SAL Series Wireless Clock (V1)

Transcription

1 SAL Series Wireless Clock (V1) HIGHLIGHTS Microprocessor based movement Each clock acts as a repeater and transmitter MHz frequency hopping technology Receiving and transmission rate every four (4) hours for battery operation. Receiving and transmission rate of once a minute for 110V or 24V Internal antenna Built in diagnostic mode for easy maintenance Quick correction for time change (max. five (5) minutes) Ideal for renovation projects using existing wiring, or for new installations Energy efficient: 5 year Battery life (2 D cell)** 20 ma@ 24 VAC (voltage) 15 ma@ 110 VAC (voltage) Wide dynamic range for input voltage Battery powered (2 D cell) 7 VAC 28 VAC (24 V model) 85 VAC 135 VAC (110 V model) Does not require custom back box Smooth surface black ABS case and polycarbonate crystal Made in U.S.A. Patents pending FCC Compliant, FCC part 15 Section15,247 **Provided good reception DESCRIPTION Sapling s innovative new SAL Series wireless clocks incorporate multi function software. Every clock is capable of receiving and transmitting a signal. This type of system provides significant advantages because it is not limited to the distance or the signal path between the transmitter/receiver and the clock. Since each clock acts as a repeater and transmitter, the significant factor is the distance between one clock to another. The innovative MHz frequency hopping technology allows for a better and clearer signal even if there is interference in one of the frequencies. The SAL Series wireless clocks are designed to automatically work together without causing interference with each other. In fact, the more clocks in a specific area would increase the quality of the signal to each unit. These clocks include automatic calibration, as well as diagnostic functionality that allows the user to view the quality of the signal, how long since the last time the clock received a signal, and a comprehensive analysis of the clock itself. Sapling wireless clocks transmit a stream of data every four (4) hours (battery operated model only), and every minute (24V and 110V models). The SAL Series wireless clocks are compact, energy efficient and reliable. The clocks are available in 12 and 16 models. The SAL Series wireless clocks are FCC Compliant, part 15 Section 15,247.

2 SAL Series Wireless Clock (V1) Time base: Quartz, automatic calibration Power input: Battery (2 D cell) VAC/60 Hz 7-28 VAC/60 Hz Average current consumption: Battery - 5 year, 2 D cell** VAC VAC Power output: 8 dbm Input sensitivity: -103 dbm Operating frequency: MHz frequency-hopping technology Display: 12 or 24 hour format Color: Standard black Clock size: outer diameter, 2.18 depth outer diameter, 2.18 depth Dial: Durable polystyrene material Case: Smooth surface ABS case Crystal: Shatterproof, side molded polycarbonate crystal Temperature range: Operating: 0 C - 45 C Shelf: -15 C - 75 C Movement dimensions: (LxWxD) 7.32 x 3.46 x 1.81 Shipping box dimensions: (LxWxD) x x 3.5 Shipping weight: lbs lbs. Power kit includes: 2 - blue plastic anchor 2-10 x 1.5 sheet metal screw 1-4mm thread, 10mm length screw 1 - mounting bracket Compliance: FCC Compliant. FCC part 15 Section 15,247 **Provided good reception ARCHITECTURAL AND ENGINEERING The secondary clock shall be Sapling SAL Series wireless clock. The clock will be capable of receiving a signal from multiple clocks. The clock shall receive and transmit with MHz frequency hopping technology. The clock is to be capable of transmitting the time simultaneously without interfering with each other. The clocks shall include automatic calibration, as well as a diagnostic function that allows the user to view the quality of the signal, the last time the clock received a correction signal, a gearbox test and a comprehensive analysis of the entire clock. The clock shall have a maximum correction time of five (5) minutes. It shall be designed to be used with the Sapling Transceiver or the Sapling Repeater, which can be regulated via Sapling wireless communication protocol. Upon receipt of the wireless signal, the clock will immediately self correct. The clock shall have a semi flush smooth surface ABS case. The dial is to be made of durable polystyrene material. The crystal is to be shatterproof, side molded polycarbonate. Glass and visible molding marks are unacceptable. The clock shall have black hour and minute hands as well as a red second hand. The clock shall be FCC compliant, part 15 Section 15,247. MECHANICAL DRAWING H =.5 H1 = 1.5 H H1

3 SBL 1000 Series Wireless 2.5 and 4 Digital Clock (V1) HIGHLIGHTS Receives and transmits the signal once a minute External antenna Each clock acts as a repeater and transmitter MHz frequency hopping technology Immediate correction for time change Microprocessor based clock Available in 2.5 display and 4.0 display 12 or 24 hour format Two (2) levels of adjustable brightness Loss of communication alert Bright LED display Anti glare red or blue bezel Dynamic range for input voltages VDC (24 Volt model) VAC (24 Volt model) VAC(110 Volt model) Compatible with the SAL series analog clocks Designed to work in conjunction with the Sapling Transceiver Available in red or blue displays FCC Compliant, FCC part 15 Section 15,247 Made in the U.S.A. DESCRIPTION Sapling s new SBL 1000 Series wireless digital clocks are available with either 2.5 high characters or 4.0 high characters in a four (4) digit display. The SBL 1000 Series digital clocks are reliable slave clocks designed to work in conjunction with the Sapling Transceiver (part number STR ). The innovative MHz frequency hopping technology allows for a better and clearer signal even if there is interference in one of the frequencies. Not only can each clock receive the wireless signal, it also transmits the signal which eliminates the need for many repeaters. The SBL 1000 Series clocks are designed to automatically work together without causing interference with each other. In fact, a large number of clocks in a specific area would increase the quality of the signal to each unit. The SBL 1000 Series is based on our high efficiency, bright LED display. The clocks implement immediate correction upon receipt of the digital signal. The SBL 1000 features many options including 12 or 24 hour format, as well as two (2) brightness settings. The SBL 1000 Series digital clocks can be mounted in a surface or double mount housing. The SBL 1000 Series clock also features LEDs on the board to show if the clock is receiving data, making it easier to maintain and install. The unique, specially molded anti glare bezel gives a smooth, clean look with no visible external screws. The SBL Series wireless digital clock is FCC compliant, part 15, section 15,247.

4 SBL 1000 Series Wireless 2.5 and 4 Digital Clock (V1) Display size: 2.5 and 4.0 characters Display color: Vibrant red or blue Visibility: 100 feet 2.5 Clock 250 feet 4.0 Clock Bezel color: Anti-glare red or blue Bezel size: (LxW) 4.69 x Clock 6.75 x Clock Operating frequency: MHz frequency-hopping technology Temperature range: Operating: 0 C - 45 C Storage: C Input sensitivity: -103 dbm Power output: 8 dbm Input voltage for 2.5 clock; VDC (24 Volt) VAC (24 Volt) VAC (110 Volt) Input voltage for 4.0 clock: VDC (24 Volt) VAC (24 Volt) VAC (110 Volt) Average current 2.5 Clock consumption: (Max Brightness) VAC VAC 4.0 Clock VAC VAC Signal input: Sapling Wireless Communication Signal output: Sapling Wireless Communication Display format: 12 or 24 hour mode Brightness: 2 levels, adjustable Mounting: Surface and double mount Shipping weight: 2 lbs. 2.5 clock 3.5 lbs. 4.0 clock Shipping box dimensions: 2.5 Clock: (LxWxD) 7.5 x x Clock: (LxWxD) 9.75 x x 4.25 Power kit includes: 1-5 pin power harness 1-4 pin RS485 harness x 1/2 machine screw hex nut 1 - tooth lock washer 1 - grounding wire, loop end Compliance: UL, cul, and FCC approved, FCC part 15 Section 15,247 ARCHITECTURAL AND ENGINEERING The clock shall be a Sapling SBL 1000 wireless digital clock and shall have either a full 2.5 or 4.0 high efficiency red or blue LED numeral display. The clock will operate as a wireless digital slave clock. The clock shall receive signals from other clocks in the surrounding area or from the transceiver. The clock shall receive and transmit with MHz frequency hopping technology. The clocks will be capable of transmitting and receiving the time without interfering with each other. The clock shall have data LEDs on the board to display the receiving of data. It shall have a 12 or 24 hour display format. The clock will have two (2) levels of adjustable brightness and will feature immediate correction for time changes. The digital clock shall be capable of being installed either surface or double mount. When the input is lost, the colon on the display of the clock shall flash. The clock shall have an anti glare red or blue bezel with a smooth surface. No external screws shall be visible on the bezel or clock housing. The clock shall be FCC compliant, part 15 Section 15,247. MECHANICAL DRAWING Surface Mount Double Mount

5 STR 2000 Wireless Transceiver (V1) HIGHLIGHTS Can act as a transmitter or repeater for Sapling Wireless systems TCP/IP internet connection Frequency tuning circuit to allow for time correction with changes in temperature Field enabled Daylight Savings Time (when used as a primary master clock) Can act as an interface between existing systems to Sapling Wireless systems Can be used as a wired or wireless transceiver/repeater to Sapling Wireless systems Transmits the Sapling wireless signal to the SAL and SBL series wireless clocks MHz frequency hopping technology Can transmit up to 1000 meters in open space Loaded, half wave antenna Power output: 30 dbm (1 watt) Programmable relay output Input for interfacing with other systems such as 59 minute correction, 58 minute correction, National Time and Rauland, Dukane, Once a day dry contact closure LED display for a clear, accurate readout Simple interactive menu system Slim design makes the Wireless Transceiver versatile for mounting Easy programming via two (2) switches Analog and digital wireless clocks can be mixed on the same system RS485 input and output VAC input voltage making it accessible for American or European use Transmits wireless signal every minute Compact design makes the STR 2000 ideal for mounting in hallways FCC Approved, part 15 Section 15,247 Made in the U.S.A. DESCRIPTION Sapling's innovative multi functional transceiver is designed to wirelessly transmit data to the SAL analog wireless clock and the SBL wireless clock while receiving the time signal from an atomic clock web site via the Internet. Upon connection of the LAN cable, the atomic clock web site will start up automatically. The transceiver is also capable of receiving signals from all of the Sapling Master Clocks, as well as 59 minute correction, 58 minute correction, National Time and Rauland and Dukane. By utilizing one of the above mentioned inputs, the transceiver can transform a wired system to a wireless system. The transceiver comes equipped with a programmable auxiliary relay that can be programmed anywhere from 1 99 seconds. By utilizing this relay, interfacing with other systems via once a day closure and interfacing with intercom systems becomes effortless. In addition to the aforementioned features, the transceiver can act as a repeater while receiving a signal wired or wirelessly from the main transmitter. The transceiver has a temperature controlled time base allowing calibration of the time base during variants in temperature. The STR 2000 is very user friendly and easy to operate via two (2) switches. The transceiver has diagnostic capabilities which makes it easy to maintain. The STR 2000 can also interface with the SAM Series via the converter box, as well as the SBD 1000 digital clock and the SRM analog clock via RS485 communication. The transceiver works on MHz frequency hopping technology that allows for a better and clearer signal even if there is interference in one of the frequencies. The STR 2000 is powered using 110 volts / 60 Hz and 220 volts/50 Hz. The transceiver is FCC approved, part 15 Section 15,247.

6 STR 2000 Wireless Transceiver (V1) Time Base: Quartz crystal Frequency Aging: 5 ppm/year Frequency Stability: 5 ppm/year Input voltage: VAC, 50/60 Hz Power Input: 35 watts Input frequency: Hz Input sensitivity: -103 dbm RF signal output: 30 dbm (1 watt) Display: 0.56 seven segment LEDs Display format: 24 hour Battery backup: Ten (10) years Temperature range: Operating: 0 C - 50 C Storage: -15 C - 70 C Signal input: RS485, 59 minute, 58 minute, National Time and Rauland sync wire, once a day dry contact Signal output: RS485, Sapling Wireless Communication Internet connection: TCP/IP LAN port Output relay closures: Duration: 1-99 seconds Programmable time: HH:MM:SS format Contact rating: 8 amps, Volts Transmission frequency: MHz Calendar: Built-in calendar with leap years Programmable operation: Via two (2) switches Mounting: Wall mount Color: Gray Housing: Smooth surface metal enclosure Enclosure size: (LxWxH) 2.75 x 6.75 x 7.5 Shipping weight: 3.5 lbs. Shipping box dimensions: x x 5 Antenna length: 7 Compliance: FCC Compliant. FCC part 15 Section 15,247 ARCHITECTURAL AND ENGINEERING The Master Clock / Transmitter shall be the Sapling STR 2000 Transceiver. The transmitter shall be capable of transmitting data to the SAL wireless analog clock and the SBL wireless digital clock. The transmitter shall be capable of receiving a signal from an atomic clock web site via the Internet. The transmitter will be capable of receiving signals from all Sapling Master Clocks via RS485, as well as 59 minute correction, 58 minute correction, National Time and Rauland, and Dukane. The transmitter shall have the capability of transferring a wired system into a wireless system. The transmitter shall have a programmable auxiliary relay and shall be programmed anywhere from 1 99 seconds. Upon utilization of the relay, the transmitter will be capable of interfacing with a once a day closure or interfacing with intercom systems. The transmitter shall be capable of acting as a repeater while receiving a signal wired or wirelessly from the main transmitter. The time base shall be temperature controlled allowing calibration of the time base during temperature changes. The transmitter will have two (2) switches for operation of the menu system. The transmitter shall be capable of interfacing with the SAM Series analog clock via the Converter Box, and the SRM Series analog clock and SBD 1000 digital clock via RS485. The transmitter shall utilize MHz frequency hopping technology. The transmitter shall be FCC compliant, part 15 Section 15,247. MECHANICAL DRAWING ORDERING INFORMATION TRANSCEIVER : STR

7 GPS Master Clock (V1) HIGHLIGHTS Eight (8) channel technology Microprocessor based Immediate start up time High reliability In case of loss of signal, a temperature controlled time base is implemented allowing calibration of the time during variants in temperature Synchronized to UTC within 500 nanoseconds Interfaces directly with Sapling analog and digital clock systems Capable of working as a master for Sapling RS485 systems as well as two (2) wire digital communication systems Operation of auxiliary circuit for once a day relay closure with precise second resolution Field programmable via two (2) switches Two (2) levels of programming for technicians and end users Ten (10) year battery backup for timekeeping One (1) programmable signal duration per circuit (1 99 seconds), allowing the user to interface with other systems Diagnostic mode allows the user to maintain and troubleshoot the clock system from the master clock Converter option allows the master clock to transmit the two (2) wire signal to the secondary clocks LED Display RS232 and RS485 inputs and outputs Rack mountable FCC approved Made in the U.S.A. DESCRIPTION The GPS is a highly accurate, microprocessor based multi functional clock controller. The GPS has a Converter option which allows the two (2) wire digital communication output to be integrated into the GPS which will output 5.5 amps of current to the clock system. The GPS is equipped with a programmable auxiliary relay that can be programmed anywhere from 1 99 seconds. In case the signal is not present, the GPS will utilize a temperature controlled time base allowing calibration of the time base during variants of temperature. The GPS is easily programmable via two (2) switches. The GPS incorporates diagnostic testing which allows the user to view the current and temperature of the Converter (Converter option only), as well as a comprehensive test of the GPS. The GPS also has a RS485 output utilized for interfacing with other Sapling products. The GPS receiver comes with a RS232 input and output for serial interface in the computer. The GPS can be powered with 110 volts AC / 60 Hz or 220 volts AC / 50 Hz. It shall be FCC approved.

8 GPS Master Clock (V1) Time base: Crystal Frequency aging: 5 ppm/year Frequency stability: 5 ppm/year Voltage input: VAC, 50/60 Hz Power input: 35 watts Display: Seven (7) segment LED display Color: Standard gray Housing: Smooth surface, rack mount metal case Programmable operation: Via two (2) switches Temperature range: Operating: 0 C - 45 C Shelf: C Output relay closure Duration: 1-99 seconds Programmable time: HH : MM : SS format Contact Rating: 8 amps, volts Signal Outputs: RS485 and two (2) wire digital communication (with converter option only) Antenna: Thread mount bullet on 3/4 conduit Antenna dimensions: Diameter: 3.04 Height: 2.94 Mounting: Rack mount Standby time keeping: Ten (10) years Housing dimensions: (LxWxD) 5.25 x 19 x 6.25 Shipping Weight: Rack - 9 lbs. Shipping Box dimensions: (LxWxD) x x Includes: 1-6 foot power cord 1 - dome antenna 4-75 foot cable Compliance: FCC Approved CONVERTER OPTION SPECIFICATION Output current: 5.5 amps Output voltage: ± 24 Volts DC Diagnostic LEDs: Load tolerance LED: 80% of 5.5 Amps Temperature tolerance LED: 80% of 53 C Fans: DC brushless 60x60x25 mm 22.1 CFM 34.3 db(a) ARCHITECTURAL AND ENGINEERING The receiver shall be a Sapling GPS Receiver. The receiver shall offer a Converter option that will allow the user to send out the two (2) wire digital communication signal. The receiver shall have a programmable auxiliary relay that can be programmed anywhere from 1 99 seconds. In case the signal is lost, the receiver shall utilize a temperature controlled time base allowing calibration of the time base during variants of temperature. The receiver shall be programmable via two (2) switches. The receiver shall have diagnostic capabilities that will allow the user to view the current and temperature of the Converter (Converter option only), as well as a comprehensive test of the receiver. The receiver shall have a RS485 output for integration with Sapling products. The receiver will have a RS232 input and output for serial interfacing to a PC. The voltage input shall be 110 volts AC/60 Hz or 220 volts AC/50 Hz. The receiver shall be FCC approved. MECHANICAL DRAWING ORDERING INFORMATION: GPS GPS GPS* GPS with Converter option** * Indiana and Arizona customers use the following part number: GPS ** Indiana and Arizona customers use the following part number: GPS

9 Wireless Repeater STR 1000 Series (V!) HIGHLIGHTS Transmits the Sapling wireless signal to the SAL and SBL Series wireless clocks MHz frequency hopping technology Can transmit up to 2000 meters in open space Wirelessly receives and transmits data Loaded, half wave antenna Power input sensitivity: 103 dbm Power output: 30 dbm No need for custom back box Slim design makes the Wireless Repeater versatile for mounting Compact design Analog and digital wireless clocks can be mixed on the same system LEDs for indication of transmission or receipt of RS485 signal and wireless signal VAC input voltage making it accessible for American or European use Receives and transmits signal once a minute Made in the U.S.A. FCC Compliant, FCC part 15, section 15,247 DESCRIPTION The new Sapling Repeater is the perfect way to transmit and receive the Sapling wireless signal. The repeater is an ideal choice for extending the wireless signal to the slave clocks when long distances are involved. The repeater works on MHz frequency hopping technology. Due to its high powered module, the repeater can transmit up to 2000 meters in open space, making it perfect for installations where there are large distances between clocks. The signal is transmitted and repeated once a minute. The repeater distributes the signal to the SBL Series digital clocks and the SAL Series analog clocks. This versatility makes it simple to add analog and digital clocks on the same system. The repeater runs on 110 volts/60 Hz or 220 volts/50 Hz making it ideal for American or European systems. The repeater has a slim, compact design making mounting effortless. The housing for the repeater has knockouts, making it easy for conduit to run to it. The repeater is also FCC compliant, FCC part 15, section 15,247.

10 Wireless Repeater STR 1000 Series (V!) Input voltage: VAC, 50/60 Hz Input power: 35 watts Input frequency: Hz RF input sensitivity: -103 dbm RF power output: 30 dbm (1 Watt) Average current consumption: VAC Temperature range: Operating: 0 C - 50 C Storage: -15 C - 70 C Transmission frequency: MHz Mounting: Wall mount Knockouts: Three (3) total, 7/8 depth Color: Gray Housing: Smooth surface metal enclosure Enclosure size: (LxWxH) 2.75 x 6.75 x 7.5 Shipping weight: 3.5 lbs. Shipping box dimensions: x x 5 Antenna length: 7 Antenna gain: 2 dbi Compliance: FCC Compliant. FCC part 15 Section 15,247 ARCHITECTUAL AND ENGINEERING The repeater shall be a Sapling Wireless Repeater. The STR 1000 shall wirelessly transmit and receive data. The repeater shall be capable of transmitting to the SAL wireless analog clock and the SBL wireless digital clock. The repeater shall work on MHz frequency hopping technology. The repeater shall wirelessly transmit and receive data. The repeater is to have a maximum antenna size of seven (7) inches. The repeater shall have an RF input sensitivity of 103 dbm. The repeater is to have a RF power output of 30 dbm. The voltage input for the repeater shall be 110 volts/60 Hz or 220 volts/50 Hz. The repeater shall have three (3) knockouts with a diameter of 7 8. The case shall be a compact, smooth surface metal enclosure. The repeater is to weigh 3.5 pounds. The repeater shall be FCC Compliant, part 15 Section 15,247. MECHANICAL DRAWING ORDERING INFORMATION REPEATER : STR