SELENA GPS ATOMIC CLOCK ( Option # 725GPS )
|
|
- Benjamin Morton
- 6 years ago
- Views:
Transcription
1 SELENA ATOMIC CLOCK ( Option # ) Rev. GS34 ATOMIC CLOCK WITH ( Optional Feature ) ( option # ) In all Atomic clock with receiver option configurations the functions Fn 70 must be enabled. The Daylight Savings correction for US and Canada may be enabled by enabling the function Fn 60. In order to use the receiver option, the clock must have at least one or input port installed. In a MultiZone clock system, the zone offset may setup by enabling the function Fn 50 as described in the section: MultiZone Clock Systems. Many commercial receivers may be used with the Selena clocks as long as they are WAAS enabled and generate the NMEA 0183 standard sequences in the default mode at 4800 bps. However, it is advisable that the Selena receivers model or V be used for best results. In a multiclock MasterSlave configuration, one clock assigned as the Master may be connected to a receiver while other slave clocks may be synchronized with the Master by other methods as specified in the section: Master Slave Synchronized System Clock Networks. Similarly, more than one clock may be connected to the same receiver as long as the maximum, allowed load of the communication link is not exceeded. Activating the Atomic Clock option The function Fn 70 must be enabled. If external receiver is used, the receiver cable must be connected to the 4pin terminal block on the back panel of the clock as follows: model: V Black wire terminal on clock Black wire White wire terminal on clock Green wire No connection terminal on clock No connection Red wire terminal on clock Red wire If an extension cable is used between the receiver and the clock, it is important to keep the wire resistance of the and supply wires as low as possible. In most applications the cable does not have to be shielded. However, in an environment with a lot of electrical interference a shielded cable may be used. In such instance, connect the cable shield to the terminal. Note, that the Selena clock can indicate if it receives a valid time data from the. This indicator is the decimal dot after the forth digit in the time display. This indication is active as long as the function Fn 12 is enabled. At the first powerup the dot may come ON at the 50th second of each minute and stay on until the clock recovers a valid time data from the, or until the 00th second. Subsequently, the data is sampled once, each minute, beginning at the 50th second until the 00th second. As soon as the data is detected as valid, the dot will be turned off, until the next minute. This feature may be deactivated at any time by disabling the function Fn 12. Perform the following steps: 1. Place the receiver near, at or outside a window, so that it has unobstructed view of at least a part of the sky.. 2. Connect the receiver's cable to the clock terminal block. 3. Power up the clock. 1
2 4. After several seconds, the display will turn on and will show the time reading, which at this point, may not be accurate, depending if the clock was synchronized before and if it still has the backup charge enough to maintain the timekeeping without the supply power. Normally, the initial time recovery should not take longer than appx. 3 minutes. 5. After the clock receives the first valid data from the, the time will be synchronized with the Atomic Time and Date transmitted by the satellites. Depending upon the Time Zone settings in the clock ( see Fn 50 and Fn 51 ) and if the Daylight Savings is enabled ( see Fn 60 ), the time displayed by the clock may or may not be correct for the clock location. 6. From this point on, the clock will attempt to receive the time at the 50th second of each minute until the 00th second. The indicator dot, if enabled, will be turned on each time and turned off as soon as the data is received, which normally should take approximately 1 to 2 seconds. If necessary, the indicator dot function may be deactivated by disabling the function Fn Any of the clock functions or settings may be changed by the user at any time via the remote control. Note, that whenever the data becomes unavailable for whatever reason, the clock will automatically revert to its internal time base that was synchronized all the time when the data was most recently valid. Therefore the time accuracy will remain very high until the next time sync from the. When the clock supply is interrupted, the display will be automatically turned off, but the internal selfrecharging backup will continue accurate timekeeping for approximately 2 weeks on each charge. Full recharge takes approximately 30 minutes when the supply power is restored. Using the clock as the Master clock. In a multiclock MasterSlave configuration, the Master may be a clock with a receiver installed. In such case, one of the simplest configurations is achieved by linking the Master clock with all Slaves by wiring the or cable between the Master clock and the Slaves. That cable should be connected in parallel to all clocks and the Master clock should be setup as the Transmitter of the sync data by enabling the function Fn32 or certain other functions as explained in the section Master Slave Sync System with Serial Communication. If the Master clock and the Slaves have interface installed, the Transmit ( ) pin on the terminal in the Master clock should be connected to the Receive ( ) pin of the in all Slave clocks. Then the Slave clocks should be set as sync receivers by enabling the function Fn34 or by enabling the repeater functions as described in the section: Master Slave Sync Signal Range ExtenderRepeater. Note, that the ( Ground ) wire in the Master and all Slaves should also be wired up together. DO NOT connect any wires to the terminal. That supply is only for powering up the receiver unit itself. 1. In clocks with the alphanumeric ELECTRONIC TEXT / DATE display, consult the manual section: Date / Text and ZONE text display. The functions Fn80, 85 and Fn86 control the assignments of the electronic text. 2. During assigning of the ZONE TIME OFFSET or the ZONE TEXT, the operation of the SET key on the Remote Control is changed, depending if the function Fn86 or Fn51 are enabled. Never let both functions be enabled at the same time. 2
3 CLOCK SUPPLY SHOWN FIRST CLOCK AS THE MASTER ( Option and # 725 or # ) OR SLAVE CLOCKS WITH or ( option # 725 or # ) CONFIG. TYPE 1: ENABLE functions Fn34 and Fn70 in MASTER CLOCK ALL ZONES ENABLE functions Fn34 and Fn70 in ALL SLAVE CLOCKS TO MORE SLAVES IN THE NETWORK CONFIG. TYPE 2: ENABLE functions Fn34, Fn70 and Fn53 in MASTER ZONE ONLY ENABLE functions Fn34 ONLY in ALL SLAVE CLOCKS MASTER SLAVE SYSTEM WITH ATOMIC TIME RECEIVER and using SELENA clock as the MASTER. 3
4 CLOCK SUPPLY SHOWN OR ALL CLOCKS AS SLAVES ( Option ) ENABLE functions Fn34 and Fn70 in ALL CLOCKS and ZONES TO MORE SLAVES IN THE NETWORK MASTER SLAVE SYSTEM WITH ATOMIC TIME RECEIVER and using the Receiver as the MASTER. 4
5 CLOCK SUPPLY SHOWN FIRST CLOCK AS THE MASTER ( Option and # 725 or # ) OR CONFIG. TYPE 1: ENABLE functions Fn34 and Fn70 in MASTER CLOCK ALL ZONES CONFIG. TYPE 2: ENABLE functions Fn34, Fn70 and Fn53 in MASTER ZONE ONLY SLAVE CLOCKS WITH or ( option # 725 or # ) CONFIG. TYPE 1: ENABLE functions Fn34 and Fn70 in ALL SLAVE CLOCKS CONFIG. TYPE 2: ENABLE functions Fn34 ONLY in ALL SLAVE CLOCKS TO MORE SLAVES IN THE NETWORK MULTIZONE CLOCK SYSTEM WITH ATOMIC TIME RECEIVER and using SELENA clock as the MASTER. 5
6 CLOCK SUPPLY SHOWN ALL CLOCKS AS SLAVES ( Option ) ENABLE functions Fn34 and Fn70 in ALL CLOCKS and ZONES OR TO MORE SLAVES IN THE NETWORK MULTIZONE CLOCK SYSTEM WITH ATOMIC TIME RECEIVER and using the Receiver as the MASTER. 6
SELENA Multifunctional LED CLOCK
SELENA Multifunctional LED CLOCK Rev. V32D KERA Technologies Inc. E-mail: sales@ledclocks.com INDEX PAGE Features...... 3 Installation...... 4 Power Connection... 4 IR Remote Control... 5 REMOTE CONTROL
More informationAE SERIES GPS MASTER CLOCK SYSTEMS
FN:427AMAN2.DOC AE SERIES GPS MASTER CLOCK SYSTEMS DESCRIPTION AE Series GPS Master Clock Systems are synchronized by the Global Positioning System (GPS), which is a system of satellites deployed by the
More informationInstallation instructions for Brookhouse NMEA multiplexer model AISC
Installation instructions for Brookhouse NMEA multiplexer model AISC General This addendum describes connections and features of multiplexer model AISC where they are different from the standard Brookhouse
More informationSAPLING MASTER CLOCKS
SAPLING MASTER CLOCKS Sapling SMA Master Clocks Sapling is proud to introduce its SMA Series Master Clock. The standard models come loaded with many helpful features including a user friendly built-in
More information1 OVERVIEW 2 WHAT IS THE CORRECT TIME ANYWAY? Application Note 3 Transmitting Time of Day using XDS Packets 2.1 UTC AND TIMEZONES
1 OVERVIEW This application note describes how to properly encode Time of Day information using EIA-608-B Extended Data Services (XDS) packets. In the United States, the Public Broadcasting System (PBS)
More informationC Module Description
IQMMX -Input Router & ASI Distribution Amplifier C Module Description The IQMMX is an ASI to 1 switch, distribution amplifier and transport stream switcher with up to 8 outputs in double width form or
More informationKramer Electronics, Ltd. USER MANUAL. Models: VS-162AV, 16x16 Audio-Video Matrix Switcher VS-162AVRCA, 16x16 Audio-Video Matrix Switcher
Kramer Electronics, Ltd. USER MANUAL Models: VS-162AV, 16x16 Audio-Video Matrix Switcher VS-162AVRCA, 16x16 Audio-Video Matrix Switcher Contents Contents 1 Introduction 1 2 Getting Started 1 3 Overview
More informationChapter 23 Dimmer monitoring
Chapter 23 Dimmer monitoring ETC consoles may be connected to ETC Sensor dimming systems via the ETCLink communication protocol. In this configuration, the console operates a dimmer monitoring system that
More informationKramer Electronics, Ltd. USER MANUAL. Models: VS-626, 6x6 Video / Audio Matrix Switcher VS-828, 8x8 Video / Audio Matrix Switcher
Kramer Electronics, Ltd. USER MANUAL Models: VS-626, 6x6 Video / Audio Matrix Switcher VS-828, 8x8 Video / Audio Matrix Switcher Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 1
More informationBUSES IN COMPUTER ARCHITECTURE
BUSES IN COMPUTER ARCHITECTURE The processor, main memory, and I/O devices can be interconnected by means of a common bus whose primary function is to provide a communication path for the transfer of data.
More informationSPG700 Multiformat Reference Sync Generator Release Notes
xx ZZZ SPG700 Multiformat Reference Sync Generator Release Notes This document supports firmware version 3.0. www.tek.com *P077123104* 077-1231-04 Copyright Tektronix. All rights reserved. Licensed software
More informationAI-1204Z-PCI. Features. 10MSPS, 12-bit Analog Input Board for PCI AI-1204Z-PCI 1. Ver.1.04
10MSPS, 12-bit Analog Board for PCI AI-1204Z-PCI * Specifications, color and design of the products are subject to change without notice. This product is a PCI bus-compliant interface board that expands
More informationUHF REMOTE RECEIVER INSTALLATION & PROGRAMMING
UHF REMOTE RECEIVER INSTALLATION & PROGRAMMING Table of Contents Section Page No INTRODUCTION... 3 TOOLS & TEST EQUIPMENT... 4 RECEIVER POSITION... 4 UHF REMOTE RECEIVER RELEVANT HIGH GAIN AERIALS... 4
More informationIntelligent Security and Fire Ltd
User Manual Product ranges covered by this manual Vi-P14 Vi-P14A Document Reference Date Firmware Vi-Q4C1 Viq601a.doc 26/11/2009 From Viq001a21 Videoswitch Telephone 01252-851510 Ocean House, Redfields
More informationAN-822 APPLICATION NOTE
APPLICATION NOTE One Technology Way P.O. Box 9106 Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 Fax: 781.461.3113 www.analog.com Synchronization of Multiple AD9779 Txs by Steve Reine and Gina Colangelo
More informationRF Solution for LED Display Screen
RF Solution for LED Display Screen Introduction RF is a kind of wireless telecommunication technology, now standard IEEE802.11B is much popular. Communication speed between server and terminal can reach
More informationC ch optical MADI & AoIP I/O. MASTER mode: A C8000 frame may be clocked via MADI input or AES67 network. AoIP Dante Brooklin II OEM module
features Interface for AoIP (AES67 or DANTE) Two AoIP network ports for redundant or switch operation MADI I/O connection Optical SFP module / LC connectors (multi mode or single mode fiber) BNC parallel
More informationWeschler AMT Software for the Enhanced Version Transformer Advantage
Weschler AMT Software for the Enhanced Version Transformer Advantage The Weschler AMT software is used to configure and monitor a Transformer Advantage from a PC. The AMT software also simplifies extraction
More informationIP LIVE PRODUCTION UNIT NXL-IP55
IP LIVE PRODUCTION UNIT NXL-IP55 OPERATION MANUAL 1st Edition (Revised 2) [English] Table of Contents Overview...3 Features... 3 Transmittable Signals... 3 Supported Networks... 3 System Configuration
More informationPRESET TEN ARCHITECTURAL TWO OWNERS MANUAL
PRESET TEN ARCHITECTURAL TWO OWNERS MANUAL model PRE10-A2 Doug Fleenor Design 396 Corbett Canyon Road Arroyo Grande, CA 93420 (805) 481-9599 Software Version 1.0 Manual Revision 12/2/2008 Serial # 08B001
More informationFN:4181NX_M1.DOC MC4181NX MASTER CLOCK MC4181NX
FN:4181NX_M1.DOC MC4181NX MASTER CLOCK MC4181NX TABLE OF CONTENTS 1.0 INTRODUCTION 2.0 SPECIFICATIONS 3.0 INSTALLATION 4.0 GETTING STARTED 4.1 The Auto-Prompt Display 4.2 The Cursor, Entering Data 4.3
More informationSPG700 Multiformat Reference Sync Generator Release Notes
xx ZZZ SPG700 Multiformat Reference Sync Generator Release Notes This document supports firmware version 2.1. www.tek.com *P077123100* 077-1231-00 Copyright Tektronix. All rights reserved. Licensed software
More informationORM0022 EHPC210 Universal Controller Operation Manual Revision 1. EHPC210 Universal Controller. Operation Manual
ORM0022 EHPC210 Universal Controller Operation Manual Revision 1 EHPC210 Universal Controller Operation Manual Associated Documentation... 4 Electrical Interface... 4 Power Supply... 4 Solenoid Outputs...
More informationRS232 Decoding (Option)
bit0 bit1 bit2 bit3 bit4 bit5 bit6 bit7 bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 7 Protocol Decoding RIGOL RS232 Decoding (Option) RS232 serial bus consists of the transmitting data line (TX) and the receiving
More informationSPG8000A Master Sync / Clock Reference Generator Release Notes
xx ZZZ SPG8000A Master Sync / Clock Reference Generator Release Notes This document supports firmware version 2.5. www.tek.com *P077122204* 077-1222-04 Copyright Tektronix. All rights reserved. Licensed
More informationSQTR-2M ADS-B Squitter Generator
SQTR-2M ADS-B Squitter Generator Operators Manual REVISION A B C D E F G H J K L M N P R S T U V W X Y Z December 2011 KLJ Instruments 15385 S. 169 Highway Olathe, KS 66062 www.kljinstruments.com NOTICE:
More informationUS Rev. E, Copyright 1 September 2008 CAUTION:
The Spectracom NetClock Wireless Clocks are cost-effective facilities clocks that display synchronized time across a campus, within a structure, or in a variety of other installations. A Wireless Clock
More informationFN:4181M5.DOC MC4181N SERIES MASTER CLOCKS MC4181N
FN:4181M5.DOC MC4181N SERIES MASTER CLOCKS MC4181N TABLE OF CONTENTS 1.0 INTRODUCTION 2.0 SPECIFICATIONS 3.0 INSTALLATION 4.0 GETTING STARTED 4.1 The Auto-Prompt Display 4.2 The Cursor, Entering Data 4.3
More informationModel CMX3838A2 AV Matrix Switch with DSP audio (firmware 1.0)
Model CMX3838A2 AV Matrix Switch with DSP audio (firmware 1.0) Overview: This product is a full featured video & audio matrix switch. It is most commonly used to independently distribute video & audio
More informationKramer Electronics, Ltd. USER MANUAL. Model: VS x 1 Sequential Video Audio Switcher
Kramer Electronics, Ltd. USER MANUAL Model: VS-120 20 x 1 Sequential Video Audio Switcher Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 2 3 Overview 3 4 Installing the VS-120 in
More informationSYNC I/O Guide Version 1.1
SYNC I/O Guide Version 1.1 For Pro Tools 5.3.x and Pro Tools 6.x Digidesign 2001 Junipero Serra Boulevard Daly City, CA 94014-3886 USA tel: 650 731 6300 fax: 650 731 6399 Technical Support (USA) tel: 650
More informationUsing the XSV Board Xchecker Interface
Using the XSV Board Xchecker Interface May 1, 2001 (Version 1.0) Application Note by D. Vanden Bout Summary This application note shows how to configure the XC9510 CPLD on the XSV Board to enable the programming
More informationOPERATION MANUAL INSTALLATION AND KML.F. Fiber Optic Interface Main Link. Kilomux Module. The Access Company
INSTALLATION AND OPERATION MANUAL KML.F Fiber Optic Interface Main Link Kilomux Module The Access Company KML.F Fiber Optic Interface Main Link Kilomux Module Installation and Operation Manual Notice
More informationPackage Contents. LED Protocols Supported. Safety Information. Physical Dimensions
Pixel Triton Table of Contents Package Contents... 1 Safety Information... 1 LED Protocols Supported... 1 Physical Dimensions... 1 Software Features... 2 LED Status... 2 Power... 2 Activity LED... 2 Link
More informationC8000. sync interface. External sync auto format sensing : AES, Word Clock, Video Reference
features Standard sync module for a frame Internal sync @ 44.1 / 48 / 88.2 / 96kHz External sync auto format sensing : AES, Word Clock, Video Reference Video Reference : Black Burst (NTSC or PAL) Composite
More informationPRESET 10 ARCHITECTURAL OWNERS MANUAL
PRESET 10 ARCHITECTURAL OWNERS MANUAL Doug Fleenor Design 396 Corbett Canyon Road Arroyo Grande, CA 93420 (805) 481-9599 Software Version 2.0 Manual Revision 5 February, 2006 Serial # 05C183 PRODUCT DESCRIPTION
More informationiremote ts Frequently asked questions
iremote TS and IntelliFile 3 Frequently Asked Questions iremote ts Frequently asked questions 1. Does the iremote TS support multiple home theaters? Currently, the iremote TS supports one home theater
More informationModel Colorado Ultra Wide Bandwidth HDTV Matrix Switch
HDTV Supply, Inc www.hdtvsupply.com Model Colorado Ultra Wide Bandwidth HDTV Matrix Switch Overview: This product is a full featured video & audio matrix switch. It is most commonly used to independently
More informationVNS2200 Amplifier & Controller Installation Guide
VNS2200 Amplifier & Controller Installation Guide VNS2200 Amplifier & Controller Installation 1. Determine the installation location for the VNS2200 device. Consider the following when determining the
More informationUsing the More Advanced Features of the AUTOcard-SA System
Using the More Advanced Features of the AUTOcard-SA System IMPORTANT NOTICE This manual describes the AUTOcard-SA system s more advanced features. If you wish to only program the system s basic features
More informationKramer Electronics, Ltd. USER MANUAL. Model: 900xl. Power Amplifier
Kramer Electronics, Ltd. USER MANUAL Model: 900xl Power Amplifier Introduction Contents 1 Introduction 1 2 Getting Started 1 2.1 Recycling Kramer Products 1 3 Overview 2 4 Your 900xl Power Amplifier 3
More informationSEL-3405 High-Accuracy IRIG-B Fiber-Optic Transceiver
SEL-3405 High-Accuracy IRIG-B Fiber-Optic Transceiver Accurate IRIG-B Over Fiber Optics Major Features and Benefits The SEL-3405 High-Accuracy IRIG-B Fiber-Optic Transceiver can send high-accuracy demodulated
More informationGTT LTE RRU ADD- ON USER GUIDE
GTT LTE RRU ADD- ON USER GUIDE Copyright 2015 Gefle Testteknik AB. All rights reserved. Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or mechanical,
More information3D QUALITY CONTROL SOFTWARE MPES-3DQC1 USER S GUIDE. [English] 1st Edition (Revised 1) Software Version 1.10
3D QUALITY CONTROL SOFTWARE MPES-3DQC1 USER S GUIDE [English] 1st Edition (Revised 1) Software Version 1.10 NOTICE TO USERS 2011 Sony Corporation. All rights reserved. This manual or the software described
More informationAuxiliary states devices
22 Auxiliary states devices When sampling using multiple frame states, Signal can control external devices such as stimulators in addition to switching the 1401 outputs. This is achieved by using auxiliary
More informationC8188 C8000 1/10. digital audio modular processing system. 4 Channel AES/EBU I/O. features. block diagram. 4 balanced AES inputs
features 4 balanced AES inputs Input Sample Rate Converters (SRC) 4 balanced AES outputs Relay bypass for pairs of I/Os Relay wait time after power up Master mode (clock master for the frame) 25pin Sub-D,
More informationInstruction manual Universal Fieldbus-Gateway UNIGATE IC - RS
Instruction manual niversal Fieldbus-Gateway NIGE IC - S rt.-no.: V3504E Carl-Zeiss-Str. 8 D-65520 Bad Camberg el:+49-(0)6434-9433-0 Hotline: +49-(0)6434-9433-33 Fax: +49-(0)6434-9433-40 Internet: http://www.deutschmann.de
More informationUser s Guide. Dimensions 4000 Series Control System. Topics at a Glance
User s Guide Dimensions 4000 Series Control System Topics at a Glance Installation...See Installation Guide Quick Start Configuration...11 User Interface...8 Initial Setup...19 Scheduling...63 Scene Recording...54
More informationChapter Status. Contents. Chapter 5. Overview STATUS
Chapter 5 3512 Status Contents Overview... 5-2 STATUS... 5-2 3512 e f r c (Default Display) Category... 5-4 Default Display Examples... 5-4 LINE SELECT Category... 5-5 e ALARM STATUS Category... 5-5 e
More informationWaveMaker III Gartech Enterprises Inc. 12/17/2012
WaveMaker III Gartech Enterprises Inc. 12/17/2012 1 Preface: WaveMaker III standalone unit is produced for those desiring a flexible wave form generator. This unit is capable of providing selectable waveform
More informationTechnical data. General specifications. Indicators/operating means
Model Number Single head system Features Sensor head bidirectional and rotatable Function indicators visible from all directions Quick mounting bracket Selectable sound lobe width Programmable Diagrams
More informationIndustriefunkuhren. Technical Manual. OEM Sync-Module FE1000 (IRIG-B) ENGLISH
Industriefunkuhren Technical Manual OEM Sync-Module FE1000 (IRIG-B) ENGLISH Version: 07.02-24.03.2014 2 / 19 FE1000 IRIG-B Synchronisation - V07.02 IMPORTANT NOTES Version Number (Firmware / Manual) THE
More informationKramer Electronics, Ltd. USER MANUAL. Model: VS-201YC. 2x1 s-video Switcher
Kramer Electronics, Ltd. USER MANUAL Model: VS-201YC 2x1 s-video Switcher Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 1 3 Overview 3 4 Your VS-201YC 2x1 s-video Switcher 4 5
More informationOcean Sensor Systems, Inc. Wave Staff III, OSSI With 0-5V & RS232 Output and A Self Grounding Coaxial Staff
Ocean Sensor Systems, Inc. Wave Staff III, OSSI-010-008 With 0-5V & RS232 Output and A Self Grounding Coaxial Staff General Description The OSSI-010-008 Wave Staff III is a water level sensor that combines
More informationIP LIVE PRODUCTION UNIT NXL-IP55 USO RESTRITO. OPERATION MANUAL 1st Edition (Revised 2) [English]
IP LIVE PRODUCTIO UIT XL-IP55 USO RESTRITO OPERATIO MAUAL 1st Edition (Revised 2) [English] Table of Contents Overview... 3 Features... 3 Transmittable Signals... 3 Supported etworks... 3 System Configuration
More informationMODEL 2873 Chassis with RS422 CLOCK RECOVERY Module, IOCRM4
MODEL 2873 Chassis with RS422 CLOCK RECOVERY Module, IOCRM4 FEATURES o Clock Recovery from Data Only o RS422 Nominal Input o RS422 Data and Clock outputs o Bit Rate from 1 kbps to 20 Mbps NRZ 1 kbps to
More informationTHE ASTRO LINE SERIES GEMINI 5200 INSTRUCTION MANUAL
THE ASTRO LINE SERIES GEMINI 5200 INSTRUCTION MANUAL INTRODUCTION The Gemini 5200 is another unit in a multi-purpose series of industrial control products that are field-programmable to solve multiple
More informationTRIMBLE GPS / 10MHz REFERENCE MONITOR DISPLAY V January 2015
TRIMBLE GPS / 10MHz REFERENCE MONITOR DISPLAY V1.2-1.4 January 2015 A display and command module for the Trimble Thunderbolt GPS with 10MHz reference oscillator. by Hubbatech Software Revision Notes: 1.2-2014
More informationIntroduction to Serial I/O
CS/ECE 6780/5780 Al Davis Serial I/O Today s topics: general concepts in preparation for Lab 8 1 CS 5780 Introduction to Serial I/O 2 CS 5780 Page 1 A Serial Channel 3 CS 5780 Definitions 4 CS 5780 Page
More informationPage 1. Introduction to Serial I/O. Definitions. A Serial Channel CS/ECE 6780/5780. Al Davis. Today s topics: Serial I/O
Introduction to Serial I/O CS/ECE 6780/5780 Al Davis Serial I/O Today s topics: general concepts in preparation for Lab 8 1 CS 5780 2 CS 5780 A Serial Channel Definitions 3 CS 5780 4 CS 5780 Page 1 Bandwidth
More informationCELLO SETUP WITH WinGPS CelloSetup_WinGPS(15.9).doc September 17, Contents
F. S. BRAINARD & COMPANY PO Box 366, 5 Terri Lane Unit 15, Burlington, NJ 08016 tel: (609) 387-4300 fax: (609) 387-4304 www.meter-master.com email: cellosupport@meter-master.com CELLO SETUP WITH WinGPS
More informationHigh Speed Async to Sync Interface Converter
DECEMBER 1995 IC558A High Speed Async to Sync Interface Converter High Speed Async To Sync Interface Converter CUSTOMER SUPPORT INFORMATION Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight
More informationVorne Industries. 87/719 Analog Input Module User's Manual Industrial Drive Itasca, IL (630) Telefax (630)
Vorne Industries 87/719 Analog Input Module User's Manual 1445 Industrial Drive Itasca, IL 60143-1849 (630) 875-3600 Telefax (630) 875-3609 . 3 Chapter 1 Introduction... 1.1 Accessing Wiring Connections
More informationStatement SmartLCT User s Manual Welcome to use the product from Xi an NovaStar Tech Co., Ltd. (hereinafter referred to as NovaStar ). It is our great
LED Display Configuration Software SmartLCT User s Manual Software Version: V3.0 Rev3.0.0 NS110100239 Statement SmartLCT User s Manual Welcome to use the product from Xi an NovaStar Tech Co., Ltd. (hereinafter
More informationSTR 2000 Series Transceiver Programming Manual (V2) Table of Contents
Note: Press both buttons together simultaneously to enter programming mode. PROGRAMMING THE DATE Table of Contents Programming the Date.. Page 2 TECHNICAL MODE Technical Mode..... Pages 2-3 PROGRAMMABLE
More informationREMOTE DISPLAY WIRELESS DECODER MK II
REMOTE DISPLAY WIRELESS DECODER MK II INSTALLATION MANUAL Part No. LED-DEC 1. Contents 1. Contents... 1 2. Equipment List... 2 3. Overview... 2 Introduction... 2 Location Selection **Important **... 2
More informationMaster Time Clock MTC Users Manual
Master Time Clock MTC-6000 Users Manual Midwest Time Control Phone (972)987-4408 Toll Free (888)713-0373 FAX (877)720-9291 www.midwest-time.com sales@midwest-time.com TABLE OF CONTENTS TOPIC PAGE GENERAL
More informationACT 10 Digital Keypad Operating & Installation Instructions This manual is found at
ACT 10 Digital Keypad Operating & Installation Instructions 18-00001 This manual is found at www.eaglesecuritysolutions.co.uk Installation Notes Always remember to factory default the controller before
More informationInstallation Instructions
Bell Ringer OVERVIEW Thank you for choosing a TimeTrax Sync 5300 Bell Ringer. The TimeTrax Sync 5300 directs bells and horns (sold separately) to promote accountability, productivity and punctuality with
More informationInstallation Checklist
Installation Checklist NavNet TZtouch2 Installation Checklist NavNet TZtouch2 Network Installation Connect all TZtouch2 MFDs to the Ethernet Network. If a HUB101 is used, set the internal HUB DIP switches
More informationNixie Clock Type Nixie Maestro
Assembly Instructions and User Guide Nixie Clock Type Nixie Maestro - 1 - Issue Number Date REVISION HISTORY Reason for Issue 4 01 April 2017 New version with neons for AM / PM 3 10 December 2014 Typing
More informationIndustriefunkuhren. Technical Manual. IRIG-B Generator-Module for analogue / digital Signals of Type: IRIG-B / IEEE C / AFNOR NF S87-500
Industriefunkuhren Technical Manual IRIG-B Generator-Module for analogue / digital Signals of Type: IRIG-B / IEEE C37.118 / AFNOR NF S87-500 Module 7628 ENGLISH Version: 02.01-06.03.2013 2 / 20 7628 IRIG-B
More informationManaging a Time Clock Station
Managing a Time Clock Station The time clock stations manage web-enabled time clock stations. Browse System Setup under Operations in the left navigation bar. Click Time Clock Stations see a list of the
More informationArtistic Licence Engineering Ltd Firmware Version V3.03 Manual Revision V1-9
Light-Switch & Switch-Edit Artistic Licence Engineering Ltd Firmware Version V3.03 Manual Revision V1-9 Artistic Licence Engineering Ltd. Switch-Edit Manual 2/47 Artistic Licence Engineering Ltd. Switch-Edit
More informationMultiView T4 / T5 Transmitter
MultiView T4 / T5 Transmitter Quick Reference & Setup Guide Magenta Research 128 Litchfield Road, New Milford, CT 06776 USA (860) 210-0546 FAX (860) 210-1758 www.magenta-research.com PN 5310188-01, Rev
More informationRadio Systems, Inc. CT-2002 Clock/Timer Manual
CT-2002 Clock/Timer Manual For Models: CT-2002 Desktop CT-2002 Thin CT-2002 Large 2 CT-2002 Large 4 CT-2002 Console CT-2002 Desktop GPS CT-2002 2 GPS CT-SYNC Clock to PC Synchronization Kit GPS-SYNC GPS
More informationCat5 DVI-D Extender. User s Guide Avenview Inc. All rights reserved.
Cat5 DVI-D Extender User s Guide 2007 Avenview Inc. All rights reserved. The contents of this document are provided in connection with Avenview Inc. ( Avenview ) products. Avenview makes no representations
More informationB. The specified product shall be manufactured by a firm whose quality system is in compliance with the I.S./ISO 9001/EN 29001, QUALITY SYSTEM.
VideoJet 8000 8-Channel, MPEG-2 Encoder ARCHITECTURAL AND ENGINEERING SPECIFICATION Section 282313 Closed Circuit Video Surveillance Systems PART 2 PRODUCTS 2.01 MANUFACTURER A. Bosch Security Systems
More informationModel 4455 ASI Serial Digital Protection Switch Data Pack
Model 4455 ASI Serial Digital Protection Switch Data Pack Revision 1.5 SW v2.2.11 This data pack provides detailed installation, configuration and operation information for the 4455 ASI Serial Digital
More informationEEG A1452 SCTE-104 Inserter Frame Card
EEG A1452 SCTE-104 Inserter Frame Card Product Manual EEG Enterprises, Inc. 586 Main Street Farmingdale, New York 11735 TEL: (516) 293-7472 FAX: (516) 293-7417 Copyright EEG Enterprises, Inc. 2017 All
More informationConfiguration guide TDH 800 PAL output module. TDH 800 PAL output module Version A EN triax.com
Configuration guide TDH 800 PAL output module Model Item no. TDH 800 PAL output module 692850 692851 Version 891575A 08-2013 EN triax.com Contents Contents Introduction... 3 System requirements... 3 Computer
More informationR5 RIC Quickstart R5 RIC. R5 RIC Quickstart. Saab TransponderTech AB. Appendices. Project designation. Document title. Page 1 (25)
Appendices 1 (25) Project designation R5 RIC Document title CONTENTS 2 (25) 1 References... 4 2 Dimensions... 5 3 Connectors... 6 3.1 Power input... 6 3.2 Video I... 6 3.3 Video Q... 6 3.4 Sync... 6 3.5
More informationOcean Sensor Systems, Inc. Wave Staff, OSSI F, Water Level Sensor With 0-5V, RS232 & Alarm Outputs, 1 to 20 Meter Staff
Ocean Sensor Systems, Inc. Wave Staff, OSSI-010-002F, Water Level Sensor With 0-5V, RS232 & Alarm Outputs, 1 to 20 Meter Staff General Description The OSSI-010-002E Wave Staff is a water level sensor that
More informationK-BUS Dimmer Module User manual-ver. 1
K-BUS Dimmer Module User manual-ver. 1 KA/D0103.1 KA/D0203.1 KA/D0403.1 Content 1. Introduction... 3 2. Technical Parameter... 3 3. Dimension and Connection Diagram... 4 3.1 KA/D0103.1... 4 3.2 KA/D0203.1...
More informationTechnical Description. Large Scale Display 4985
Technical Description Large Scale Display 4985 Version 05.00 01.06.2004 COMPANY INFO Safety information The safety regulations and technical data are important for the smooth running of the devices and
More informationMICROSYNC. User Manual. Microgate s.r.l. Via Stradivari, 4 Stradivaristr BOLZANO - BOZEN ITALY
MICROSYNC User Manual Microgate s.r.l. Via Stradivari, 4 Stradivaristr. 39100 BOLZANO - BOZEN ITALY Pagina 2 di 20 Contents 1. INTRODUCTION... 3 2. DESCRIPTION... 4 3. SWITCHING ON/OFF... 5 4. BASIC USE...
More informationPg. 2 4: NavNet TZtouch MFD Network Installation (w/o: NN3D) Pg. 5: MIXED NavNet TZtouch MFD and NavNet 3D MFD Network Installation Pg.
Pg. 2 4: NavNet TZtouch MFD Network Installation (w/o: NN3D) Pg. 5: MIXED NavNet TZtouch MFD and NavNet 3D MFD Network Installation Pg. 6: DFF1 Dip Switch Settings Pg. 7: DFF3 Dip Switch Settings Pg. 8:
More informationSCART COMMANDER. Channels 2 audio channels 4 video channels 2 digital channels 2 control channels (pin 8 & 16)
SCART COMMANDER PRODUCT OVERVIEW The Keene Scart Switch Box is a high quality audio/video switcher designed to allow the connection of multiple sources to one display. Particular attention has been given
More informationTechnical data. General specifications. 60 ma Power consumption P 0. 1 W Time delay before availability t v. 120 ms Interface. Protocol IO-Link V1.
Model Number Single head system Features IO-link interface for service and process data Programmable via DTM with PACTWARE programmable switch outputs Selectable sound lobe width Synchronization options
More informationController, Scheduler-Timer Model UCS-01. User Guide
Model UCS-01 User Guide QUICK REFERENCE GUIDE Time Date IDLE SCREEN 03:50PM [RUN] 05/09/06 Tue Day of the Week Schedule Mode (change via 'Set Time') [OFF] = No Events Operate [RUN] = Run 'R' Events Operate
More informationPRESET TEN ARCHITECTURAL TWO OWNERS MANUAL
PRESET TEN ARCHITECTURAL TWO OWNERS MANUAL model PRE10-A2 Doug Fleenor Design 396 Corbett Canyon Road Arroyo Grande, CA 93420 (805) 481-9599 Software Version 1.8 Manual Revision 1/10/2017 Serial # 099000
More informationTeletext Inserter Firmware. User s Manual. Contents
Teletext Inserter Firmware User s Manual Contents 0 Definition 3 1 Frontpanel 3 1.1 Status Screen.............. 3 1.2 Configuration Menu........... 4 2 Controlling the Teletext Inserter via RS232 4 2.1
More informationAPPLICATION NOTE # Monitoring DTMF Digits Transmitted by a Phone
APPLICATION NOTE # Product: 930A Communications Test Set 930i Communications Test Set Monitoring DTMF Digits Transmitted by a Phone Introduction This Application Note describes how to configure and connect
More informationCLV-401A CAMERA LINK VIDEO SPLITTER. User s Manual. Document # , Rev 1.1, 4/2/2018
CLV-401A CAMERA LINK VIDEO SPLITTER User s Manual Document # 201058, Rev 1.1, 4/2/2018 Vivid Engineering 415 Boston Turnpike, Suite 305 Shrewsbury, MA 01545 Phone 508.842.0165 Fax 508.842.8930 www.vividengineering.com
More informationKramer Electronics, Ltd. USER MANUAL. Model: FC Analog Video to SDI Converter
Kramer Electronics, Ltd. USER MANUAL Model: FC-7501 Analog Video to SDI Converter Contents Contents 1 Introduction 1 2 Getting Started 1 3 Overview 2 4 Your Analog Video to SDI Converter 3 5 Using Your
More informationFTS84/85 Feature Application Field. Temperature & Humidity / Flow Measuring Specialist. Monitor gas and flow for industrial process
FTS84/8 Feature Application Field Capable of temperature compensation and linear adjustment Double line character : air velocity & temperature Switch for physical quantity:[m/s] [ft/s] [km/h] [mph] [knot]
More informationTroubleshooting. 1. Symptom: Status indicator (Red LED) on SSR is constant on. 2. Symptom: Output indicator (Yellow LED) on SSR is flashing.
Product Data Electrical Data SST (Transmitter) SSR (Receiver) Supply voltage 18 30 V dc Max. Voltage ripple 15 % (within supply range) Current consumption 100 ma (RMS) 75 ma Digital - 100 ma Max. outputs
More informationDXI SAC Software: Configuring a CCTV Switcher. Table of Contents
APPLICATION NOTE MicroComm DXI DXI SAC Software: Configuring a CCTV Switcher Table of Contents 1. Intent & Scope... 2 2. Introduction... 2 3. Options and Parameters... 2 3.1 When to switch the CCTV...2
More informationLaboratory Exercise 4
Laboratory Exercise 4 Polling and Interrupts The purpose of this exercise is to learn how to send and receive data to/from I/O devices. There are two methods used to indicate whether or not data can be
More informationLAN Network Tester. Operating Manual. Part No TRIAX - your ultimate connection
LAN Network Tester Part No. 157011 Operating Manual TRIAX - your ultimate connection Safety and Disposal The LAN Network Tester operates off 6V DC only. Only use the internal, battery powered, 6V power
More information