Protecting ETO Alpha 76A Amplifiers

Size: px
Start display at page:

Download "Protecting ETO Alpha 76A Amplifiers"

Transcription

1 Protecting ETO Alpha 76A Amplifiers After acquiring a used Alpha 76A amplifier with 8874 tubes of unknown status, I was very pleased to discover the expensive 8874s were percolating well. However, I was also surprised to find the Alpha amplifier had no built in protective circuitry except for excessive plate current. Reflected power and high grid current protection depended upon the operator monitoring a front-panel meter. Some of this is welcomed especially the lack of high reflected power shutdown (I use 75Ω hardline; the pi network inside the amp will perfectly match this impedance but the 50Ω-referenced wattmeter will claim a mismatch exists). I d really prefer not having such protection. However, high grid current will readily damage tubes (did I mention that 8874s are expensive?), so automatically monitoring this parameter is desirable. The circuit presented here monitors grid current and temporarily disables the amplifier if it exceeds a set level. Ideas for extending the protection to reflected power and other fault conditions are also mentioned. This idea should also work with the Alpha 374/A and Alpha 78 amplifiers, which share control circuit design. Background & System Level Definition I ve used several amplifiers over the years, from sweep tube-based linears through Alpha 87As, including a few solid-state half-kw amps. Protection schemes varied from nothing in most of the amplifiers, to some fairly aggressive designs in the transistorized amps. Fault recovery also varied--some amps latch-off-line until manually reset; others stay off for a penalty delay, then automatically return to duty. Although I ve generally had good luck with my amplifiers, there was a problem here a couple of years ago that caused and arc that took out a band switch. This was due to a guest operator not properly tuning an unprotected AL After replacing the switch (turns out, an exact replacement was no longer available, so some modifications were needed), parasitic oscillations occurred that destroyed a couple of plate chokes, destroyed test equipment, stressed the power supply, and generally reduced my enthusiasm for both power amplifiers and guest operators! The 76A has automatic power-off shutdown protecting the amplifier from excessive plate current. Otherwise, amplifier longevity depends upon the operator monitoring the front panel meters, one of which may be switched between grid current, forward power, reflected power, and B+. Two other items were of interest: first, there is a factory-drilled rear panel hole marked AUX on the rear panel that might be used to bring out cabling. Another was the characteristics of the amplifier T/R key line. Open circuit (receive/standby mode), it presents +28VDC. When shorted to ground (transmit mode), it sources 70mA while idling, increasing to over 120mA with full output. This is because amplifier grid current flows thorough the T/R line. A little caution is necessary regarding the switch used in the driver transmitter: voltage drop across this switch will increase the amplifier bias point, causing it to become slightly less linear. Other considerations include the way the amplifier is enabled. Instead of a two-position OPERATE/STANDBY switch, it has a three-position dual push button. With both buttons out, the amplifier is in standby mode. The CW button enables the amplifier using the lower voltage transformer tap. The SSB button selects the high B+ tap. This design is a relic of the old US maximum power regulation, dictating a maximum of 1000W of DC input power for final stages. The present output power limit is better served with the amp in the SSB position full-time. Placing the amplifier into standby is a little bit tricky, requiring the operator depress both the CW and SSB buttons simultaneously; this is too complicated a manoeuver during a contest when one s hands are better kept on the keyboard K6XX 1 Grid Protection foralpha 76A Amplifiers The Alpha 76A. Yes, this is a lousy photograph. Photo 2. The rear panel has a factory-drilled hole above the T/R (RELAY) input.

2 I studied the protection schemes used in the Ameritron AL-1500 and the Alpha 91ß amplifiers. The AL-1500 latches itself off-line if a grid current fault occurs. The lamps on one of the front panel meters darkens and operator must manually toggle the OPERATE/STANDBY switch to return to operation. The 91ß shuts off all power if plate current is excessive, and switches off-line for several seconds if grid current or reflected power is high, or if throughput gain is low. Its delay time may be circumvented by manually toggling its standby switch. The 76A already has over-plate current shutdown, and a gain monitor is both complicated and does not contribute much if grid current is watched. I did not want a reflected-power limit. This meant the only other feature necessary to keep my 76A tubes happy and long-lived was automatic grid current monitoring. Since surgery was planned anyway, a proper solid-state T/R switch might as well be implemented to reduce the control switching requirements of the driving transmitter. Decisions, Decisions Once the goal was defined, several circuits were designed. One, a fully manual reset design, fires a transistor latch when high grid current flows and uses an external reset push button. Another uses an external box with a LM3914 LED bar graph driver that provides a moving display of grid current and fires a latch when the current pins the virtual meter. The manual reset circuit did not provide a visible indicator when the amplifier was switched off-line. The bar graph display circuit worked OK, but is a rather complicated way to solve a simple problem. This complexity is partially due to the way cut-off bias is implemented in the 76A. In Standby mode (either via the front-panel CW/SSB switch or when the amplifier is in receive mode), both sides of the grid current sense resistor float at 28V above chassis. When activated, the grid (actually, the cathode) side drops to about 5V. While the LM3914 will operate under these conditions, I worry that basic amplifier operation might be affected by transient current flow during T/R switching after the proper amount of bypass capacitance is added. Both of these grid protection circuits required external wiring through the rearpanel AUX hole. The implemented design is of intermediate complexity and requires no external wiring nor operator intervention. It uses common, unexciting parts in a straightforward circuit: an optoisolator, a venerable 555 timer, a voltage regulator, a low resistance N-channel power MOSFET, three low-cost bipolar transistors, and a few resistors and capacitors. Often, the most expensive portion of my designs are the connectors; this design requires none. This protection circuit does not affect amplifier operation in any way until a grid current fault is detected. Da Design The circuit is shown in Figure 1. Grid current is detected by the 10Ω resistor (R116 on the 76A s High Voltage & Control PCB), and is fed to the optoisolator via R1. When the optoisolator reaches threshold, it triggers the 555 timer (U2). This immediately forces the amplifier into standby mode and illuminates lamp B1. As long as the T/R line from the transmitter remains low, the amplifier remains latched off. Reset delay timing does not begin until this line pulls high (receive mode); this feature prevents hot switching the amplifier back on-line during a long transmission. Once the T/R line does go high, the short (switched in by Q2) across timing capacitor C1 is removed and the reset time interval begins. This interval is set by the product of Rt and C1. After it expires, the timer output drops low, B1 extinguishes and the amplifier is again ready for use. However, if the T/R line toggles low K6XX 2 Grid Protection foralpha 76A Amplifiers Protection Features 1. High Grid Current Protection 2. Solid State T/R Switching (no relay, low switch resistance) 3. Internal Installation (no external wires/switches, etc.) 4. Automatic Reset after Penalty Delay Photo 3. The innards. Rear panel at top, front panel at bottom. The 8874s live in the top left compartment. The Pi-L network is at the lower left. The RELAY jack is at top center, near the power transformer. The High Voltage & Control PCB covers the lower right quadrant.

3 Ω Figure 1. Grid Overcurrent Protect Circuit for Alpha 76, 374, and 78 Amplifiers. again DURING this interval, C1 is again discharged and the cycle is extended. Thus, an inattentive operator cannot repeatedly beat against those expensive grids. Hopefully, he will soon realize a fault has occurred and will pause to fix whatever is causing the problem. Drawbacks to this design include the lack of a manual reset you must wait for the Rt x C1 time delay before the amplifier is again ready for use and the fact that keying the amp during the delay interval resets the timer. On the other hand, you may set the interval time to whatever you choose. I use 0.68µF for C1 and 2.2MΩ for Rt. Delay time, D T, in seconds is set by D T = 1.1Rt x C1 (Either basic units or MΩ and µf) NOTE: Three-digit component designations represent original Alpha parts factory-installed inside the amplifier. K6XX 3 Grid Protection foralpha 76A Amplifiers

4 The grid overcurrent detect threshold is set by R1 working with the inherent forward voltage drop of the optoisolator (about 1.0 to 1.25V nominally). Since the optoisolator is operating at its threshold, the output load current represented by the 555 trigger pull-up resistor R2 is also important. 100kΩ is a good value for this resistor; if you use a different value, R1 might require adjustment. Further, as the amplifier heats up, the optoisolator threshold voltage drops a bit, which effectively drops the overcurrent detect limit. This drop is small because the optoisolator is located in the intake air stream, and does not significantly affect circuit performance. Remember, we are looking for fault protection; as long as the circuit allows normal grid currents of approximately 50 to 75mA and protects when this current reaches 150 to 200mA, all is satisfactory. The detect threshold current may be calculated as: I G(Shut-off) = 100 x R1(kΩ) Where I G is in ma and R1 in kω. An R1 value of 1.5kΩ resulted in a grid current threshold of 150mA. Using 2kΩ gave 200mA. While a variable resistor may be used, it really isn t necessary. I was tempted to use the 1.5kΩ resistor already on the control board (R117), but decided against it. If this resistor used, the internal grid current meter will provide inaccurately low readings due to the optoisolator loading it down. Construction and Installation My prototype was assembled using standard perfboard. The board is mounted on the rear panel of the amplifier through one slot of the ventilation air intake using a small bolt, washers and a nut (Photo 4). But before mounting it, disconnect the wire on the RELAY phono jack on the rear panel of the amplifier. This wire will connect to the new board, and the T/R line from the drain of Q1 replaces it on the jack. Four wires are routed to the 76A s High Voltage & Control PCB as shown in Photo 5. The current sense wires are tacked across R116, ensuring the anode side of the optoisolator goes to the R115 side of R116. Supply and ground connections are obtained by tapping across the 28V supply filter capacitor, C108. (NOTE: my schematic shows this is a 500µF capacitor, but my amplifier uses a 470µF no worries, though!). One or two wires route the indicator bulb B1 up behind one of the translucent meter faces so it is visible when it illuminates. Photo 5. Control PCB, with front panel at bottom. The components we hook onto are on the left side of the board. Indicator lamp B1 (not shown) should rest against the transluscent face of one of the meters (bottom). Ensure all wires are well insulated since those exposed bolt heads and 2W resistors are high voltage points! Operation After installation, the top cover was reinstalled and the amp fired up. Normal operation at full power was verified, Photo 4. The board is installed on the rear panel then the loading control was purposefully mistuned. As the between the power transformer and the tube grid current hit 150mA (full scale on the internal meter), the compartment. amp kicked off-line. After a couple of seconds, the transmitter K6XX 4 Grid Protection foralpha 76A Amplifiers

5 was keyed with lower drive. The amplifier responded by amplifying until the increasing drive again caused the grid current to exceed 150mA, where it again kicked off. Maintaining key-down on the transmitter, the amplifier remained off-line. Toggling the T/R line with receive periods less than about a second kept the amp off-line, but as soon as a receive period exceeding a second and a half or so occurred, the amplifier was rearmed and ready to try again, just as expected. Imagine that! No RF susceptibility problems have yet been detected. Circuit Additions This basic circuit may be expanded if further protection parameters are desired. Since reflected power measurement is already provided by the amplifier, it may be added to the protective parameters with a comparator, a few resistors and a diode. Figure 2 shows a possible configuration. When the reflected power rises, the watt meter s reflected power bridge outputs an increasing current to RRa and RRb. This level is compared to the voltage set by R A and R B. If the reflected power is too high, the comparator switches high, which triggers the 555 timer through D1. The remainder of the protection circuit functions the same as before. Another important parameter is exhaust air temperature. This might be implemented with another comparator and a temperature sensor, either silicon or bimetallic. On the other hand, if the exhaust air is too hot, a much longer delay time is probably warranted! Figure 2. Adding High Reflected Power Protection Conclusion While I m sure that some day my 8874s will bite the dust, I believe that day has been delayed a bit by the inclusion of overcurrent protection. I am working on a clean PC board version of this circuit. Is anyone interested? K6XX 5 Grid Protection foralpha 76A Amplifiers Text and circuit design 2005, 2006 R.P Wolbert and 26K Engineering Ver Feb06

16 Stage Bi-Directional LED Sequencer

16 Stage Bi-Directional LED Sequencer 16 Stage Bi-Directional LED Sequencer The bi-directional sequencer uses a 4 bit binary up/down counter (CD4516) and two "1 of 8 line decoders" (74HC138 or 74HCT138) to generate the popular "Night Rider"

More information

MASTR II BASE STATION 12/24V POWER SUPPLY 19A149979P1-120 VOLT/60 Hz 19A149979P2-230 VOLT/50 Hz

MASTR II BASE STATION 12/24V POWER SUPPLY 19A149979P1-120 VOLT/60 Hz 19A149979P2-230 VOLT/50 Hz Mobile Communications MASTR II BASE STATION 12/24V POWER SUPPLY 19A149979P1-120 VOLT/60 Hz 19A149979P2-230 VOLT/50 Hz CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALI- FIED PERSONNEL ONLY. TO

More information

4.9 BEAM BLANKING AND PULSING OPTIONS

4.9 BEAM BLANKING AND PULSING OPTIONS 4.9 BEAM BLANKING AND PULSING OPTIONS Beam Blanker BNC DESCRIPTION OF BLANKER CONTROLS Beam Blanker assembly Electron Gun Controls Blanker BNC: An input BNC on one of the 1⅓ CF flanges on the Flange Multiplexer

More information

Nutube.US. 6P1 Evaluation Board. User Manual

Nutube.US. 6P1 Evaluation Board. User Manual Nutube.US 6P1 Evaluation Board User Manual Introduction The 6P1 Evaluation Board (EVB) is a vehicle for testing and evaluating the Korg Nutube 6P1 dual triode in audio circuits. This product is designed

More information

Fixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v August 2009

Fixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v August 2009 Fixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v. 2.1 06 August 2009 I have had several requests to provide a fixed audio output from the K2. After looking at the circuits that

More information

18 GHz, 2.2 kw KLYSTRON GENERATOR GKP 24KP 18GHz WR62 3x400V

18 GHz, 2.2 kw KLYSTRON GENERATOR GKP 24KP 18GHz WR62 3x400V 18 GHz, 2.2 kw KLYSTRON GENERATOR GKP 24KP 18GHz WR62 3x400V With its characteristics of power stability whatever the load, very fast response time when pulsed (via external modulated signal), low ripple,

More information

[ Photos ] [ Wares ] [ Library ] [ Dave's Web ] [ Matt's Web ] Wares [ SWISH ] [ Simple Search ] [ Trunk Calc ]

[ Photos ] [ Wares ] [ Library ] [ Dave's Web ] [ Matt's Web ] Wares [ SWISH ] [ Simple Search ] [ Trunk Calc ] [ Photos ] [ Wares ] [ Library ] [ Dave's Web ] [ Matt's Web ] Wares [ SWISH ] [ Simple Search ] [ Trunk Calc ] Realistic PRO-2006 Hardware Modifications Note Edited on January 1st, 1970, 00:00 UT. Improper

More information

Multi-Key v2.4 Multi-Function Amplifier Keying Interface

Multi-Key v2.4 Multi-Function Amplifier Keying Interface Multi-Key v2.4 Multi-Function Amplifier Keying Interface ASSEMBLY & OPERATION INSTRUCTIONS INTRODUCTION The Harbach Electronics, LLC Multi-Key is a multi-function external device designed for the safe

More information

CAMTO LTD. Arc detecting system DC/AC

CAMTO LTD. Arc detecting system DC/AC CAMTO LTD Arc detecting system DC/AC Arc detecting system DC/AC The system is based on experience with arc protection since 1962. The system units are built into boxes that all fit on a 35 mm DIN-rail.

More information

GA A26497 SOLID-STATE HIGH-VOLTAGE CROWBAR UTILIZING SERIES-CONNECTED THYRISTORS

GA A26497 SOLID-STATE HIGH-VOLTAGE CROWBAR UTILIZING SERIES-CONNECTED THYRISTORS GA A26497 SOLID-STATE HIGH-VOLTAGE CROWBAR by J.F. Tooker, P. Huynh, and R.W. Street JUNE 2009 DISCLAIMER This report was prepared as an account of work sponsored by an agency of the United States Government.

More information

14 GHz, 2.2 kw KLYSTRON GENERATOR GKP 22KP 14GHz WR62 3x400V

14 GHz, 2.2 kw KLYSTRON GENERATOR GKP 22KP 14GHz WR62 3x400V 14 GHz, 2.2 kw KLYSTRON GENERATOR GKP 22KP 14GHz WR62 3x400V With its characteristics of power stability independent of the load, very fast response time when pulsed (via external modulated signal), low

More information

DIY KIT MHZ 8-DIGIT FREQUENCY METER

DIY KIT MHZ 8-DIGIT FREQUENCY METER This kit is a stand-alone frequency meter capable of measuring repetitive signals up to a frequency of 50MHz. It has two frequency ranges (15 and 50 MHz) as well as two sampling rates (0.1 and 1 second).

More information

HS-509 VIBRATION TRIP MODULE

HS-509 VIBRATION TRIP MODULE HS-509 VIBRATION TRIP MODULE 1. Overview The HS-509 is a configurable trip amplifier capable of accepting a 4-20mA signal from a HS-420 sensor and providing two trip action relay outputs along with an

More information

7 SEGMENT LED DISPLAY KIT

7 SEGMENT LED DISPLAY KIT ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS CREATE YOUR OWN SCORE BOARD WITH THIS 7 SEGMENT LED DISPLAY KIT Version 2.0 Which pages of

More information

OWNERS MANUAL LUNATEC V3 MICROPHONE PREAMPLIFIER AND A/D CONVERTER

OWNERS MANUAL LUNATEC V3 MICROPHONE PREAMPLIFIER AND A/D CONVERTER OWNERS MANUAL LUNATEC V3 MICROPHONE PREAMPLIFIER AND A/D CONVERTER LUNATEC 35 +48 35 +48 30 40 30 40 0 25 45 25 45 3 192 1 1 6 176.4 20 50 20 50 9 96 12 PEAK 88.2 55 55 RESET 48 10 60 2 10 60 2 21 44.1

More information

Summit Audio Model TLA-50 Tube Leveling Amplifier

Summit Audio Model TLA-50 Tube Leveling Amplifier Summit Audio Model TLA-50 Tube Leveling Amplifier ATTACK FAST SLOW MEDIUM 3 4 5 6 7 TUBE LEVELER 40 60 80 100 VU 3 4 5 6 TLA-50 7 FAST SLOW RELEASE OUTPUT RED. METER 2 1 0 10 GAIN 9 8 7 5 3 1 0 1 2 +3

More information

USER S GUIDE. 1 Description PROGRAMMABLE 3-RELAY LOGIC MODULE

USER S GUIDE. 1 Description PROGRAMMABLE 3-RELAY LOGIC MODULE 1 Description The is a programmable 3 relay logic module that may be used for multiple applications, including simple timing, door mounted sensor inhibiting and advanced relay sequencing. The contains

More information

COHERENCE ONE PREAMPLIFIER

COHERENCE ONE PREAMPLIFIER COHERENCE ONE PREAMPLIFIER OWNER S MANUAL TABLE OF CONTENTS Introduction Features Unpacking Instructions Installation Phono Cartridge Loading Basic Troubleshooting Technical Specifications Introduction

More information

Provides an activation of Relay 1 triggered by Input 1. The function also provides an option for reverse-logic on the activation of Input 1.

Provides an activation of Relay 1 triggered by Input 1. The function also provides an option for reverse-logic on the activation of Input 1. USER S GUIDE PROGRAMMABLE 3-RELAY LOGIC MODULE 1 Description The is a programmable 3 relay logic module that may be used for multiple applications, including simple timing, door mounted sensor inhibiting

More information

Safety Information. Camera System. If you back up while looking only at the monitor, you may cause damage or injury. Always back up slowly.

Safety Information. Camera System. If you back up while looking only at the monitor, you may cause damage or injury. Always back up slowly. Table of Contents Introduction...3 Safety Information...4-6 Before Beginning Installation...7 Installation Guide...8 Wiring Camera & Monitor...9-10 Replacement Installation Diagram...11 Clip-On Installation

More information

3B SCIENTIFIC PHYSICS

3B SCIENTIFIC PHYSICS B SCIENTIFIC PHYSICS Triode S 11 Instruction sheet 1/15 ALF 1 5 7 1 Guide pin Connection pins Cathode plate Heater filament 5 Grid Anode 7 -mm plug for connecting anode 1. Safety instructions Hot cathode

More information

NewScope-7A Operating Manual

NewScope-7A Operating Manual 2016 SIMMCONN Labs, LLC All rights reserved NewScope-7A Operating Manual Preliminary May 13, 2017 NewScope-7A Operating Manual 1 Introduction... 3 1.1 Kit compatibility... 3 2 Initial Inspection... 3 3

More information

Key Features and Functions. General Description

Key Features and Functions. General Description AU301-DP Product Name GR03490 Manufacturer's Part Number Technical Specification Summary Frequency Range 470-862MHz Typ. Gain 56 db P1dB 1900 W Typ. Efficiency > 40% At 1dBcp Analogue TV 1400 Wps Temperature

More information

MG-XV operating instruction. Measuring of norm signals, 4-8-digit. Panel instrument type MG-BV Construction instrument type MG-AV

MG-XV operating instruction. Measuring of norm signals, 4-8-digit. Panel instrument type MG-BV Construction instrument type MG-AV MG-XV operating instruction Measuring of norm signals, 4-8-digit Panel instrument type MG-BV Construction instrument type MG-AV Contents 1. Brief description... 3 2. Safety instructions... 3 2.1. Proper

More information

HIGH VOLTAGE SWITCH PERFORMANCE OF THE EIMAC X-2159 TETRODE ABSTRACT

HIGH VOLTAGE SWITCH PERFORMANCE OF THE EIMAC X-2159 TETRODE ABSTRACT HIGH VOLTAGE SWITCH PERFORMANCE OF THE EIMAC X-2159 TETRODE by Bobby R. Gray High Power Component & Effects Section Techniques Branch Surveillance Division Rome Air Development Center Griffiss Air Force

More information

OPERATION NOTES FOR PSIDEX AUDIO PGP-1A PRE-AMPLIFIER DESCRIPTION INSTALLATION

OPERATION NOTES FOR PSIDEX AUDIO PGP-1A PRE-AMPLIFIER DESCRIPTION INSTALLATION OPERATION NOTES FOR PSIDEX AUDIO PGP-1A PRE-AMPLIFIER DESCRIPTION The Psidex Audio Laboratory PGP- 1A is a vacuum tube based microphone preamp and program line amplifier designed to provide solid, robust

More information

Industrial Monitor Update Kit

Industrial Monitor Update Kit Industrial Monitor Update Kit (Bulletin Number 6157) Installation Instructions 2 Table of Contents Table of Contents Industrial Monitor Update Kit... 3 Overview... 3 Part 1 - Initial Preparation... 5 Part

More information

LED Backlight for Technics amplifiers

LED Backlight for Technics amplifiers LED Backlight for Technics amplifiers Technics SE-A900S Technics SE-A900SM2 Technics SE-A909S Technics SE-A1000 Technics SE-A1000M2 Technics SE-A1010 Rev. 1.2 B Description The LED module is designed to

More information

MODEL 2018 OPERATION MANUAL Firmware Version

MODEL 2018 OPERATION MANUAL Firmware Version Reno A&E Telephone: (775) 826-2020 4655 Aircenter Circle Facsimile: (775) 826-9191 Reno, Nevada 89502 Internet: www.renoae.com USA e-mail: contact@renoae.com MODEL 2018 OPERATION MANUAL Firmware Version

More information

Site Installation Model MP-8433

Site Installation Model MP-8433 Site Installation Model MP- Rev. //0 SCOREBOARD SITE INSTALLATION INSTRUCTIONS CAUTION: All American Scoreboards (AAS) recommends the sign be installed by a licensed contractor, and must meet all local

More information

2002 DP-2X Chassis Projection Television Information INSTRUCTOR Alvie Rodgers C.E.T. (Chamblee, GA.)

2002 DP-2X Chassis Projection Television Information INSTRUCTOR Alvie Rodgers C.E.T. (Chamblee, GA.) Dec 00 (ver g) Training Materials Prepared by: ALVIE RODGERS C.E.T. 00 and 00 MODEL RELEASE DIGITAL HD READY PTV Chassis Model # Aspect DP-7 5SWX0B 6X9 57SWX0B 65SWX0B DP-7D DP-6 DP- DP-G 57TWX0B 6X9 65TWX0B

More information

Nixie Clock Type Quattro'

Nixie Clock Type Quattro' Assembly Instructions And User Guide Nixie Clock Type Quattro' - 1 - Issue Number Date REVISION HISTORY 2 8 Sept 2012 Errors corrected 1 27 July 2012 New document Reason for Issue - 2 - 1.1 Nixie Quattro

More information

Site Installation Model MP-8424

Site Installation Model MP-8424 Site Installation Model MP- Rev. //0 SCOREBOARD SITE INSTALLATION INSTRUCTIONS CAUTION: All American Scoreboards (AAS) recommends the sign be installed by a licensed contractor, and must meet all local

More information

Bill of Materials: Super Simple Water Level Control PART NO

Bill of Materials: Super Simple Water Level Control PART NO Super Simple Water Level Control PART NO. 2169109 Design a simple water controller in which electrodes are required to sense high and low water levels in a tank. Whenever the water level falls below the

More information

Mapletree Audio Design

Mapletree Audio Design Ultra 4C Preamplifier Mapletree Audio Design Ultra 4C Stereo Phono/Line Preamplifier PS 2D Power Supply User s Manual Rev. Mar. 22, 2019 Mapletree Audio Design R. R. 1, Seeley's Bay, Ontario, Canada, K0H

More information

DL-1A. RF dummy load - 50Ω 20W. Assembly manual. Last update: May 1, Thank you for constructing the DL-1A dummy load kit

DL-1A. RF dummy load - 50Ω 20W. Assembly manual. Last update: May 1, Thank you for constructing the DL-1A dummy load kit DL-1A RF dummy load - 50Ω 20W Assembly manual Last update: May 1, 2016 ea3gcy@gmail.com Updates and news at: www.qsl.net/ea3gcy Thank you for constructing the DL-1A dummy load kit Have fun assembling it

More information

CATHODE RAY OSCILLOSCOPE. Basic block diagrams Principle of operation Measurement of voltage, current and frequency

CATHODE RAY OSCILLOSCOPE. Basic block diagrams Principle of operation Measurement of voltage, current and frequency CATHODE RAY OSCILLOSCOPE Basic block diagrams Principle of operation Measurement of voltage, current and frequency 103 INTRODUCTION: The cathode-ray oscilloscope (CRO) is a multipurpose display instrument

More information

WC-2100 WORD CLOCK DISTRIBUTION AMPLIFIER INSTRUCTION MANUAL

WC-2100 WORD CLOCK DISTRIBUTION AMPLIFIER INSTRUCTION MANUAL WC-2100 WORD CLOCK DISTRIBUTION AMPLIFIER INSTRUCTION MANUAL SIGMA ELECTRONICS, INC. P.O. Box 448 1027 COMMERCIAL AVE. EAST PETERSBURG, PA 17520-0448 (717) 569-2681 WC-2100 WORK CLOCK DISTRIBUTION AMPLIFIER

More information

Application Note No. 157

Application Note No. 157 Application Note, Rev. 1.2, April 2008 Application Note No. 157 BFP450 SIEGET Transistor as an 869 MHz Power Amp in an Alarm Transmitter Monitor Application RF & Protection Devices Edition 2008-04-04 Published

More information

Modifying the RW1127 and similar TWTs for 24GHz

Modifying the RW1127 and similar TWTs for 24GHz Modifying the RW1127 and similar TWTs for 24GHz Some notes by Brian G4NNS updated after the EME conference. Issue 1.04 During a visit from Johannes DF1OI he explained how Ulli DK3UC had modified Siemens

More information

QUIZ BUZZER KIT TEACHING RESOURCES. Version 2.0 WHO ANSWERED FIRST? FIND OUT WITH THIS

QUIZ BUZZER KIT TEACHING RESOURCES. Version 2.0 WHO ANSWERED FIRST? FIND OUT WITH THIS TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE WHO ANSWERED FIRST? FIND OUT WITH THIS QUIZ BUZZER KIT Version 2.0 Index of Sheets TEACHING RESOURCES

More information

University of Illinois at Urbana-Champaign

University of Illinois at Urbana-Champaign University of Illinois at Urbana-Champaign Digital Electronics Laboratory Physics Department Physics 40 Laboratory Experiment 3: CMOS Digital Logic. Introduction The purpose of this lab is to continue

More information

Phono Amplifier brinkmann «EDISON» Manual.

Phono Amplifier brinkmann «EDISON» Manual. Phono Amplifier brinkmann «EDISON» ----------------------------------------------------------------------------------------------- Manual Preface We congratulate you on the purchase of our «EDISON» phono

More information

MODIFYING A SMALL 12V OPEN FRAME INDUSTRIAL VIDEO MONITOR TO BECOME A 525/625 & 405 LINE MULTI - STANDARD MAINS POWERED UNIT. H. Holden. (Dec.

MODIFYING A SMALL 12V OPEN FRAME INDUSTRIAL VIDEO MONITOR TO BECOME A 525/625 & 405 LINE MULTI - STANDARD MAINS POWERED UNIT. H. Holden. (Dec. MODIFYING A SMALL 12V OPEN FRAME INDUSTRIAL VIDEO MONITOR TO BECOME A 525/625 & 405 LINE MULTI - STANDARD MAINS POWERED UNIT. H. Holden. (Dec. 2017) INTRODUCTION: Small open frame video monitors were made

More information

VK-P10SE WARRANTY REGISTRATION FORM

VK-P10SE WARRANTY REGISTRATION FORM VK-P10SE WARRANTY REGISTRATION FORM Unit Serial Number: Customer Name: Address: Date of Purchase: Purchased From: Dealer Name: Address: IMPORTANT NOTE: In order to receive the full five-year product warranty,

More information

Tube Cricket Build Guide

Tube Cricket Build Guide Tube Cricket Build Guide The Tube Cricket is a small-wattage amp that puts out about 1 watt of audio power. With a 12AU7 tube-preamp and a JRC386 power amp, the Tube Cricket gives you great tone in a compact

More information

COLOUR CHANGING USB LAMP KIT

COLOUR CHANGING USB LAMP KIT TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE SEE AMAZING LIGHTING EFFECTS WITH THIS COLOUR CHANGING USB LAMP KIT Version 2.1 Index of Sheets TEACHING

More information

"Sophisticated Model Railroad Electronics"

Sophisticated Model Railroad Electronics LOGIC RAIL TM "Sophisticated Model Railroad Electronics" TECHNOLOGIES 21175 Tomball Pkwy Phone: (281) 251-5813 Suite 287 email: info@logicrailtech.com Houston, TX 77070 http://www.logicrailtech.com Block

More information

Solid-State Digital Timer

Solid-State Digital Timer Solid-State Digital Timer 1/16 DIN, Digital-Set Timer with 0.1 Second to 9,990 Hours Range 8 field-selectable operation modes Universal AC/DC supply voltage timers available Operations include ON-delay,

More information

Total solder points: 123 Difficulty level: beginner 1. advanced AUDIO ANALYZER K8098. audio gea Give your. . high-tech ILLUSTRATED ASSEMBLY MANUAL

Total solder points: 123 Difficulty level: beginner 1. advanced AUDIO ANALYZER K8098. audio gea Give your. . high-tech ILLUSTRATED ASSEMBLY MANUAL Total solder points: 123 Difficulty level: beginner 1 2 3 4 5 advanced AUDIO ANALYZER K8098 ra audio gea Give your. look high-tech ILLUSTRATED ASSEMBLY MANUAL H8098IP-1 Features & Specifications Features

More information

Australian Technical Production Services

Australian Technical Production Services Australian Technical Production Services Dual Rail Crowbar Copyright notice. These notes, the design, schematics and diagrams are Copyright Richard Freeman, 2015 While I am happy for the notes to be printed

More information

AK-PVE4 Operating Instructions. Measuring of norm signals in wall-type units. Performance:

AK-PVE4 Operating Instructions. Measuring of norm signals in wall-type units. Performance: AK-PVE4 Operating Instructions Measuring of norm signals in wall-type units 1 2 P Performance: Digit heights: 20 mm Colour: red Display range: -999 9999 Wall-type housing: light grey made of ABS-plastic

More information

A Unique Power Supply for the PEP II Klystron at SLAC*

A Unique Power Supply for the PEP II Klystron at SLAC* I : SLAC-PUB-7591 July 1997 A Unique Power Supply for the PEP II Klystron at SLAC* R. Case1 and M. N. Nguyen Stanford Linear Accelerator Center Stanford University, Stanford, CA 94309 Presented at the

More information

Musical Concepts. Chameleon PC-1T. Circuit Description

Musical Concepts. Chameleon PC-1T. Circuit Description PC-1T PC-1T is the standard Active Board. The input signal is DC coupled. This vacuum tube line stage preamplifier uses a single twin triode(6dj8/6922). It operates as a single-stage per channel grounded

More information

TUBE CONVERTERS EL84. Yellow Jackets Types YJS p. 2 YJSHORT p. 3 YJC p. 3 YJ20 p. 4 YJUNI p. 4 YJ7591 p. 4 YJR p. 5. screen grid 9. control.

TUBE CONVERTERS EL84. Yellow Jackets Types YJS p. 2 YJSHORT p. 3 YJC p. 3 YJ20 p. 4 YJUNI p. 4 YJ7591 p. 4 YJR p. 5. screen grid 9. control. TUBE CONVERTERS Yellow Jackets tube converters allow EL power tubes to be used in place of the most common guitar amp power tubes including L, EL, V, 0, 0 and 9. Most Yellow Jackets provide a substantial

More information

Output Board - v2* 4.1 Overview. 4.2 Audio Circuitry Program and Audition Outputs

Output Board - v2* 4.1 Overview. 4.2 Audio Circuitry Program and Audition Outputs Output Board - v2* 4.1 Overview This circuit board provides the following console functions: Line output amplification Cue amplification Headphone amplification External Inputs (balanced *) Monitor sends

More information

P User's Manual. Digital RF Power/ V.S.W.R. Indicator. RF Applications, Inc Production Drive Mentor, OH

P User's Manual. Digital RF Power/ V.S.W.R. Indicator. RF Applications, Inc Production Drive Mentor, OH User's Manual P-3000 Digital RF Power/ V.S.W.R. Indicator RF Applications, Inc. 7345 Production Drive Mentor, OH 44060 440.974.1961 Manufactured in the U.S.A. Part Number 96A05801 Revision C February 2000

More information

USER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.1

USER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.1 by USER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.1 www.aeroforcetech.com Made in the USA! WARNING Vehicle operator should focus primary attention to the road while using the Interceptor. The information

More information

Ten-Tec (865) Service Department:(865)

Ten-Tec (865) Service Department:(865) Ten-Tec (865) 453-7172 Service Department:(865) 428-0364 Installation Instructions for Ten-Tec Jupiter AT538K Tuner Kit The installation of the AT538K is divided into two steps. The first step is to reprogram

More information

DIFFERENTIAL CONDITIONAL CAPTURING FLIP-FLOP TECHNIQUE USED FOR LOW POWER CONSUMPTION IN CLOCKING SCHEME

DIFFERENTIAL CONDITIONAL CAPTURING FLIP-FLOP TECHNIQUE USED FOR LOW POWER CONSUMPTION IN CLOCKING SCHEME DIFFERENTIAL CONDITIONAL CAPTURING FLIP-FLOP TECHNIQUE USED FOR LOW POWER CONSUMPTION IN CLOCKING SCHEME Mr.N.Vetriselvan, Assistant Professor, Dhirajlal Gandhi College of Technology Mr.P.N.Palanisamy,

More information

Assembly Instructions And User Guide. Nixie FunKlock. FunKlock Issue 4 (1 February 2017)

Assembly Instructions And User Guide. Nixie FunKlock. FunKlock Issue 4 (1 February 2017) Assembly Instructions And User Guide Nixie FunKlock - 1 - Issue Number Date REVISION HISTORY 4 1 February 2017 New diode for D2 3 27 December 2013 C7 / C8 error page 15 2 7 November 2013 Errors corrected

More information

BooBox Flex. OPERATING MANUAL V1.1 (Feb 24, 2010) 6 Oakside Court Barrie, Ontario L4N 5V5 Tel: Fax:

BooBox Flex. OPERATING MANUAL V1.1 (Feb 24, 2010) 6 Oakside Court Barrie, Ontario L4N 5V5 Tel: Fax: BooBox Flex OPERATING MANUAL V1.1 (Feb 24, 2010) 6 Oakside Court Barrie, Ontario L4N 5V5 Tel: 905-803-9274 Fax: 647-439-1470 www.frightideas.com Connections The BooBox Flex is available with Terminal Blocks

More information

Lab 7: Soldering - Traffic Light Controller ReadMeFirst

Lab 7: Soldering - Traffic Light Controller ReadMeFirst Lab 7: Soldering - Traffic Light Controller ReadMeFirst Lab Summary The two way traffic light controller provides you with a quick project to learn basic soldering skills. Grading for the project has been

More information

1.5mm amplitude at 10 to 55Hz frequency in each X, Y, Z direction for 2 hours 500m/s² (approx. 50G) in each X, Y, Z direction for 3 times

1.5mm amplitude at 10 to 55Hz frequency in each X, Y, Z direction for 2 hours 500m/s² (approx. 50G) in each X, Y, Z direction for 3 times Color Mark Color Mark Feature Outstanding color matching accuracy - RGB light emitting diodes and 12-bit resolution - 2 detection modes (color only / color + intensity) - -step sensitivity adjustment for

More information

Pixie Construction Notes

Pixie Construction Notes Pixie Construction Notes PCB V2a February 4 th 2015 Please note that this document is still currently under revision and we apologise for any errors or omissions. Readers should feel free to e-mail any

More information

OPERATING INSTRUCTIONS FOR SYLVANIA. Type I08 Cathode-Ray Oscilloscope. Sylvania Electric Products Inc. Industrial Apparatus. Emporium, Pennsylvania

OPERATING INSTRUCTIONS FOR SYLVANIA. Type I08 Cathode-Ray Oscilloscope. Sylvania Electric Products Inc. Industrial Apparatus. Emporium, Pennsylvania OPERATING INSTRUCTIONS FOR SYLVANIA Type I08 Cathode-Ray Oscilloscope Sylvania Electric Products Inc. Industrial Apparatus Plant Emporium, Pennsylvania OPERATING INSTRUCTIONS FOR Sylvania Type 08 Cathode-Ray

More information

MODEL PA II-R (1995-MSRP $549.00)

MODEL PA II-R (1995-MSRP $549.00) F O R T H E L O V E O F M U S I C MODEL PA II-R (1995-MSRP $549.00) OWNER'S MANUAL AND INSTALLATION GUIDE INTRODUCTION To aid in the exciting and custom installs which installers are performing all over

More information

Revision 1.2d

Revision 1.2d Specifications subject to change without notice 0 of 16 Universal Encoder Checker Universal Encoder Checker...1 Description...2 Components...2 Encoder Checker and Adapter Connections...2 Warning: High

More information

Noise Detector ND-1 Operating Manual

Noise Detector ND-1 Operating Manual Noise Detector ND-1 Operating Manual SPECTRADYNAMICS, INC 1849 Cherry St. Unit 2 Louisville, CO 80027 Phone: (303) 665-1852 Fax: (303) 604-6088 Table of Contents ND-1 Description...... 3 Safety and Preparation

More information

RD RACK MOUNT DIMMER OWNERS MANUAL VERSION /09/2011

RD RACK MOUNT DIMMER OWNERS MANUAL VERSION /09/2011 RD - 122 RACK MOUNT DIMMER OWNERS MANUAL VERSION 1.3 03/09/2011 Page 2 of 14 TABLE OF CONTENTS UNIT DESCRIPTION AND FUNCTIONS 3 POWER REQUIREMENTS 3 INSTALLATION 3 PLACEMENT 3 POWER CONNECTIONS 3 OUTPUT

More information

Standard signal metering in wall-mounting case

Standard signal metering in wall-mounting case User manual AKV-2VR4C Standard signal metering in wall-mounting case Technical features: Digit height: 20 mm Colour: red Range of display: -999 9999 Wall-mounting case: black, made of ABS-plastic Protection

More information

(Cat. No IJ, -IK)

(Cat. No IJ, -IK) (Cat. No. 1771-IJ, -IK) Product Data The Encoder/Counter Module Assembly (cat. no. 1771-IJ or 1771-IK) maintains a count, independent of the processor, of input pulses that may typically originate from

More information

LM MHz RGB Video Amplifier System with OSD

LM MHz RGB Video Amplifier System with OSD LM1279 110 MHz RGB Video Amplifier System with OSD General Description The LM1279 is a full featured and low cost video amplifier with OSD (On Screen Display). 8V operation for low power and increased

More information

Data Acquisition Using LabVIEW

Data Acquisition Using LabVIEW Experiment-0 Data Acquisition Using LabVIEW Introduction The objectives of this experiment are to become acquainted with using computer-conrolled instrumentation for data acquisition. LabVIEW, a program

More information

Table of Contents. Read This First.2. Introduction by Jim Fosgate...3. Unpacking..4. Tubes and Tube shield Installation 5. Product Placement...

Table of Contents. Read This First.2. Introduction by Jim Fosgate...3. Unpacking..4. Tubes and Tube shield Installation 5. Product Placement... Owner s Manual Table of Contents Read This First.2 Introduction by Jim Fosgate...3 Unpacking..4 Tubes and Tube shield Installation 5 Product Placement...6 Connecting your Fosgate Signature..7 Phono stage

More information

Lab 7: Soldering - Traffic Light Controller ReadMeFirst

Lab 7: Soldering - Traffic Light Controller ReadMeFirst Lab 7: Soldering - Traffic Light Controller ReadMeFirst Lab Summary The two-way traffic light controller provides you with a quick project to learn basic soldering skills. Grading for the project has been

More information

Analog Circuits Prof. Nagendra Krishnapura Department of Electrical Engineering Indian Institute of Technology, Madras. Module - 04 Lecture 12

Analog Circuits Prof. Nagendra Krishnapura Department of Electrical Engineering Indian Institute of Technology, Madras. Module - 04 Lecture 12 Analog Circuits Prof. Nagendra Krishnapura Department of Electrical Engineering Indian Institute of Technology, Madras Module - 04 Lecture 12 So, far we have discussed common source amplifier using an

More information

MATE3 Owner s Manual Addendum

MATE3 Owner s Manual Addendum Purpose MATE3 Owner s Manual Addendum This document is an addendum to 900-0117-01-00, Revision C of the MATE3 System Display and Controller Owner s Manual. It provides descriptions of changes to the MATE3

More information

ECB DIGITAL ELECTRONICS PROJECT BASED LEARNING PROJECT REPORT ON 7 SEGMENT DIGITAL STOP WATCH USING DECODER

ECB DIGITAL ELECTRONICS PROJECT BASED LEARNING PROJECT REPORT ON 7 SEGMENT DIGITAL STOP WATCH USING DECODER ECB2212 - DIGITAL ELECTRONICS PROJECT BASED LEARNING PROJECT REPORT ON 7 SEGMENT DIGITAL STOP WATCH USING DECODER SUBMITTED BY ASHRAF HUSSAIN (160051601105) S SAMIULLAH (160051601059) CONTENTS >AIM >INTRODUCTION

More information

Signal Conditioners. Highlights. Battery powered. Line powered. Multi-purpose. Modular-style. Multi-channel. Charge & impedance converters

Signal Conditioners. Highlights. Battery powered. Line powered. Multi-purpose. Modular-style. Multi-channel. Charge & impedance converters Signal Conditioners Highlights Battery powered Line powered Multi-purpose Modular-style Multi-channel Charge & impedance converters Industrial charge amplifiers & sensor simulators PCB Piezotronics, Inc.

More information

Video Streamer Modifications

Video Streamer Modifications CB Electronics Video Streamer Modifications CB Electronics Loddonside, Lands End House, Beggars Hill Road, Charvil, Berks RG10 0UD, UK Tel: +44 (0)118 9320345, Fax: +44 (0)118 9320346 URL: www.colinbroad.com

More information

K800 RF AMPLIFIER TUBE UPGRADE

K800 RF AMPLIFIER TUBE UPGRADE R. F. Note 107 John Vincent August 5, 1988 K800 RF AMPLIFIER TUBE UPGRADE Contents: 1. Introduction 2. RCA 4648 Operating Experience and Evaluation. 3. Tube Selection Criteria 4. Cost and Availability

More information

W0EB/W2CTX DSP Audio Filter Operating Manual V1.12

W0EB/W2CTX DSP Audio Filter Operating Manual V1.12 W0EB/W2CTX DSP Audio Filter Operating Manual V1.12 Manual and photographs Copyright W0EB/W2CTX, March 13, 2019. This document may be freely copied and distributed so long as no changes are made and the

More information

A FOUR GAIN READOUT INTEGRATED CIRCUIT : FRIC 96_1

A FOUR GAIN READOUT INTEGRATED CIRCUIT : FRIC 96_1 A FOUR GAIN READOUT INTEGRATED CIRCUIT : FRIC 96_1 J. M. Bussat 1, G. Bohner 1, O. Rossetto 2, D. Dzahini 2, J. Lecoq 1, J. Pouxe 2, J. Colas 1, (1) L. A. P. P. Annecy-le-vieux, France (2) I. S. N. Grenoble,

More information

Reaction Game Kit MitchElectronics 2019

Reaction Game Kit MitchElectronics 2019 Reaction Game Kit MitchElectronics 2019 www.mitchelectronics.co.uk CONTENTS Schematic 3 How It Works 4 Materials 6 Construction 8 Important Information 9 Page 2 SCHEMATIC Page 3 SCHEMATIC EXPLANATION The

More information

CLOCKAUDIO. MR88 Automatic Microphone Mixer. Version 4.2

CLOCKAUDIO. MR88 Automatic Microphone Mixer. Version 4.2 CLOCKAUDIO MR88 Automatic Microphone Mixer Version 4.2 Clockaudio Limited,22 Arnside Road WATERLOOVILLE Hampshire. UK Tel : +44 (0)2392 251193 Fax : +44 (0)2392 251201 Email : sales@clockaudio.co.uk CONTENTS

More information

CHAPTER 9. Actives Devices: Diodes, Transistors,Tubes

CHAPTER 9. Actives Devices: Diodes, Transistors,Tubes CHAPTER 9 Actives Devices: Diodes, Transistors,Tubes 1 The electrodes of a semiconductor diode are known as anode and cathode. In a semiconductor diode, electrons flow from cathode to anode. In order for

More information

SUBCARRIER TRANSFER FILTER INSTRUCTION BOOK IB622702

SUBCARRIER TRANSFER FILTER INSTRUCTION BOOK IB622702 SCF611S SUBCARRIER TRANSFER FILTER INSTRUCTION BOOK IB622702 SCF611S SUBCARRIER TRANSFER FILTER TABLE OF CONTENTS PAGE SHIPPING INSPECTION 2 MODULE CONFIGURATION 2 INSTALLING MODULES 2-3 CABLING 3 FRONT

More information

AES-402 Automatic Digital Audio Switcher/DA/Digital to Analog Converter

AES-402 Automatic Digital Audio Switcher/DA/Digital to Analog Converter Broadcast Devices, Inc. AES-402 Automatic Digital Audio Switcher/DA/Digital to Analog Converter Technical Reference Manual Broadcast Devices, Inc. Tel. (914) 737-5032 Fax. (914) 736-6916 World Wide Web:

More information

STX Stairs lighting controller.

STX Stairs lighting controller. Stairs lighting controller STX-1795 The STX-1795 controller serves for a dynamic control of the lighting of stairs. The lighting is switched on for consecutive steps, upwards or downwards, depending on

More information

GATES AMPLIFIERS. Plug -in. Audio. Solid- Statesman Series HARRIS INTERTYPE CORPORATION. Six Premium Quality Transistorized Products

GATES AMPLIFIERS. Plug -in. Audio. Solid- Statesman Series HARRIS INTERTYPE CORPORATION. Six Premium Quality Transistorized Products Six Premium Quality Transistorized Products 6300 Series Solid- Statesman Audio HARRIS INTERTYPE CORPORATION GATES AMPLIFIERS THE GATES M -6337 TELEVISION AUDIO CON- TROL CONSOLE marks a significant advance

More information

CR7000. CRT Analyzer & Restorer. Easily Test And Restore CRTs With The Most Complete Tests Available For Added Profit And Security.

CR7000. CRT Analyzer & Restorer. Easily Test And Restore CRTs With The Most Complete Tests Available For Added Profit And Security. CR7000 CRT Analyzer & Restorer Easily Test And Restore CRTs With The Most Complete Tests Available For Added Profit And Security. S1 New Demands From Higher Performance CRTs Require New Analyzing Techniques

More information

COMPOSITE VIDEO LUMINANCE METER MODEL VLM-40 LUMINANCE MODEL VLM-40 NTSC TECHNICAL INSTRUCTION MANUAL

COMPOSITE VIDEO LUMINANCE METER MODEL VLM-40 LUMINANCE MODEL VLM-40 NTSC TECHNICAL INSTRUCTION MANUAL COMPOSITE VIDEO METER MODEL VLM- COMPOSITE VIDEO METER MODEL VLM- NTSC TECHNICAL INSTRUCTION MANUAL VLM- NTSC TECHNICAL INSTRUCTION MANUAL INTRODUCTION EASY-TO-USE VIDEO LEVEL METER... SIMULTANEOUS DISPLAY...

More information

OWNERS MANUAL. Revision /29/ Lightronics Inc. 509 Central Drive Virginia Beach, VA Tel

OWNERS MANUAL. Revision /29/ Lightronics Inc. 509 Central Drive Virginia Beach, VA Tel OWNERS MANUAL Revision 1.87 01/29/2006 Page 2 of 17 TABLE OF CONTENTS AR-1202 UNIT DESCRIPTION 3 EXTERNAL CONTROLS 3 POWER REQUIREMENTS 3 INSTALLATION 3 Physical Location 3 Power Input Connections 3 Three

More information

Manual Addendum For Rerun V1.1 software 12/12/2006, RERUN-A = Serial #06A068, RERUN-P = Serial #06A031

Manual Addendum For Rerun V1.1 software 12/12/2006, RERUN-A = Serial #06A068, RERUN-P = Serial #06A031 Manual Addendum For Rerun V1.1 software 12/12/2006, RERUN-A = Serial #06A068, RERUN-P = Serial #06A031 The Rerun product manual was written for V1.0 software. The new release, V1.1, adds a number of new

More information

Standby...For the Truth

Standby...For the Truth Innovation. Amplified. Chapter 6 Standby...For the Truth by Hartley Peavey Standby for the Truth Incredibly, very few modern technicians (and even fewer players) understand why so-called standby switches

More information

210E - 210ECL ECL ECL

210E - 210ECL ECL ECL 210E - 210ECL - 2010ECL - 2018ECL RMS Signal Monitor Operations Manual THIS MANUAL CONTAINS TECHNICAL INFORMATION FOR THE FOLLOWING SERIES OF MODEL 210/2010/2018 SIGNAL MONITORS, PCB Issue G: 210E, 210ECL,

More information

560A 500 SERIES COMPRESSOR/LIMITER OWNER S MANUAL

560A 500 SERIES COMPRESSOR/LIMITER OWNER S MANUAL 500 SERIES COMPRESSOR/LIMITER OWNER S MANUAL Warranty 1. Please register your product online at www.dbxpro.com. Proof-of-purchase is considered to be the responsibility of the consumer. A copy of the original

More information

Azatrax Model Railroad Track Signal Control - Single Track

Azatrax Model Railroad Track Signal Control - Single Track Installation Guide Azatrax Model Railroad Track Signal Control - Single Track TS2 What it is: The TS2 operates one or two trackside block signals (one in each direction) on one track to simulate the block

More information

Build A Video Switcher

Build A Video Switcher Build A Video Switcher VIDEOSISTEMAS serviciotecnico@videosistemas.com www.videosistemas.com Reprinted with permission from Electronics Now Magazine September 1997 issue Copyright Gernsback Publications,

More information