Synergy Controller Application Note 74 February 2011, Revision P4 Tidal Engineering Corporation Synergy Controller LED Backlight Retrofit
|
|
- Bertina Harriet Reed
- 6 years ago
- Views:
Transcription
1 Synergy Controller LED Backlight Retrofit Since their introduction in 2000, Synergy Controller and VersaTenn V 5.7 Liquid Crystal Displays (LCDs) utilize a CCFL (Cold Cathode Fluorescent Lamp) backlight. A Synergy LED Backlight Retrofit kit is now available that offers a lifetime guarantee. This kit, P/N TE2136, utilizes Hi Brightness (HB) white LEDs from CREE and is backward compatible with all current Synergy Controller and VersaTenn V configurations equipped with 5.7 LCDs. This application note details the installation of this LED Backlight kit. The Synergy LED Backlight kit ships in a protective shipping tube as shown below. To begin the installation, pull the cover off one end of the shipping tube and pull out the Application Note 74 and antistatic bag containing the kit contents. Page 1 of 14
2 The TE2136 kit contains one of each of the following items: (Identified in the figure above) 1. TE2113, Synergy Micro LED Backlight Lamp Assembly 2. TE2137, Synergy Micro LED Backlight Power Cable Assembly 3. TE2121, Synergy Micro LED Backlight Driver Assembly 4. S2B XH A, J17, Connector, 2 POS, Right/Angle Connector 5. Teflon Sleeving, 9 inches,.(040" ID, CLR OD, P/N TFT20018 NA005 ). 6. Tyrap Cable Ty (Panduit Corp, P/N PLC2S S6 C0, CLAMP TIE STD #6SCR WR BK 7.9"). 7. Synergy_Controller_App_Note_74_Synergy_LED_Backlight_Retrofit_P4 (this document) Page 2 of 14
3 The installation steps are summarized as follows: 1. Remove controller from the system. See technical manual for detailed instructions. 2. Remove LCD from controller as described below. 3. Remove the CCFL Lamp and install the LED Backlight. For Sharp Displays (Appendix A) For other Styles (Appendix B). 4. Connect the TE2137 Power Cable Assembly to the TE2121 Driver and the 5 VDC Plug. If necessary, solder the supplied S2B XH A connector in place. 5. Re assemble system. Page 3 of 14
4 For VersaTenn V Controllers Once the controller is removed from the chamber remove the four screws securing the LCD Display to the controller. Remove the six screws, top and bottom, and flip the touch sensor frame to the left as shown below. Remove the four screws holding the LCD to the LCD panel. Remove the CCFL Lamp Assembly from the display and install the LED Lamp Assembly per Appendix A (for the Sharp Display) and Appendix B (for the FEMA display) as required. Page 4 of 14
5 Remove the four screws and lift the panel to access the CCFL inverter as shown below: Flip the panel down and unplug the 5 VDC power from the touch controller and the lamp from the CCFL lamp inverter. Then remove the screw holding the CCFL inverter to the panel as shown below: Lamp Power 5 VDC Power Touch Controller CCFL lamp inverter Secure the Ty Rap around the LED Driver and cut the excess portion as shown below: Page 5 of 14
6 Push the Lamp Power Cable thru the grommet and connect to the LED Driver as shown below: Secure the new (a) TE2121 LED Driver to the panel with the screw and plug the (b) TE2137 TE2137 power cable into the (c) 5 VDC plug on the (d) Touch Controller. Then connect the (e) Lamp Power cable to the LED Driver as shown below (d) Touch Controller (e) Lamp Power (a) LED Driver 5 VDC Power (b) TE2137 Lamp Driver Power Cable Page 6 of 14
7 For Synergy Micro, Micro II, and Micro V Models: Remove the controller from the chamber and remove the LCD Display hardware as follows. Unplug the ribbon cable and the three discrete wires from the controller as shown below. Remove the (10) screws and lift the LCD panel out of the case. Remove the (5) screws securing the touch screen support and unplug the flex cable for the touch sensor as shown below. Page 7 of 14
8 Remove the touch screen panel and the touch screen support as shown below. Remove the (4) Screws securing the LCD to the panel and the touch screen support as shown below. Remove the CCFL Lamp and install the LED Kit per Appendix A (for the Sharp Display) and Appendix B (for the FEMA display) as required. Connect the TE2137 LED Driver power cable and the TE2113 LED Lamp cable to the TE2121 LED Driver as shown in the figures below. J17 Note that the J17 site is not populated on all controllers and therefore the S2B XH A Connector is provided so it can be solder to the board. Page 8 of 14
9 Appendix A LED Lamp Installation in Sharp LM057 Display Push the lamp catch to the side and pull the lamp housing from the display using the cable as shown below. Cut the Teflon sleeving in half (4.5 ) as shown below. Place the sleeving in the lamp housing then place the TE2113 LED lamp in the display lamp housing on top of the sleeving as shown below. Cable Cable exits opposite this end Slide the lamp housing into the Display as shown below. Page 9 of 14
10 Secure the cable in the cable support as shown below. Page 10 of 14
11 Appendix B LED Lamp Installation in FEMA Display Remove the (5) screws on the back of the display and bend back the retaining tabs on the ends of the display as shown below Lift the back cover as shown below: Lift the lamp housing and remove it from the display and pull the white lead from the lamp housing as shown below. Page 11 of 14
12 Gently lift the lamp out of the housing, fold the Teflon sleeving in half and place it in the lamp housing as shown below. Note that the sleeving is not cut in half for the FEMA but is for the Sharp CAUTION: THE LAMP IS MADE OF GLASS AND IS VERY FRAGILE. BE CAREFULL. Seat the Teflon sleeving in the lamp housing then place the TE2113 LED Lamp assembly in the lamp housing as shown below: Note that the cable should exit the housing away from the end shown. Cable exits opposite this end Cable Place the lamp housing in the slot on the back of the display as shown below: Page 12 of 14
13 Place the back cover on the display and then replace the (5) screws on the back of the display as shown below. Bend the retaining tabs on the ends of the display back into position. Page 13 of 14
14 About Tidal Engineering Headquartered in Randolph, NJ, Tidal Engineering Corporation has been designing and building award winning embedded hardware and software for test and measurement and data acquisition applications since The company is recognized for technical expertise in such areas as Embedded IEEE 488, and turnkey SCADA (Supervisory Control and Data Acquisition) systems. Tidal s products are available exclusively through ADI American Distributors Inc., an ISO 9002 certified distributor of electronic and electromechanical components and assemblies. Tidal Engineering Corporation 2 Emery Avenue Randolph, NJ Tel: 973/ Fax: 973/ info@tidaleng.com Page 14 of 14
Replacing the PanelMate epro PS, PanelMate epro PS EE, and PanelMate epro PS OD 7685x-12 Series Backlight Assembly
Replacing the PanelMate epro PS, PanelMate epro PS EE, and PanelMate epro PS OD 7685x-12 Series Backlight Assembly Introduction The Backlight Replacement Kit provides a replacement backlight for the PanelMate
More informationNewScope-7A Operating Manual
2016 SIMMCONN Labs, LLC All rights reserved NewScope-7A Operating Manual Preliminary May 13, 2017 NewScope-7A Operating Manual 1 Introduction... 3 1.1 Kit compatibility... 3 2 Initial Inspection... 3 3
More informationimac Intel 20" EMC 2133 and 2210 LCD Backlights (CCFL) Replacement
imac Intel 20" EMC 2133 and 2210 LCD Backlights (CCFL) Replacement The CCFL back lights are replaceable. I have pulled mine apart and documented my method. '''NOTE''' This is not for the feint hearted!
More informationReplacing the PanelMate epro PS, PanelMate epro PS Classic, PanelMate epro PS EE, and PanelMate epro PS OD 7685x-15xx Series Backlight Assembly
Introduction Replacing the PanelMate epro PS, PanelMate epro PS Classic, PanelMate epro PS EE, and PanelMate epro PS OD 7685x-15xx Series Assembly Instruction Leaflet IL04802009E Effective September 2008
More informationHD Flex Patch Panel. ASSEMBLY VIEW (FLEX1UPN** shown) FS128B. CONTENTS: (#) indicates FLEX4UPN** quantity
HD Flex Patch Panel Part Numbers: FLEX1UPN**, FLEX2UPN**, FLEX4UPN** Panduit Corp. 2018 INSTALLATION INSTRUCTIONS Note: HD Flex Patch Panels are compatible with HD Flex Fiber System Components. HD Flex
More informationiphone 7 Plus LCD Screen and Digitizer Replacement
iphone 7 Plus LCD Screen and Digitizer Replacement Replace just the bare front panel not including the home/touch ID sensor, front-facing camera and sensor cable, or earpiece speaker in an iphone 7 Plus.
More informationOAI-80018AA-7602-B 5/22/2007. Optrex Part Numbering System Description
OAI-80018AA-7602-B 5/22/2007 Optrex Part Numbering System Description TYPES OF DISPLAYS PASSIVE CHARACTER & GRAPHICS MODULE ACTIVE TFT MODULE OAI-80018AA-7602-B Slide 2 of 7 BACK TO INDEX CHARACTER & GRAPHIC
More informationFOSC-600 C and D I N S T A L L A T I O N I N S T R U C T I O N
FOSC-600 C and D I N S T A L L A T I O N I N S T R U C T I O N In-line and butt version Cold applied re-usable fiber optic closure Contents 1 Introduction 1.1 Product description 1.2 Capacity 2 General
More informationRMS 8424S Quick Start
VIEWSIZE THE WORLD RMS 8424S Quick Start Standard 4 unit rack mount size 8 inch LCD 2 1024 3 (RGB) 600 16:9 / 4:3 adjustable SDI/HDMI embedded audio output via 3.5mm earphone socket Support SDI/DVI audio
More information3M Cold Shrink Splice Kit QS-III 5515A
3M Cold Shrink Splice Kit QS-III 5515A for UniShield, Wire Shielded, Longitudinally Corrugated (LC), and Tape Shielded (Ribbon Shielded) Cable or Transitions to Concentric Neutral (CN)/Jacketed Concentric
More informationMAGNETIC CARD READER DESIGN KIT TECHNICAL SPECIFICATION
MAGNETIC CARD READER DESIGN KIT TECHNICAL SPECIFICATION Part Number: D99821002 Rev 212 MAY 2017 REGISTERED TO ISO 9001:2008 1710 Apollo Court Seal Beach, CA 90740 Phone: (562) 546-6400 FAX: (562) 546-6301
More informationWater blocking tape. Locator ridge HPA-0486
Table of Contents STANDARD RECOMMENDED PROCEDURE 004-138 ISSUE 1 MARCH 2012 PAGE 1 OF 12 Sheath Removal and Mid-Span Access of Dielectric ALTOS Cable with FastAccess Technology p/n 004-138, Issue 1 1.
More informationTechnical Information Bulletin
June 4, 2001 #TIB0003 Units Affected: Model Serial Numbers Model Serial Numbers SVT-2PRO T2PDxxxxxxxxx SVTAV AXVDxxxxxxxxx ATLDxxxxxxxxx BJIDMAxxxxxxx SVT-2PROJ T2PJxxxxxxxxx SVTAVJ BAHJxxxxxxxxx ATLJxxxxxxxxx
More information3M Cold Shrink Splice Kit QS-III 5514A
3M Cold Shrink Splice Kit QS-III 5514A for UniShield, Wire Shielded, Longitudinally Corrugated (LC), and Tape Shielded (Ribbon Shielded) Cable or Transitions to Concentric Neutral (CN)/Jacketed Concentric
More informationOperating Instructions for Throttle Valves Using VRC Valve Positioner
ThrottleMaster TM Operating Instructions for Throttle Valves Using VRC Valve Positioner p/n: X709116 $10.00 3/2012 Throttlemaster is a registered trademark of Vacuum Research Corporation Introduction The
More informationApplication Note [AN-007] LCD Backlighting Technologies and Configurations
Application Note [AN-007] LCD Backlighting Technologies Introduction Liquid Crystal Displays (LCDs) are not emissive i.e. they do not generate their own light. Transmissive and transflective displays require
More informationBusiness Display Solutions - Institutional Television Mirror TV. Installation Guide for 32PM8822 ( BDL3221M) 42PM8822 (BDL4221M)
Business Display Solutions - Institutional Television P.O. Box 218, 5600 MD Eindhoven, The Netherlands 32-42 Mirror TV Installation Guide for 32PM8822 ( BDL3221M) 42PM8822 (BDL4221M) Date: October 2005
More informationSLiC Fiber Aerial Closure System
3 SLiC Fiber Aerial Closure System SLFC 533-SP SLFC 533-TS SLFC 733-SP Instructions May 2005 78-8135-4502-3-B N C H E S R A N G E M IL L IM E T E R S.4 10.6.8 A B C 15 20 I 1.0 Kit Contents Note: Examine
More informationProduct General Specification
. General Description The is a Color Active Matrix with an integral Cold Cathode Fluorescent Tube(CCFT) back light system. The matrix employs asi Thin Film Transistor as the active element. It is a transmissive
More informationAll-In-One. Connector System PODIUMS AUDITORIUMS FLY PACKS MOBILE - TRUCKS PANELS CORPORATE FLOOR POCKETS RENTAL & STAGING RACKS
DATA 2 CONTROL 1 A 5 B 6 C 7 8 9 G 13 J 15 L 19 P All-In-One E 10 16 M 20 R Connector System F 11 12 H K 17 14 18 N 21 22 T 26 PODIUMS AUDITORIUMS FLY PACKS VIDEO 4 AUDIO 3 D MOBILE - TRUCKS PANELS CORPORATE
More informationC-net WIND. User s Guide
C-net WIND User s Guide EMC Directive 89/336/EEC This product has been designed to be compliant with the above EMC Directive. Maximum performance and compliance with the EMC Directive can only be ensured
More information3M Cold Shrink QS-III Silicone Rubber Splice Kit 5488A-TOW/WOT
3M Cold Shrink QS-III Silicone Rubber Splice Kit 5488A-TOW/WOT For Tape Over Wire (TOW) and Wire-Over-Tape (WOT) Shielded Cable For 250 2000 kcmil cable with 650-mil primary insulation thickness Instructions
More informationCN Remove the scanner assembly (X476 and X576 models) and all doors/covers.
CN598-67045 www.hp.com/support IMPORTANT: Ensure the product firmware is upgraded to at least version 1336MR before performing this repair procedure. If the firmware upgrade cannot be completed, contact
More informationInstalling a Wire Mesh Pulling Grip on All-Dielectric DX Armored Fiber Optic Cables
revision history Issue Date Reason for Change Related literature SRP-004-136 Accessing All-Dielectric DX Armored Fiber Optic Cables Admonishments 1. General This procedure provides instructions for installing
More information3. Electronics and MMU2 unit assembly
Written By: Jakub Dolezal 2018 manual.prusa3d.com/ Page 1 of 34 Step 1 Tools necessary for this chapter Please prepare tools for this chapter: 2.5mm Allen key for M3 screws 2mm Allen key for nut alignment
More informationSCdefault. 900 Installation instructions. Accessories Part No. Group Date Instruction Part No. Replaces :36-29 Sep
SCdefault 900 Installation instructions SITdefault Upgrade to Premium 300 sound system MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group
More informationMedium Box for Cable Termination
FIST-MB2-T I N S T A L L A T I O N I N S T R U C T I O N Medium Box for Cable Termination Contents 1 Introduction 1.1 Product description. 2 General 2.1 Tools 2.2 Kit contents 3 Installation and pre assembling
More informationAinsworth Part # volt CUT TO FIT LED bar to replace cold cathode lamps in all LCD s from 10 to 22
Ainsworth Part #2840-12 volt CUT TO FIT LED bar to replace cold cathode lamps in all LCD s from 10 to 22 Part #5030 24 volt LED flexible strip to replace cold cathode lamp in belly glass Aristocrat Part
More informationPMCL300 Series TFT LCD Monitor 17-INCH, 19-INCH, OR 19-INCH WIDE, WITH MULTIMODE FUNCTIONALITY
PRODUCT SPECIFICATION viewing solutions PMCL300 Series TFT LCD Monitor 17-INCH, 19-INCH, OR 19-INCH WIDE, WITH MULTIMODE FUNCTIONALITY Product Features Space-Saving, Flat Panel Design Picture-Frame-Style
More information3M Cold Shrink Splice Kit QS-III 5416A
3M Cold Shrink Splice Kit QS-III 5416A for Jacketed Concentric Neutral (JCN) and Concentric Neutral Cable Instructions IEEE Std. 404 15 kv Class 150 kv BIL CAUTION Working around energized systems may
More informationGeneral Description. SC Configurations
S onnectors General Description Delta S series connectors are medium-size, 50Ω impedance connectors with 11 16-24 threaded coupling and good power handling capability, particularly those connectors noted
More informationMagelis XBT ZG43 Backlight Replacement Kit Quick Reference Guide
Magelis XBT ZG43 Backlight Replacement Kit Quick Reference Guide Thank you for purchasing the XBT ZG43 replacement backlight. Be sure to read the following Backlight Replacement Instruction bulletin prior
More informationACUBRITE 23 SS. Manual. Stainless Steel Chassis 23" LCD Display. Content
ACUBRITE 23 SS Stainless Steel Chassis 23" LCD Display Manual Introduction... 2 Hardware Installation... 2 The Display Timing... 5 The Display Outline Dimensions... 6 The Display Controls... 7 The Screen
More informationHCS - HES Cabling Systems
HCS - HES Cabling Systems Installation Manual for HCS High-Capacity Fiber-Optic Rack-Mount Cabinets Be sure to read and completely understand this procedure before applying product. Be sure to select the
More informationWinmate Communication INC.
20.1 Military Grade Display Model: R20L100-RKA2ML User s Manual Winmate Communication INC. May, 2011 1 IMPORTANT SAFETY INSTRUCTIONS Please read these instructions carefully before using the product and
More informationDL-AR2 Technical Specifications Universal HDMI Adapter Ring Rev
DL-AR2 Technical Specifications Universal HDMI Adapter Ring Rev. 130814 The DL-AR2 Digital Adapter Keychain was developed to support the rising proliferation of mobile devices used in presentation systems.
More informationINSTALLATION MANUAL FOR THE TIMING LIGHT
INSTALLATION MANUAL FOR THE TIMING LIGHT May 12 2014 SPORTS SPLIT STEP 12566 LAZY ACRES CRT NEVADA CITY, CA 95959 www.sports-split-step.com vicborg70@gmail.com 530-272-7345 1 1. The installation of the
More informationInstructions. Cable with Armor F CAUTION. October Rev A
3M Single Conductor Accessory Breakout Kits (BOK's) for use with 3M Cable Accessories (Terminations, T-Bodies and Push-On Elbows) For Use With Single Conductor Accessories On Three-Core Conductor Cables
More informationPanduit Recommended Best Case Practice Split Fibre
Panduit Recommended Best Case Practice Split Fibre Panduit Corp. 2009 BEST PRACTICES PN526 Table of Contents 1.0 Enclosure Prep... 2 2.0 Fibre Cable Prep and Installation... 2 3.0 Pigtail Installation...
More informationCold Shrink Three-Conductor Splice Kit QS-III for use on Armor and Non-Armor Cables Instructions IEEE Std kv Class 250 kv BIL
Cold Shrink Three-Conductor Splice Kit QS-III for use on Armor and Non-Armor Cables Instructions IEEE Std. 404 35 kv Class 250 kv BIL Kit Number 5798A-MT Cable Range Requirements Cable Insulation O.D.
More information1. General Description
LP2X05 Product Specification. General Description The LP2X05 is a Color Active Matrix with an integral Cold Cathode Fluorescent Lamp(CCFL) backlight system. The matrix employs asi Thin Film Transistor
More informationOptical Distribution Box 300 Installation Guide. Version : R0.0
Optical Distribution Box 300 Installation Guide Document No. : OD16-546-L-01 Version : R0.0 Date: 21-Mar-2018 IMPORTANT INSTRUCTIONS When using fiber optic equipment, basic precautions should always be
More informationPLL1920M LED LCD Monitor
PLL1920M LED LCD Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Safety Precautions...2 First Setup...3 Front View of the Product...4 Rear View of the Product...5 Installation...6
More information(E-UB) UPRIGHT BIKE INSTALLATION INSTRUCTIONS
(E-UB) UPRIGHT BIKE INSTALLATION INSTRUCTIONS E-UB Upright Bike 4 620-7922 Rev B GENERAL Before using this product, it is essential to read ALL installation Instructions and this ENTIRE operations manual;
More informationTFT-150R-G. Tape Shield Cable (page 2) Suggested Installation Equipment (not supplied with kit) Wire Shield Cable (page 7)
TFT-150R-G 5-15kV Cold Applied Indoor (5-8kV Indoor and Outdoor) Termination for Copper Tape, Wire Shield, Lead Sheath, and UniShield Cable Suggested Installation Equipment (not supplied with kit) Cable
More informationIPad 3 (glass) REPAIR GUIDE. Version Edition
IPad 3 (glass) REPAIR GUIDE Version 1 2016 Edition IPad 4 REPAIR GUIDE LCD AND DIGITIZER REPLACEMENT RiAna Soto Repair Training Specialist rsoto@cellairis.com FOR EVERY REPAIR MAKE SURE TO COMPLETE, INITIAL,
More informationipad Air 2 Wi-Fi Display Assembly Replacement
ipad Air 2 Wi-Fi Display Assembly Replacement Fix a cracked or faulty screen by replacing the display assembly in an ipad Air 2 Wi-Fi. Written By: Evan Noronha ifixit CC BY-NC-SA www.ifixit.com Page 1
More informationTotal Chlorine Sensor
LIQ_MAN_ABR_ April 2014 Total Chlorine Sensor For additional information, please visit our website at www.rosemountanalytical.com. CAUTION The wetted sensor materials may not be compatible with process
More information3 Closure preparation 3.1 Work-stand 3.2. Opening FIST-GCOG2-Dx Preparing drop cable with micro-tubes
FIST-GCOG2-Dx24 I N S T A L L A T I O N I N S T R U C T I O N FTTH closure for micro-tubes and micro-cables Content 1 Introduction 2 Kit content 3 Closure preparation 3.1 Work-stand 3.2. Opening FIST-GCOG2-Dx24
More informationDisplays Open Frame Monitor Model Number: AND-TFT-150Bxx
Displays 15.0 Open Frame Monitor Model Number: AND-TFT-150Bxx The AND-TFT-150Bxx 15.0 Open Frame Monitor series are rugged, high performance Industrial LCD Monitors, designed for commercial and industrial
More informationSV-LCD50. Installation and User Guide. Thin-Film Transistor (TFT) Liquid Crystal Display (LCD) Color Rear Vision Monitor. Version 1.
SV-LCD50 Installation and User Guide Thin-Film Transistor (TFT) Liquid Crystal Display (LCD) Color Rear Vision Monitor Version 1.00 August 2004 SV-LCD50 Installation and User Guide TFT LCD Color Rear Vision
More informationBacklight Replacement
Installation Instructions Backlight Replacement Catalog Numbers 2711P-RL7C, 2711P-RL7C2, 2711P-RL10C, 2711P-RL10C2, 2711P-RL12C, 2711P-RL12C2, 2711P-RL15C Topic Page About This Publication 1 Important
More informationTMX-R1000 (USA and JAPAN) TMX-R1000P (EUROPE)
ALPINE ELECTRONICS, INC. TMX-R1000 (USA and JAPAN) TMX-R1000P (EUROPE) VGA MOBILE CINEMA MONITOR OWNER S MANUAL Features 10.2 inch Wide VGA TFT Active Matrix Color LCD (800 x 480) 3 AUX In / 1 AUX Out
More informationDIY. How to install a PL-259 connector. Parts list: Tools list: Worthwhile projects you can build on your own
DIY Worthwhile projects you can build on your own Just like you, I often need to install a PL-259 connector on a length of coax (coaxial cable), to attach it to the mating SO-239 connector of a mobile
More informationDLMP-45/45R Installation Instructions
DLMP-45/45R Installation Instructions Tools Needed Posidrive No.3 Screwdriver Large Flat Head Screwdriver 2x 10mm Spanner 1x 13mm Spanner Ø8mm Drill Ø6mm Drill Kit Contents [ ] 1x Tube 2.5M long 17420
More informationFIST-MB2-S. FIST Medium Box for Cable Splicing Only. 4 Cable installation. 1 Introduction. Contents. 2 General. 5. Fiber routing to individual trays
FIST-MB2-S I N S T A L L A T I O N I N S T R U C T I O N FIST Medium Box for Cable Splicing Only Contents 1 Introduction 1.1 Product description 2 General 2.1 Tools 2.2 Kit contents 3 Installation and
More informationIP-LINX. Installation Guide
Installation Guide Installation Guide, 146653-4 Copyright 2017, Telect, Inc. All Rights Reserved Telect and Connecting the Future are registered trademarks of Telect, Inc. 22425 East Appleway Ave. # 11
More informationIndustrial Monitor Update Kit
Industrial Monitor Update Kit (Bulletin Number 6157) Installation Instructions 2 Table of Contents Table of Contents Industrial Monitor Update Kit... 3 Overview... 3 Part 1 - Initial Preparation... 5 Part
More informationQuickSpecs. HP V19b 18.5-inch Monitor. Overview. 1. Menu 3. Plus ( + ) 5. Power 2. Minus ( - ) 4. OK. 1. Power connector 3. Security lock slot 2.
Overview 1. Menu 3. Plus ( + ) 5. Power 2. Minus ( - ) 4. OK 1. Power connector 3. Security lock slot 2. VGA Brazil Version 1 April 20, 2018 Page 1 Model: 2XM32AA Panel Type 18.5-inch TN Viewable Image
More informationGeneral. zoom ring. focus ring. Size of liquid. Color. foot adjust levers. Projection. Computer In. Mouse/Com. Power
Projector Specifications status lights control panel speakers zoom ring focus ring General Type of display Size of liquid crystal panels Poly-silicon Thin Film Transistor (TFT), active matrix Diagonal:
More informationBuilding a MidiBox LCD Cable
Building a MidiBox LCD Cable By Jim Henry, 3-Apr-2004 An LCD panel may be connected to the Core module by a 16 conductor flat ribbon cable. A 16 pin insulation displacement connector (IDC) terminates one
More informationProdigy Eclipse ECC and EH222 Service Parts EH222 Cabinet - C Series
This part list contains the service parts for the Eclipse ECC 800 and 000 systems. Prodigy Plus D Series production began in late 0. The models that are covered include: EH - head ECC0800 - condensing
More informationVOH681/VOH681P. ion Manual
VOH681/VOH681P Operat ation ion Manual Important Notice It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped with a television viewer or screen that is located in
More information3M Coupling Tray FDTC-10S-COUPLINGTRAY
3M Coupling Tray FDTC-10S-COUPLINGTRAY for use with 3M Fiber Dome Closures FDC 10S Instructions July 2010 3 1.0 Introduction The 3M Coupling Tray FDTC-10S-COUPLINGTRAY can accommodate up to 10 loose tubes.
More informationIP-LINX Fiber :: X-XXXX
Fiber :: 055-797X-XXXX User Manual Telect, Inc. All rights reserved. 146653-A0 Table of Contents Chapter 1: Introduction...3 1.1 Tools Required...3 1.2 Additional Parts...3 1.3 Assemblies...3 Chapter 2:
More informationSplice Closure Fiber (SCF) Family
features and benefits Sealed butt-style closure Aerial, wall, pole, direct buried Ribbon reel-end to reel-end splicing Split end caps Modular fiber management system standards Telcordia GR-771 tested RDUP
More informationP XGA TFT Monitor. User s Manual
P6151 15 XGA TFT Monitor User s Manual Disclaimers This manual has been carefully checked and believed to contain accurate information. Axiomtek Co., Ltd. assumes no responsibility for any infringements
More informationOWNER S MANUAL MOTORIZED 7 WIDE TFT LCD COLOR MONITOR CNT-701
OWNER S MANUAL PW MOTORIZED 7 WIDE TFT LCD COLOR MONITOR CNT-701 ANY CHANGES OR MODIFICATIONS IN CONSTRUCTION OF THIS UNIT DEVICE WHICH IS NOT APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIACE COULD VOID
More informationLA1500R USER S GUIDE.
LA1500R USER S GUIDE www.planar.com The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright. All rights
More information3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN-4/0-500
3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN-4/0-500 for Jacketed Concentric Neutral (JCN) and Flat Strap Neutral Cable Instructions IEEE Std. 404 15 kv Class 150 kv BIL CAUTION Working around energized
More information3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN
3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN-500-1000 for Jacketed Concentric Neutral (JCN) and Flat Strap Neutral Cable Instructions IEEE Std. 404 15 kv Class 150 kv BIL F CAUTION Working around
More informationUNSIGNED HARDCOPY NOT CONTROLLED
SUBJECT: APPROVED BY STATUS PURPOSE AFFECTED FUNCTIONS REFERENCES Cable and Harness Making Manager, Hardware Engineering Maintenance Revision Establishes requirements for the fabrication and inspection
More information24-Fiber LANLINXS (Model # ) 48-Fiber LANLINXS (Model # ) User Manual
24-Fiber LANLINXS (Model # 055-8632-5000) 48-Fiber LANLINXS (Model # 055-8832-5000) User Manual 24-Fiber LANLINXS (Model # 055-8632-5000) 48-Fiber LANLINXS (Model # 055-8832-5000) User Manual, Part Number
More informationOperating Instructions
Marshall Electronics Broadcast A/V Division Model No. V-LCD70W-SH 7 3G-SDI / HDMI Professional Camera-Top Monitor Operating Instructions Ver. 1.0 V-LCD70W-SH Operation Manual Table of Contents 1. Installation
More informationIPad 4 REPAIR GUIDE. Version Edition
IPad 4 REPAIR GUIDE Version 1 2016 Edition IPad 4 REPAIR GUIDE LCD AND DIGITIZER REPLACEMENT RiAna Soto Repair Training Specialist rsoto@cellairis.com FOR EVERY REPAIR MAKE SURE TO COMPLETE, INITIAL, AND
More informationHDS-42AVR HDMI Switcher INSTALLATION MANUAL
HDS-42AVR HDMI Switcher INSTALLATION MANUAL -42AVR-Manual.indd 1 Table Of Contents Introduction...3 Safety Information...4 Kit Contents...4 Feature Set...4 HDS-42AVR Remote Control/Operation...5 Specifications...6
More information3M Motor Lead Inline Splice 5331, 5332, 5333 & 5334
3M Motor Lead Inline Splice 5331, 5332, 5333 & 5334 for 5/8 kv Non-Shielded and Shielded Cables (Ribbon, Wire and UniShield Cables) Instructions Cable Size Range: Feeder: #8 AWG 500 kcmil Motor Lead: #10
More information6.4 Chassis Monitor Model Number: LCM0642xx. SPEC No.: SAS Version: 0.0 Issue Date: April 16, Introduction:
6.4 Chassis Monitor Model Number: LCM0642xx This product is RoHS compliant SPEC No.: SAS-0908003 Version: 0.0 Issue Date: April 16, 2010 1. Introduction: 1.1 About the Product The LCM0642xx 6.4 Chassis
More informationWCH Slack Storage Housing (WCH-SSH-2 & WCH-SSH-4-12)
Corning Cable Systems SRP-003-448 Issue 3, October 2000 Page 1 of 6 WCH Slack Storage Housing (WCH-SSH-2 & WCH-SSH-4-12) Figure 1 Table of Contents 1. General... 1 2. Description... 1 3. Tools and Materials...
More informationLGX Compatible (LSX) Connector Module) User Manual)
LGX Compatible (LSX) Connector Module) User Manual) 15948-A LSX Connector Module (72-Position Module Shown) Content Page 1 DESCRIPTION... 3 2 DIMENSIONS AND SPECIFICATIONS... 5 3 INSTALLATION... 6 3.1
More informationipad Air 2 Wi-Fi Display Assembly Replacement
ipad Air 2 Wi-Fi Display Assembly Replacement Fix a cracked or faulty screen by replacing the display assembly in an ipad Air 2 Wi-Fi. Geschreven door: Evan Noronha ifixit CC BY-NC-SA nl.ifixit.com Pagina
More informationINSTALLATION INSTRUCTIONS
LIGHTGUARD 350-20-WTC SEALED FIBER OPTIC CLOSURE VIEW ONLINE TABLE OF CONTENTS: GENERAL...2 SPECIFICATIONS...2 PACKAGE CONTENTS...3 PACKAGE CONTENTS: ACCESSORIES...3 RECOMMENDED TOOLS...3 ADD-ON COMPONENTS...4
More informationCable ISOBUS Active Termination
ISOBUS Retrofit Kit Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity ISOBUS Retrofit Kit 4100843 1 Hex Head Bolt
More informationNHD YF-CTXI# TFT
User s Guide NHD-1.8-128160YF-CTXI# TFT (Liquid Crystal Display Graphic Module) 1.8 Diagonal 8/16 - bit interface 128x160 Resolution (portrait mode) White LED Backlight Tel: (847) 844-8795 Fax: (847) 844-8796
More informationPowerBook G4 Aluminum 12" GHz LCD panel upgrade
PowerBook G4 Aluminum 12" 1-1.5 GHz LCD panel upgrade Upgrade a 1400x1050 LCD panel. Written By: martin ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION The original LCD 1024x768 resolution
More informationDual extruder upgrade manual addendum to assembly manual
Dual extruder upgrade manual addendum to assembly manual This manual is intended for users that have bought the kit WITH a new printer. For user that already have their printer assembled and working, please
More information7 LCD Color Monitor 8 LCD Color Monitor OWNER S MANUAL
7 LCD Color Monitor 8 LCD Color Monitor OWNER S MANUAL INTRODUCTION OHM720, OHM820 The Clarion OHM720/OHM820 is a full-featured 7 /8 LCD Color Monitor that can be used as a stand-alone monitor, or can
More informationHQ Electromagnetic Channel Locks. For the HQ Infinity
HQ Electromagnetic Channel Locks For the HQ Infinity Table of Contents Overview... 2 Kit Contents... 2 Tools Required... 4 Installation... 4 Using the HQ Electromagnetic Channel Locks... 9 Troubleshooting...
More informationConverting ccfl slot machine monitor to led
P ford residence southampton, ny Converting ccfl slot machine monitor to led How to connect XB Series LED converter to your Inverter wire Harness.. Universal LED Backlight Kit for Laptop Screen.. Vending
More informationASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES
ASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES FOR 75 OHM AND 75 OHM HD COAXIAL CONTACTS AND MODULES Table of Contents SECTION 1 RECEIVER CONTACT ASSEMBLY INSTRUCTIONS SECTION 2 ITA CONTACT
More informationHR7012M / HR7012S. Custom Vehicle Headrests with 7 Slim Style LED LCD Satellite Monitors or Built-in DVD Player for Rear Entertainment HR7012M
S S P HR7012M / HR7012S Custom Vehicle Headrests with 7 Slim Style LED LCD Satellite Monitors or Built-in DVD Player for Rear Entertainment HR7012M HR7012S Installation Guide 128-9047 IMPORTANT NOTICE
More informationFLAT DISPLAY TECHNOLOGY
15.0 Open Frame Monitor Model Number: LOF1506xx This product is RoHS compliant SPEC No.: SAS-1008002 Version: 0.0 Issue Date: September 6, 2010 1. Introduction: 1.1 About the Product The LOF1506xx 15.0
More informationUSER MANUAL FOR THE PANEL VIEWER
Ing. J. de Wijs. Populierstraat 44, 4131 AR Vianen, the Netherlands Tel/Fax. +31 (0)347-372242 e-mail: info@dewijs-3d.com Website: www.dewijs-3d.com Design and production of stereoscopic instruments. Bank:
More informationMIL-C CLASS L COMPATIBILITY ORDERING INFORMATION
MIL-C-22992 CLASS L COMPATIBILITY ORDERING INFORMATION ORDERING INFORMATION: Connectors are supplied with removable contacts. Contacts are supplied unassembled. Also supplied are applicable accessories
More informationHQ Electromagnetic Channel Locks
HQ Electromagnetic Channel Locks Table of Contents Overview... 2 Kit Contents... 2 Tools Required... 5 Installation... 5 Using the HQ Electromagnetic Channel Locks... 10 Troubleshooting... 11 Overview
More informationLCM Assembly Techniques...
LCM Assembly Techniques... With our products we AN INTRODUCTION The following pages show the basic methods by which a touch panel could be combined with an LCD (Liquid Crystal Display) to create an LCM
More informationUser Manual Color Video Door Phone
User Manual Color Video Door Phone CMV-43A Thank you for purchasing COMMAX products. Please carefully read this User s Guide (in particular, precautions for safety) before using a product and follow instructions
More information3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN-2-4/0
3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN-2-4/0 for Jacketed Concentric Neutral (JCN) and Flat Strap Neutral Cable Instructions IEEE Std. 404 15 kv Class 150 kv BIL F CAUTION Working around energized
More informationColor TFT LCD Monitor The Art of Surveillance
Color TFT LCD Monitor The Art of Surveillance User Manual Table of contents Safety Information---------------------------------------------------- 1-3 Accessories----------------------------------------------------------------3
More information8753E, 8753ET, and 8753ES Network Analyzer Option 1D5 High Stability Frequency Reference Upgrade Kit. Applicable Upgrade Kit Model Number
Installation Note 8753E, 8753ET, and 8753ES Network Analyzer Option 1D5 High Stability Frequency Reference Upgrade Kit Network Analyzer Model Number 8753E 8753ET 8753ES Applicable Upgrade Kit Model Number
More information