Video Projector. Operating Instructions VPL-HW55ES (1)

Transcription

1 (1) Video Projector Operating Instructions Before operating the unit, please read this manual and supplied Quick Reference Manual thoroughly and retain them for future reference. VPL-HW55ES

2 Table of Contents Location of Controls Front/Right Side... 4 Rear/Bottom... 5 Remote Control... 6 Connections and Preparations Preparation 1: Installing the Projector... 7 Installing the Unit...7 Preparation 2: Adjusting the Picture Position... 8 Preparation 3: Connecting the Projector Connecting to a VCR Connecting to a Computer Connecting to a 3D Sync Transmitter Projecting Projecting the Picture Turning Off the Power Selecting the Aspect Ratio According to the Video Signal Watching 3D Video Images Using the Simulated 3D Function Using the 3D Glasses Selecting the Picture Viewing Mode Using ImageDirector3 to Adjust the Picture Quality Adjusting the Picture Quality...28 Selecting to Directly Adjust the Desired Menu Item...28 Adjusting the Picture Using Real Color Processing...29 Using the Menus Operation through the Menus...31 Picture Menu...34 Advanced Picture Menu...39 Screen Menu...40 Setup Menu...42 Function Menu...44 Items Locked by Settings Lock...47 Installation Menu...48 Information Menu...50 About the Preset Memory No Others About the Control for HDMI...52 About the x.v.color...53 About the simulated 3D feature...53 Troubleshooting...54 Warning Indicators...57 Message Lists...58 Replacing the Lamp and the Air Filter and Cleaning the Ventilation Holes (intake)...60 Cleaning the Air Filter...63 Fitting the Lens Cap...63 Cleaning

3 Specifications...65 Preset Signals...67 Input Signals and Adjustable/ Setting Items...69 Compatible 3D Signals D Signals and Adjustable/Setting Items...71 Aspect Mode...73 Storage Conditions of Adjustable/ Setting Items...74 Projection Distance and Lens Shift Range...76 Index

4 Location of Controls Front/Right Side You can use the buttons on the control panel with the same names as those on the remote control to operate the projector. Control panel Lens shift dials (1 page 9) M/m/</, (arrow)/ (enter) button (1 page 31) MENU button (1 page 31) INPUT button (1 page 17)?/1 (ON/STANDBY) switch (1 page 9) LAMP/COVER indicator (1 page 57) ON/STANDBY indicator (1 page 9) Ventilation holes (exhaust) Note While the ON/STANDBY indicator lights in orange, the power saving mode is on. (1 page 43) Remote control detector Zoom lever (1 page 11) Focus ring (1 page 11) Ventilation holes (exhaust) - AC IN socket HDMI 1 connector (1 page 13) HDMI 2 connector (1 page 13) INPUT A connector (1 page 15) Y PB/CB PR/CR connector (phono type) (1 page 14) 3D SYNC connector (1 page 16) REMOTE connector Connects to a computer, etc. for remote control IR IN connector Inputs signals to control the projector 4

5 Rear/Bottom Location of Controls Ventilation holes (intake) Ventilation holes (intake) Ventilation holes (intake) Ventilation holes (intake) Lamp cover (1 page 61) Front feet (adjustable) (1 page 12) Filter holder (1 page 62) Ventilation holes (intake) Projector suspension support attaching hole (1 page 78) 3D Sync Transmitter (1 page 24) 5

6 Remote Control LIGHT button Illuminates the buttons on the remote control. Infrared transmitter?/1 (On/standby) switch (1 page 9) INPUT button (1 page 17) CALIBRATED PRESET buttons (1 page 26) PATTERN button (1 page 9) RESET button (1 page 33) M/m/</, (arrow)/ (enter) buttons (1 page 31) MOTION ENHANCER button (1 page 28) ASPECT button (1 page 19) COLOR SPACE button (1 page 28) COLOR TEMP button (1 page 28) GAMMA CORRECTION button (1 page 28) MENU button (1 page 31) 3D button (1 page 44) RCP (Real Color Processing) button (1 page 29) REALITY CREATION button (1 page 35) ADVANCED IRIS button (1 page 28) SHARPNESS +/ button (1 page 36) CONTRAST +/ button (1 page 36) BRIGHTNESS +/ button (1 page 36) 6

7 Connections and Preparations This section describes how to install the projector and screen, how to connect the equipment from which you want to project the picture, etc. Preparation 1: Installing the Projector The projector displays pictures output from a VCR or other device. The lens shift allows you to have broader options for placing the projector and viewing pictures easily. Connections and Preparations Installing the Unit The installation distance between the unit and a screen varies depending on the size of the screen or whether or not you use the lens shift features. Install this unit so that it fits the size of your screen. For details on the distance between the unit and the screen (the projection distance) and the size of projected video, see Projection Distance and Lens Shift Range (1 page 76). 1 Position the unit so that the lens is parallel to the screen. Screen Top view 2 Project an image on the screen and adjust the picture so that it fits the screen. (1 page 8) Note When using a screen with an uneven surface, stripes pattern may rarely appear on the screen depending on the distance between the screen and the projector or the zooming magnifications. This is not a malfunction of the projector. 7

8 Preparation 2: Adjusting the Picture Position Project an image on the screen and then adjust the picture position. 1 ON/STANDBY indicator 4 Lens shift dials Remote control detector 5, 6 Zoom lever, Focus ring 2?/1 (On/ standby) switch 3 PATTERN button Tip The?/1 (ON/STANDBY), INPUT, MENU, and M/m/</,/ (joystick) buttons on the side panel of the projector function the same as those on the remote control. Note Depending on the installation location of the projector, you may not control it with the remote control. In this case, point the remote control to the screen instead of the projector. 8

9 1 After connecting the AC cord to the projector, plug the AC cord into a wall outlet. The ON/STANDBY indicator lights in red and the projector goes into standby mode. Lights in red. 2 Press the?/1 (ON/STANDBY) switch to turn on the projector. 4 Move both lens shift dials to adjust the picture position. Connections and Preparations The ON/STANDBY indicator flashes in green, and then lights in green. Flashes in green for a while (tens of seconds) and then lights in green. To adjust the vertical position To adjust the horizontal position 3 Display a test signal for performing adjustments. Press the PATTERN button on the remote control to display the test signal. Tip Press the PATTERN button to clear the test signal display. 9

10 To adjust the horizontal position Turn the lens shift dial right or left. The picture projected on the screen moves right or left by a maximum of 25% of the screen width from the center of the lens. 25% 1 screen width 25% Top view : Picture position when moving the picture to the left at maximum : Picture position when moving the picture to the right at maximum To adjust the vertical position Turn the lens shift dial up or down. The picture projected on the screen moves up or down by a maximum of 71% of the screen height from the center of the lens. Side view 71% 1 screen height 71% : Picture position when moving the picture upward at maximum : Picture position when moving the picture downward at maximum 10

11 Notes The range to move the picture projected on the screen can be adjusted only within the octagon area illustrated below. For details, see Projection Distance and Lens Shift Range (1 page 76). Range of movement of the projected picture 0.71V Projected Picture 0.25H 0.25H 0.71V Connections and Preparations H: Width of the projected picture V: Height of the projected picture When you use both the horizontal and vertical lens shift features at the same time, the distance the picture projected on the screen moves differ depending on how much the lens shift is adjusted. 5 Adjust the picture size using the zoom lever. Zoom lever 6 Adjust the focus using the focus ring. Focus ring 11

12 To adjust the tilt of the installation surface If the projector is installed on an uneven surface, use the front feet (adjustable) to keep the projector level. Turn to adjust. Front feet (adjustable) Notes Pointing the projector at too high or too low of a tilt will result in trapezoidal distortion in the projected image. Be careful not to catch your finger when turning the front feet (adjustable). Lens Focus adjustment window (test pattern) 4:3 2.35:1 1.85:1 12

13 Preparation 3: Connecting the Projector When making connections, be sure to do the following: Turn off all equipment before making any connections. Use the proper cables for each connection. Insert the cable plugs properly; poor connection at the plugs may cause a malfunction or poor picture quality. When pulling out a cable, be sure to pull it out from the plug, not the cable itself. Refer to the operating instructions of the connected equipment. Connecting to a VCR To connect to equipment with HDMI output connectors You can enjoy better picture quality by connecting a DVD player/recorder, Blu-ray Disc player/recorder, or PlayStation equipped with HDMI output to the HDMI input of the projector. Moreover, if you have a Control for HDMI compatible equipment, you can operate the projector synchronizing with the Control for HDMI compatible equipment. For details, see the Function menu (1 page 44) and About the Control for HDMI (1 page 52). Connections and Preparations Right side of the projector Equipment with HDMI output connectors AV amplifier with HDMI input/output connectors Speakers to HDMI output HDMI cable (not supplied) : Video signal flow When using an HDMI cable, be sure to use a Sony HDMI cable or another cable that has the HDMI logo. 13

14 Notes Use a high-speed HDMI cable. With a standard HDMI cable, images of 1080p, DeepColor, and 3D video images may not be displayed properly. When connecting an HDMI cable to the projector, make sure the V mark on the upper part of the HDMI input of the projector and the v mark on the connector of the cable is set at the same position. If the picture from equipment connected to the projector with an HDMI cable is not clear, check the settings of the connected equipment. To connect to equipment with component video output connectors Right side of the projector Equipment with component video output connectors AV amplifier Speakers : Video signal flow Component video cable (not supplied) 14

15 Connecting to a Computer Right side of the projector to monitor output Computer Connections and Preparations HD-Dsub15 pin cable (not supplied) or HDMI cable (not supplied) : Video signal flow When using an HDMI cable, be sure to use a Sony HDMI cable or another cable that has the HDMI logo. Notes Use a high-speed HDMI cable. With a standard HDMI cable, images of 1080p, DeepColor, and 3D video images may not be displayed properly. When connecting an HDMI cable to the projector, make sure the V mark on the upper part of the HDMI input of the projector and the v mark on the connector of the cable is set at the same position. If you set your computer, such as a notebook type, to output the signal to both computer s display and this equipment, the picture of the equipment may not appear properly. Set your computer to output the signal to only the external monitor. For details, refer to the computer s operating instructions supplied with your computer. For settings of the computer, consult with the manufacturer of the computer. If the picture from equipment connected to the projector with an HDMI cable is not clear, check the settings of the connected equipment. 15

16 Connecting to a 3D Sync Transmitter This unit incorporates a 3D Sync Transmitter. Depending on the installation environment of the unit, the 3D glasses may not receive 3D signals properly from the unit s built-in 3D Sync Transmitter. In this case, connect an optional 3D Sync Transmitter and place it near your viewing position. Right side of the projector 3D Sync Transmitter (not supplied) Tip Place the optional 3D Sync Transmitter directly facing the 3D glasses. Also, in order to stabilize operation of the 3D glasses, it is recommended that you place the 3D Sync Transmitter near your viewing position. CAUTION Be sure to use straight-type LAN cable of up to 15 m labeled TYPE CM, and do not use an extension cord. Notes The 3D SYNC connector is dedicated for the optional 3D Sync Transmitter. Do not connect computers or other network devices, to avoid malfunction. You can use a 3D Sync Transmitter separate from this unit, using an optional LAN cable (straighttype). If the usage environment has interference of a continuous specific frequency, synchronization of 3D image signals and the 3D glasses may be lost. In this case, use a LAN cable labeled Category 7. When watching 3D images in an environment that has even more interference, use the internal transmitter. Be sure to use cable of up to 15 m, and do not use an extension cord. Also, keep the LAN cable away from any AC power cords as much as possible. Only one 3D Sync Transmitter should be connected to the unit. Connecting multiple 3D Sync Transmitters may cause a malfunction. When connected to the 3D Sync Transmitter, the built-in 3D Sync Transmitter feature of the unit will turn off. You cannot use both at the same time. 16 Connecting cable : 3D sync signal flow

17 Projecting This section describes how to operate the unit to view the picture from the equipment connected to the unit. It also describes how to adjust the quality of the picture to suit your taste. Projecting the Picture 1 Power on both the projector and the equipment connected to the unit. 2 Press INPUT to display the input palette on the screen. To view the picture from RGB equipment connected to the INPUT A connector Component equipment connected to the Y PB/CB PR/CR connector Equipment connected to the HDMI 1 connector Equipment connected to the HDMI 2 connector Press INPUT to display Input-A Component HDMI 1 HDMI 2 Projecting 3 Select the equipment from which you want to display images. Press INPUT repeatedly or press M/m/ (enter) to select the equipment from which to project. Example: To view the picture from the video equipment connected to the HDMI 1 connector of this unit. Tips When Auto Input Search is set to On in the Function menu, only input terminals with effective signals are displayed in the input palette. When Status is set to Off in the Setup menu, the input palette does not appear. Press of the INPUT button to switch between input terminals in sequence. When the Control for HDMI is set to On in the Function menu, the input terminal with effective signals is automatically displayed, synchronizing with the operation of the equipment connected to HDMI 1 or HDMI 2 input of the unit. (Only when the connected equipment supports Control for HDMI compatible.) 17

18 Turning Off the Power 1 Press the?/1 (ON/STANDBY) switch. A message POWER OFF? appears on the screen. 2 Press the?/1 (ON/STANDBY) switch again before the message disappears. The ON/STANDBY indicator flashes in green and the fan continues to run to reduce the internal heat. First, the ON/ STANDBY indicator flashes quickly, during which you will not be able to light up the lamp with the?/1 (ON/ STANDBY) switch. The fan stops and the ON/STANDBY indicator changes from flashing green to remaining red. The power is turned off completely, and you can disconnect the power cord. Note Never disconnect the power cord while the indicator is flashing. You can turn off the projector by holding the?/1 (ON/STANDBY) switch for about 1 second, instead of performing the above steps. 18

19 Selecting the Aspect Ratio According to the Video Signal You can select an aspect ratio best suited for the video signal received. ASPECT button Press ASPECT. Each time you press the button, you can select the Aspect setting. You can also select it using the menu. (1 page 40) Projecting Original image Recommended setting and resultant images Wide Zoom (When an SD signal is input) 1.33:1 (4:3) 1.33:1 (4:3) with side panels Zoom (When an SD signal is input) 1.33:1 (4:3) letterbox picture 19

20 Original image Recommended setting and resultant images Normal 1.78:1 (16:9) 1.33:1 (4:3) 1.33:1 (4:3) with side panels Stretch Squeezed V Stretch 2.35:1 When using an anamorphic lens 20

21 Original image Recommended setting and resultant images Squeeze 16:9 Projecting When using an anamorphic lens Normal (When a computer signal is input) Full (When a computer signal is input) Notes Selectable aspect modes vary depending on the input signal. You can adjust the vertical position of the picture with V Center and Vertical Size in the Screen menu only when Aspect is set to Zoom. (1 page 41) Notes on switching the Aspect setting Select the aspect mode taking into account that changing the aspect ratio of the original picture will provide a different look from that of the original image. Note that if the unit is used for profit or for public viewing, modifying the original picture by switching the aspect may constitute an infringement of the rights of authors or producers, which are legally protected. 21

22 Watching 3D Video Images You can enjoy powerful 3D video images, such as from 3D games and 3D Blu-ray Discs, using the supplied 3D glasses. 1 Turn on the HDMI equipment for 3D compatibility connected to the unit, then play the 3D content. For details on how to play 3D content, refer to the operating instructions for the connected equipment. 2 Turn on the unit and project the 3D video image onto the screen. For details on how to project the image, see Projecting the Picture (1 page 17). 3 Turn on the 3D glasses, and then put them on so that they fit comfortably. For details on how to use the 3D glasses, see Using the 3D Glasses (1 page 23). Tips The factory default setting for 2D-3D Display Sel. is Auto. to allow projecting 3D video images automatically when the projector detects 3D signals. To convert 3D video images to 2D video images, set 2D-3D Display Sel. to 2D (1 page 44). Notes It may not be possible to display 3D video image, depending on the type of signal. Set the 2D-3D Display Sel. to 3D, and 3D Format to Side-by-Side or Over-Under to suit the format of the 3D content you want to watch (1 page 44). Use the 3D glasses within the communication range (1 page 24). You can watch 3D video images only when signals from HDMI input. When connecting 3D equipment such as a 3D game or 3D Blu-ray player to the unit, use an HDMI cable. There are differences in perception of 3D video images among individuals. When the temperature of the usage environment is low, the 3D effect may be diminished. Adjusting/Setting the 3D functions using the menu Press the 3D button on the remote control to adjust the 3D settings in 3D Settings in the Function menu. For details, see 3D Settings (1 page 44). 22

23 Using the Simulated 3D Function You can convert normal 2D video images to 3D video images. Tip For details on how to operate the on-screen menu, see Operation through the Menus (1 page 31). 1 Display the Function menu and select 3D Settings. 2 Set 2D-3D Display Sel. to 3D, then press, to display 3D Format. 3 Set 3D Format to Simulated 3D (1 page 44). Projecting Tip Use the supplied 3D glasses. Notes 2D-3D Display Sel. cannot be set to 3D for some video sources. For available 3D signals, see Compatible 3D Signals (1 page 71). The simulated 3D feature may have limited effect, depending on the video source. There are differences in perception of 3D video images converted by the simulated 3D function among individuals. Using the 3D Glasses The 3D glasses receive signals sent by the 3D Sync Transmitter built into the front of the unit, which are reflected to the glasses from the screen. When watching 3D video images using the 3D glasses, face squarely toward the screen. Power button LED indicator 1 Press the power button on the 3D glasses. The LED indicator lights up in green. 2 Put on the 3D glasses. 3 Turn toward the screen. IR sensor Precautions for use The 3D glasses receive infrared signals sent by the 3D Sync Transmitter built into the front of the unit, which are reflected to the glasses from the screen. Misoperation may occur if: The 3D glasses do not face the screen There are objects blocking the path between the 3D glasses and the screen The viewing position is too far from the screen or the distance between the unit and screen is too great There are other infrared communication devices nearby 23

24 3D glasses communication range Figures A and B below indicate the communication range of the 3D glasses. If you try to watch 3D video images from a distance greater than the communication range or install the projector outside the communication range, the 3D glasses may not be able to display the images properly. Also, the viable angles and distance vary depending on the screen type, environment of the room, and installation environment of the projector. Figure A: 3D glasses communication range (distance from the screen) Approx. 5 m (Maximum) 3D glasses Screen Top or side view Figure B:3D sync signal communication distance between the projector and screen Approx. 5 m (Maximum) Side view Projector Screen Note A 3D sync signal is projected towards the screen from 3D Sync Transmitter at the front of this unit. (Figure C) Installation conditions may prevent 3D sync signals from reaching the screen; for example, an obstruction in front of the unit. 24

25 Figure C Installation A 3D Sync Transmitter : 3D sync signal is blocked. Projecting Installation B When projecting downward from a unit that is recessed, if the unit is not installed on the ceiling, the signal from the 3D Sync Transmitter may not be projected properly to the screen, and the 3D glasses will not operate normally. (Installation A) Install the unit with its lens at the edge of, or outside of, the recess (Installation B). Alternatively, use the optional 3D Sync Transmitter. (1 page 16) 25

26 Selecting the Picture Viewing Mode You can select the picture viewing mode that best suits the type of video source or room conditions. You can save and use different preset modes for 2D/3D respectively. Press one of the CALIBRATED PRESET buttons. CALIBRATED PRESET buttons Setting items CINEMA FILM 1 CINEMA FILM 2 REF TV PHOTO GAME BRT CINE BRT TV USER Description Picture quality suited to reproducing the highly dynamic and clear images typical of master positive film. Picture quality suited to reproducing the rich tone and color typical of a movie theater. A picture quality setup suitable for when you want to reproduce faithfully the original image quality, or for enjoying image quality, without any adjustment. Picture quality suited for watching TV programs, sports, concerts, etc. Ideal for projecting still images taken with a digital camera. Picture quality suited to gaming, with well-modulated colors and fast response. Picture quality suited for watching movies in a bright environment, such as a living room. Picture quality suited for watching TV programs, sports, concerts, and other video images in a bright environment, such as a living room. Adjusts the picture quality to suit your taste then saves the setting. The factory default setting is the same as REF. 26

27 Using ImageDirector3 to Adjust the Picture Quality By using the ImageDirector3, you can make the desired gamma correction from a computer connected to the unit. Connect the REMOTE connector of the unit with a computer and start-up ImageDirector3 on the computer. For details on how to use ImageDirector3, refer to the Help in ImageDirector3. Notes You need to install the ImageDirector3 on a computer beforehand. ImageDirector3 can be downloaded from the Sony website. When connecting the REMOTE connector with a computer, connect while the power of the computer and the unit is off. You cannot adjust the picture quality when Gamma Correction in the Picture menu is set to Off. When you set Gamma Correction in the Picture menu to 1.8, 2.0, 2.1, 2.2, 2.4, or 2.6, ImageDirector3 displays Gamma 1, Gamma 2, Gamma 3, Gamma 4, Gamma 5, or Gamma 6, respectively. If you use ImageDirector3 while a 3D video image is displayed or a 3D signal is input, the image may be distorted. Projecting 27

28 Adjusting the Picture Quality You can easily adjust the picture quality that suits your taste by selecting the adjustment items with the remote control. The adjusted data can be stored in each calibrated preset mode. Selecting to Directly Adjust the Desired Menu Item MOTION ENHANCER button COLOR TEMP button COLOR SPACE button REALITY CREATION button ADVANCED IRIS button GAMMA CORRECTION button The following menu items can be adjusted by using the buttons on the remote control. Motion Enhancer Color Temp. Color Space Advanced Iris Reality Creation Gamma Correction Press the following buttons of the desired menu item repeatedly to adjust the picture quality to suit your taste. For details on each menu item, see the Picture menu. (1 page 34) 28

29 Adjusting the Picture Using Real Color Processing The Real Color Processing (RCP) feature allows you to adjust the color, hue, and brightness of each target of the projected picture you specify independently. You can thus obtain a picture more suitable to your taste. Tip Freeze the scene of the video source when you are adjusting the picture using Real Color Processing. Projecting 2, 3, 4, 5 M/m/</, (arrow) / (enter) buttons 1, 6 RCP (Real Color Processing) button 1 Press RCP on the remote control. 2 Press M/m to select User 1, User 2 or User 3, then press,. The RCP (Real Color Processing) window appears. to select the color you want to adjust among Red, Yellow, Green, Cyan, Blue and Magenta. Only the portions that correspond to the specified color will be colored and the other portions will be displayed in black and white. The reference palette in the RCP window also shows the adjustable colors. Select the desired setting to adjust the color on the projected image using the reference palette as a guide. 2 Press M/m to select Position or Range, and specify it more delicate color position and color range you want to adjust using </,. Reference palette 3 Select the target color you want to adjust. Repeat steps 1 and 2 described below to specify the target color. 1 Press M/m to select Color Select, then press </, 4 Adjust the color of the specified portions. Press M/m to select RCP Color, RCP Hue or RCP Brightness, then adjust the color or hue of the portions selected in step 3 to suit your taste using </, while watching the projected picture. The picture is returned to normal color during adjustment. 29

30 5 After the adjustment is completed, press. The RCP window disappears and the picture of step 2 returns. Tip There are some limitations on selection of position and range. 6 Press RCP. 30

31 Using the Menus This section describes how to make various adjustments and settings using the menus. Note The menu displays used for the explanation may be different from the actual menu display. Operation through the Menus The projector is equipped with an on-screen menu for making various adjustments and settings. Some of the adjustable/setting items are displayed in a pop-up menu, in a setting menu or adjustment menu with no main menu, or in the next menu window. If you select an item name followed by an arrow (B), the next menu window with setting items appears. 2 Press M/m to select a menu item, and press, or. The items that can be set or adjusted with the selected menu appear. The item presently selected is shown in white. Using the Menus 1 Press MENU. The menu window appears. 3 Press M/m to select an item you want to set or adjust and press, or. The setting items are displayed in a popup menu, in a setting menu, in an adjustment menu or in the next menu window. 31

32 Pop-up menu Setting menu Setting items 4 Make the setting or adjustment of an item. When changing the adjustment level To increase the value, press M/,. To decrease the value, press m/<. Press to store the setting and restore the original menu screen. When changing the setting Press M/m to change the setting. Press to restore the original screen. You can restore the original menu screen using < depending on the selected item. Items that cannot be adjusted Adjustable items differ depending on the input signal. The items that cannot be adjusted or set do not appear in the menu. (1 page 69) Adjustment menu To clear the menu Press MENU. To reset the picture that has been adjusted Select Reset from Picture menu. Next menu window Setting items When the screen display appears, select Yes using < and press. All of the following settings are reset to its factory preset value. The settings of Reality Creation, Cinema Black Pro, Motionflow, Contrast, Brightness, Color, Hue, Color Temp., Sharpness and Expert Setting on the Picture menu 32

33 To reset the items that have been adjusted Select an item in the Menu screen, and display the pop-up menu, the setting menu, and the adjustment menu. Press RESET on the remote control to reset only the selected settings to its factory preset value. Note The RESET button on the remote control is available only when the adjustment menu or the setting menu is selected. Using the Menus 33

34 Picture Menu The Picture menu is used for adjusting the picture. Note These items may not be available, depending on the type of input signal. For details, see Input Signals and Adjustable/Setting Items (1 page 69). Item names in brackets represent those printed on the remote control. Calib. Preset [CALIBRATED PRESET] Reset 34 You can select the picture viewing mode that best suits the type of video source or the environment. You can save and use different preset modes for 2D/3D respectively. Cinema Film 1: Picture quality suited to reproducing the highly dynamic and clear images typical of master positive film. Cinema Film 2: Picture quality suited to reproducing the rich tone and color typical of a movie theater. Reference: A picture quality setup suitable for when you want to reproduce faithfully the original image quality, or for enjoying image quality, without any adjustment. TV: Picture quality suited for watching TV programs, sports, concerts, etc. Photo: Ideal for projecting still images taken with a digital camera. Game: Picture quality suited to gaming, with well-modulated colors and fast response. Bright Cinema: Picture quality suited for watching movies in a bright environment, such as a living room. Bright TV: Picture quality suited for watching TV programs, sports, concerts, and other video images in a bright environment, such as a living room. User: You can adjust the picture quality to suit your taste, and save the setting. The factory default setting is the same as Reference. Tip Any adjustments to picture quality settings are saved for each input. Resets all currently selected Calib. Preset mode settings to their default values (1 page 32). Tip Reset does not affect settings saved for the Custom 1 to 5 items of Color Temp. To reset Gain or Bias in Custom 1 to 5, use the RESET button on the remote control on the Gain or Bias setting screen.

35 Reality Creation [REALITY CREATION] Cinema Black Pro Adjusts the detail and noise processing of images. (Super-resolution function) On: Applies detail and noise processing effects. Resolution: When you increase the setting value, the texture and detail of the picture become sharper. Noise Filtering: When you increase the setting value, the noise (picture roughness) becomes less prominent. Test: On/Off: Changes On and Off at a certain frequency to check the effect of Reality Creation. Tip The display position of status during the test works together with the Menu Position (1 page 42) setting. Off: The Reality Creation function is not applied. Advanced Iris [ADVANCED IRIS] Switches the iris function. Auto Full: Automatically adjusts to optimize the iris aperture according to the brightness level of the input source. Moreover, signal processing, which optimizes gradation expression between the peak light and dark parts, expresses a large dynamic range. This results in a bright and high contrast image. Auto Limited: A lower brightness than Auto Full, making the image suitable for viewing in a dark room. Manual: Manually (fixed) adjusts the iris. Using the Menus Motionflow Off: Disables the iris (aperture) function. Lamp Control Switches the lamp output. High: Increases the brightness, and projects brighter images. Low: Decreases the brightness, and enhances blacks by minimizing brightness. Tip Setting Low reduces fan noise, while also reducing energy consumption for longer lamp life. Film Projection Reproduces an image similar to that of projected film. Use this setting as preferred, based on the image content. On: Reduces afterimage. Off: The reduction effect of afterimage is less than the On setting. The picture will become brighter. Motion Enhancer [MOTION ENHANCER] Reproduces fast-moving pictures smoothly without generating afterimages. High: Select this for picture quality smoother than Low. Low: Select this for smooth picture quality. Off: Select this to not apply the motion enhancer function. Tip Certain scenes may contain digital signal artifacts. In this case, set this function to Off. 35

36 Contrast [CONTRAST] Brightness [BRIGHTNESS] Color Hue Color Temp. [COLOR TEMP] Sharpness [SHARPNESS] Adjusts the contrast. Higher values increase the sharpness in images, while lower values decrease the sharpness. You can make adjustments by pressing the CONTRAST +/ on the remote control. Adjusts the brightness of the picture. The higher the setting, the brighter the picture. The lower the setting, the darker the picture. You can make adjustments by pressing the BRIGHTNESS +/ on the remote control. Adjusts the color density. The higher the setting, the greater the intensity. The lower the setting, the lower the intensity. Adjusts the color tone. The higher the setting, the more greenish the picture becomes. The lower the setting, the more reddish the picture becomes. Adjusts the color temperature. D93: Equivalent to 9,300 K color temperature normally used in TVs. Gives white colors a blue tint. D75: Equivalent to 7,500 K color temperature used as an ancillary standard illuminant. Gives a neutral tint between D93 and D65. D65: Equivalent to 6,500 K color temperature used as a standard illuminant. Gives white colors a red tint. D55: Equivalent to 5,500 K color temperature used as an ancillary standard illuminant. Gives white colors an even redder tint. Custom 1 to 5: Enables you to adjust, set, and store your favorite color temperature. You can adjust Gain and Bias of RGB. The factory default settings are as follows. Custom 1: Same as D93 color temperature setting. Custom 2: Same as D75 color temperature setting. Custom 3: Same as D65 color temperature setting. Custom 4: Same as D55 color temperature setting. Custom 5: Setting that prioritizes brightness. Sharpens the outline of the picture, or reduces the noise. The higher the setting, the sharper the picture. The lower the setting, the softer the picture, thus reducing the noise. You can make adjustments by pressing the SHARPNESS +/ on the remote control. 36

37 Expert Setting NR (Noise Reduction) Reduces the roughness or noise of the picture. Usually, use to select Off. If the picture is rough or noisy, select a setting from among Low, Middle or High according to the input signal source. MPEG NR (MPEG Noise Reduction) Reduces block noise and mosquito noise, in particular in digital signals. Usually, use to select Off. If the picture is rough or noisy, select a setting from among Low, Middle or High according to the input signal source. Film Mode According to the film source you have selected, make a setting for playback. Auto 1: Suitable for reproducing the original picture movement. Normally, set this to Auto 1. Auto 2: Reproduces a 2-3 or 2-2 Pull-Down format video signal, such as film sources, in a smooth picture movement. When a video signal other than 2-3 or 2-2 Pull-Down format is input, the picture is played back in progressive format. Off: Plays back the picture in progressive format without detecting video signals automatically. Contrast Enhancer Corrects the level of bright and dark parts automatically to optimize contrast according to a scene. Increases image sharpness and makes image dynamic. High/Middle/Low: You can adjust the contrast enhancer. Off: The contrast enhancer function is not applied. Gamma Correction [GAMMA CORRECTION] Adjusts the response characteristics of the tone of the picture. Select a favorite tone from 10 options. 1.8: Bright Produces a brighter picture overall : Dark Produces a darker picture overall. Gamma 7: Simulates the gamma curve of film. Gamma 8: Increases the sharpness in images. Select this when you watch in a bright environment, such as a living room. Gamma 9: Produces a brighter picture than Gamma 8. Gamma 10: Increases the sharpness in images. Select this when you watch TV programs, etc., in a bright environment, such as a living room. Off: Gamma Correction is not applied. Using the specified controller, ImageDirector3 (1 page 27) allows you to adjust, set, and store a favorite tone in a computer. For details on how to use ImageDirector3, refer to the Help in ImageDirector3. Using the Menus 37

38 Expert Setting x.v.color Set this item when playing back an x.v.color video signal. Set this item to On when connecting the unit with equipment that supports x.v.color and playing back an x.v.color video signal. For details on x.v.color, see About the x.v.color (1 page 53). Tip Setting x.v.color to On disables gamma adjustment. Color Space [COLOR SPACE] Converts the color space. BT.709: An ITU-R BT.709 color space, which is used for highdefinition television broadcast or Blu-ray Disc. The color space is equivalent to srgb. Color Space 1: The color space suited for watching TV programs and video images, such as sport, concerts, etc. Color Space 2: The color space suited for watching TV programs, sport, concerts, and other video images in a bright environment, such as a living room. Color Space 3: The color space suited for watching movies. 38

39 Advanced Picture Menu The Advanced Picture is used for adjusting the picture more. Using the Menus RCP (Real Color Processing) You can adjust the color, hue, and brightness of each selected portion of the picture independently. User 1, User 2, User 3: You can adjust the picture using Real Color Processing and store the settings. Once the settings are stored, you can view the picture with the adjusted picture quality. Off: Cancels this feature. For details, see Adjusting the Picture Using Real Color Processing. (1 page 29) 39

40 Screen Menu The Screen menu is used to adjust the input signal. You can adjust the size of the picture, and select aspect mode, etc.. Note These items may not be available, depending on the type of input signal. For details, see Input Signals and Adjustable/Setting Items (1 page 69). Item names in brackets represent those printed on the remote control. Aspect [ASPECT] Sets the aspect ratio of the picture to be displayed for the current input signal. (1 page 19) Wide Zoom: A 4:3 aspect ratio picture is projected naturally to fill the screen. The upper and lower portions of the picture are cropped. Zoom: A 4:3 aspect ratio picture is enlarged vertically and horizontally in the same ratio to fill the screen. The upper and lower portions are cropped. This mode is suitable to view a letterbox picture. If a movie subtitle, etc., at the bottom of the picture cannot be seen, it can be displayed by adjusting Vertical Size or V Center. (1 page 41) Normal: Displays a picture on the whole of the screen, maintaining the aspect ratio of the input picture. This is suitable for 16:9 or 4:3 pictures. Stretch: A picture squeezed to 4:3 is displayed in 16:9 aspect ratio. V Stretch: A 2.35:1 picture is displayed after having been changed to 16:9. This is the most suitable mode when using a commercially available anamorphic lens. Squeeze: Displays in its original aspect ratio when a 16:9 or 4:3 picture is viewed using a commercially available anamorphic lens. Full: Displays an original picture on the whole of the screen. Only when a computer signal is input. Notes When a computer signal is input, you can only select Normal and Full. When the input is a 3D signal or when 2D-3D Display Sel. in the Function menu is set to 3D, you can only select Normal or Squeeze. 40

41 Over Scan Screen Area V Center Vertical Size Adjust Signal Hides the edges of the picture. On: The edges of the input picture are not displayed. Select this setting when noise appears along the edge of the picture. Off: Projects the whole of the input picture. Tip To display the displayable region within the four directions of the screen, refer to Blanking on the Installation menu (1 page 48). Selects the size of the picture when a Hi-Vision picture is overscanned. Full: Expands the picture on the whole of the screen. Through: Does not expand the picture on the whole of the screen. Adjust the whole picture by moving up and down on the screen. As the selected number increases, the screen moves up, and as the selected number decreases, the screen moves down. Reduces or enlarges the picture vertically. The screen is enlarged as the setting increases and reduced as the setting decreases. If the subtitle of a movie, etc. cannot be seen, use this together with V Center. You can adjust the input signal. APA: Adjusts Phase, Pitch, and Shift automatically to a position that suits the image signal for pictures from a computer. Phase: Adjusts the dot phase and the phase of computer signal of pictures from a computer. Adjusts the picture to the point where it looks clearest. Pitch: Adjusts the horizontal size of the picture from a computer. As the number increases, the picture becomes wider, and as the number decreases, the picture becomes narrower. Adjust the setting to match the number of dots of the input signal. Shift: Adjusts the position of the picture. H: As the setting for H (horizontal) increases, the picture moves to the right, and as the setting decreases, the picture moves to the left. Use < /, to adjust the horizontal position. V: As the setting for V (vertical) increases, the picture moves up, and as the setting decreases, the picture moves down. Use M / m to adjust the vertical position. Using the Menus 41

42 Setup Menu The Setup menu is used to change the factory preset settings, etc. Status Language Menu Position Cooling Setting Standby Mode Sets whether or not the on-screen display is displayed. Set to Off to turn off the on-screen displays except for certain menus, message when turning off the power, and warning messages. Selects the language used in the menu and on-screen displays. You can change the position to display the menu on the upper screen. Bottom Left: Displays the menu on the bottom left area of the screen. Center: Displays the menu on the center of the screen. Use this item when using the projector at high altitudes. High: Use this setting when using the projector at an altitude of 1,500 m (approx. 4,900 ft) or higher. Standard: Use this setting when using the projector at normal altitudes. Note When this item is set to High, the fan noise becomes slightly louder since the number of fan rotations increase. Lowers the power consumption in standby. When set to Standard, the power consumption in standby becomes normal. When set to Low, the power consumption in standby is lowered. Note When this item is set to Low, the PJ Auto Power On function is disabled (The function is set to Off and does not appear in the menu.). (1 page 45) 42

43 Power Saving Lamp Setting Sets the power saving mode. Lamp Cutoff: The lamp turns off automatically and power consumption is reduced if no signal is input for 10 minutes. If signal is resumed, or any button on the control panel or remote control is pressed, the lamp will light again. In Lamp Cutoff, the ON/STANDBY indicator lights in orange. (1 page 4) Standby: The power will be turned off automatically and the projector goes to Standby mode if no signal is input for 10 minutes. Off: The Power Saving mode is released. When replacing the lamps, set the desired lamp setting. (1 page 62) Using the Menus 43

44 Function Menu The Function menu is used for changing the settings of the various functions of the projector. The 3D Settings menu can be displayed by pressing the 3D button on the remote control. 3D Settings You can change the settings of the 3D function. 2D-3D Display Sel.: For Switching the video images to 2D or 3D. Auto: Displays 3D video images when HDMI signals with 3D information are input. Displays 2D video images when other signals are input. 3D: Displays 3D video images according to the 3D system selected in 3D Format. However, when HDMI signals with 3D information are input the projector, displays 3D video images according to the 3D system of the HDMI signals with 3D information. 2D: Displays 2D video images. * The 3D information is additional information to discriminate 3D. Some HDMI signals have additional information to discriminate 3D and some HDMI signals have none. 3D Format: You can select this item by pressing b on the remote control when setting 2D-3D Display Sel. to 3D. Set the 3D system when the input HDMI signals do not include 3D information. Simulated 3D: Converts 2D video images to 3D video images. The setting can be made only for input the HD signals. The simulated 3D feature may have limited effect, depending on the video source. There are differences in perception of 3D video images among individuals. Side-by-Side: Displays 3D images as received (before conversion to sequential) in left-right split-screen format. Over-Under: Displays 3D images as received (before conversion to sequential) in top-bottom split-screen format. 44

45 3D Settings 3D Glasses Bri ness: For adjusting the brightness of the picture when watching 3D video images using the 3D glasses. You can select the brightness from among Min, 1, 2, 3, and Max. 3D Depth Adjust: For adjusting the depth of the 3D video images on the screen. The setting can be made only when a 3D Format other than Simulated 3D is selected. 3D SYNC Output HDMI Setting We recommended that 3D Depth Adjust be set to 0. The 3D video images may be difficult to perceive, depending on the setting of 3D Depth Adjust. Simulated 3D Effect: For adjusting the 3D effect when 2D content is converted to 3D video images. You can select the effect from among High, Middle, and Low. Notes The menu display has a ghost while a 3D video image is displayed and is best viewed with the 3D glasses. We recommended that the screen size be 100 to 120 inches. If you watch 3D video images on a screen larger than 120 inches, the 3D effect may be diminished. Switches the output of the 3D SYNC connector. Standard: This output is suitable for the built-in 3D Sync Transmitter and external 3D Sync Transmitter TMR-PJ2 (not supplied). This mode is the default setting. Option: Select this mode when connecting a transmitter other than TMR-PJ2. Note When you select Option, use the conversion cable. The availability of compatible transmitters varies, depending on the country/region. You can change the settings of the Control for HDMI function. Control for HDMI: Selects the function whether to turn the Control for HDMI function effective when the HDMI 1 and HDMI 2 connectors are connected to a Control for HDMI compatible equipment. When set to On, the following are available. The operation of the projector and the connected Control for HDMI compatible equipment will synchronize with each other. The Control for HDMI setting of Sony equipment (AV amplifier, video, etc.), which is compatible with Control for HDMI - Easy Setting *, will also be effective. Device Auto Power Off: Sets whether to also turn the power of the connected Control for HDMI compatible equipment off when you turn the power of the projector off. When set to On, the equipment will synchronize and turn off when the power of the projector turns. PJ Auto Power On: Select whether to link the power of the projector to the Control for HDMI compatible equipment. When set to On, the power of the projector will automatically turn on when the power of the connected equipment is turned on or when making operations such as playback. Using the Menus 45

46 HDMI Setting Note To enable this function, set Standby Mode (1 page 42) in the Setup menu to Standard, and then set PJ Auto Power On to On. For details, see About the Control for HDMI (1 page 52). Device List: Lists all the Control for HDMI compatible equipment connected to the projector. When Enable is selected, the Control for HDMI setting of Sony equipment (AV amplifier, video, etc.), which is compatible with Control for HDMI - Easy Setting, will also be effective. HDMI Dynamic Range Auto Input Search 46 * Control for HDMI - Easy Setting is a function that makes the Control for HDMI setting of equipment connected to HDMI input of the projector effective as well when the Control for HDMI setting of the projector is effective. This function is only available between compatible Sony equipment, and some equipment may not be compatible. Although some non-sony equipment may be compatible, operation is not guaranteed for such equipment. Set the video input level of HDMI 1 and HDMI 2 connectors. Auto: Sets the video input level automatically. Limited: The video input level is set for signals of Full: The video input level is set for signals of Note If the video output setting of the connected HDMI device is not set correctly, light and dark parts of the video may appear too light or too dark. Hides input terminals that do not have signal input. When set to On, terminals without input signals do not appear on the input palette that appears when you press INPUT. To display all input terminals, set this to Off. (1 page 17) Background Selects the background color of the screen when no signal is input. You can select Black or Blue. Settings Lock Locks menu item settings to prevent operational error. (1 page 47) Off: Cancels the Settings Lock. Level A: Clears the display of 20 items from the menu. Level B: In addition to Level A, clears the display of a further 16 items.