Installation & Operation Manual. BEC PM1 Controller Time/Flow/Volume Controller. Water Control Solutions

Size: px
Start display at page:

Download "Installation & Operation Manual. BEC PM1 Controller Time/Flow/Volume Controller. Water Control Solutions"

Transcription

1 Installation & Operation Manual BEC PM1 Controller Time/Flow/Volume Controller Water Control Solutions

2 Table of Contents Introduction 4 Chapter 1 Technical Data and I/O Connections 6 DC Solenoid 6 Power Supply 6 Hydrometer or Water Meter 6 Flow Switch / Rain Sensor 7 Wiring Table 7 Switching the Controller's Operation Modes 8 Chapter 2 Pressure Management according to Flow-rate Application 9 Background 9 The Control Panel Display Icons 10 Programming Steps 11 Basic Settings 11 AUTO Operation 13 Chapter 3 Pressure Management according to Time Intervals Application 14 The Control Panel 14 Display Icons 15 Programming Steps 16 2

3 Basic Settings 16 Application Description 18 Programming the Pressure Management by Time Intervals Application 18 Chapter 4 On/Off Control Application 20 Dead-end Pipes Purging Application Settings 20 Chapter 5 On/Off Irrigation Application 26 Display Icons 26 Programming Steps 27 Basic Settings 27 Irrigation Program Settings 29 Volumetric Irrigation Program Parameters 30 Irrigation Program Common Parameters 31 Operational Screens 33 Alerts 34 Fault Messages Table 35 Buttons 35 General Information for All Applications 36 Monitoring 36 Manual Operations 37 3

4 Introduction This document provides installation and operation instructions for the BEC PM1 controller as it is used with BERMAD s control valves in Waterworks and Irrigation Applications. Very Important: Chapter #1 of this document provides general installation and operation instructions which are common to all the applications types while the rest of the chapters are organized by application type. Therefore before installing and operating this controller please read carefully chapter #1 and then jump to the chapter related to your specific application: Pressure Management Applications: Optimizing water supply and reducing non revenue water by using the BEC PM1 controller is done by connecting it to BERMAD s two step pressure reducing valve installed at the entry point of a district metering area. Chapter #2 Pressure management according to flow rate: For switching between the two pre-set pressure regimes of the PRV according to high or low flow demand at the controlled district please refer to chapter #2 of this document. 4 Chapter #3 Pressure management according to time intervals: For switching between the two pre-set pressure regimes of the PRV according to time settings please refer to chapter #3 of this

5 document. Chapter #4 On/Off Control: The BEC PM1 enables a volumetric control of BERMAD s On/Off control valves that are used for purging pipe s dead ends, refreshing reservoirs and other such On/Off applications. Please refer to chapter #4 if your specific application in of an On/Off type. Chapter #5 Irrigation Control: The BEC PM1 controller can be used as a single station irrigation controller for agriculture or gardening. Please refer to chapter #5 if your specific application is of an irrigation type. 5

6 Chapter #1 Technical Data and I/O Connections 6 The following I/Os are used for BERMAD s waterworks and Irrigation Applications: DC Solenoid: Connect the solenoid s wires to the cable coming out of the controller s first station port. Connect the solenoid s RED wire to the controller s RED wire and the BLACK wire to the controller s BLACK wire. Power supply: Open the battery s compartment lid and connect a good-quality 9 Volt alkaline battery, then firmly close the lid. When the battery is first connected, the controller performs a selftest, closes the DC solenoid and displays the first settings screen. Under normal use, the battery should last for at least one season. Hydrometer or Water Meter: BERMAD s 900 series Hydrometer, or a water meter with dry contact pulse output, is used in applications such as the following: n Pressure management with flow rate reference applications where switching to the high pressure setting is done in case of a high demand for water. n Pipes dead-end purging applications where the purged-out water is measured by volume and not by time. n In cases of fire protection or volumetric irrigation applications. Connect the two water meter pulse wires to the two controller s RED wires. Please note that there is no polarity significance in this connection.

7 Flow Switch/Rain Sensor: Flow switch can be used with the time controlled pressure management application for switching to the high pressure setting in case of a high demand for water, i.e. in case of fire. Wiring Table: The controller is supplied with the following wires connected to its terminal strip: Wire Color RED BLACK RED BLACK RED RED YELLOW YELLOW Task Remarks DC type solenoid - 9V-12V DC Latch - for pressure management according to flow-rate This wire is joint together with To be connected to the the solenoid's RED wire in the solenoid's RED wire controller's black cable This wire is joint together with To be connected to the the solenoid's BLACK wire in solenoid's BLACK wire the controller's black cable DC type solenoid - 9V-12V DC Latch - for pressure management according to time interval To be connected to the solenoid s BLACK wire To be connected to the solenoid's red wire This wire is joint together with the solenoid's BLACK wire in the controller's black cable This wire is joint together with the solenoid's RED wire in the controller's black cable Water meter Connect one of the watermeter's pulse wires to one of the controller's RED wires Connect the other watermeter's pulse wires to one of the controller's RED wires Flow switch (or rain sensor for irrigation applications) Cut the YELLOW loop and connect one of the flow switch wires to one of the controller's yellow wires. Connect the other flow switch wire to one of the controller's YELLOW wires. There is no polarity significance in this connection There is no polarity significance in this connection There is no polarity significance in this connection There is no polarity significance in this connection 7

8 Switching the Controller's Operation Modes The BEC PM1 controller has two distinctive operation modes: Irr mode - this is the default operation mode of the controller which is used for Irrigation, Time Intervals Pressure Management and On/ off applications. Pr mode - this mode is used for the Pressure Management according to Flow-rate application only. Switching between these two operation modes is done by simultaneously pressing the and keyboard buttons. For example: Changing from Irr to Pr mode: Press the and buttons simultaneously for 5 second, the system displays the mode name and starts switching to the Pr mode. Continue pressing the buttons for additional 3 seconds until the software version appears on screen (in a form of a number) then release the buttons. The controller is now on its Pr mode. Please note that changing the controller s mode requires about 10 seconds of continuous buttons pressing time in total. Changing from Pr to Irr mode: Keep pressing the and buttons for another 3 second, the system displays the new mode name and switches back to the Irr mode. Important! Before operation the controller for the first time make sure that it is set to the correct operation mode for your specific application. 8

9 Chapter #2 Pressure Management according to Flow-rate Application Background This application enables the user to set a flow rate SET POINT in number of pulses per hour. The application automatically changes the control state of the Two Step Pressure Reducing Valve which is controlled by the BEC PM1 controller according to the actual real-time flow-rate reading. When the actual flow rate reading crosses the SET POINT, the controller starts counting a stabilization time delay parameter for ensuring that the flow-rate crossing of the set-point is not a temporary pressure fluctuation. If by the end of the delay counting the flow-rate reading remains beyond the set point the solenoid state changes. There are two delay time parameters: One for LOW to HIGH flow crossing of the set-point and the other for HIGH to LOW flow crossing. This application has four screens: The first three screens are used for setting the SET POINT flow reference [SP:PH] and the two values of the delay timers [SP:tH] & [SP:tL]. The fourth screen is the automatic operation screen ( AUTO ) that is used for monitoring the application operation. 9

10 The Control Panel Button Name NEXT SHIFT ON + Usage Next Step button - used to advance to the next screen Shift button - Not in use in this application Used for increasing a numeric value & OFF - Display Icons The following icons may appear on the screen during programming or operation modes: Icon Symbol Used for switching between the Pr and Irr operation modes Switch between Pressure Management by Flow ( Pr ) and Pressure Management by Time ( Irr ) Applications Pressure Management by Flow Description PM Pressure Management indication Setting Mode The last measured flow rate is higher than the set point threshold [Pulses/Hour] The last measured flow rate is lower than the set point threshold [Pulses/Hour] 10 Automatic operation screen. Used for monitoring the system operation

11 Programming Steps Basic Settings: Setting Flow Reference Set-point Upon entering to this screen the display shows the [SP:PH] (Set Point : Pulses per Hour) title. Use the or the buttons to set the flow-rate value by number of pulses per hour. This is the flow-rate that distinguishes between high and low pressure conditions. Please note: The flow reference entry ranges between 0 and 9999 pulses/hour. The factory default value is 50 pulses per hour. Press the button to move to the next screen. Fig.1 - Flow set-point Setting the Low to High flow stabilization delay timer Upon entering to this screen the display shows the [SP:tH] (Set Point : High flow timer) title. Use the or the buttons to set the required delay time parameter which is used for verifying that the change from LOW flow to HIGH flow is stable. Please note: The timer values range between 0 and 60 minutes in 1 minute steps. The factory default value is 1 minute. Press the button to move to the next screen. Fig.2 - High flow timer 11

12 Setting the High to Low flow stabilization delay timer Upon entering to this screen the display shows the [SP:tL] (Set Point : Low flow timer) title. Use the or the buttons to set the required delay time parameter which is used for verifying that the change from High flow to Low flow is stable. Please note: The timer values range between 0 and 180 minutes in 1 minute steps. The factory default value is 20 minutes. Press the button to move to the next screen. Fig.3 - Low flow timer 12

13 Auto operation Monitoring When no button is pressed in the controller s keyboard for 3 minutes, the controller moves to the main monitoring screen indicated by the word AUTO in the middle of the screen. The AUTO screen displays the following data items: The AUTO icon indicates that the automatic Pressure Management operation is active. The Display shows the current reading of the system s flow-rate. High flow reading The Up arrow indicates that the current flow-rate is higher than the SET POINT flow parameter. High flow reading The DOWN arrow indicates that the current flow-rate is lower than the SET POINT flow parameter. Low flow measurment When the solenoid status is ON the 1 Icon appears on the screen. When the solenoid status is OFF the 1 Icon disappears. 13

14 Chapter #3 Pressure Management according to Time Intervals Application The Control Panel The BEC PM1 Human-Machine Interface consists of a graphical display screen and a four keys keyboard: NEXT STEP button - Used to advance to the next screen or programming step SHIFT button - Used to sequentially change the focus between the items of the current screen PLUSE / ON button - Used to increase numeric data, set on operation days and start manual operation MINUS / OFF button - Used to decrease numeric data, set off operation days and stop manual operation 14

15 Display Icons The following icons may appear on the display screen during programming or operation modes: Setting Mode High Flow [seconds] Set Time / Time Mode Operation Days Volumetric Mode Manual Operation Operation Time Uncontrolled Water Meter [minutes] Automatic Operation 1 Station Number Seasonal Adjustment Flow OFF Stopped by Flow Switch AL:bt Low Battery 15

16 16 Programming Steps This chapter describes the required programming steps of the controller and it is divided into three sections: Basic Settings, Pressure management settings, and end of line flushing settings. Basic Settings: First Basic Settings Screen The basic controller setting should be done once the controller is wired to the system and the power is connected, or after a total reset operation is performed. The first setting screen appears displaying 3 optional settings: 1. Solenoid Type: Upon initial start-up the connected solenoid type is checked by the controller; it must be a DC latch solenoid. 2. Clock Mode: Press the bbutton and set the system clock to 12 or 24 hour clock. Factory default - 24h. 3. Time / Volume Operation: Press the button and select the required operation mode. Select TIME for BERMAD s pressure management by time application. Note the icons change according to your selection: the icon should be selected for time operation. Factory default - Time. Press the button to move to the next basic settings screen. Second Basic Settings Screen In the second setting screen the operator can set the Flow Switch usage mode. Please note that a flow switch can be used only for BERMAD s pressure management by time intervals application.

17 Flow switch mode: Press the button to enable or disable the flow switch operation. When a flow switch is enabled the icon appears on screen. Factory default - flow switch enabled. Press the button to move to the next basic settings screen Third Basic Settings Screen The third setting screen is used for setting the system time and day of the week. System Time: Use the and the buttons to set the system time. Hold the button pressed to quickly advance the digits. Press both buttons simultaneously to reset the time and day to the factory default setting. Day of the week: Use the button to scroll through the days of the week and set the current day. Press the button to exit the basic settings screens and move to the operation programming screens. 17

18 18 Pressure Management Application Settings BERMAD s pressure management by time application is based on BERMAD control valve equipped with two pressure reducing pilots: one for high pressure setting and the other for low pressure setting. Normally the high pressure pilot controls the valve, while the low pressure pilot is on standby mode. A BEC PM1 controller with a DC solenoid can switch the high pressure pilot with the low pressure pilot according to a pre-defined time based operation regime. Such arrangement can switch the system to low pressure settings during night, while maintaining high pressure during day time. The system is also equipped with a high flow switch that can stop the low pressure regime when higher demand for water is detected, such as in case of fire. The following chapter describes the programming steps required for setting-up this application: Programming the Pressure Management by Time Intervals Application The BEC PM1 operation programs consist of three parameters per each valve program: Operation Time, Operation Days, and Start Time. For controlling BERMAD s Pressure Management by Time Interval Application the controller is supplied with a single solenoid (valve), operated by time with up to three start times a day, and with a flow switch. In municipal water systems the demand for water in residential neighborhoods is high during the mornings and evenings and low during the night and mid-day hours; therefore, the control valve is set for the high pressure during high demand hours. Operating the valve with the BEC PM1 controller reduces the otherwise too high pressure settings during the low demand hours.

19 For example, in typical municipal pressure regime, the day low pressure hours are between 10:00 AM and 06:00 PM and the night low pressure hours are between 10:00 PM and 06:00 AM, during the high demand hours the valve maintains the high pressure setting. Therefore, the three required program parameters of the controller are: Operation Time - 8 hours, Operation Days - 7 days and two Start Times one at 10:00 AM and the other at 10:00 PM. 1. Operation Time: Use the button to move to the Operation Time programming screen, this is the screen with the blinking icon, the blinking triangle with the digit 1 in it, and the icon. Use the buttons to set the required operation time (8:00 hours in our example). Press the button to move to the next programming screen which is the Operation Days screen. 2. Operation Days: Use the button to set a particular day as an operation day, or use the button to skip the day, the cursor will advance to the next day. In our example set all 7 week days for operation. Press the button to move to the next programming screen which is the Start Times screen. 3. Start Times: Use the and the buttons to set the first required Start Timed (10:00 AM in our example). Press the button to move to the second Start Time and set it as required (10:00 PM in our example). The controller is now set for automatically operating the Pressure Management by Time Intervals Application. 19

20 Chapter #4 On/Off Control Application The BEC PM1 enables a volumetric or time based control of BERMAD's On/Off control valves that are used for purging pipe's dead ends, refreshing reservoirs and other such On/Off applications. This chapter describes the Dead-end Pipes Purging Application Settings. Dead-end Pipes Purging Application Settings Due to operational conditions, in some municipal and industrial water systems, there is a need for periodic purging of the systems dead-ends of pipes for refreshing the water supply. BERMAD s control valves equipped with BEC PM1 controllers can be installed in these systems. BERMAD s Dead-end Pipes Purging Application accounts for the purging out of the system. This task is automatically performed based on three major parameters: 1. Purging interval - set at specific days of the week or as day intervals 2. Amount of purged water - set by operation time or by volume 3. Start time - set for the operation day (with up to three start times per such day) The following examples depict three typical scenarios: 20

21 A. Purging interval by Days of the Week and purging amount by operation time: In this example the pipe needs to be purged for 5 minutes every Monday and Friday at 08:00 AM. Therefore, the three required program parameters of the controller are: Operation Time - 5 Minutes, Operation Days - Monday and Friday, and Start Time at 08:00 AM. 1. Operation Time: Use the button to move to the Operation Time programming screen - this is the screen with the blinking triangle with the digit 1 in it and the icon. icon, the blinking Use the and the buttons to set the required operation time (00:05 minutes in our example). Press the button to move to the next programming screen which is the Operation Days screen. 2. Operation Days: Use the button to set a particular day as an operation day, the cursor will advance to the next day. In our example set Monday and Friday for operation. Press the button to move to the next programming screen which is the Start Times screen. 3. Start Time: Use the and the buttons to set the required Start Time (08:00 in our example). The controller is now set for automatically operating this Dead end Pipes Purging Application. 21

22 B. Purging interval by Days Interval and purging amount by operation time: In this example the pipe needs to be purged for 5 minutes every 10 days at 08:00 AM. Therefore the three required program parameters of the controller are: Operation Time - 5 Minutes, Operation Interval - 10 days and Start Time at 08:00 AM. 1. Operation Time: Use the button to move to the Operation Time programming screen - this is the screen with the blinking icon, the blinking triangle with the digit 1 in it and the icon. Use the and the buttons to set the required operation time (00:05 minutes in our example). Press the button to move to the next programming screen which is the Operation Days screen. 2. Operation Interval: On the days of the week screen press the button 7 times for skipping the operation by days of the week and advancing the cursor to the Days Cycle line. Two numbers appear on this line: the right number presents the program s Days Interval and the left number display the number of days left till the next operation day. Note that during the first setup of this program the number of day till next operation number is zero. Use the and the buttons to set the required Days Interval (10 days in our example). Note that the maximal interval is 30 days. Press the button to move to the next programming screen which is the Start Times screen. 22

23 3. Start Time: Use the and the buttons to set the required Start Time (08:00 in our example). The controller is now set for automatically operating this Dead-end Pipes Purging Application. C. Purging interval by days of the week and purging amount by Water Volume: In this example the pipe needs to be purged for 50 water meter pulses every Monday and Friday at 08:00 AM. Therefore, the three required program parameters of the controller are: Operation Volume - 50 pulses, Operation Days - Monday and Friday, and Start Time at 08:00 AM. In order to operate this application the BEC-PM1 controller should be connected to BERMAD s 900 Series Hydrometer or to another BERMAD control valve and to a water meter. The BEC PM1 controller should be also set to volumetric operation, which can be done only at the initial setup process of the controller (when power is connected or when the controller s reset operation is performed). 1. Operation Volume: Make sure that the controller is configured for Volume operation as described in the BASIC SETTINGS chapter early in this document. Once a Volumetric operation is set on the first setup screen, press the icon to move to the next water meter setting screen. This screen allows the user to set the following water meter parameters: High Flow Rate (H.F.R.) - indicated by the on-screen icon. This parameter defines the minimal allowed time between two water meter pulses. When pulses are received in shorter interval than this parameter a High Flow indication is presented by the controller 23

24 and the operation stops. (See the fault messages paragraph in the monitoring chapter of this document.) The factory default is 60 seconds; use the and the buttons to set the required H.F.R. parameter. Press the button to move to the next water meter setup parameter. Timer Override (T.O.R.) - indicated by the on-screen icon. This parameter defines the maximal allowed time between two water meter pulses. When pulses are received in longer interval than this parameter a water meter malfunction indication is presented by the controller and the operation stops. (See the fault messages paragraph in the monitoring chapter of this document.) The factory default is 10 minutes; use the and the buttons to set the required T.O.R. parameter. Press the parameter. button to move to the next water meter setup Fill-Up Time (F.U.T.) - indicated by the on-screen icon. This parameter defines the time it takes to fill-up the system pipes at the beginning of the valve operation. During this time the system does not enter to High Flow fault. In purging systems where the purged water is released by open-end pipe to the atmospheric pressure, the flow rate can be high. Make sure that the F.U.T. and the H.F.R. parameters are correctly set for your system requirements. The F.U.T. factory default value is 6 minutes and it can be changed by the and buttons. Press the button to move to the next programming screen. Move to the Operation length programming screen, this is the screen 24 with the blinking icon, the blinking triangle with the digit 1 in it, and the XX icon. Use the XX and the icon. Use the buttons to

25 set the required operation volume (050 pulses in our example). Press the button to move to the next programming screen which is the Operation Days screen. 2. Operation Days: Use the button to set a particular day as an operation day, the cursor advances to the next day. In our example set Monday and Friday for operation. Press the button to move to the next programming screen which is the Start Times screen. 3. Start Time: Use the and the buttons to set the required Start Time (08:00 in our example). The controller is now set for automatically operating this Dead-end Pipes Purging Application. 25

26 Chapter #5 Irrigation Application Display icons Setting Mode Automatic Operation Set Time / Time Mode Watering Volume / Volumetric Mode Seasonal Adjustment Rain OFF - No Watering [static] Watering Time Stopped by Rain Sensor Operation Days High Flow [seconds] Manual Operation Uncontrolled Water Meter Operation [minutes] 26 System Fill up time 1 Station Number Icon AL:bt Low Battery

27 Programming Steps This chapter describes the required programming steps of the controller and it is divided into two: Basic Settings and Irrigation management settings. Basic Settings: First Basic Settings Screen The basic controller setting should be done once the controller is wired to the system and the power is connected, or after a total reset operation is performed. The basic settings consist of the following: Solenoid Type: Upon initial start-up the connected solenoid type is checked by the controller; it must be a DC latch solenoid. 27

28 Factory Default - DC Solenoid Clock Mode: NOTE: This value can be set only after power-up or full unit reset. 88:24 88:12 Factory default - 24h. Press button and set the system clock to 12 or 24 hour clock. Time / Volume Operation: NOTE: This value can be set only after power-up or full unit reset. Press the button and select the required Factory Default: operation mode. Select between TIME and Volume TIME and note the icons change according to your selection. The selected method indication (time/volume) is shown on the controller s operational screens. Press the button to move to the next basic settings screen. Second Basic Settings Screen Rain Sensor Mode: Press the button to enable or disable the rain sensor operation. Press the button to move to the next basic settings screen. Factory Default: Rain Sensor Enabled 28

29 Third Basic Settings Screen Set the current Time and Day of the Week: SU System Time: Factory Default: Use the and the buttons to set the system 06:00 AM time. Hold the button pressed to quickly advance Sunday the digits. Press both buttons simultaneously to reset the time and day to the factory default setting. Press the button to move to the day of the week settings. Day of the Week: Use the button to scroll through the days of the week and set the current day. Press the button to exit the basic settings screens and move to the Irrigation programming screens. Irrigation Program Settings: General Notes Each irrigation program consists of three parameters for each station: 1. Watering by Time / Volume 2. Watering Days 3. Program / Station Start Time Use the button to move through the programming steps, note that the pointing hand icon blinks throughout the programming process. NOTE: Volumetric irrigation requires setting of additional three parameters: H.F.R., T.O.R. and F.U.T. 29

30 Volumetric Irrigation Program parameters Volumetric Mode Only NOTE: Setting OFF one of the flow limit parameters may end with an un-controlled watering in case of burst pipes or wire disconnection. It is NOT recommended to set OFF any of these limit parameters. Setting the High Flow-Rate Limit (H.F.R.) This parameter defines the minimal allowed time between two water meter pulses. When pulses are received in shorter interval than this parameter a High Flow indication is presented by the controller and the irrigation stops. Use the and buttons in order to set the H.F.R. value. Press the. button in order to move to the T.O.R. setting. Setting the Timer Override Limit (T.O.R.) Factory Default: 60 Seconds This parameter defines the maximal allowed time between two water meter pulses. When pulses are received in longer interval than this parameter a water meter malfunction indication is presented by the controller and the irrigation stops. Factory Default: 10 minutes Use the and buttons in order to set the T.O.R. value. Press the. button in order to move to the F.U.T. setting. 30

31 Setting the Fill-Up Time (F.U.T.) DAYS CYCLE This parameter defines the time it takes to fill-up the system pipes at the beginning of the valve operation. During this time the system does not enter to High Flow fault. Use the and buttons in order to set the F.U.T. value. In order to return to the H.F.R. settings press the button. Factory Default: 6 minutes Press the button in order to move to next settings screen. Irrigation Program Common Parameters Used for all Irrigation Modes Watering by Time/Volume NOTE: It is necessary to set the Time/Volume parameter other than OFF in order for the controller to operate automatically. Use the button to increase the watering Time/Volume parameter or use the Time/Volume. Factory Default: OFF (No watering) button to decrease the Press the button to program the watering days. 31

32 Watering Days NOTE: It is necessary to set at least one watering day in order for the controller to operate automatically. First Screen - Days of the Week: Press the button to set a particular day as irrigation day or the to skip that day. The cursor advances to the next day. To set irrigation by days cycle, press the button till the screen shows 0 0. Factory Default: All days are OFF Second Screen - Days Cycle: Press the button to increase the cycle by a single day or press the to decrease the cycle by a day. Note that the cycle interval range is between 1 to 30 days. On the right side of the screen the cycle length is shown and the remaining days till the next irrigation day are shown on the screen s left side. Press the button in order to program the watering start times. Start Time NOTE: It is necessary to set at least one Start Time in order for the controller to operate automatically. Up to 3 start times per irrigation day can be set to each station (MP) or for each program (SP). Press on the button to increase or the button to decrease the Start Time setting. Press the button to move to the operational screens START X Factory Default: All start times are OFF 32

33 Operational Screens Manual Mode Manual Watering Screens NOTE: to switch to the MANUAL screens press and hold the NEXT button for at least 2 seconds at any stage. Common to both screens: Press the or the buttons to switch the valve ON or OFF. A Switched ON Station Icon appears on the screen together with the remaining irrigation countdown. If the station is left ON it will shut off automatically according to its programmed time/volume watering setting. If no time/volume is set for the station it will shut off automatically after two minutes/pulses irrigation. A Switched OFF Station Icon blinks and the current time is displayed. START X Single station Start The controller returns to the AUTO screen after 3 minutes with no activity on the MANUAL screen. Press the button in order to move to the AUTO screen. Auto Mode - Auto screen When no button is pressed in the controller s keyboard for 3 minutes, the controller moves to the main monitoring screen indicated by the word AUTO in the middle of the screen. The AUTO screen displays the following data items: The current time and day The remaining irrigation time or volume The display shows the current reading of the system s flow-rate. NOTE that any active alert message overrides this screen s regular data. To cancel an alert press the and buttons simultaneously. Press both and in order to cancel an alert. In order to stop irrigation (Rain-OFF) or to resume it, press both &. Press the button in order to move to the WATER BUDGET screen. [ ] Automatic Operation 33

34 Water Budget - Seasonal Adjustment Percentage scaling adjustment can be used in order to increase or decrease the Watering Time/Volume for all the irrigation stations. This method is useful when the watering Time/Volume needs to be changed due to seasonal or weather reasons. Watering scaling ranges within 10% - 200% in 10% steps. Press the [ ] Factory Default: 100% button in order to move to the Settings Screens. Alerts Common to all Alerts: n Sticky alert screen During active alert the controller displays the alert type message. As long as the alert is active the message is Sticky on the screen foreground. Blinking icons are shown when trying to leave the screen. In order to move to another screen it is necessary first to cancel the alert. n Canceling alert is done by pressing the and buttons simultaneously. n NOTE: Watering does not take place as long as the alert exists; cancel the alert in order to resume operation. n Simultaneous Alerts - in cases where more than a single alert exists in the system, the controller alternates the alert type messages on screen. 34

35 Fault Messages Table Type Display Operation stopped at: Remarks Low Battery "AL:bt" All Valves (!) "OFF" icon is lit Too High Current Usage "AL:Cr" The faulty valve only 1 The valve's number icon is lit High Flow "AL:HF" The faulty valve only 1 The valve's number icon is lit Timer Override Buttons Buttons Combination "AL:tr" All Valves (!) Function Automatically canceled at midnight Remarks Short press Go to Next Screen Cyclic Activity 2 sec. press Go to MANUAL Screen 10 sec. press Unit RESET & & & Rain-OFF In/Out Set Factory Default Value Cancel an Alert Quick Jump Programmed data will be lost 2 sec. press at AUTO- Run screen In all Setting Screens 2 sec. press during active alert 35

36 General Information for all Irr Applications Monitoring When no button is pressed in the controller s keyboard for 3 minutes, the controller moves to the main monitoring screen indicated by the word AUTO in the middle of the screen. The AUTO screen displays the current status of the controller, which includes the current time and day, as well as the switched ON valve indication and its remaining operation time or volume. During a fault or malfunction mode the relevant fault message overrides the AUTO screen data, see the Fault Messages Table on page. To cancel the fault check the system for the cause of the fault, repair the necessary components and then press the buttons simultaneously for 2 seconds. Please note: and the n When a fault message is displayed on the AUTO screen moving to the other screens is not possible. n In case the controller has more than one fault, this screen alternates the current fault messages every few seconds. 36

37 Manual Operation The operator may manually start / stop the operation of the valve at the manual operation screen. Move to the manual operation screen by pressing the any screen for 2 seconds. The icon appears. button at Use the and the buttons to start or stop the operation of the valve. Please note that when manually started, the valve operates for the duration of its programmed operation time or operation volume. Disclaimer The BEC PM1 is a general purpose controller supplied as an electronic device controlling BERMAD valves. Therefore this document is limited to BERMAD s applications only. 37

38 Copyright BERMAD CS Ltd. All Rights Reserved. The information contained in this document is subject to change without notice. BERMAD shall not be liable for any errors contained herein. PIEWE16-PM1 REV. 1 August 2016

Single Station Waterproof Timer

Single Station Waterproof Timer Single Station Waterproof Timer Installation and Programming Guide Features Up to four irrigation cycles per day Easy installation and programming Battery powered Waterproof and weather resistant 1234

More information

Software Ver

Software Ver - 0 - Software Ver-3.02 CONTENTS 1. INTRODUCTION...- 2-2. MAIN PANEL...- 3-3. SETTING UP TIME AND DAY...- 4-4. CREATING AN IRRIGATION PROGRAM...- 6-4.1 IRRIGATION DAYS AND START TIMES WHEN... - 6-4.2 WATER

More information

G.S.I AC Controller. Installation & User Guide

G.S.I AC Controller. Installation & User Guide G.S.I AC Controller Installation & User Guide 2012 Galcon. All rights reserved. Information in this documentation is subject to change without notice and does not represent a commitment on part of Galcon.

More information

Addendum: Rain Dial Installation and Programming Guide Update

Addendum: Rain Dial Installation and Programming Guide Update Addendum: Rain Dial Installation and Programming Guide Update Your Rain Dial controller has been updated with several new features making it faster to program, easier to maintain, compliant with water

More information

ST8-WiFi Timer. Installation Guide and Operations Manual. English MIN M D YYYY

ST8-WiFi Timer. Installation Guide and Operations Manual. English MIN M D YYYY ST8-WiFi Timer Installation Guide and Operations Manual AM M D YYYY English Contents ST8-WiFi Timer Installation Guide and Operations Manual Introduction Welcome to Rain Bird... 1 Timer Features... 1 Controls

More information

Battery Operated Controllers

Battery Operated Controllers ALL SEASONAL ADJUSTMENT 1 Battery Operated Controllers Owner s Manual and Programming Instructions RUN PRG SENSOR BYPASS SYSTEM OFF CURRENT TIME/DAY ACTIVE MANUAL-ALL STATIONS START TIMES MANUAL-ONE STATION

More information

Junior Max (JR Max ) Controller

Junior Max (JR Max ) Controller Get more done TM Junior Max (JR Max ) Controller stations Operating Instructions Thank you for purchasing this advanced, highly featured Irritrol Junior MAX controller. The Junior MAX is the latest addition

More information

MSC+ Controller. Operation Manual

MSC+ Controller. Operation Manual MSC+ Controller Operation Manual Contents Introduction... 1 Controls and Indicators...1 Programming the Controller... 3 Definitions...3 Programming Checklist...3 Power-Up the Controller...4 Clock Status

More information

SCS318. User Instructions. SCS318 comprising of SCS317 7 Day Wireless Programmable Room Thermostat and SSR303 Receiver

SCS318. User Instructions. SCS318 comprising of SCS317 7 Day Wireless Programmable Room Thermostat and SSR303 Receiver SCS318 User Instructions SCS318 comprising of SCS317 7 Day Wireless Programmable Room Thermostat and SSR303 Receiver Programmable room thermostats are widely recognised as one of the best ways in which

More information

Thank you for purchasing this product. If installing for someone else, please ensure that the instructions are handed to the householder.

Thank you for purchasing this product. If installing for someone else, please ensure that the instructions are handed to the householder. Instruction Manual TPSE201 (181422) - BOSS TM Universal Programmer TPSE101 (569565) - BOSS TM Universal Timeswitch Thank you for purchasing this product. If installing for someone else, please ensure that

More information

Part names (continued) Remote control

Part names (continued) Remote control Introduction Part names (continued) Remote control (1) STANDBY ( 25) (1) (2) ON ( 25) (3) (3) ID - 1 / 2 / 3 / 4 s ( 18) (4) (4) COMPUTER 1 ( 27) (7) (5) COMPUTER 2 * (8) (6) COMPUTER 3 * (10) (13) (7)

More information

Digital Differential Pressure Gauge Switch 0.1 : 0.5 BAR USER GUIDE

Digital Differential Pressure Gauge Switch 0.1 : 0.5 BAR USER GUIDE Digital Differential Pressure Gauge Switch 0.1 : 0.5 BAR USER GUIDE Table of Contents GETTING STARTED DESCRIPTION Display Mechanical Electrical Mounting Programmable Settings Default Factory Settings PARTS

More information

Rain+Birdt. ESP-9V Battery-Operated Controller. User Manual - Table of Contents. Controls and Indicators... 2 Operating Modes... 2

Rain+Birdt. ESP-9V Battery-Operated Controller. User Manual - Table of Contents. Controls and Indicators... 2 Operating Modes... 2 Rain+Birdt ESP-9V Battery-Operated Controer User Manual - Table of Contents Controls and Indicators... 2 Operating Modes... 2 Introduction... 3 Operation and Setup... 3 Contractor Rapid Programming TM...

More information

SSPT724A Timer Quick Start Guide

SSPT724A Timer Quick Start Guide SSPT724A Timer Quick Start Guide Open timer enclosure and remove mounting parts and instructions. When ready to program the timer, plug in timer to 120 Volt Ac power receptacle Press the SET button to

More information

Rain+Birdt. WPX Battery-Operated Controller. User Manual - Table of Contents. Controls and Indicators... 2 Operating Modes... 2

Rain+Birdt. WPX Battery-Operated Controller. User Manual - Table of Contents. Controls and Indicators... 2 Operating Modes... 2 Rain+Birdt User Manual - Table of Contents Controls and Indicators... 2 Operating Modes... 2 Introduction... 2 Operation and Setup... 2 Contractor Rapid Programming TM... 2 Set Date & Time... 2 Set Irrigation

More information

Dial Ezy INSTRUCTION MANUAL N IRRIGATION CONTROLLER 4 or 6 Station Model SUITABLE FOR INDOOR USE ONLY OTHERWISE WARRANTY IS VOID

Dial Ezy INSTRUCTION MANUAL N IRRIGATION CONTROLLER 4 or 6 Station Model SUITABLE FOR INDOOR USE ONLY OTHERWISE WARRANTY IS VOID Dial Ezy IRRIGATION CONTROLLER 4 or 6 Station Model INSTRUCTION MANUAL SUITABLE FOR INDOOR USE ONLY OTHERWISE WARRANTY IS VOID N10372 Table Of Contents Features 1 Glossary 2 Programming Instructions Introduction

More information

SPIRIT. SPIRIT Attendant. Communications System. User s Guide. Lucent Technologies Bell Labs Innovations

SPIRIT. SPIRIT Attendant. Communications System. User s Guide. Lucent Technologies Bell Labs Innovations Lucent Technologies Bell Labs Innovations SPIRIT Communications System SPIRIT Attendant User s Guide Lucent Technologies formerly the communications systems and technology units of AT&T 518-453-710 106449697

More information

ST9100C User Guide. Features

ST9100C User Guide. Features Features Easy to use slider and buttons combined with LoT Technology and an OK button, allows you to confi rm changes and stay in control. PLEASE RESPECT YOUR ENVIRONMENT! Take care to dispose of this

More information

OUTDOOR IRRIGATION CONTROLLER LDC-6 LDC-11. User Manual

OUTDOOR IRRIGATION CONTROLLER LDC-6 LDC-11. User Manual OUTDOOR IRRIGATION CONTROLLER LDC- LDC- User Manual TABLE OF CONTENTS Table of Contents Introduction The Controller Introduction to Programming Watering Schedules Water Budgeting and Seasonal Adjustment

More information

User interface. Abbreviations / Meanings

User interface. Abbreviations / Meanings RG66012649 User interface Contents Page Abbreviations / Meanings Abbreviations / meanings... 2 Button Identification... 3 On-screen Indicators... 4 Quick Start... 5 Setting the time and day... 5 Changing

More information

OPERATION AND MAINTENANCE

OPERATION AND MAINTENANCE BAS MS/TP Enabled OPERATION AND MAINTENANCE An Company Contents Powering Up For The First Time... 3 Setting MSTP Communication Parameters... 4 Changing the MSTP Address... 4 Changing the BACNET ID... 5

More information

Overview: Specifications: Installation Instructions:

Overview: Specifications: Installation Instructions: Overview: The SignalGuys.com Start/Stop Work Timer PT724A is an extremely versatile 24 Hour 365 Day Event Timers designed to support a wide range of applications. Such applications include: Start/Stop

More information

American DJ. Show Designer. Software Revision 2.08

American DJ. Show Designer. Software Revision 2.08 American DJ Show Designer Software Revision 2.08 American DJ 4295 Charter Street Los Angeles, CA 90058 USA E-mail: support@ameriandj.com Web: www.americandj.com OVERVIEW Show Designer is a new lighting

More information

3200NT System 14. Service Manual. IMPORTANT: Fill in Pertinent Information on Page 3 for Future Reference

3200NT System 14. Service Manual. IMPORTANT: Fill in Pertinent Information on Page 3 for Future Reference 3200NT System 14 Service Manual IMPORTANT: Fill in Pertinent Information on Page 3 for Future Reference Table of Contents Job Specification Sheet... 3 Timer Operation... 4 System Operation In Service...

More information

Quick Setup Guide for IntelliAg Model NTA

Quick Setup Guide for IntelliAg Model NTA STEP 3: Auto Configuration (identifies sensors connected to each module) Auto config is performed at the factory, but may need to be done in the field as changes are made to the system or if options are

More information

Sport-TIMER 3000 TM Instruction Manual

Sport-TIMER 3000 TM Instruction Manual Sport-TIMER 3000 TM Instruction Manual Sport-TIMER 3000 TM Index of Uses Page Sport-TIMER 3000 TM RECORD OF PURCHASE The Sport-TIMER 3000 TM is fully warranted to the original purchaser against any defects

More information

Two (2) Channel 365 Day 24 Hr. Timer/Controllers

Two (2) Channel 365 Day 24 Hr. Timer/Controllers Two (2) Channel 365 Day 24 Hr. Timer/Controllers Models include: PT2724 - Timer module PT2724E - Timer module in enclosure Installation Guide Rev. 020317 More than just power. TM Overview: Altronix PT2724/PT2724E

More information

STX Stairs lighting controller.

STX Stairs lighting controller. Stairs lighting controller STX-1795 The STX-1795 controller serves for a dynamic control of the lighting of stairs. The lighting is switched on for consecutive steps, upwards or downwards, depending on

More information

PT Two (2) Channel 365 Day 24 Hr. Timer/Controller

PT Two (2) Channel 365 Day 24 Hr. Timer/Controller PT2724 - Two (2) Channel 365 Day 24 Hr. Timer/Controller Overview: This unit is an extremely versatile two channel 365 Day 24 Hour Timer / Controller designed to support a wide range of applications. Such

More information

USER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.0

USER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.0 by USER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.0 www.aeroforcetech.com Made in the USA! WARNING Vehicle operator should focus primary attention to the road while using the Interceptor. The information

More information

Quick Setup Guide for IntelliAg Model CTA

Quick Setup Guide for IntelliAg Model CTA STEP 3: Auto Configuration (identifies sensors connected to each module) Auto config is performed at the factory, but may need to be done in the field as changes are made to the system or if options are

More information

3214NXT. Service Manual. IMPORTANT: Fill in Pertinent Information on Page 3 for Future Reference

3214NXT. Service Manual. IMPORTANT: Fill in Pertinent Information on Page 3 for Future Reference 3214NXT Service Manual IMPORTANT: Fill in Pertinent Information on Page 3 for Future Reference Table of Contents Job Specification Sheet 3 Timer Operation 4 System Operation in Service 6 Flow in a Four-Unit

More information

IDS. Decoder Controller. Two-wire Decoder Control in an Advanced Industrial Package for the Largest Installations. Programming and Operations Manual

IDS. Decoder Controller. Two-wire Decoder Control in an Advanced Industrial Package for the Largest Installations. Programming and Operations Manual IDS Decoder Controller Two-wire Decoder Control in an Advanced Industrial Package for the Largest Installations Programming and Operations Manual TABLE OF CONTENTS... Introduction...1 How IDS Works...1

More information

Users Manual. Models 96954, 96956, 96874, PN ra. dimensions: flat: w: 14" h: 5" finished: w: 7" d: " h: 5" proof no: 2. date:

Users Manual. Models 96954, 96956, 96874, PN ra. dimensions: flat: w: 14 h: 5 finished: w: 7 d:  h: 5 proof no: 2. date: Users Manual Models 96954, 96956, 96874, 96876 PN 96876-24 ra p 801 295 9820 f 801 951 5815 www.fluid-studio.net 1065 South 500 West Bountiful, Utah 84010 proof no: 2 date: 02.21.11 des: MZ client: Orbit

More information

Instruction Manual. Outdoor Irrigation Controller. STATION MODELS Available in 6, 9 or 12 stations INDOOR & OUTDOOR MODELS

Instruction Manual. Outdoor Irrigation Controller. STATION MODELS Available in 6, 9 or 12 stations INDOOR & OUTDOOR MODELS Outdoor Irrigation Controller STATION MODELS Available in 6, 9 or 12 stations INDOOR & OUTDOOR MODELS Instruction Manual MAC_RPS612_Instruction_Manual.indd 1 CONTENTS Introduction 1 Glossary 2 Key Features

More information

Pro-C. Residential and Light Commercial Irrigation Controllers. PCC Series Controller 6, 9, 12 & 15 Station Indoor/Outdoor Models

Pro-C. Residential and Light Commercial Irrigation Controllers. PCC Series Controller 6, 9, 12 & 15 Station Indoor/Outdoor Models Pro-C Residential and Light Commercial Irrigation Controllers PCC Series Controller 6, 9, 12 & 15 Station Indoor/Outdoor Models Owner s Manual and Installation Instructions Please leave with property owner

More information

Outback STX. User Guide Supplement. Parts List. STX Terminal Overview

Outback STX. User Guide Supplement. Parts List. STX Terminal Overview Outback STX User Guide Supplement This supplement details the following changes from STX v1.0 to STX v1.1: Parts List below STX Terminal Overview below Connection Diagram on page 2 AC110 Power Up and Power

More information

User Manual CC DC 24 V 5A. Universal Control Unit UC-1-E. General Information SET. Universal Control Unit UC-1 Of Central Lubrication PAUSE CONTACT

User Manual CC DC 24 V 5A. Universal Control Unit UC-1-E. General Information SET. Universal Control Unit UC-1 Of Central Lubrication PAUSE CONTACT Universal Control Unit UC-1-E User Manual General Information Universal Control Unit UC-1 Of Central Lubrication CC DC 24 V 5A / M 15 SL /MK 31 M Z 30 General Information Contents Universal Control Unit

More information

ORM0022 EHPC210 Universal Controller Operation Manual Revision 1. EHPC210 Universal Controller. Operation Manual

ORM0022 EHPC210 Universal Controller Operation Manual Revision 1. EHPC210 Universal Controller. Operation Manual ORM0022 EHPC210 Universal Controller Operation Manual Revision 1 EHPC210 Universal Controller Operation Manual Associated Documentation... 4 Electrical Interface... 4 Power Supply... 4 Solenoid Outputs...

More information

TU-8A. 8 Channel Digital Timer Unit. Programming Guide

TU-8A. 8 Channel Digital Timer Unit. Programming Guide TU-8A 8 Channel Digital Timer Unit Programming Guide Introduction Thank you for purchasing the TU-8A 8 Channel Digital Timer Unit. The TU-8A is a weekly event programmable timer providing 8 independent

More information

INSTALLATION and OPERATING INSTRUCTIONS

INSTALLATION and OPERATING INSTRUCTIONS INSTALLATION and OPERATING INSTRUCTIONS Controller Unit ESP-MC Introduction Welcome to Rain Bird! Thank you for purchasing your new, state-of-the-art Rain Bird controller. For more than six decades, Rain

More information

Sample BD Tech Concepts LLC

Sample BD Tech Concepts LLC XYZ Corp. Fry Controller FC-1234 Software Test Procedure Copyright 2014 Brian Dunn BD Tech Concepts LLC Last Modified: 00/00/0000 Version Tested: Date Tested: Technician: Results: 1 FC-1234 SW Test Proc.

More information

Tailgate module BEXPRO PRINS VSI

Tailgate module BEXPRO PRINS VSI new digital technology For any damage that may arise due to our instructions, we can of course, assume no liability. The publication is solely for informational Purposes has been written and contains no

More information

EZ Pro Jr. Installation and Programming Guide For EZ Pro TM Jr. models:

EZ Pro Jr. Installation and Programming Guide For EZ Pro TM Jr. models: EZ Pro Jr. Installation and Programming Guide For EZ Pro TM Jr. models: 8304 8374 8306 8376 8309 8379 8312 8382 THANK YOU for purchasing the EZ Pro Jr. 8300 Series electronic irrigation controller. The

More information

How do I delete a. Remove Here

How do I delete a. Remove Here 2 3 4 5 6 Q. A. Frequently Asked Questions Please read before calling Customer Service. Does your system run repeatedly? Q. How do I delete a start time? Q. Where do I leave the LARGE dial? Do NOT set

More information

Comfort System T-32-P Universal Thermostat. Operation Manual

Comfort System T-32-P Universal Thermostat. Operation Manual TM Comfort System T-32-P Universal Thermostat TM O Operation Manual Your new Comfort System T-32-P Universal Thermostat has been built using the highest quality components and design currently available.

More information

EN Wireless programmable thermostat

EN Wireless programmable thermostat EN Wireless programmable thermostat Contents 1. Installation... 31 2. Description... 32 EN 3. Wireless association... 33 4. Configuration... 34 CF01 - Correcting the temperature measured... 34 CF02 - Temperature

More information

ComfortChoice Touch Thermostat. Designed for ZigBee R Wireless Technology USER GUIDE

ComfortChoice Touch Thermostat. Designed for ZigBee R Wireless Technology USER GUIDE ComfortChoice Touch Thermostat Designed for ZigBee R Wireless Technology USER GUIDE TABLE OF CONTENTS PAGE WELCOME... 8,9 THE TOUCH SCREEN... 10,11 Home - Inactive... 10 Home - Active... 11 PHYSICAL BUTTONS...

More information

User s Guide. GreenKeeper 212 Features: Automatic Sprinkler System Controller

User s Guide. GreenKeeper 212 Features: Automatic Sprinkler System Controller RR User s Guide Automatic Sprinkler System Controller PROGRAMS A B C MANUAL START ON OFF NEXT GreenKeeper 212 Features: Easily Expandable Up To 12 Stations with 2-Station Plug-in Modules Watering Programs

More information

This pocket guide is not intended to replace the instruction manual. Read the instruction manual thoroughly before operating the sampler.

This pocket guide is not intended to replace the instruction manual. Read the instruction manual thoroughly before operating the sampler. This pocket guide is not intended to replace the instruction manual. Read the instruction manual thoroughly before operating the sampler. COPYRIGHT 2001 by Teledyne Isco, 4700 Superior St., Lincoln, Nebraska,

More information

Introduction... 1 Pro-C Components... 2 Pro-C Components Wiring Cabinet... 4 Mounting the Outdoor Controller to Wall... 7

Introduction... 1 Pro-C Components... 2 Pro-C Components Wiring Cabinet... 4 Mounting the Outdoor Controller to Wall... 7 Pro-C Residential and Light Commercial Irrigation Controllers Indoor or Outdoor Versions Owner s Manual and Installation Instructions RAIN SENSOR BYPASS ACTIVE RUN Pro-C SET CURRENT DATE / TIME Please

More information

Understanding and Programming Irrigation Controllers

Understanding and Programming Irrigation Controllers Understanding and Programming Irrigation Controllers E = MC Sun 4 6 7 8 9 Manual On/Off Set Time 0 Mon Set Today Tue Wed Thu Fri Sat E=MC Off % PM Enter Water Times Cycle Start On Clear Prepared by: Jeff

More information

NOTICE: This.pdf file should not. regarding the file (e.g., color, text

NOTICE: This.pdf file should not. regarding the file (e.g., color, text NOTICE: This.pdf file should not be used as the source to create final, printed pieces of the file it represents. Rather, it is a low resolution visual reference only containing relevant information regarding

More information

User Guide AC/DC 2 AC/DC 4 AC/DC 6 AC/DC 9 DC IP68 AC IP65

User Guide AC/DC 2 AC/DC 4 AC/DC 6 AC/DC 9 DC IP68 AC IP65 User Guide AC/DC 2 AC/DC 4 AC/DC 6 AC/DC 9 DC IP68 AC IP65 2 What is in this package? 1 1 2 2 3 What else do I need? 9V 1-9 Moiture sensor (Opional) DC IP68 AC IP65 User Guide F e a t u r e s o f t h e

More information

Table of contents 1. INTRODUCTION GENERAL CONTENTS OF PACKAGE GENERAL USE OF THE EQUFLOW 6100 D/A CONVERTER STORAGE..

Table of contents 1. INTRODUCTION GENERAL CONTENTS OF PACKAGE GENERAL USE OF THE EQUFLOW 6100 D/A CONVERTER STORAGE.. Installation instructions and user s guide Equflow 6100 D/A Converter Please read this manual carefully before installation and use of the converter. 6100 D/A Converter Type: 6100DACONDC03 Despite effort

More information

USER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.1

USER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.1 by USER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.1 www.aeroforcetech.com Made in the USA! WARNING Vehicle operator should focus primary attention to the road while using the Interceptor. The information

More information

ESP-LX Modular Controller Programming & Operation Guide

ESP-LX Modular Controller Programming & Operation Guide ESP-LX Modular Controller Programming & Operation Guide SAFETY INFORMATION WARNING: A CIRCUIT BREAKER OR CUTOFF SWITCH IS TO BE PROVIDED IN THE FIXED WIRING TO ISOLATE THE CONTROLLER. MEMORY IS RETAINED

More information

THE ASTRO LINE SERIES GEMINI 5200 INSTRUCTION MANUAL

THE ASTRO LINE SERIES GEMINI 5200 INSTRUCTION MANUAL THE ASTRO LINE SERIES GEMINI 5200 INSTRUCTION MANUAL INTRODUCTION The Gemini 5200 is another unit in a multi-purpose series of industrial control products that are field-programmable to solve multiple

More information

VF-STB IP Appliance User Guide

VF-STB IP Appliance User Guide VF-STB IP Appliance User Guide Copyright 2007 Video Furnace, Inc. All Rights Reserved. Copyright 2002-2007 Video Furnace, Inc. All Rights Reserved This document refers to the current published version

More information

HOME GUARD USER MANUAL

HOME GUARD USER MANUAL HOME GUARD USER MANUAL CONTENTS 1. SAFETY PRECAUTIONS...2 2. INTRODUCTION...3 3. FEATURES...4 4. ACCESSORIES...5 5. INSTALLATION...6 6. NAME and FUNCTION of EACH PART...7 6.1 Front Pannel...7 6.2 Monitoring

More information

Sentinel I24 Digital Input and Output Configuration

Sentinel I24 Digital Input and Output Configuration Application Bulletin: #155 Date: October 19, 2007 Sentinel I24 Digital Input and Output Configuration The Sentinel I24 can communicate with external hardware using digital inputs and outputs. There are

More information

SINGLE ZONE CLIMATE ZONING SYSTEM. Technical Manual. Polyaire Pty Ltd

SINGLE ZONE CLIMATE ZONING SYSTEM. Technical Manual. Polyaire Pty Ltd SINGLE ZONE CLIMATE ZONING SYSTEM Technical Manual Polyaire Pty Ltd 11-13 White Road GEPPS CROSS South Australia, 5094 Tel: (08) 8349 8466 Fax: (08) 8349 8446 www.polyaire.com.au CONTENTS Features 1 Application

More information

IS SERIES Commercial & Security IP Video Intercom system OPERATION MANUAL

IS SERIES Commercial & Security IP Video Intercom system OPERATION MANUAL 54426 A P06YZ IS SERIES Commercial & Security IP Video Intercom system IS-SOFT PC Master Station OPERATION MANUAL GETTING STARTED USING THE PC MASTER STATION APPENDIX Thank you for selecting Aiphone for

More information

Transmitter Interface Program

Transmitter Interface Program Transmitter Interface Program Operational Manual Version 3.0.4 1 Overview The transmitter interface software allows you to adjust configuration settings of your Max solid state transmitters. The following

More information

Rain+Birdt. Landscape Irrigation & Maintenance Remote System. Quick Start Guide 4.00 F G H K 9X. c n. System Components

Rain+Birdt. Landscape Irrigation & Maintenance Remote System. Quick Start Guide 4.00 F G H K 9X. c n. System Components Rain+Birdt Landscape Irrigation & Maintenance Remote System Quick Start Guide 4.00 D System Components A Transmitter (TX) B Receiver (RX) C Quick Connect (QC) 6-Pin Quick Connect (QC) for use with ESP-Modular

More information

ET-8 Series Manual Wall Mount: 8, 16, 24, 32 Stations Pedestal Ultimo: 8, 16, 24, 32, 40, 48 Stations

ET-8 Series Manual Wall Mount: 8, 16, 24, 32 Stations Pedestal Ultimo: 8, 16, 24, 32, 40, 48 Stations ET-8 Series Manual Wall Mount: 8, 16, 24, 32 Stations Pedestal Ultimo: 8, 16, 24, 32, 40, 48 Stations Table of Contents 1 ET-8 SERIES QUICK SETUP GUIDE... 3 2 INSTALLATION... 4 2.1 Wall Mount Mounting

More information

The smart valve with 3 Independent programs + 2 extra modes

The smart valve with 3 Independent programs + 2 extra modes All right reserved to netafim / Hendelmade 0901 The smart valve with 3 Independent programs + 2 etra modes o opcion rio pro READ & KEEP E AQUA PRO Irrigation Controller Easy to use battery operated irrigation

More information

1 Overview. 2 Specifications. 3 Installation Instructions. HPT724 Programmable LCD Timer PN 52765:A 1/25/06 ECN Product Installation Document

1 Overview. 2 Specifications. 3 Installation Instructions. HPT724 Programmable LCD Timer PN 52765:A 1/25/06 ECN Product Installation Document Honeywell 12 Clintonville Road Northford, CT 06472 http://www.honeywellpower.com HPT724 Programmable LCD Timer PN 52765:A 1/25/06 ECN 05-637 1 Overview Product Installation Document The Honeywell HPT724

More information

imso-104 Manual Revised August 5, 2011

imso-104 Manual Revised August 5, 2011 imso-104 Manual Revised August 5, 2011 Section 1 Getting Started SAFETY 1.10 Quickstart Guide 1.20 SAFETY 1.30 Compatibility 1.31 Hardware 1.32 Software Section 2 How it works 2.10 Menus 2.20 Analog Channel

More information

Goodmans Helpline Phone Number

Goodmans Helpline Phone Number Goodmans Helpline Phone Number 0870 873 0080 contents Introduction 4 Connecting up 5 Overview diagrams 6 Getting started 8 Using the main menu 10 Troubleshooting 15 Technical Specifications 16 3 introduction

More information

HDMI Expander Family EP-HC0408 EP-HC046

HDMI Expander Family EP-HC0408 EP-HC046 HDMI Expander Family EP-HC0408 EP-HC046 EP-HC0408/EP-HC0416 User Manual Version 1.0 Last Updated: March 2008 Table of Content 3 Notice 4 Package Content 5 Product Introduction 5 Product Features 6 Panel

More information

4830A Accelerometer simulator Instruction manual. IM4830A, Revision E1

4830A Accelerometer simulator Instruction manual. IM4830A, Revision E1 4830A Accelerometer simulator Instruction manual IM4830A, Revision E1 IM4830, Page 2 The ENDEVCO Model 4830A is a battery operated instrument that is used to electronically simulate a variety of outputs

More information

AT450SAW Programmable Selective Amplifier

AT450SAW Programmable Selective Amplifier AT450SAW Programmable Selective Amplifier LEMELETTRONICA srl Via Grezze 38 25015 Desenzano del Garda (BS) ITALY Tel. +39 030-9120006 Fax +39 030-9123035 www.lemelettronica.it Technical Specifications

More information

XTM72E & F Real-Time Clock Modules

XTM72E & F Real-Time Clock Modules Capricorn Controls Ltd Data & Application Notes Page 1 of 8 XTM72E & F Real-Time Clock Modules Originally designed to compliment our wide range of Gen-Set controls, these DC powered Real-Time-Clocks have

More information

Wireless Irrigation Controller. User Manual.

Wireless Irrigation Controller. User Manual. Wireless Irrigation Controller User Manual www.control-me.net www.waterme.com.au INTRODUCTION Introduction to WaterMe Thank you for purchasing a WaterMe Wireless Irrigation Controller. Nymet Australia

More information

with the Field-IQ Crop Input Control System

with the Field-IQ Crop Input Control System with the Field-IQ Crop Input Control System Quick Reference Card CONNECTING THE SYSTEM Ag25 GNSS antenna (P/N 68040-OOS) TNC/TNC right-angle cable (P/N 50449) Cable assembly, display to Field-IQ (P/N 50449)

More information

TORK DGU100/DGUM100 7 DAY DIGITAL TIME SWITCH INSTALLATION AND OPERATING INSTRUCTIONS READ INSTRUCTIONS CAREFULLY BEFORE SETTING UNIT

TORK DGU100/DGUM100 7 DAY DIGITAL TIME SWITCH INSTALLATION AND OPERATING INSTRUCTIONS READ INSTRUCTIONS CAREFULLY BEFORE SETTING UNIT TORK DGU100/DGUM100 7 DAY DIGITAL TIME SWITCH INSTALLATION AND OPERATING INSTRUCTIONS READ INSTRUCTIONS CAREFULLY BEFORE SETTING UNIT INSTALLATION UNIT IS TO BE INSTALLED BY A LICENSED ELECTRICIAN 1. To

More information

Sample BD Tech Concepts LLC

Sample BD Tech Concepts LLC XYZ Corp. Fry Controller FC-1234 Operating Specification Copyright 2014 Brian Dunn BD Tech Concepts LLC Contents Last Modified: 00/00/0000 Introduction 2 Interface 3 Idle 5 Cooking Cycle 5 Displaying and

More information

HSM-DUCTOR PNEUMATIC DUCTOR CONTROL SYSTEM KEYPAD QUICK REFERENCE

HSM-DUCTOR PNEUMATIC DUCTOR CONTROL SYSTEM KEYPAD QUICK REFERENCE HSM-DUCTOR PNEUMATIC DUCTOR CONTROL SYSTEM KEYPAD QUICK REFERENCE Systems Engineering Associates, Inc. 14989 West 69 th Avenue Arvada, Colorado 80007 USA Telephone: (303) 421-0484 Fax: (303) 421-8108 www.sea-seg.com

More information

Operation Guide 5554

Operation Guide 5554 MA1804-ED Contents Before Getting Started... Indicators Graphic Display Area Cycling Between Timekeeping Mode Digital Display Contents Navigating Between Modes Shifting the Hands Connecting with a Phone

More information

Professional 4-channel Thermocouple Thermometer plus Infrared Thermometer

Professional 4-channel Thermocouple Thermometer plus Infrared Thermometer Professional 4-channel Thermocouple Thermometer plus Infrared Thermometer TIF3340 BUTTONS = Power ON or OFF. = Steps through maximum (MAX), minimum (MIN), and average (AVG) readings. To exit MAX / MIN

More information

EZ Pro Instructions Zone Chart

EZ Pro Instructions Zone Chart EZ Pro Instructions Zone Chart 1 13 2 14 3 15 4 16 5 17 6 18 7 19 8 20 9 21 10 22 11 23 12 24 Part No.: 90007357 Revision No.: RV2 Date: July 2014 8600 Series Installation And Programming Guide Comparable

More information

imso-104 Manual Revised July 19, 2012

imso-104 Manual Revised July 19, 2012 imso-104 Manual Section 1 Getting Started SAFETY 1.10 Quickstart Guide 1.20 SAFETY 1.30 Compatibility 1.31 Hardware 1.32 Software Section 2 How it works 2.10 Menus 2.20 Analog Channel 2.21 On / Off 2.22

More information

The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.

The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional

More information

Inserting the batteries. Basic settings of the remote control

Inserting the batteries. Basic settings of the remote control Inserting the batteries Procedure prior to first use or when changing batteries Remove the back plate to expose the battery tray. Insert 2 x AA 1.5V alkaline batteries. Ensure the polarity of the batteries

More information

EAN-Performance and Latency

EAN-Performance and Latency EAN-Performance and Latency PN: EAN-Performance-and-Latency 6/4/2018 SightLine Applications, Inc. Contact: Web: sightlineapplications.com Sales: sales@sightlineapplications.com Support: support@sightlineapplications.com

More information

OWL micro+ WIRELESS ELECTRICITY MONITOR

OWL micro+ WIRELESS ELECTRICITY MONITOR COS T NOW TARIFF 3A SENDER 30 25 20 15 10 5 0 SETTING UP YOUR OWL Index of pages 2. Setting up date and time 3. Tariff setting 4. To set up a single tariff 5. To set up a two tiered time tariff 6. To set

More information

TDDFM14 OWNER S MANUAL

TDDFM14 OWNER S MANUAL TDDFM14 OWNER S MANUAL Table of Contents 3 Installation Features System Selector Switches 6 10 Connecting Wires and Mounting Thermostat 10 Operation (Programming) Programming/Setting Clock Personal Program

More information

MODULAR RESIDENTIAL AND COMMERCIAL IRRIGATION CONTROLLER. Water Days

MODULAR RESIDENTIAL AND COMMERCIAL IRRIGATION CONTROLLER. Water Days ICC2 MODULAR RESIDENTIAL AND COMMERCIAL IRRIGATION CONTROLLER System Off Date/Time Manual Start Times Solar Sync Run Times Seasonal Adjust Water Days Owner s Manual I2C-800-PL: 8-station base model, expandable

More information

User s Guide. ECx Features: Automatic Sprinkler System Timer

User s Guide. ECx Features: Automatic Sprinkler System Timer User s Guide Automatic Sprinkler System Timer ECx Features: Expandable Up To 8 Zones With Plug-In Modules Watering Programs With: - Calendar and Interval Days - 1 Min. to 4 Hrs. Valve Run Time - 4 Start

More information

GAUGEMASTER PRODIGY EXPRESS

GAUGEMASTER PRODIGY EXPRESS GAUGEMASTER PRODIGY EXPRESS DCC01 USER MANUAL Version 1.2 2014 1 T A B L E O F C O N T E N T S 1 Getting Started Introduction Specifications and Features Quick Start Connecting to Your Layout Running a

More information

PX1710M LCD Monitor USER S GUIDE

PX1710M LCD Monitor USER S GUIDE PX1710M LCD Monitor USER S GUIDE www.planar.com The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright.

More information

Instruction manual. DALI Gateway art Installation manual

Instruction manual. DALI Gateway art Installation manual Instruction manual DALI Gateway art. 01544 Installation manual Contents GENERAL FEATURES AND FUNCTIONALITY from page 5 ETS PARAMETERS AND COMMUNICATION OBJECTS from page 6 COMMUNICATION OBJECTS GENERAL

More information

Electronic 2-Circuit 24-Hour Time Switch With 100-Hour Backup

Electronic 2-Circuit 24-Hour Time Switch With 100-Hour Backup MODELS ET2125C, ET2125CR, ET2125CP Installation and Setup Instructions Electronic 2-Circuit 24-Hour Time Switch With 100-Hour Backup WARNING Risk of Fire or Electric Shock Disconnect power at the circuit

More information

Standard Digital Terminal High-Definition Digital Terminal. User Guide

Standard Digital Terminal High-Definition Digital Terminal. User Guide Standard Digital Terminal High-Definition Digital Terminal User Guide ILL-GDA-STD-001-0709 IN THIS GUIDE IMPORTANT RULES FOR SAFE OPERATION... 4 AVAILABLE ILLICO TERMINALS... 5 REMOTE CONTROLS... 17 CONNECTIONS...

More information

ZoneTouch V2 Zone Control System User Manual

ZoneTouch V2 Zone Control System User Manual ZoneTouch V2 Zone Control System User Manual www.polyaire.com.au 2014 Polyaire Pty Ltd II ZONEMASTER ZONETOUCH V2 ZONE CONTROL SYSTEM - User Manual TABLE OF CONTENTS 1) Features 2 2) Wall Controller Layout

More information

User s Guide. ECx Features: Automatic Sprinkler System Timer

User s Guide. ECx Features: Automatic Sprinkler System Timer TM User s Guide Automatic Sprinkler System Timer RAIN DELAY SEAS ADJUST ZE RUN TIMES AUTO / TIME / DAY WATERING DAYS PROGRAM TIMES PROGRAMS MANUAL NEXT ECx Features: Expandable Up To 8 Zones With Plug-In

More information

EVF 300 series. Controllers for electric bread and pizza ovens, with touch-keys, in split version and which can be integrated into the unit.

EVF 300 series. Controllers for electric bread and pizza ovens, with touch-keys, in split version and which can be integrated into the unit. EVF 300 series Controllers for electric bread and pizza ovens, with touch-keys, in split version and which can be integrated into the unit. Installer manual ENGLISH Code 144F300E114 Page 1 of 62 Important

More information

FRQM-2 Frequency Counter & RF Multimeter

FRQM-2 Frequency Counter & RF Multimeter FRQM-2 Frequency Counter & RF Multimeter Usage Instructions Firmware v2.09 Copyright 2007-2011 by ASPiSYS Ltd. Distributed by: ASPiSYS Ltd. P.O.Box 14386, Athens 11510 (http://www.aspisys.com) Tel. (+30)

More information

PQ-Box 100 Quick Start Instructions

PQ-Box 100 Quick Start Instructions PQ-Box 100 Quick Start Instructions These instructions are provided for the purpose on providing a quick start to PQ-Box 100 installation and operation. Please refer to the user handbook for full details.

More information