Industrial Diode Laser (IDL) System IDL Series

Transcription

1 COMMERCIAL LASERS Industrial Diode Laser (IDL) System IDL Series Key Features Round, top-hat beam profile for uniform power distribution Warranted for full rated power in either pulsed or continuous wave (CW) operation Air-cooled Fiber delivery Built-in red pointing laser diode Available 19" rack mount power supply configuration Applications Plastic welding Selective soldering Heat treatment Brazing Micro bending Hair removal Tissue welding The JDSU IDL Series provides up to 100 watts of multi-mode laser output by combining highly reliable, single-emitter laser diodes, fused fiber delivery, and a red pointing diode laser with a heat sink, power supply, and control electronics in one complete package. Long life expectancy is a primary benefit of the IDL series. These lasers incorporate multiple single-emitter diodes. Unlike bar diodes, single-emitter diodes operate relatively stress-free during pulsed operation and can be pulsed on and off without affecting lifetime. This is critical in many applications such as soldering and plastic welding. Also due to its all-in-glass design, contamination cannot accumulate inside the IDL system. The IDL Series is supplied with a 600 µm, 0.22 NA delivery fiber terminated with an SMA905 connector. An optional focusing termination provides a round, tophat beam profile that allows for uniform heat distribution at the work piece. The detachable termination focuses to a 600 µm spot diameter at a working distance of 85 mm. Designed for easy operation and installation, the IDL Series uses internal fans for cooling, features fiber delivery, and requires only standard wall-plug power. The laser can be monitored and controlled by customer-supplied interface electronics via a 40-pin analog connector or by RS232 computer control. NORTH AMERICA: JDSU (5378) WORLDWIDE: JDSU WEBSITE:

2 2 Dimensions Diagram (Specifications in inches [mm] unless otherwise noted.) Connector Locations Termination C (Optional) Dimensions Diagram (Specifications in inches [mm] unless otherwise noted.)

3 3 Typical Beam Profile IDL-50 Life Test Data Note: 50% duty cycle at 25 C

4 4 Specifications Parameter Specification Optical Rated CW output power 20 W, 50 W, or 100 W Wavelength ±10 nm, 940 ±10 nm, or 965 ±15 nm Spectral width, FWHM at full rated power <6 nm Optical noise, MHz, at >10 W output 1% rms Rise time/fall time (10% - 90%) <250 µs Output beam ellipticity 1.1:1 Beam quality 60 mm-mrad nominal With SMA 905 connector Fiber core diameter 600 µm Fiber NA <0.22 With optional termination module C Focused beam diameter at working distance 0.6 mm nominal Working distance 85 mm nominal Pointing diode laser Wavelength 635±10 nm Output power 0.8 mw nominal Electrical Input power 100 to 120 or 200 to 240 V AC, 50 to 60 Hz Control RS232 or analog input Mechanical Chassis weight 13.7 kg (30.2 lbs) typical Chassis dimensions (W x H x D) 333 x 168 x 381 mm (13.1 x 6.6 x 15.0 inches) Termination module C weight 1 kg (2.2 lbs) typical Termination module C dimensions (Ø x L) See dimensional diagram on page 2 Cool air flow Internal fan. At least 80 mm (3") clearance, both sides Fiber pigtail output length 6.7 m (22') typical Environmental Operating temperature range 5 to 35 C Operating humidity (non-condensing) 5 to 85% Storage temperature range -20 to 55 C Storage humidity (non-condensing) 5 to 95% nm also available, but at lower powers.

5 Ordering Information For more information on this or other products and their availability, please contact your local JDSU account manager or JDSU directly at JDSU (5378) in North America and JDSU worldwide or via at Sample: IDL (20 W rated output power, 915 nm wavelength) Associated Part: IDL-TERMC (optional focusing termination) User Safety Safety and Operating Considerations The IDL emits both Class IV radiation, which is invisible, and Class II radiation that is visible. Direct or scattered radiation can be harmful to the human eye. Proper laser safety eyewear must be worn during operation. All statements, technical information and recommendations related to the products herein are based upon information believed to be reliable or accurate. However, the accuracy or completeness thereof is not guaranteed, and no responsibility is assumed for any inaccuracies. The user assumes all risks and liability whatsoever in connection with the use of a product or its application. JDSU reserves the right to change at any time without notice the design, specifications, function, fit or form of its products described herein, including withdrawal at any time of a product offered for sale herein. JDSU makes no representations that the products herein are free from any intellectual property claims of others. Please contact JDSU for more information. JDSU and the JDSU logo are trademarks of JDS Uniphase Corporation. Other trademarks are the property of their respective holders JDS Uniphase Corporation. All rights reserved Rev /06 IDL.DS.CL.AE NORTH AMERICA: JDSU (5378) WORLDWIDE: JDSU WEBSITE: