Digital differential Pressure switch Model DPS Instruction manual
|
|
- Willis Glenn
- 6 years ago
- Views:
Transcription
1 Digital differential Pressure switch Model DPS Instruction manual DPSeng_rev2 September 09 MECAIR S.r.l. Diaphragm Valves and Electronic Controls for Dust Collector Filters Via per Cinisello Nova Milanese Milano Italy Phone , Fax
2 DIGITAL DIFFERENTIAL PRESSURE SWITCH MODEL DPS INDEX 1. TECHNICAL DATA TABLE Page 1 2. ELECTRICAL CONNECTIONS Page 2 3. FUSES Page 3 4. PNEUMATIC CONNECTIONS Page 3 5. BOARD PANELS AND CONTROLS Page 4 6. START UP Page CONFIGURATION 4-20 ma Page 5 Page 7 9. TROUBLESHOOTING Page 7 ATTENTION: before using the product, carefully read this instruction manual in order to acquire a sufficient knowledge of the product itself. 1. TECHNICAL DATA TABLE Technical data Power supply V AC 50/60 Hz ±10% Fuse main Temperature Power Measuring range Unit Linearity Available languages Output 4-20mA Relays contacts Case protection Box Version DIN Version from panel board Dimensions Box Version DIN Version from panel board Weight Box Version DIN Version from panel board Upon request V 50/60 Hz AC ±10% 230 V = 100 ma T ; 115 V = 250 ma T 24 V = 630 ma T; 48 V = 315 ma T Storage -20 C/+80 C Operation -10 C/+50 C 3,5 230 V 0 10 kpa kpa; mmh2o; H2O; mbar; Inc H2O = measurement in inches with decimals notation Inc = measurement in inches with English notation ( 3 3/8 ) ± 0,25% of Full Scale Italian; English; French; German; Spanish Active or passive, selection through a jumper Supplied in active mode 5 A 230 V non inductive IP65 IP54 o IP65 with front transparent cover 150 X 225 h X 130 h 70 1,100 Kg 0,750 Kg 1
3 Do not expose directly to the sun in order to avoid uncontrolled temperatures to the circuits. Protect against rain, water infiltrations and moist. Do not install on vibrating walls. Use only cable gland with protection grade IP65 and of proper size ( according to the cable used ) It is compulsory to install downstream the power supply line a circuit breaker located closed to it and identified as the knife switch of the device Before opening the unit, be sure that unit is switched off and wires on clamps disconnected, including connection to alarm / signal relays. Do not attempt to repair the instrument, but contact MECAIR! All the wiring must be carried out by skilled people to prevent any risks of electric shock or fire. All electrical connections must follow different paths vs all the other uses. WEEE This instrument must be disposed of as special industrial waste according to the existing norms N.B.: The numbers and the letters within square brackets [ ] indicate the positions on the drawings. 2. ELECTRICAL CONNECTIONS It is compulsory to install downstream the power supply line a circuit breaker located closed to it and identified as the knife switch of the device 1) Connect the power supply to the terminal [ C ] Neutral 115 V AC 50/60 Hz 230 V AC 50/60 Hz 2) Connect any equipment to the set relay terminal [ D ] Normally open Normally closed Common 3) Connect any audio/visible signals to the alarm relay terminal [ E ] (flashing light, siren) Normally open Normally closed Common 4) Output 4-20mA [ G ] + - 2
4 Contact shown are without power supply F A B C G D E COM N.C. N.O. COM N.C. N.O. 4-20mA- 4-20mA+ N.C. 230VAC 115VAC 0V 3. FUSES Name Dimensions Value Type Drawing Description F1 5 x ma T [ A ] Supply mains 230 V F2 5 x ma T [ B ] Supply mains 115 V F1 5 x ma T [ A ] Supply mains 48 V F2 5 x ma T [ B ] Supply mains 24 V In case of replacement, it is compulsory to respect the value indicated on the table 4. PNEUMATIC CONNECTIONS The instruments is supplied with two filtering taps to be used to connect the instrument and the areas to be measured. Use a 4/6 rilsan hose. 3
5 5. BOARD PANELS AND CONTROLS ESC ENTER 1 Display Displays Delta-P value, the setting and the messages 2 Enter key Allows to enter the menu items, and to confirm data after modifications 3 + key Increases the datum to be modified or changes options in the menu items. Displays the alarm messages 4 - key Decreases the datum to be modified or changes options in the menu items. Cancels the alarm messages 5 Esc key Allows to exit the menu pages 6 Set Led Switches on when the set value Set is exceeded 7 Alarm Led Switches on in case of alarm. Possible alarms are: the set Alarm value is exceeded 10 kpa value is exceeded over range -2 kpa~(negative) value is exceeded over range 8 Model DP Super 5 languages 5 units Min-max Delta-P Set alarm set Selection 4/20 ma Full scale from 1 to 10 Hour counter 4
6 6. START UP Connect the instrument to the power supply. When switching the unit on, the display [ 1 ] indicates the model followed by the equipment version; after 3 seconds, it will display the pressure value. 7. CONFIGURATION To enter the configuration menu, press Enter key [ 2 ] Press + key [ 3 ] to move to the following menu, - [ 4 ] to move to the previous menu. Press Esc key [ 5 ] to go back to the pressure value display. Language selection Unit Minimum value input Maximum value input Alarm value input Pressure delay from 0 to 25 Sec with second decimals adjustment Select one of the 5 programmed languages Press Enter [ 2 ] to display the selected language By pressing either + [ 3 ] or - [ 4 ] it is possible to select a language among the 5 available ones (ITALIAN; ENGLISH; FRANCAIS; DEUTSCH; ESPANOL) Press Enter [ 2 ] to go back to the menu after changing the setting. Select one of the 5 available units Press Enter [ 2 ] to display the selected unit By pressing either + [ 3 ] or - [ 4 ] it is possible to select a unit among the 5 available ones (kpa; mmh2o; H2O; mbar; inc) Press Enter [ 2 ] to go back to the menu after changing the setting. Minimum value below which the Set relay re-opens. Led [ 6 ] off Maximum value above which the Set relay closes. Led [ 6 ] on Value above which the alarm relay closes. Led [ 7 ] on Exceeding switching limit minimum time (pressure fluctuations for times shorter than that are ignored ) 5
7 4-20 ma Full Scale Value from 1 to 10 that allows to select the maximum pressure value corresponding to 20 ma 4 ma adjustment 4 ma calibration of the adjusting datum, the 4-20 ma output emits a signal corresponding to 4 ma. decreased and therefore the output value is changed; adjust till the displayed value on the external instrument indicates the correct value 4 ma 20 ma adjustment 20 ma calibration of the adjusting datum, the 4-20 ma output emits a signal corresponding to 20 ma. decreased and therefore the output value is changed; adjust till the displayed value on the external instrument indicates the correct value 20 ma Zero pressure Sensor Zero setting Disconnect the hoses from the filtering taps before carrying out the Zero setting. Press Enter [ 2 ] to display the current pressure value By pressing + [ 3 ] the sensor is set to Zero and the Zero value is saved Press Enter [ 2 to go back to the parameter selection menu after changing the Connect the hoses to the filtering taps LCD Contrast To ad just the display contrast (0-63) of the parameter that adjusts the display contrast (0-63) decreased and the adjustment effects are visible on the display Press Enter [ 2 to go back to the parameter selection menu after changing the Hour counter xxxxx Displays the operating hours (Max ; cannot be modified) 6
8 ma It is possible to select the 4-20 output in either active or passive modes. Active: does not require any external feeder. Passive: it requires an external power supply between 18 / 24 V DC. Move the two jumpers on the 4-20mA card [ F ] to select either the active or the passive mode. The instrument is supplied in active mode. 9. TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION The display does not switch on Lack of power supply Check fuses F1 [ A ] or F2 [ B ] Check mains connections [ C ] Pressure value is not correct Disconnect the hoses from the pressure taps. If the value is not zero, carry out a Reset the pressure value, refer to the Zero Pressure item in the menu The value transmitted by the 4-20 ma is not correct or is lacking Display shows over range Led alarm lights. Zero setting. Wrong parameter adjustments Wrong active/passive mode selection DP is exceeded 10kpa DP is exceeded -2kpa~(negative) Input correct parameters, see menu: Full Scale ma adjustment 20 ma adjustment Check the jumper position on the 4-20 ma card [ F ] Disconnect the hoses. Press - key Discover the cause. Disconnect the hoses. Press - key Invert the hoses. 7
9 8
Digital differential pressure controller Model DPD Instruction manual
Digital differential pressure controller Model DPD Instruction manual DPDeng_rev2 September 09 MECAIR S.r.l. Diaphragm Valves and Electronic Controls for Dust Collector Filters Via per Cinisello 97 20054
More informationOperating instructions Electronic preset counter Type series 717
Operating instructions Electronic preset counter Type series 717 1. Description 5.98.3_gb 6-digit adding/subtracting counter with two presets Very bright 8mm high LED display Counting and preset range
More informationMF-PFT. Programmable differential pressure transmitter for pressure or flow measurement and control. DIL1 Output/Utsignal
Operating and installation manual Programmable differential pressure transmitter for pressure or flow measurement and control. MF-PFT Instruction : Mi-202gb_060907 NOTE! Read the entire instruction carefully
More informationTRANSCENSION 6-CHANNEL DMX DIMMER PACK (order code: BOTE40) USER MANUAL
www.prolight.co.uk TRANSCENSION 6-CHANNEL PACK (order code: BOTE40) USER MANUAL SAFETY WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! CAUTION! Keep this
More informationINDEP. QUARTZ MIN. - 1/2 MIN. AFNOR / IRIG B DHF / RADIO
Style 12 INDEP. QUARTZ MIN. - 1/2 MIN. AFNOR / IRIG B DHF / RADIO INSTALLATION AND OPERATING INSTRUCTIONS B.P. 1 49340 TRÉMENTINES FRANCE Tél. : 02 41 71 72 00 Fax : 02 41 71 72 01 www.bodet.com Réf. :
More informationElectronic converter for level transmitters MT03L Instructions manual
Electronic converter for level transmitters MT03L Instructions manual R-MI-MT03L Rev.: 1 English version PREFACE Thank you for choosing the MT03L converter from MT03 series of Tecfluid S.A. This instruction
More informationMT03A Electronic converter for flow rate transmitters
Instructions manual MT03A Electronic converter for flow rate transmitters The art of measuring R-MI-MT03A Rev.: 0 English version PREFACE Thank you for choosing a Tecfluid S.A product. This instruction
More informationMG-XV operating instruction. Measuring of norm signals, 4-8-digit. Panel instrument type MG-BV Construction instrument type MG-AV
MG-XV operating instruction Measuring of norm signals, 4-8-digit Panel instrument type MG-BV Construction instrument type MG-AV Contents 1. Brief description... 3 2. Safety instructions... 3 2.1. Proper
More informationUser Manual CC DC 24 V 5A. Universal Control Unit UC-1-E. General Information SET. Universal Control Unit UC-1 Of Central Lubrication PAUSE CONTACT
Universal Control Unit UC-1-E User Manual General Information Universal Control Unit UC-1 Of Central Lubrication CC DC 24 V 5A / M 15 SL /MK 31 M Z 30 General Information Contents Universal Control Unit
More informationStandard RS232 RS ma
1 / 5 CONTROL AND VISUALIZATION OF AC CURRENT IN SINGLE PHASE LINES BY EXTERNAL SHUNT Function Operating mode Current control Frequency control DC component control Shunt Timer Resolution Current precision
More informationEVF 300 series. Controllers for electric bread and pizza ovens, with touch-keys, in split version and which can be integrated into the unit.
EVF 300 series Controllers for electric bread and pizza ovens, with touch-keys, in split version and which can be integrated into the unit. Installer manual ENGLISH Code 144F300E114 Page 1 of 62 Important
More informationCET DOUBLE COUNTER WITH TWO THRESHOLDS LBM62CD. Type: TECHNICAL FEATURES
CET DOUBLE COUNTER WITH TWO THRESHOLDS Type: LBM62CD 6 DIGITS DOUBLE DIGITAL COUNTER WITH TWO SEPARATE COUNT IMPUTS LBM62CD counter is a double counter with two separate counters. Each counter s input
More informationCOMPANY. MX 9000 Process Monitor. Installation, Operating & Maintenance Manual AW-Lake Company. All rights reserved. Doc ID:MXMAN082416
COMPANY MX 9000 Process Monitor Installation, Operating & Maintenance Manual 2016 AW-Lake Company. All rights reserved. Doc ID:MXMAN082416 1 Table of Contents Unpacking...3 Quick Guide...3 Connect to Sensor...3
More informationAK-PVE4 Operating Instructions. Measuring of norm signals in wall-type units. Performance:
AK-PVE4 Operating Instructions Measuring of norm signals in wall-type units 1 2 P Performance: Digit heights: 20 mm Colour: red Display range: -999 9999 Wall-type housing: light grey made of ABS-plastic
More informationPLC Control Unit for a CSM-E Electrical Compact Clean Steam Generator
3.635.5275.254 IM-P486-18 CH Issue 3 PLC Control Unit for a CSM-E Electrical Compact Clean Steam Generator Installation, Start-up and Operation Manual 1. Safety information 2. General product information
More informationUNIVERSAL DIGITAL METER DC Volts and Amps AC RMS Volts and Amps Thermocouples and RTDs Process Signals Strain Gauge and Load Cell
99 Washington Street Melrose, MA 02176 Fax 781-665-0780 TestEquipmentDepot.com UNIVERSAL DIGITAL METER DC Volts and Amps AC RMS Volts and Amps Thermocouples and RTDs Process Signals Strain Gauge and Load
More informationVorne Industries. 87/719 Analog Input Module User's Manual Industrial Drive Itasca, IL (630) Telefax (630)
Vorne Industries 87/719 Analog Input Module User's Manual 1445 Industrial Drive Itasca, IL 60143-1849 (630) 875-3600 Telefax (630) 875-3609 . 3 Chapter 1 Introduction... 1.1 Accessing Wiring Connections
More informationStandard signal metering in wall-mounting case
User manual AKV-2VR4C Standard signal metering in wall-mounting case Technical features: Digit height: 20 mm Colour: red Range of display: -999 9999 Wall-mounting case: black, made of ABS-plastic Protection
More informationVLC-3 USER'S MANUAL. Light Program Controller. M rev. 04 K rev. 00 & ( ( 5, 352*5$0 1 : $ 2 ' 6(77,1*6 )81&7,216
Light Program Controller VLC-3 USER'S MANUAL +50,1 +50,1 1 : $ ' 2 7. 6 8 ' 5, 7 6 6. $ ( 3 352*5$0 0,16(& )81&7,216 6(77,1*6 & 8 5 5 ( 1 7 3 ( 5, 2 ' M 890-00189 rev. 04 K 895-00406 rev. 00 GENERAL...
More informationPanel cutout required: 1.772" x 3.622" (45mm x 92mm) 1.76" (45mm) 2.45" (62mm) 3.20" (81mm) 3.60" (91mm) 0.59" (15mm) Special Features
NEMA4X, IP65 Front Bezel Meter with Relays Option RELAY2 RELAY1 24V OUT POWER 4 3 2 1 6 5 2 1 2 1 NO NC COM NO NC COM RTD TC P P RTD 3 4 1 2 5 TC 6 SWITCH Rear View Gasket APM765 Panel Meter Description
More informationOperating Instructions
Operating Instructions Vacuum Transmitters for Diaphragm & Pirani Sensors 24 VDC Power With Pirani Sensors.01 to 100 mtorr.01 to 100 X 10-3 mbar.001 to 13.3 Pa 1 to 2000 mtorr.001 to 2 mbar 0.1 to 200
More information1 Output 1 operation. 3 Pressure unit display. 4 Main display Large 4-character LCD display. 5 Sub-display Small 4-character LCD display.
ure Sensor DP-100 Series INSTRUCTI MANUAL High-performance Digital Display For use outside Japan MEUML-DP100 V1.1 Thank you for purchasing products from Panasonic Electric Works SUNX Co., Ltd. Please read
More informationORDERING Page 6 BASLER RELAY STANDARDS, DIMENSIONS, ACCESSORIES Request bulletin SDA
BE1-59NC CAPACITOR NEUTRAL OVERVOLTAGE RELAY The BE1-59NC Capacitor Neutral Overvoltage Relay provides sensitive protection for capacitor banks. ADDITIONAL INFORMATION INSTRUCTION MANUAL ADVANTAGES Helps
More informationPhotoelectrics Through-beam Type PA18C.T..., DC
Photoelectrics Through-beam Type, DC Miniature sensor range Range: 20 m (Axial), 16 m (Radial) Sensitivity adjustment by potentiometer Modulated, infrared light 850 nm Supply voltage: to 30 VDC Output:
More information2 WIRE - LOOP POWERED TRANSMITTER FOR PT100 AND NI100 PROBES
EN K20RTD 2 WIRE - LOOP POWERED TRANSMITTER FOR PT00 AND NI00 PROBES General Description The K20RTD instrument converts a temperature signal read by a PT00 (EN 60 75) or NI00 probe with connection by 2,
More informationTABLE OF CONTENTS. Instructions:
TABLE OF CONTENTS Instructions: 1 Overview 1 2 Main technical parameters 1 3 Display and keyboard 2 3.1 Display Window 2 3.2 Indicator 4 4. Operation 4 4.1 Power 4 4.2 Zero 4 Modified 4 4.3 Modified 4
More informationREGO Start&Go USER MANUAL
REGO Start&Go USER MANUAL Version 0 Rev. B of 03/03/16 Page 1 of 15 Introduction The purpose of the manual is to describe all of the steps required to commission and correctly operate the REGO Start&Go
More informationSAUTER flexotron RDT405 Manual
SAUTER flexotron 400 - RDT405 Manual P100012100 Table of contents DISCLAIMER The information in this manual has been carefully checked and is believed to be correct. Fr. Sauter AG however, makes no warranties
More informationProcess Transmitter RMA 422
Technical Information TI 072R/24/ae Process Transmitter RMA 422 Multi-functional 1-2 channel top hat DIN rail unit with loop power supply, alarm set point monitoring, mathematics function and 1-2 analog
More informationCapacitance Limit Detection nivotester FTC 420/421/422
Technical Information TI 127F/00/en Capacitance Limit Detection nivotester FTC 420/421/422 Limit switches in Minipac design for liquids and bulk solids Application Nivotester FTC 420...422 capacitive limit
More informationOP5. Preprogrammed, configurable controller for simple applications
sect. pos. revision 3 020 08 2007 OP5 Preprogrammed, configurable controller for simple applications Optigo 5 is a new preprogrammed, configurable controller intended for DIN-mounting that can be set to
More informationUNIGAS Hand-held combustion gas analyzer with 3 sensors
UNIGAS 2000 Hand-held combustion gas analyzer with 3 sensors Unigas 2000+ is a professional flue gas analyser for 3 gases: O 2, CO & NO with electrochemical sensors, plus CO 2 and NO x calculated. Description
More information800 Displaying Series Flowmeter
TECHNICAL PRODUCT INSTRUCTION SHEET 800 Displaying Series Flowmeter OVERVIEW The principle of operation is very simple. A jet of liquid is directed at a free running Pelton wheel turbine in a specially
More information1.5mm amplitude at 10 to 55Hz frequency in each X, Y, Z direction for 2 hours 500m/s² (approx. 50G) in each X, Y, Z direction for 3 times
Color Mark Color Mark Feature Outstanding color matching accuracy - RGB light emitting diodes and 12-bit resolution - 2 detection modes (color only / color + intensity) - -step sensitivity adjustment for
More informationElectronic Panel Meters DIGEM Preference Program Process control, automation & laboratory uses Class 0.01 to 1 Current, Voltage, Frequency,
Electronic Panel Meters DIGEM Preference Program Process control, automation & laboratory uses Class 0.01 to 1 Current, Voltage, Frequency, Temperature, RPM, Pressure, etc. LED/ LCD displays 1999 to 99999
More informationDS 400 P. Intelligent Electronic Pressure Switch in Hygienic Stainless Steel Ball Housing. on hygienic process connections
Intelligent Electronic Pressure Switch in Hygienic Stainless Steel Ball Housing Description The electronic pressure switch is the successful combination of hygienic process connections with flush welded
More informationOperating Instructions (ed. 5.97) Electronic Preset Counter Type Series 904
Operating Instructions 3.96.3 (ed. 5.97) Electronic Preset Counter Type Series 904 1. Description 6 digit preset counter, 2 presets, add./subtr. bright 2-line LCD display with symbols for activated outputs
More informationGC30 Digital Differential Pressure Gauge Operation Manual
TY-GC30-001A GC30 Digital Differential Pressure Gauge Operation Manual NAGANO KEIKI CO., LTD 2004.02.12 For safety of use TY-GC30-001A In order to safely and correctly utilize this device, please read
More informationSpectra Flood Q40. Exterior Fixture User Manual. Order code: LEDJ Version LEDJ284N - 15 Version
Spectra Flood Q40 Exterior Fixture User Manual Order code: LEDJ284-40 Version LEDJ284N - 15 Version Safety advice WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL
More informationLevel Measurement silometer FMC 420, FMC 423
Technical Information TI 077F/00/en Level Measurement silometer FMC 420, FMC 423 For connecting to capacitance probes or Deltapilot S hydrostatic probes Main applications The is used for continuous level
More informationE8Y. Micropressure Sensor with Easy-to-Read Digital Display. Differential Pressure Sensor. Ordering Information. Sensors
Differential Sensor Micropressure Sensor with Easy-to-Read Digital Repeat accuracy of ±1% FS (setting resolution: 0.01 kpa), high-precision pressure control available. Compact design (31 mm) saves mounting
More informationTABLE OF CONTENTS SPECIFICATIONS...1 MOUNTING...3 WIRING...4 THEORY OF OPERATION...6 MILIVOLT INPUT OPTION JUMPER SELECTIONS...7
TABLE OF CONTENTS SPECIFICATIONS...1 MOUNTING...3 WIRING...4 THEORY OF OPERATION...6 MILIVOLT INPUT OPTION JUMPER SELECTIONS...7 FRONT PANEL OPERATIONS...8 PROGRAMMING FLOW CHART...8 DEFINITIONS OF MENU
More informationWIRING. Connection connector. NPN output type Standard type. Main circuit. High-function type. Main circuit. PNP output type.
INSTRUCTI MANUAL Sensor High-performance Digital Display DP-1 Series Thank you very much for using SUNX products. Please read this Instruction Manual carefully and thoroughly for the correct and optimum
More informationInstallation and User Guide 458/CTR8 8-Channel Ballast Controller Module
Installation and User Guide 458/CTR8 8-Channel Ballast Controller Module Helvar Data is subject to change without notice. www.helvar.com i Contents Section Page Introduction 1 Installation 2 1. Attach
More informationDescription. Specifications and Ordering Information 1900/27 Vibration Monitor
R Specifications and Ordering Information 1900/27 Vibration Monitor Description The 1900/27 is a single-channel, stand-alone, locally mounted vibration monitor. It can be used as a stand-alone machinery
More informationTDEPD. Field-Programmable Pressure Switch/Transducer with Integrated LED Display. Programming Sequence Manual
TDEPD Field-Programmable Pressure Switch/Transducer with Integrated LED Display Programming Sequence Manual Wiring Diagram Pin5 Maintenance Mode + Gray Vent Pin2 Digital Output 2 +/ Analog Output + White
More informationPBC series. RoHS. Ready. IEC-Type Contactors & Accessories 9-80 Amp AC-3, Amp AC-1 AC Coils. P&B PBC Series IEC Type Contactors & Accessories
PBC series IEC-Type Contactors & Accessories 9-80 Amp AC-3, 25-125 Amp AC-1 AC Coils File E38802 (PBC) RoHS Ready Users should thoroughly review the technical data before selecting a product part number.
More informationNoise Detector ND-1 Operating Manual
Noise Detector ND-1 Operating Manual SPECTRADYNAMICS, INC 1849 Cherry St. Unit 2 Louisville, CO 80027 Phone: (303) 665-1852 Fax: (303) 604-6088 Table of Contents ND-1 Description...... 3 Safety and Preparation
More informationMetric Series. PXM409 Differential Series. mv/v, 0 to 5 or 0 to 10 Vdc, or 4 to 20 ma Outputs Uni-Directional Ranges 0-25 mbar to 0-70 bar
Micro-Machined Silicon Transducers wet/dry differential mv/v, 0 to 5 or 0 to 10 Vdc, or 4 to 20 ma Outputs Uni-Directional Ranges 0-25 mbar to 0-70 bar PXM409 Differential Series U 5-Point NIST Traceable
More informationTroubleshooting. 1. Symptom: Status indicator (Red LED) on SSR is constant on. 2. Symptom: Output indicator (Yellow LED) on SSR is flashing.
Product Data Electrical Data SST (Transmitter) SSR (Receiver) Supply voltage 18 30 V dc Max. Voltage ripple 15 % (within supply range) Current consumption 100 ma (RMS) 75 ma Digital - 100 ma Max. outputs
More informationModel IQ4-PC User Manual Revision Date:
Basic Specifications Supply Volts 230V 50/60Hz ±15% 115V 50/60Hz ±15% 24V DC (isolated) ±15% Power Consumption Max. 3VA (IQ4-PC-R0) Max. 6VA (IQ4-PC-R2-PSI24-RT) Operating Temperature -5 ~ +60 C Operating
More informationPressure Sensor. Ordering Information. Mini-Cube Pressure Sensor with Easy-to-Read LED Display
Sens Mini-Cube Sens with Easy-to-Read LED Display Industry s smallest, lightest l Both analog bar and digital pressure values are displayed Two independent outputs plus one analog output are available
More informationCURRENT INJECTION RELAY TESTER CR-100. ( Code P60212 (770081) ) INSTRUCTIONS MANUAL ( M / 05A ) (c) CIRCUTOR S.A.
CURRENT INJECTION RELAY TESTER CR-100 ( Code P60212 (770081) ) INSTRUCTIONS MANUAL ( M 981 329 / 05A ) (c) CIRCUTOR S.A. ---- CURRENT- TIME TRIP TESTER CR-100 --------------- Page. 2 CURRENT INJECTION
More informationHS-509 VIBRATION TRIP MODULE
HS-509 VIBRATION TRIP MODULE 1. Overview The HS-509 is a configurable trip amplifier capable of accepting a 4-20mA signal from a HS-420 sensor and providing two trip action relay outputs along with an
More informationLMP 331 LMP 331. Screw-In Transmitter with piezoresistive Stainless Steel Sensor
LMP Screw-In Transmitter with piezoresistive Stainless Steel Sensor flush diaphragm hydrostatic level measurement of clean, thin fluid media nominal pressure ranges from 0... 40 mbar up to 0... 40 bar
More informationElectronic converter for flowmeters MT03F Instructions manual
Electronic converter for flowmeters MT03F Instructions manual R-MI-MT03F Rev.: 0 English version PREFACE Thank you for choosing the MT03F converter from MT03 series of Tecfluid S.A. This instruction manual
More informationPilot Valves and Nema 4 Enclosures. Innovative Environmental Solutions
Pilot Valves and Nema 4 Enclosures Innovative Environmental Solutions Technical Specification Q Series Solenoid Solenoid used in the remote or integral actuation of dust collector diaphragm or pilot valves.
More informationHerzlich Willkommen Bienvenue Welcome. General Basics JUMO Screen Recorders. Manfred Schleicher
Herzlich Willkommen Bienvenue Welcome General Basics JUMO Screen Recorders Manfred Schleicher Advices for the presentation This presentation shows important functions of JUMO- Screen Recoders and demonstrates
More informationRD RACK MOUNT DIMMER OWNERS MANUAL VERSION /09/2011
RD - 122 RACK MOUNT DIMMER OWNERS MANUAL VERSION 1.3 03/09/2011 Page 2 of 14 TABLE OF CONTENTS UNIT DESCRIPTION AND FUNCTIONS 3 POWER REQUIREMENTS 3 INSTALLATION 3 PLACEMENT 3 POWER CONNECTIONS 3 OUTPUT
More informationM150SP USER S AND INSTALLER S MANUAL. v2.0 REV. 03/2017
M150SP USER S AND INSTALLER S MANUAL v2.0 REV. 03/2017 00. CONTT 01. SAFETY INSTRUCTIONS INDEX 01. SAFETY INSTRUCTIONS STANDARDS TO FOLLOW 02. THE DEVICE TECHNICAL SPECIFICATIONS VISUAL ASPECT CONNECTORS
More informationSolid-State Digital Timer
Solid-State Digital Timer 1/16 DIN, Digital-Set Timer with 0.1 Second to 9,990 Hours Range 8 field-selectable operation modes Universal AC/DC supply voltage timers available Operations include ON-delay,
More informationElectronic Panel Meters DIGEM Preference Program Process control, automation & laboratory uses Class 0.01 to 1 Current, Voltage, Frequency,
Electronic Panel Meters DIGEM Preference Program Process control, automation & laboratory uses Class 0.01 to 1 Current, Voltage, Frequency, Temperature, RPM, Pressure, etc. LED/ LCD displays 1999 to 99999
More informationRF Wireless Receiver (Model S4PU-DC-ANT3)
RF Wireless Receiver (Model 0020445 S4PU-DC-ANT3) Package Include: 1 Reciver S4PU-DC06-ANT3 / S4PU-DC09-ANT3 / S4PU-DC12-ANT3 / S4PU-DC24-ANT3 1 User Manual Feature: Application: It can be used in industry
More informationMicro-Machined Silicon Transducers
Micro-Machined Silicon Transducers wet/wet differential Pressure Models mv/v, 0 to 5 or 0 to 10 Vdc, or 4 to 20 ma Outputs Uni-Directional Ranges 0-25 mbar to 0-70 bar PXM409 Differential Series Standard
More informationFIELD MOUNTED RATE TOTALISER MODEL 202D
FIELD MOUNTED RATE TOTALISER MODEL 202D 16 June 2003 Introduction 1 1. INTRODUCTION The Model 202Di Rate Totaliser is a microprocessor based instrument which accepts a frequency or pulse input from
More informationFigure 1: Standard 906 Sensor and Pulser Disc. Figure 2: Standard 906 Sensor and Pulser Wrap
Description: The TR5000 is a Full Logic Control Process ratemeter that can display up to three separate values of rate and compare them to programmable set points. Rates A & B can be programmed by the
More informationAE-341 SERIES PROCESS INDICATORS 2 TO 6 DIGITS 0-20 MA, 4-20 MA, 0-5V, OR 0-10V SCALED INPUT
FN: 341MAN1.DOC AE-341 SERIES PROCESS INDICATORS 2 TO 6 DIGITS 0-20 MA, 4-20 MA, 0-5V, OR 0-10V SCALED INPUT DESCRIPTION AE Series Process Indicators are available with 1", 2.3", 4", 8", or 12" high digits,
More informationDragonfly Quad. User Manual V1.4. Order code: EQLED101
Dragonfly Quad User Manual V1.4 Order code: EQLED101 Safety advice WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! Before your initial start-up, please
More information02/11/2015
DIN Rail Mount 17.5 mm MUS/MUSF 80 AC/DC Part number 84872141 Control relays monitoring their own power supply - MUS : Over/undervoltage control Selectable latching (memory) function - MUSF : Over/undervoltage
More informationHenkel Installation Handbook LINEGUARD 2001
Henkel Installation Handbook LINEGUARD 2001 HENKEL ITALIA S.r.l. Microprocessor instruments Henkel Installation Handbook Lineguard 2001 Page 2 Summary 1. The Microprocessor Instruments... 4 1.1. Norms
More informationTEK-LCD 7801A. NEMA 4X Loop-Powered Feet and Inches Level Meter. ACCESSORIES. Technology Solutions
Technology Solutions TEK-LCD 7801A NEMA 4X Loop-Powered Feet and Inches Level Meter ACCESSORIES www.tek-trol.com Flow Level Temperature Pressure Valves Analyzers Accessories TekValSys Introduction The
More informationJunior Max (JR Max ) Controller
Get more done TM Junior Max (JR Max ) Controller stations Operating Instructions Thank you for purchasing this advanced, highly featured Irritrol Junior MAX controller. The Junior MAX is the latest addition
More information9 Control Equipment. Measurement- and Control Equipment Series 8214, 8218
9 Control Equipment Measurement- and Control Equipment Series, Explosion protection to CENELEC IEC Can be used in Zone 1 and Zone 2 Designed for panel mounting Enclosure material : Polyester resin : Aluminium,
More informationE R A I GATE OPENERS DEPARTMENT
S E R A I GATE OPENERS DEPARTMENT INSTALLATI OF THE CTROL PANEL CR/41 WHERE PLACING THE CTROL PANEL Place the device near the gate, in order to have the minimum lenght of the cables for connection with
More informationInstallation and Setting up Instructions for the 990 Signal Conditioning Instrument
Installation and Setting up Instructions for the 990 Signal Conditioning Instrument Contents Page 1.0 Overview... 3 2.0 Installation.. 4 2.1 Electrical connections... 4 2.2 Cable selection... 4 2.3 Electrical
More informationDMP 331i DMP 333i. Precision Pressure Transmitter. Stainless Steel Sensor. accuracy according to IEC 60770: 0.1 % FSO
DMP i DMP i Precision Pressure Transmitter Stainless Steel Sensor accuracy according to IEC 600: 0. % FSO from 0... 00 mbar up to 0... 600 bar Output signal wire:... 0 ma wire: 0 0 V others on request
More informationMULTIS L72. Operating instructions
GB MULTIS L72 Operating instructions 2 SOCOMEC - Ref. : 876 091B ENGLISH GB Contents PRELIMINARY OPERATIONS 4 GENERAL INFORMATION 5 PRESENTATION 4 INSTALLATION 5 Mechanical environment Climatic environment
More informationCONTROL VISIO 0033 (0) ASSISTANCE ACCESSORIES SUPERVISION WALL UNIT INTEGRATION. Direct line
CONTROL VISIO ASSISTANCE Our qualified technicians are at your disposal for: Electronics signals of medical gas networks by VISIO concept, (ISO 7396 norm) is the solution to prevent any defaults of medical
More information17 19 PROFESSIONAL LCD COLOUR MONITOR ART
17 19 PROFESSIONAL LCD COLOUR MONITOR ART. 41657-41659 Via Don Arrigoni, 5 24020 Rovetta S. Lorenzo (Bergamo) http://www.comelit.eu e-mail:export.department@comelit.it WARNING: TO REDUCE THE RISK OF FIRE
More information- special pressure ranges - variety of electrical and mechanical. Characteristics. - other versions on request
DMP Industrial Pressure Transmitter for Low Pressure piezoresistive stainless steel sensor O p t i o n : f l u s h v e r s i o n accuracy: 0.75 %, 0.5 %, 0.0 %, 0.05 % FSO BFSL (0.5 %, 0.5 %, 0. %, 0.
More informationDTV742 Installation Quick Start Guide
DTV742 Installation Quick Start Guide The Wegener Model DTV742 8VSB 4-Channel Multiplexor receives VHF/UHF broadcast HDTV signals and provides output ASI streams for connection to cable system QAM modulators.
More informationVeeder-Root brand Series C628 Dual Preset Counter (C628-8XXX) Technical Manual
Introduction Your Veeder-Root brand C628 Dual Preset Counter is one model in a family of 1/8 DIN units which offers breakthrough display technology as well as easy-to-program single-line parameters. Designed
More informationLinear flow control with actuator IFC
Linear flow control with actuator Product brochure GB 3 Edition 01.14 Linear relationship between adjustment angle and flow rate Large control ratio of 25:1 EC type-tested and certified Actuators IC 20
More informationElectronic Pulse Counter Combination device
Electronic Pulse Counter Combination device measuring monitoring analysing Input: pulse counter, time meter Display: 6-digit LED Height of digits: 14/8 mm Operation with front-panel buttons Material: plastic
More informationSONARtrac Technical Bulletin
Page 1 of 14 Purpose: The purpose of this document is to formally release the SONARtrac TM Troubleshooting. The guide lists problems that may be encountered by personnel installing SONARtrac TM meters
More informationABB MEASUREMENT & ANALYTICS DATA SHEET. AZ100 series Zirconia oxygen analyzer for small boiler applications
ABB MEASUREMENT & ANALYTICS DATA SHEET AZ00 series Zirconia oxygen analyzer for small boiler applications AZ 00 SE RIE S Z I RCON I A OX YG EN ANALY ZE R FOR SMALL BOILE R APPLIC ATIONS DS/AZ00-E N RE
More informationK3NX Process Meter OPERATION MANUAL
Cat.No. N90 E1 1 K3NX Process Meter OPERATION MANUAL K3NX Process Meter Operation Manual Produced January 1998 Notice: OMRON products are manufactured for use according to proper procedures by a qualified
More informationSCALE & WEIGHT DISPLAYS
The MICRO SERIES SCALE & WEIGHT DISPLAYS LARGE DIGIT MODELS Mighty-5S DPM MODELS Micro-S & Mighty-1S Mighty-1S Micro-S ELECTRO-NUMERICS, INC. Introduction The Electro-Numerics family of Digital Panel Meters
More information02/11/2015
24 x 48 Totalizers CTR24 non-backlit model Part number 87622062 Display : 8-digit LCD, height 8 mm Powered by a lithium battery Counter inputs : solid state (4-30 VDC) or voltage (10 260 VAC) Reset on
More informationLabel Applicator HERMA 400
Label Applicator HERMA 400 Info GB V6.0 / 30.3.07 [ Facts & Data ] R Constructional variant Right-hand or left-hand version, always flexible to use L Power supply / Line voltage Max. power consumption
More informationDS 200 P DS 200 P. Electronic Pressure Switch with Flush Process Connection
with Flush Process Connection piezoresistive pressure sensor up to independent contacts, configurable optional: analogue output Exprotection (for wire) cooling element up to 00 C nominal pressure ranges
More informationTempus Lux Digital Photoelectric Switch D GB CZ BZT Installation and operating instructions BZT27731
2 310380 01 Tempus Lux Digital Photoelectric Switch BZT27731 GB 0 6 12 18 24 Installation and operating instructions MENU OK 2 Lux 2000 BTZ27731 1 D GB CZ PL HR 1-2 2600 W 1-2-3 16A-10AX 250V~ 0,5mm -
More informationUSER MANUAL. Compact dimensions 6 DIN modules, with 4 LED s display with 7 segments, for an excellent reading of the measurements
DUCATI SISTEMI S. P. A. DUCA47 USER MANUAL Introduction The instrument DUCA47 is a digital multimeter that allows the measurement of the principal electrical parameters in threephase 230/400Vac networks
More informationSet Point Controller OC557. Operator s Manual
OC557_Manual_GB1206D Set Point Controller OC557 4 20mA Input Operator s Manual METRIX ELECTRONICS LTD. Tel: +44 (0)845 034 3234 Minchens Court, Minchens Lane Fax: +44 (0)845 034 3233 Bramley, Tadley, Hampshire
More informationMagnecraft Power Relays
Description DPST-NO, 30 A; DPDT, 30 A (NO) / 3 A (NC) Description The series power relays offer a small package size and features Class F insulation for a maximum coil temperature of 55 C (3 F). These
More informationED3. Digital Encoder Display Page 1 of 13. Description. Mechanical Drawing. Features
Description Page 1 of 13 The ED3 is an LCD readout that serves as a position indicator or tachometer. The ED3 can display: Speed or position of a quadrature output incremental encoder Absolute position
More informationINSTALLATION & USER GUIDE
INSTALLATION & USER GUIDE Digidim 458 8-Channel Dimmer STEP 1 Assemble Dimmer Unit STEP 2 Mount Dimmer Chassis STEP 3 Electrical Installation STEP 4 Attach Module and Make Connections STEP 5 Replace Cover
More informationAchat 115 Sub A active subwoofer. user manual
Achat 115 Sub A active subwoofer user manual Musikhaus Thomann Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Deutschland Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet: www.thomann.de
More informationFusion 120 Zoom. User Manual. Order code: EQLED068
Fusion 120 Zoom User Manual Order code: EQLED068 Safety advice WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! Before your initial start-up, please make
More informationAssembly. Front view. LEDs. Parametrization interface. Power Bus
otation Speed Monitor Features Assembly 1-channel signal conditioner 2 V DC supply Input for 2- or -wire sensors Input frequency 10 mhz... 50 khz elay contact output Start-up override and restart inhibit
More information