(1) Home Theatre System. Operating Instructions HT-SS Sony Corporation

Transcription

1 (1) Home Theatre System Operating Instructions HT-SS Sony Corporation

2 WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To reduce the risk of fire, do not cover the ventilation opening of the apparatus with newspapers, tablecloths, curtains, etc. Do not place the naked flame sources such as lighted candles on the apparatus. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To reduce the risk of fire or electric shock, do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such as vases, on the apparatus. As the main plug is used to disconnect the unit from the mains, connect the unit to an easily accessible AC outlet. Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately. Do not expose batteries or apparatus with batteryinstalled to excessive heat such as sunshine, fire or the like. The unit is not disconnected from the mains as long as it is connected to the AC outlet, even if the unit itself has been turned off. To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. For customers in the United States, Canada and Mexico This symbol is intended to alert the user to the presence of the Hot Surface that may be hot if it is touched during the normal operation. For customers in the United States Owner s Record The model and serial numbers are located on the rear of the unit. Record these numbers in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. Serial No. ENERGY STAR is a U.S. registered mark. As an ENERGY STAR partner, Sony Corporation has determined that this product meets the ENERGY STAR guidelines for energy efficiency. This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 2 US

3 10)Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11)Only use attachments/accessories specified by the manufacturer. 12)Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13)Unplug this apparatus during lightning storms or when unused for long periods of time. 14)Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. The following FCC statement applies only to the version of this model manufactured for sale in the U.S.A. Other versions may not comply with FCC technical regulations. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. CAUTION You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. To reduce the risk of electric shock, the speaker cord should be connected to the apparatus and the speakers in accordance with the following instructions. 1) Disconnect the AC power cord from the MAINS. 2) Strip 10 to 15 mm of the wire insulation of the speaker cord. 3) Connect the speaker cord to the apparatus and the speakers carefully so as not to touch the core of speaker cord by hand. Also disconnect the AC power cord from the MAINS before disconnecting the speaker cord from the apparatus and the speakers. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 3 US

4 About This Manual The instructions in this manual are for model HT-SS360. In this manual, models of area code U is used for illustration purposes unless stated otherwise. Any difference in operation is clearly indicated in the text, for example, Models of area code CA only. The HT-SS360 consists of: Receiver STR-KS360 Speaker system a) Front speaker SS-MSP36S Center speaker SS-CNP36 Surround speaker SS-SRP36S Subwoofer SS-WP36 a) Be sure to use only the supplied speakers. The instructions in this manual describe the controls on the supplied remote. You can also use the controls on the receiver if they have the same or similar names as those on the remote. About area codes The area code of the receiver you purchased is shown on the lower portion of the rear panel (see the illustration below). On Copyrights This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS** Digital Surround System. * Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double- D symbol are trademarks of Dolby Laboratories. ** Manufactured under license under U.S. Patent # s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS and DTS Digital Surround are registered trademarks and the DTS logos and Symbol are trademarks of DTS, Inc DTS, Inc. All Rights Reserved. This receiver incorporates High-Definition Multimedia Interface (HDMI TM ) technology. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. x.v.color and x.v.color logo are trademarks of Sony Corporation. BRAVIA is a trademarks of Sony Corporation. SPEAKERS FRONT R FRONT L SUR R SUR L CENTER SUBWOOFER Area code Any differences in operation, according to the area code, are clearly indicated in the text, for example, Models of area code AA only. 4 US

5 Table of Contents Description and location of parts... 6 Getting Started 1: Installing the speakers : Connecting the speakers : Connecting the TV : Connecting the audio/video components : Connecting the antennas : Preparing the receiver and the remote : Calibrating the appropriate settings automatically (AUTO CALIBRATION) : Adjusting the speaker levels (TEST TONE) Playback Selecting a component Enjoying sound/images from the components connected to the receiver Amplifier Operations Navigating through menus Settings for the HDMI (SET HDMI menu) Settings for the Auto Calibration (A.CAL menu) Settings for the Speaker (SP SETUP menu) Adjusting the level (LEVEL menu) Adjusting the tone (TONE menu) Settings for the Custom Menu (CUSTOM menu) Enjoying Surround Sound Selecting the sound field Tuner Operations Listening to FM/AM radio...38 Presetting radio stations...39 Using BRAVIA Sync features What is BRAVIA Sync?...41 Preparing for the BRAVIA Sync...42 Playing back components with one-touch operation (One-Touch Play)...43 Enjoying the TV sound from the speakers connected to the receiver (System Audio Control)...44 Turning off the receiver with the TV (System Power Off)...45 Using the Power Saving function (Power Save)...45 Other Operations Changing the brightness of the display (DIMMER)...46 Changing the display setting (DISPLAY)...47 Using the Sleep Timer (SLEEP)...47 Switching between digital and analog audio (IN MODE)...48 Using the Remote Changing the input button assignments...48 Additional Information Glossary...49 Precautions...51 Troubleshooting...52 Specifications...56 Index US

6 Description and location of parts Front panel ?/1 INPUT SELECTOR MASTER VOLUME ACTIVE STANDBY Name A?/1 (on/standby) B ACTIVE STANDBY lamp C Display D White lamp E Remote sensor F MASTER VOLUME G INPUT SELECTOR Function Press to turn the receiver on or off (page 21, 28, 29). Lights up in amber when the Control for HDMI is set to on and the receiver is on standby mode. Note If the ACTIVE STANDBY lamp is flashing, see page 55. The current status of the selected component or a list of selectable items appears here (page 7). Lights up when the receiver is on and DSPL is set to on in DISPLAY function (page 47). Lights off when the receiver is in standby mode or DSPL is set to off in DISPLAY function. Receives signals from remote commander. Turn to adjust the volume level of all speakers at the same time (page 27, 28, 29). Press to select the input source to playback (page 27, 28, 29, 38, 39). 6 US

7 Indicators on the display qs qa q; Name A LFE B SLEEP C Playback channel indicators L R C SL SR S Function Lights up when the disc being played back contains an LFE (Low Frequency Effect) channel and the LFE channel signal is actually being reproduced. Lights up when the sleep timer is activated (page 47). The letters (L, C, R, etc.) indicate the channels being played back. The boxes around the letters vary to show how the receiver downmixes the source sound. Front Left Front Right Center (monaural) Surround Left Surround Right Surround (monaural or the surround components obtained by Pro Logic processing) Example: Recording format (Front/ Surround): 3/2.1 Sound Field: A.F.D. AUTO D D Lights up when receiver is decoding Dolby Digital signals. Note When playing a Dolby Digital format disc, be sure that you have made digital connections. E HDMI SW L C R SL SR Lights up when a playback component is connected to this receiver using an HDMI jack (page 18). Name F Preset station indicators G Tuner indicators H COAX I OPT J PL/ PLII K DTS L SW Function Lights up when using the receiver to tune in radio stations you have preset. For details on presetting radio stations, see page 39. Lights up when using the receiver to tune in radio stations (page 38), etc. Lights up when the source signal is a digital signal being input through the COAX IN jack. Lights up when the source signal is a digital signal being input through the OPT IN jack. PL lights up when the receiver applies Pro Logic processing to 2 channel signals in order to output the center and surround channel signals. PLII lights up when the Pro Logic II Movie/Music decoder is activated. Lights up when the receiver is decoding DTS signals. Note When playing a DTS format disc, be sure that you have made digital connections. Lights up when the audio signal is output from the SUBWOOFER jack. 7 US

8 Rear panel L L DIGITAL TV ANTENNA SPEAKERS R R AUTO AUDIO IN AUDIO IN AUDIO IN COAX IN CAL MIC VIDEO 1 TV SA-CD/CD VIDEO 2 OPT IN SAT OPT IN AM DC5V 700mA MAX HDMI FRONT R FRONT L SUR R SUR L CENTER SUBWOOFER DMPORT BD IN DVD IN SAT IN OUT A SPEAKERS section B DMPORT Connects to the supplied speakers and subwoofer (page 15). DMPORT jack Connects to a DIGITAL MEDIA PORT adapter (page 17). C AUTO CALIBRATION section AUTO CAL MIC jack Connects to the supplied optimizer microphone for the Auto Calibration function (page 23). E DIGITAL INPUT/OUTPUT section OPT IN jacks Connects to a DVD player, etc. The COAX IN jack HDMI IN/ OUT jacks COAX IN jack provides a better sound quality (page 20). Connects to a DVD player, satellite tuner, or a Blu-ray disc player. The image is output to a TV or a projector while the sound can be output from a TV or/and speakers connected to this receiver (page 18). D AUDIO INPUT section White (L) Red (R) AUDIO IN jacks Connects to a Super Audio CD player, CD player, etc. (page 17, 20). F ANTENNA section FM ANTENNA jack AM ANTENNA terminals Connects to the supplied FM wire antenna (page 21). Connects to the supplied AM loop antenna (page 21). 8 US

9 Remote commander You can use the supplied remote RM-AAU057 to operate the receiver and to control the Sony audio/video components that the remote is assigned to operate (page 48). RM-AAU057 ws wa w; ql qk qj qh qg TV INPUT DMPORT SYSTEM STANDBY VIDEO1 VIDEO2 BD DVD SAT BD/DVD TOP MENU MENU CLEAR DISPLAY 9 AMP MENU 0 ENTER RETURN/EXIT TV CH MENU/HOME TV CH + PRESET REPLAY ADVANCE PRESET +. < > TUNING TUNING + TV TV SA-CD/CD TUNER F1?/1 F2 JUMP PICTURE WIDE FAVORITES THEATER m TV?/1 AV?/1 TOOLS/ OPTIONS H X < GUIDE MUTING TV VOL MASTER VOL M x q; qa qs qd qf Basic operations Remote Button B?/1 (on/standby) Function Press to turn the receiver on or off. To turn off all Sony components, press?/1 and AV?/1 (A) at the same time (SYSTEM STANDBY). Saving the power in standby mode When CONTROL FOR HDMI is set to CTRL ON and P.SAVE is set to SAVE ON (page 33). C Input buttons Press one of the buttons to select the component you want to use. The buttons are factory assigned to control Sony components. You can change the button assignments following the steps in Changing the input button assignments on page 48. G SOUND FIELD Press to select a sound field. I AMP MENU K MUTING L MASTER VOL +*/ Q, V/v/B/b Press to display the menu of the receiver. Press to turn off the sound temporarily. Press MUTING again to restore the sound. Press to adjust the volume. Press V, v, B or b to select the settings. Then, press to enter the selection. continued 9 US

10 Tuner operations Remote Button H ENTER M MENU/HOME N PRESET +/ TUNING +/ Q, V/v/B/b R DISPLAY S CLEAR DMPORT operations Remote Button N./> m/m Function Press to enter the selection. Press to display the menu. Press to select a preset station. Press to scan the station. Press to select the menu items and to enter the selection. Press to display the information during Tuner function. Press to clear a mistake when you input a wrong character. Function Press to skip the track. Press to fast reverse or fast forward. H (playback)/ Play mode button. X (pause, press again to resume normal playback/ x (stop) To control the component 1 Press one of the input buttons C (TV, BD, DVD, or SAT) to select the component you want to operate. The component assigned to the selected input button becomes operable. 2 Referring to the following table, press the corresponding button for the operation. Common operations Remote Button A TV?/1 AV?/1 (on/standby) H ENTER T Numeric buttons (number 5*) Function Press to turn on or off the Sony audio/video components that the remote is assigned to operate (page 48). Press A?/1 and B TV?/1/AV?/1 at the same time to turn off the receiver and all other components that the remote is assigned to operate (SYSTEM STANDBY). Press to enter the selection. To control the TV Press and hold (O) TV (yellow) button while pressing the buttons with an yellow dot or yellow printing to control the TV. Remote Button D FAVORITES WIDE E THEATER F GUIDE J TOOLS/ OPTIONS Press to select channels and tracks directly. Function To display the stored favorite channel list of TV. To select the wide picture mode. Press to sets the optimal picture settings automatically for watching movies, when you connect a Sony TV which is compatible with the THEATER button. Also, the audio is automatically switched to the audio output of this receiver when you connect the TV and the receiver with HDMI connection, and the Control for HDMI function is set to on. Press to display the guide when you are watching analog and digital channels. Press to enable you to access various viewing options and change/make adjustments according to the source and screen format. 10 US

11 Remote Button K MUTING L TV +/ M MENU/HOME N TV CH +/ P RETURN/ EXIT Q, V/v/B/b R DISPLAY S T Numeric buttons (number 5*) U JUMP PICTURE V TV INPUT Function Press to turn off the sound. Press to adjust the volume. Press to allow you to select channels or input sources and change the settings for your TV. Selects the next (+) or previous ( ) channel. To scan quickly through channels, press and hold down either +/. Press to return to the previous screen of any displayed menu. Press to select the menu item and enters the selection. Display the TV s information on the TV screen. (Displays the current channel number, etc.) Selects digital channels using with the 0-9 and ENTER buttons. For example, to enter 2.1, press 2,, 1 and ENTER. Press to select channels. Press ENTER (H) to change channels immediately. Press to select the previous and the current channels of the TV, Satellite tuner, Bluray disc recorder, DVD player. Press to cycle through the available picture modes of the TV. Press to select input. To control the DVD recorder/blu-ray Disc recorder Remote Button D F1 F2 M MENU/HOME N. < < Function Press to select the HDD. Press to select the Blu-ray Disc/DVD. Press to display the menu. Press to skip chapters. Press to jump backward while viewing live or recorded programs. Press to jump forward while viewing recorded programs. > Press to skip forward to the next available chapter. m/m Press to fast reverse or to fast forward the disc when pressed during playback. H* (playback)/ Play mode button. X (pause, press again to resume normal playback/ x (stop) Q, V/v/B/b U BD/DVD TOP MENU, MENU Press to select a menu item and enters the selection. Press to display the top menu or disc menu. continued 11 US

12 To control the DVD player/ Blu-ray Disc player Remote Button M MENU/HOME N./> REPLAY < ADVANCE m/m Function Press to display the menu. Press to skip chapters. Press to jump backward. Press to jump forward. Press to fast reverse or to fast forward the disc when pressed during playback. H* (playback)/ Play mode button. X (pause, press again to resume normal playback/ x (stop) Q, V/v/B/b U BD/DVD TOP MENU, MENU < Press to select a menu item and enters the selection. Press to display the top menu or disc menu. To control the SAT Remote Button F GUIDE M MENU/HOME Q, V/v/B/b Function Press to display the guide menu. Press to display the menu. Press to select a menu item and enters the selection. * The number 5, MASTER VOL + and H buttons have tactile dots. Use the tactile dots as references when operating the receiver. Notes Some functions explained in this section may not work depending on the model. The above explanation is intended to serve as an example only. Therefore, depending on the component, the above operation may not be possible or may operate differently than described. To control the HDD/DVD COMBO Remote Button D F1 F2 M MENU/HOME N./> < < Function Press to select the HDD. Press to select the DVD. Press to display the menu. Press to specify the previous/next chapter/track. Press to change to replay mode. Press to advance. m/m Press to fast reverse or to fast forward the disc when pressed during playback. H* (playback)/ Play mode button. X (pause, press again to resume normal playback/ x (stop) Q, V/v/B/b U BD/DVD TOP MENU, MENU Press to move the highlight (cursor) and selects the item. Press to display the top menu or disc menu. 12 US

13 Getting Started 1: Installing the speakers This receiver allows you to use a 5.1 channel speaker system. To fully enjoy theater-like multi channel surround sound, be sure to connect all the speakers (two front speakers, a center speaker, and two surround speakers) and a subwoofer (5.1 channel). You can place your speakers as shown below. AFront speaker (left) BFront speaker (right) CCenter speaker DSurround speaker (left) ESurround speaker (right) FSubwoofer Installing the speakers on a flat surface Before you install the speaker and subwoofer, be sure to attach the supplied foot pads to prevent vibration or movement as shown in the illustration below. Example of front speaker Getting Started Installing the speakers on the speaker stand For greater flexibility in positioning the speakers, use the optional WS-FV11 or WS-FV10D speaker stand (available only in certain countries). For details, refer to the operating instructions supplied with the speaker stand. Tip Since the subwoofer does not emit highly directional signals, you can place it wherever you want. 13 US

14 Installing the speakers on the wall You can install your speakers on the wall. 1 Prepare screws (not supplied) that are suitable for the hook on the back of each speaker. See the illustrations below. 3 Hang the speakers on the screws. 4.6 mm (3/16 inch) 10 mm (13/32 inch) 4 mm (3/16 inch) more than 25 mm (more than 1 inch) 4.6 mm (3/16 inch) 10 mm (13/32 inch) Hook on the back of the speaker 2 Fasten the screws to the wall. The screws should protrude 7/32 to 9/32 inch. For the center speaker 160 mm (6 5/16 inches) Rear of speaker Notes Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach the screws securely to a beam and fasten them to the wall. Install the speakers on a vertical and flat wall where reinforcement is applied. Contact a screw shop or installer regarding the wall material or screws to be used. Sony is not responsible for accident or damage caused by improper installation, insufficient wall strength or improper screw installation, natural calamity, etc. 5 mm to 7 mm (7/32 to 9/32 inch) For the front speakers and surround speakers 5 mm to 7 mm (7/32 to 9/32 inch) 14 US

15 2: Connecting the speakers Before connecting the cords, be sure to disconnect the AC power cord (mains lead). B A C F Note on speaker cords The connector of the speaker cords are the same color as the speaker jack to be connected. When connecting a speaker cord, be sure to match the colored connector to the speaker jack on the receiver: Connector Red White Grey Blue Green Purple Speaker jack FRONT R FRONT L SUR R SUR L CENTER SUBWOOFER Getting Started Connector A FRONT R SPEAKERS FRONT L SUR R SUR L CENTER SUBWOOFER A To connect the speakers correctly Check the speaker type by referring to the speaker label* at the rear panel of the speakers. Character on speaker label L R SL SR Speaker type Front left Front right Surround left Surround right * The center speaker and subwoofer do not have the character on the speaker label. For details on the speaker type, see page 4. A E D A Speaker cord (supplied) AFront speaker (left) BFront speaker (right) CCenter speaker DSurround speaker (left) ESurround speaker (right) FSubwoofer 15 US

16 3: Connecting the TV You can watch the selected input image when you connect the HDMI OUT jack to a TV. It is not necessary to connect all the cords. Connect audio and video cords according to the jacks of your components. Before connecting the cords, be sure to disconnect the AC power cord. Tips To output the sound of the TV from the speakers connected to the receiver, be sure to connect the audio output jacks of the TV to the TV IN jacks of the receiver. turn off the TV s volume or activate the TV s muting function. All the digital audio jacks are compatible with 32 khz, 44.1 khz, 48 khz, and 96 khz sampling frequencies. TV Audio signal Audio/video signal A B C L L DIGITAL TV ANTENNA R R AUDIO IN AUDIO IN AUDIO IN COAX IN VIDEO 1 TV SA-CD/CD VIDEO 2 OPT IN SAT OPT IN AM ma MAX HDMI RT BD IN DVD IN SAT IN OUT A Audio cord (not supplied) B Optical digital cord (not supplied) C HDMI cable (not supplied) We recommend that you use a Sony HDMI cable. Notes Be sure to turn on the receiver when the video and audio signals of a playback component are being output to a TV via the receiver. Unless the power is turned on, neither video nor audio signals will be transmitted. When connecting optical digital cords, insert the plugs straight in until they click into place. Do not bend or tie optical digital cords. 16 US

17 4: Connecting the audio/ video components How to hook up your components This section describes how to hook up your components to this receiver. Before you begin, refer to Component to be connected below for the pages which describe how to connect the audio/video components. Before connecting the cords, be sure to disconnect the AC power cord (mains lead). After hooking up all your components, proceed to 5: Connecting the antennas (page 21). Connecting audio components The following illustration shows how to connect audio components such as Super Audio CD player or CD player and DIGITAL MEDIA PORT adapter. You can also view the images on the TV screen by connecting the video output of the DIGITAL MEDIA PORT adapter to the video input of the TV. Super Audio CD player, CD player A Audio signal Getting Started Component to be connected To connect See TV page 16 Audio components page 17 Super Audio CD player/ CD player DIGITAL MEDIA PORT adapter Components with HDMI jack page 18 Video components page 20 Satellite tuner, Set-top box DVD player, DVD recorder VCR DC5V L R R AUTO AUDIO IN AUDIO IN AUDIO IN COAX IN CAL MIC VIDEO 1 TV SA-CD/CD VIDEO 2 700mA MAX DMPORT HDMI L BD IN DIGITAL DVD IN OPT IN SAT SAT IN TV TV OPT IN A DIGITAL MEDIA PORT adapter B A Audio cord (not supplied) B Video cord (not supplied) * The type of connector varies depending on the DIGITAL MEDIA PORT adapter. For details, refer to the operating instructions supplied with the DIGITAL MEDIA PORT adapter. continued 17 US

18 Notes on connecting DIGITAL MEDIA PORT adapter Do not connect or disconnect the DIGITAL MEDIA PORT adapter while the receiver is turned on. Be sure to make DMPORT connections firmly, insert the connector straight in. As the connector of the DIGITAL MEDIA PORT adapter is fragile, be sure to handle with care when placing or moving the receiver. When connecting the DIGITAL MEDIA PORT adapter, be sure the connector is inserted with the arrow mark facing toward the arrow mark on the DMPORT jack. To detach the DIGITAL MEDIA PORT adapter, press and holed both sided of the connector and then pull out the connector. 2 1 DC5V 700mA MAX DMPORT 1 Connecting components with HDMI jacks HDMI is the abbreviated name for High- Definition Multimedia Interface. It is an interface which transmits video and audio signals in digital format. Sony recommends that you connect components to the receiver using an HDMI cable. With HDMI, you can easily enjoy both high quality sound and high quality images. However, it is necessary to connect the audio output of the TV to the audio input of the receiver using an optical cord to listen to the TV multi channel surround sound broadcasting from the receiver. By connecting Sony BRAVIA Sync compatible components using HDMI cables, BRAVIA Sync Features makes operations simpler (page 41). HDMI features A digital audio signals transmitted by HDMI can be output from the speakers connected to the receiver. This signal supports Dolby Digital, DTS and Linear PCM. This receiver supports xvycc transmission. This receiver supports the Control for HDMI function. For details, see Using BRAVIA Sync features (page 41). 18 US

19 R R AUDIO IN AUDIO IN AUDIO IN COAX IN VIDEO 1 TV SA-CD/CD VIDEO 2 ma MAX RT L HDMI L BD IN Audio/video signals Blu-ray disc player C DIGITAL DVD IN TV, etc. Audio signals OPT IN SAT OPT IN ANTENNA a) If you connect a DVD player, be sure to change the factory setting of the DVD button on the remote so that you can use the button to control your DVD player. For details, see Changing the input button assignments (page 48). b) Connect at least one of the audio cords (B or C). SAT IN A A A TV Audio/video signals DVD recorder/ DVD player a) B Audio/video signals OUT AM A Audio/video signals Satellite tuner/ Set-top box A HDMI cable (not supplied) We recommend that you use a Sony HDMI cable. B Optical digital cord (not supplied) b) C Audio cord (not supplied) b) Notes on HDMI connections An audio signal input to the HDMI IN jack is output from the SPEAKERS jacks and HDMI OUT jack. It is not output from any other audio jacks. Video signals input to the HDMI IN jack can only be output from the HDMI OUT jack. The multi/stereo area audio signals of a Super Audio CD are not output. Audio signals (sampling frequency, bit length, etc.) transmitted from an HDMI jack may be suppressed by the connected component. Check the setup of the connected component if the image is poor or the sound does not come out of a component connected via the HDMI cable. Sound may be interrupted when the sampling frequency, the number of channels or the audio format of the audio output signals from the playback component is switched. When the connected component is not compatible with copyright protection technology (HDCP), the image and/or the sound from the HDMI OUT jack may be distorted or may not be output. In this case, check the specification of the connected component. You can enjoy multi channel Linear PCM only with an HDMI connection. Set the image resolution of the playback component to 720p, 1080i or 1080p when you output 96 khz multi channel sound over an HDMI connection. You may need to make certain settings on the image resolution of the player before you can enjoy multi channel Linear PCM. Refer to the operating instructions of the player. Refer to the operating instructions of each component connected for details. We do not recommend using an HDMI-DVI conversion cable. When you connect an HDMI-DVI conversion cable to a DVI-D component, the sound and/or the image may not be output. Getting Started 19 US

20 Connecting video components The following illustration shows how to connect video components such as DVD player, DVD recorder, VCR, etc. It is not necessary to connect all the cords. Connect audio and video cords according to the jacks of your components. DVD recorder, DVD player Audio signals Satellite tuner, Set-top box Audio signals Notes To input multi channel digital audio from the DVD player, set the digital audio output setting on the DVD player. Refer to the operating instructions supplied with the DVD player. When connecting optical digital cords, insert the plugs straight in until they click into place. Do not bend or tie optical digital cords. Be sure to connect the video output of the DVD player, DVD recorder and VCR to the TV, so that the image is displayed on the TV. Refer to the operating instructions of each connected component for details. You cannot do recording on the DVD recorder or VCR via this receiver. For details, refer to the operating instructions supplied with the DVD recorder or VCR. B C Tip All the digital audio jacks are compatible with 32 khz, 44.1 khz, 48 khz, and 96 khz sampling frequencies. L L DIGITAL TV ANTENNA R R AUTO AUDIO IN AUDIO IN AUDIO IN CAL MIC VIDEO 1 TV SA-CD/CD COAX IN VIDEO 2 OPT IN SAT OPT IN AM DC5V 700mA MAX HDMI DMPORT BD IN DVD IN SAT IN OUT A Audio signal VCR A Audio cord (not supplied) B Coaxial digital cord (not supplied) C Optical digital cord (not supplied) 20 US

21 ?/1 ACTIVE STANDBY INPUT SELECTOR MASTER VOLUME 5: Connecting the antennas Connect the supplied AM loop antenna and FM wire antenna. Before connecting the antennas, be sure to disconnect the AC power cord (mains lead). FM wire antenna (supplied) 6: Preparing the receiver and the remote Connecting the AC power cord (mains lead) Connect the AC power cord (mains lead) to a wall outlet. Getting Started AM loop antenna (supplied) AC power cord (mains lead) L L DIGITAL TV ANTENNA SPEAKERS R R AUDIO IN AUDIO IN AUDIO IN COAX IN VIDEO 1 TV SA-CD/CD VIDEO 2 OPT IN SAT OPT IN AM FRONT R FRONT L SUR R SUR L CENTER ma MAX HDMI RT BD IN DVD IN SAT IN OUT To the wall outlet * The shape of the connector varies depending on the area code of this receiver. Notes To prevent noise pickup, keep the AM loop antenna away from the receiver and other components. Be sure to fully extend the FM wire antenna. After connecting the FM wire antenna, keep it as horizontal as possible. Performing initial setup operations Before using the receiver for the first time, initialize the receiver by performing the following procedure. This procedure can also be used to return settings you have made to their factory defaults. Be sure to use the buttons on the receiver for this operation. 1,2 1 Press?/1 to turn on the receiver. 2 Hold down?/1 for 5 seconds. CLEARED appears. All the settings you have changed or adjusted are reset to the initial settings. 21 US

22 Inserting batteries into the remote Insert two R6 (size-aa) batteries in the RM-AAU057 Remote Commander. Observe the correct polarity when installing batteries. Notes Do not leave the remote in an extremely hot or humid place. Do not use a new battery with old ones. Do not mix manganese batteries and other kinds of batteries. Do not expose the remote sensor to direct sunlight or lighting apparatuses. Doing so may cause a malfunction. If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. When you replace the batteries, the remote buttons may be reset to their factory settings. If this happens, reassign the buttons again (page 48). When the remote no longer operates the receiver, replace all the batteries with new ones. 7: Calibrating the appropriate settings automatically (AUTO CALIBRATION) This receiver is equipped with DCAC (Digital Cinema Auto Calibration) Technology which allows you to perform automatic calibration as follows: Check the connection between each speaker and the receiver. Adjust the speaker level. Measure the distance of each speaker from your listening position. Measure the frequency characteristics.* * The measurement result is not utilized for signals with a sampling frequency of more than 96 khz. The DCAC is designed to obtain proper sound balance in your room. However, you can adjust the speaker levels manually according to your preference. For details, see 8: Adjusting the speaker levels (TEST TONE) (page 26). 22 US

23 SPEAKERS FRONT R FRONT L SUR R SUR L CENTER SUBWOOFER L L DIGITAL R R AUTO AUDIO IN AUDIO IN AUDIO IN COAX IN OPT IN OPT IN CAL MIC VIDEO 1 TV SA-CD/CD VIDEO 2 SAT DC5V 700mA MAX HDMI BD IN DVD IN SAT IN DMPORT TV ANTENNA OUT AM Before you perform Auto Calibration Before you perform the Auto Calibration, set up and connect the speakers (page 13, 15). The AUTO CAL MIC jack is used for the supplied optimizer microphone only. Do not connect other microphones to this jack. Doing so may damage the receiver and the microphone. During the calibration, the sound that comes out of the speakers is very loud. The volume of the sound cannot be adjusted. Pay attention to the presence of children or to the effect on your neighborhood. Perform the Auto Calibration in a quiet environment to avoid the effect of noise and to get a more accurate measurement. If there are any obstacles in the path between the optimizer microphone and the speakers, the calibration cannot be performed correctly. Remove any obstacles from the measurement area to avoid measurement error. Note If the muting function has been activated before you perform Auto Calibration, the muting function will be set to off automatically. Optimizer microphone 1 Connect the supplied optimizer microphone to the AUTO CAL MIC jack. 2 Set up the optimizer microphone. Place the optimizer microphone at your listening position.you can also use a stool or tripod so that the optimizer microphone remains at the same height as your ears. Tip When you face the speaker towards the optimizer microphone, you will get a more accurate measurement. Performing Auto Calibration,V,v,B,b TV INPUT DMPORT SYSTEM STANDBY VIDEO1 VIDEO2 BD DVD SAT BD/DVD TOP MENU MENU CLEAR DISPLAY TV TV?/1 AV?/1 SA-CD/CD TUNER F1 9 F2 JUMP PICTURE WIDE FAVORITES THEATER SOUND FIELD AMP MENU 0 ENTER TOOLS/ OPTIONS?/1 GUIDE MUTING TV VOL MASTER VOL?/1 switch Input buttons AMP MENU MUTING MASTER VOL +/ Getting Started RETURN/EXIT MENU/HOME 1 Press AMP MENU. 2 Press V/v repeatedly to select A.CAL. 3 Press or b to enter the menu. START appears on the display. continued 23 US

24 4 Press to start the measurement. Measurement starts in 5 seconds. While the time is counting down, stand away from the measurement area to avoid measurement error. The measurement process will take approximately 30 seconds to complete. The table below shows the display when measurement starts. Measurement for Speaker existance Speaker gain, distance, frequency response Subwoofer gain and distance Display TONE T.S.P. WOOFER Note If CHK MIC appears, you cannot perform the Auto Calibration. Connect the calibration mic, then restart the Auto Calibration. Tips When Auto Calibration starts: Stand some distance from the speakers and the listening position to avoid measurement failure. This is because test signals are output from the speakers during measurement. Avoid making noise to get a more accurate measurement. The Auto Calibration function will be canceled when you do the following during the measurement process: Press?/1 or MUTING. Press input buttons on the remote or INPUT SELECTOR on the receiver. Change the volume level. Confirming/saving the measurement results 1 Confirm the measurement result. When the measurement ends, a beep sounds and the measurement result appears on the display. Measurement result When the measurement process completes properly When the measurement process fails Display SAVE ERROR XXXX Explanation Proceed to step 2. See When error codes appear (page 25). 2 Press V/v repeatedly to select the item. Then, press. Item SAVE WRN CHK DIST LEVEL EXIT Explanation Saves the measurement results and exits the setting process. Displays warning concerning the measurement results. See When you select WRN CHK (page 25). Displays the measurement result for speaker distance. Displays the measurement result for speaker level. Exits the setting process without saving the measurement results. Note After SAVE is displayed for 50 seconds, the measurement result is saved automatically, without the need to save the procedure. 3 Save the measurement result. Select SAVE in step 2. The measurement results are saved. 24 US

25 When error codes appear Try the remedies and perform the Auto Calibration again. Error code ERROR 32 ERROR F 33 Cause and remedies The sound input from the optimizer microphone is out of the acceptable range. The optimizer microphone or subwoofer may be damaged. Contact your Sony dealer or local authorized Sony service facility. The front speakers are not connected. Check that the front speakers are connected properly. ERROR SR 33 Either the surround left or surround right speaker is not connected. Check that the surround speakers are connected properly. ERROR SW 33 The subwoofer may be damaged. Contact your Sony dealer or local authorized Sony service facility. When you select WRN CHK If a warning on the measurement result is present, detailed information is displayed. Press or B to return to step 2 of Confirming/saving the measurement results. Warning code Explanation WARN 40 The Auto Calibration has completed. However, the noise level is high. You may be able to perform the Auto Calibration properly if you try it again, even though the measurement cannot be performed in all environments. Try to perform the Auto Calibration in a quiet environment. WARN 41 WARN 42 The sound input from the optimizer microphone is out of the acceptable range. The distance between the optimizer microphone and the speakers is too closed. Set them away, and then try to perform the Auto Calibration. Warning code Explanation WARN 43 NO WARN The distance and position of a subwoofer cannot be detected. This may be caused by noise. Try to perform the Auto Calibration in a quiet environment. There is no warning information. When you select DIST or LEVEL You can check the speaker distance or speaker level. When you have finished Disconnect the optimizer microphone from the receiver. Note If you have changed the position of the speakers, it is recommended that you perform Auto Calibration again in order to enjoy the surround sound. Clearing the measurement result You can delete the result of Auto Calibration. If there is no saved data, you cannot delete the result. 1 Press AMP MENU. 2 Press V/v repeatedly until A.CAL appears, then press or b. 3 Press V/v repeatedly to select A.CAL CLR, then press or b. 4 Press V/v repeatedly to select YES, then press. The saved result is deleted. The settings for speaker distance and speaker level return to their defaults. Getting Started 25 US

26 8: Adjusting the speaker levels (TEST TONE) You can adjust the speaker levels while listening to the test tone from your listening position.,v,v,b,b CLEAR DISPLAY RETURN/EXIT AMP MENU 0 ENTER TOOLS/ OPTIONS MENU/HOME MUTING TV VOL MASTER VOL AMP MENU MASTER VOL +/ 1 Press AMP MENU. SET HDMI appears on the display. 2 Press V/v repeatedly until LEVEL appears, then press or b. 3 Press V/v repeatedly until T. TONE appears, then press or b. 4 Press V/v repeatedly to select T. TONE Y, then press. The test tone is output from each speaker in sequence as follows: Front left t Center t Front right t Surround right t Surround left t Subwoofer 5 Press V/v repeatedly to select the desired speaker, then press or b. The test tone is emitted from the speaker that is being adjusted only. FL LVL: adjusts the front left speaker level. CNT LVL: adjusts the center speaker level. FR LVL: adjusts the front right speaker level. SR LVL: adjusts the surround right speaker level. SL LVL: adjusts the surround left speaker level. SW LVL: adjusts the subwoofer level. Notes CNT LVL does not appear when you set CNT N in the SP SETUP setting. SR LVL and SL LVL do not appear when you set SUR N in the SP SETUP setting. 6 Press V/v to adjust the speaker level, then press or b. You can adjust from 6.0 db to +6.0 db in 0.5 db steps. Note If you do not adjust for a certain period, the test tone is emitted from the next speaker in sequence. 7 Repeat step 5 and 6 to adjust the speaker level. 8 After you have finished making adjustments, press V/v until T. TONE appears, then press or b. 9 Press V/v repeatedly to select T. TONE N, then press. 10Press AMP MENU. The AMP menu turns off. When a test tone is not output from the speakers The speaker cords may not be connected securely. The speaker cords may have the short-circuit problem. The test tone signals are not output from the HDMI OUT jack. 26 US

27 Playback Selecting a component TV INPUT DMPORT SYSTEM STANDBY VIDEO1 VIDEO2 BD DVD SAT BD/DVD TOP MENU MENU CLEAR DISPLAY RETURN/EXIT TV TV?/1 AV?/1 SA-CD/CD TUNER F1 9 AMP MENU 0 ENTER 1 Press the input button to select a component. You can also use INPUT SELECTOR on the receiver. The selected input appears on the display. F2 JUMP PICTURE WIDE FAVORITES THEATER TOOLS/ OPTIONS MENU/HOME?/1 GUIDE SOUND FIELD MUTING TV VOL MASTER VOL Input buttons MUTING MASTER VOL +/ Selected input [Display] DMPORT [DMPORT] VIDEO1 or VIDEO2 [VIDEO 1 or VIDEO 2] BD [BD] DVD [DVD] SAT [SAT] TV [TV] SA-CD/CD [SA-CD/CD] TUNER [FM or AM band] Components that can be played back DIGITAL MEDIA PORT adapter connected to the DMPORT jack VCR, etc., connected to the VIDEO 1 or VIDEO 2 jack Blu-ray disc player, etc., connected to the BD jack DVD player, DVD recorder, etc., connected to the DVD jack Satellite tuner, set-top box, etc., connected to the SAT jack TV, etc., connected to the TV jack Super Audio CD/CD player, etc., connected to the SA-CD/CD jack Built-in radio tuner 2 Turn on the component and start playback. 3 Press MASTER VOL +/ to adjust the volume. You can also use MASTER VOLUME on the receiver. Playback To activate the muting function Press MUTING. The muting function will be canceled when you do the following. Press MUTING again. Increase the volume. Turn off the receiver. To avoid damaging your speakers Before you turn off the receiver, be sure to turn down the volume level. 27 US

28 Enjoying sound/images from the components connected to the receiver Input buttons TV Enjoying TV TV INPUT DMPORT SYSTEM STANDBY VIDEO1 VIDEO2 BD DVD SAT BD/DVD TOP MENU MENU CLEAR DISPLAY AMP MENU 0 ENTER RETURN/EXIT TV CH MENU/HOME TV CH + PRESET REPLAY ADVANCE PRESET +. < > TUNING TUNING + TV 1 Turn on the TV and choose a program. For details, refer to the operating instructions of the TV. 2 Turn the receiver on. 3 Press TV. 4 Adjust the volume of the receiver. TV SA-CD/CD TUNER F1 9?/1 F2 JUMP PICTURE WIDE FAVORITES THEATER m TV?/1 AV?/1 TOOLS/ OPTIONS H X < GUIDE SOUND FIELD MUTING TV VOL MASTER VOL M x?/1 SOUND FIELD MASTER VOL +/ Tips When you connect a Sony TV, the audio input of the TV is switched and the image from the TV tuner is displayed on the TV screen automatically by pressing the TV button. To change this setting, see Changing the input button assignments (page 48). The sound may be output from the TV s speaker. In this case, turn the volume of the TV s speaker down to the minimum. Enjoying a satellite tuner 1 Turn on the TV. For details, refer to the operating instructions of the TV. 2 Turn the satellite tuner and the receiver on. 3 Press SAT. You can also use INPUT SELECTOR on the receiver to select SAT. 4 Change the TV input. For details, refer to the operating instructions of the TV. 5 Adjust the volume of the receiver. Tip The sound may be output from the TV s speaker. In this case, turn the volume of the TV s speaker down to the minimum. 28 US

29 Enjoying Blu-ray Disc or DVD 1 Turn on the TV. 2 Turn the Blu-ray Disc or DVD player (recorder) and the receiver on. 3 Press DVD or BD. You can also use INPUT SELECTOR on the receiver to select DVD or BD. Be sure to change the factory setting of the DVD input button on the remote so that you can use the button to control your DVD player. For details, see Changing the input button assignments (page 48). 4 Change the TV input. For details, refer to the operating instructions of the TV. 5 Play back the disc. 6 Adjust the volume. Tip Even if you playback Dolby True HD, Dolby Digital Plus or DTS-HD with a connected component compatible with these sound formats, the receiver accepts as Dolby Digital or DTS. When you connect the component to the receiver using an HDMI cable to playback these high-quality sound formats, set the connected component to output the sound in multi channel PCM, if possible. Enjoying a VCR 1 Turn on the TV. 2 Turn the VCR player and the receiver on. 3 Press VIDEO1 or VIDEO2. You can also use INPUT SELECTOR on the receiver to select VIDEO 1 or VIDEO 2. 4 Change the TV input. For details, refer to the operating instructions of the TV. 5 Play back the tape on the VCR. Enjoying a Super Audio CD/CD 1 Turn on the Super Audio CD player/cd player, then place the disc on the tray. 2 Turn on the receiver. 3 Press SA-CD/CD. You can also use INPUT SELECTOR on the receiver to select SA-CD/CD. 4 Adjust the volume. Playback 29 US

30 Amplifier Operations Navigating through menus To return to the previous display Press B. To exit the menu Press AMP MENU. By using the amplifier menus, you can make various adjustments to customize the receiver CLEAR DISPLAY 9 SOUND FIELD AMP MENU 0 ENTER TOOLS/ OPTIONS GUIDE MUTING AMP MENU, V,v,B,b TV VOL MASTER VOL RETURN/EXIT TV CH MENU/HOME TV CH + PRESET REPLAY ADVANCE PRESET +. < > TUNING TUNING + m H M < 1 Press AMP MENU. SET HDMI appears on the display. 2 Press V/v repeatedly to select the menu you want. 3 Press or b to enter the menu. 4 Press V/v repeatedly to select the parameter you want to adjust. 5 Press or b to enter the parameter. 6 Press V/v repeatedly to select the setting you want. 7 Press or b to enter the setting. 30 US

31 Overview of the menus The following options are available in each menu. For details on navigating through menus, see page 30. Menu [Display] HDMI settings [SET HDMI] (page 33) Auto Calibration settings [A.CAL] (page 33) Speaker settings [SP SETUP] (page 34) Parameters [Display] Control for HDMI a)b) [CONTROL FOR HDMI] Volume limits a) [VOL LIM] Power save a) [P.SAVE] Auto calibration start a) [START] Clear Auto Calibration result a)d) [A.CAL CLR] Center speaker a) [CNT SP] Surround speakers a) [SUR SP] Front left speaker distance a)e) [FL DIST] Center speaker distance a)e) [CNT DIST] Front right speaker distance a)e) [FR DIST] Surround right speaker distance a)e) [SR DIST] Surround left speaker distance a)e) [SL DIST] Subwoofer distance a)e) [SW DIST] Settings Initial setting CTRL ON, CTRL OFF CTRL OFF c) MAX, 39 1, MIN SAVE ON, SAVE OFF For details, see Performing Auto Calibration (page 23). YES, NO CNT Y, CNT N SUR Y, SUR N FL 0.00 m to FL 7.00 m (FL 0.00 ft. to FL ft.) (0.10 m (0.25 ft.) step) CNT 0.00 m to CNT 7.00 m (CNT 0.00 ft. to CNT ft.) (0.10 m (0.25 ft.) step) FR 0.00 m to FR 7.00 m (FR 0.00 ft. to FR ft.) (0.10 m (0.25 ft.) step) SR 0.00 m to SR 7.00 m (SR 0.00 ft. to SR ft.) (0.10 m (0.25 ft.) step) SL 0.00 m to SL 7.00 m (SL 0.00 ft. to SL ft.) (0.10 m (0.25 ft.) step) (SW 0.00 m to SW 7.00 m) (SW 0.00 ft. to SW ft.) (0.10 m (0.25 ft.) step) MAX SAVE ON NO CNT Y SUR Y FL 3.00 m (FL ft.) CNT 3.00 m (CNT ft.) FR 3.00 m (FR ft.) SR 3.00 m (SR ft.) SL 3.00 m (SL ft.) SW 3.00 m (SW ft.) Amplifier Operations continued 31 US