Replacing the Tubes
|
|
- Darcy Neal
- 6 years ago
- Views:
Transcription
1 Replacing the Tubes The Tubes can be replaced for every color. The following procedure shows the example of replacing the Tube for Cyan. The procedure is the same for other colors. (1) Make sure is not in middle of any operation. (2) Press the OK Button on the Control Panel to display the Menu Display. (3) Press the Up/Down Button to select Maintenance, and then press the OK Button. Up Button OK Button Down Button (4) Press the Up/Down Button to select Head Replacement, and then press the OK Button. (5) Press the Up/Down Button to select the color for the Tube to be replaced, and then press the OK Button. The message Replace [X] Ink Cartridge & Press OK. appears: (6) Remove the Ink Cartridge of the target color, and then press the OK Button. Ink Cartridge The message Set Filter Cartridge & Press OK appears. 122
2 (7) Insert the Filter Cartridge to the Ink Cartridge Slot, and then press the OK Button. Filter Cartridge The ink-draining begins. Wait until the message Turn Off & Please Change [X] Head appears. (8) Turn off. (9) Remove the Front Cover, Back Cover, Rear Cover and Ink Cartridge Cover U. (See 7-1. Removing the Covers for details.) You can find the Print Heads on the left. Make sure that the Print Head and Tube for Cyan are drained. Print Head and Tube for Cyan (10) Remove the three screws from the Tube Holder Upper behind the Carriage. Round Tube Holder Tube Holder Upper Tube Holder Lower 123
3 (11) Remove the Round Tube Holder from the Tube. Round Tube Holder (12) Rotate the Tube Connector 90 degrees, and then disconnect the Tube. Tube Connector (13) Remove the Tube Connector from the Tube. 124
4 (14) Pull out the Tube Guard from the Tube. Tube Guard (15) Rotate and remove the Tube Clamp on the Needle side, and then disconnect the Tube. Tube Clamp (16) Remove the Tube Clamp from the Tube. 125
5 (17) Cut the Band (product name: Band, 1M) binding the Tubes. Band (18) Remove the Tube. <Note> Be careful not to let the residual ink drop down from the Tube. 126
6 (19) Mark the new Tube at three points. The first mark: 260 mm from the end of the Tube The second mark: 20 mm from the first mark The third mark: 430 mm +/- 5 mm from the second mark End: (0 mm) Third mark: 715 or 705 ( /-5) mm First mark: 260 mm Second mark: 280 ( ) mm (20) Run the Tube through the Tube Guard from the end of the Tube near the first mark (marked in step (19)). Tube Guard (21) Run the Tube through the Tube Connector, and then insert the Tube into the Print Head. Tube Connector 127
7 (22) Fix the Tube to the Tube Holder aligning the first mark on the Tube (marked in step (19)) with the Print Head side s end of the Tube Holder. Head side Tube Holder First mark (23) Fix the Tube to the Tube Holder confirming that the second mark on the Tube (marked in step (19)) is aligned with the Ink Cartridge side s end of the Tube Holder. Ink Cartridge side Tube Holder Second mark (24) Fix the Tube to the Round Tube Holder aligning the third mark on the Tube (marked in step (19)) with the Round Tube Holder. Round Tube Holder Third mark 128
8 (25) Arrange the four Round Tube Holders on the Tube Holder Lower, and then fix the Tube Holder Upper to them with the screws. <Note> Be careful not to misarrange the Round Tube Holders. (26) Fit the Tube Clamp to the end of the Tube on the Needle side. Tube Clamp (27) Insert the Tube into the Needle, and then fasten the Tube Clamp. Tube Clamp 129
9 (28) Fix the Tube to the Tube Holder Small. Tube Holder Small (29) Fix the Tube to other Tube Holders. Tube Holder (30) Move the Carriage to the center position, and then fix the Tube to the Tube Holders (Upper/Lower) so that the Tube Holders are made level to the Carriage s moving direction. Carriage Tube Holders (Upper/Lower) 130
10 (31) Bind the Tubes with the Band (product name: Band, 1M). Band (32) Remove the Filter Cartridge, and then Insert the Ink Cartridge. Ink Cartridge (33) Mount the Ink Cartridge Cover U, Rear Cover, Back Cover and Front Cover, and then turn on. (34) Press the Platen Button to eject the Platen. (35) Press the OK Button to open the Menu Display. (36) Press the Up/Down Button to select Head Cleaning, and then press the OK Button. (37) Press the Up/Down Button to select Initial cleaning mode, and then press the OK Button. 131
11 (38) Press the Up/Down Button to select the color you have replaced the Tube, and then press the OK Button. The message Initial Cleaning Please Wait Head Cleaning. [X] appears, and the initial cleaning starts. The display returns to the Print Head color-selecting display when the initial cleaning has been completed. (39) Print and check the Nozzle Check Pattern (see Test Print ). 132
CN Remove the scanner assembly (X476 and X576 models) and all doors/covers.
CN598-67045 www.hp.com/support IMPORTANT: Ensure the product firmware is upgraded to at least version 1336MR before performing this repair procedure. If the firmware upgrade cannot be completed, contact
More informationMagelis XBT ZG43 Backlight Replacement Kit Quick Reference Guide
Magelis XBT ZG43 Backlight Replacement Kit Quick Reference Guide Thank you for purchasing the XBT ZG43 replacement backlight. Be sure to read the following Backlight Replacement Instruction bulletin prior
More informationManual placement system MPL3100. for BGA, CSP and Fine-Pitch components
Manual placement system MPL3100 for BGA, CSP and Fine-Pitch components Part No: MPL3100BA1.0e Issue Date: 02/2001 You have opted for an ESSEMTEC MPL3100 pick and place system. We thank you for this decision
More information3. Electronics and MMU2 unit assembly
Written By: Jakub Dolezal 2018 manual.prusa3d.com/ Page 1 of 34 Step 1 Tools necessary for this chapter Please prepare tools for this chapter: 2.5mm Allen key for M3 screws 2mm Allen key for nut alignment
More information"CHARM Access and operational Procedure
EDMS NO. REV. VALIDITY 1390490 0.1 DRAFT CERN CH1211 Geneva 23 Switzerland REFERENCE XXXX Date: 2015-09-04 OPERATING PROCEDURE "CHARM Access and operational Procedure ABSTRACT : The aim of this procedure
More informationInstruction manual. KUZMA 4POINT 14 inch TONEARM Serial Number:
Instruction manual KUZMA 4POINT 14 inch TONEARM Serial Number:.. 2016-09 1 KUZMA LTD INSTRUCTION MANUAL FOR 4POINT 14 tonearm The 4POINT 14 tonearm is a very precisely engineered piece of equipment, however,
More informationFC8600 SERIES CUTTING PLOTTER
FC8600 SERIES CUTTING PLOTTER MANUAL NO.FC8600-UM-151 TO ENSURE SAFE AND CORRECT USE To ensure the safe and correct use of your plotter, read this manual thoroughly prior to use. After reading this manual,
More informationOperation and Maintenance Guide Electric Needle Scalers
Operation and Maintenance Guide Electric Needle Scalers Models Covered Model Number ENS100V ENS200V Electric Needle Scaler, 110V-1ph Electric Needle Scaler, 220V-1ph Description IMPA Number 59 12 01 59
More informationAU5800 Every Other Week or Every 3,000 Samples (ISE) Maintenance. AU5800 Weekly (Analyzer and ISE) Maintenance
AU5800 Every Other Week or Every 3,000 Samples (ISE) Maintenance Step 1 Action Perform the Manually Clean the ISE Mix Bar, Liquid Level Sensors, Sample Pot and Sample Pot Tubing procedure AU5800 Weekly
More informationModWright Instruments, Inc. PH 150 Tube Phono Stage Owner s Manual
ModWright Instruments, Inc. PH 150 Tube Phono Stage Owner s Manual Manufactured by ModWright Instruments, Inc. 21919 399th St., Amboy, WA 98601 USA www.modwright.com 1 CAUTIONS: Do not operate or power
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PARTS REQUIRED Parts in the box Single monitor Dual monitor M2 M8 M/Flex + (package contents will depend on configuration ordered) Tools required for installation 6.0 mm Hex Key
More informationTimer Modules. EL11 24 Hour Module EL17 7 Day Module. Installation & Operating Instructions
Timer Modules EL11 24 Hour Module EL17 7 Day Module Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and retained for further reference and maintenance.
More informationK Service Source. Apple High-Res Monochrome Monitor
K Service Source Apple High-Res Monochrome Monitor K Service Source Specifications Apple High-Resolution Monochrome Monitor Specifications Characteristics - 1 Characteristics Picture Tube 12-in. diagonal
More informationInstruction Manual. from software version 1.0 (instruction version 1.3) Internet:
Instruction Manual from software version 1.0 (instruction version 1.3) email: service@glp.de Internet: http://www.glp.de GLP German Light Production (V1.3) 1 Table of contents 1 Description of Device...
More informationKUZMA 4POINT TONEARM
KUZMA 4POINT TONEARM Instruction manual 2008-6 Serial Number:.. 1 KUZMA LTD INSTRUCTION MANUAL FOR 4POINT tonearm The 4POINT tonearm is a very precisely engineered piece of equipment, however, the construction
More informationOptical Distribution Box 300 Installation Guide. Version : R0.0
Optical Distribution Box 300 Installation Guide Document No. : OD16-546-L-01 Version : R0.0 Date: 21-Mar-2018 IMPORTANT INSTRUCTIONS When using fiber optic equipment, basic precautions should always be
More information3G-SDI Fiber Optic Digital Extension Modules in 19 1RU Frame
WWW.OPTICIS.COM 3G-SDI Fiber Optic Digital Extension Modules in 19 1RU Frame User s Manual (BR-300 / BR-310) Doc No. : OSE-SDI150102-BR300 / Rev1.2-1 - Contents Welcome!...- 3 - Product Description...-
More informationYoke Safety cable loop. Up Light Bulb
Source Four LED Profile Overview For complete information and step-by-step instructions, see the User Manual. ETC documentation can be downloaded at www.etcconnect.com. Yoke Safety cable loop Yoke locking
More informationBriggs&Stratton 44Q B1
Accessories IPL, Briggs&Stratton 44Q777-1272-B1, 2010-03 Briggs&Stratton 44Q777-1272-B1 Spare parts Ersatzteile Pièces détachées Reserve onderdelen Repuestos Reservdelar 48 SHORT BLOCK 1329 REPLACMENT
More informationBionic Elephant Trunk. Assembly Instructions
Bionic Elephant Trunk Assembly Instructions Equipment and Supplies Required items from the Bionics Kit and/or Materials Pack: 1. Tail fin (small) assembled 2 see Start Here for tail fin assembly instructions
More informationFully ly Automaticti. Motorised Satellite t TV System. User s manual REV
REV. 1.0 Fully ly Automaticti Motorised Satellite t TV System User s manual Customer Help Line: 1300 139 255 Support Email: support@satkingpromax.com.au Website: www.satkingpromax.com.au www.satkingpromax.com.au
More informationGENUINE PARTS CAUTION
GENUINE PARTS SATELLITE RADIO INSTALLATION INSTRUCTIONS 1. DESCRIPTION: SATELLITE RADIO SYSTEM 2. PART NUMBERS: XM tuner kit 999U9-NV003 XM antenna kit 999U9-VR000 Sirius tuner kit 999U9-NV004 Sirius antenna
More informationSystem Power Supply 4. User Guide
System Power Supply 4 User Guide 2017 Schnick-Schnack-Systems GmbH Situation at August 2017: All technical data as well as the weight and dimension information were carefully created errors reserved. Any
More informationK Service Source. Apple High-Res Monochrome Monitor
K Service Source Apple High-Res Monochrome Monitor K Service Source Specifications Apple High-Resolution Monochrome Monitor Specifications Characteristics - 1 Characteristics Picture Tube 12-in. diagonal
More informationRemote Control Operation
Remote Control Operation When you first switch the TV on, you will be presented with either the preview screen which shows the current program along with a brief summary of future programs or the full
More informationINSTRUCTIONS FOR USE Pro-Ject 2 Xperience SB S
INSTRUCTIONS FOR USE Pro-Ject 2 Xperience SB S 2 Pro-Ject 2 Xperience SB S Controls, features and connections 1 Motor transport foam inserts 2 Motor with motor pulley 3 Drive belt * 4 Sandwich platter
More informationLED Pixel Track Pro ORDERCODE 42205
LED Pixel Track Pro ORDERCODE 42205 Congratulations! You have bought a great, innovative product from Showtec. The Showtec LED Pixel Track Pro brings excitement to any venue. Whether you want simple plug-&-play
More informationPRODUCT SPECIFICATIONS
FOS Beam 150W 1 PRODUCT SPECIFICATIONS TECHNICAL SPECIFICATION Voltage: 100/240 Volt AC, 50/60 Hz. Power Consumption: 250 Watt. Light Source: 150 Watt LED, 6800K Beam angle: 2 Colors: 11 dichroic color
More informationModel: S-1071H 7" Broadcast On-camera 3GSDI&HDMI LCD Monitor. User Manual. Please read this User Manual throughout before using.
Model: S-1071H 7" Broadcast On-camera 3GSDI&HDMI LCD Monitor User Manual Please read this User Manual throughout before using. Preface Congratulations on your purchase of this product. Please read this
More informationTECHNICAL GUIDE. TOUGH GUN ThruArm G1 Series Robotic MIG Guns for FANUC Robots 100iC, 100iC-12, 100iC-6L, 100iC-7L, 120iC, 120iC-10L, 120iC-12L
TECHNICAL GUIDE TOUGH GUN ThruArm G1 Series Robotic MIG Guns for FANUC Robots 100iC, 100iC-12, 100iC-6L, 100iC-7L, 120iC, 120iC-10L, 120iC-12L INSTALLATION MAINTENANCE TECHNICAL DATA OPTIONS EXPLODED VIEW
More informationColumn Type Air Micrometer. CAG2000 Instruction Manual
Column Type Air Micrometer CAG2000 Instruction Manual Contents 1. Introduction 1 2. Main Features 1 3. Main Modes 2 4. Names and Functions of Controls and Parts 3 5. Specifications 8 6. Measurement 10
More informationProjector PH1201QL. User s Manual INSTALLATION AND QUICK-START GUIDE CONNECTION GUIDE OPERATING GUIDE REFERENCE GUIDE. Model No.
Projector PH1201QL User s Manual INSTALLATION AND QUICK-START GUIDE CONNECTION GUIDE OPERATING GUIDE REFERENCE GUIDE Model No. NP-PH1201QL About This Document Follow the instructions in this manual carefully
More informationINSTRUCTION AND MAINTENANCE VIDEO MOTORE PROJECTION SCREEN
INSTRUCTION AND MAINTENANCE VIDEO MOTORE PROJECTION SCREEN 1.1 TECHNICAL DATA PRODUCT DESCRIPTION Screens made with the following projection fabrics: SOFT WHITE, MATT WHITE SOFT, SOFT WHITE TRANSOUND,
More informationThe Illustrated manual for. Clow 103
The Illustrated manual for Clow 10 Contents Lights...1 Turning on the system... Microphones... 4 Turning the video projector on and off... 6 The screen... 7 VHS videocassette recorder...8 Computer... 10
More informationUSER S MANUAL. Thank you very much for purchasing this product.
USER S MANUAL Thank you very much for purchasing this product. To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read through this manual completely
More informationPRODUCT DESCRIPTION N3S
PRODUCT DESCRIPTION N3S Nexans N3S ODF system NEXANS N3S ODF SYSTEM Contents Contents Systems description Patching frame Splice frame Patching module (KB 104/109) Splicing module Accessories Page 2 Page
More informationINSTALLATION AND OPERATING MANUAL FOR ALL MATSUKO SWITCHBOX MODELS SWB 5 SWB 5P SWB 5P+PG WARNING:
MSB12906121MAN UK English INSTALLATION AND OPERATING MANUAL FOR ALL MATSUKO SWITCHBOX MODELS SWB 5 SWB 5P SWB 5P+PG WARNING: Ensure that the Matsuko Switchbox is switched off at the mains before you attempt
More informationFlat LED Par Can Light
Flat LED Par Can Light EDD-GL-200 USER MANUAL 1. Introduction 3 Thank you for purchasing our Million Color Flat LED light. Please read these instructions carefully before operating to avoid any possible
More informationGazer VI700A-SYNC2 and VI700W- SYNC2 INSTALLATION MANUAL
Gazer VI700A-SYNC2 and VI700W- SYNC2 INSTALLATION MANUAL Contents List of compatible cars... 3 Package contents... 4 Special information... 6 Car interior disassembly and connection guide for Ford Focus...
More informationTV CHANNEL INSTALLATION
LCD TV TV CHANNEL ATION Immediately after unpacking and plugging in your new television, run the auto program function to set up the TV for the broadcast or cable channels available in your area. If you
More informationOWNER S MANUAL MOTORIZED 7 WIDE TFT LCD COLOR MONITOR CNT-701
OWNER S MANUAL PW MOTORIZED 7 WIDE TFT LCD COLOR MONITOR CNT-701 ANY CHANGES OR MODIFICATIONS IN CONSTRUCTION OF THIS UNIT DEVICE WHICH IS NOT APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIACE COULD VOID
More informationK Service Source. Apple Two-Page Mono Monitor
K Service Source Apple Two-Page Mono Monitor K Service Source Basics Two-Page Monochrome Monitor Basics Monitor Distortion - 1 Monitor Distortion Overview Ideal Raster All large-screen monitors are susceptible
More informationPhone (440) Fax Wireless Rear Observation System With Night Vision Camera
www.buyersproducts.com Phone (440) 974-8888 Fax 800-841-8003 8883200 Wireless Rear Observation System With Night Vision Camera 1 Table of Contents What's in the Box?...3 Introduction...4 Safety Information...5-6
More informationFigure 1: V 713 CI plug-in card
Version 04-2013A Device description Device description The delivery consists of the following parts: V 713 CI and X-DVB-CT2/PAL duo CI plug-in cards 2 connection cables with F connectors, 450 mm & F socket-f
More informationEdition Notes. Edition Notes. Trademarks CHAUVET is a registered trademark of CHAUVET & Sons, LLC. (d/b/a CHAUVET or Chauvet).
User Manual Edition Notes Edition Notes The OVATION Min-E-10CW User Manual Rev. 3 covers the description, safety precautions, installation, programming, operation, and maintenance of the OVATION Min-E-10CW.
More informationTimer Modules. MEU11 24 Hour Module, MEU17 7 Day Module (Without Housing)
Timer Modules MEU11 24 Hour Module, MEU17 7 Day Module (Without Housing) EMU11 24 Hour Module, EMU17 7 Day Module (With Housing Giving panel mounting facility) Installation & Operating Instructions 1 1.
More information3B SCIENTIFIC PHYSICS
3B SCIENTIFIC PHYSICS Complete Fine Beam Tube System 1013843 Instruction sheet 10/15 SD/ALF If it is to be expected that safe operation is impossible (e.g., in case of visible damage), the apparatus is
More informationETC Quick Guide. Source Four LED Profile
ETC Quick Guide Source Four LED Profile Overview For complete information and step-by-step instructions, see the Source Four LED Profile User Manual. ETC documentation can be downloaded at www.etcconnect.com.
More informationTen-Tec (865) Service Department:(865)
Ten-Tec (865) 453-7172 Service Department:(865) 428-0364 Installation Instructions for Ten-Tec Jupiter AT538K Tuner Kit The installation of the AT538K is divided into two steps. The first step is to reprogram
More informationP-2 Installing the monitor (continued) Carry out as necessary
P-2 Installing the monitor (continued) Carry out as necessary Using the monitor without the bezel MDT552S satisfies the UL requirements as long as it is used with the bezel attached. When using the monitor
More informationCM MTC PARTS LIST
8650 Enterprise Drive, Peosta IA 52068-0050 319-556-7484 / Fax 319-556-1235 CM-2400-0MTC PARTS LIST ENGINE OIL GRADE: ENGINE OIL CAPACITY: PUMP OIL: PUMP OIL CAPACITY: NOZZLE SIZE: 30W 21 oz. MI-T-M #AW-4085-0016
More information3M Locator Plate N
M Locator Plate 44-107N Instructions for the assembly of.100 x.100 preassembled socket connectors 1.0 General The M Locator Plate 44-107N is designed to aid in the assembly of the preassembled socket connector
More informationHCS - HES Cabling Systems
HCS - HES Cabling Systems Installation Manual for HCS High-Capacity Fiber-Optic Rack-Mount Cabinets Be sure to read and completely understand this procedure before applying product. Be sure to select the
More informationSpectra/Chrom Chart Recorder from Spectrum Chromatography
Spectra/Chrom Chart Recorder from Spectrum Chromatography D20140 180296 Copyright 1996 by Spectrum Chromatography PO Box 672026 Houston, TX 77267-2026 Phone: (281) 443-2900 (800) 459-9700 (US & Canada)
More informationThingMagic RFID Module INSTALLATION GUIDE. FOR CL e SERIES
ThingMagic RFID Module INSTALLATION GUIDE FOR CL e SERIES SATO International Pte Ltd 438A Alexandra Road #05-0/02 Alexandra Technopark Singapore 9967 Tel: (65) 627 222 Fax: (65) 627 25 Email: customerservice@sato-int.com
More informationSCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS FROM 300 cm. UP TO 450 cm. of width
SCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS FROM 300 cm. UP TO 450 cm. of width Before installing the screen winch system, please read the following instructions carefully: The screen winch system
More informationIRIG-B PTP Clock Converter Output Module Hardware Installation Manual
IRIG-B PTP Clock Converter Output Module Hardware Installation Manual Kyland Technology Co., LTD. Publication Date: May 2012 Version: V1.2 Customer Service Hotline: (+8610) 88796676 FAX: (+8610) 88796678
More informationNC-1000 INSTALLATION MANUAL NC-1000 FIBRE OPTIC CROSS-CONNECTION SYSTEM
NC-1000 INSTALLATION MANUAL NC-1000 FIBRE OPTIC CROSS-CONNECTION SYSTEM Content 1. General 5 2. The products of NC-1000 system 6 3. Mounting of the frame 8 4. Earthing of the frame 8 NC-1000 FIBRE OPTIC
More informationLED Pixel Track V3 ORDERCODE 42200
LED Pixel Track V3 ORDERCODE 42200 Congratulations! You have bought a great, innovative product from Showtec. The Showtec LED Pixel Track brings excitement to any venue. Whether you want simple plug-&-play
More informationAP-40. AP-40 Series Features Industry s smallest-sensor head Ultra lightweight High-speed response Two-color LED digital pressure display
AP-34 Separate Amplifier Type Sensor Series Features Industry s smallest-sensor head Ultra lightweight High-speed response Two-color LED digital pressure display Description Industry's smallest & lightest
More informationINSTRUCTIONS FOR USE Pro-Ject RPM 10 Carbon
INSTRUCTIONS FOR USE Pro-Ject RPM 10 Carbon 2 Pro-Ject RPM 10 Carbon Controls, features and connections 1 Separate motor unit (motor and motor base) * 2 Drive pulley 3 Drive belt * 4 Speed control button
More informationINSTALLATION INSTRUCTIONS MO023A
INSTALLATION INSTRUCTIONS MO023A Nexans N3S ODF system NEXANS N3S ODF SYSTEM Content Product description Patching frame Splice frame Doors Splice module Patch module Protective cover and label panel Guides
More information9.5 Add or Remove Samples in Single Access Mode
3. Press the Previous or Next button to see the details of the previous or next loaded position. 4. Press the Back button to return to the information screen. The previous menu is displayed. 9.5 Add or
More informationr.link Video-inserter RL5-MIB-STD2
r.link Video-inserter RL5-MIB-STD2 Video-inserter with 1 video input and 1 rear-view camera input Compatible with VW vehicles with Composition Media or Discover Media system Skoda vehicles with Amundsen
More informationLED Backlight for Technics amplifiers
LED Backlight for Technics amplifiers Technics SE-A900S Technics SE-A900SM2 Technics SE-A909S Technics SE-A1000 Technics SE-A1000M2 Technics SE-A1010 Rev. 1.2 B Description The LED module is designed to
More informationDigital Modulator Instructions
Product Code: CCT818 ANTIhum.com Digital Modulator Instructions Features Tunable output channel from 21-69, Push button channel selection, Microprocessor tuning, Channel Memory, Audio input, LED channel
More informationPRODUCT SPECIFICATIONS
FOS RGB Fan 1 PRODUCT SPECIFICATIONS TECHNICAL SPECIFICATION Voltage: 110/240 Volt AC, 50/60 Hz. Power Consumption: 180 Watt. Light Source: 792x 0,2 Watt RGB SMD 5050 LEDs. Effects: LEDs are separated
More information1440/2880 HP RGB+WW+CW
office Nano*Pix 1440/2880 HP RGB+WW+CW User Manual Rev 7/2014 V4.4 Specifications subject to change without notice. Seite 1 Product Description Thank you for choosing this LDDE Nano*Pix 1440 HP / 2880
More informationMotor Operated Solar Shade with Valance Installation and Care Instructions Complete Video Instructions Available Online at
* Motor Operated Solar Shade with Valance Installation and Care Instructions Complete Video Instructions Available Online at www.keystonefabrics.com Step 1: Identify the parts of your shade (parts shown
More informationSTIMULUS CONTROLLER, Type CS-55 INSTRUCTIONS
, Type INSTRUCTIONS 2015 Reproduction of text and/or drawings is permitted for personal use. The use of reproductions in publications is only allowed if correct reference is made to 1 2 3 6 7 4 5 8 9
More information4320 SS-25 Self-Strip Terminating Block
4320 SS-25 Self-Strip Terminating Block Instructions May 2002 78-8130-7677-1 1.0 General The 3M 4320 SS-25 Self-Strip Terminating Block is a factory stubbed, self-stripping connecting block designed for
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BEFORE INSTALLING OR ADJUSTING THIS PRODUCT, PLEASE READ THESE INSTRUCTIONS CAREFULLY. PLEASE KEEP THIS GUIDE FOR FUTURE REFERENCE FIBER OPTIC SWING-OUT PATCH PANEL INSTRUCTION
More information2179-CD Series Fiber Optic Splice Closure. Installation Instructions
2179-CD Series Fiber Optic Splice Closure Installation Instructions 1.0 Product Introduction The new 3M TM 2179-CD Series Fiber Optic Splice Closure can be used in buried, underground, aerial, and pedestal
More informationDATA Count and Fill S 60
DATA Detection Technologies Ltd. DATA Count and Fill Series DATA Count and Fill S 60 Operation and Maintenance Manual April 2012 PROPRIETARY AND CONFIDENTIAL Copyright 2010 by Data Technologies Ltd. All
More informationLCS 2 RJ 45 Cat. 6A HD panels and units
87045 LIMOGES Cedex Telephone: (+33) 05 55 06 87 87 - Fax: +33 (0)5 55 06 88 88 Page 0 335 85/86 1. General characteristics....1 2. Presentation...1 3. Positioning...1 4. Technical characteristics...1
More informationInteractive Satellite Terminal Installation / Validation Manual
Installation / Validation Manual Version October 5, 2016 Index INTERACTIVE SATELLITE TERMINAL 1. FCC COMPLIANCE... 3 2. TECHNICAL FEATURES...4 3. GENERAL DESCRIPTION...5 4. ELEMENTS CONTAINED IN THE TERMINAL...6
More informationHalsey 106. For assistance and additional equipment, contact Halsey Instructional Technology Services Halsey 259, extension 4979
The Illustrated manual for Halsey 106 Contents The master power switch...1 Screen...3 Turning on the projectors...4 Turning off the projectors...5 Microphones... 6 projectors... 9 Installed Computers...
More informationScan-Light Supplement. Fitting instructions and hardware details For Mitsubishi MH105AG and MH216CG scanners
Scan-Light Supplement Fitting instructions and hardware details For Mitsubishi MH105AG and MH216CG scanners Contents Contents Fitting instructions and hardware details... 1 For Mitsubishi MH105AG and MH216CG
More informationQuick Operation Guide of LTN7700/7600 Series NVR
Quick Operation Guide of LTN7700/7600 Series NVR UD.6L0202B0042A02 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual is applicable
More informationLED-BANK4 USER MANUAL. COLORbank 4
LED-BANK4 COLORbank 4 USER MANUAL CHAUVET, 3000 N 29 th Ct, Hollywood, FL 33020 U.S.A (800) 762-084 (954) 929-5 FAX (954) 929-5560 www.chauvetlighting.com 2006-04-8/6:44 Table of Content BEFORE YOU BEGIN...
More informationALO 030 MKII. 30 Watt DMX LED scanner. User manual
ALO 030 MKII 30 Watt DMX LED scanner User manual Safety instructions WARNING! Always keep this device away from moisture and rain! Hazardous electrical shocks may occur! WARNING! Only connect this device
More informationQuick Setup Guide. DCX-500i / DCX-1000i / DCX-1500i Projectors with WC-Pro Scaler. Preliminary
Quick Setup Guide DCX-500i / DCX-1000i / DCX-1500i Projectors with WC-Pro Scaler Preliminary Table of Contents Introduction... 1 Connecting the Projector... 1 Installing the Primary Lens... 2 Connecting
More informationWhen you load media, you must place the roll onto the media hangers. You must use the correct media for the type of printing you require.
Getting Started 13 When you load media, you must place the roll onto the media hangers. You must use the correct media for the type of printing you require. Preparing Media Whether your roll media is inside
More informationSCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS UP TO 300 cm. of width
SCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS UP TO 300 cm. of width Before installing the screen winch system, please read the following instructions carefully: The screen winch system must be used
More informationFigure 1: V 613 CI plug-in card
Version 02-2013A Device description Device description The delivery is comprised of the following parts: V 613 CI and X-DVB-S2/PAL duo CI plug-in card 2 connection cables with F connectors, 450 mm & F
More informationFlorida State University Thayumanasamy Somasundaram
2016 Florida State University 2013-16 Thayumanasamy Somasundaram [PANALYTICAL X-PERT PRO POWDER DATA COLLECTION] A quick start-up procedure for collecting powder x-ray diffraction data from PANalytical
More informationivw-fd122 Video Wall Controller MODEL: ivw-fd122 Video Wall Controller Supports 2 x 2 Video Wall Array User Manual Page i Rev. 1.
MODEL: ivw-fd122 Video Wall Controller Supports 2 x 2 Video Wall Array User Manual Rev. 1.01 Page i Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice
More information3M Coupling Tray FDTC-10S-COUPLINGTRAY
3M Coupling Tray FDTC-10S-COUPLINGTRAY for use with 3M Fiber Dome Closures FDC 10S Instructions July 2010 3 1.0 Introduction The 3M Coupling Tray FDTC-10S-COUPLINGTRAY can accommodate up to 10 loose tubes.
More information16A Announcement System Description and Operating Procedures
Lucent Technologies Practices 201-523-101, Issue 4.1 16A Announcement System Description and Operating Procedures Help Line 1-800-352-5563 (calls within USA) 1-973-386-4311 (calls outside USA) Contents
More information120cm (4x36 Watt) incl. Splitter Instruction Manual
120cm incl. Splitter Instruction Manual Table of contents 1 Description of Device and Functions... 3 1.1 Safety Instructions... 4 2 Preparation and Installation... 5 2.1 Mounting... 5 2.2 Secure the...
More informationREAD THIS FIRST. Morphologi G3. Quick Start Guide. MAN0412 Issue1.1
READ THIS FIRST Morphologi G3 Quick Start Guide MAN0412 Issue1.1 Malvern Instruments Ltd. 2008 Malvern Instruments makes every effort to ensure that this document is correct. However, due to Malvern Instruments
More informationSUBCARRIER TRANSFER FILTER INSTRUCTION BOOK IB622702
SCF611S SUBCARRIER TRANSFER FILTER INSTRUCTION BOOK IB622702 SCF611S SUBCARRIER TRANSFER FILTER TABLE OF CONTENTS PAGE SHIPPING INSPECTION 2 MODULE CONFIGURATION 2 INSTALLING MODULES 2-3 CABLING 3 FRONT
More informationSL-OCT Video-Kit. Installation Manual. Revision 001, March Heidelberg Engineering GmbH
SL-OCT Video-Kit Installation Manual Revision 001, March 2008 Heidelberg Engineering GmbH Art. No.: 96 048-001 Page 2 of 24 Corporate Headquarters Heidelberg Engineering GmbH Tiergartenstrasse 15 69121
More informationGuía del usuario Español ( 7 10 ) Guide d utilisation Français ( ) Guida per l uso Italiano ( ) Benutzerhandbuch Deutsch ( )
User Guide English ( 3 6 ) Guía del usuario Español ( 7 10 ) Guide d utilisation Français ( 11 14 ) Guida per l uso Italiano ( 15 18 ) Benutzerhandbuch Deutsch ( 19 22 ) Appendix English ( 23 ) User Guide
More informationELLIPTICAL ANTENNA E0851B11
ELLIPTICAL ANTENNA E0851B11 INSTALLATION GUIDE E0851B11 Installation Manual Step 1: Finding a suitable antenna site A suitable antenna site requires an unobstructed view and a stable antenna mounting surface.
More informationElectric Motorized Projection Screen PowerMax Tension Series
Electric Motorized Projection Screen PowerMax Tension Series User s Guide Important Safety & Warning Precautions Make sure to read this user s guide and follow the procedures below. Caution: The screen
More informationAssembling and Mounting the Presentation Display, Speakers, Speaker Screens, and Table Door
CHAPTER 8 Assembling and Mounting the Presentation Display, Speakers, Speaker Screens, and Table Door July 13, 2012, This document provides you with the procedures you perform to assemble and mount the
More informationINSTRUCTIONS FOR USE Pro-Ject Primary Phono USB
INSTRUCTIONS FOR USE Pro-Ject Primary Phono USB 2 Pro-Ject Audio Systems Pro-Ject Primary Phono USB/ Pro-Ject 8.6E Revision 2015.08.28 Pro-Ject Primary Phono USB Controls, features and connections 1 Power
More informationDigital satellite antenna with control panel. Kronings MobilSat +
Digital satellite antenna with control panel User s Manual Models: MSP-S / MSP-C SUMMARY 1. Introduction... 2 1.1. Usage... 2 1.2. General notes... 3 1.3. The Control Panel... 3 2. Base functions... 4
More informationG-Mix 200 Moving Head Getting Started 3
Blizzard Lighting, LLC www.blizzardlighting.com Waukesha, WI USA Copyright (c) 2017 TABLE OF CONTENTS G-Mix 200 Moving Head 1 1. Getting Started 3 What s In The Box? 3 Getting It Out Of The Box 3 Powering
More information