lighting stores). Your cables should be made with a male and female XLR connector on either end of the cable. Also remember that DMX cable must be daisy chained and cannot be split. ADJ Products, LLC Instruction Manual Page 4 ADJ Products, LLC Instruction Manual Page 5 Figure 1

4 DMX Set Up Notice: Be sure to follow figures two and three when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing. Grounding the shield could cause a short circuit and erratic behavior. DMX512 O T 3-PIN XLR COMMON DMX + DMX - XLR Male Socket XLR Female Socket 1 Ground 2 Cold 2 Cold 1 Ground DMX512 IN 3-PIN XLR Figure 2 XLR Pin Configuration Pin 1 = Ground Layout American Version 3 Hot 3 Hot Pin 2 = Data Compliment (negative) Pin 3 = Data True (positive) Figure 3 Special Note: Line Termination. When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems and interference. It is always advisable to connect a DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (DMX-) and PIN 3 (DMX +) of the last fixture. Figure 4 5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX- 512 data cables for DATA transmission in place of 3-pin. 5-pin DMX fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a proper cable conversion. Conductor Ground/Shield Data Compliment (- signal) Data True (+ signal) Not Used Not Used 3-Pin XLR to 5-Pin XLR Conversion 3-Pin XLR Female (Out) Pin 1 Pin 2 Pin 3 5-Pin XLR Male (In) Pin 1 Pin 2 Pin 3 Do Not Use Do Not Use Function Display: Used to show the various menus and the selected functions. 2. Button: MENU UP DOWN ENTER To select the programming functions To go forward in the selected functions To go backward in the selected functions To confirm the selected functions 3. DMX IN/OUT: For DMX512 links, use 3 pin XLR plug cable to link the unit together. 4. POWER IN: Used to connect to supply power. 5.Key for Laser: To turn on/off the laser Led. (Only for EU version) 5 Europe Version ADJ Products, LLC Instruction Manual Page 6 ADJ Products, LLC Instruction Manual Page 7

5 Laser Warning Labels System Menu SPEC American Version DMX Address 2 ADJ专用FDA授权号码标签贴法图 1 使用警告标签贴法图 SPEC Channel Mode Manufactured: Show Mode 3 出光口标签贴法图 SPEC A.D.J Supply Europe B.V Junostraat 2,6468 EW Kerkrade, Netherlands Show Speed Q.C.passe SPEC Slave Mode 警告贴纸贴法图 Sound State 安全警告贴纸贴法图 Sound Sense Europe Version MENU Master Mode A.D.J Supply Europe B.V Junostraat 2,6468 EW Kerkrade, Netherlands ADJ专用FDA授权号码标签贴法图 LS-01RG 1 使用警告标签贴法图 Manufactured: 参考贴法图 Blackout Mode SPEC Hold Last state ADJ LS-03RG A.D.J Supply Europe B.V Junostraat 2,6468 EW Kerkrade, Netherlands Manufactured: Led 3 出光口标签贴法图 Strobe Auto Test Q.C.passed A.D.J Supply Europe B.V Junostraat 2,6468 EW Kerkrade, Netherlands Manufactured: Display Inversion SPEC 警告贴纸贴法图 Fixture Hours Software Version 安全警告贴纸贴法图 ADJ Products, LLC Instruction Manual Page 8 Reset ADJ Products, LLC Instruction Manual Page 9 参考贴法图 ADJ LS-01RG I LS-03RG I

6 System Menu System Menu System Menu: When making adjustments press ENTER to confirm your setup then press and hold the MENU button for at least 3 seconds. To exit without making any adjustments press the MENU button. The display will lock after 30 seconds, press the MENU button for 3 seconds to unlock. ADDR - DMX Address Setting. 1. Press the either the MENU, UP, or DOWN buttons until ADDR is displayed, press ENTER. 2. The current address will now be displayed and flashing. Press the UP or DOWN buttons to find your desired address. Press ENTER to set your desired DMX address. CHND - This will let select your desired DMX channel mode. 1. Press the MENU button until CHND is displayed, press ENTER. The current DMX channel mode will be displayed 2. Press the UP or DOWN buttons to find your desired DMX channel mode and press ENTER to confim and exit. SHND - Show modes 0-2 (Factory programs). 1. Press the MENU button until SHND is displayed, press ENTER. 2. Sh X will now be displayed, X representing a number between 0-6. Shows 1-2 are factory programs, while show 0 is random mode. Use the UP or DOWN buttons to find your desired show. 3. When you have found your desired show press ENTER, then press and hold the MENU button for at least 3 seconds to activate. After you have set your desired show, it can be changed at any time using the UP or DOWN buttons. SPEE - Show mode speed. 1. Press the MENU button until SPEE is displayed, press ENTER. ADJ Products, LLC Instruction Manual Page A number between will now be displayed, the number is the current speed setting. Use the UP or DOWN buttons to adjust the show speed. 0 being the slowest speed and 100 being the fastest. 3. Press ENTER to set the speed then press and hold the MENU button for at least 3 seconds to show mode. SLND - This will let you set unit as a master or slave in a master/slave configuration. 1. Press the MENU button until SLND is displayed, press ENTER. Either MAST, SL 1, or SL 2 will be displayed. 2. Press the UP or DOWN buttons until your desired setting is displayed, press ENTER to confim. Note: In a Master/Slave configuration you can set one fixture to Master and then set the next fixture to SL 2, the fixtures will now have contrast movement to each other. SOUN - Sound Active mode. 1. Press the MENU button until SOUN is displayed, press ENTER. 2. The display will show either ON or OFF. Press the UP or DOWN buttons to select ON to activate sound active mode, or OFF to deactivate sound active mode. 3. Press ENTER to confirm. SOSE - In this mode you can adjust the sound sensitivity. 1. Press the MENU button until SOSE is displayed, press ENTER. 2. A number between will be displayed. Press the UP or DOWN buttons to adjust the sound sensitivity. 0 being the least sensitive, and 100 being the most sensitive. 3. When you have found your desired setting press ENTER to confirm. ADJ Products, LLC Instruction Manual Page 11

7 System Menu System Menu NODN - This mode can be used as a precaution mode, TEST - This function will run a self test program. that in case the DMX signal is lost, interrupted, or power is lost, the operating mode chosen in this setup is the running 1. Press the MENU button until TEST is displayed, press ENTER. mode the fixture will revert to. You can also set this as the 2. The fixture will now run a self test. operating mode you would like the unit to return to when power is applied. 1. Press the MENU button until NODN is displayed, and either MASL, BLND, or LAST will be displayed beneath. 2. Press ENTER and the bottom choice will begin to flash. Use the UP or DOWN buttons to choose an operating mode you would like the unit to start up in when power is applied or the DMX signal is lost. HOLD - If the DMX signal is lost the fixture will stay in the last DMX setting. If power is applied and this mode is set, the unit will automatically go into the last DMX set up. PRGN (Master Slave) - If the DMX signal is lost or power is applied, the unit will automatically go into Master Slave mode and run a built-in show. BLAC (Blackout) - If the DMX signal is lost or interrupted, the unit will automatically go into stand by mode. 3. Press ENTER to confirm your desired set up. LED - With this function you can have the LED display turn off after 10 seconds. 1. Press the MENU button until LED is displayed, press ENTER. 2. The display will show either ON or OFF. Press the UP or DOWN buttons to select ON to keep the LED display on at all times, or OFF to switch to have the LED display switch off after 10 seconds. STRO - This will activate strobing. 1. Press the MENU button until STRO is displayed, press ENTER. 2. Use the UP or DOWN buttons to activate strobing or deactivate it. DISP - This function will reverse the display 180º. 1. Press the MENU button until DISP is displayed, press ENTER. 2. Press ENTER to flip the display. Press ENTER to flip it again. Press ENTER when you have made your desired setup. 3. Press ENTER to confirm. To make you LED display reappear again press any button. FHRS - With this function you can display the running time of the unit. 1. Press the MENU button until FHRS is displayed, press ENTER. 2. The running time of the fixture will now be displayed. Press MENU to exit. VER - Use this function to display the Software version of the unit. 1. Press the either the MENU button until VER is displayed, press ENTER. 2. The display will show the software version. RSET - This function will reset the unit. 1. Press the MENU button until RSET is displayed. Press the ENTER button and the unit will reset itself. ADJ Products, LLC Instruction Manual Page 12 ADJ Products, LLC Instruction Manual Page 13

8 Operating Instructions Universal DMX Control: This function allows you to use a universal DMX-512 controller to control the patterns, rotation and strobing. A DMX controller allows you to create unique programs tailored to your individual needs. 1. The has two DMX channel modes; a 2 channel mode and a 7 channel mode. See page 10 for detailed description of the DMX values and traits. 2. To control your fixture in DMX mode, follow the set-up procedures on pages 5-6 as well as the set-up specifications that are included with your DMX controller. 3. Follow the instructions on page 7 to set the DMX address. 4. For longer cable runs (more than a 100 feet) use a terminator on the last fixture. 5. For help operating in DMX mode consult the manual included with your DMX controller. Master-Slave Set Up Master-Slave Operation: This function will allow you to link up to 16 units together and operate without a controller. In a Master-Slave set-up one unit will act as the controlling unit and the others will react to the controlling units programs. Any unit can act as a Master or as a Slave. 1. Using standard XLR microphone cables, daisy chain your units together via the XLR connector on the rear of the units. Remember the Male XLR connector is the input and the Female XLR connector is the output. The first unit in the chain (master) will use the female XLR connector only - The last unit in the chain will use the male XLR connector only. For longer cable runs we suggest a terminator at the last fixture. 2. Set the Master to your desired operating mode. 3. Set the Slave unit(s) to address The slave unit(s) will now follow the Master unit. Sound Active Mode: This mode allows a single unit or several units linked together, to run to the beat of the music. 1. Press the MENU button until Soun is displayed, and press ENTER. 2. Press the UP or DOWN buttons to either activate sound active mode or deactivate, and press ENTER. The unit will now run to the beat of the music. 3. The sound sensitivity can be adjusted by turning the sound sensitivigy knob located on the back of the unit. Turning the knob clockwise is most sensitive and turn it counter-clockwise is least sensitive. Show Mode: This mode allows a single unit or several units linked together, to run to a built-in program. 1. Press the MENU button until Show is displayed, and press ENTER to activate. ADJ Products, LLC Instruction Manual Page 14 ADJ Products, LLC Instruction Manual Page 15

9 UC IR/Airstream App Control The UC IR (sold separately) infrared remote gives you control of various functions (See below). To control the fixture you must aim the remote at the front of the fixture and be no more than 30 feet away. The is also compatible with the Airstream IR app. The IR transmitter is available through any ADJ dealer or through the ADJ parts website. Plug the transmitter into the headphone jack of your ios phone or tablet. To control your IR fixture you must raise the volume to the maximum on your ios phone or tablet and aim the transmitter at the front of the fixture and be no more than 15 feet away. After you have purchased the Airstream IR transmitters, the app is a free download from the app store for your ios phone or tablet. The app comes with 3 pages of control depending on the IR fixture you are using. Please see below for IR functions including the corresponding app page. Works with App page 1. STAND BY - Pressing this button will blackout the fixture. Press the button again to return to the initial state. FULL ON - Hold this button down to fully light up the unit. When you let the button go, the unit will return to its previous state. STROBE - Press and hold this button for strobing. FADE/GOBO - This button is invalid for this fixture. DIMMER + and DIMMER - - These buttons are invalid for this fixture. COLOR - Press this button to select a color. Use buttons 1-9 to find your desired color Use buttons 1-9 to select your desired color when color mode is active. Use buttons 0-2 to select your desired show when in show mode. SOUND ON & OFF - Use the buttons to activate and deactivate sound active mode. SHOW 0 - Press this button to activate show mode and press this button again to activate random show (Show 0). Use buttons 1 & 2 to to run either show 1 or show 2. 2 Channel DMX Mode Channel Value Function 1 SHOW MODE 0-9 NO FUNCTION SHOW 0 (LED, LASER, & STROBE) SHOW 1 (LED) SHOW 2 (LASER) 2 SHOW SPEED/SOUND SENSITIVITY SHOW SPEED SLOW - FAST SOUND ACTIVE 198mm/7.80 ADJ Products, LLC Instruction Manual Page 16 ADJ Products, LLC Instruction Manual Page mm/8 147mm/5.78 CAD Drawing 218mm/8.58

10 7 Channel DMX Mode Channel Value Function 1 SHOW MODE 0-9 NO FUNCTION SHOW 0 (LED, LASER, & STROBE) SHOW 1 (LED) SHOW 2 (LASER) 2 RGBW COLOR MACRO 0-9 NO FUNCTION COLOR COMBINATIONS COLOR FADE (1 COLOR) SLOW-FAST COLOR FADE (MIXED) SLOW - FAST 3 LED STROBE 0-9 STROBE OFF STROBING SLOW - FAST SOUND ACTIVE STROBE 4 LASER COLOR CONTROL 0-9 LASER OFF RED GREEN RED & GREEN RED ON, GREEN FLASH GREEN ON, RED FLASH RED & GREEN FLASH RED & GREEN ALTERNATE FLASH 5 LASER STROBING STROBING SLOW - FAST SOUND ACTIVE STROBE 6 LED MOTOR CONTROL SELECT MOTOR POSITION ROTATION SLOW - FAST 7 LASER MOTOR CONTROL LASER PATTERNS PATTERN CHASE SLOW - FAST Fuse Replacement Disconnect the unit from its power source. Remove the power cord from the unit. Once the cord has been removed, you will find that the fuse holder is located inside the power socket. Insert a flat-head screw driver into the power socket and gently pry out the fuse holder. Remove the bad fuse and replace with a new one. The fuse holder also has a holder for a spare fuse. Trouble Shooting Trouble Shooting: Listed below are a few common problems that you may encounter, with solutions. No light output from the unit; 1. Be sure the fuse has not blown. The fuse is located on the rear panel. Unit does not respond to sound; 1. Low frequencies (bass) should cause the unit to react to sound. Tapping on the microphone, quiet or high pitched sounds may not activate the unit. Cleaning Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light output. 1. Use normal glass cleaner and a soft cloth to wipe down the outside casing. 2. Use a brush to wipe down the fan grill. 3. Clean the external optics with glass cleaner and a soft cloth every 20 days. 4. Clean the internal optics with glass cleaner and a soft cloth every days. 5. Always be sure to dry all parts completely before plugging the unit back in. Cleaning frequency depends on the environment in which the fixture operates (I.e. smoke, fog residue, dust, dew). In heavy club use we recommend cleaning on a monthly basis. Periodic cleaning will ensure longevity, and crisp output. ADJ Products, LLC Instruction Manual Page 18 ADJ Products, LLC Instruction Manual Page 19

11 Warranty MANUFACTURER S LIMITED WARRANTY A. Eliminator Lighting hereby warrants, to the original purchaser, Eliminator Lighting products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought. B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the product please contact Eliminator Lighting Service Department at Send the product only to the Eliminator Lighting factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, Eliminator Lighting will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in it s original package. No accessories should be shipped with the product. If any accessories are shipped with the product, Eliminator Lighting shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof. C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which Eliminator Lighting concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the Eliminator Lighting factory unless prior written authorization was issued to purchaser by Eliminator Lighting; if the product is damaged because not properly maintained as set forth in the instruction manual. D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check up. During the period specified above, Eliminator Lighting will replace defective parts at its expense with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of Eliminator Lighting under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of Eliminator Lighting. All products covered by this warranty were manufactured after August 15, 2012, and bear indentifying marks to that effect. E. Eliminator Lighting reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by Eliminator Lighting in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumer s and/or Dealer s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall Eliminator Lighting be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product. This warranty is the only written warranty applicable to Eliminator Lighting Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published. MANUFACTURER S LIMITED WARRANTY PERIODS: Lighting Products = 1-year (365 days) Limited Warranty (Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding LED and lamps) Laser Products = 1 Year (365 Days) Limited Warranty (excluding laser diodes which have a 6 month limited warranty) L.E.D. Products = 2-year (730 days) Limited Warranty (excluding motors, PCB boards, and power supplies, which have a 1-year (365 day Limited Warranty) batteries which have a 180 day limited warranty). Only the L.E.D.s carry a 2-year warranty (excluding StarTec Series which a carries a 1 Year Limited Warranty) Note: 2 Year Warranty only applies to purchases within the United States. ADJ DMX Controllers = 2 Year (730 Days) Limited Warranty (excluding faders and tact switches) Notes ADJ Products, LLC Instruction Manual Page 20 ADJ Products, LLC Instruction Manual Page 21

12 Technical Specifications: Model: LEDs: Laser: Voltage: Power Consumption: Beam Angle: Dimensions: Weight: DMX Channels: Fuse: Duty Cycle: Warranty: Specifications 2 x 10W RGBW LEDs 30mW Green Laser 100mW Red Laser 100~240v 50Hz~60Hz 33W 120 Degrees 8 (L) x 7.75 (W) x 8.5 (H) 205 x 198 x 218mm (W/ Bracket) 8 (L) x 7.75 (W) x x 198 x 147mm (w/o Bracket) 4 Lbs./1.7 Kgs. 2 DMX Channel Modes: 2 Channel & 7 Channel Mode 2 Amp None 1 Year (365 Days) Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice. Auto Sensing Voltage: This fixture contains a automatic voltage switch, which will auto sense the voltage when it is plugged into the power source. ADJ Products, LLC Instruction Manual Page 22 ADJ Products, LLC 6122 S. Eastern Ave. Los Angeles, CA USA Tel: / Fax: Web: / info@americandj.com A.D.J. Supply Europe B.V. Junostraat EW Kerkrade The Netherlands service@adjgroup.eu / Tel: / Fax: