User Guide. Dakota Micro, Inc. Quad View Monitoring System. TROUBLESHOOTING. Part Numbers: DMOV-7M-C1(2)

Transcription

1 TROUBLESHOOTING Problem Possible Causes No picture, no sound Improper connection with 12v power adapter. Use of unauthorized power supply. Power Switch is on OFF position No picture Check whether AV cable is securely plugged in No sound Check whether audio connector is secure, or the sound volume is turned off or down Dark picture Ensure that bright and contrast settings are properly adjusted. Ensure monitor is warm enough No color Ensure color settings are properly adjusted in menu Upside down or lateral inverted picture Check horizontal/vertical adjustment on remote. No car-backing function (i.e. Picture) Event trigger is not securely connected Remote Controller Fault Battery may be dead or improperly installed: replacement battery Model:CR2025,3V Quad View ing System User Guide Part Numbers: DMOV-7M-C1(2) Remote controller is not pointed in the direction of the receiving sensor: Make sure remote is pointed at the monitor Long distance or improper angle: The effective distance between the remote controller and the receiving sensor is 7 meters and the angle is ±30. Obstacle: Move any obstacles out of the path Dakota Micro, Inc th Ave. SE Cayuga, ND

2 Consumer Limited Warranty (North America ONLY) FEATURES 7 LED Backlit, high resolution TFT LCD screen Wide voltage input: 11-32V 3 Channel Inputs, displays 3 images consecutively Manual or automatic image switching modes Forward/Mirror image selection Event Triggers provided for all 3 cameras. Cameras can be triggered for events such as backing up or door opening Power provided to only active camera, prolonging the life of the cameras. AV input and output jacks provided Auto ON/OFF LED sensor automatically triggers night vision when required Includes credit card style remote control Backlit control buttons enable easy menu navigation in all lighting conditions NOTES Please read entire manual before using our products Before you power your rear view monitoring system, ensure that all cables are properly connected to avoid damage to the system IS NOT WATERPROOF, please do not place the monitor outdoors Ensure that all cables are routed a sufficient distance from high temperature areas and rotary objects To ensure proper heat dispersal, ensure that vent holes in monitor remain clear Do not open the monitor or camera casing, doing so will void the warranty DO NOT watch DVD s etc. while driving Please do not use caustic chemicals to wipe the camera and/or monitor Dakota Micro, Inc. (Hereinafter referred to as DM) warrants to the first consumer purchaser that this DM brand product will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period of 18 (eighteen) months. Warranty extends throughout North America (US & Canada). 1 year warranty applies to all other geographic locations unless otherwise states in writing by DM. This warranty does not apply to any appearance items of the product nor any part of the exterior of the product which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in design or construction. Neither the sales personnel of the seller, nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of DM. The warranties described herein shall be the sole and exclusive warranties granted by DM and shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of DM to the purchaser with respect to the product. DM shall not be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so that above exclusion may not apply to you. Any action at law, suit in equity, or other judicial proceeding for the enforcement of any warranty provided for herein or otherwise, will be instituted only in the Courts of the State of North Dakota, the laws of which shall govern. WARNING There are no reparable parts in the system, so please do not attempt to This warranty gives you specific legal rights and you may also have other rights, which may vary from state to state. take apart the camera or the monitor should a malfunction occur, doing so will void your warranty. Call the factory at for repair issues. 1 10

3 Included Components I. Introduction LED Backlit LCD Screen Sun Visor A/V output w/ bracket *Camera(s) w/ bracket remote control Power/Video harness *20M power/video cable(s) 12v lighter adaptor Earphone Remote Receiver VolVol+ Menu Down Up/CAM Selection CDS Sensor for controlling the button backlights. DO NOT BLOCK II. Specifications Connection Chart LED backlit, Digital Screen TFT LCD Color Size 7 Inch Connector Digital TTL Resolution 800(RGB) 480 No. Camera Inputs 3 CAM2 Visible Angle (LR/UD) 140 / 110 CAM3 Contrast 0:1 Volume (nits) 300 Response Time (ms) 25 Event Trigger wire (brown*) Event Trigger wire CAM2 (blue*) Event Trigger wire CAM3 (white*) 12v power FUSE extension cable extension cable extension cable 1) Cameras 1-3 have an available event trigger wire. Cameras are identified as 1,2 and 3. - Yellow connector CAM2 - Red connector CAM3 - Black connector 2) Regardless if monitor is ON or in Standby mode, if power is applied to the trigger, activated camera will become powered * Event Trigger wire colors are subject to change without notice and may vary slightly from colors indicated above. 9 Bracket Camera Switch ON/OFF *DMOV-7M-C1 includes x1 camera and x1 power/video cable *DMOV-7M-C2 includes x2 cameras and x2 power/video cables LCD Color Color System PAL/NTSC (AUTO) Support Three Camera Inputs 1.0Vp-p75Ω Audio Output W 1W Loudspeaker φ 4. 0cm,16Ω/1W Connector DVI24+1 Power Source DC11-32V Free Power Input Consumption MIN 8W, MAX 20W (four cameras ON) External dimensions(mm) 185 X W 124 X T48 (without mounting) Weight 400g 2

4 Camera III. Install/Remove Sun Visor Installation Bracket Screws Bracket Screws Top Clip-buckle Pus h M on ito S un sh ad r Complete e OverView Camera Mon itor with suns hade Mounting Bracket Top Bottom Clip-buckle Remove Top Clip-buckle Pu ll su ns ha Push de Pu ll Mounting Bracket Base mon itor with suns hade pre ss m on ito h Pus Bo tto m C lip -b uc r Camera Specifications pr es s kl e IV. Installation of Bracket Screw Screw 3 Image pick-up Device 1/3" Sharp Color CCD TV System NTSC/PAL (depending upon model) Lens Mount 420 TV lines Horizontal Resolution Internal Synchronization Sync System NTSC 510(H) x 492(V) PAL 0(H) x 562(V) Number of Pixels 0 Lux at Night (IR LED ON) Usable Illumination CDS Auto Control Under 10 Lux by CDS Operation Temp -20 C - +C Power Supply DC 12v +/-10% Weight Weight 4g Environmental Watertight 8

5 Remote Control V. Operation: III. Button Function MUTE Mute to turn sound off to resume volume, press Mute again o r p ress V OL+ ME NU P OWER F or O N/OFF Vol - CH button (up/down) CH (D o wn) To s elect m e nu CH (U p ) or CH (Down) Menu Vol+ V OL-/+ a. Adj u s t volu m e of monitor. b.a dju s t brigh t ness,contr a st,etc. c. Ac tiv a t e other functions, such as: mirror/normal image switch, delay time adjustment, etc. Menu D isp lay. Down Up ON/Standby AV/CAM select Switch 1. ON\Standby to turn monitor ON/OFF. 2. Me n u Instr u ction Menu key to disp l ay a s f ollowing: PICTURE, M I RROR, TRIGDELAY, S YSTEM a. P ICTURE MODE: User can use t his key t o se l ect fo u r mode s : sta n dard c olor,soft colo r, ric h color and bright. PICTURE BRIGHTNESS CONTRAST SATURATION CALL t his button is to display currently displayed AV channel SELECT SLEEP/TIMER Time setup of sleep off, it is used to set the time off within 120 minutes. ADJUST Language Language selection of Chinese or English, Up/Down to select brightness, press Vol+/-to set up the value between 0 and 100. Up/Down to select CONTRAST/SATURATION/HUE. pressvol+/- to set the value. AV1/AV2/AV3 this button to toggle between the 3 video inputs b. CHANNEL OPTIONS CHANNEL OPTION CAM2 CAM3 CH PRIORITY CH DELAY DELAY TIME this button to flip the picture horizontally. this button to flip the picture vertically. SELECT 7 NORMAL MIRROR MIRROR 0S ADJUST Up/Down to select / CAM2 / CAM3 Vol+/-to set up Normal/Mirror image of / CAM2 / CAM3 - key to select channel priority. L/R key to choose priority camera - key to select channel delay. L/R key to choose delay camera Down key to select delay time. Use L/R key to adjust time up to 30 sec. 4

6 Remote Control I. Introduction c. System Mute SYSTEM LANGUAGE ON/Standby ENGLISH Volume+ Up \ CAM Selection SELECT ADJUST 7 Volume- Menu Down Call Up/Down to select Lang u ag e, pr e ss Vol+/- to select Chinese/English. Mode Sleep Language AV Channel Switch Calendar Horizontal Flip Vertical Flip II. Replace Battery Pull 5 Model of Battery : (CR2025) 6