OP+LBR+D / OP+LBT+13D and OP+LBT+CxxD L-Band Satellite Wideband Optical Receiver / L-Band Satellite Optical Transmitters

Transcription

1 Installation and Operation Manual OP+LBR+D / OP+LBT+13D and OP+LBT+CxxD L-Band Satellite Wideband Optical Receiver / L-Band Satellite Optical Transmitters Edition B Delivering the Moment

2 Publication Information 2014 Imagine Communications Corp. Proprietary and Confidential. Imagine Communications considers this document and its contents to be proprietary and confidential. Except for making a reasonable number of copies for your own internal use, you may not reproduce this publication, or any part thereof, in any form, by any method, for any purpose, or in any language other than English without the written consent of Imagine Communications. All others uses are illegal. This publication is designed to assist in the use of the product as it exists on the date of publication of this manual, and may not reflect the product at the current time or an unknown time in the future. This publication does not in any way warrant description accuracy or guarantee the use for the product to which it refers. Imagine Communications reserves the right, without notice to make such changes in equipment, design, specifications, components, or documentation as progress may warrant to improve the performance of the product. Trademarks 6800+, ADC, CCS Navigator, Channel ONE, ChannelView, ClipSync, Delay, D Series, D Series DSX, Deliver the Moment, Delivering the Moment, FAME, Farad, G8, G Scribe, HView, IconMaster, IconLogo, IconStation, IconKey, InfoCaster, InfoCaster Creator, InfoCaster Manager, InfoCaster Player, InstantOnline, Invenio, Live Update, mcapture, Magellan, Magellan CCS Navigator, Magellan Q SEE, MultiService SDN, NetPlus, NetVX, NewsForce, Nexio G8, Nexio AMP ChannelView, Nexio Channel ONE, Nexio ClipSync, Nexio Delay, Nexio Digital Turnaround Processor, Nexio Farad, Nexio G Scribe, Nexio IconKey, Nexio IconLogo, Nexio IconMaster, Nexio IconStation, Nexio InfoCaster, Nexio InfoCaster Creator, Nexio InfoCaster Manager, Nexio InfoCaster Player, Nexio InfoCaster Traffic, Nexio InstantOnline, Nexio mcapture, Nexio News- Force, Nexio NXIQ, Nexio Playlist, Nexio Remote, Nexio RTX Net, Nexio TitleMotion, Nexio TitleOne, Nexio Velocity ESX, Nexio Velocity PRX, Nexio Velocity XNG, Nexio Volt, OPTO+, Panacea, Platinum, Playlist, Predator II GRF, Predator II GX, Punctuate, Remote, RTX Net, QuiC, Q SEE, SD STAR, Selenio, Selenio 6800+, SelenioNext, Selenio X50, Selenio X85, Selenio X100, TitleMotion, TitleOne, Velocity ESX, Velocity PRX, Velocity XNG, Versio, Videotek SD STAR, X50, and X85 are trademarks of Imagine Communications or its subsidiaries. Altitude Express, Connectus, Enabling PersonalizedTV, ICE Broadcast System, ICE Illustrate, ICE Q algorithms, ICE- PAC, Imagine ICE, Inscriber, Inscriber Connectus, Invenio, NEO, Nexio, Nexio AMP, PersonalizedTV, Router- Works, Videotek, Videotek ASI STAR, Videotek GEN STAR, and Videotek HD STAR are registered trademarks of Imagine Communications or its subsidiaries. Microsoft and Windows are registered trademarks of Microsoft Corporation. HD BNC is a trademark of Amphenol Corporation. Some products are manufactured under license from Dolby Laboratories. Dolby and the double D symbol are registered trademarks of Dolby Laboratories. DTS Neural audio products are manufactured under license from DTS Licensing Limited. DTS and the Symbol are registered trademarks & the DTS Logos are trademarks of DTS, Inc DTS, Inc. All other trademarks and trade names are the property of their respective companies. Contact Information Imagine Communications has office locations around the world. For locations and contact information see: us/ Support Contact Information For support contact information see: Support Contacts: support/ ecustomer Portal: Imagine Communications Corp. Proprietary and Confidential

3 OP+LBR+D L-Band Satellite Wideband Optical Receiver OP+LBT+13D OP+LBT+CxxD L-Band Satellite Optical Transmitters Installation and Operation Manual Edition B April 2008

4

5 Contents Preface Manual Information...v Unpacking/Shipping Information... vii References... viii Safety Standards and Compliances... ix Chapter 1: Introduction Product Description...2 General Description...2 Main Features...2 Module Types Typical Broadcast and Production Applications...4 Module Descriptions...5 Front Modules...5 Back Modules...6 Signal Flow...7 OP+LBR+D Receiver...7 OP+LBT+13D/OP+LBT+CxxD Transmitter...7 Chapter 2: Installation Maximum Frame Power Ratings...10 Unpacking the Module...11 Preparing the Product for Installation...11 Checking the Packing List...11 Setting the Jumpers...12 Installing and Removing the Modules...14 Installation Overview...14 Back Module Installation...15 Front Module Installation...15 Removing Modules...17 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual iii

6 Contents Inspecting and Cleaning Fiber Optic Connections Important Points Inspection and Cleaning Procedure Chapter 3: Operation CCS Parameters LEDs and Alarms LEDs Alarms Chapter 4: Specifications Laser Output OP+LBR+ Specifications OP+LBT+ Specifications Power Consumption Start-Up Time Temperature Appendix A: Laser Safety Guidelines Laser Safety Precautions for Enclosed Systems Precautions for Unenclosed Systems Labels Index Keywords iv OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

7 Preface Manual Information Purpose Audience Revision History This manual details the features, installation procedures, operational procedures, and specifications of the OP+LBR+D L-Band Satellite Wideband Optical Receiver module and the OP+LBT+13D and OP+LBT+CxxD L-Band Satellite Optical Transmitter modules. This manual is written for engineers, technicians, and operators responsible for the installation, setup, and operation of the OP+LBR+D L-Band Satellite Wideband Optical Receiver module, as well as the OP+LBT+13D and OP+LBT+CxxD L-Band Satellite Optical Transmitter modules. Table P-1. Manual Revision History Edition Date Revision History Edition A January 2008 Preliminary Edition B April 2008 Initial release OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual v

8 Preface Writing Conventions To enhance your understanding, the authors of this manual have adhered to the following text conventions: Table P-2. Manual Style and Writing Conventions Term or Convention Bold Italics CAPS Description Indicates dialog boxes, property sheets, fields, buttons, check boxes, list boxes, combo boxes, menus, submenus, windows, lists, and selection names. Indicates addresses, the names of books or publications, and the first instances of new terms and specialized words that need emphasis. Indicates a specific key on the keyboard, such as ENTER, TAB, CTRL, ALT, or DELETE. Code Indicates variables or command-line entries, such as a DOS entry or something you type into a field. > Indicates the direction of navigation through a hierarchy of menus and windows. hyperlink Internet address NOTE Indicates a jump to another location within the electronic document or elsewhere Indicates a jump to a website or URL Indicates important information that helps to avoid and troubleshoot problems. Obtaining Documents Technical documents can be viewed or downloaded from our website. Alternatively, contact your Customer Service representative to request a document. vi OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

9 Preface Unpacking/Shipping Information This product was carefully inspected, tested, and calibrated before shipment to ensure years of stable and trouble-free service. 1. Check equipment for any visible damage that may have occurred during transit. 2. Confirm that you have received all items listed on the packing list. 3. Contact your dealer if any item on the packing list is missing. 4. Contact the carrier if any item is damaged. 5. Remove all packaging material from the product and its associated components before you install the unit. In the unlikely event that your product fails to operate properly, please contact Customer Service to obtain a Return Authorization (RA) number, then send the unit back for servicing. Keep at least one set of original packaging in the event that a product needs to be returned for service. If the original package is not available, you can supply your own packaging as long as it meets the following criteria: The packaging must be able to withstand the product s weight. The product must be held rigid within the packaging. There must be at least 2 in. (5 cm) of space between the product and the container. The corners of the product must be protected. Ship products back to us for servicing prepaid and, if possible, in the original packaging material. If the product is still within the warranty period, we will return the product prepaid after servicing. OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual vii

10 Preface References ITU-T G.694.2: Spectral grids for WDM applications: CWDM wavelength grid ITU-T G.695: Optical interfaces for coarse wavelength division multiplexing applications ITU-T G.652: Characteristics of a single-mode optical fiber cable IEC : Fiber optic connector interfaces - Part 4-1: Type SC connector family - Simplified receptacle SC/PC connector interfaces IEC : Detail specification for fiber optic connector type SC/PC tuned terminated to single-mode fiber type B1 IEC : Specifications for the fiber optic connector type ST/PC terminated to a type BFOC/2,5 IEC : Specifications for the fiber optic connector type FC/PC IEC : Detail specification for fiber optic connector type SC/PC untuned terminated to single-mode fiber type B1 FCC Code of Federal Regulations (CFR) 47, part 15 EN : EMC emission requirements applies to professional audio, video, audio-visual and entertainment lighting control apparatus EN : EMC immunity requirements applies to professional audio, video, audio-visual and entertainment lighting control apparatus viii OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

11 Preface Safety Standards and Compliances See Laser Safety on page 36 to find the safety standards and compliances for this OPTO+ series product. A series safety manual is shipped with every FR6802+ Frame Installation and Operation Manual and can be downloaded from our website. Alternatively, contact your Customer Service representative for a copy of this safety manual. Restriction on Hazardous Substances (RoHS) Directive The European Union (EU) Directive 2002/95/EC commonly known as Restriction on Hazardous Substances (RoHS) sets limits on the use of certain substances found in electrical and electronic equipment. The intent of this legislation is to reduce the amount of hazardous chemicals that may leach out of landfill sites or otherwise contaminate the environment during end-of-life recycling. The Directive took effect on July 1, 2006, and it refers to the following hazardous substances: Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent Chromium (Cr-V1) Polybrominated Biphenyls (PBB) Polybrominated Diphenyl Ethers (PBDE) According to this EU Directive, all products sold in the European Union are fully RoHS-compliant and lead-free. (See our website for more information.) Spare parts supplied for the repair and upgrade of equipment sold before July 1, 2006 are exempt from the legislation. Equipment that complies with the EU directive are marked with a RoHS-compliant emblem, as shown in Figure P-1. Figure P-1. RoHS Compliance Emblem OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual ix

12 Preface Waste from Electrical and Electronic Equipment (WEEE) Directive The European Union (EU) Directive 2002/96/EC commonly known as Waste from Electrical and Electronic Equipment (WEEE) deals with the collection, treatment, recovery, and recycling of electrical and electronic waste products. The objective of the WEEE Directive is to assign the responsibility for the disposal of associated hazardous waste to either the producers or users of these products. Effective August 13, 2005, producers or users are required to recycle electrical and electronic equipment at end of its useful life, and may not dispose of the equipment in landfills or by using other unapproved methods. (Some EU member states may have different deadlines.) In accordance with this EU Directive, companies selling electric or electronic devices in the EU will affix labels indicating that such products must be properly recycled. (See our website for more information.) Contact your local sales representative for information on returning these products for recycling. Equipment that complies with the EU directive is marked with a WEEE-compliant emblem, as shown in Figure P-2. Figure P-2. WEEE Compliance Emblem x OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

13 Preface Safety Terms and Symbols This product manual uses the following safety terms and symbols to identify certain conditions or practices. See Laser Safety on page 36 and the FR6802+ Safety Instructions and Standards Manual for more information. Table P-3. Safety Terms and Symbols WARNING: Identifies conditions or practices that can result in personal injury or loss of life high voltage is present. Uninsulated dangerous voltage within the product s enclosure may be sufficient to constitute a risk of electric shock to persons. CAUTION: Identifies conditions or practices that can result in damage to the equipment or other property. Important operating and maintenance (servicing) instructions are included in the literature accompanying the product. OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual xi

14 Preface xii OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

15 Chapter 1 Introduction Overview The OP+LBR+D module is an L-Band Satellite Wideband Optical Receiver and the OP+LBT+13D and OP+LBT+CxxD modules are L-Band Satellite Optical Transmitters for single-mode fiber applications. This chapter introduces the different versions of the modules. The following topics are described in this chapter: Product Description on page 2 Module Descriptions on page 5 Signal Flow on page 7 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual 1

16 Chapter 1: Introduction Product Description General Description Main Features The OP+LBT+13D and OP+LBT+CxxD modules are wideband RF amplification and electrical-to-optical conversion modules that amplify L-band RF signals from an Low Noise Block (LNB) output and modulate them onto lightwave. The optical signal from the OP+LBT+13D or OP+LBT+CxxD is transported over single mode fiber and fed into an OP+LBR+D. The OP+LBR+D is an optical-to-electrical conversion module that receives an optical signal from an OP+LBT+13D or OP+LBT+CxxD and converts it to an electrical signal. All of the modules have an auxiliary electrical RF output. OP+LBR+D Receiver The following features are included in the OP+LBR+D module: Extended L-band frequency from 250 MHz to 2250 MHz Manual and automatic output level settings Transparent transmission of all video, audio, and data modulation protocols Additional amplified RF output for monitoring or distribution Full hot-swapping capability Dual electrical outputs supporting 75Ω F-type connectors Available SC/PC, ST/PC, and FC/PC optical connectors (the SC/PC connector is supplied standard) CCS control and monitoring compatibility 2 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

17 Chapter 1: Introduction OP+LBT+ Transmitters The following features are included in the OP+LBT+13D and OP+LBT+CxxD modules: Wide operational frequency range from 250 MHz to 2250 MHz Wide dynamic range RF input (-60 to -10 dbm) Protocol transparency, transmitting all video, audio, and data modulation formats Additional amplified RF output for monitoring or distribution Manual and automatic output level settings Remote LNB, powered with configurable +13 V or +18 V supply, with up to 450 ma DC current at +13 V; 330 ma at +18 V Full hot-swapping capability Single wavelength and CWDM wavelength availability Support for 75Ω F-type connector Available SC/PC, ST/PC, and FC/PC optical connectors (the SC/PC connector is supplied standard) CCS control and monitoring compatibility OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual 3

18 Chapter 1: Introduction Module Types Table 1-1 describes the different versions of the OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD products. These modules cannot be installed in FR6802+DM or 6800/7000 series frames. Table 1-1. OP+LBR+D and OP+LBT+13D/OP+LBT+CxxD Modules Module Name Description Optical-to-Electrical Conversion (Receiver) OP+LBR+D Analog optical-to-analog conversion module with one optical input and two amplified RF outputs Electrical-to-Optical Conversion (Transmitters) OP+LBT+13D OP+LBT+CxxD Analog electrical-to-optical conversion module with one RF input, one constant power electrical RF output and one optical output at 1310 nm to single mode fiber Analog electrical-to-optical conversion module with one RF input, one constant power electrical RF output and one optical output at one of 16 CWDM wavelength options to single mode fiber Typical Broadcast and Production Applications OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD modules are used by broadcast, telecommunication, and cable companies to transport L-band signals from remote satellite installations to their main production facilities. Since the signal can be carried over a longer distance using a fiber-optic line, satellite installations can be located farther away from the main production facilities. 4 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

19 Chapter 1: Introduction Module Descriptions Front Modules OP+LBR+ OP+LBT+ Figure 1-1. OP+LBR+ and OP+LBT+ Front Modules OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual 5

20 Chapter 1: Introduction Back Modules OP+LBR+ OP+LBT+ Figure 1-2. OP+LBR+ and OP+LBT+ Back Modules 6 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

21 Chapter 1: Introduction Signal Flow OP+LBR+D Receiver Figure 1-3. OP+LBR+D Signal Flow OP+LBT+13D/OP+LBT+CxxD Transmitter Figure 1-4. OP+LBT+13D/OP+LBT+CxxD Signal Flow OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual 7

22 Chapter 1: Introduction 8 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

23 Chapter 2 Installation Overview This chapter describes the installation process, including the following topics: Maximum Frame Power Ratings on page 10 Unpacking the Module on page 11 Setting the Jumpers on page 12 Installing and Removing the Modules on page 14 Inspecting and Cleaning Fiber Optic Connections on page 18 See the FR6802+ Frame Installation and Operation Manual for general information about installing and operating FR6802+ frames and their components. OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD modules cannot be installed in FR6802+DM or 6800/7000 series frames. CAUTION Before installing this product, read the Series Safety Instructions and Standards Manual that is shipped with every FR6802+ Frame Installation and Operation Manual or available on our website. The safety manual contains important information about the safe installation and operation of OPTO+ series products. Also see Laser Safety Guidelines on page 35 of this manual. OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual 9

24 Chapter 2: Installation Maximum Frame Power Ratings Table 2-1. Frame Power Ratings Frame Type Power Supply OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD modules operate only in fan-cooled FR6802+ frames, subject to the limitations shown in Table 2-1. These modules cannot be installed in FR6802+DM or 6800/7000 series frames. CAUTION To maintain proper temperatures, ensure the front panel is closed at all times, and that the fan module is fully operational. Max. Frame Power Dissipation Number of Usable Slots * Max. Power Dissipation Per Slot OP+LBR+ and OP+LBT+Power Requirements FR6802+XF AC 120 W 20 6 W 2.56 W FR6802+XF48 DC 105 W W (OP+LBR+D) 11.9 W FR6802+QXF AC or DC 120 W 20 6 W (OP+LBT+13D or OP+LBT+CxxD) * Each front module requires two of these slots. Therefore, to calculate the maximum power dissipation available per module, double the rating shown in the Max. Power Dissipation Per Slot column. 10 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

25 Chapter 2: Installation Unpacking the Module Preparing the Product for Installation Checking the Packing List Before you install the modules, do the following: Check the equipment for any visible damage that may have occurred during transit. Confirm receipt of all items on the packing list. See Checking the Packing List below for more information. Remove the anti-static shipping pouch, if present, and all other packaging material. Retain the original packaging materials for possible reuse. See Unpacking/Shipping Information on page vii for information about returning a product for servicing. Contact your Customer Service representative if parts are missing or damaged. Table 2-2. Packing List Ordered Product Content Description OP+LBR+D One OP+LBR+D front module One double-slot OP+LBR+ back module One OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual OP+LBT+13D OP+LBT+CxxD One OP+LBT+13D or OP+LBT+CxxD front module One double-slot OP+LBT+ back module One OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual 11

26 Chapter 2: Installation Setting the Jumpers The OP+LBT+ modules use two jumpers: LNB power (on or off) LNB power settings (13 V or 18 V) The OP+LBR+ module does not use jumpers or switches. LNBP Jumper (J1) VLT Jumper (J2) Figure 2-1. OP+LBT+ Jumpers To set the LNB power: 1. Locate jumper LNBP (J1) on the module. Figure 2-1 shows the location of the LNBP (J1) jumper. 2. Do either of the following: Place a jumper on pins 1 and 2 to set LNB power to Off. 12 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

27 Chapter 2: Installation Place a jumper on pins 2 and 3 to set the LNB power to On. See Figure 2-2. LNBP off LNBP on Figure 2-2. Setting LNB Power Off/On To set the power voltage: 1. Locate jumper VLT (J2) on the module. Figure 2-1 shows the location of the VLT (J2) jumper. 2. Do either of the following: Place a jumper on pins 1 and 2 to set the voltage to 13 V (default). Place a jumper on pins 2 and 3 to set the voltage to 18 V. See Figure V 18 V Figure 2-3. LNB Power Voltage Settings OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual 13

28 Chapter 2: Installation Installing and Removing the Modules Installation Overview Front modules and back modules in the OPTO+ series have plastic caps that protect the fragile laser connections from damage. You must remove these protective covers before you install the front modules and back modules (see Figure 2-4). In addition, all fiber optic connections must be inspected and cleaned before they are assembled. Carefully follow the inspection and cleaning steps described in the next pages. Additional safety information begins on page 36. CAUTION Ensure that you remove the fiber optic protective covers from the front modules and back modules before installation. Do not touch the fiber optic connections. Thoroughly clean the connections before installation. Remove power from the frame before installing or removing back modules. Remove this protective cover Remove these protective covers Figure 2-4. Protective Covers for Laser Connectors 14 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

29 Chapter 2: Installation Back Module Installation Front Module Installation Follow these steps to install the back module into an FR6802+XF, FR6802+XF48, or FR6802+QXF frame: 1. Remove a blank back plate from the frame. Do not discard the blank back plates. They may be needed for future configurations. 2. On the side of the back module that inserts into the front module, remove the inner protective cap from the fiber connection (see Figure 2-4 on page 14). CAUTION Microscopic dust or other contaminants can seriously impair or disable a fiber optic network. Observe strict cleaning procedures. Do not touch the end of the fiber. 3. Follow the inspection and cleaning procedure that begins on page If the front module is already installed, remove it from the slot. 5. Install the new back module by inserting the bottom lip into the required frame slot, and then screwing it into place. Ensure that the EMI gaskets on the right side of the back module remains in place during the installation. The EMI gaskets fit tightly. 6. Apply the adhesive label to the back module if the label is supplied separately. OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD front modules are hot-swappable and can be installed with the power supply either turned on or turned off. Follow these steps to install the front modules: 1. Pull out the finger-release screws on the right and left side of the front panel of the frame, and then open it. 2. Locate the front module slot that corresponds to the matching back module. OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual 15

30 Chapter 2: Installation 3. Gently remove the outer and inner protective caps from the laser connections. (see Figure 2-4 on page 14). CAUTION Microscopic dust or other contaminants can seriously impair or disable a fiber optic network. Observe strict cleaning procedures. Do not touch the end of the fiber. 4. Follow the fiber cleaning instructions that begin on page Ensure that your front module matches with a corresponding back module of the same name and then slide the module into the guides on the frame floor. 6. When the module edge is flush with the guide, close the extractor handle. The module is properly seated when its edge is flush with the guide edge and the extractor handle closes. 7. Close the front panel to ensure proper frame ventilation. To prevent overheating, keep the front panel closed and all back module plate slots covered when you are operating the module. 16 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

31 Chapter 2: Installation Removing Modules NOTE The removal steps provided here are similar to those outlined in your FR6802+ Frame Installation and Operation Manual. Refer to that manual for detailed information about installing and operating an FR6802 frame and its components. Front Module Back Module Follow these steps to remove a front module from an FR6802+ frame: 1. Pull out the finger-release screws on the right and left side of the front panel of the frame, and then open it. 2. Grasp the extractor handle on the installed module, and then pull the module out of its slot; use the handle as a lever. 3. Close the front panel to ensure proper frame ventilation. Follow these steps to remove a back module from an FR6802+ frame: 1. Turn off the power to the frame. 2. Remove the front module, as described above. 3. Unscrew the top of the corresponding back module, and then tip it towards you. 4. Pull the bottom lip of the back module from its slot. 5. Reinstall a new or blank back plate in the empty slot to ensure proper frame ventilation. 6. Reinstall the front module, and then repower the frame. OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual 17

32 Chapter 2: Installation Inspecting and Cleaning Fiber Optic Connections Small amounts of microscopic dust or other contaminants can seriously impair or disable a fiber optic network. To ensure that your network operates reliably, you must carefully inspect and clean each connection when you install OPTO+ products. Table 2-3 lists some typical contaminants of a fiber optic connection. The inspection and cleaning procedure begins on page 20. Table 2-3. Typical Contaminants Contaminant Dust particle, 1 micron Dust particle, 9 microns Human hair Oil Film residues Powdery coatings Comments Can block up to 1% of the light transmission, creating a loss of 0.05 db Although microscopic, the particle can completely block the fiber core Typically 50 to 75 microns in diameter Frequently caused by touching Can accumulate from vapors or smoke Can be left behind after water or other solvents evaporate Important Points Before you begin cleaning, always inspect the fiber connections. Inspect and clean both fiber ends every time you make a connection. Keep a protective cap on unplugged fiber connectors. Do not touch the end of a fiber. Store unused protective caps in a clean resealable container, and keep the container nearby for easy access. Do not reuse cleaning tissues or swabs. Do not allow alcohol or another wet cleaning agent to dry on a fiber end. 18 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

33 Chapter 2: Installation Never touch the dispenser tip of an alcohol bottle or any clean portion of a tissue or swab. Use care when handling the fiber; do not twist or pull. Keep your cleaning fluids away from open flame or spark. Figure 2-5 describes the acceptable limits of defects in a fiber connection. Scratches and dust Zone 1 (0 to 20 micron diameter) No scratches or digs are allowed Zone 2 (20 to 50 micron diameter) Maximum of 3 scratches <1.0 micron width is acceptable; Maximum 1.0 micron light dig is acceptable Zone 3 (50 to 126 micron diameter) Maximum 25 micron dig is acceptable; Maximum scratch size of 1.0 micron is acceptable Maximum 25 micron diameter dig is acceptable Figure 2-5. Fiber Optic Cross-Section OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual 19

34 Chapter 2: Installation Inspection and Cleaning Procedure Inspection To inspect and clean the fibers, follow these steps: 1. Ensure the fiber is not live. WARNING Eye damage may occur if an optical instrument such as a microscope, magnifying glass, or eye loupe is used to stare at an energized fiber end. 2. Inspect the fiber endface with a fiberscope. 3. If the fiber endface is clean, return to the installation instructions on page 15 for back modules, or page 15 for front modules. If the connector is dirty, proceed to the dry cleaning instructions. Dry Cleaning If you are using cartridge or pocket-style dry cleaning tools, follow the manufacturer s directions. If you are using lint-free wipes, follow these steps: 1. Fold the lint-free wipe four to eight times into a square; do not touch the cleaning surface of the wipe. 2. Lightly wipe the fiber tip in the central portion of the lint-free wipe. CAUTION Do not scrub the fiber. Excessive rubbing will leave scratches. 3. Repeat the wiping action on another clean section of the wipe or a new wipe. 4. Inspect the connector again with the fiberscope. 5. If the connection is clean, return to the installation steps on page 15 for back modules or page 15 for front modules. If the connector is still dirty, proceed to the wet cleaning instructions. 20 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

35 Chapter 2: Installation Wet Cleaning Use 99% isopropyl alcohol and lint-free wipes to wet clean the fiber. 1. Fold the lint-free wipe four to eight times into a square; do not touch the cleaning surface of the wipe. 2. Moisten one section of the lint-free wipe with one drop of 99% alcohol; ensure that a portion of the wipe remains dry. 3. Lightly wipe the fiber end in the alcohol-moistened portion of the lint-free wipe. 4. Immediately repeat the wiping action on the dry section of the wipe, removing any residual alcohol. 5. Inspect the fiber endface again, and if necessary, repeat the wet cleaning with another clean section of the lint-free wipe. CAUTION Do not scrub the fiber. Excessive rubbing will leave scratches. 6. Dry clean any remaining residue, and then inspect the connector again. 7. If the contamination persists, repeat the dry and wet cleaning procedure until the endface is clean. If the fiber end still remains dirty after repeated cleaning attempts, call Customer Service for further instructions. If the fiber end is clean, return to the installation instructions on page 15 for back modules, or page 15 for front modules. OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual 21

36 Chapter 2: Installation 22 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

37 Chapter 3 Operation Overview This chapter describes the operation of the OP+LBR+ and OP+LBT+ modules using CCS-enabled software or control panels. None of the parameter settings can be controlled at the card edge. See the operation manuals or online help associated with the CCS products for more information on monitoring and control. The following topics are discussed in this chapter: CCS Parameters on page 24 LEDs and Alarms on page 26 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual 23

38 Chapter 3: Operation CCS Parameters The OP+LBT+13D and OP+LBT+CxxD modules have two card-edge jumpers to control the LNB power. The OP+LBR+D does not have any card-edge control. For other parameters, you must use CSS-compliant software and hardware. Table 3-1 and Table 3-2 list those parameters. Read-only parameters are indicated by gray shading and [RO] next to the parameter name. Default option settings are shown in bold. Table 3-1. OP+LBR+ Parameters in CCS Parameter Name Function Options or Values Signal Level [RO] Displays the signal level being received by the OP+LBR+ module -60 dbm to 0 dbm Optical Power [RO] Displays the optical power status -17 dbm to 1 dbm Output Signal Level Sets the output signal level when the Output Setting -40 to -20 dbm parameter is set to manual Output Setting Sets the output signal level to automatic or manual control Automatic Manual 24 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

39 Chapter 3: Operation Table 3-2. OP+LBT+ Parameters in CCS Parameter Name Function Options or Values Signal Level [RO] Displays the input L-band signal level from the satellite dish -60 dbm to 0 dbm Laser Bias [RO] Displays the laser bias value* 6 ma to 60 ma Laser Status [RO] Displays the laser status On Off LNB Status [RO] Displays the LNB power status Off 13 V 18 V Overload Output Signal Level Output Setting Sets the output signal level when the Output Setting parameter is set to manual Sets the output signal level to automatic or manual control -40 to -20 dbm Automatic Manual *The laser bias level normally increases as the laser ages. This does not affect the performance of the transmitter. Typical values are between 20 and 30 ma. OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual 25

40 Chapter 3: Operation LEDs and Alarms LEDs Figure 3-1 shows the location of the LEDs on the card edge of the front module. Table 3-3 on page 27 describes the meanings of the LEDs and their colors. Module status indicator Signal detection indicator Fiber indicator LNB power indicator (OP+LBT+ only) Figure 3-1. Card-Edge LEDs (OP+LBT+ shown) 26 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

41 Chapter 3: Operation Table 3-3. LED Descriptions LED Color Meaning When Lit Status None (off) There is no power to the module; the module is not operational. Green The module is receiving power and is operating properly. Red The module detects a major alarm; the module s initialization has failed. Red and green The module detects a minor alarm condition (see Table 3-4 on page 28). Signal Yellow The input signal is too low. Fiber Green The laser transmitter is functioning (OP+LBT+). The input optical signal is present (OP+LBR+). None (off) The optical signal is missing or is below the minimum -16 dbm threshold. (This condition activates the No Optical Input alarm on the OP+LBR+ module.) LNBP (OP+LBT+ only) Yellow (one flash/second) Yellow (five flashes/second) Yellow (solidly lit) None (off) The 13 V LNB power is on. The 18 V LNB power is on. The LNB power is overloaded. The LNB power is off. OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual 27

42 Chapter 3: Operation Alarms Table 3-4 lists the alarms that are displayed in CCS-enabled control panels and software. In addition, the card-edge module Status LED turns red when a major alarm is activated, and amber when a minor alarm is activated. Table 3-4. OP+LBR+ and OP+LBT+ CCS Alarms Alarm Name Severity Meaning Receiver (LBR) Signal Low Minor The input RF signal level has dropped below the low signal threshold value of -54 dbm. No Optical Input Major The input fiber-optic power has dropped below -16 dbm. Output Signal Level Minor The output signal level manual setting is too high and the amplifier is close to saturation. Transmitter (LBT) Signal Low Minor The input signal level has dropped below the low signal threshold value of -50 dbm. No Signal Major The input signal level has dropped below the threshold of -55 dbm. Laser Off Major The laser transmitter has failed. LNB Overload Major The input amplifier is overloaded (this rare condition is often caused by a short in the LNB power supply). Output Signal Level Minor The output signal level manual setting is too high and the amplifier is close to saturation. 28 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

43 Chapter 4 Specifications Overview The following specification information appears in this chapter: Laser Output on page 30 OP+LBR+ Specifications on page 31 OP+LBT+ Specifications on page 32 Power Consumption on page 34 Start-Up Time on page 34 Temperature on page 34 Specifications and designs are subject to change without notice. OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual 29

44 Chapter 4: Specifications Laser Output OP+LBT+ optical modules comply with laser product performance standards set by the Center for Devices and Radiological Health (except for deviations), pursuant to Laser Notice No. 50, dated July 26, Additionally, OP+LBT+ modules comply with the provisions of IEC Table 4-1. Optical Specifications for Laser Modules Laser Module Model Wavelength (nm) Output Optical Power Pulse Duration Laser Product Class/Laser Radiation Class OP+LBT+13D dbm (typical) Continuous 1/I OP+LBT+CxxD OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

45 Chapter 4: Specifications OP+LBR+ Specifications Table 4-2. OP+LBR+ Optical Input Specifications Item Specification Number of inputs 1 Signal type Analog modulated optical Connector SC/PC per IEC (standard) ST/PC per IEC (optional) FC/PC per IEC (optional) Operating wavelength Return loss Operating input power range (in conjunction with the OP+LBT+ module) 1260 to 1620 nm >40 db -15 to 2 dbm Table 4-3. OP+LBR+ Electrical Outputs Item Specification Number of outputs 2 Signal type Connector and impedance Return loss Output signal level setting range Output signal level setting error (at 1 GHz) (in conjunction with OP+LBT+) Spectrum flatness Group delay flatness Carrier-to-noise ratio Analog RF 75Ω F-type >10 db, 250 MHz to 2250 MHz -20 to -40 dbm ±2 db ±2.5 db at 250 MHz to 2250 MHz ±2.5 ns >35 db at any 36 MHz BW OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual 31

46 Chapter 4: Specifications OP+LBT+ Specifications Table 4-4. OP+LBT+ Electrical Input Specifications Item Specification Number of inputs 1 Signal type Analog RF Connector and impedance 75Ω F-type Return loss >10 db, 250 MHz to 2250 MHz Minimum input signal Ω* level Maximum input signal level Ω *A low signal alarm is triggered at -50 dbm. The transmitter will continue to function between -50 dbm and -60 dbm. Table 4-5. OP+LBT+ Electrical Output Specifications Item Specification Number of outputs 1 Signal type Analog RF Connector and impedance 75Ω F-type Return loss >10 db, 250 MHz to 2250 MHz Output signal level setting -20 to -40 dbm range Output signal level setting error (at 1 GHz) Spectrum flatness Group delay flatness Carrier-to-noise ratio ±2 db ±2 db at 250 MHz to 2250 MHz ±2.5 ns >35 db at any 36 MHz BW 32 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

47 Chapter 4: Specifications Table 4-6. OP+LBT+ Remote Powering Specifications Item Specification Number of outputs 1 Signal type Connector Voltage DC power supply 75Ω F-type Configurable 13 V and 18 V (1 V drop budgeted at cable and 12/17 V at LNB) Voltage variation ±5% Maximum current 450 ma (at 13 V); 330 ma (at 18 V) Table 4-7. OP+LBT+ Optical Output Specifications Item Specification Number of output 1 Wavelength range Optical power 1310 ±20 nm or CWDM grid +2 dbm typical Signal type Analog modulated optical Connector SC/PC per IEC (standard) ST/PC per IEC (optional) FC/PC per IEC (optional) Return loss Flatness (in conjunction with OP+LBR+) Carrier-to-noise ratio (in conjunction with OP+LBR+) >40 db ±2.5 db at 250 MHz to 2250 MHz 35 dbc at any 36 MHz BW OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual 33

48 Chapter 4: Specifications Power Consumption Table 4-8. Power Consumption Specifications Item OP+LBR+ OP+LBT+ Specification 2.56 W 11.9 W Start-Up Time The start-up time for OP+LBR+ and OP+LBT+ modules is <10 seconds. Temperature The range of operating temperatures for OP+LBR+ and OP+LBT+ modules is 32 to 113 F (0 to 45 C). 34 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

49 Appendix A Laser Safety Guidelines Overview This section describes important safety considerations when using laser modules. The following topics are included: Laser Safety on page 36 Labels on page 38 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual 35

50 Appendix A: Laser Safety Guidelines Laser Safety Optical fiber telecommunication systems use semiconductor laser transmitters that emit infrared light that is normally not visible to the human eye. Although a conventional laser produces a small beam of light, the power density is very high, and it can cause damage to your eyes. If a beam of laser light enters the eye, the eye magnifies and focuses the energy on the retina. The energy that reaches the retina can be as much as 100,000 times more than at the cornea and, as a result, it can burn the retina. Laser transmission products are classified in four major groups (Class 1, 2, 3, and 4), according to their emissions and potential for causing injury. Fiber optic transmitter modules in this series are designated Class 1. Precautions for Enclosed Systems WARNING Use of controls, adjustments, and procedures other than those specified in this document may result in hazardous laser radiation exposure. In its normal operating mode, an optical fiber communication system is totally enclosed and presents no risk of eye injury. However, if the fiber optic cables that interconnect various components of an optical fiber disconnect or break, you may be exposed to laser emissions. Also, technicians may be exposed to laser emissions during installation and servicing. Unlike some other laser designs, semiconductor lasers have a highly divergent beam that decreases rapidly with distance. The greater the distance, the less energy will enter the eye, and the less potential risk for eye injury. WARNING Eye damage may occur if an optical instrument such as a microscope, magnifying glass, or eye loupe is used to stare at the energized fiber end. 36 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

51 Appendix A: Laser Safety Guidelines Under normal operating conditions, optical fiber telecommunication systems are completely enclosed; nonetheless, observe the following precautions: 1. Do not stare into optical connectors or broken fibers. 2. Ensure technicians have satisfactorily completed an approved training course before performing installation or maintenance. 3. Ensure there are appropriate warning labels near the optical ports of the modules. Precautions for Unenclosed Systems During service, maintenance, or restoration, an optical fiber telecommunication system is considered unenclosed. Under these conditions, follow these practices: CAUTION Only authorized, trained personnel shall be permitted to do service, maintenance, and restoration. 1. Avoid exposing the eye to emissions from unterminated, energized optical connectors at close distances. 2. Ensure that only authorized, trained personnel use optical test equipment during installation or servicing. 3. Turn off all laser sources before scanning a fiber with an optical test set. 4. Keep all unauthorized personnel away from the immediate area of the optical fiber systems during installation and service. For guidance on the safe use of optical fiber communication systems in the workplace, consult ANSI Z136.2, American National Standard for Safe Use of Lasers in the U.S., or outside the U.S., IEC-60825, Part 2. OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual 37

52 Appendix A: Laser Safety Guidelines Labels The label shown in Figure A-1 is applicable to Class 1 laser products. CLASS 1 LASER PRODUCT Figure A-1. Label for Class 1 Laser Products 38 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

53 Index Keywords A Alarms, description 28 B Back modules illustration 6 installing 15 removing 17 C CCS parameters Cleaning fiber optic connections D Dry cleaning fiber optic connections 20 E Electrical input and output specifications F Features of the modules 2 Fiber optic connections cleaning cross-section (illustration) 19 dry cleaning 20 inspecting 18 wet cleaning 21 FR6802+ frames, power ratings 10 Front modules illustration 5 installing removing 17 I Inspecting fiber optic connections 18 Installing back modules 15 front modules J Jumper settings 12 L Laser output specifications 30 Laser precautions 14 16, LEDs description 27 illustration 26 LNB power, jumper setting M Modules front 5, 15 16, 17 installing types 4 OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual 39

54 Index O OP+LBR+ alarms 28 back module (illustration) 6 description 4 electrical output specifications 31 front module (illustration) 5 optical input specifications 31 parameters 24 power requirements 10 signal flow diagram 7 OP+LBT+ alarms 28 back module (illustration) 6 description 4 electrical input and output specifications 32 front module (illustration) 5 laser output specifications 30 optical output specifications 33 parameters 25 power ratings 10 remote power specifications 33 signal flow diagram 7 Optical output specifications 30, 33 P Packing list 11 Parameters, CCS Power consumption 34 LNB, jumper setting 12 ratings 10 remote specifications 33 R Removing back and front modules 17 RoHS directive ix S Safety precautions with lasers standards and compliances ix Setting jumpers 12 Shipping information vii Signal flow diagrams 7 Specifications OP+LBR+ 31 OP+LBT+ 32 power consumption 34 start-up time and temperature 34 T Temperature specifications 34 U Unpacking information vii, 11 W Warranty information ii WEEE directive x Wet cleaning fiber optic connections OP+LBR+D, OP+LBT+13D, and OP+LBT+CxxD Installation and Operation Manual

55