WING WHITE LED WALL WASHER

Size: px

Start display at page:

Download "WING WHITE LED WALL WASHER"

Valentine Roberts
6 years ago
Views:

1 OPERATION MANUAL WING WHITE LED WALL WASHER Version 1 June 2011

Philips Selecon has packaged this product using environmentally friendly packaging.

WE HAVE DESIGNED THIS LUMINAIRE TO PROVIDE YOU WITH A SUPERIOR FITTING IN PERFORMANCE, DESIGN AND ENGINEERING. WE ARE CONFIDENT THAT IT WILL PERFORM TO YOUR EXPECTATIONS FOR MANY YEARS TO COME.

(The serial number can be found on the sticker at the top of the luminaire and on the box the luminaire was packed in). Caution! Installation is entirely at your risk.

2 Philips Selecon has packaged this product using environmentally friendly packaging. Please consider either reuse of the packaging or dispose of responsibly with your nearest recycling collection agency. THANK YOU FOR PURCHASING A PHILIPS SELECON WING WHITE LED WALL WASHER LUMINAIRE. WE HAVE DESIGNED THIS LUMINAIRE TO PROVIDE YOU WITH A SUPERIOR FITTING IN PERFORMANCE, DESIGN AND ENGINEERING. WE ARE CONFIDENT THAT IT WILL PERFORM TO YOUR EXPECTATIONS FOR MANY YEARS TO COME. We recommend making a note of the serial numbers of your purchased luminaires for future reference. (The serial number can be found on the sticker at the top of the luminaire and on the box the luminaire was packed in). Caution! Installation is entirely at your risk. Read this manual from cover to cover before attempting installation. Do not attempt installation unless you are suitably qualified. If you do not understand a point in this manual, don t guess. Don t take short cuts. If in doubt, stop! Contact Philips Selecon or one of its authorised distributors for advice. Don t be afraid to ask for help. These luminaires are not suitable for outdoor use. They do not have an IP rating. This product has the following certifications: 2of13

3 Important! Read this manual from cover to cover before attempting to install, operate or maintain the luminaires to which it relates. It contains important installation, operating, maintenance and safety procedures. The customer must strictly comply with them. Along with such procedures mentioned in this document, the customer should also observe such other procedures generally applicable to lighting equipment. Follow the instructions in this manual carefully. Philips Selecon accepts no responsibility if the customer fails to do so. For each customer, operating conditions will vary, sometimes greatly. Such variations may affect the luminaires performance. Philips Selecon has no control over the customer s unique operating environment. Hence, Philips Selecon makes no representations or warranties concerning the luminaires performance under the customer s actual operating conditions. All operating parameters must be validated for each customer application by the customer s technical experts. If the customer does not follow the installation, operating, maintenance and safety procedures in this manual, as well as those generally applicable to lighting equipment, the luminaire may not perform as expected. More seriously, it may cause property damage, personal injury or other losses. Philips Selecon accepts no liability for direct, indirect, incidental, special, or consequential damages resulting from the customer s failure to follow the installation, operating, maintenance and safety procedures in this manual or those generally applicable to lighting equipment. The foregoing limitation extends to damages for personal injury, property damage, loss of operations, loss of profits, loss of product or loss of time, whether incurred by the customer, the customer s employees or a third party. Philips Selecon used all due care in preparing this manual. However, Philips Selecon accepts no liability for errors or omissions. Philips Selecon reserves the right to change the specifications of its luminaires, or the information in this manual, without necessarily giving its customers notice thereof. Installation, operation and maintenance are entirely at the customer s risk. Philips Selecon luminaires should be installed, operated and maintained by suitably qualified personnel. Such personnel should have previous experience with lighting equipment as well as general electrical experience. This manual is intended to provide general guidance to such suitably qualified personnel. For specific guidance and technical support, contact Philips Selecon or its authorised representative. Information in this manual shall not be deemed a warranty, representation or guarantee concerning a luminaire s suitability or fitness for a specific purpose. Subject to the right to use its luminaires, Philips Selecon does not convey any right, title or interest in its intellectual property, including, without limitation, its patents, copyrights and know-how. 3of13

4 Contents Contents... 4 Product Codes... 5 Wing White LED Wall Washer Configurations... 5 Accessories... 6 Installation... 7 Electrical Installation... 7 Wing LED Applications... 7 Pan and Tilt Adjustment... 8 Accessory Installation... 8 Barndoor... 8 Colour Frame... 8 Control... 9 Manual Dimming... 9 DALI... 9 Service and Maintenance...10 End-of-life behaviour...10 Upgradeable...10 System disposal...10 LIMITED 3-YEAR WARRANTY...11 Product specification...12 Contacting Philips Selecon of13

Product Codes Wing White LED Wall Washer Configurations WWLEDLOCALT01/ WWLEDLOCALT03 White/Black Wing White LED Wall Washer fitted with local

WWLEDLOCALC01/ WWLEDLOCALC03 White/Black Wing White LED Wall Washer fitted with local control push button and Ceiling Rose Mount.

5 Product Codes Wing White LED Wall Washer Configurations WWLEDLOCALT01/ WWLEDLOCALT03 White/Black Wing White LED Wall Washer fitted with local control push button and Track Mount. WWLEDDALIT01/ WWLEDDALIT03 White/Black Wing White LED Wall Washer fitted with Dali Track Mount. WWLEDLOCALC01/ WWLEDLOCALC03 White/Black Wing White LED Wall Washer fitted with local control push button and Ceiling Rose Mount. WWLEDLOCALHC01/ WWLEDLOCALHC03 White/Black Wing White LED Wall Washer fitted with local control push button and Half Coupler Mount with 1.0m cable and plug. 5of13

6 Accessories WING WHITE LED WALL WASHER Operation Manual WWLEDBD0103 Wing LED Barndoor White exterior, Black interior WWLEDBD03 Wing LED Barndoor Black WWLEDCF03* Wing LED Colour Frame (Black) *Note: the barndoor accessory is required if you wish to use a colour frame in the Wing LED as the barndoor creates the slot to hold the colour frame. For spare parts details contact your Philips Selecon dealer or visit for the exploded drawings. 6of13

7 Installation Electrical Installation WARNING!!! Risk of fire and electric shock. This product is to be installed by a qualified electrician only. Ensure that the AC power is switched off before attempting to make any wiring connections. This fixture employs a grounded type receptacle and is not intended for connection to a two-wire, ungrounded source of supply. To avoid the chance of product damage or malfunction, disconnect power before connecting wires, and do not connect or disconnect cables (supply, data, lamps and interface cables) when voltage is supplied to the luminaire. Mains Voltage: VAC. (unit must be direct switching mains only, not via a dimmer system). When installing this fixture use wire conductor colour codes as follows: Brown - Phase, live Blue - Neutral, return Green/Yellow - Earth Notes: 1. For ceiling rose models minimum 60 C supply conductors to be used. 2. Track adapter variants are only to be fitted to approved and compatible track systems. Wing LED Applications The Wing range has been designed to meet demanding quality light level applications such as museums and galleries multiple units are required to obtain a visually even wash of light. Recommended spacing of luminaires is to have the luminaires at equal spacing to the distance from the wall. For example if the luminaires are 1.5m away from the wall the optimum spacing between the luminaires for an even wash of light would also be 1.5m. For optimum light distribution the Wing has been designed to be installed at a 45deg nominal angle as indicated. Ambient Operating Temperature: -10 C to 40 C To guarantee product lifetime, the user should ensure that the ambient temperature remains within the recommended temperature range. The Wing White LED Wall Washer is a high power LED product with high optical output. Operators of the LED modules should not look directly into the beam of the light source (especially not with magnifiers or similar optical instruments) as this may cause damage to the eyes. Further information relating to the lux levels, luminaire spacings and IES/ILUMUDAT files can be found at and 7of13

Pan and Tilt Adjustment Adjusting the pan angle Release the set screw above the joint (as shown) and adjust accordingly. Relock after adjustment.

Accessory Installation Barndoor To install the barndoor, first hook it in to the slots on the front face and swing the barndoor up.

DO NOT OVERTIGHTEN as this causes undue stresses in the parts. Secure barndoor here. DO NOT OVERTIGHTEN.

8 Pan and Tilt Adjustment Adjusting the pan angle Release the set screw above the joint (as shown) and adjust accordingly. Relock after adjustment. Adjusting the tilt angle The tilt can be adjusted by unlocking the hex screw located as shown. Re-lock after adjustment. Accessory Installation Barndoor To install the barndoor, first hook it in to the slots on the front face and swing the barndoor up. Secure the barndoor with the two hex screws in the barndoor. Tighten these using a 3mm allen key until they are secure. DO NOT OVERTIGHTEN as this causes undue stresses in the parts. Secure barndoor here. DO NOT OVERTIGHTEN. Colour Frame The colour frame slots in between the barndoor and the front of the Wing LED luminaire. Note: the barndoor accessory is required if you wish to use a colour frame in the Wing LED as the barndoor creates the slot to hold the colour frame. 8of13

Control The Wing White LED Wall Washer can be controlled using either manual control or DALI protocol. Manual Dimming A short push on the button represents the On/Off command.

9 Control The Wing White LED Wall Washer can be controlled using either manual control or DALI protocol. Manual Dimming A short push on the button represents the On/Off command. Personal light levels can be set by a firm longer push on the push button. Failure proof (non volatile) memory ensures that the driver always remembers your setting when next time switched on or in case of power failure. Maximum number of drivers is 28 luminaires connected in one circuit (switched on buy one or multiple switches) Ignore status, < 0.04 sec. To avoid reaction on mains spikes Short push, between 0.04 sec and 0.5 sec. Switch On/Off Long push, between 0.5 sec. and 10 sec. Dim Up/Down Reset push, > 10 sec. Set light to mid value (35% output) Notes: 1. The dim direction will toggle after each individual push. Except when the value is lower than 10% it will always dim up, and when the light output is higher than 70% it will always dim down to perform according human perception 2. First digital regulating steps (DALI) are fixed at 1% light output (dimming specification) DALI The Digital Addressable Lighting Interface (DALI) is a digital protocol for controlling lighting components, such as electronic ballasts and dimmers, in buildings. Please refer to the diagram below for a typical DALI wiring configuration: 9of13

10 Service and Maintenance Philips Selecon has manufactured this luminaire in accordance with recognised best practices to recommended international safety standards. It is your responsibility to maintain this luminaire in good and safe working condition. The light emitting region on the front of the Wing White LED Wall Washer should be kept free from dirt, grease and other contaminants in order maintain optimal performance. Use only a soft, dry, lint-free cloth to clean the optics. Never use cleaning solvents as these may damage the optics. The above are the only maintenance tasks that can be safely carried out by non-approved personnel. For all other service and maintenance issues, please contact your Philips Selecon dealer. Repairs should only be carried out by suitably qualified persons. Do not operate the luminaire with damaged cable, track adapters etc. Only replace damaged parts with authorised spares. End-of-life behaviour Unlike typical conventional light sources, LEDs are not subject to sudden failure or burnout. There is no time at which the light source will cease to function. Instead, the performance of LEDs shows gradual degradation over time. When used according to specification, Wing White LED modules are predicted to deliver an average of 70% of their initial intensity after 35,000 hours operation. The life of the system is therefore more dependent on the other electronic system components and soldering methods. Upgradeable The simple modular configuration of the Wing White LED Wall Washer units this allows the units to be easily upgraded. As LED technology improves there higher performance modules will become available. These will be easy to swap in to the Wing LED units in order to upgrade them to the best possible version available without having to purchase a whole new unit. System disposal At the end of their (economic) lifetime, appropriate disposal of the Wing White LED Wall Washer unit, and it s components, is recommended. The modules are basically normal pieces of electronic equipment containing components that at present are not considered to be harmful to the environment and that can be disposed of with normal care. It is therefore recommended to dispose of these parts as normal electronic waste, according to local regulations. 10of13

11 LIMITED 3-YEAR WARRANTY Philips Selecon warrants its luminaires against defects in materials or workmanship. The term of this warranty is based on the product usage and is from the date of delivery. Architectural, Display relates to typical usage such as display lighting in a Museum viz: hrs per day, seven days per week. This warranty is void in any of the following circumstances: (a) The luminaire has been misused, neglected, damaged or abused. (b) The luminaire has been improperly installed, operated, repaired or maintained. (c) The luminaire has been modified. (d) The luminaire has been connected to other equipment with which it is not compatible. (e) The luminaire has been used or stored in conditions outside its electrical or environmental specifications. (f) The luminaire has been used for purposes other than for which it was designed. (g) The luminaire has been used outside its stated specifications and operating parameters. Correct installation of the luminaire is the owner s responsibility. To assert a warranty claim, complete Philips Selecon s return authorisation form (available from Philips Selecon). Return the luminaire to Philips Selecon or its authorised agent. If Philips Selecon accepts the warranty claim, Philips Selecon will provide, or arrange for, service, repair or replacement as Philips Selecon shall determine in its sole discretion. Philips Selecon shall bear the cost of such service, repair or replacement. However, the owner shall bear the cost of freight and insurance on the luminaire, both ways. If Philips Selecon does not wish to service, repair or replace the defective luminaire, it shall refund the purchase price. Philips Selecon s sole responsibility is to repair, replace or service a luminaire subject to a valid warranty claim. Under no circumstance will Philips Selecon be liable for direct, indirect, incidental, special or consequential costs or damages, including dismantling and re-installation costs, loss of operations or profits, to the maximum extent permitted by law. Philips Selecon accepts no liability for personal injury or property damage resulting from failure to heed relevant operating and safety procedures specified by Philips Selecon or imposed by law. This is an express warranty. Philips Selecon disclaims any other express or implied warranties, including warranties of merchantability or fitness for purpose, to the maximum extent permitted by law. Some jurisdictions do not allow limitations or disclaimers of implied or statutory warranties. Some jurisdictions do not allow disclaimers or exclusions of consequential or incidental damages. Therefore, the above disclaimers, limitations and exclusions may not apply in all jurisdictions in which Philips Selecon sells its luminaires. This warranty gives the owner specific legal rights. The owner may have other rights or remedies pursuant to the laws in its territory. Nothing in this limited warranty should be construed as limiting or restricting any other statutory right or remedy of the owner, except for such limitations or restrictions herein as may be allowed by the law of the territory. Philips Selecon has a policy of continual product improvement and specifications are subject to change without notice. 11of13

12 Product specification Maximum Power Consumption: 36W Input Voltage: V Lumen 50k hrs: 70% Colour Temperature: 3000K Control Interface: Dali or Touch Dim Ambient Operating Temperature: Minimum -10 C Maximum 40 C UV and IR PET Value Damage Factor IR (infrared) radiation >100hrs/Klux (zero UV) 4100K As well as being free of UV radiation, the Wing LED modules are also free of infrared radiation in the beam. 12of13

13 Contacting Philips Selecon Philips Selecon Kawana Street, Northcote, Auckland 1310, New Zealand Tel: , Fax: Philips Entertainment European Service & Distribution Centre Marssteden 152 Enschede 7547 TD the Netherlands Phone: Fax: Philips Strand Lighting USA Strand Lighting Petal Street Dallas, TX Tel: Support Main Fax: Strand Lighting Asia Limited 20/F Delta House 3 On Yiu Street Shatin, N.T. Hong Kong Tel: +(852) Fax: +(852) Please contact us, or check our web site to find the Philips Selecon distributor nearest to you. 13of13

WING RGB LED WALL WASHER

OPERATION MANUAL WING RGB LED WALL WASHER Version 1.3 June 2011 Philips Selecon has packaged this product using environmentally friendly packaging. Please consider either reuse of the packaging or dispose