Professional Quad HDTV IRD

Transcription

1 Professional Quad HDTV IRD User Manual

2 Contents 1. Overview Features Technical Specifications Block Diagram Front panel and rear panel instructions Front panel Rear panel Operation instructions on front panel Status Config System Web Control Status Page Configuration Page System Page Installation Notices COPYRIGHT (Copyright 2013 Beijing Jaeger Communication Electronic Technology Co., Ltd.) Not to be copied, used or translated in part or whole without Beijing Jaeger prior consent in writing except approval of ownership of copyright and copyright law. WARRANTY

3 This warranty does not cover parts which may become defective due to misuse of the information contained in this manual. Read this manual carefully and make sure you understand the instructions provided. For your safety, be aware of the following precautions. WARNING! IMPORTATNT SAFETY INSTRUCTIONS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To avoid explosion danger, do not dispose of batteries in an open fire. CE MARK FOR EUROPEAN HARMONISED STANDARDS The CE mark which is attached to these products means it conforms to EMC Directive (89/336/EEC) and Low Voltage Directive (73/23/EEC). IMPORTANT INFORMATION Please retain the original packaging, should it be necessary at some stage to return the unit. Disposal of Old Electrical and Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems) This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service, or the shop where you purchased the product. COPYRIGHTS Television programs, movies, video tapes, discs, and other materials may be copyrighted. Unauthorized recording of copyrighted material may be against the copyright laws in your region. Also, use of this product with cable television transmissions may require authorization from the cable television operator or transmitter/owner. VENTILATION Do not expose the product to high temperatures, such as placing it on top of other product that produce heat or in places exposed to direct sunlight or spot lights. The ventilation slots on top of the product must be left uncovered to allow proper airflow into the unit. Do not stand the product on soft furnishings or carpets. Do not stack electronic equipment on top of the product. Do not place the product in a location subject to extreme changes in temperature. The temperature gradient should be less than 10 degrees C/hour. Place the product in a location with adequate ventilation to prevent the build-up of heat inside the product. The minimum ventilation space around the unit should be 7 cm. The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table cloth, curtains, etc. POWER SOURCES The product is not disconnected from the AC power source (mains) as long as it is connected to the power outlet or wall socket, even if the product is turned off. If the product will not be used for a long period of time, disconnect it from the AC power outlet or wall socket.

4 Before Using the Device Thank you for purchasing the DXP-3400P Professional Quad HDTV IRD. This User Manual is written for operators/users of the DXP-3400P to assist in installation and operation. Please read this user manual carefully before installation and use of the device. FOR YOUR SAFETY This equipment is provided with a protective earthing ground incorporated in the power cord. The main plug shall only be inserted in a socket outlet provided with a protective earth contact. Any interruption of the protective conductor, inside or outside the device, is likely to make the device dangerous. Do not remove the covers of this equipment. Hazardous voltages are present within this equipment and may be exposed if the covers are removed. Only Beijing Jaeger trained and approved service engineers are permitted to service this equipment. The supplied AC power cable must be used to power the device. If the power cord becomes damaged it must be replaced. No operator serviceable parts inside. Refer servicing to Beijing Jaeger trained and approved service engineers. For the correct and safe use of the device, it is essential that both operating and servicing personnel follow generally accepted safety procedures in addition to the safety precautions specified in this manual. Whenever it is likely that safety protection is impaired, the device must be made in-operative and secured against unintended operation. The appropriate servicing authority must be informed. For example, safety is likely to be impaired if the device fails to perform the intended measurements or shows visible damage. WARNINGS The mounting environment should be relatively dust free, free of excessive vibration and the ambient temperature between 0C to 40C. Relative humidity of 20% to 80% (non-condensed) is recommended. Avoid direct contact with water. Never place the equipment in direct sunlight. The outside of the equipment may be cleaned using a lightly dampened cloth. Do not use any cleaning liquids containing alcohol, methylated spirit or ammonia etc. For continued protection against fire hazard, replace line fused only with same type. Air intake for cooling is achieved via holes at the side of the device and the fans inside. The air flow should not be obstructed. Therefore, the device has to be placed on a flat surface, leaving some space at the sides of the device. When in operation, the internal temperature should not exceed the limit of 70C. 1. Overview The DXP-3400P provides operators an ideal solution for multi receiving, re-multiplexing, descrambling and decoding operations. By the quad DVB common interfaces, DXP-3400P could decrypt multiple services in 4

5 transport stream. DXP-3400P is also a professional IRD that features a broadcast quality decoder for MPEG-2 and MPEG-4 AVC/H.264 in both Standard Definition and High Definition formats, and provides a variety of industry standard digital and analog outputs, including 4 separated CVBS video, analog Audio, SD-SDI and HD-SDI. The unit also performs HD down-conversion and aspect ratio adaptation of HD programs to generate professional quality baseband analog video and audio outputs for easy integration with existing cable network infrastructure. This all-in-one architecture makes the DXP-3400P an ideal product for distribution and contribution networks. 2. Features Quad Tuner Input, Supports variety of input options DVB-T2/S2/S/C/T/DTMB/ATSC/ISDB-T Supports DVB-S2 Input Stream Identifier (ISI, optional) and DVB-T SFN MIP pass through SD/HD MPEG-2 and MPEG-4 AVC/H.264 digital video decoding Two Audio PIDs decode or pass through (compressed) for each SDI output Built-in 2xTS re-multiplexer, one receives from Tuner1, Tuner2, CI1 and CI2 Inputs, the other receives from Tuner3, Tuner4, CI3 and CI4 Inputs 4 DVB-CI Slots, multi-program decryption, BISS-1 and BISS-E decryption Dynamic PMT detection and automatic updating Supports VBI TELETEXT, EBU/DVB Subtitle, Closed Caption Remote Control and Supervision by SNMP, HTTP WEB and Proprietary HDMS software PCM audio embedded in SDI and HDMI outputs AC3 audio can be passed through by SDI VBI TELETEXT, WSS and Closed Caption embedded in SDI On Site software update through IP or USB RSSI, received Eb/No & BER monitoring Redundancy power supply 3. Technical Specifications Tuner Input DVB-S/S2 Tuner Input (ISI Factory Optional) Connector Type Input Frequency Range Input Level Symbol Rate 4 F type female 75Ω for Input 950 ~ 2150MHz -25 ~ -65dBm 2 ~ 45MBaud Roll-off Factor DVB-S QPSK: 0.35

6 DVB-S2 8PSK: 0.35, 0.25, 0.2 DVB-S QPSK: 1/2, 2/3, 3/4, 5/6, 7/8 FEC Code Rate DVB-S2 QPSK: 1/2, 3/5, 2/3, 3/4, 4/5, 5/6, 8/9,9/10 DVB-S2 8PSK: 3/5, 2/3, 3/4, 5/6, 8/9, 9/10 LNB Polarity Selection Voltage LNB Band Selection Tone 0, 13V, 18V selectable 0/22KHz selectable Satellite Selection Command DiSEqC 1.0 ISI ID 1 ~ 255 user configurable DVB-C Tuner Input Connector Type Input Frequency Range Input Level 4 F type female 75Ω for Input 51 ~ 862MHz 51 ~ 75dBµV Symbol Rate 1 ~ 7MBaud (ITU J.83 Annex A) Constellation Bandwidth Input Return Loss 16QAM, 32QAM, 64QAM, 128QAM, 256QAM 6MHz, 7MHz, 8MHz 7dB (typ.) DVB-T/T2 Tuner Input Connector Type Input Frequency Input Level Constellation Bandwidth FFT Mode Guarding Interval FEC Code Rate Input Return Loss 4 F type female 75Ω for Input 104 ~ 862MHz (VHF/UHF) -20 ~ -70dBm DVB-T: QPSK, 16QAM, 64QAM DVB-T2: QPSK, 16QAM, 64QAM, 256QAM 6MHz, 7MHz, 8MHz DVB-T: 2K, 8K DVB-T2: 1K, 2K, 4K, 8K, 16K, 32K DVB-T: 1/4, 1/8, 1/16, 1/32 DVB-T2: 1/4, 5/32, 1/8, 5/64, 1/16, 1/32, 1/64, 1/128 DVB-T: 1/2, 2/3, 3/4, 5/6, 7/8 DVB-T2: 1/2, 3/5, 2/3, 3/4, 4/5, 5/6 7dB (typ.) DTMB Tuner Input

7 Connector Type Input Frequency Range Input Level Symbol Rate Bandwidth Constellation Guard Interval 4 F type female 75Ω for Input 46.5~866MHz -87~-29dBm 7.56MBaud 6MHz/7MHz/8MHz 4QAM-NR,4QAM,16QAM,32QAM,64QAM PN420, PN595, PN945 Roll-off Factor 0.05 Interleaving Depth 240,720 FEC Code Rate 0.4, 0.6, 0.8 ATSC Tuner Input Connector Type Input Frequency Range Input Level Symbol Rate Constellation 4 F type female 75Ω for Input 54~864MHz -75~-7dBm(ATSC 8VSB) MBaud 8VSB Roll-off Factor Bandwidth 6MHz TS Processing TS Input Management TS Output Management Demux and Remux among Tuner and CI Inputs Demux and Remux for 4 independent ASI outputs Service and PID Management Remux, filtering and remapping PSI/SI Descrambler BISS Mode Common Interface PSI/SI table regeneration, NIT and SDT edition, LCN Edition and Regeneration DVB Common Scrambling Algorithm (CSA) BISS-1, BISS-E 4x1 PCMCIA slots, compatible with major CA CAMs in the market ASI Output Connector Type Standard Output Bit Rate TS Processing 4 independent BNC female, 75Ω DVB-ASI, EN Mb/s 2 Independent TS Re-multiplexer:

8 Remux 1: TS Re-multiplexed from tuner1, Tuner2, CI1 and CI2, Remux 2: TS Re-multiplexed from tuner3, Tuner4, CI3 and CI4 Digital Video Processing Video Standard ML for SD, for HD) MPEG 4/H.264 AVC Part 10 for SD, for HD) SDI Video Resolution Video PID Bit Rate 1080i 30, 1080i 29.97, 1080i 25, 720p 60, 720p 59.94, 720p 50, 576i 25, 480i Mb/s HD/SD-SDI or ASI Output Connector Type SD Standard HD Standard Level Embedded Audios 4 Pairs of SDI output, BNC, female, 75Ω SMPTE 259M, 270 Mb/s (10bit) SMPTE 292M, Gbit/s (10bit) 800mV p-p MPEG-1 Layer 2 a. 2 stereo pairs (Stereo, Dual Mono, Left, Right) Dolby Digital (AC3) a. 5.1 down-mix to 2.0 (Stereo, Dual Mono, Left, Right) b. Dolby Digital Audio Pass-through Dolby Digital Plus(AC3+) a. 5.1 down-mix to 2.0 (Stereo, Dual Mono, Left, Right) b. Dolby Digital Audio Pass-through MPEG-2 AAC a. 5.1 down-mix to 2.0 (Stereo, Dual Mono, Left, Right) b. 2.0 (Stereo, Dual Mono, Left, Right) MPEG-4 HE-AAC v1/v2 a. 5.1 down-mix to 2.0 (Stereo, Dual Mono, Mono, Left, Right) b. 2.0 (Stereo, Dual Mono, Left, Right) Embedded Ancillary Data Teletext, WSS, CC Analog Video Output CVBS Connector CVBS Standard CVBS Resolution 4 BNC female 75Ω NTSC, PAL, and SECAM 576i 25, 480i 29.97

9 Nominal Output Level Frequency Response Chroma-Luma Delay 1.0 Vp-p±5% (with standard test stream) <±1 db, at 5.5 MHz for PAL/SECAM, 4.2MHz for NTSC <±30 ns Field Time Distortion <2% Line Time Distortion <1% Short Time Distortion <2% Differential Gain <3% Differential Phase <2 Signal to Noise Ratio >55dB (luminance weighted) Analog Audio Output Connector Type Output Impedance Output Mode Number of Output Cross Talk Among Channels THD Frequency Response Output Level 2 D-sub 9 male included 4 pairs of stereo audio with XLR adaptor cable 600Ω (balanced) Left, Right, Dual Mono, Stereo 4 pairs of stereo audio outputs (4 Audio PIDs or 8 audio channels are decoded) >70dB 400Hz, 1KHz test tone ±0.5dB over 20Hz ~ 18KHz 0dBm in 600Ω (0dBu), adjustable range ±10dB Ancillary Data Processing Subtitle VBI Closed Caption DVB, EBU Teletext, WSS EIA 608, EIA 708, EIA 608-to-708 Control & Monitoring Connector Type Remote Control Local Control Serial Port Equipment Upgrade 1 RJ-45, 10/100 Base-T, for equipment IP Control SNMP, HTTP (Web Interface), Proprietary HDMS (Headend Device Management System) LCD display and 6-key keypad 1 RS-232 D-sub female, for debug use only Embedded FTP loader, WEB HTTP and USB Physical Dimension Weight 505mm 445mm 45mm 3.5kg

10 Power Supply Power Consumption AC 90V ~ 250V, 50/60Hz 24W (exclusive of LNB power) Operating temperature 0 ~ 45 Storage temperature -10 ~ 60 Operating Humidity 10 ~ 90%, non-condensed Certification EMC: EN 55024:1998+A1:2001+A2:2003, EN 55022:2006+A1:2007, EN :2006, EN :2008 FCC: Part 15 Class B LVD: EN : A11:2009 * For more information about digital audio pass through, please contact our sales representative. 4. Block Diagram

11 5. Front panel and rear panel instructions 5.1 Front panel Name LED Power LED Warning Function When turned on, the Green LED indicates that power is available. When turned off, the power is not available or failed Reserved for warning info. When turned on, the Green LED indicates that the device is working properly, the Red LED indicates there is warning on device.

12 LED Alarm LED Tuner 1~4 LED Decoder 1~4 LCD Display Cursor Keys ENTER key EXIT Key Control RJ-45 Control USB Reserved for alarm info. When turned on, the Green LED indicates that the device is working properly, the Red LED indicates there is alarm on device. When turned on, the Green LED indicates that the tuners are locked, the Red LED indicates the tuners are unlocked. When turned on, the Green LED indicates that the decoding function are working properly, the Red LED indicates the decoding function are failed. Display menus, submenus and its parameters UP, DOWN, LEFT, RIGHT. Used to navigate through the menu system Confirm a selection then return to previous menu Exit and return to previous menu To connect with PC for web control or HDMS control For firmware upgrade via USB storage stick 5.2 Rear panel Name RS-232 Alarm Tuner In 1-2 ASI Out 1-2 SDI Out 1-2 Common Interface 1-2 CVBS 1-2 Audio 1 Tuner In 3-4 ASI Out 3-4 SDI Out 3-4 Common Interface 3-4 Serial port for equipment debug use Reserved for Alarm Tuner-1 and Tuner-2 signal input ports Description ASI Out-1 and ASI Out-2 signal output ports Group 1 and 2 of SD or HD Serial Digital Video output ports (mirrored) To insert CI CAM modules CVBS-1 and CVBS-2 RCA video output ports AES/EBU and Balance Audio output port 1 (A special DB-9 conversion cable is offered as accessory) Tuner-3 and Tuner-4 signal input ports ASI Out-3 and ASI Out-4 signal output ports Group 3 and 4 of SD or HD Serial Digital Video output ports (mirrored) To insert CI CAM modules

13 CVBS 3-4 Audio 2 POWER SOCKET CVBS-3 and CVBS-4 RCA video output ports AES/EBU and Balance Audio output port 2 (A special DB-9 conversion cable is offered as accessory) AC 90~250V 50-60Hz inputs, redundant power supplies. Hot-swappable 6. Operation instructions on front panel Users are advised to restore factory setting of the machine before the first time using it. Users are advised not to change those temporarily useless parameters in order to avoid unnecessary fault. After power on, the Local IP address will be shown on the LCD. User can press ENTER to get into the main menu. In the main menu, there are 3 sub-menu, Press UP/DOWN to switch between the sub-menus. Status Config System After go into every sub-menu, you can press LEFT or RIGHT to move the cursor, then use UP or DOWN to change the value, and then you can press ENTER to make the selection. Submenu Name Status Config System Description Monitor the parameters of Tuner and decoding info. Configure the parameters of Input and output, including CI settings, AV decoder, ASI output and so on. Check and set system settings and read the equipment information, and make the default factory setting and so on. 6.1 Status In the Status menu, user can monitor the parameters of input and output, including Tuner, CI, AV decoder, TS and USB port. Choose Status and press UP or DOWN to scroll the sub-menus, press ENTER to go into the submenus. There are five sub-menus to configure: Tuner Decoder

14 TS CI Card Name USB Status Submenu Name TS Description To display bitrate of each tuner and whether tuner is locked AV Decoding Status To show video and audio decoding status Decoder Service Video Info Audio Info To show Service Type, Service Name, Provider Name, Service ID, PMT PID, PCR PID of decoded program. To show Video PID, Stream Type, Video Standard, Aspect Ratio of decoded program. To show Audio-1 PID, Audio-1 Format, Audio-1 Sample Rate, Audio-2 PID, Audio-2 Format, Audio-2 Sample Rate of decoded program. Tuner CI Card Name USB Status To show signal strength, Eb/N0, C/N and BER of each input signals. To show CI Card name when you insert any CI CAM card in CI slots. It will detect whether there is a USB flash drive inserted in USB port of device.

15 6.2 Config In the Configuration menu, user can configure and monitor the parameters of input and output, including Tuner, CI settings, AV decoder, ASI output, BISS, SDI and so on. Choose Configuration and press UP or DOWN to scroll the sub-menus, press ENTER to go into the sub-menus. There are six sub-menus to configure: Tuner Decoder ASI Output CI BISS SDI

16 Submenu Name LNB LO Frequency Satellite Frequency Symbol Rate Description To configure the local oscillator frequency according to the right satellite, its range is from 1000 to 26,500MHz. To configure the satellite down link frequency according to the right satellite, its range is from 1000 to 26,500MHz. To configure the symbol rate of QPSK signal, its range is from 1000 to 45,000KBaud. LNB Voltage To select the correct LNB voltage output from the F- connector, user can choose between Off, 13V and 18V. Tuner 1-4 LNB 22KHz To activate the LNB 22KHz control signal to the LNB, user can select between On and Off. DiSEqC To configure the DiSEqC control, user can select Port A, Port B, Port C, Port D or DiSEqC OFF. Decoder 1-4 ASI Output 1-4 CI 1-4 BISS 1-4 SDI 1-4 PLS Gold Code Freq Offset High Freq Offset Low Source Program Video Output Audio Output ASI Source CI Source CI Setup CI CAM Name BISS Mode BISS Source Program Emb Aud Switch To configure the PLS gold code, its range is from 0 to 262,141. To ensure the tuner locks the specific signal, its range is from 1000K to 5,000KHz. To ensure the tuner locks the specific signal, its range is from -5,000K to -1,000KHz. The condition is Freq Offset Low < Real IF - Setting IF < Freq Offset High. To configure the decoder source, user can select Tuner Input, CI or Remux Input. To configure which program should be decoded. To configure the video properties, such as the screen ratio, resolution, VBI issues and so on. To configure the audio properties, such as the audio PID, output level and so on. To select the ASI output source. To configure the CI descramble source, user can select Tuner Input or Remux Input. To set which programs should be descrambled by CI To check what kind of CAMs have been inserted. To select the BISS mode, user can choose between Off, BISS-1 and BISS-E. To select the BISS source, user can select Tuner Input. To select which services will be decrypted by BISS. To enable or disable the embedded audio

17 Emb Aud Mapping Emb Aud Level Closed Caption Mode To select which audio to be embedded in which group To configure the embedded audio level. To configure the Closed Caption mode over SDI, user can select between Auto, Line21, SMPTE and SMPTE 334M System In this menu, you can check and set system settings and read the equipment information, and make the default factory setting and so on. There are eight submenus, and press ENTER to go into each submenu. Version Info IP Control Device Label Factory Settings Machine Type System Reboot Brightness Upgrade

18 Submenu Name Version Info Description To display some properties of the device, such as software version. IP Address To configure the IP Address of the device. IP Control Network Mask Gateway HTTP Login MAC Address To configure the IP Net Mask of the device. To configure the IP Gateway of the device. To configure the user name and password of web access. To display the MAC address of the device Device Label Factory Settings To configure the name of the device. The switch to make factory default setting. MAC Address To configure the MAC address of the device. Machine Type S/N Dynamic PMT Switch To configure the serial number of the device. To enable or disable the dynamic PMT function. System Reboot Brightness Upgrade To reboot the device To configure the brightness of LCD screen on front panel. To start to upgrade firmware after inserting a USB storage which contain new firmware file into the USB port of the device. 7. Web Control DXP-3400P can be controlled by HTTP Web. After connecting the control port to a PC, User can type IP address of DCH-3400P in browser. The default IP address of DXP-3400P is , the default user name and password are root and If you forget these, you can change these by operating on front penal. 7.1 Status Page Here user can check working status of all functions, as it shown in figure below. 1) Input Status: Check whether the inputted TS are locked or not, as it shown in figure below.

19 2) Decoder: Check the video and audio decoding status of 4 programs, as it shown in figure below. 3) CI Status: Check the CI CAM information of 4 CI slots, as it shown in figure below.

20 7.2 Configuration Page User can check and configure parameters for all functions, it has 8 sub-pages. 1) Tuner: Check and configure the parameters for tuner input signal, as it shown in figure below, click the button Apply or Cancel to submit or undo your configuration.

21 2) Decoder: Check and configure the parameters for program decoding, it has 3 sub-pages incoding Decoder, Video and Audio, as it shown in figure below, click the button Apply or Cancel to submit or undo your configuration. (1) Decoder: User here can select the program which needs to be decoded according to the source of signal. User can also enable or disable the function of video and audio alarm, as it shown in figure below. (2) Video: User here can configure all the parameters for video decoding, as it shown in figure below.

22 (3) Audio: User here can configuration all the parameters for audio decoding, as it shown in figure below.

23 3) ASI Output: Check and select the signal source for ASI-1/ASI-2/ASI-3/ASI-4 output, as it shown in figure below, click the button Apply or Cancel to submit or undo your configuration. 4) CI: User here can choose the signal source for CI decryption function, and also user can monitor the information of programs decrypted, as it shown in figure below, click the button Apply or Cancel to submit or undo your configuration.

24 5) BISS: User here can choose the signal source for BISS decryption function and the mode of BISS, and also user can monitor the information of programs decrypted, as it shown in below figure for BISS-E, user have to keyin the ID and Key to decrypt the BISS-E encoded program, click the button Apply or Cancel to submit or undo your configuration. 6) SDI: There are 4 BNC output port on the rear panel. User can enable/disable embedded audio, close caption and embedded audio mapping here, as it shown in figure below, click the button Apply or Cancel to submit or undo your configuration.

25 7.3 System Page User can check all the system parameters of this device. 1) Device: User here can check some information of this device itself, such as the product name, the model and the service number. Click the button Apply or Cancel to submit or undo your new configuration, as it shown in figure below.

26 2) Version: User here can check the versions of all embed modules as it shown in figure below. 3) Upgrade: User can upgrade the version of device s firmware. As it shown in figure below, click the button Scan to select the firmware on local PC.

27 8. Installation Fix the device in the standard 19 rack. Connect the power cable. Turn on the device and wait for 1 to 2 minutes, while the device will complete self inspection and configuration. The POWER Indicator LED will always light on during working. If not use the device, please pull out the AC plug. If you want to reboot device, please leave it for at least 5 seconds after shutting it down.