Lighting Zone Controller. Specifications

Size: px

Start display at page:

Download "Lighting Zone Controller. Specifications"

Alexandrina Collins
6 years ago
Views:

Lighting Zone ler Lighting Zone ler dmw-lzc1-1 02.22.

It works as part of a total system by communicating with a Digital microwatt router panel and server or GAFIK 7000P processor.

1 Lighting Zone ler Lighting Zone ler dmw-lzc The lighting zone controller (LZC) intelligently manages lighting loads to minimize consumption based on input from wall controls, occupant sensors, and/or daylight sensors. It works as part of a total system by communicating with a Digital microwatt router panel and server or GAFIK 7000P processor. Each lighting zone controller includes an integrated current transformer to measure load consumption. LZC1 with cover closed The Lighting Zone ler (LZC) works with: Digital microwatt lighting automation systems GAFIK 7000 centralized lighting control systems Lutron fluorescent dimming ballasts Specifications Power Input : V, 50/60 Hz s a full 20 A circuit (16 A of continuous load) Model is UL, CSA, and/or NOM listed LZC1 with cover open SPECIFICATI SUBMITTAL

2 Lighting Zone ler Specifications (continued) Features Provides direct control of a single 16 A circuit of Lutron Hi-Lume and ECO-10 3-wire fluorescent dimming ballasts Capable of switching 16 A of high in-rush lighting load such as magnetic fluorescent ballast, electronic fluorescent ballast, incandescent, magnetic lowvoltage, electronic low-voltage and HID loads Capable of switching motor loads up to 1/3 120 V and 1/2 277 V Contains Lutron s patented SoftswitchTM technology, which prevents arcing that is typically associated with high in-rush loads Supports single or multi-location wall controls for dimming and switching zones Accepts inputs from most 15- and 24-volt occupant sensors; can supply up to 60 ma to occupant sensors (40 ma at 100 V, 50 Hz input) Can control light level due to variations in ambient light using a Lutron daylight sensor Provides an automatic 100-hour burn-in function to assist in the seasoning of new fluorescent lamps Includes an emergency contact closure to force lights on to a preset level Can be daisy-chained to provide a maximum of 63 lighting zone controllers per LZC link Wires to the LZC link of a Digital microwatt router panel (DMW-P3) or the LZC link of a GAFIK 7000P processor dmw-lzc The following features require a connection with a Digital microwatt or GAFIK 7000 system: Set minimum and maximum light levels Set unoccupied light level Set daylight sensor gain Start, stop, pause, or resume 100-hour burn-in mode Set occupant sensor timeout length Enable/disable and monitor daylight sensors, occupant sensors, and/or wall controls Measure and energy usage Set unit s current mode (see below) Unit Modes Normal Working Hours: This mode is active when no other mode is active. In this mode the unit uses wall controls, daylight sensors, and occupancy sensors to determine the actual light level. These inputs are combined in order to save the maximum amount of energy. Emergency: In emergency mode the lights will go to the emergency light level and will not respond to any other control input. Emergency mode may be entered by opening the hardware emergency contact closure input at the router panel (in a Digital microwatt system), via the circuit selector SENSE connection (in a GAFIK 7000 system), or via software. See the Specification Submittal for the GAFIK 7000P processor and/or the Digital microwatt router panel for additional wiring details. Flash: Flash mode changes the actual light level from the high end to the low end every 4 seconds. It is used for locating or troubleshooting a unit. SPECIFICATI SUBMITTAL

3 Lighting Zone ler dmw-lzc Specifications (continued) Afterhours: In afterhours mode, the units will wait a user-configurable period of time (warning time). After the warning time, the lights will flash a userconfigurable number of times. Then, the lights will dim to low end for a user-settable period of time (off delay). Finally, the lights will turn off. The lights will go on and the cycle will repeat if the space becomes occupied or the light level is changed via the wall control or via the software. Burn-In: Burn-in mode sets the lights to the maximum level for a period of 100 hours, after which burn-in mode will automatically end. During this time the lights can only be turned on and off via wall control, timeclock, or through the software. Burn-in mode can be manually started, paused, resumed, or stopped. This mode should be run any time new dimmable fluorescent lamps are installed. Non-Dim: This mode activates features for units that cannot be dimmed. These features are: during flash mode, lights will turn on and off; when daylight sensor cutback reaches 25%, the lights will turn off; and if load shed is greater than zero, the lights will turn off. This mode can be used in conjunction with any other mode. Address Switch Orientation of switches indicates the lighting zone controller address The largest acceptable address is 63 Switchable Load Types Incandescent (tungsten/halogen) (16 A maximum per circuit) Magnetic low-voltage transformer (16 A maximum per circuit) Electronic low-voltage transformer (16 A maximum per circuit) Neon/cold cathode (16 A maximum per circuit) Magnetic and electronic fluorescent ballasts (16 A maximum per circuit) HID (16 A maximum per circuit) Motor loads (1/3 120 V, 1/2 277 V maximum per circuit) Dimmable Load Types Lutron 3-wire phase controlled fluorescent dimming ballasts Dimmable Load Types equiring an Interface (120 V applications only) Lutron Tu-Wire fluorescent dimming ballasts Incandescent (tungsten/halogen) Magnetic low-voltage transformer Electronic low-voltage transformer Neon/cold cathode Environment Temperature: F (0-40 C) elative humidity: < 90% non-condensing For indoor use only SPECIFICATI SUBMITTAL

4 LUT. D Lighting Zone ler Mounting Mount the onto a 4 x 4 in. (102 x 102 mm) standard (1900) junction box (not included, but available; Lutron part number ) Mount the unit indoors with ambient temperature between 32 F and 104 F (0 C and 40 C) and humidity <90% (non-condensing) Mount on a vertical or horizontal surface (i.e., ceiling); all wire connections will be made in the junction box; all PELV (Class 2: USA) wire connections must be made within the front cover of the unit It is recommended to mount the unit above the ceiling at the entrance of the room. This will simplify locating the unit for future maintenance Dimensions Dimensions are in inches (mm) 7.8 (150) dmw-lzc (130) 2.5 (64) Junction box CEILING W A L L Junction box Junction box 7/8 (2.2 mm) knockout for PELV (Class 2: USA) wiring input (2) mon Coopersburg, PA USA (Lighting Zone ler) (Lighting Zone er) LUT Coopersburg, PA LUT Coopersburg, PA POWE INDICATO STATUS INDICATO ADDESS operating Off: Unit is not ed or Third blink: Unit is communicating guide for addressing not operating + 24 V mon mon W WC C Common Common + 24 V + 15 V mon CLASS 2 LOW VOL TAGE WIING mon POWE INDICA TO STATUS INDICA TO ADDESS operating Off: Unit is not ed or Third blink: Unit is communicating guide for addressing not operating Lighting Zone ler ador de zona de luz Contrôleur de zone d'éclairage For installation, refer to Para la instalación, Pour installation, référer au the Digital microwatt consulte la Guía del guide pour quincaillerie Hardware Installer's Instalador de Digital Digital microwatt Guide (p/n ). microwatt Hardware (p/n ) de (p/n ). l'installateur. USA, Canada Mexico TEL FAX Enlace Digital Lien Digital EMEG Signal P/N ev. C P/N ev P/N ev. F V 50/60 Hz EMEG Address switch Front cover (shown open) SPECIFICATI SUBMITTAL

POWE INDICA TO On: Caution unit has STATUS INDICA CLASS 2 LOW VOL TAGE WIING TO P/N 500-9066 ev.

5 POWE INDICA TO On: Caution unit has STATUS INDICA CLASS 2 LOW VOL TAGE WIING TO P/N ev. D LUT Line Voltage Wiring: Lutron 3-Wire Dimming Ballasts Connect the input feed wires and the output load wires to the lighting zone controller as indicated in the wiring diagrams below. Lighting Zone ler dmw-lzc (Lighting Zone er) POWE INDICA TO STATUS INDICA TO ADDESS operating Off: Unit is not ed or Third blink: Unit is communicating guide for addressing not operating LUT Coopersburg, PA P/N ev. D CLASS 2 LOW VOL TAGE WIING EMEG + 24 V Coopersburg, PA USA Lighting Zone ler ador de zona de luz Contrôleur de zone d'éclairage For installation, refer to Para la instalación, Pour installation, référer au the Digital microwatt consulte la Guía del guide pour quincaillerie Hardware Installer's Instalador de Digital Digital microwatt Guide (p/n ). microwatt Hardware (p/n ) de (p/n ). l'installateur. USA, Canada Mexico mon mon W C Common + 24 V TEL FAX + 15 V mon Enlace Digital Lien Digital mon EMEG Signal P/N ev. F V 50/60 Hz Colors indicated refer to the lighting zone controller and ballast wire colors Green Green (ground) Distribution panel White Black White (neutral) ed (switched hot) Orange (dimmed hot) Green White Black Orange Fixture ground Lutron 3-wire phase control dimming ballast Ground (Lighting Zone ler) LUT Coopersburg, PA Neutral Hot Off: Unit is not ed or is not functioning ADDESS Continuous double blink: Unit is SWITCH operating Third blink: Unit is communicating guide for addressing with command center not operating Green Fixture ground EMEG White Black Orange Lutron 3-wire phase control dimming ballast To additional dimming ballasts SPECIFICATI SUBMITTAL

POWE INDICA TO On: Caution unit has STATUS INDICA CLASS 2 LOW VOL TAGE WIING TO P/N 500-9066 ev. D Lighting Zone ler dmw-lzc1-6 13.16.

6 POWE INDICA TO On: Caution unit has STATUS INDICA CLASS 2 LOW VOL TAGE WIING TO P/N ev. D Lighting Zone ler dmw-lzc Line Voltage Wiring: Switched Loads Connect the input feed wires and the output load wires to the lighting zone controller as indicated in the wiring diagrams below. Colors indicated refer to the lighting zone controller wire colors Green Green (ground) Distribution panel White Black White (neutral) ed (switched hot) Orange (cap off) Green White Black Switched load Ground Neutral Hot (Lighting Zone ler) LUT Coopersburg, PA Off: Unit is not ed or is not functioning ADDESS Continuous double blink: Unit is SWITCH operating Third blink: Unit is communicating guide for addressing with command center not operating EMEG Switchable load types: Incandescent (16 A) Fluorescent (16 A) Motor loads (1/3 120 V ; 1/2 277 V ) Magnetic low-voltage (16 A) Note: For switchable loads (non-dimming), make sure address switch 8 is in the position. Electronic low-voltage (16 A) Neon/cold cathode (16 A) HID (16 A) SPECIFICATI SUBMITTAL

7 CLASS 2 LOW VOL TAGE WIING P/N ev. D CLASS 2 LOW VOL TAGE WIING P/N ev. D Lighting Zone ler Low-Voltage PELV (Class 2: USA) Wiring: LZC Link Connect the PELV (Class 2: USA) lighting zone controller link (LZC link) wires to the lighting zone controller as indicated in the wiring diagram below. The lighting zone controller link wiring must be daisy-chained from one controller to another. Do not create T-taps longer than 6 inches (150 mm). dmw-lzc (Lighting Zone ler) LUT Coopersburg, PA (Lighting Zone ler) LUT Coopersburg, PA POWE INDICA TO STATUS INDICA TO ADDESS operating Off: Unit is not ed or Third blink: Unit is communicating guide for addressing not operating POWE INDICA TO STATUS INDICA TO ADDESS operating Off: Unit is not ed or Third blink: Unit is communicating guide for addressing not operating Lutron GX-CBL-46L series cable EMEG EMEG Pigtail wiring configuration: Pigtails must be less than 6 inches (150 mm) from wire connector to terminal block #22 AWG (0.64 mm 2 ) #22 AWG (0.64 mm 2 ) #12 AWG (2.5 mm 2 ) #12 AWG (2.5 mm 2 ) #24 AWG (0.5 mm 2 ) (white) (purple) Link common (black) Emergency (red) (bare) LZC link from Digital microwatt router panel, GAFIK 7000 processor, or another LZC To additional lighting zone controllers (up to 63 per link) SPECIFICATI SUBMITTAL

8 CLASS 2 LOW VOL TAGE WIING P/N ev. D Lighting Zone ler dmw-lzc Low-Voltage PELV (Class 2: USA) Wiring: s and s Connect the PELV (Class 2: USA) wall controls and sensors as indicated in the wiring diagram below s and sensors can be located up to 250 feet (76 m) from lighting zone controllers, and are wired with #18 AWG (1.0 mm 2 ) cable (Lighting Zone ler) LUT Coopersburg, PA POWE INDICA TO STATUS INDICA TO ADDESS operating Off: Unit is not ed or Third blink: Unit is communicating guide for addressing not operating EMEG } OCC COM OCC SIG sensor +15 V O +24 V } +24 V WC SIGNAL control WC COM PS COM } PS SIG sensor +24 V s Supports a maximum of three Lutron occupant sensors; additional occupant sensors can be added by using a PP-20 pack (contact Lutron for details) A maximum of three lighting zone controllers can be controlled together by the same occupant sensor(s) Supports most third-party 24 V and 15 V occupant sensors, up to 60 ma (40 ma at 100 V, 50 Hz input) s Supports a maximum of one MW-V or MW-VETS with a maximum of nine VETS-P controls, O Supports a maximum of three X-MIC-MW controls A maximum of three lighting zone controllers can be controlled together by the same wall control(s) s Only one daylight sensor may be connected to a single lighting zone controller A single daylight sensor cannot be connected to more than one lighting zone controller SPECIFICATI SUBMITTAL

9 Lighting Zone ler dmw-lzc System Wiring Diagram control and sensor PELV (Class 2: USA) wiring: (3) #18 AWG (1.0 mm 2 ) control Up to 63 lighting zone controllers per link LZC link PELV (Class 2: USA) wiring: Lutron GX-CBL-46Lseries cable 250 ft. (76 m) maximum Digital microwatt router panel or GAFIK 7000P processor Lighting zone controller Lighting zone controller 2000 ft. (610 m) maximum To additional lighting zone controllers or lighting zone controller panels Lighting zone controller Line voltage wiring: (3) #12 AWG (4.0 or 2.5 mm 2 ) plus ground 750 ft. (230 m) maximum Ballast To additional router panels and Digital microwatt (DMW) servers O to elumen manager Maximum 21 Digital microwatt router panels per Digital microwatt server; Maximum 32 GAFIK 7000P processors per elumen manager See the Specification Submittal for the GAFIK 7000P processor and/or the Digital microwatt router panel for system wiring details. Maximum Wire Lengths From To Length outer panel or 7000P processor Last LZC panel on LZC link 2000 ft. (610 m) DMW server Last router panel on link 2000 ft. (610 m) LZC panel control/occupant sensor/daylight sensor 250 ft. (76 m) LZC panel Last dimming ballast on circuit 750 ft. (230 m) SPECIFICATI SUBMITTAL

10 Lighting Zone ler dmw-lzc Address Switch Setting Chart Address each lighting zone controller in the link as detailed below. For switching only (non-dimming) controllers, switch 8 must be in the position. Photocopy one page for each link. All switches in the OFF position takes the LZC offline. outer No. Link No. Area Name Switch is up () Switch is down (OFF) Unit Address 1 Switch Setting Unit Switch Setting Unit Switch Setting Unit Switch Setting Address Address Address Note: Lighting zone controllers are typically described in system drawings and documentation using their router panel or GAFIK 7000P processor address, followed by their unit address. For example, 5A7 represents a lighting zone controller on router panel or GAFIK 7000P processor 5, link A, unit address 7. SPECIFICATI SUBMITTAL

with EcoSystem Please Read

with EcoSystem Please Read with EcoSystem Please ead Installation and Operation Guide The GAFIK Eye QS with EcoSystem control unit allows for control of both lights and shades, without interfaces, using a single control unit. Features