ARM Recommendations. Recommended Value Open Office: Comments

Transcription

1 ARM Recommendations Transmit Power Channels Open Office: 5 GHz: Min 12/Max GHz: Min 6/Max A and G radio: Min 9 / Max 127 Walled office or Classroom: 5 GHz: Min 15/Max GHz: Min 6 /Max 9 80 MHz channels ISM,U-NII-1,andU- NII MHz channels can be used in green field deployments. U-NII-2andU-NII-2e (DFS) channels must be used when operating on 80 MHz channels. Remove channel 144 from list. The difference between minimum and maximum Tx power on the same radio should not be more than 6dbm. Tx power of 5GHz radio should be 6dbm higher than 2.4 GHz radio. DFS channels if you are not close to an airport or military installation. Enabling DFS channels could create coverage holes for clients who do not support it. Most of the clients do not scan DFS channels initially, this makes roaming more inconsistent when using these channels. Ideal Coverage Index Free Channel Index Back Off Timer (sec) sec Consider using 40 MHz or 20 Mhz channels for better channel separation. 40 (only for 2.4 GHz) 1800 sec Very few clients support channel Mhz or 40MHz channel width will help in reducing channel utilization in high density open air environment. In high density environments, prevents APs from settling on high Tx power. Moves APs to a new channel if the new channel has free channel index 40 or better. Reduces the chances of frequent changes in channel and Tx power of an

2 AP. Reduces frequent Error rate threshold% channel changes in noisy environments. Error rate wait time (sec) Reduces frequent channel changes in noisy environments. Recommendations Sticky Client SNR (db) Load Balancing Client Threshold Band steering g- max- signal Restriction Timeout (sec) Up to : 25 db 18 db onwards: 18 db Up to : 10 clients 30 clients onwards: 30 clients -45 dbm -10 dbm 10 sec 3 sec 18 db SNR is ideal to initiate sticky move for most of the clients. Avoids excessive load balancing events in HD environment. Prevents users from getting stuck on 2.4G Hz in HD environment. In a production environment, reducing restriction timer to 3 seconds ensures that even during a failed steering event, the client can quickly reconnect to the network. Recommendations to Optimize Broadcast and Multicast Traffic Convert Broadcast ARP Requests to Unicast Helps convert broadcast ARP and DHCP packets to unicast.

3 Drop Broadcast and Multicast AirGroup if MDNS, DLNA, or other zero-config services are needed. Prevents all broadcast and mul- ticast traffic from flooding into AP tunnels. "Convert broadcast ARP to unicast must be Allows applications such as Air- play and ChromeCast even if drop broadcast and multicast is Recommendations to Optimize Broadcast and Multicast Traffic Multicast Streaming: DynamicMulticast Optimization (DMO) if multicast streaming is needed. SetDMOclientthreshold to 80. Converts multicast frames to unicast to deliver at higher rates. IGMP snooping or proxy needs to be enabled for DMO to work. MulticastRate Optimization Prioritizemulticaststream using controller uplink ACL. Sends multicast frames at highest possible common rate. even if DMO is Airtime Fairness Recommendations Airtime Provides equal airtime to all the Access Fair Access Fairness clients. Roaming Optimization Recommendations Data rates (Mbps) a: Basic rates: 6,12,24 Transmit Rates: 6,9,12,18,24,36,48, a & g: Basic rates: 12, a & g transmit rates: 12,24,36,48,56 May affect client performance depending on AP density and client type. Contact Aruba SE or TAC before adjusting the values.

4 Beacon Rate (Mbps) Local Prob Req Threshold (db) g: Basic rates: 1,2 Transmit Rates: 1,2,5,6,9,11,12,18,24, 36,48,54 By default lowest configured basic rate. 0 0 Fast Roaming Recommendations Opportunistic Key Caching (OKC) Validate PMKID EAPOL Rate Optimization r k v Fast BSS Transition d For both a and g radio use 12 or 24. withbeacon report set to Active Channel Report. Quiet Information Element parameter from the Radio Resource Management profile. When k is enabled, v Fast BSS Trans- ition also gets If you have gaming devices connecting to the network, then add data rate 5, 6, 9, and 11 Mbps to the G radio basic and transmit rates. Sends out beacon at rate configured and not at the default lowest basic rate. AP stops responding to client probe request if SNR is less than 15 db. Avoids full dot1x key exchange dur- ing roaming by caching the oppor- tunistic key. NOTE: Mac OS and ios devices do not support OKC. Matches PMKID sent by client with the PMKID stored in the Aruba con- troller before using OKC. Sends EAP packets at lowest con- figured transmit rate. this feature only after testing it in the lab with different types of devices connecting to the network. Helps clients make a quicker decision to roam. Helps clients to roam faster. Voice Devices Recommendations Voice devices do not scan many U-NII-2 and U- d. channels. NII-2e disabled. Channels this channel if the Some VOIP handsets do not support Channel 165 VOIP client doesn t support it. channel 165. Check the device manual for support details.

5 WMM d this feature if the device is WMM- capable. Set required DSCP values for different types of traffic. Transmission Power s Open Office A Radio Min Tx Power 12 dbm A Radio Max Tx Power 15 dbm G Radio Min Tx Power 6 dbm G Radio Max Tx Power 9 dbm Walled Office 15 dbm 18 dbm 6 dbm 9 dbm Configurations Settings Sticky Client Check SNR (db) Load Balancing Client Threshold Bandsteering g- max signal restriction timeout (sec) s s From internal testing and field experience, SNR value of 18 db has been identified as the best value before initiating sticky move for a wide variety of clients. Increasing the value of this parameter from 10 clients to 30 clients, avoids too many load balancing events in a pro- duction environment. By increasing the value of this parameter to -10 dbm, ensures that will try to band steer most of the clients from g-radio to a-radio. To steer client to the designated radio, all other radios except the designated one, blacklists the client for the time configured here. In a production environment, reducing restriction timer to 3 sec ensures that even during failed steering event client can quickly reconnect to the network.