3M High-Speed Solutions
|
|
- Frederick Booth
- 6 years ago
- Views:
Transcription
1 3M High-Speed Solutions 3M All Rights Reserved.
2 Distance 3M Electronic Solutions Division 3M Twin Axial and AOC Solutions Addressing Physical Medium Dependent in the InifiniBand Fabric 100m 10m 1m Optical KEY FACTORS Length Power Size/weight EMI Cost Copper 10G 20G 30G 40G Speed/channel 2
3 3M High-Speed I/O Objectives Extend life of copper based high-speed interconnects Close the cost gap between fiber optics and copper technologies Leverage 3M s technologies and process capabilities to enable these objectives 3 3M All Rights Reserved.
4 3M Innovation Model Technology Platforms Abrasives Adhesives Ceramics Electronics, Software Films Microreplication Nanotechnology Non-wovens Precision Coating Vapor Processing Opportunity Drives Development and Utilization Markets Architecture & Construction Consumer & Office Display Electronics Filtration Health Care Renewable Energy Safety & Security Telecoms and Utilities Water Infrastructure The Variety of Things 3M Can Do 4
5 3M Twin Axial Cable * 5
6 Core Twin Axial Cable Platform 6
7 Key Innovation #1: Longitudinal vs. Spiral Wrapped Shield CONTINUOUS Shield Homogeneous in both Transverse and Longitudinal Directions C C Periodic Electrical Discontinuities L L 3M Twin Axial Cable vs. Conventional Twin Axial Cable Benefits Minimizes Insertion Loss Reduces radiated EMI 7
8 Insertion Loss (db) 3M Electronic Solutions Division Result is High-Performance and Resonance-Free Example below 0-5 3M Twin Axial Cable SL Standard spiral wrapped shields exhibit LC notch filter resonance Standard spiral wrapped Cable L C L C High loss resonance Frequency (MHz)
9 Open Eyes to 25 Gbps Without Active Equalization 10 Gb/s 15 Gb/s Eye Height = 62.1 mv, Jitter = 9.4 ps (0.09 UI) Eye Height = 50.8 mv, Jitter = 8.9 ps (0.13 UI) 20 Gb/s 25 Gb/s Eye Height = 39.5 mv, Jitter = 9.8 ps (0.20 UI) Eye Height = 30.5 mv, Jitter = 11.1 ps (0.28 UI) 9 1 meter sample, Ag plated 30 AWG
10 CMPT (db) 3M Electronic Solutions Division Exceeds EMI Requirement without Added Shield Typical based on >10 samples 0 CMPT Unjacketed (Internal) Twinax Cable Frequency (MHz) CMPT Limit for Twinax Cable Competitor X Competitor Y 3M
11 3M All Rights Reserved. 3M Electronic Solutions Division Cable termination is consistent, reliable and cost effective. STEPS Cut Strip the dielectric Strip the shield BENEFITS No wire management fixtures required Simultaneous stripping of four pairs After stripping, cable lays directly on PCB pattern Fixed position of wire distribution allows easy automation Apply to paddle card and solder For more details go to Select Product Information then open Twin Axial Cable Preparation under the Instructions section. 11
12 Products Leveraging 3M Twin Axial Cable Technology External I/O Applications 10G SFP+ Assemblies 40G/56G QSFP+ Assemblies 4x6G external minisas Assemblies (26p) 12 Waferized 10/25 Gbps Backplane Assemblies (In development) HDMI Assemblies (In development)
13 Products Leveraging 3M Twin Axial Cable Technology In-the-box Applications 3M Twin Axial Cable 3M Cable Assemblies for PCIexpress Applications (CPU to CPU/GPU) 3M SATA Assemblies (CPU to HDD) 3M High Routability minisas Assemblies (36p, 68p) (CPU to HDD) 13 3M SATA and minisas Fanout Assemblies (CPU to HDD)
14 3M High-Speed Copper Interconnect Roadmap 3G/6G Per Ch. 8G/10G Per Ch. 14G Per Ch. 25G Per Ch. Products 25 G B2B Connector 25 G Backplane 3M Twin Axial Ribbon Cable Platform 0.8mm, 15 G Cable-to-Board 25 G Cable Assembly Customer Benefit Price/Performance Benefit Increased I/O Density EMI Control Extends Life of Cu Infrastructure i.e. Lower Total System Cost Enabling Technologies Precision Formed Shield Low k Dielectric Process And Materials Green Jacketing Materials EMI Absorbing Materials Controlled Impedance Design 14 Product roadmap driven by target account roadmaps and high value technology 3M All Rights Reserved.
15 Distance 3M Electronic Solutions Division 3M Twin Axial and AOC Solutions Addressing Physical Medium Dependent in the InifiniBand Fabric 100m 10m 1m Optical KEY FACTORS Length Power Size/weight EMI Cost Copper 10G 20G 30G 40G Speed/channel 15
16 3M s Fiber technology background 16
17 3M Fiber optic connectors and Terminations 17
18 Volition VF-45 Small-Form Factor Connector 18
19 AOC Development Challenge Customers want Lower cost Lower power Increased density Customers Need Solutions that Extend beyond the range of copper solutions A fair cost trade-off for price & performance Readily scalable solution to support roadmap 19
20 Light Engine traditional approach 20
21 3M s Light Engine Leveraging 3M Technologies & Processes Precision Molding Thermal Management Adhesives Laser Machining Coatings Micro-optics Abrasives 21
22 3M Active Optical Cable (AOC) Assemblies CX4 AOC (SFF8470) 20 Gbps Low Power Available Q4-11 CXP AOC (SFF8642) 120 Gbps 40G/56G QSFP+ Assemblies Anticipated Q2-12 Delivering Exceptional Cost / Performance 22 3M 2011 All Rights Reserved.
23 Key Innovation #1: Scalable Low Power Optical Engine Designed for high-density and low-cost Can be used in both AOCs and on-board module designs Low power per end 660 mw Passive alignment 23
24 Fiber 2. Alignment region 3. Adhesive trench 4. Mirror surface 5. Lens 3M Electronic Solutions Division Optical Interconnect Roadmap 3G/6G Per Ch. 10G/14G Per Ch. 25G Per Ch. 50G Per Ch. Expanded Beam Cross Section Products Active Optical Cable Assembly Platform Optical Backplane components Waveguides on Board Chip to Chip Optical Interconnect Mixed Cu/Optical Interconnect Business Benefit Price/Performance Benefit Lower System Power Consumption Increased I/O Density Enabling Technologies Firmware/ Electronics Precision V-grooves/moldings Adhesives/ Abrasives Thermal Management Coatings Laser Machining Micro-optics/processes 24 Product roadmap driven by target account roadmap and high value technology 3M All Rights Reserved.
25 Distance 3M Electronic Solutions Division 3M Twin Axial and AOC Solutions Addressing Physical Medium Dependent in the InifiniBand Fabric 100m 10m 1m Optical KEY FACTORS Length Power Size/weight EMI Cost Copper 10G 20G 30G 40G Speed/channel 25
26 Thank You! 26 3M All Rights Reserved.
27 3M is a trademark of 3M Company. Important Notice The information we are furnishing you is being provided free of charge and is based on tests performed at internal 3M laboratory facilities. While we believe that these test results are reliable, their accuracy or completeness is not guaranteed. Your results may vary due to differences in test types and conditions. This information is intended for use by persons with the knowledge and technical skills to analyze, handle and use such information. You must evaluate and determine whether the product is suitable for your intended application. The foregoing information is provided AS-IS. In providing this information makes no warranties regarding product use or performance, including any implied warranty of merchantability or fitness for a particular use Warranty; Limited Remedy; Limited Liability.. 3M s product warranty is stated in its Product Literature available upon request. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. 27
3M Locator Plate N
M Locator Plate 44-107N Instructions for the assembly of.100 x.100 preassembled socket connectors 1.0 General The M Locator Plate 44-107N is designed to aid in the assembly of the preassembled socket connector
More informationInstruction Guide February 2017
Instruction Guide February 2017 3M Instruction Guide: 3M TM Locator Plate 3443-81-XX, 3D-Printed Instructions for the assembly of 3M TM Ribbon Cable Wiremount Socket Assembly, 451 Series 1.0 General 1.1
More information3M Coupling Tray FDTC-10S-COUPLINGTRAY
3M Coupling Tray FDTC-10S-COUPLINGTRAY for use with 3M Fiber Dome Closures FDC 10S Instructions July 2010 3 1.0 Introduction The 3M Coupling Tray FDTC-10S-COUPLINGTRAY can accommodate up to 10 loose tubes.
More informationSolutions for Electronic Specialty Markets (ESM)
3M Worldwide : United States : Electronics Manufacturing Solutions for Electronic Specialty Markets (ESM) Product Catalog for Electronic Specialty Markets 3M Electronic Specialty Markets - New Product
More information3M SLiC 530/533/733-2 Port 0.61 Cable Entry Bracket 3M SLiC 530/533/733-2 Port-MSM 0.61 Cable Entry Bracket
3M SLiC 530/533/733-2 Port 0.61 Cable Entry Bracket 3M SLiC 530/533/733-2 Port-MSM 0.61 Cable Entry Bracket For use with 3M SLiC Free-Breathing Fiber Optic Closures and Terminals Instructions November
More information3M TM Twin Axial Cable Assemblies
3M TM Twin Axial Cable Assemblies Electronics Materials Solutions Division 2017 11/9/2017 3M. All Rights Reserved. Our Vision 3M Technology Advancing Every Company 3M Products Enhancing Every Home 3M Innovation
More information3M 8900 Single-mode SC Crimplok Connector
3M 8900 Single-mode SC Crimplok Connector Technical Report June 1999 80-6110-1441-8 1 1.0 Product Description & Requirements The 3M SC Single-mode Crimplok Connector is designed to provide the customer
More information3M No Polish Jacketed SC/APC Connector
Communication Markets Division 3M No Polish Jacketed SC/APC Connector For use with 1.6 to 3.0 mm Jacketed Cable 3M No Polish SC/APC Connector enables fast, on-site termination of 1.6 mm to 3.0 mm jacketed
More information3M Cold Shrink Foldback Splice Jacket Kit
3M Cold Shrink Foldback Splice Jacket Kit SJ-FB Instructions! CAUTION Working around energized systems may cause serious injury or death. Installation should be performed by personnel familiar with good
More information3M Sensored Termination (15 kv) QX-T15I-vi1-E
3M Sensored Termination () QX-T15I-vi1-E Data Sheet May 2016 Kit Contents: Each kit contains sufficient quantities of the following materials to make three single-phase terminations. 31" (REF) One piece
More information3M Cold Shrink Splice Kit QS-III 5514A
3M Cold Shrink Splice Kit QS-III 5514A for UniShield, Wire Shielded, Longitudinally Corrugated (LC), and Tape Shielded (Ribbon Shielded) Cable or Transitions to Concentric Neutral (CN)/Jacketed Concentric
More information3M Fiber Optic Splice Tray 2527 with 3M PLC Optical Splitter
3M Fiber Optic Splice Tray 2527 with 3M PLC Optical Splitter Instructions January 2010 3 1.0 General 1.1 The 3M Fiber Optic Splice Tray 2527 with 3M PLC Optical Splitter(s) protects, organizes and stores
More information3M Cold Shrink QS4 Integrated Splice Kit QS4-35TS
3M Cold Shrink QS4 Integrated Splice Kit QS4-35TS-350-1000 for Tape Shield, Wire Shield, UniShield, and Longitudinally Corrugated (LC) Cable Instructions IEEE Std. 404 35 kv Class 250 kv BIL F CAUTION
More information3M No Polish Jacketed SC/APC Connector
Communication Markets Division 3M No Polish Jacketed SC/APC Connector For use with 1.6 to 3.0 mm Jacketed Cable 3M No Polish SC/APC Connector enables fast, on-site termination of 1.6 mm to 3.0 mm jacketed
More information3M Cold Shrink Splice Kit QS-III 5515A
3M Cold Shrink Splice Kit QS-III 5515A for UniShield, Wire Shielded, Longitudinally Corrugated (LC), and Tape Shielded (Ribbon Shielded) Cable or Transitions to Concentric Neutral (CN)/Jacketed Concentric
More informationSLiC Fiber Aerial Closure System
3 SLiC Fiber Aerial Closure System SLFC 533-SP SLFC 533-TS SLFC 733-SP Instructions May 2005 78-8135-4502-3-B N C H E S R A N G E M IL L IM E T E R S.4 10.6.8 A B C 15 20 I 1.0 Kit Contents Note: Examine
More informationInstructions. Cable with Armor F CAUTION. October Rev A
3M Single Conductor Accessory Breakout Kits (BOK's) for use with 3M Cable Accessories (Terminations, T-Bodies and Push-On Elbows) For Use With Single Conductor Accessories On Three-Core Conductor Cables
More information3M Fiber Optic Splice Closure 2178-XSB/XSB-FR & 2178-XLB/XLB-FR 3M Cable Addition Kit 2181-XB/XB-FR
3M Fiber Optic Splice Closure 2178-XSB/XSB-FR & 2178-XLB/XLB-FR 3M Cable Addition Kit 2181-XB/XB-FR Instructions July 2010 78-8135-0094-5-K 3 1.0 General 1.1 3M Fiber Optic Splice Closure 2178-XSB The
More informationCold Shrink Three-Conductor Splice Kit QS-III for use on Armor and Non-Armor Cables Instructions IEEE Std kv Class 250 kv BIL
Cold Shrink Three-Conductor Splice Kit QS-III for use on Armor and Non-Armor Cables Instructions IEEE Std. 404 35 kv Class 250 kv BIL Kit Number 5798A-MT Cable Range Requirements Cable Insulation O.D.
More information18mm ECAM Cable Entry Port
18mm ECAM Cable Entry Port Instructions October 2006 1.0 Introduction The 3M 18mm ECAM (External Cable Assembly Module) Cable Entry Port Kit is designed to accept fiber optic cables with external diameters
More information3M Scotchcast Mine and Portable Cable Splice and Jacket Repair Kit M-40
3M Scotchcast Mine and Portable Cable Splice and Jacket Repair Kit M-40 Instructions 1 & 2 For Jacket Repair (pages 2 & 7) Supplemental Instructions for: Insulation Repair (page 12) Conductor Repair (page
More information3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR
3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR 3M Cable Addition Kit 2181-XL and 2181-XL/FR Instructions September 2017 78-8130-5055-2-M 2 September 2017 78-8130-5055-2-M 1.0 Kit Contents 2.0 General...
More information3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR 3M Cable Addition Kit 2181-XL and 2181-XL/FR
3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR 3M Cable Addition Kit 2181-XL and 2181-XL/FR Instructions July 2010 3 1.0 Contents 1.0 General...3 2.0 Kit Contents...3 3.0 Cable Preparation...4 4.0
More information3 SLiC Aerial Closure with Rubber End Seal
3 Aerial Closure with Rubber End Seal Instructions 1.0 General 1.1 This instruction bulletin describes the assembly of the 3M Aerial Closure with external bonding hanger brackets. These closures are suitable
More information3M Scotchcast Flexible Power Cable Splice Kits 82-F Series
3M Scotchcast Flexible Power Cable Splice Kits 82-F Series For use in weather-exposed, direct burial or submerged locations. For making in-line splices on non-shielded portable power cables and cords rated
More information3M Cold Shrink QS-III Silicone Rubber Splice Kit 5488A-TOW/WOT
3M Cold Shrink QS-III Silicone Rubber Splice Kit 5488A-TOW/WOT For Tape Over Wire (TOW) and Wire-Over-Tape (WOT) Shielded Cable For 250 2000 kcmil cable with 650-mil primary insulation thickness Instructions
More information2179-CD Series Fiber Optic Splice Closure. Installation Instructions
2179-CD Series Fiber Optic Splice Closure Installation Instructions 1.0 Product Introduction The new 3M TM 2179-CD Series Fiber Optic Splice Closure can be used in buried, underground, aerial, and pedestal
More information3M Distribution Box (DDB)
3M Distribution Box (DDB) Merged Copper and Fiber Pole/Post Mount Enclosure Installation Instructions November 2015 78-0015-2736-1-A 2 November 2015 78-0015-2736-1-A Contents 1.0 General 2.0 Enclosure
More information3M Pak 10 Socket 1 mm Straight and Right Angle, Surface Mount PK10 Series
1 mm pitch connector system Stacked, Horizontal or Vertical Mating Low profile 5 mm mated height Surface mount retention clips reduce stress on surface mount leads Keyed design helps prevent mating misalignment
More informationHigh Density Block BRCP. HD BRCP- 128/192/256 pair. Installation Instructions
High Density Block BRCP HD BRCP- 128/192/256 pair Installation Instructions Product Introduction The BRCP block is the latest generation of MDF terminal blocks developed by 3M, specifically designed for
More information3M Motor Lead Inline Splice 5331, 5332, 5333 & 5334
3M Motor Lead Inline Splice 5331, 5332, 5333 & 5334 for 5/8 kv Non-Shielded and Shielded Cables (Ribbon, Wire and UniShield Cables) Instructions Cable Size Range: Feeder: #8 AWG 500 kcmil Motor Lead: #10
More information3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN-4/0-500
3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN-4/0-500 for Jacketed Concentric Neutral (JCN) and Flat Strap Neutral Cable Instructions IEEE Std. 404 15 kv Class 150 kv BIL CAUTION Working around energized
More information3M Mini D Ribbon (MDR) Cable Assembly
3M Mini D Ribbon (MDR) Cable Assembly.050 Digital Camera Extension Cable 26 position 1WL26-TZ3B-XXX-03C Mates to popular 3M MDR 26 position receptacle on one end, and to another MDR 26 position cable assembly
More information3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN
3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN-500-1000 for Jacketed Concentric Neutral (JCN) and Flat Strap Neutral Cable Instructions IEEE Std. 404 15 kv Class 150 kv BIL F CAUTION Working around
More informationUltra-Low Power Optical Links in Portable Consumer Devices
Ultra-Low Power Optical Links in Portable Consumer Devices Holger Hoeltke Silicon Line GmbH 1 Legal Disclaimer The material contained herein is not a license, either expressly or impliedly, to any IPR
More information3M Slim Lock Closures
3M Health Care 3M Slim Lock Closures 3M Tower Weatherproofing Solutions Sesh Natarajan 3M Health Care 3M Tower Weatherproofing Solutions Market trend towards denser RF connectors on tower equipment Macro
More information3M Cold Shrink Splice Kit QS-III 5416A
3M Cold Shrink Splice Kit QS-III 5416A for Jacketed Concentric Neutral (JCN) and Concentric Neutral Cable Instructions IEEE Std. 404 15 kv Class 150 kv BIL CAUTION Working around energized systems may
More information3M Fiber Optic Closure System LL
3M Fiber Optic Closure System LL 3M Fiber Optic Closure System The 3M Fiber Optic Closure System LL provides a protective yet accessible environment for housing single or mass fusion fiber splices. The
More information3M Scotchcast Reenterable Signal and Control Cable Splicing Kits 78-R Series
3M Scotchcast Reenterable Signal and Control Cable Splicing Kits 78-R Series Instructions Voltage Rating: 1000 V, Temperature Rating: 90 C Kit Contents 78-R1 78-R2 78-R3 78-R4 78-R5 Sleeve Set 1 1 1 1
More information3M Better Buried Closures
3M Better Buried Closures Instructions March 2016 78-0015-2945-8-A Contents: 1.0 General... 3 2.0 Kit Contents... 3 3.0 Closure Selection Guide... 4 4.0 LHS End Cap Installation... 5 5.0 Cable Preparations...
More informationCabinet Tools and Accessories Ordering Guide
3 Cabinet Tools and Accessories Ordering Guide 3M Cabinet Tools and Accessories 3M 4320 Block Spare Parts Replacement Cap Kit 100 Tan + 100 Orange 1/cs. 1/cs. 054007-63793 Half-tap, feed through 100 Tan
More informationNX Mini-SAS QSFP+ SFP+
High Bandwidth Innovative-Interconnect Solutions Design Through Manufacture of High-Performance-Interconnect Systems, Connectors & Cable Assemblies NX Mini-SAS QSFP+ SFP+ Command+Shift Click to Override
More information27mm ECAM Double Cable Entry Port
27mm ECAM Double Cable Entry Port Instructions October 2006 1.0 Introduction The 3M 27mm ECAM Double Cable (External Cable Assembly Module) Entry Port is designed to accept fiber optic loose tube & central
More information3M Fiber Optic Wall Mount Enclosure 8430 Series
3M Fiber Optic Wall Mount Enclosure 8430 Series Installation Instructions January 2014 3 78-0013-9429-1-A Table of Contents 1.0 Description...3 2.0 Parts...4 3.0 Assembly...4 4.0 Mounting the Enclosure...6
More information4320 SS-25 Self-Strip Terminating Block
4320 SS-25 Self-Strip Terminating Block Instructions May 2002 78-8130-7677-1 1.0 General The 3M 4320 SS-25 Self-Strip Terminating Block is a factory stubbed, self-stripping connecting block designed for
More informationScotch Heavy Duty Vinyl Electrical Tape 22
Scotch Heavy Duty Vinyl Electrical Tape 22 Data Sheet July 2015 Description Agency Approvals & Self Certifications Scotch Heavy Duty Vinyl Electrical Tape 22 is a premium grade, 10-mil thick, vinyl insulating
More information3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN-2-4/0
3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN-2-4/0 for Jacketed Concentric Neutral (JCN) and Flat Strap Neutral Cable Instructions IEEE Std. 404 15 kv Class 150 kv BIL F CAUTION Working around energized
More informationCrimplok. Connectors. 3M Crimplok ST* Connector Multimode 1. 3M Crimplok SC Connector Single-mode 2
3 Crimplok Connectors Quick, easy installation and superior performance To successfully design, install or operate today s fiber optic networks, you need components that offer speed and reliability from
More information3M We are Projectors! When the show must go on, 3M makes it easy:
3M Digital Projectors Digital Projector Family Brochure When the show must go on, 3M makes it easy: Whether it s a daily briefi ng, a classroom presentation, or your annual customer conference, you want
More informationSD/HD-SDI 1 to 2 Distribution Amplifier VCF-1002DA-P
User Manual SD/HD-SDI 1 to 2 Distribution Amplifier VCF-1002DA-P NOTE: The casing design is subject to change without notice. Our SD/HD/3G-SDI Distribution Amplifier is a 1 in, 2 out distribution and extender
More informationOptical Network for Uncompressed High Definition Video Transmission
Optical Network for Uncompressed High Definition Video Transmission Wenbin Jiang 3/25/2015 Outline Uncompressed HD video applications Hardware & network bandwidth for supporting HD video Bottleneck for
More informationScotchlok Connectors and Tools
Scotchlok Connectors and Tools Proven Solutions For Today s Applications A New Series of Tools and Connectors from 3M. Over 45 years ago, 3M introduced the industry s original insulation displacement connector
More information3M Automotive and Aerospace Solutions Division. Spec d to protect.
3M Automotive and Aerospace Solutions Division Spec d to protect. Every military mission is a critical mission. It takes training, precision and confidence. That s why your helicopter has to be in top-notch
More information3M Cold Shrink QS4 Integrated Splice Kit QS4-15SP-2-4/0
3M Cold Shrink QS4 Integrated Splice Kit QS4-15SP-2-4/0 for Jacketed Concentric Neutral (JCN), Flat Strap, Tape Shield and Longitudinally Corrugated (LC) Cable Instructions IEEE Std. 404 15 kv Class 150
More informationSLiC Fiber Aerial Closure 533 and 733
SLiC Fiber Aerial Closure 533 and 733 3M s SLiC fiber aerial closures are designed to enable service providers to costeffectively deploy aerial fiber networks in the access network (FTTN, HFC, and FTTP).
More information10Gbps SFP+ Optical Transceiver, 10km Reach
10Gbps SFP+ Optical Transceiver, 10km Reach Features Optical interface compliant to IEEE 802.3ae 10GBASE-LR Electrical interface compliant to SFF-8431 Hot Pluggable 1310nm DFB transmitter, PIN photo-detector
More information3 Foam Sealed Closure 2" (50 mm) with Compound Compression
3 Foam Sealed Closure 2" (50 mm) with Compound Compression Instructions 1.0 General 1.1 The 3M Foam Sealed Closure is designed to be used in the construction and maintenance of buried and underground PIC
More informationCold Shrink Silicone Rubber Termination QT-II
3 Cold Shrink Silicone Rubber Termination QT-II Instructions IEEE Std. No. 48-1990 Class 1 Termination 15 Class 110 kv BIL Kit Contents: 1 Hi-K Silicone Rubber Termination 2 Scotch Silicone Rubber Tape
More informationDynatel Advanced Cable Locator 2250
3 Dynatel Advanced Cable Locator 2250 Quickly and Accurately Identify Underground Assets Pinpoint exact cable path and depth quickly and easily with this lightweight, easy-to-handle unit The 3M Dynatel
More information3M Better Buried Closure (with 3M Scotchlok Shield Bond Connector 4462-FN and 3M High Gel Re-enterable Encapsulant 8882)
3M Better Buried Closure (with 3M Scotchlok Shield Bond Connector 4462FN and 3M High Gel Reenterable Encapsulant 8882) Instructions April 2016 78813509979C Contents: 1.0 General... 1 2.0 Kit Contents...
More informationF CAUTION. Jacketed Concentric Neutral (JCN) Cable. Concentric Neutral (CN) Cable. IEEE Std. No. 48 Class 1 Termination 15 kv Class 110 kv BIL
3M Cold Shrink QT-III Silicone Rubber Skirted Termination Kit With High-K Stress Relief 7642-S-2 For Jacketed Concentric Neutral (JCN) and Concentric Neutral (CN) Cable Instructions IEEE Std. No. 48 Class
More informationMini HD-SDI Optical Transceiver Model No : VCF-MF01TXRX
User Manual Mini HD-SDI Optical Transceiver Model No : VCF-MF01TXRX NOTE: The casing design is subject to change without notice. Our Mini SD/HD-SDI optical transceiver is a Ultra -mini and economical version
More informationUser Guide. HDMI Active Cable Extender. DVI-7370c
User Guide HDMI Active Cable Extender DVI-7370c TABLE OF CONTENTS SECTION PAGE PRODUCT SAFETY...1 PRODUCT LIABILITY STATEMENT........................ 1 1.0 INTRODUCTION...2 2.0 SPECIFICATIONS...3 3.0 PACKAGE
More informationHSK Mine and Portable Cable Splice
8096-4-HSK Mine and Portable Cable Splice Instructions 5 and 8 kv rated cables; Type SHD-GC Size 2/0 4/0 (connector max. length 2 1/2") 8096-4-HSK Mine and Portable Cable Splice 78-8119-6296-4-A 1 1.0
More information3M Cold Shrink Rubber Splicing Kit 5552
3M Cold Shrink Rubber Splicing Kit 5552 for 5/8 kv Shielded to Shielded or Shielded to Non-Shielded Cables Instructions IEEE Std. No. 404 5 kv Class, 75 kv BIL 8 kv Class, 95 kv BIL! CAUTION Working around
More information3M Cold Shrink QS-III Splice Kit 5467A(S)-WF
3M Cold Shrink QS-III Splice Kit 5467A(S)-WF for Jacketed Concentric Neutral (JCN) Cable Instructions IEEE Std. 404 35 kv Class 250 kv BIL F CAUTION Working around energized systems may cause serious injury
More information3M MetPak 2-FB Header
M MetPak 2-FB Header Solder Tail End-to-end stackable Select load capability Monoblockable Shoulder Pin Press Fit End-to-end stackable Early mate late break for hot swapping (press-fit EMLB adjusted by
More informationModel Extend HDMI audio and video connections up to 300 feet. Add up to 8 additional receivers with a dedicated network switch
HDMI Extender over Single CAT 6 Cable with IR Control Model 103002 Extend HDMI audio and video connections up to 300 feet Utilize existing Cat 6 wiring for an easy installation Add up to 8 additional receivers
More informationXW3D. Simple Wiring of Sensor Actuators. Connector Terminal Boxes. Specifications. Materials and Finish. Connection Combinations
Terminal Boxes XWD CSM_XWD_DS_E Simple Wiring of Sensor Actuators Greatly reduce wiring in combination with the Smartclick XS. Insert the connector and turn / of a turn to lock the connectors. Higher rated
More informationMX-MOLDED READY VGA TO BNC CABLES MX-2076 MX MDR Electronics
MX-MOLDED READY VGA TO BNC CABLES MX-2076 MX-2077 MDR Electronics www.mdrelectronics.com Table of contents 1. Introduction 3 2. Image 4 3. Features 6 4. Specifications 7 5. Warranty 8 http://www.mdrelectronics.com/
More informationBuilt tough for long-term connections
Communication Markets Division 3M Scotchlok Connectors Built tough for long-term connections 2 3 Durable, insulated connections on the first crimp. Over 50 years ago, 3M introduced the industry s original
More informationBuilt tough for long-term connections
Communication Markets Division 3M Scotchlok Connectors Built tough for long-term connections 2 3 Durable, insulated connections on the first crimp. Over 50 years ago, 3M introduced the industry s original
More information3M ScotchCode Wire Marking and Identification System. Identify with 3M
3M ScotchCode Wire Marking and Identification System Identify with 3M Dispensers 3M ScotchCode Wire Marker Tape Dispenser STD The 3M ScotchCode Wire Marker Tape Dispenser STD is a compact, carry-along
More informationSections 1. Application Equipment 2. Cable Preparation 3. Assembly 4. Termination Procedure 5. Inspection 6. Repair 7.
Page 1 of 6 Coaxial SolderSleeve Termination with Pre-Installed Wires or PCB Termination Body, B-044, B-043, B-041, B-040, B-020, B-021, B-046, D-148 Series Cable Type Typical RG Cable # -A- RG 178 RG
More informationElectrical Markets 3M ScotchCode Wire Marking and Identification System. Quality. Marking. For Most Projects
Electrical Markets 3M ScotchCode Wire Marking and Identification System Quality Marking For Most Projects Dispensers 3M ScotchCode Dispenser STD-TAG The proprietary 3M ScotchCode Dispenser STD-TAG simplifies
More informationFOSC-450D. Fiber Optic Splice Closure. 1 Introduction. Content. 5 Cable termination. 6 Fiber routing. 2 General. 7 Installation of the gel block
FOSC-450D I N S T A L L A T I O N I N S T R U C T I O N Fiber Optic Splice Closure Content 1 Introduction 2 General 2.1 Kit content 2.2 Tools 2.3 Accessories 2.4 Capacity 3 Preparation of the closure 4
More information3M Cubitron. II Fibre Disc 982C and 987C Now available in grades 36+, 60+ and 80+ Engineered. Perfection. Epic Performance.
3M Cubitron II Fibre Disc 982C and 987C Now available in grades, and Engineered Perfection. Epic Performance. The Future is Now. Leave conventional abrasives in the past and do more than you thought possible
More informationCommunication Markets Division. 3M Fiber Closures. Smart design makes your job easier.
Communication Markets Division 3M Fiber Closures Smart design makes your job easier. 2 Your connections deserve the best protection. No matter the size and configuration of your network, protecting its
More informationMX-MOLDED READY VGA CABLES MX-2074, 2075, 2079,(LOW AND MID) MX-2987,(HIGH END) MDR Electronics
MX-MOLDED READY VGA CABLES MX-2074, 2075, 2079,(LOW AND MID) MX-2987,(HIGH END) MDR Electronics www.mdrelectronics.com Table of contents 1. Introduction 3 2. Image 4 3. Features 6 4. Specifications 7 5.
More information3M Better Buried Compound Compression Closure System
3M Better Buried Compound Compression Closure System Instructions March 2016 78-0015-2948-2-A Contents: 1.0 General...3 2.0 Kit Contents...3 3.0 Closure Selection Guide...4 4.0 LHS End Cap Installation...5
More informationARIS EXPLORER 1200 GETTING STARTED
ARIS EXPLORER 1200 GETTING STARTED Table of Contents 1 INTRODUCTION 2 WHAT S IN THE BOX 3 HOOKING UP THE SONAR 4 ARIScope SOFTWARE 5 CAPTURING QUALITY IMAGES 6 COMPUTER REQUIREMENTS 7 WARRANTY INFORMATION
More informationQSFP+ 40GBASE-SR4 Fiber Transceiver
QSFP+ 40GBASE-SR4 Fiber Transceiver Preliminary Features RoHS-6 compliant High speed / high density: support up to 4X10 Gb/s bi-directional operation Compliant to industrial standard SFF-8436 QSFP+ standard
More informationTFT-150R-G. Tape Shield Cable (page 2) Suggested Installation Equipment (not supplied with kit) Wire Shield Cable (page 7)
TFT-150R-G 5-15kV Cold Applied Indoor (5-8kV Indoor and Outdoor) Termination for Copper Tape, Wire Shield, Lead Sheath, and UniShield Cable Suggested Installation Equipment (not supplied with kit) Cable
More information3M Cross-Connect Cabinets 4220SVB, 4220SVC and 4220SVE 3M Junction Box (JBOX)
3M Cross-Connect Cabinets 4220SVB, 4220SVC and 4220SVE 3M Junction Box (JBOX) In-cabinet and Outdoor AC Power Junction Box (JBOX) for 3M Cross-Connect Cabinets with DSLAM apparatus cases installed Instructions
More information3M One Pass Mini Fiber Pathway
3M One Pass Mini Fiber Pathway Executive Questions What is the 3M One Pass Mini Fiber Pathway? The 3M One Pass Mini Fiber Pathway is a flexible, single-fiber, surface-mount cable pathway and drop cable
More informationCommunication Markets Division 3M Scotchlok Connectors and Tools. Proven. Solutions for. Today s Applications
Communication Markets Division 3M Scotchlok Connectors and Tools Proven Solutions for Today s Applications A Proven Series of Tools and Connectors from 3M. 50 years ago, 3M introduced the industry s original
More information2178-L/S Series Fiber Optic Splice Case with Gasket
2178-L/S Series Fiber Optic Splice Case with Gasket Instructions for: 2178-S Splice Case 2178-LS Splice Case 2178-LL Splice Case 2181-LS Cable Addition Kit May 1997 34-7041-9949-5-A 1 Table of Contents
More informationDATA CENTER OPTICAL ASSEMBLIES TO SUPPORT QSFP, CFP AND CXP INDUSTRY STANDARD PINOUT CONFIGURATIONS
DATA CENTER OPTICAL ASSEMBLIES TO SUPPORT QSFP, CFP AND CXP INDUSTRY STANDARD PINOUT CONFIGURATIONS Data Center Optical Assemblies to Support QSFP, CFP and CXP Industry Standard Pinout Configurations QSFP,
More informationQuante BPEO Splice-Protection Closure for Optical Fiber Cables. Features Advantages Benefits
3 Quante BPEO Splice-Protection Closure for Optical Fiber Cables BPEO: Fully Mechanical, Easy to Install, No Specific Tools BPEO is the newest generation of watertight spliceprotection closures for optical
More informationQuick Term II Silicone Rubber Termination Kits for Shielded Cables Instruction Sheet
Quick Term II Silicone Rubber Termination Kits for Shielded Cables Instruction Sheet Tape Shield Wire Shield UniShield UniShield is a registered trademark of Cablec Corporation Kit No. 5696K 5697K Cable
More informationPRO-HDMI2HD. HDMI to SDI/3G-HD-SD Converter. User Manual. Made in Taiwan
PRO-HDMI2HD HDMI to SDI/3G-HD-SD Converter User Manual Made in Taiwan rev.1008 103 Quality Circle, Suite 210 Huntsville, Alabama 35806 Tel: (256) 726-9222 Fax: (256) 726-9268 Email: service@pesa.com Safety
More information3M Cross-Connect Cabinets 4220SVB, 4220SVC and 4220SVE Skirt and Stabilizers
3M Cross-Connect Cabinets 4220SVB, 4220SVC and 4220SVE Skirt and Stabilizers Rear skirt and stabilizers to cover and protect DSLAM apparatus cases mounted directly on 3M Pad or Stake Mount Cabinets Instructions
More information3 Closure preparation 3.1 Work-stand 3.2. Opening FIST-GCOG2-Dx Preparing drop cable with micro-tubes
FIST-GCOG2-Dx24 I N S T A L L A T I O N I N S T R U C T I O N FTTH closure for micro-tubes and micro-cables Content 1 Introduction 2 Kit content 3 Closure preparation 3.1 Work-stand 3.2. Opening FIST-GCOG2-Dx24
More information3M Super 23 Electrical Tape
WEATHERPROOFING S CHEMICALS ET 3M SUPER 23 Features: Premium all-weather black electrical tape Remains conformable at -18 C /0 F 7mm thickness UV resistant Part # Size ET 3M Super 23 19mm x 9.15m WEATHERPROOFING
More informationSC Connector. Fiber Optic Connectors. MDR Electronics
SC Connector Fiber Optic Connectors MDR Electronics www.mdrelectronics.com Table of contents 1. Introduction 3 2. Image and line drawing 4 3. Types of connector 5 4. Specifications 6 5. Ask for assistance
More informationK & B Flame Retardant Building Riser Closures
K & B Flame Retardant Building Riser Closures September 1995 Issue 1, 34-7016-7030-8 1. General 1.1 3M Brand K&B Building Riser Closures are designed for use in building riser closets and may be positioned
More informationMOST - Roadmap Physical Layer & Connectivity from 150Mbps to 5Gbps
MOST - Roadmap Physical Layer & Connectivity from 150Mbps to 5Gbps 13th MOST(R) Interconnectivity Conference Asia on November 15, 2012 in Seoul, South Korea Andreas Engel Manager Advanced Infotainment
More information32 Channel CPCI Board User Manual
0 Sections Page 1.0 Introduction 1 2.0 Unpacking and Inspection 1 3.0 Hardware Configuration 1 4.0 Board Installation 5 5.0 I/O Connections and the Front Panel 5 5.1 Front Panel Layout 5 5.2 Input and
More informationHDSI Series Tensolite High-Performance Cable & Interconnect Systems
HDSI Series Tensolite High-Performance Cable & Interconnect Systems Tensolite's High Density Shielded Interconnect Products Tensolite s HDSI and HDSI-DP assemblies use ribbonized coaxial cable, matched
More information10Gb/s SFP+ ER 1550nm Cooled EML with TEC, PIN Receiver 40km transmission distance
Feature 10Gb/s serial optical interface compliant to 802.3ae 10GBASE-ER/EW Electrical interface compliant to SFF-8431 specifications for enhanced 8. and 10 Gigabit small form factor pluggable module SFP+
More information