Mini Gear Indicator Manual SW024
|
|
- Sherilyn Bennett
- 6 years ago
- Views:
Transcription
1 General Mini Gear Indicator Manual SW024 This Gear Indicator is designed to work on motorbikes with digital rev and speed signals. The current gear is displayed on a 7 segment LED display. The Gear Indicator determines the gear by measuring and calculating the frequency ratio between rev and speed signal and by checking the status of the neutral switch. No indication is possible if one of these signals is missing. Luminosity of the display is changeable in 10 steps. Gear recognition has to be teached according to the individual bike type. A few bike types are already pre-saved for easy retrieval. Manual or automatic setting is also possible. The device is controlled by a single button, placed on the backside. To find your given software version use menu item 8, it has to fit to the version in the title of this document. Older manuals are still valid as long as no newer version is released. Normal Operation The Gear Indicator starts working with ignition switch-on. During normal operation the following readouts are possible: Readout Function Neutral Gear 1 Gear 2 Gear 3 Gear 4 Gear 5 Gear 6 No valid signals, gear can not be determined (standstill, clutch slipping, etc.) Brightness Brightness of the display can be changed in 10 steps (menu #1). cvieth@arcor.de 1/5 Version 24, April 2012
2 Settings menu Mini Gear Indicator Manual SW024 A simple menu structure is implemented to alter settings. The button is used for navigation: - Keep button pressed until appears, release button. Menu mode is now engaged. - Display shows 0 and counts up with each subsequent click to the button. After two seconds of inactivity the number of clicks is taken as jump position into the menu according to the following list. All clicks are counted but only the least digit is displayed: # of clicks / item Display Description 1 Flashing value Change brightness. Values Keep button pressed until desired value is reached. 2 4,5 or 6 Number of gears. Keep button pressed until desired values is reached. 3 Flashing digit, current gear to be teached Teaching the gears: - Ride in the given gear and press button, wait until next digit appears - Repeat for all gears 4 Save Neutral recognition, high or low signal logic. Toggle function. 5 Save Neutral Sign, 0 or N. Toggle function. 6 7 Single segment running in a circle Single segment running in a circle Check for correct speed signal. Only display, no setting. Each tick of the moves the segment one position. Rotate the wheel slowly by hand. Check for correct rev signal. Only display, no setting. Each 40 th tick of the engine moves the segment one position. Let the engine run at idle Version number of the Software. Only display, no setting. 1 flashing Recognition Gear 1, quotient with 4 decimals. 2 flashing Recognition Gear 2, quotient with 4 decimals. 9 3 flashing Recognition Gear 3, quotient with 4 decimals. 4 flashing Recognition Gear 4, quotient with 4 decimals. 5 flashing Recognition Gear 5, quotient with 4 decimals. 6 flashing Recognition Gear 6, quotient with 4 decimals. cvieth@arcor.de 2/5 Version 24, April 2012
3 F1 flashing Recognition Error high (gear above 6), quotient with 4 decimals. 10 F2 flashing Recognition Error low (gear below 1 and not neutral), quotient with 4 decimals. d flashing Delaytime before a new gear is accepted, 2 decimals, range = immediate response 11 Save Weak/Change Signal Indicator. If set to ON the decimal point becomes active while the actual gear does not match to the electronic signals. The electronics calculates for the new gear and waits for the given delaytime until displayed. Toggle function on/off. 14 Save Reset all setting to factory default. 15 Save Slow Clocked Signals. Option for better signal handling on bikes with only a single speed click per rotation. 16 Delay Factor flashing 17 Averaging Factor flashing Gear Delay Time. Delaytime for gear change recognition Averaging Factor. Minimum number of consecutive identical values before a new gear is recognized. 1 = minimum, instantly any other Save Quick preset to optimal parameters for selected bikes. 20 = FZS1000 (= FZ1 gen 1) 21 = FZ1 (gen 2) 22 = FZS = MZ SM = FZ6 25 = Honda CBR1100XX 26 = FZ8 Back to normal operation Only one item can be selected at a time. Mode changes back to normal at the end of each item. Re-enter the menu for further changes. General behaviour for editing: A short click leads to the next entry (or sub-item if present) without any change. A long keypress changes the actual displayed value. Keep pressed and release if the desired value comes along. Storing of changes is indicated by SAVE. In case of doubt switch off ignition and restart. cvieth@arcor.de 3/5 Version 24, April 2012
4 Menu 1, toggling brightness - Switch on ignition. - Press 1 time to jump to menu 1, display counts up. - Keep button pressed until desired brightnes is reached. Loop continuous to run from 0 to 9 until released. - Brightness changes and display reads SAVE. - Automatic return to normal operation Menu 3, teaching new gears A manual teaching has to be applied if no preset (menu 20 to 26) fits. This might also become necessary in case of an installed speedohealer. - Switch on ignition. Start engine. - Press 3 times to call menu #3, display counts up. - Display flashes constanly with the gear to be teached. Ride the bike constantly at about 3000rpm. - Press the button, the display shows for some seconds. At this point the electronic tries to determines the gear. On success it reads. (On failure it reads, restart from the beginning) - Repeat the procedure for all gears. At the end the display shows SAVE and jumps back to normal operation. Menu 9, changing / viewing gear recognition values manually This procedure is a bit difficult, menu 3 should be used preferably. - Switch on ignition. - Press 9 times to call menu 9, display counts up. - Display flashes with actual changeable gear 1. There are 3 possible actions: display only, changing manually, automatic detection during test run: Display only: o Short click, all 4 decimals will be shown one after another, most significant coming first. o At the end the next gear is flashing. o Repeat for all gears. o Automatic jump back to normal operation. cvieth@arcor.de 4/5 Version 24, April 2012
5 Manual change: o Short click, all 4 decimals will be shown one after another, most significant coming first. o If the desired decimal comes along press and keep the button. The value will now be altered slowly in an endless loop. Release button if the desired value is reached. o Repeat for remaining decimals if required. Otherwise proceed as described in Display only. o Changes will be stored automatically. Automatic detection by test run (only for gear 1 to 6 ): o Keep button pressed until 3 horizontal bars appear, release. Now the electronic waits for teaching to be started. o Ride with the bike with the respective gear at moderate and constant revs. o Press button shortly to start teaching. Several segments start flashing while teaching is in progress. Ready after a few seconds. o Afterwards all 4 decimals will be shown sequently. o Repeat for further gears or skip with as with Display only. Specialities: Item d (Delaytime) only got 2 decimals. Values for F1 and F2 will be calculated automatically (suggested), unless they are edited intentionally. All modified values will be saved instantaneously, the display reads S-A-V-E. During teaching the signals should be centered by means of rev and speed, 4000 rpm is a good choice. Presets: Speed/Revs-quotient and delays. By calling menu items all settings will be presetted to the respective optimal values. Gang / Parameter FZS1000 FZ1 FZS F F D cvieth@arcor.de 5/5 Version 24, April 2012
Pre-processing of revolution speed data in ArtemiS SUITE 1
03/18 in ArtemiS SUITE 1 Introduction 1 TTL logic 2 Sources of error in pulse data acquisition 3 Processing of trigger signals 5 Revolution speed acquisition with complex pulse patterns 7 Introduction
More informationHome Page 1 Press the House button I E
A Home Page 1 Press the House button B C F D G Clutches Manual Disconnects H I E 1 2 3 4 J 5 6 7 8 K L A) Target Population Press button to change target population B) Average population C) QS Reset Quick
More informationOwners SW-LCD 2.0 Manual & Specifications
Owners SW-LCD 2.0 Manual & Specifications Contents 1. Preface. 19 2. Appearance and Size.20 2.1 Material and Color 20 2.2 Display Size and Installation Size 20 3. Function Summary and Button Definition
More informationPC/HDTV to PC/HDTV converter (CP-251F)
PC/HDTV to PC/HDTV converter (CP-251F) Operation Manual This Converter has been especially modified to also accept RGsB Sync on Green Operation Controls and Functions Front Panel 1. Reset/ and +- The and
More informationInspire Station. Programming Guide. Software Version 3.0. Rev A
Inspire Station Programming Guide Software Version 3.0 Rev A Copyright 2016 Electronic Theatre Controls, Inc. All rights reserved. Product information and specifications subject to change. Part Number:
More informationInstruction manual. DALI Gateway art Installation manual
Instruction manual DALI Gateway art. 01544 Installation manual Contents GENERAL FEATURES AND FUNCTIONALITY from page 5 ETS PARAMETERS AND COMMUNICATION OBJECTS from page 6 COMMUNICATION OBJECTS GENERAL
More informationEDL8 Race Dash Manual Engine Management Systems
Engine Management Systems EDL8 Race Dash Manual Engine Management Systems Page 1 EDL8 Race Dash Page 2 EMS Computers Pty Ltd Unit 9 / 171 Power St Glendenning NSW, 2761 Australia Phone.: +612 9675 1414
More informationPlease read this manual before using the C961 Display. Suzhou Bafang Electric Motor Science-Technology Co., LTD
Manual C961 Contents Material & color 3 Functions & buttons 3 Functions 3 Interface 4 ON/OFF 5 The display switches off automatically if there is no activity for ten minutes (default). 5 Walking assist
More informationC Module Description
IQMMX -Input Router & ASI Distribution Amplifier C Module Description The IQMMX is an ASI to 1 switch, distribution amplifier and transport stream switcher with up to 8 outputs in double width form or
More informationC O B A R 18R U s e r G u i d e P a g e 1. User Guide COBRA 18R. Wireless Firing System.
C O B A R 18R U s e r G u i d e P a g e 1 User Guide COBRA 18R Wireless Firing System C O B A R 18R U s e r G u i d e P a g e 2 TABLE OF CONTENTS 1. SYSTEM INTRO... 3 2. POWER ON... 4 3. REMOTE / FIRING
More informationVariwrap Controller Manual
Variwrap Controller Manual Operation The controller has two operating modes Manual and Auto. The mode is changes by pressing the (F1) Auto/Manual button. The mode setting is displayed in the top right
More informationKING-METER USER GUIDE SW-LCD
KING-METER USER GUIDE SW-LCD Contents 1. Preface.3 2. Appearance and Size 4 2.1 Material and Color 4 2.2 Display Size and Installation Size 4 3. Function Summary and Button Definition 5 3.1 Preset and
More informationSample BD Tech Concepts LLC
XYZ Corp. Fry Controller FC-1234 Software Test Procedure Copyright 2014 Brian Dunn BD Tech Concepts LLC Last Modified: 00/00/0000 Version Tested: Date Tested: Technician: Results: 1 FC-1234 SW Test Proc.
More informationRadio Thermostat Clock
Radio Thermostat Clock Installation & User Instructions Part number: ZU0800009 80.10.1375.7_feeling_ks_fer_en.indd 1 18.04.2013 11:25:42 Table of contents Safety instructions... 3 Product details... 4
More informationED3. Digital Encoder Display Page 1 of 13. Description. Mechanical Drawing. Features
Description Page 1 of 13 The ED3 is an LCD readout that serves as a position indicator or tachometer. The ED3 can display: Speed or position of a quadrature output incremental encoder Absolute position
More informationIntroduction Display...1 Mounting...1 Firmware Version...2. ADL Operation... 3
MoTeC MDD User Manual Contents Introduction... 1 Display...1 Mounting...1 Firmware Version...2 ADL Operation... 3 1. Full ADL Display...4 2. Gain Loss Layout for ADL...6 3. Large Numeric Layout for ADL...8
More informationDDA-UG-E Rev E ISSUED: December 1999 ²
7LPHEDVH0RGHVDQG6HWXS 7LPHEDVH6DPSOLQJ0RGHV Depending on the timebase, you may choose from three sampling modes: Single-Shot, RIS (Random Interleaved Sampling), or Roll mode. Furthermore, for timebases
More informationwith the Field-IQ Crop Input Control System
with the Field-IQ Crop Input Control System Quick Reference Card CONNECTING THE SYSTEM Ag25 GNSS antenna (P/N 68040-OOS) TNC/TNC right-angle cable (P/N 50449) Cable assembly, display to Field-IQ (P/N 50449)
More informationUser Instruction Manual IQSDA30/IQSDA32. Intelligent Reclocking High Performance HD-SDI/SD-SDI Distribution Amplifiers. snellgroup.
User Instruction Manual IQSDA30/IQSDA32 Intelligent Reclocking High Performance HD-SDI/SD-SDI Distribution Amplifiers snellgroup.com IQSDA30/IQSDA32 www.snellgroup.com Information and Notices Information
More informationQuick Setup Guide for IntelliAg Model NTA
STEP 3: Auto Configuration (identifies sensors connected to each module) Auto config is performed at the factory, but may need to be done in the field as changes are made to the system or if options are
More informationSingle Axis Position Controller
SERIES P9511 Single Axis Position Controller Compact Construction Simple Go-to operation Integrated Relay Output Integrated Mains Power Supply ELEKTRO-TRADING sp. Z o.o. 44-109 Gliwice, ul. Mechaników
More informationT2210HD/T2210HDA 21.5 Wide-Screen LCD Monitor User Manual
T2210HD/T2210HDA 21.5 Wide-Screen LCD Monitor User Manual Table of Contents Package contents...3 Installation...4 To connect the monitor to your PC... 4 Adjusting your monitor...5 Functions of the buttons
More informationInserting the batteries. Basic settings of the remote control
Inserting the batteries Procedure prior to first use or when changing batteries Remove the back plate to expose the battery tray. Insert 2 x AA 1.5V alkaline batteries. Ensure the polarity of the batteries
More informationHow to Optimize Ad-Detective
How to Optimize Ad-Detective Ad-Detective technology is based upon black level detection. There are several important criteria to consider: 1. Does the video have black frames to detect? Are there any
More informationOPERATING MANUAL. including
OPERATING MANUAL including & If a portable or temporary three phase mains supply is used to power this desk, we recommend that the desk mains plug is removed before connecting or disconnecting the supply.
More informationAmerican DJ. Show Designer. Software Revision 2.08
American DJ Show Designer Software Revision 2.08 American DJ 4295 Charter Street Los Angeles, CA 90058 USA E-mail: support@ameriandj.com Web: www.americandj.com OVERVIEW Show Designer is a new lighting
More informationUsers Manual Firmware 1.06 October 12, 2016
Users Manual Firmware 1.06 October 12, 2016 Proton Switcher Control Surface is a trademark of JLCooper Electronics. All other brand names are the property of their respective owners. Proton Switcher Control
More informationStepSequencer64 J74 Page 1. J74 StepSequencer64. A tool for creative sequence programming in Ableton Live. User Manual
StepSequencer64 J74 Page 1 J74 StepSequencer64 A tool for creative sequence programming in Ableton Live User Manual StepSequencer64 J74 Page 2 How to Install the J74 StepSequencer64 devices J74 StepSequencer64
More information12months. on-site warranty. DZE ELECTRONIC PRESSURE SWITCH for detection of overload per EN 81 2 featuring two adjustable switching points
BUCHER PRODUCTS AVAILABLE FROM HYDRATEC DZE ELECTRONIC PRESSURE SWITCH for detection of overload per EN 81 2 featuring two adjustable switching points 12months on-site warranty All our work comes with
More informationQuick Setup Guide for IntelliAg Model CTA
STEP 3: Auto Configuration (identifies sensors connected to each module) Auto config is performed at the factory, but may need to be done in the field as changes are made to the system or if options are
More informationUser s Manual Rev. A
GEMO Ladder Editor V2.1 User s Manual Rev. A All information subject to 1/96 http://www.gemo.com.tr CONTENT 1 Introduction... 6 2 What s New... 7 2.1 What s new in Ver 2.1... 7 2.2 Abbreviation... 8 3
More informationSXT SXGA TFT NEMA 4/12 Flat Panel Monitor. User s Guide
SXT2010 20.1 SXGA TFT NEMA 4/12 Flat Panel Monitor User s Guide 302010(A) (was document no. 920A0007 version 1.0), revised 12/98 Viewtronix Viewtronix reserves the right to make changes in specifications
More informationDCD-24 Word Clock Distributor
DCD-24 Word Clock Distributor Owner s manual Version 1.00 October 2018 All materials herein Brainstorm Electronics, Inc. Brainstorm Electronics reserves the right to change or modify the contents of this
More information(Skip to step 11 if you are already familiar with connecting to the Tribot)
LEGO MINDSTORMS NXT Lab 5 Remember back in Lab 2 when the Tribot was commanded to drive in a specific pattern that had the shape of a bow tie? Specific commands were passed to the motors to command how
More informationTransmitter Interface Program
Transmitter Interface Program Operational Manual Version 3.0.4 1 Overview The transmitter interface software allows you to adjust configuration settings of your Max solid state transmitters. The following
More informationSPA MICROPROCESSOR SPEEDOMETER INSTALLATION AND OPERATING MANUAL PAGE 2...INSTRUMENT FEATURES PAGE 3...OPERATING INSTRUCTIONS PAGE 3...
SPA MICROPROCESSOR SPEEDOMETER INSTALLATION AND OPERATING MANUAL PAGE 2...INSTRUMENT FEATURES PAGE 3...OPERATING INSTRUCTIONS PAGE 3...MENU SYSTEM PAGE 7...INSTALLATION DIAGRAMS PAGE 10...INSTALLATION
More informationGEMO Ladder Editor V2.2. User s Manual Rev. A. All information subject to change without notice
GEMO Ladder Editor V2.2 User s Manual Rev. A 1/99 CONTENT 1 Introduction...6 2 What s New...7 2.1 What s new in Ver 2.2 Rev A...7 2.2 What s new in Ver 2.1 Rev A...7 2.3 Abbreviation...8 3 Device Input
More informationSTX Stairs lighting controller.
Stairs lighting controller STX-1795 The STX-1795 controller serves for a dynamic control of the lighting of stairs. The lighting is switched on for consecutive steps, upwards or downwards, depending on
More informationMarks and Grades Project
Marks and Grades Project This project uses the HCS12 to allow for user input of class grades to determine the letter grade and overall GPA for all classes. Interface: The left-most DIP switch (SW1) is
More informationASSEMBLY AND CALIBRATION
CineMax Kit ASSEMBLY AND CALIBRATION www.cineversum.com Ref: T9003000 Rev: 01 Part. No.: R599766 Changes CineVERSUM provides this manual as is without warranty of any kind, either expressed or implied,
More informationDP Tuner 80 Remote Control Software User Manual. Version:08 Issue Date:May 10, 2018
DP Tuner 80 Remote Control Software User Manual Version:08 Issue Date:May 10, 2018 Copyright Information Copyrights Lumens Digital Optics Inc. All rights reserved. Lumens is a registered trademark of Lumens
More informationApplication Note 11 - Totalization
Application Note 11 - Totalization Using the TrendView Recorders for Totalization The totalization function is normally associated with flow monitoring applications, where the input to the recorder would
More informationCM-T10-PRO and PRO-E. Wireless Control for ColorMaker Series LED Fixtures with ColorRoll Technology User s Manual
CM-T10-PRO and PRO-E Wireless Control for ColorMaker Series LED Fixtures with ColorRoll Technology User s Manual Introduction CM-T10-PRO and CM-T10-PRO-E (Enhanced) This manual covers both the CM-T10-PRO
More informationTable of Contents. 2 Select camera-lens configuration Select camera and lens type Listbox: Select source image... 8
Table of Contents 1 Starting the program 3 1.1 Installation of the program.......................... 3 1.2 Starting the program.............................. 3 1.3 Control button: Load source image......................
More informationTebis application software
Tebis application software Input products / ON / OFF output / RF dimmer Electrical / Mechanical characteristics: see product user manual Product reference Product designation TP device RF device WYC42xQ
More informationSetup Guide. Konvision monitors. Rev. 1.0
Setup Guide Konvision monitors Rev. 1.0 Introduction CalMAN Display Calibration Software can automatically create multiple optimized calibration 3D LUTs for the entire line of Konvision monitors, with
More informationRELEASE NOTES. Introduction. Supported Devices. Mackie Master Fader App V4.5.1 October 2016
RELEASE NOTES Mackie Master Fader App V4.5.1 October 2016 Introduction These release notes describe changes and upgrades to the Mackie Master Fader app and DL Series mixer firmware since Version 4.5. New
More informationWorking with CSWin32 Software
Working with CSWin32 Software CSWin32 provides a PC interface for Coiltek s ultrasonic control products. The software expands the palette of control features of the CS-5000 and CS-6100 series controls;
More informationTroubleshooting CS800/LC900 Bikes
Troubleshooting CS800/LC900 Bikes CS800/900LC Bike Troubleshooting Entering the Maintenance Mode 15 Touch Screen: The Maintenance Mode is designed to help the tech determine certain faults in the upper
More informationOPERATING GUIDE. M-Vision Cine 3D series. High Brightness Digital Video Projector 16:9 widescreen display. Rev A August A
OPERATING GUIDE M-Vision Cine 3D series High Brightness Digital Video Projector 16:9 widescreen display 112-022A Digital Projection M-Vision Cine 3D series CONTENTS Operating Guide CONTENTS About this
More informationPRODUCT MANUAL LUMENTO X3 LED. LED Controller ZN1DI-RGBX3. Program Version: 1.0 Manual Edition: a
PRODUCT MANUAL LUMENTO X3 LED LED Controller ZN1DI-RGBX3 Program Version: 1.0 Manual Edition: a INDEX 1. Introduction... 3 1.1. LUMENTO X3... 3 1.2. Installation... 4 2. ETS Parameterization... 7 2.1.
More informationQUADRANT DVB-T Modulator USER GUIDE. Quadrant DVB A N T E N N A I R. Copyright 2012 Antennair Limited, Neo House, Shaw Road, OLDHAM OL1 4AW. Issue 1.
QUADRANT DVB-T Modulator USER GUIDE Quadrant DVB A N T E N N A I R Copyright 2012 Antennair Limited, Neo House, Shaw Road, OLDHAM OL1 4AW Issue 1.1 This user guide contains basic instructions for installation
More informationThe DataView PowerPad III Control Panel
Setting Up a Recording Session in the DataView PowerPad III Control Panel By Mike Van Dunk The DataView PowerPad III Control Panel is designed for working with AEMC PowerPad III Power Quality Analyzers,
More informationPacket Voice Impairment Test (PVIT) on the Sage 930A-L3, 930i, and 935AT
Packet Voice Impairment Test (PVIT) on the Sage 930A-L3, 930i, and 935AT The Sage Packet Voice Impairment Test (PVIT) provides detailed diagnostic information about events that impact voice clarity over
More informationGPS Rally Computer. Copyright 2017 MSYapps. All rights reserved. Manual for version Page 1
GPS Rally Computer Copyright 2017 MSYapps. All rights reserved. Manual for version 5.0.6+. Page 1 Introduction The GPS Rally Computer is an application for Apple ios devices, including iphones and ipads,
More informationSetup. Connecting to a DMX Interface
User Guide V0.2 Setup 3 Connecting to a DMX Interface 3 Creating a Project 4 Adding Fixtures 5 Addressing your Fixtures 5 Changing the order of fixtures 5 Controlling with the Faders 6 Setting Pan/Tilt
More informationVideo Effects Processor - VSL 201
Video Effects Processor - VSL 201 Please read these instructions before use Video Solutions Ltd 109 Cranham Drive Worcester WR4 9LZ www.videosolutions.ltd.uk Version 120602 Video Effects Processor - VSL
More informationChapter 23 Dimmer monitoring
Chapter 23 Dimmer monitoring ETC consoles may be connected to ETC Sensor dimming systems via the ETCLink communication protocol. In this configuration, the console operates a dimmer monitoring system that
More informationSample BD Tech Concepts LLC
XYZ Corp. Fry Controller FC-1234 Operating Specification Copyright 2014 Brian Dunn BD Tech Concepts LLC Contents Last Modified: 00/00/0000 Introduction 2 Interface 3 Idle 5 Cooking Cycle 5 Displaying and
More informationViewing Set-Top Box Data
Device View, page 1 Alerts, page 3 Device Properties, page 3 Quick Actions, page 3 View Log Entries, page 4 Monitor STB Connectivity, page 5 Device View Note While every possible effort has been made to
More informationINFORMATION TO USER CAUTION RISK OF ELECTRIC SHOCK, DO NOT OPEN
INFORMATION TO USER CAUTION RISK OF ELECTRIC SHOCK, DO NOT OPEN! CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
More informationSetup Guide. Dolby PRM Rev. 1.1
Setup Guide Dolby PRM-4200 Rev. 1.1 Introduction CalMAN Required Software Version CalMAN Display Calibration Software can automatically create an optimized 3D calibration LUT for the Dolby PRM-4200 monitor.
More informationEAN-Performance and Latency
EAN-Performance and Latency PN: EAN-Performance-and-Latency 6/4/2018 SightLine Applications, Inc. Contact: Web: sightlineapplications.com Sales: sales@sightlineapplications.com Support: support@sightlineapplications.com
More informationLaboratory Exercise 7
Laboratory Exercise 7 Finite State Machines This is an exercise in using finite state machines. Part I We wish to implement a finite state machine (FSM) that recognizes two specific sequences of applied
More informationimso-104 Manual Revised August 5, 2011
imso-104 Manual Revised August 5, 2011 Section 1 Getting Started SAFETY 1.10 Quickstart Guide 1.20 SAFETY 1.30 Compatibility 1.31 Hardware 1.32 Software Section 2 How it works 2.10 Menus 2.20 Analog Channel
More informationBER MEASUREMENT IN THE NOISY CHANNEL
BER MEASUREMENT IN THE NOISY CHANNEL PREPARATION... 2 overview... 2 the basic system... 3 a more detailed description... 4 theoretical predictions... 5 EXPERIMENT... 6 the ERROR COUNTING UTILITIES module...
More informationA summary of all menu lines available in self-diagnostic mode is shown below.
1057-03 rev A 10/08/02 Page 9/33 4. CLUSTER DIAGNOSTICS 4.1. Test at Turn On When ignition voltage is first applied to the cluster, all the tell-tales, except turn signals, turn on for 2 seconds, then,
More informationCar-Solutions.com. Car Video Interface for. Mercedes-Benz C-Class (W204) 2012 and New E-Class 2012 User Manual. Last updated :
Last updated : 2012.03.29 Car Video Interface for Mercedes-Benz C-Class (W204) 2012 and New E-Class 2012 User Manual support@car-solutions.com Contents 1. Before installation 1.1 Main specification 3 1.2
More informationUSB Mini Spectrum Analyzer User Manual TSA Program for PC TSA4G1 TSA6G1 TSA8G1
USB Mini Spectrum Analyzer User Manual TSA Program for PC TSA4G1 TSA6G1 TSA8G1 Triarchy Technologies Corp. Page 1 of 17 USB Mini Spectrum Analyzer User Manual Copyright Notice Copyright 2013 Triarchy Technologies,
More informationBLOCK OCCUPANCY DETECTOR
BLOCK OCCUPANCY DETECTOR This Block Occupancy Detector recognises the current drawn by moving trains within a block, and can operate a number of built-in programs in response. When used with DC systems,
More informationBLUNIK II ACCESSORIES SPORT DRIVE SPORT CALCULATOR... 49
USER GUIDE 12/2016 2 INDEX DESCRIPTION of BLUNIK II...6 DESCRIPTION of parameters...7 ADJUSTMENT OF PARAMETERS...7 Parameter: CLOCK SYNCHRO...8 Parameter: TIRES...9 Parameter: CALIBRATION... 10 Calibration
More informationKNOBS. REPEATS Controls the feedback amount for the heads that have their feedback enabled. ECHO LEVEL
QUICK START GUIDE KNOBS Controls the delay time at head 4. Heads 1-3 subdivide proportionally according to the setting. Delay time ranges vary by selected setting. half: 400ms - 4s normal: 200ms - 2s double:
More informationES-450J2 Universal 2 Channel Jog/Shuttle Remote
ES-450J2 Universal 2 Channel Jog/Shuttle Remote Users Manual ES-450, ES-450J and ES-450J2 are trademarks of JLCooper Electronics. All other brand names are the property of their respective owners. ES-450J2
More informationFR-8 and FR-16 Remote Control Operating Manual
FR-8 and FR-16 Remote Control Operating Manual Introduction The FR-8 and FR-16 are Ethernet-based remote control devices for Ashly Ethernet compatible products with DSP capabilities, including the Ashly
More informationEncoders - Measuring rotation of a wheel or
Encoders - Measuring rotation of a wheel or other shaft Encoders are devices for measuring the rotation of a spinning shaft. Encoders are typically used to measure the distance a wheel has turned which
More informationUser s Manual. Network Board. Model No. WJ-HDB502
Network Board User s Manual Model No. WJ-HDB502 Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. CONTENTS Introduction...
More informationScanning and Joystick Selection
CHAPTER_.A 4/8/00 9:4 PM Page 1 Chapter Six Scanning and Joystick Selection CHAPTER_.A 4/8/00 9:4 PM Page 2 Scanning and Joystick Selection Introduction If you do not intend to use the DigiCom in Scanning
More informationPrecision DeEsser Users Guide
Precision DeEsser Users Guide Metric Halo $Revision: 1670 $ Publication date $Date: 2012-05-01 13:50:00-0400 (Tue, 01 May 2012) $ Copyright 2012 Metric Halo. MH Production Bundle, ChannelStrip 3, Character,
More informationVideo to DVI 1080p Scaler Box - ID# 796
Video to DVI 1080p Scaler Box - ID# 796 Operation Manual Introduction Video to DVI 1080p Scaler Box is an upgraded design to convert Standard Definition Composite Video (CV) and S-Video (SV) signals to
More informationGreenParking. Commissioning guide. GreenParking
GreenParking GreenParking Page Table of Contents Introduction....4. GreenParking...4. Working principle...4.3 Intended use...4.4 About this commissioning guide...4.5 Warnings.............................................................
More informationTRIMBLE GPS / 10MHz REFERENCE MONITOR DISPLAY V January 2015
TRIMBLE GPS / 10MHz REFERENCE MONITOR DISPLAY V1.2-1.4 January 2015 A display and command module for the Trimble Thunderbolt GPS with 10MHz reference oscillator. by Hubbatech Software Revision Notes: 1.2-2014
More informationNMS ETA TM Stereo Advanced Digital TV Set-top Box
Digital TV HD Set-top Box STB2-T2 NMS ETA TM Stereo Advanced Digital TV Set-top Box User Guide CONTENTS Safety Information... 3 Introduction... 4 Set-top Box Front Panel... 4 Set-top Box Back Panel...
More informationEdit Menu. To Change a Parameter Place the cursor below the parameter field. Rotate the Data Entry Control to change the parameter value.
The Edit Menu contains four layers of preset parameters that you can modify and then save as preset information in one of the user preset locations. There are four instrument layers in the Edit menu. See
More informationDRAFT RELEASE FOR BETA EVALUATION ONLY
IPM-16 In-Picture Audio Metering User Manual DRAFT RELEASE FOR BETA EVALUATION ONLY Ver 0.2 April 2013 1 Contents Introduction...3 In Picture Audio Meter Displays...4 Installation...7 External Audio Board
More informationUser manual. EVBIKE - LCD display C961
User manual EVBIKE - LCD display C961 CONTENS: 1. INSTALATION 2. BASE SETTINGS 3. ADVANCE SETTINGS 4. ERROR ROR CODES Thank you for purchasing EVBIKE product and we hope that you will become a happy user.
More informationKNX Technical Reference Manual Busch-EnergyControl
0073-1-7703 Rev. 02 05.2011 KNX Technical Reference Manual Busch-EnergyControl 6762-500 Efficiency with a future Less consumption and fewer costs pay off for people and the environment. You only need the
More information14/09/98 Martin Casemanual (Version 6.21) The effect generator PRESS : $, 7
5.1 In general To make programming a lot easier, and to save lots of time, the controller is equipped with an effect generator. Now it is possible to launch all kinds of effects on every fixture channel
More informationVERSION 2.A 10/21/1999. Lightronics Inc. 509 Central Drive, Virginia Beach, VA TEL
7/ 0(025< /,*+7,1*&21752/ &2162/( 2:1(56Ã0$18$/ VERSION 2.A 10/21/1999 Contents DESCRIPTION OF CONTROLS 3 OPERATION 4 USING THE MENU SYSTEM 5 MENU FUNCTIONS 5 RECORDING SCENES 7 USING SCENES 8 RECORDING
More informationUSER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.0
by USER MANUAL FOR THE ANALOGIC GAUGE FIRMWARE VERSION 1.0 www.aeroforcetech.com Made in the USA! WARNING Vehicle operator should focus primary attention to the road while using the Interceptor. The information
More informationThe Kaffeine Handbook. Jürgen Kofler Christophe Thommeret Mauro Carvalho Chehab
Jürgen Kofler Christophe Thommeret Mauro Carvalho Chehab 2 Contents 1 Kaffeine Player 5 1.1 The Start Window...................................... 5 1.2 Play a File..........................................
More informationSpinner- an exercise in UI development. Spin a record Clicking
- an exercise in UI development. I was asked to make an on-screen version of a rotating disk for scratching effects. Here's what I came up with, with some explanation of the process I went through in designing
More informationUSER MANUAL USER MANUAL. VIO 4K Ref. V701 PROGRAMMER S GU.
USER MANUAL VIO 4K Ref. V701 1 Table of Contents 1 Introduction... 6 1.1 Why use the VIO 4K?... 6 1.2 VIO 4K at a glance... 6 1.3 Key features... 6 1.4 Inputs... 7 1.5 Outputs... 7 1.6 Universal system
More informationOperating Instructions. Room temperature controller with clock
Operating Instructions Room temperature controller with clock 0389.. Table of contents Normal view in the display... 3 Basic operation of the room temperature controller... 3 The individual displays and
More informationDP C18.UART CONTENT CONTENT. Content 1. Normal indication area 6. Button definition 7. Introduction 2. Normal operation 7. Overview drawing 3
CONTENT DP C18.UART CONTENT Content 1 Introduction 2 Overview drawing 3 Specifications 4 Functional overview 5 Normal indication area 6 Button definition 7 Normal operation 7 User set 10 Error code definition
More informationTechnical Description Track-Control
Technical Description Track-Control Uhlenbrock Elektronik GmbH Mercatorstraße 6 46244 Bottrop E-Mail: info@uhlenbrock.de Web: www.uhlenbrock.de TV 1.0. 17.09.2007 Track-Control 1. Overall Operation 1.1
More informationKNX Dimmer RGBW - User Manual
KNX Dimmer RGBW - User Manual Item No.: LC-013-004 1. Product Description With the KNX Dimmer RGBW it is possible to control of RGBW, WW-CW LED or 4 independent channels with integrated KNX BCU. Simple
More informationThe Measurement Tools and What They Do
2 The Measurement Tools The Measurement Tools and What They Do JITTERWIZARD The JitterWizard is a unique capability of the JitterPro package that performs the requisite scope setup chores while simplifying
More informationGPS Rally Computer. Copyright 2017 MSYapps. All rights reserved. Manual for version 3.3.
GPS Rally Computer Copyright 2017 MSYapps. All rights reserved. Manual for version 3.3. Introduction The GPS Rally Computer is an application for Apple ios devices, including iphones and ipads, that perform
More informationXDFilt 1r0 July 23, XDFilt 1r0. Instructions. Copyright 2007, Steven A. Harlow 1
XDFilt 1r0 Instructions Copyright 2007, Steven A. Harlow 1 Table of Contents 1 INTRODUCTION...3 2 INSTALLATION...3 3 CUT TO THE DEMO...3 3.1 MAIN DEMO...3 3.2 GRAPHICAL FILTER DEMO...6 4 OPERATING CONTROLS
More informationPS User Guide Series Seismic-Data Display
PS User Guide Series 2015 Seismic-Data Display Prepared By Choon B. Park, Ph.D. January 2015 Table of Contents Page 1. File 2 2. Data 2 2.1 Resample 3 3. Edit 4 3.1 Export Data 4 3.2 Cut/Append Records
More information