3M Distribution Box (DDB)

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "3M Distribution Box (DDB)"

Transcription

1 3M Distribution Box (DDB) Merged Copper and Fiber Pole/Post Mount Enclosure Installation Instructions November A

2 2 November A Contents 1.0 General 2.0 Enclosure installation 3.0 Enclosure external ground 4.0 Fiber cable installation 5.0 Copper cable installation 6.0 Terminating wires on back of 3M Quick Connect System (QCS) 2810B Block 7.0 Terminating DSLAM copper cable onto the back of the 10-pair block 1.0 General 1.1 These instructions provide the information necessary for the installation of the 3M Distribution Box DDB. The enclosure is equipped with a 100 pair of the 3M Quick Connect System (QCS) 2810 blocks plus a 12-fiber SC/APC termination/connection frame. The enclosure can be direct mounted on a pole or post and does not require a mounting frame. 2.0 Closure installation 2.1 Mounting holes Verify the mounting surface can accept a 4 ¼" width mounting hole spacing. Open the enclosure. Locate the upper mounting holes approximately 1" below the top of the closure. Temporarily support closure to mounting surface. Center on mounting surface. When plumb, mark the top two mounting hole locations. Secure to mounting surface with screws that include flat washers on top and bottom. Upper mounting hole locations The 4 ¼" mounting hole spacing requires a minimum of a 6" wide flat post or a typical telephone pole. Mounting the closure and accessories are covered in these instructions. 1.2 Tools required for installation: a. Standard hand tools b. Drill for pole or post mounting c. Screws and flat washers 1.3 Image and cable count example Lower mounting hole and cable anchoring/grounding detail 9 ½" W x 25" H x 5" D

3 A November Enclosure external ground 3.1 Select bottom port for external ground entrance. 4.3 Loop buffer tube(s) one time around fiber tray assembly using retaining clips to manage. 3.2 Punch through plastic port plug using screwdriver or equivalent. 3.3 Route #6 external ground wire from source into port to ground wire lug. 3.4 Secure ground wire to bond bar per company practice. 4.0 Fiber cable installation 4.1 Prepare incoming fiber feeder cable by removing 90" (2286 mm) of outer sheath. 4.2 Punch through plastic port plug using screwdriver or equivalent and insert prepped cable with exposed buffer(s) through plastic port plug opening. Note: If using shielded fiber cable, install supplied 3M Scotchlok Shield Bond Connector 4460D between hose clamp and CSM retainer per your company practice. Use grounding location next to cable anchor bracket to secure ground wire per your company practice. Secure cable to anchor bracket using supplied hose clamp (sheath) and CSM retainer. 4.4 Remove 30" (762 mm) of protective buffer tube to expose 250 µm fiber(s). 4.5 Install buffer tube onto tray as shown, locking tray clip and installing cable tie to anchor buffer tube in place. 4.6 Install connectorized pigtails into adapters in orientation as shown (number and type may vary, 4 SC/APC connectors shown).

4 4 November A 4.7 Install 900 µm pigtails onto tray as shown, opposite the incoming side of the 250 µm fibers, using locking tray clip to secure the fibers Store slack fiber(s) (up to 3.0 mm jacket) of DSLAM cable, looping around fiber tray assembly using retaining clips as necessary Plug connectors into corresponding adapter ports above tray to complete the connection. 5.0 Copper cable installation 5.1 Remove the threaded ring and components from the two large entry ports. 5.2 Recycle solid metal plates. 5.3 Slide threaded ring, a sealing washer, rubber grommet, and the other sealing washer (in that order) onto cable to be prepped. 4.8 Group fibers together using wire ties or loosely secured cable ties to manage bundle. DO NOT OVER TIGHTEN. 4.9 Complete splices per company practice and store slack in appropriate area of tray Prepare DSLAM fiber cable grommet by trimming to the correct size opening for the sheath cable If connectors are preterminated on the DSLAM cable, insert them carefully through the grommet opening one at a time If using shielded cable, install supplied 3M Scotchlok Shield Bond Connector 4460D located between the hose clamp and CSM retainer per company practice Use grounding location next to cable anchor bracket to secure ground wire per company practice. If desired, use thread cutting 8-32 screw to secure ground wire in alternate location. Screw not supplied. 5.4 Prepare incoming cable by removing sheath to expose conductors. 5.5 If using shielded cable, install 3M Shield Bond 4460 connector per company practice. 5.6 Scuff perimeter of cable and wrap with Scotch Linerless Rubber Splicing Tape 130C in scuffed location to build up diameter for a slight interference fit of rubber grommet. 5.7 Slide port entry components into place on the taped area. 5.8 Tighten threaded ring onto port entry collet to compress rubber grommet onto cable Secure cable to anchor bracket using supplied hose clamp (sheath) and Central Strength Member (CSM) retainer, if a CSM is present Removal of the bottom the 3M Quick Connect System (QCS) 2814 block may be necessary to access the CSM retainer bolt. If removed, reinstall after securing the CSM.

5 A November Use grounding location next to cable anchor bracket to secure ground wire per company practice. 7.0 Terminating DSLAM copper cable onto the back of the 10-pair block 7.1 Remove blocks and set aside. 7.2 Rotate one block and reinsert on frame. 7.3 Separate and route each 10 pair to the corresponding block. 6.0 Terminating wires on back of 3M Quick Connect System (QCS) 2810B Block 6.1 Locate metal bracket tab, insert flat screwdriver and push bracket tab outward. 6.2 Raise block slightly, once released from the bracket, and release tab on opposite side. 6.3 Lift off block once both sides are released from bracket. 7.4 Route each cable pair over the respective pair cap and place in cap slots temporarily. 7.5 Keep Ring right and Tip left as block will roll over in place. 6.4 Roll block over and temporarily seat face down on the metal bracket tabs. 6.5 Lift corresponding orange caps, insert house wires and snap cap closed to terminate. 7.6 Cut conductors to length and insert in orange cap. Note: Wires will enter cap from top of block when terminating on back. 6.6 Terminate wires with regard to tip and ring when rolled back to reinstall. 6.7 Roll block back over and reseat on metal bracket tabs - stencil tab side up. 6.8 Apply downward pressure until block snaps in place on metal bracket tab.

6 7.7 Snap cap into place until audible click to terminate cable conductor into the block Remove sheath, mark groups and bond per company practice Route conductors up the left side of the frame Route the respective 10-pairs to their appropriate 10-pair block Terminate the 100-pair cable onto the front of the 10-pair blocks. 7.8 Complete all cable conductors on all blocks. This architecture allows for the existing cable pair to be routed into the DSLAM and out of the DSLAM in their respective cable counts. 7.9 Snap all blocks back into their respective pair count on the 100-pair frame Place the copper cable from the left cable port in the enclosure to the existing cable splice. 3M, Scotch, and Scotchlok are trademarks of 3M Company. Important Notice All statements, technical information, and recommendations related to 3M s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any direct, indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. Communication Markets Division 6801 River Place Blvd. Austin, TX Phone Web Please recycle. Printed in USA 3M All rights reserved A

3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR 3M Cable Addition Kit 2181-XL and 2181-XL/FR

3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR 3M Cable Addition Kit 2181-XL and 2181-XL/FR 3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR 3M Cable Addition Kit 2181-XL and 2181-XL/FR Instructions July 2010 3 1.0 Contents 1.0 General...3 2.0 Kit Contents...3 3.0 Cable Preparation...4 4.0

More information

3M Fiber Optic Splice Closure 2178-XSB/XSB-FR & 2178-XLB/XLB-FR 3M Cable Addition Kit 2181-XB/XB-FR

3M Fiber Optic Splice Closure 2178-XSB/XSB-FR & 2178-XLB/XLB-FR 3M Cable Addition Kit 2181-XB/XB-FR 3M Fiber Optic Splice Closure 2178-XSB/XSB-FR & 2178-XLB/XLB-FR 3M Cable Addition Kit 2181-XB/XB-FR Instructions July 2010 78-8135-0094-5-K 3 1.0 General 1.1 3M Fiber Optic Splice Closure 2178-XSB The

More information

SLiC Fiber Aerial Closure System

SLiC Fiber Aerial Closure System 3 SLiC Fiber Aerial Closure System SLFC 533-SP SLFC 533-TS SLFC 733-SP Instructions May 2005 78-8135-4502-3-B N C H E S R A N G E M IL L IM E T E R S.4 10.6.8 A B C 15 20 I 1.0 Kit Contents Note: Examine

More information

3M Better Buried Compound Compression Closure System

3M Better Buried Compound Compression Closure System 3M Better Buried Compound Compression Closure System Instructions March 2016 78-0015-2948-2-A Contents: 1.0 General...3 2.0 Kit Contents...3 3.0 Closure Selection Guide...4 4.0 LHS End Cap Installation...5

More information

2178-L/S Series Fiber Optic Splice Case with Gasket

2178-L/S Series Fiber Optic Splice Case with Gasket 2178-L/S Series Fiber Optic Splice Case with Gasket Instructions for: 2178-S Splice Case 2178-LS Splice Case 2178-LL Splice Case 2181-LS Cable Addition Kit May 1997 34-7041-9949-5-A 1 Table of Contents

More information

3M Fiber Optic Wall Mount Enclosure 8430 Series

3M Fiber Optic Wall Mount Enclosure 8430 Series 3M Fiber Optic Wall Mount Enclosure 8430 Series Installation Instructions January 2014 3 78-0013-9429-1-A Table of Contents 1.0 Description...3 2.0 Parts...4 3.0 Assembly...4 4.0 Mounting the Enclosure...6

More information

3M Fiber Optic Splice Tray 2527 with 3M PLC Optical Splitter

3M Fiber Optic Splice Tray 2527 with 3M PLC Optical Splitter 3M Fiber Optic Splice Tray 2527 with 3M PLC Optical Splitter Instructions January 2010 3 1.0 General 1.1 The 3M Fiber Optic Splice Tray 2527 with 3M PLC Optical Splitter(s) protects, organizes and stores

More information

3M Cross-Connect Cabinets 4220SVB, 4220SVC and 4220SVE 3M Junction Box (JBOX)

3M Cross-Connect Cabinets 4220SVB, 4220SVC and 4220SVE 3M Junction Box (JBOX) 3M Cross-Connect Cabinets 4220SVB, 4220SVC and 4220SVE 3M Junction Box (JBOX) In-cabinet and Outdoor AC Power Junction Box (JBOX) for 3M Cross-Connect Cabinets with DSLAM apparatus cases installed Instructions

More information

2179-CD Series Fiber Optic Splice Closure. Installation Instructions

2179-CD Series Fiber Optic Splice Closure. Installation Instructions 2179-CD Series Fiber Optic Splice Closure Installation Instructions 1.0 Product Introduction The new 3M TM 2179-CD Series Fiber Optic Splice Closure can be used in buried, underground, aerial, and pedestal

More information

3M Cross-Connect Cabinets 4220SVB, 4220SVC and 4220SVE Skirt and Stabilizers

3M Cross-Connect Cabinets 4220SVB, 4220SVC and 4220SVE Skirt and Stabilizers 3M Cross-Connect Cabinets 4220SVB, 4220SVC and 4220SVE Skirt and Stabilizers Rear skirt and stabilizers to cover and protect DSLAM apparatus cases mounted directly on 3M Pad or Stake Mount Cabinets Instructions

More information

High Density Block BRCP. HD BRCP- 128/192/256 pair. Installation Instructions

High Density Block BRCP. HD BRCP- 128/192/256 pair. Installation Instructions High Density Block BRCP HD BRCP- 128/192/256 pair Installation Instructions Product Introduction The BRCP block is the latest generation of MDF terminal blocks developed by 3M, specifically designed for

More information

3M Locator Plate N

3M Locator Plate N M Locator Plate 44-107N Instructions for the assembly of.100 x.100 preassembled socket connectors 1.0 General The M Locator Plate 44-107N is designed to aid in the assembly of the preassembled socket connector

More information

2178 Fiber Optic Splice Case and 2181 Cable Addition Kit

2178 Fiber Optic Splice Case and 2181 Cable Addition Kit 2178 Fiber Optic Splice Case and 2181 Cable Addition Kit Instructions January 1994 Issue 1, 34-7029-6387-6 1 2 Contents: 1.0 General... 4 2.0 Specifications... 4 3.0 Kit Contents... 5 SECTION 1: 2178 Splice

More information

3M Fiber Optic Splice Closure 2178-L/S Series with Gasket

3M Fiber Optic Splice Closure 2178-L/S Series with Gasket 3M Fiber Optic Splice Closure 2178-L/S Series with Gasket Instructions for: 3M Fiber Optic Splice Closures 2178-L/S Series 3M Flame Retardant Fiber Optic Splice Closures 2178-L/S/FR 3M Cable Addition Kit

More information

3 Closure preparation 3.1 Work-stand 3.2. Opening FIST-GCOG2-Dx Preparing drop cable with micro-tubes

3 Closure preparation 3.1 Work-stand 3.2. Opening FIST-GCOG2-Dx Preparing drop cable with micro-tubes FIST-GCOG2-Dx24 I N S T A L L A T I O N I N S T R U C T I O N FTTH closure for micro-tubes and micro-cables Content 1 Introduction 2 Kit content 3 Closure preparation 3.1 Work-stand 3.2. Opening FIST-GCOG2-Dx24

More information

FIST-MB2-S. FIST Medium Box for Cable Splicing Only. 4 Cable installation. 1 Introduction. Contents. 2 General. 5. Fiber routing to individual trays

FIST-MB2-S. FIST Medium Box for Cable Splicing Only. 4 Cable installation. 1 Introduction. Contents. 2 General. 5. Fiber routing to individual trays FIST-MB2-S I N S T A L L A T I O N I N S T R U C T I O N FIST Medium Box for Cable Splicing Only Contents 1 Introduction 1.1 Product description 2 General 2.1 Tools 2.2 Kit contents 3 Installation and

More information

3M Fiber Closures BPEO

3M Fiber Closures BPEO 3M Fiber Closures BPEO 2 3M Fiber Closures BPEO The 3M Fiber Closures BPEO are designed with flexibility in application in mind. With a range of sizes, they can be deployed above grade (pole, facade) or

More information

FOSC-450D. Fiber Optic Splice Closure. 1 Introduction. Content. 5 Cable termination. 6 Fiber routing. 2 General. 7 Installation of the gel block

FOSC-450D. Fiber Optic Splice Closure. 1 Introduction. Content. 5 Cable termination. 6 Fiber routing. 2 General. 7 Installation of the gel block FOSC-450D I N S T A L L A T I O N I N S T R U C T I O N Fiber Optic Splice Closure Content 1 Introduction 2 General 2.1 Kit content 2.2 Tools 2.3 Accessories 2.4 Capacity 3 Preparation of the closure 4

More information

K & B Flame Retardant Building Riser Closures

K & B Flame Retardant Building Riser Closures K & B Flame Retardant Building Riser Closures September 1995 Issue 1, 34-7016-7030-8 1. General 1.1 3M Brand K&B Building Riser Closures are designed for use in building riser closets and may be positioned

More information

3M Cold Shrink Splice Kit QS-III 5514A

3M Cold Shrink Splice Kit QS-III 5514A 3M Cold Shrink Splice Kit QS-III 5514A for UniShield, Wire Shielded, Longitudinally Corrugated (LC), and Tape Shielded (Ribbon Shielded) Cable or Transitions to Concentric Neutral (CN)/Jacketed Concentric

More information

3M Scotchcast Flexible Power Cable Splice Kits 82-F Series

3M Scotchcast Flexible Power Cable Splice Kits 82-F Series 3M Scotchcast Flexible Power Cable Splice Kits 82-F Series For use in weather-exposed, direct burial or submerged locations. For making in-line splices on non-shielded portable power cables and cords rated

More information

Cabinet Tools and Accessories Ordering Guide

Cabinet Tools and Accessories Ordering Guide 3 Cabinet Tools and Accessories Ordering Guide 3M Cabinet Tools and Accessories 3M 4320 Block Spare Parts Replacement Cap Kit 100 Tan + 100 Orange 1/cs. 1/cs. 054007-63793 Half-tap, feed through 100 Tan

More information

Cold Shrink Three-Conductor Splice Kit QS-III for use on Armor and Non-Armor Cables Instructions IEEE Std kv Class 250 kv BIL

Cold Shrink Three-Conductor Splice Kit QS-III for use on Armor and Non-Armor Cables Instructions IEEE Std kv Class 250 kv BIL Cold Shrink Three-Conductor Splice Kit QS-III for use on Armor and Non-Armor Cables Instructions IEEE Std. 404 35 kv Class 250 kv BIL Kit Number 5798A-MT Cable Range Requirements Cable Insulation O.D.

More information

3M No Polish Jacketed SC/APC Connector

3M No Polish Jacketed SC/APC Connector Communication Markets Division 3M No Polish Jacketed SC/APC Connector For use with 1.6 to 3.0 mm Jacketed Cable 3M No Polish SC/APC Connector enables fast, on-site termination of 1.6 mm to 3.0 mm jacketed

More information

3M Pressurized Closure System 2-Type 505

3M Pressurized Closure System 2-Type 505 Communication Markets Division 3M Pressurized Closure System 2-Type 505 The 3M Pressurized Closure System 2-Type 505 is a complete, pressuretight, re-enterable closure system for enclosing spliced connections

More information

HSK Mine and Portable Cable Splice

HSK Mine and Portable Cable Splice 8096-4-HSK Mine and Portable Cable Splice Instructions 5 and 8 kv rated cables; Type SHD-GC Size 2/0 4/0 (connector max. length 2 1/2") 8096-4-HSK Mine and Portable Cable Splice 78-8119-6296-4-A 1 1.0

More information

Industrial Loadbreak Elbow

Industrial Loadbreak Elbow Industrial Loadbreak Elbow 200 A 5, 8, and 15 kvclass 5810 Series Installation Instructions 1.0 General The 3M Industrial Loadbreak Elbow connector is a fullyshielded and insulated plug-in termination

More information

Scotch Heavy Duty Vinyl Electrical Tape 22

Scotch Heavy Duty Vinyl Electrical Tape 22 Scotch Heavy Duty Vinyl Electrical Tape 22 Data Sheet July 2015 Description Agency Approvals & Self Certifications Scotch Heavy Duty Vinyl Electrical Tape 22 is a premium grade, 10-mil thick, vinyl insulating

More information

OFDC-B8-72. Outdoor fiber distribution closure. 6 Closing. Content 1 Introduction. 7 Re-entry. 2 Kit content. 3 Closure preparation

OFDC-B8-72. Outdoor fiber distribution closure. 6 Closing. Content 1 Introduction. 7 Re-entry. 2 Kit content. 3 Closure preparation OFDC-B8-72 I N S T A L L A T I O N I N S T R U C T I O N Outdoor fiber distribution closure Content 1 Introduction 2 Kit content 3 Closure preparation 4 Cable preparation 4.1 Feeder cable 4.2 Drop cable

More information

3M Cold Shrink Rubber Splicing Kit 5552

3M Cold Shrink Rubber Splicing Kit 5552 3M Cold Shrink Rubber Splicing Kit 5552 for 5/8 kv Shielded to Shielded or Shielded to Non-Shielded Cables Instructions IEEE Std. No. 404 5 kv Class, 75 kv BIL 8 kv Class, 95 kv BIL! CAUTION Working around

More information

Communication Markets Division. 3M Fiber Closures. Smart design makes your job easier.

Communication Markets Division. 3M Fiber Closures. Smart design makes your job easier. Communication Markets Division 3M Fiber Closures Smart design makes your job easier. 2 Your connections deserve the best protection. No matter the size and configuration of your network, protecting its

More information

2178 L/S Series Fiber Optic Splice Cases and Accessories

2178 L/S Series Fiber Optic Splice Cases and Accessories 2178 L/S Series Fiber Optic Splice Cases and Accessories The 3M 2178 Fiber Optic Splice Case family has always given you great protection for fiber optic connections. Now, the addition of 3M 2178-L/S Series

More information

Cold Shrink Silicone Rubber Termination QT-II

Cold Shrink Silicone Rubber Termination QT-II 3 Cold Shrink Silicone Rubber Termination QT-II Instructions IEEE Std. No. 48-1990 Class 1 Termination 15 Class 110 kv BIL Kit Contents: 1 Hi-K Silicone Rubber Termination 2 Scotch Silicone Rubber Tape

More information

FOSC 400. Ordering Guide For Closures and Accessories. Section I 3. Section II 5. Section III 9. Section IV 11. Section V 15

FOSC 400. Ordering Guide For Closures and Accessories. Section I 3. Section II 5. Section III 9. Section IV 11. Section V 15 FOSC 400 Ordering Guide For Closures and Accessories Section I 3 How to Order FOSC 400 Closures Section II 5 How to Order Accessories for FOSC 400 Closures Section III 9 Other FOSC Fiber Optic Splice Closures

More information

3M Merchandising Catalog. Unrivaled. Product Presence to. Meet Your Merchandising Needs

3M Merchandising Catalog. Unrivaled. Product Presence to. Meet Your Merchandising Needs 3M Merchandising Catalog Unrivaled Product Presence to Meet Your Merchandising Needs 1 Table of Contents Gondolas...3-5 Shelves...6-7 Racks...8-10 Portable Labeler Displays...11-14 Terminals Displays...15-17

More information

3M Cold Shrink QS4 Integrated Splice Kit QS4-15SP-2-4/0

3M Cold Shrink QS4 Integrated Splice Kit QS4-15SP-2-4/0 3M Cold Shrink QS4 Integrated Splice Kit QS4-15SP-2-4/0 for Jacketed Concentric Neutral (JCN), Flat Strap, Tape Shield and Longitudinally Corrugated (LC) Cable Instructions IEEE Std. 404 15 kv Class 150

More information

Fiber Optic Splice Closure GPJ Instruction Manual

Fiber Optic Splice Closure GPJ Instruction Manual Fiber Optic Splice Closure GPJ09-9401 Instruction Manual 1. Brief Introduction GPJ09-9401 type of Fiber Optic Splice Closure is a member in dome series, the main function is to provice direct pass, branch

More information

Built tough for long-term connections

Built tough for long-term connections Communication Markets Division 3M Scotchlok Connectors Built tough for long-term connections 2 3 Durable, insulated connections on the first crimp. Over 50 years ago, 3M introduced the industry s original

More information

Built tough for long-term connections

Built tough for long-term connections Communication Markets Division 3M Scotchlok Connectors Built tough for long-term connections 2 3 Durable, insulated connections on the first crimp. Over 50 years ago, 3M introduced the industry s original

More information

Fiber Cable Preparation, Splicing, and Termination Instructions (CFDP210-EL24 Charlesr Fiber CFDP2 Pedlockr OSP Pedestal)

Fiber Cable Preparation, Splicing, and Termination Instructions (CFDP210-EL24 Charlesr Fiber CFDP2 Pedlockr OSP Pedestal) Equipment Issue 1 First Printing, May 2011 Preparation, Splicing, and Termination Instructions (CFDP210-EL24 Charlesr CFDP2 Pedlockr OSP Pedestal) 1. GENERAL 1.1 Document Purpose. This document provides

More information

TV55. Owner s Manual. Indoor/Outdoor Amplified TV Antenna

TV55. Owner s Manual. Indoor/Outdoor Amplified TV Antenna Owner s Manual Indoor/Outdoor Amplified TV Antenna Safety Precautions Warning! Use extreme caution when installing or removing an outdoor antenna that is located close to overhead wires such as power lines,

More information

Quick Term II. Cold Shrink Silicone Rubber Termination (With High-K Stress Relief) Instruction Sheet. Quick Term II. Silicone Rubber Termination Kits

Quick Term II. Cold Shrink Silicone Rubber Termination (With High-K Stress Relief) Instruction Sheet. Quick Term II. Silicone Rubber Termination Kits Quick Term II Cold Shrink Silicone Rubber Termination (With High-K Stress Relief) Instruction Sheet IEEE Std. No. 48 1990 Class 1 Termination 15 kv Class 110 kv BIL Kit Contents: 3 Hi K Silicone Rubber

More information

LGX Compatible (LSX) Connector Module) User Manual)

LGX Compatible (LSX) Connector Module) User Manual) LGX Compatible (LSX) Connector Module) User Manual) 15948-A LSX Connector Module (72-Position Module Shown) Content Page 1 DESCRIPTION... 3 2 DIMENSIONS AND SPECIFICATIONS... 5 3 INSTALLATION... 6 3.1

More information

Seal Kits for BUDI Enclosures

Seal Kits for BUDI Enclosures Description BUDI is a product range of compact, wall mountable fiber enclosures for indoor and outdoor use. They are specifically designed for fast deployment and easy customer connection. The FIST management

More information

Instructions for Use of Overlap Seam Repair Kit:

Instructions for Use of Overlap Seam Repair Kit: Instructions for Use of Overlap Seam Repair Kit: 3M has assembled a field repair kit to adhesively re-attach delaminated overlap seams on trailers or truck body sidewalls. If the overlap seams were previously

More information

3M Fiber Optic Splice Closure 2178 Family. Flexible Fiber. Management Solutions

3M Fiber Optic Splice Closure 2178 Family. Flexible Fiber. Management Solutions 3M Fiber Optic Splice Closure 2178 Family Flexible Fiber Management Solutions More flexibility for your complex fiber optic network A full line of closures and accessories designed to protect fiber optic

More information

3M MetPak 2-FB Header

3M MetPak 2-FB Header M MetPak 2-FB Header Solder Tail End-to-end stackable Select load capability Monoblockable Shoulder Pin Press Fit End-to-end stackable Early mate late break for hot swapping (press-fit EMLB adjusted by

More information

Fiber Optic Splice Closure GPJ Instruction Manual. [Escribir texto]

Fiber Optic Splice Closure GPJ Instruction Manual. [Escribir texto] Fiber Optic Splice Closure GPJ09-8205 Instruction Manual [Escribir texto] 0 Table of Contents 1. General Introduction 2 2. Specification 2 3. Structure 2 4. Installation instructions. 4 5. Operation procedure.

More information

Flexible Fiber Management Solutions

Flexible Fiber Management Solutions Communication Markets Division 3M Fiber Optic Splice Closure 2178 Family Flexible Fiber Management Solutions More flexibility for your complex fiber optic network A full line of closures and accessories

More information

GENUINE PARTS ! CAUTION

GENUINE PARTS ! CAUTION GENUINE PARTS SATELLITE RADIO INSTALLATION INSTRUCTIONS 1. DESCRIPTION: SATELLITE RADIO SYSTEM 2. PART NUMBERS: XM tuner kit 999U9-NV003 Sirius tuner kit 999U9-NV004 XM antenna kit 999U9-VQ006 Sirius antenna

More information

VHF + UHF Amplified HDTV Antenna Model OA8000 & OA8001 Installation Instructions Reception Frequencies

VHF + UHF Amplified HDTV Antenna Model OA8000 & OA8001 Installation Instructions Reception Frequencies VHF + UHF Amplified HDTV Antenna Model OA8000 & OA8001 Installation Instructions Reception Frequencies VHF: 54-216 MHz UHF: 470-698 MHz FM: 87.9-107.9 MHz Voltage Input: AC110-120V / AC220-240V Working:

More information

FOSC 400 A4 Fiber Optic Splice Closure

FOSC 400 A4 Fiber Optic Splice Closure FOSC 400 A4 Fiber Optic Splice Closure I N S T A L L A T I O N I N S T R U C T I O N 1. General Product Information This installation practice provides instructions for installing Tyco Electronics FOSC

More information

Turret Replacement Instruction Manual

Turret Replacement Instruction Manual Automatic Multi-Satellite TV Antenna Turret Replacement Instruction Manual for models RPSKLGL, RPSKSML, SK-LG00, SK-SM00, & RP-SWM For help, email help@winegard.com or call -800-788-7 568 Raising the Antenna

More information

75 Elliptical Antenna System

75 Elliptical Antenna System Instruction and Assembly Manual 75 Elliptical Antenna System 7291 NW 74th Street Miami, FL 33166 GlobeCast Technical Service: (888) 988-5288 Manufactured By: 2002 Channel Master LLC Printed in U.S.A. 8000915-02

More information

Cable System Installation Guide

Cable System Installation Guide Overview Cable System Installation Guide 5/19/2008 Our recommended approach for the installation of your Circle Graphics Cable Systems on the panels in your market is to install the fixed hardware (namely

More information

Next Generation Frame (NGF) Fiber Combination Block (FCB) User Manual)

Next Generation Frame (NGF) Fiber Combination Block (FCB) User Manual) Next Generation Frame (NGF) Fiber Combination Block (FCB) User Manual) Fiber Combination Block Content Page INTRODUCTION............................................................................. 2 Revision

More information

Water blocking tape. Locator ridge HPA-0486

Water blocking tape. Locator ridge HPA-0486 Table of Contents STANDARD RECOMMENDED PROCEDURE 004-138 ISSUE 1 MARCH 2012 PAGE 1 OF 12 Sheath Removal and Mid-Span Access of Dielectric ALTOS Cable with FastAccess Technology p/n 004-138, Issue 1 1.

More information

Installation Manual SaVi Note Underwater LED Light

Installation Manual SaVi Note Underwater LED Light Installation Manual SaVi Note Underwater LED Light Model Numbers SAVI-NOTE7, SAVI-NOTE0 Table of Contents Safety Precautions...2 SaVi Note Install Instructions...3- M Instructions...- Warnings READ AND

More information

Panduit Recommended Best Case Practice Split Fibre

Panduit Recommended Best Case Practice Split Fibre Panduit Recommended Best Case Practice Split Fibre Panduit Corp. 2009 BEST PRACTICES PN526 Table of Contents 1.0 Enclosure Prep... 2 2.0 Fibre Cable Prep and Installation... 2 3.0 Pigtail Installation...

More information

Remote Tuner Options for the DXE-MBVE-1 Vertical Antenna

Remote Tuner Options for the DXE-MBVE-1 Vertical Antenna Remote Tuner Options for the DXE-MBVE-1 Vertical Antenna DXE-MBVE-1UGBRT3 for the MFJ-993BRT 300 Watt Remote Tuner DXE-MBVE-1UGBRT4 for the MFJ-994BRT 600 Watt Remote Tuner DXE-MBVE-1UGRT8 for the MFJ-998RT

More information

Quick Release Roof-Mount Kit MB700

Quick Release Roof-Mount Kit MB700 Quick Release Roof-Mount Kit MB700 Owner s Manual Thank you for purchasing a KING product! The KING Quick Release Roof-Mount provides a convenient way to securely mount your KING antenna to your vehicle,

More information

LCC (Little Coaxial Connector) Installation Instructions)

LCC (Little Coaxial Connector) Installation Instructions) LCC (Little Coaxial Connector) Installation Instructions) Content Page INTRODUCTION...1 Revision History...1 Trademark Information...1 1 TOOLS...2 1.1 Connection Tool Kit...2 1.2 Tool Illustrations...2

More information

INSTALLATION INSTRUCTIONS MO023A

INSTALLATION INSTRUCTIONS MO023A INSTALLATION INSTRUCTIONS MO023A Nexans N3S ODF system NEXANS N3S ODF SYSTEM Content Product description Patching frame Splice frame Doors Splice module Patch module Protective cover and label panel Guides

More information

Installation instructions Ex frames

Installation instructions Ex frames General information Installation and maintenance: For European member countries of GENELEC shall standard EN 60079-14 and EN 60079-17 be considered. For countries members of IECEx shall standard IEC 60079-14

More information

INTRODUCTION INSTALLATION LIGHTNING RETARDING LOOPS. Figure 1. Relay Box Antenna Connections. Relay Box Cable Connections

INTRODUCTION INSTALLATION LIGHTNING RETARDING LOOPS. Figure 1. Relay Box Antenna Connections. Relay Box Cable Connections INTRODUCTION The Ameritron RCS-8V is a remote controlled coaxial RF switch that will operate with negligible loss, radiation and VSWR at all frequencies up to 250 MHz. Only a slight compromise in VSWR

More information

OWNER'S MANUAL SIGNAL COMMANDER

OWNER'S MANUAL SIGNAL COMMANDER OWNER'S MANUAL SIGNAL COMMANDER THIS MANUAL CONTAINS INSTRUCTIONS FOR: LPDA 200 - INSTALLATION - OPERATION - TROUBLESHOOTING - EXPLODED PARTS DRAWING - WARRANTY AntennaTek, Inc. 425 S. Bowen, #4 Longmont,

More information

VITALink Taped Splice Straight Through Crimp

VITALink Taped Splice Straight Through Crimp A Marmon Wire & Cable Berkshire Hathaway Company VITALink Taped Splice Straight Through Crimp 2 Hour Fire-Rated Splice VITALink MC Cables, UL FHIT 120 Installation Instructions Description The VITALink

More information

REQUIRED TOOLS. Wire cutters Razor blade Soldering iron Pliers 11/16 Wrench for Tube 18mm Wrench for Ring

REQUIRED TOOLS. Wire cutters Razor blade Soldering iron Pliers 11/16 Wrench for Tube 18mm Wrench for Ring S9122 PWS BNC MALE CABLE MOUNT COMPRESSION CONNECTOR S9022 PWS N TYPE MALE CABLE MOUNT COMPRESSION CONNECTOR S9322 PWS TNC MALE CABLE MOUNT COMPRESSION CONNECTOR The PWS S9122 is a BNC male cable mount

More information

VGA Extender LR EXT-VGA-141LR. User s Manual

VGA Extender LR EXT-VGA-141LR. User s Manual VGA Extender LR EXT-VGA-141LR User s Manual ASKING FOR ASSISTANCE Technical Support: Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday thru

More information

FOSC 400 C5 & D5 Fiber Optic Splice Closures

FOSC 400 C5 & D5 Fiber Optic Splice Closures FOSC 400 C5 & D5 Fiber Optic Splice Closures I N S T A L L A T I O N I N S T R U C T I O N 1. General Product Information The FOSC 400 C5 and D5 closures are combination cable closures and splice organizers,

More information

Desk Mount Articulating Dual Monitor Arm with Cable Management & Height Adjust

Desk Mount Articulating Dual Monitor Arm with Cable Management & Height Adjust Desk Mount Articulating Dual Monitor Arm with Cable Management & Height Adjust ARMDUAL *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com

More information

GENUINE PARTS. SIRIUS Under Glass Antenna Kit

GENUINE PARTS. SIRIUS Under Glass Antenna Kit GENUINE PARTS SATELLITE RADIO INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Satellite Radio System 2. APPLICATION: Pathfinder (2006-2007) 3. PART NUMBERS: XM Tuner Kit 999U9-AS005 SIRIUS Tuner Kit 999U9-AS006

More information

FOSC 400 B2/B4. Fiber Optic Splice Closures. Table of Contents. Page 1

FOSC 400 B2/B4. Fiber Optic Splice Closures. Table of Contents. Page 1 FOSC 400 B2/B4 I N S T A L L A T I O N I N S T R U C T I O N Fiber Optic Splice Closures Table of Contents Page 1. General Product Information 2 2. Warnings 3 3. Required Tools and Materials 3 4. Standard

More information

LANsense Modular Patch Panel for 24 Snap-in Connectors 1 HU. empty. Clip-on. with Sliding mechanism. Black or white INSTALLATION GUIDE

LANsense Modular Patch Panel for 24 Snap-in Connectors 1 HU. empty. Clip-on. with Sliding mechanism. Black or white INSTALLATION GUIDE LANsense Modular Patch Panel for 24 Snap-in Connectors 1 HU empty Clip-on with Sliding mechanism Black or white INSTALLATION GUIDE LANsense Modular Patch Panel for 24 Snap-in Connectors Document information

More information

LANmark PCB patch panel, 1HU INSTALLATION GUIDE. LANmark PCB patch panel, 1 HU

LANmark PCB patch panel, 1HU INSTALLATION GUIDE. LANmark PCB patch panel, 1 HU LANmark PCB patch panel, 1HU INSTALLATION GUIDE LANmark PCB patch panel, 1 HU Document information Document reference Release September 2001 Published by Contact address BRO-009 LANmark PP 1HU 0701 Nexans

More information

A449-6S 70 CENTIMETER FM YAGI ANTENNA MHz

A449-6S 70 CENTIMETER FM YAGI ANTENNA MHz ASSEMBLY AND INSTALLATION A449-6S 70 CENTIMETER FM YAGI ANTENNA 440-450 MHz COMMUNICATIONS ANTENNAS 951425 (7/93) WARNING THIS ANTENNA IS AN ELECTRICAL CONDUCTOR. CONTACT WITH POWER LINES CAN RESULT IN

More information

OmniReach FTTX Solutions RealFlex DLX Universal Drop Cable Instruction Sheet

OmniReach FTTX Solutions RealFlex DLX Universal Drop Cable Instruction Sheet OmniReach FTTX Solutions RealFlex DLX Universal Drop Cable Instruction Sheet ADCP-90-457 Issue 1 9/2010 Content Page INTRODUCTION.............................................................................

More information

ALTOS LITE Loose Tube, Gel-Free Cables with FastAccess Technology, Fibers

ALTOS LITE Loose Tube, Gel-Free Cables with FastAccess Technology, Fibers ALTOS LITE Loose Tube, Gel-Free Cables with FastAccess Technology, 12-72 Fibers P/N 004-223-AEN Issue 1 1. General This procedure describes cable-end and mid-span sheath removal and fiber access of ALTOS

More information

3M 710 Splicing System. Modular. Solutions. for Copper Splicing

3M 710 Splicing System. Modular. Solutions. for Copper Splicing 3M 710 Splicing System Modular Solutions for Copper Splicing A History of Strong Copper Networks The reliability of a copper conductor communication system depends greatly upon the reliability of the individual

More information

Installation instructions, accessories. Subwoofer. Volvo Car Corporation Gothenburg, Sweden. Page 1 / 29

Installation instructions, accessories. Subwoofer. Volvo Car Corporation Gothenburg, Sweden. Page 1 / 29 Installation instructions, accessories Instruction No 30752136 Version 1.1 Part. No. 30752135 Subwoofer Volvo Car Corporation Subwoofer- 30752136 - V1.1 Page 1 / 29 Equipment A0000162 A0000161 A0801178

More information

OWNER'S MANUAL SIGNAL COMMANDER

OWNER'S MANUAL SIGNAL COMMANDER OWNER'S MANUAL SIGNAL COMMANDER THIS MANUAL CONTAINS INSTRUCTIONS FOR: MOD 550 - INSTALLATION - OPERATION - TROUBLESHOOTING - EXPLODED PARTS DRAWING - WARRANTY AntennaTek, Inc. 425 S. Bowen, #4 Longmont,

More information

Electrical Markets 3M ScotchCode Wire Marking and Identification System. Quality. Marking. For Most Projects

Electrical Markets 3M ScotchCode Wire Marking and Identification System. Quality. Marking. For Most Projects Electrical Markets 3M ScotchCode Wire Marking and Identification System Quality Marking For Most Projects Dispensers 3M ScotchCode Dispenser STD-TAG The proprietary 3M ScotchCode Dispenser STD-TAG simplifies

More information

Cold Shrink Straight Joint

Cold Shrink Straight Joint Cold Shrink Straight Joint 3M QS2000E 22 kv Single Core Straight Joint Instruction Sheet All dimensions shown are in mm unless otherwise stated Kits contains components for one single core cable -2-2*

More information

Loose Tube Cable Mid-Span Access for Splicing For Series 11D, 1GD, 12D, 1AD, 1DD, 1CD, 11, 1G, 12, 12L, 1A, 1D, 1C, 1NY, 13, 1H, HZD and HZA

Loose Tube Cable Mid-Span Access for Splicing For Series 11D, 1GD, 12D, 1AD, 1DD, 1CD, 11, 1G, 12, 12L, 1A, 1D, 1C, 1NY, 13, 1H, HZD and HZA Loose Tube Cable Mid-Span Access for Splicing For Series 11D, 1GD, 12D, 1AD, 1DD, 1CD, 11, 1G, 12, 12L, 1A, 1D, 1C, 1NY, 13, 1H, HZD and HZA NOTE: These installation instructions have been written for

More information

User Manual CXE Rev (12) CXX Series. User Manual. Teleste Corporation CXE810. Fibre optic receiver

User Manual CXE Rev (12) CXX Series. User Manual. Teleste Corporation CXE810. Fibre optic receiver 27.3.2012 1(12) CXX Series User Manual Teleste Corporation CXE810 Fibre optic receiver 27.3.2012 2(12) Contents Introduction... 3 Installation... 3 Housing... 3 Powering... 4 Interfaces... 4 Fibre installation...

More information

3A TC 699/SIP/UK/12

3A TC 699/SIP/UK/12 Hybrid OTIAN Node I N S T A L L A T I O N I N S T R U C T I O N Generic Joint 3A - Item Code 006825 TC 699/SIP/UK/12 07/15 - Helpline 01793 572453 Contents 1 General description 2 Capacity 3 Kit contents

More information

GENUINE PARTS SATELLITE RADIO INSTALLATION INSTRUCTIONS. 1. DESCRIPTION: Satellite Radio System 2. APPLICATION: Frontier (2006~)

GENUINE PARTS SATELLITE RADIO INSTALLATION INSTRUCTIONS. 1. DESCRIPTION: Satellite Radio System 2. APPLICATION: Frontier (2006~) GENUINE PARTS SATELLITE RADIO INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Satellite Radio System 2. APPLICATION: Frontier (2006~) Xterra (2006~) 3. PART NUMBERS: XM Tuner Kit 999U9-AS003 SIRIUS Tuner Kit

More information

Fiber ICT. Optical Fiber Catalogue

Fiber ICT. Optical Fiber Catalogue Catalogue Index Registers RFP 24-24 Fibers indoor wallmount box..... 02 RFP 48-48 Fibers indoor wallmount box..... 02 RFS 8-8 Fibers wallmount box..... 02 PATCH-24F - Patch Panel F.O. 9 with 24 SC/APC....

More information

C 303-RF Tri-element Array Microphone Instructions

C 303-RF Tri-element Array Microphone Instructions C 303-RF Tri-element Array Microphone Instructions C 303-RF Installation Instructions Packaging C 303 microphone Enclosure with 2.5 Metre (8ft) cae Link cable Cable gland It may be easier to remove the

More information

XW3D. Simple Wiring of Sensor Actuators. Connector Terminal Boxes. Specifications. Materials and Finish. Connection Combinations

XW3D. Simple Wiring of Sensor Actuators. Connector Terminal Boxes. Specifications. Materials and Finish. Connection Combinations Terminal Boxes XWD CSM_XWD_DS_E Simple Wiring of Sensor Actuators Greatly reduce wiring in combination with the Smartclick XS. Insert the connector and turn / of a turn to lock the connectors. Higher rated

More information

3M Cubitron. II Fibre Disc 982C and 987C Now available in grades 36+, 60+ and 80+ Engineered. Perfection. Epic Performance.

3M Cubitron. II Fibre Disc 982C and 987C Now available in grades 36+, 60+ and 80+ Engineered. Perfection. Epic Performance. 3M Cubitron II Fibre Disc 982C and 987C Now available in grades, and Engineered Perfection. Epic Performance. The Future is Now. Leave conventional abrasives in the past and do more than you thought possible

More information

QCA9-33 Active Combiner

QCA9-33 Active Combiner Product Manual QCA9-33 Active Combiner April 13, 2012 Table of Contents Table of Contents... 2 Overview... 3 Specifications... 4 Installation... 5 Basic Setup... 5 16-Channel Operation... 5 16-64 Channel

More information

TECHNICAL GUIDE. For Air-Cooled MIG Guns - 350, 450 and 550 amp SAFETY AND WARRANTY INFORMATION INSTALLATION MAINTENANCE GUIDE TECHNICAL DATA OPTIONS

TECHNICAL GUIDE. For Air-Cooled MIG Guns - 350, 450 and 550 amp SAFETY AND WARRANTY INFORMATION INSTALLATION MAINTENANCE GUIDE TECHNICAL DATA OPTIONS TECHNICAL GUIDE For Air-Cooled MIG Guns - 350, 450 and 550 amp SAFETY AND WARRANTY INFORMATION INSTALLATION MAINTENANCE GUIDE TECHNICAL DATA OPTIONS EXPLODED VIEW & PARTS LIST TROUBLESHOOTING Certified

More information

Mediacom Upgrade/Splicing Procedures (based on original document from Corporate dated 4/16/98)

Mediacom Upgrade/Splicing Procedures (based on original document from Corporate dated 4/16/98) Mediacom Upgrade/Splicing Procedures (based on original document from Corporate dated 4/16/98) 1. Splicing specifications are provided by Mediacom, but due to resplice conditions, many locations become

More information

JACK Digital HDTV Over-the-Air Antenna

JACK Digital HDTV Over-the-Air Antenna JACK Digital HDTV Over-the-Air Antenna w/built-in SureLock Digital TV Signal Meter TM OA8200-White OA8201-Black SPECIFICATIONS Dimensions: 11.25 H x 16 W x 12.5 L Powered Amplifier +12 volt / 100 ma working

More information

Crane Systems Extension Reel Cable Guide Hardware Kit

Crane Systems Extension Reel Cable Guide Hardware Kit Purpose Extension Reel Cable Guide Hardware Kit Greer Number K056005 The Extension Reel Cable Guide Hardware Kit is used to control the reel-off cable along the telescoping boom and the signal cable routed

More information

TECHNICAL GUIDE. TOUGH GUN ThruArm G2 Series Robotic MIG Guns for FANUC Robots 100iC, 100iC-6L, 120iC, 120iC-10L INSTALLATION MAINTENANCE

TECHNICAL GUIDE. TOUGH GUN ThruArm G2 Series Robotic MIG Guns for FANUC Robots 100iC, 100iC-6L, 120iC, 120iC-10L INSTALLATION MAINTENANCE TECHNICAL GUIDE TOUGH GUN ThruArm G2 Series Robotic MIG Guns for FANUC Robots 100iC, 100iC-6L, 120iC, 120iC-10L INSTALLATION MAINTENANCE TECHNICAL DATA OPTIONS EXPLODED VIEW & PARTS LIST ORDERING INFORMATION

More information

SPECIFICATION FIBER OPTIC SPLICE CLOSURE. Spec No : VSS-1007-BS403A-04A/SD. VSS-0107-BS403A-04A/SD R & D Center Manufacturing Division

SPECIFICATION FIBER OPTIC SPLICE CLOSURE. Spec No : VSS-1007-BS403A-04A/SD. VSS-0107-BS403A-04A/SD R & D Center Manufacturing Division SPECIFICATION FIBER OPTIC SPLICE CLOSURE Model Spec. No. Distribution Depts. VSOF-BS403A VSS-0107-BS403A-04A/SD R & D Center Manufacturing Division Sales Division Management Division Revision 10. 07 (Rev.4)

More information

3M ScotchCode Wire Marking and Identification System. Identify with 3M

3M ScotchCode Wire Marking and Identification System. Identify with 3M 3M ScotchCode Wire Marking and Identification System Identify with 3M Dispensers 3M ScotchCode Wire Marker Tape Dispenser STD The 3M ScotchCode Wire Marker Tape Dispenser STD is a compact, carry-along

More information

Doorphone Video Intercom

Doorphone Video Intercom HOME SERIES INSTRUCTION MANUAL Doorphone Video Intercom with Colour 4.3 LCD Monitor EN Getting to know your LCD Screen (Front) 1 2 3 4 5 6 1) LCD Screen - This is where you view your visitor that the intercom

More information