Version as of: 15 February Part number:

Transcription

1

2 The information furnished in this manual is for informational use only and is subject to change without notice. Please check for latest version. Vari-Lite assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual. All information and graphics are property of Vari-Lite, a Philips group company, Petal Street Dallas, Texas USA. All other brand or product names which may be mentioned in this manual are trademarks or registered trademarks of their respective companies or organizations. Version as of: 15 February 2011 Part number: VL1100CD ERS Luminaire User s Manual Vari-Lite, a Philips group company. All Rights Reserved.

3 FOREWORD How To Obtain Warranty Service A copy of the Vari-Lite Limited Warranty was included in the shipping package for this VARI LITE product. To obtain warranty service, please contact customer service at VARI-LITE ( ) or or via at entertainment.service@philips.com request a Return Material Authorization (RMA) for warranty service. You will need to provide the model and serial number of the item being returned, a description of the problem or failure and the name of the registered user or organization. If available, you should have your sales invoice to establish the date of sale as the beginning of the warranty period. Once you obtain the RMA, pack the unit in a secure shipping container or in its original packing box. Fill out the RMA form included at the end of this manual and place in shipping container along with a copy of your invoice (if available). Write the RMA number legibly on or near the shipping address label and return the unit, freight prepaid to: Vari-Lite Attention: Warranty Service (RMA#: ) Petal Street Dallas, Texas USA As stated in the warranty, it is required that the shipment be insured and FOB our service center February 2011 i

4 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Compliance Notice FCC This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when this equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with Vari-Lite system, service, and safety guidelines, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his/her own expense. Declaration of Conformity We declare, under our sole responsibility, that this product complies with the relevant clauses of the following standards and harmonized documents: Safety: (by Low Voltage Directive 2006/95/EC) EN : 1997/A1:1998 EN : 1989/A2:1991 EN60922 Electromagnetic Compatibility: (by Council Directive 2004/108/EC) EN55022:1998, Class A EN : 1995, Performance Criteria: B EN : 1995, Performance Criteria: A EN : 1995, Performance Criteria: B EN : 1995, Performance Criteria: B EN : 1996, Performance Criteria: A EN : 1996, Performance Criteria: A EN : 1994, Performance Criteria: B and C EN : 1995 EN : 1994 We certify that the product conforms to the protection requirements of Low Voltage Directive 2006/ 95/EC and Council Directive 2004/108/EC (EMC). ii 15 February

5 FOREWORD Safety Notice It is extremely important to read ALL safety information and instructions provided in this manual and any accompanying documentation before installing and operating the products described herein. Heed all cautions and warnings during installation and use of this product. Safety symbols used throughout this manual are as follows: CAUTION advising of potential damage to product. WARNING advising of potential injury or death to persons. GENERAL INFORMATION PERTAINING TO PROTECTION AGAINST ELECTRICAL SHOCK, FIRE, EXPOSURE TO EXCESSIVE UV RADIATION, AND INJURY TO PERSONS CAN BE FOUND BELOW. WARNING: INSTRUCTIONS FOR CONTINUED PROTECTION AGAINST FIRE 1. VARI LITE luminaires have been designed for use with specific lamp types. The VL1100CD ERS luminaire requires a Philips lamp - 315W ceramic discharge, long-life lamp. Installing another type of lamp may be hazardous. 2. Luminaires may be mounted on any type of surface as long as mounting instructions are followed. See instructions detailed in this manual. 3. Note distance requirement from combustible materials or illuminated objects for VARI LITE luminaires. WARNING: INSTRUCTIONS FOR CONTINUED PROTECTION AGAINST ELECTRICAL SHOCK 1. VARI LITE luminaires are designed for dry locations only. Exposure to rain or moisture may damage luminaire. 2. Disconnect power before servicing any VARI LITE equipment. 3. Servicing to be performed by qualified personnel only February 2011 iii

6 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL WARNING: INSTRUCTIONS FOR CONTINUED PROTECTION AGAINST EXCESSIVE EXPOSURE TO UV RADIATION 1. Many VARI LITE luminaires use a lamp that produces UV radiation. DO NOT look directly at lamp. 2. It is hazardous to operate luminaires without lens or shield. Shields, lenses, or ultraviolet screens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired. For example, by cracks or deep scratches. WARNING: INSTRUCTIONS FOR PROTECTION AGAINST INJURY TO PERSONS 1. Exterior surfaces of the luminaire will be hot during operation. Use appropriate safety equipment (gloves, eye protection, etc.) when handling and adjusting hot equipment and components. 2. Luminaires will have a hot lamp when operating. Disconnect power and allow lamp to cool before replacing. 3. Arc lamps emit ultraviolet radiation which can cause serious skin burn and eye inflammation. Additionally, arc lamps operate under high pressure at very high temperatures. Should the lamp break, there can exist a danger of personal injury and/or fire from broken lamp particles being discharged. 4. Wear eye protection when relamping. 5. Appropriate safety equipment (gloves, eye protection) should be used when handling damaged lamps. 6. If lamp is touched with bare hands, clean lamp with denatured alcohol and wipe with lint-free cloth before installing or powering up the luminaire. 7. The lamp shall be changed if it has become damaged or thermally deformed. WARNING: RF INTERFERENCE 1. This is a Class A product. In a domestic environment this product may cause radio interference, in which case, the user may be required to take adequate measures. iv 15 February

7 FOREWORD Sicherheitshinweise Es ist äußerst wichtig, ALLE Sicherheitsinformationen und -hinweise in diesem Handbuch und dem beiliegenden Informationsmaterial zu lesen, bevor Sie die hierin beschriebenen Produkte installieren bzw. bedienen. Halten Sie bei der Installation und dem Einsatz dieses Produkts alle Warnhinweise und Vorsichtsmaßnahmen ein. Folgende Sicherheitssymbole werden in diesem Handbuch verwendet: VORSICHT - weist auf möglichen Produktschaden hin. WARNUNG - weist auf mögliche Körperverletzung und Lebensbedrohung hin. NACHSTEHEND FINDEN SIE ALLGEMEINE HINWEISE ÜBER SICHERHEITSVORKEHRUNGEN GEGEN ELEKTROSCHOCK, FEUER, ÜBERHÖHTE UV- STRAHLUNG UND KÖRPERVERLETZUNGEN. WARNUNG: HINWEISE ZUM FEUERSCHUTZ 1. VARI LITE-Scheinwerfer sind ausschließlich für den Einsatz mit bestimmten Lampentyps. Achten Sie auf den Lampentyp (Philips lamp - 315W ceramic discharge, long-life lamp), bevor Sie die jeweiligen Lampen ersetzen. Die Installation eines anderen Lampentyps kann gefährlich sein. 2. Scheinwerfer können auf jeder beliebigen Oberfläche montiert werden, solange Sie die Montageanweisungen befolgen. Detaillierte Hinweise finden Sie in diesem Handbuch. 3. Beachten Sie die Einhaltung des erforderlichen Sicherheitsabstandes der VARI LITE- Scheinwerfer von brennbarem Material oder beleuchteten Objekten. WARNUNG: HINWEISE ZUM SCHUTZ GEGEN ELEKTROSCHOCK 1. VARI LITE-Scheinwerfer eignen sich ausschließlich für trockene Standorte. Regen oder Feuchtigkeit können die Scheinwerfer beschädigen. 2. Unterbrechen Sie die Stromzufuhr, bevor Sie mit der Arbeit an VARI LITE-Geräten beginnen. 3. Die Geräte sollten nur von qualifiziertem Personal gewartet werden February 2011 v

8 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL WARNUNG: HINWEISE ZUM SCHUTZ GEGEN ÜBERHÖHTE UV-STRAHLUNG 1. Viele VARI LITE-Scheinwerfer verwenden die Lampentyp, der UV-Strahlen abgibt. SCHAUEN SIE NICHT direkt in die Lampe. 2. Es ist gefährlich, Leuchten ohne Linsen oder Blenden zu bedienen. Blenden, Linsen oder Ultraviolettschirme müssen ausgetauscht werden, sofern deren Schutzwirkung durch sichtbare Beschädigung (z. B. Sprünge oder Schrammen) eingeschränkt ist. WARNUNG: HINWEISE ZUM SCHUTZ GEGEN KÖRPERVERLETZUNGEN 1. Bei Betrieb sind die Außenflächen der Scheinwerfer heiß. Verwenden Sie bei der Bedienung von aufgeheizter Apparatur die jeweils geeignete Sicherheitsausrüstung (Handschuhe, Augenschutz etc.). 2. Bei Betrieb der Scheinwerfer ist die Lampe heiß. Unterbrechen Sie die Stromzufuhr und lassen Sie die Lampe abkühlen, wenn Sie diese austauschen. 3. Bogenlampen senden ultraviolette Strahlen aus, die Hautverbrennungen und Augenentzündungen verursachen können. Der Betrieb von Bogenlampen erfolgt unter Hochdruck und bei hohen Temperaturen. Sollte die Lampe zerbrechen, besteht die Gefahr von Körperverletzung bzw. von Feuer, das von Lampenteilen ausgelöst werden kann. 4. Tragen Sie beim Austausch der Lampen einen Augenschutz. 5. Die geeignete Sicherheitsausrüstung (Handschuhe, Augenschutz) sollte beim Umgang mit beschädigten Lampen verwendet werden. 6. Wenn die Lampe mit bloßen Händen berührt wird, reinigen Sie sie mit denaturiertem Alkohol und einem flusenfreien Tuch, bevor Sie die Scheinwerfer installieren oder in Betrieb nehmen. 7. Wenn die Lampe beschädigt oder durch Hitzeeinwirkung deformiert ist, muß diese ausgetauscht werden. WARNUNG: HF-INTERFERENZ 1. Es handelt sich um ein Produkt der Klasse A. In einer Wohnumgebung kann das Produkt Hochfrequenzstörungen verursachen. In diesem Fall müssen eventuell geeignete Maßnahmen getroffen werden. vi 15 February

9 FOREWORD Notes de sécurité Avant de procéder à l installation des produits décrits dans ce guide et de les mettre en marche, il est extrêmement important de lire TOUS les renseignements et TOUTES les directives de sécurité contenues dans ce guide ainsi que toute documentation jointe. Tenir compte de tous les avertissements et suivre toutes les précautions pendant l installation et l utilisation de cet appareil. Les symboles de sécurité utilisés dans ce guide sont les suivants : ATTENTION Ce symbole annonce que l appareil risque d être endommagé. AVERTISSEMENT Ce symbole annonce qu il y a risque d accident grave ou même fatal. CETTE SECTION CONTIENT DES INFORMATIONS GÉNÉRALES POUR SE PROTÉGER CONTRE LES DÉCHARGES ÉLECTRIQUES, LES INCENDIES, L EXPOSITION EXCESSIVE AUX RAYONS UV ET TOUT AUTRE ACCIDENT POUVANT ENTRAÎNER DES BLESSURES. AVERTISSEMENT: DIRECTIVES POUR SE PROTÉGER CONTRE LES INCENDIES 1. Les luminaires VARI LITE ont été conçus pour être utilisés uniquement avec certaines type de lampes. Vérifier le type de lampe (Philips lamp - 315W ceramic discharge, long-life lamp) avant de remplacer les lampes. L installation d un autre type de lampe peut poser un danger. 2. Les luminaires peuvent être fixés sur tout type de surface tant que les directives de montage sont respectées. Voir les explications détaillées dans ce guide. 3. Vérifier la distance à respecter entre les matériaux combustibles ou les objets illuminés et les luminaires VARI LITE. AVERTISSEMENT: DIRECTIVES POUR SE PROTÉGER CONTRE LES DÉCHARGES ÉLECTRIQUES 1. Les luminaires VARI LITE sont conçus pour une utilisation au sec uniquement. Une exposition à la pluie et à l humidité risque d endommager le luminaire. 2. Débrancher l appareil avant de procéder à la révision de tout matériel VARI LITE. 3. Les révisions doivent être effectuées uniquement par des personnes qualifiées February 2011 vii

10 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL AVERTISSEMENT: DIRECTIVES POUR SE PROTÉGER CONTRE UNE EXPOSITION EXCESSIVE AUX RAYONS UV 1. Plusieurs luminaires VARI LITE utilisent une lampe qui produit des rayons UV. NE PAS fixer son regard sur la lampe. 2. L utilisation des luminaires sans lentille ou blindage pose des risques. Tous blindages, lentilles ou écrans ultraviolet visiblement endommagés au point que leur efficacité en est affectée doivent être remplacés, par exemple s il y a des fissures ou de profondes rayures. AVERTISSEMENT: DIRECTIVES POUR SE PROTÉGER CONTRE LES ACCIDENTS POUVANT ENTRAÎNER DES BLESSURES 1. Les surfaces externes du luminaire deviennent brûlantes quand l appareil est en marche. Pour manœuvrer ou ajuster des appareils brûlants et leurs composants, se protéger suffisamment (gants, protection pour les yeux, etc.). 2. La lampe du luminaire est brûlante lorqu il est en marche. Débrancher le courant et attendre que la lampe ait refroidi avant de la remplacer. 3. Les lampes à arc émettent des rayons ultraviolets pouvant causer de graves brûlures sur la peau et une inflammation des yeux. De plus, les lampes à arc fonctionnent sous haute tension à de très hautes températures. Si la lampe se casse, les particules de la lampe cassée peuvent causer blessures et/ou incendie en s éparpillant. 4. Se protéger les yeux pour remplacer la lampe. 5. Utiliser des appareils de protection appropriés (gants, protection des yeux) pour manier des lampes endommagées. 6. Si la lampe a été touchée avec des mains nues, la nettoyer avec de l alcool dénaturé et l essuyer avec un chiffon non-pelucheux avant d installer ou de brancher le luminaire. 7. Si la lampe a été endommagée ou a reçu une déformation thermique, elle doit être remplacée. AVERTISSEMENT: INTERFÉRENCE RF 1. Cet appareil est de Classe A. Dans un environnement domestique, cet appareil peut causer des interférences radio, et si c est le cas, l utilisateur peut avoir à prendre des mesures adéquates. viii 15 February

11 FOREWORD Aviso sobre Seguridad Es muy importante leer TODA la información e instrucciones sobre seguridad que se indica en este manual así como en los documentos adjuntos antes de instalar y operar los productos descritos. Se debe prestar atención a todos los avisos y advertencias durante la instalación y uso de este producto. Los símbolos de seguridad usados en este manual son los siguientes: CUIDADO, indica posibles daños al producto. ADVERTENCIA, indica posibles lesiones o muerte a las personas. LA INFORMACIÓN GENERAL RELACIONADA A LA PROTECCIÓN CONTRAGOLPES DE CORRIENTE ELÉCTRICA, INCENDIO, EXPOSICIÓN EXCESIVA A RADIACIÓN ULTRA VIOLETA Y LESIONES A LAS PERSONAS SE PUEDE ENCONTRAR SEGUIDAMENTE: ADVERTENCIA: INSTRUCCIONES PARA PROTECCIÓN CONTINUA CONTRA INCENDIO 1. Las luminarias VARI LITE han sido diseñadas para ser usadas solamente con algunas lámparas. Tome nota del tipo de lámpara (Philips lamp - 315W ceramic discharge, long-life lamp) antes de reemplazarla. Instalación de otro tipo de lámpara puede ser peligroso. 2. Las luminarias se pueden instalar en cualquier tipo de superficie siempre que se sigan las instrucciones de instalación. Vea las instrucciones detalladas en este manual. 3. Tome nota de los requerimientos de distancia de materiales combustibles u objetos iluminados para las luminarias VARI LITE. ADVERTENCIA: INSTRUCCIONES PARA PROTECCIÓN CONTINUA CONTRA CHOQUE ELÉCTRICO 1. Las luminarias VARI LITE están diseñadas solamente para lugares secos. La exposición a la lluvia o humedad pueden dañar la luminaria. 2. Desconecte la energía antes de dar servicio a cualquier equipo de VARI LITE. 3. El servicio debe ser realizado solamente por personal calificado February 2011 ix

12 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL ADVERTENCIA: INSTRUCCIONES PARA PROTECCIÓN CONTINUA CONTRA LA EXPOSICIÓN EXCESIVA DE RADIACIÓN ULTRA VIOLETA 1. Muchas luminarias VARI LITE usan un tipo de lámpara que produce radiación UV. NO mire directamente a la lámpara. 2. Es peligroso operar luminarias sin lentes o protectores. Debe cambiar los protectores, lentes o pantallas ultravioletas si se aprecia que han sido dañadas, y que su efectividad pudiera estar deteriorada. Por ejemplo, si tuvieran rajaduras o raspaduras profundas. ADVERTENCIA: INSTRUCCIONES PARA PROTECCIÓN CONTRA LESIONES DE PERSONAS 1. Las superficies exteriores de las luminarias están calientes durante su operación. Use un equipo de seguridad apropiado (guantes, protección para los ojos, etc.) cuando haga ajustes en el equipo y componentes que están calientes. 2. Cuando las luminarias están en operación la lámpara estará muy caliente. Desconecte la energía y deje que la lámpara se enfríe antes de reemplazarla. 3. Las lámparas de arco emiten radiaciones ultravioletas que pueden ocasionar serias quemaduras a la piel e inflamación a los ojos. Además, las lámparas de arco operan a alta presión y muy alta temperatura. Si la lámpara se rompe, puede existir el peligro de lesiones al personal o un incendio ocasionado por las partículas de la lámpara rota que se caen. 4. Use protección para los ojos cuando vuelve a colocar una lámpara nueva. 5. Use un equipo de seguridad apropiado (guantes, protección para los ojos, etc.) cuando trabaje con lámparas dañadas. 6. Si toca la lámpara con las manos, limpie la lámpara con alcohol desnaturalizado y con tela sin pelusas antes de instalar o volver a conectar la luminaria. 7. Cambie la lámpara si está dañada o deformada termicamente. ADVERTENCIA: INTERFERENCIA RF 1. Este es un producto de Clase A. En el ambiente de la casa este producto puede ocasionar radiointerferencia, en cuyo caso, el usuario debe tomar las medidas adecuadas. x 15 February

13 FOREWORD February 2011 xi

14 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL xii 15 February

15 TABLE OF CONTENTS Table of Contents Introduction About This Manual... 1 Text Conventions... 1 Additional Documentation... 1 Customer Service... 2 Chapter 1. Description Features Standard Features... 4 Model Specific Features... 4 Components Included Items... 5 Luminaire Overview... 6 Accessories VL1100CD ERS Replacement Items/Accessories... 7 Chapter 2. Installation Power and Data Cabling Requirements AC Power Current vs. Voltage Data Cables Recommended Cable Types/Manufacturers DMX Termination Connector Loopback Connector Installation Procedures Installing Lamp Accessory Frame Holder Hanging the Luminaire Connecting Data and Power Powering Up Power-Up and Configuration Overview Standard Power Up Procedure Power Up and Configuration Procedure Align Lamp For Maximum Beam Irradiance Addressing Program Starting Address Program Starting Address Without Calibrating Chapter 3. Operation DMX Operation Channel Mapping February 2011 xiii

16 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Control Channel Functions DMX Data Display DMX Mapping Color Mixing Rotating Gobo Wheel Index/Rotation Shutter Mechanism Luminaire Timing Timing Channel Information Updating Software USB Download and Programming Luminaires Transferring Software From Luminaire to Luminaire Chapter 4. Menu System Menu Operation What Is the Menu System? Menu Controls Operation Menu Default State Menu Shortcuts Menu Functions Menu System Overview Menu System Function Chart Menu Function Definitions Self Tests Running Parameter Tests Appendix A. Troubleshooting and Maintenance Troubleshooting Error Messages Troubleshooting Guide Routine Maintenance Cleaning Optical Lenses and Gobos Rotating Gobo Replacement Lamp Replacement Appendix B. Technical Specifications Mechanical Optical Operational xiv 15 February

17 INTRODUCTION : ABOUT THIS MANUAL Introduction About This Manual This manual provides necessary information regarding safety, installation, operation and routine maintenance for the VARI LITE VL1100CD Ellipsoidal Reflector Spotlight (ERS) luminaire. Familiarizing yourself with this information will help you to get the most out of your product. WARNING: It is important to read ALL accompanying safety and installation instructions to avoid damage to the product and potential injury to yourself or others. This manual covers the following models: Model Part Number Source Integral Dimmer Shutter Iris Fixture Color VL1100CDS W CDM Lamp On-board glass dimmer wheel VL1100CDS W CDM Lamp On-board glass dimmer wheel VL1100CDI W CDM Lamp On-board glass dimmer wheel VL1100CDI W CDM Lamp On-board glass dimmer wheel Yes No Black Yes No White No Yes Black No Yes White Text Conventions The following styles and meanings are used throughout this manual: Style [Button] [Up] / [Down] arrows MENU Meaning Front panel button. Example: Press [Menu]. Press either [Up] or [Down] arrow button at Menu Display. LCD Menu Display read-out. Example: Press [Up] / [Down] arrows until LAMP appears. Additional Documentation A service manual for Authorized VARI LITE Service Centers and technicians of the VL1100CD ERS luminaire is available in electronic (PDF) format: VL1100CD ERS Luminaire Service Manual ( ) - Testing, Troubleshooting, Component Replacement and Illustrated Parts Breakdown February

18 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Note: Performing maintenance procedures may void the product warranty. Refer to the Vari-Lite Limited Warranty card included in the product shipping package for more information. For more information regarding DMX512 systems, refer to the following document available from United States Institute for Theatre Technology, Inc. (USITT): Digital Data Transmission Standard for Dimmers & Controllers plus AMX 192 Analog Multiplex Data Transmission Standard for Dimmers & Controllers. USITT 6443 Ridings Road Syracuse, New York USA Tel: (800) Fax: (866) / Customer Service Our Goal At Vari-Lite, we are committed to providing you the highest quality in customer service. Our comprehensive resources are available to help your business succeed and ensure you get the full benefit of being a Vari-Lite customer. Whether your needs are telephone troubleshooting assistance, product training or technical service, our full-time staff of experienced professionals are on-hand to provide support. How to Reach Us For assistance in your area, call the dealer from which your product was purchased. or Contact an Authorized Service Center. or Contact the Vari-Lite Customer Service Department, 9am -6pm CST Monday through Friday, at the following: Phone: VARI-LITE ( ) or entertainment.service@philips.com Additional Resources For additional resources and documentation, please visit our website at and follow the Support link February

19 CHAPTER 1. Description This chapter contains descriptions of luminaire features and components, along with a list of accessories which are available. Features Components Accessories February

20 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Features Standard Features VL1100CD Ellipsoidal Reflector Spotlight (ERS) luminaires have the following standard features: 315W ceramic discharge, long-life lamp. Automated zoom optics system. Crossfading CYM color system. All motors utilize a noise reducing, 50kHz. drive system that quiets operation during movement and also while static. Intensity control through a glass dimmer wheel that provides full-field dimming designed for smooth timed fades. Diffusion system. Six-position rotating gobo wheel (five rotatable, indexable gobo positions and one open gobo position). Repositional pan/tilt system via 3-phase stepper motors. High-frequency drivers to reduce stationary noise when luminaire is in parked position. Control by DMX512 protocol. Note: Additional specifications and information is found in Technical Specifications on page 63. Model Specific Features Each individual configuration has the following specific features: VL1100CD ERS Luminaire ( Black / White) Four-blade shutter framing system. VL1100CD ERS Luminaire ( Black / White) Beam-size iris mechanism February

21 DESCRIPTION : COMPONENTS 1 Components Included Items The following illustration shows the included components for all models. Included Items Warranty Card Product Support Sheet Unpack & Quick Start Guide 315W CDM Lamp VL1100 CD ROM (User s Manual) Product Registration Neutrik PowerCon AC Input Connector VL1100CD Luminaire February

22 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Luminaire Overview The following illustration shows the external luminaire components and controls. Input Panel Provides DMX In and Thru, and AC Power connections. Base Provides hook mounting holes and safety cable connection. Power Input Connector Latch Gel, Silk or Frost Yoke Leg (Control) Contains main control PCB and display PCB. Menu Display (not shown) Used to input manual commands, program, test, set defaults and access internal status information. Yoke Leg (Power) Contains power supply, and lamp ignitor board. Accepts frames or top hats Accessory Frame Accessory Frame Holder Beam Adjustment Controls Accessory Frame Holder Provides frame for optional silks, frosts, color. correction or top hats. See detail... Menu Display Controls Backcap Assembly Provides access to lamp for replacement and provides controls for beam adjustment. Head Assembly Houses color, gobo, dimmer, strobe, and optional shutter or iris mechanisms. LCD Display Input Panel Connections Beam Adjust Screws * * Do not remove or use to access lamp. Address MENU ENTER Press to show menu, or if at first level, the current address. Down / Decrease Up / Increase Press to select current menu option or current data value. Data In Data Thru 3-Pole Neutrik Locking Connector for AC Input 6 15 February

23 DESCRIPTION : ACCESSORIES 1 Accessories VL1100CD ERS Replacement Items/Accessories The following optional and/or replacement items can be ordered directly from Vari-Lite. (Please order by Vari-Lite part number.) VARI-LITE P/N ACCESSORY Safety Cable Assembly DMX Loopback Connector Assembly DMX Terminator, 120 Ohm USB Luminaire Programming Kit (Includes USB Upload Cable, Programming Kit CD ROM, Carry Bag, and Instructions)* Neutrik PowerCon NAC 3 FCA AC Inlet Connector Truss Hook, Mega-Clamp, Round and Square Truss Hook, Mega-Claw for 2 Round Tube W CDM Lamp - Philips XXXX VL1000 Gobo (specify pattern from Vari-Lite catalog to complete P/N). Note, VL1100CD luminaires use the same size gobos as VL1000 luminaires. Contact your Authorized VARI LITE Dealer or Vari-Lite customer service for assistance. Note: * For more information on the USB Luminaire Programming Kit, please see USB Download and Programming Luminaires on page February

24 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Notes 8 15 February

25 CHAPTER 2. Installation This chapter contains instructions for installation of all version of the VL1100CD ERS Luminaire. It includes connecting power and data, along with instructions for powering up the luminaire for the first time and addressing it within your system. Power and Data Cabling Requirements Installation Procedures Powering Up Addressing February

26 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Power and Data Cabling Requirements AC Power WARNING: Do not power a VL1100CD ERS Luminaire from a dimmed circuit - even in "Non- Dim" mode. Dimmer and non-dim modules are not suitable sources of power because their output modifies the AC wave form. This may work for a short time, but will eventually result in power problems, luminaire mis-operation and/or failure. Using a dimmer or non-dim module to power your VARI LITE luminaire will void your luminaire s warranty. The luminaire requires standard AC power distribution from VAC, 50/60 Hz in order to power all internal electronics and motors. It is equipped with a 3-pole Neutrik PowerCon locking connector (with contacts for line, neutral, and premating safety grounds) for the purpose of AC input. The mating Neutrik PowerCon connector is supplied, however, you will need to purchase or construct a cable appropriate for your application. Wire* Green/Yellow Blue Brown Connection AC Ground AC Neutral AC Line * International (Harmonized) Standard VL1100CD Input Panel Neutrik PowerCon Connector (supplied) 3-Pole Neutrik Locking Connector for AC input Current vs. Voltage Figure 2-1: Power Connector The following tables provide the luminaire s current draw at specific voltages. (Currents given are worst case with all motors sequencing.) Table 2-1: VL1100CD Current vs. Voltage (Total Fixture Power) 60Hz Current A A February

27 INSTALLATION : POWER AND DATA CABLING REQUIREMENTS 2 Data Cables The luminaire is equipped with two, 5-pin XLR connectors for DATA IN and DATA THRU (out) applications. DATA IN requires a 5-pin, female XLR connector and DATA THRU requires a 5-pin, male XLR connector. When purchasing or constructing data cables, it is important that not only the correct cable type be used, but also quality cable to ensure a reliable DMX512 system. Your cabling should meet the following USITT DMX specification requirements: Suitable for use with EIA485 (RS485) operation at 250k baud. Characteristic impedance ohms, nominally 120 ohms. Low capacitance. Two twisted pairs. Foil and braid shielded. 24 AWG min. gauge for runs up to 1000 feet (300m). 22 AWG min. gauge for runs up to 1640 feet (500m). Note: Microphone type cables and other general purpose, two-core audio or signal cables are not suitable for use with DMX512. Refer to the USITT Recommended Practice for DMX512 guide for additional information regarding DMX512 systems. How to obtain a copy is detailed in Additional Documentation on page 1. The XLR 5-pin connectors should be wired as follows: Data Thru Cable Pinout Male Conn Pin 1 Foil & Braided Shield Pin/Wire Code to XLR Connectors Pin 2 1st conductor of 1st twisted pair Data (-) Pin 3 2nd conductor of 1st twisted pair Data (+) Pin 4 1st conductor of 2nd twisted pair Data (-) Pin 5 2nd conductor of 2nd twisted pair Data (+) Data In Cable Pinout Female Conn February

28 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Recommended Cable Types/Manufacturers These are only a few of the suitable cable types. Any quality EIA485, twisted pair, 120 ohm, shielded cable will also work. Type Pairs ZΩ Jacket AWG Use Temp (F) Belden Cables 1215A PVC 26 IBM Type 6 Office cable A PTFE 22 (Solid) High Temp, Plenum 200 cable PVC 24 UL PVC 28 UL PVC 24 UL PTFE 24 High Temp, Plenum 200 cable PTFE 24 High Temp, Plenum 200 cable PTFE 22 High Temp, Plenum 200 cable PTFE 24 High Temp, Plenum 200 cable PTFE 22 High Temp, Plenum 200 cable PVC 24 UL PVC 28 UL PVC 24 UL PVC 24 UL PC224P Polyurethane * Characteristic Impedance Proplex Cables 22 Heavy Duty and Portable PC224T PVC 22 UL PC226T PVC 22 UL February

29 INSTALLATION : POWER AND DATA CABLING REQUIREMENTS 2 DMX Termination Connector A male XLR DMX termination connector is required at the last luminaire (or "far end of the line") to prevent signal reflections. Signal reflections may cancel out the signal at certain line lengths, resulting in errors. The terminator is also necessary for software downloads and running tests on multiple luminaires. To construct your own connector, you will need the following components: 5-pin, male XLR connector. Two 1/4W 5% 120 ohm resistors Solder resistors across pins 2 & 3, and 4 & 5 5 Note: A male termination connector is available as an accessory from Vari-Lite. See Accessories on page 7. Loopback Connector When transferring software versions from luminaire to luminaire, a loopback connector is required at the first luminaire in the data link. To construct your own connector, you will need the following components: 5-pin, female XLR connector. Two small segments of 22 AWG wire Solder wires across pins 2 & 4, and 3 & Note: A loopback connector is available as an accessory from Vari-Lite. See Accessories on page February

30 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Installation Procedures Installing Lamp In the event the lamp was packed separately during shipment, it will be necessary to install before use. WARNING: Ensure that power is completely removed from luminaire when installing lamp. CAUTION: Wear cotton gloves or other covering while installing lamp. Touching lamp glass with bare fingers will leave oil and may cause the lamp to explode or reduce lamp life. If touched, use alcohol and cotton cloth to thoroughly clean glass portion of lamp. To install arc lamp: Step 1. Ensure power is removed from luminaire. Step 2. At backcap, gradually loosen two 10-32x2-3/8" PPSS black screws (Figure 2-2) a few turns at a time until backcap is free. (Screws must be alternately loosened to prevent one side from locking up.) Backcap Interior View Rear Head Assembly CAUTION: Do not touch lamp with bare fingers. Backcap Align when re-installing Alignment Stud (2) CAUTION: Alignment Hole (2) Holes and studs MUST be aligned when re-installing x2-3/8 PPSS Black Screws (captive) - loosen each gradually Figure 2-2: Removing Backcap February

31 INSTALLATION : INSTALLATION PROCEDURES 2 Step 3. Grip lamp by base and firmly install in socket. CAUTION: Do not touch lamp with bare fingers. Socket Lamp Install lamp, firmly pressing into place. Figure 2-3: Installing VL1100CD Lamp in Socket Step 4. Re-install backcap, ensuring that alignment studs and holes are aligned (Figure 2-2). Step 5. Align lamp. (Refer to Align Lamp For Maximum Beam Irradiance on page 23.) February

32 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Accessory Frame Holder An accessory frame holder is provided for the addition of a top hat or gel frame with silks, frosts or color correction if required. The frame holder is designed to fit a standard 7.5-inch gel frame or top hat. To remove and replace frame or top hat: Step 1. Disconnect luminaire AC input cable from power source. Step 2. At front lens, press upward on accessory frame latch and turn to open. Step 3. Remove frame/top hat, if any (Figure 2-4). Step 4. Install frame/top hat and close latch. Press Up and Turn Latch Gel, Silk, or Frost Head Assembly Accessory Frame NOTE: The accessory frame is not a Vari-Lite accessory. Figure 2-4: Installing a Frame or Top Hat February

33 INSTALLATION : INSTALLATION PROCEDURES 2 Hanging the Luminaire The luminaire can be hung horizontally or vertically from any structure designed to work with the type of load created by this moving luminaire. The pan tube base provides two mounting holes for attaching truss hooks or other mounting hardware as required. Many compatible truss hooks are available from different manufacturers for your particular needs. The Mega Claw Truss Hook, shown in the example illustration below, can be ordered separately from Vari-Lite (refer to VL1100CD ERS Replacement Items/Accessories on page 7). To install truss hooks (if required): Step 1. At pan tube base, attach two truss hooks as shown below (Figure 2-5). Step 2. Tighten hardware securely. WARNING: Attach truss hooks securely. Mega Claw Truss Hooks (not provided) VL1100CD Pan Tube Base Hook Hardware (not provided) Figure 2-5: Example VL1100CD Luminaire Truss Hook Installation February

34 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL To hang luminaire in truss: Step 1. Lift luminaire into mounting position. Step 2. Secure in place with truss hooks. Ensure truss hook hardware that locks hook in place (e.g. wing bolt) is properly tightened and that luminaire is fully supported. Step 3. Attach safety cable (sold separately) as follows: a. Connect end of cable to mounting pin at one side of pan tube base. b. Loop at least once around pipe and attach other end at second mounting pin. Step 4. Connect power and data cables according to procedure given in Connecting Data and Power on page 19. Safety Cable: Recommended for all hanging installations or as may be required by local codes. 26.5" (67.3cm) 17.5" (44.5cm) 35.5" (90.2cm) 26" (66cm) Safety cable securing points on fixture. Figure 2-6: Example VL1100CD Luminaire Truss Hanging Installation February

35 INSTALLATION : INSTALLATION PROCEDURES 2 Connecting Data and Power A maximum of 32 luminaires may be connected in any one DMX data link. Note: This maximum limit applies to the luminaire "daisy chain" only. Your system or console may require fewer luminaires on a single data link path. Consult your console documentation for more information. To connect power and data: Step 1. After luminaire(s) are installed, connect data cable from console to first luminaire in chain at DATA IN connector. Step 2. If required, connect additional data cables from DATA THRU connectors to DATA IN connectors of remaining luminaires in link. Step 3. At last luminaire in link, install DMX termination connector at DATA THRU connector. (Luminaires and other devices on the same DMX chain may not function properly without termination.) Data Thru Data Thru Data In from console DMX Termination Step Step Figure 2-7: Data Connection 4. Connect AC Input Cable connector to power input source. 5. Dress cables and secure them so that they will not interfere with luminaire head and yoke movement February

36 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Powering Up Power-Up and Configuration Overview First Power-Up When powering up a VL1100CD ERS Luminaire for the first time, the lamp type and shutter settings must be configured. This procedure will usually happen prior to delivery. However, in the event that it has not been done or if the Main Controller Board has been replaced, it will be necessary. Follow one of these two power-up procedures depending on whether the luminaire requires configuration: Already configured - Standard Power Up Procedure on page 21. Not configured - Power Up and Configuration Procedure on page 22. Calibration Sequence After AC power is applied, the luminaire will start powering up (this will take seconds) and then begin a calibration sequence that steps it through full pan and tilt movements. The internal mechanisms will also move through a full range of motion. After calibration, the luminaire head will either stop at its "home" position (which positions the pan axis at mid-rotation and the head parallel to the yoke with the lens pointing away from the luminaire upper enclosure) or move to its current defined position if DMX data is present. All internal mechanisms also move to their "home" or defined positions. Depending on the luminaire s setting for Lamp Power-Up State (refer to Menu System Function Chart on page 49), when power is applied the lamp will either a) strike or ignite - Lamp On (default), b) await calibration and then strike - Cal On, or c) await manual command to strike - Lamp Off. Importance of Correct Configuration The configuration settings MUST be correct or the luminaire will not operate properly. The configuration settings specify whether or not the luminaire contains a shutter system or beam-size iris, which will then affect the DMX mapping of the luminaire. For example, choosing the shutter option will configure the luminaire for 27 DMX channels, while not choosing the shutter option will configure it for 19 DMX channels. When the luminaire is configured as having no shutter, the option for the beam-size iris becomes available. Refer to Channel Mapping on page 26 for more detailed information on this subject February

37 INSTALLATION : POWERING UP 2 Standard Power Up Procedure Use this procedure when powering up a luminaire that has already been configured. (Refer to Power- Up and Configuration Overview on page 20.) Note: Refer to Chapter 4: Menu System for detailed instructions on menu functions. CAUTION: Before applying power, be sure the luminaire is hung or positioned so that the head and yoke can move freely without restriction. To power up luminaire: Step 1. At each luminaire, apply power by switching on power source. Luminaire will display Starting for seconds, and then automatically step through the following procedure: 1) If Lamp Power-Up State is set to Lamp On, lamp will strike (ignite). 2) Luminaire will cycle through calibration and stop at "home" position. 3) If Lamp Power-Up State is set to Cal On, lamp will strike (ignite) at end of calibration sequence. 4) If Lamp Power-Up State is set to Lamp Off, them Luminaire will cycle through calibration and stop at "home" position. Lamp will not strike (ignite) until a Lamp On command is received by luminaire February

38 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Power Up and Configuration Procedure Use this procedure when powering up a luminaire that has not been previously configured. (Refer to Power-Up and Configuration Overview on page 20.) Note: Refer to Chapter 4: Menu System for detailed instructions on menu functions. CAUTION: Before applying power, be sure the luminaire is hung or positioned so that the head and yoke can move freely without restriction. To configure luminaire at power up: Step 1. At each luminaire, apply power by switching on power source. Step 2. For unconfigured luminaires, menu will display LampType. Press [Enter] to move to next level. Step 3. Press [Up]/[Down] to toggle options. For VL1100CD luminaires, you must choose CD option. Set selection by pressing [Enter]. Note: When CD is selected, the menu system will update to include the Dimmer, DMX, and Manual commands. (Dimmer will be added even if no dimmer is present.) Step Step 4. Press [Up]/[Down] to select Shutter?. Press [Enter] to move to next level. 5. Press [Up]/[Down] to toggle options. Choose either Yes or No by pressing [Enter]. Note: If the luminaire is configured NOT to have the shutter system, the menu will automatically update to include the beam-size iris assembly (even if one is not present), DMX, and Manual commands. Step 6. Luminaire will display Starting for seconds, and then automatically step through following procedure: 1) If Lamp Power-Up State is set to Lamp On, lamp will strike (ignite). 2) Luminaire will cycle through calibration and stop at "home" position. 3) If Lamp Power-Up State is set to Cal On, lamp will strike (ignite) at end of calibration sequence. 4) If Lamp Power-Up State is set to Lamp Off, them Luminaire will cycle through calibration and stop at "home" position. Lamp will not strike (ignite) until a Lamp On command is received by luminaire February

39 INSTALLATION : POWERING UP 2 Align Lamp For Maximum Beam Irradiance After a new lamp is installed in the luminaire, it will be necessary to align the lamp to optimize the beam. WARNING: Backcap and adjustment screws will be HOT during lamp operation. Wear gloves and/ or use tools to prevent burns. To align lamp: Step 1. Set intensity to 100%. Step 2. Position beam on a white wall at a distance of 10 to 20 feet. Step 3. Using console or internal luminaire menu controls, set zoom to zero and focus to a hard edge. If installed, be sure that beam-size iris and shutters are open. Step 4. Using three adjustment screws, adjust hot spot to center of beam (Figure 2-8). Step 5. Check color uniformity as follows: a. Position one of the color stages at 30% of maximum. (Cyan or Magenta work best.) b. Verify that beam color is uniform (if lamp is misaligned, color will be concentrated to one side of beam). If color is not uniform, readjust lamp until color is uniform across entire beam field. Beam Adjustment Acorn Knobs * * Do not remove or use to access lamp. Figure 2-8: Lamp Alignment Screws Note: The nature of the CDM lamp used in the VL1100CD ERS Luminaire prevents it from restriking when it is hot after use. It takes approximately 15 minutes for the lamp to cool enough to restrike February

40 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Addressing Program Starting Address The DMX starting address is entered using the Menu Display. This address will be retained even if the power is removed. Note: Refer to Chapter 4: Menu System for detailed instructions on menu functions. Note: Refer to your console operating instructions for specific information regarding its addressing requirements. To program a DMX starting address: Step 1. Press [Menu]. Step 2. Press [Up] / [Down] arrows until Address appears. Press [Enter]. Step 3. DMX will appear. Press [Enter]. Step 4. Press [Up] / [Down] arrows to enter starting address. Step 5. Press [Enter] to set. Program Starting Address Without Calibrating It is possible to bypass the calibration sequence and go directly to the Menu Display programming in order to pre-program an address setting. To program starting address without calibrating luminaire: While powering up luminaire, press and hold [Menu]. Program address as in Program Starting Address above. Release when display reads ":" Note: The luminaire will require a reset to restore control February

41 CHAPTER 3. Operation This chapter contains instructions for operating the luminaire using DMX control and for updating the internal software. DMX Operation DMX Mapping Luminaire Timing Updating Software February

42 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL DMX Operation Channel Mapping These tables assume a DMX start address of 1. When a different starting address is used, this address becomes channel 1 function and other functions follow in sequence. (There is only one DMX mode for this luminaire, which is Enhanced 16-bit Mode.) Table 3-1: Enhanced 16-Bit Mode - VL1100D Iris (I) Models DMX Channel Parameter Range 1 Dimmer * Hi Byte Pan Lo Byte Pan Hi Byte Tilt Lo Byte Tilt Edge Zoom 0 (small) (big) 8 Diffusion 0 (open) (diffused) 9 Blue 0 (open) (full saturation) 10 Amber 0 (open) (full saturation) 11 Magenta 0 (open) (full saturation) 12 Rotating Gobo index rotate Gobo Index Index: Rotate: 0 (cw max) (cw min) (stop) (ccw min) (ccw max) 15 Beam 0 (small) (open) 16 Focus Time Color Time Beam Time Control * Dimmer refers to an internal dimmer for VL1100CD Iris models February

43 OPERATION : DMX OPERATION 3 Table 3-2: Enhanced 16-Bit Mode - VL1100CD Shutter (S) Models DMX Channel Parameter Range 1 Dimmer * Hi Byte Pan Lo Byte Pan Hi Byte Tilt Lo Byte Tilt Edge Zoom 0 (small) (big) 8 Diffusion 0 (open) (diffused) 9 Blue 0 (open) (full saturation) 10 Amber 0 (open) (full saturation) 11 Magenta 0 (open) (full saturation) 12 Rotating Gobo index rotate Gobo Index (13 = Hi Byte) (14 = Lo Byte) * Dimmer refers to an internal dimmer for VL1100CD Shutter models. Index: Rotate: 0 (cw max) (cw min) (stop) (ccw min) (ccw max) 15 Frame 1A 0 (open) (closed) 16 Frame 1B 0 (open) (closed) 17 Frame 2A 0 (open) (closed) 18 Frame 2B 0 (open) (closed) 19 Frame 3A 0 (open) (closed) 20 Frame 3B 0 (open) (closed) 21 Frame 4A 0 (open) (closed) 22 Frame 4B 0 (open) (closed) 23 Rotate Frame center 24 Focus Time Color Time Beam Time Control February

44 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Control Channel Functions Control channel functions allow special actions such as reset, lamp on/off and partial recalibration. These must be executed with zero time transition or with timing disabled. Discrete values must be used; not manual controls such as faders or encoders (see chart below for values). Reset - resets all luminaire mechanisms. Lamp On or Lamp Off - switches lamp on or off. Partial Recalibration - resets only the target mechanism (color, gobo, zoom, etc.) without affecting others. Table 3-3: Control Channel Functions Control Channel Function % Value Control Channel Value * For arc models, the dimmer will close during each recalibration action. For 3 Secs or Greater DMX Value After 3 Secs Luminaire Reset Lamp Off Lamp On Partial Recalibration of: - Blue/Amber/Magenta/Diffuser * Rotating Gobo/Index * Edge/Zoom * Beam Size Iris/Shutter * To use control channel functions: Step 1. Select an action to be sent. Step 2. Set control channel value for desired action (for example, 84 for reset). Hold value for 3 seconds. Note: A numerical keypad is required for sending values. An encoder or fader does not allow for a quick value change, which is required to effect the control functions. Step 3. Set control channel value to zero. (This must occur without any scaling values. Action will be voided if other values are detected between action value and zero.) February

45 OPERATION : DMX OPERATION 3 DMX Data Display The DMX data display shows the data received for the given luminaire and does not show the entire stream of 512 bytes. It shows only the number of channels used for the given luminaire model in 16- bit enhanced mode. For example, a VL1100CD (shutter model) luminaire with an address of 40 will show DMX Channels 1-27 which would correlate to DMX Channels February

46 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL DMX Mapping Color Mixing The color mixing mechanism is a CYM subtractive color mixing system made up of a graduated color system for cyan, yellow, and magenta. Table 3-4: DMX Map For Cyan % Value DMX Value Action 0 0 Open Closed or Full Saturation Table 3-5: DMX Map For Yellow % Value DMX Value Action 0 0 Open Closed or Full Saturation Table 3-6: DMX Map for Magenta % Value DMX Value Action 0 0 Open Closed or Full Saturation February

47 OPERATION : DMX MAPPING 3 Rotating Gobo Wheel Note: Gobos are sold separately. Contact your Authorized VARI LITE Dealer or visit the Vari-Lite web site, for available gobo patterns. The function operates in two modes: INDEX Mode and ROTATE Mode. The DMX values corresponding to these modes are as follows: DMX values will select each gobo in Indexing mode. DMX values will select each gobo in Rotating mode. Table 3-7: DMX Map For Gobo Index/Rotate Position Indexing Rotating Function Open Gobo Gobo Gobo Gobo Gobo 5 Index/Rotation The Gobo Index function utilizes 16-bit control which offers enhanced resolution whether in INDEX or ROTATE mode. Table 3-8: Index/Rotation Range Function Range Index Rotate 0 (cw max) (cw min) (stop) February

48 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Shutter Mechanism For units with a shutter mechanism, the shutter is comprised of four frame blades that move independently or in unison. The entire assembly operates in a smooth, time-continuous motion using stepper motors (two per frame blade and one to rotate the entire shutter mechanism). The shutter mechanism can rotate 45 o in either direction and the frame blades can tilt +/- 35 o. Table 3-9: Shutter Mechanism DMX Map Chart (shutter models only) Item % Value DMX Value Action Frame 1A 0 0 Open to Frame 4B Closed Shut Rot 0 0 CCW (Shutter Center Rotation) CW February

49 OPERATION : LUMINAIRE TIMING 3 Luminaire Timing Timing Channel Information Timing channel control improves the timed moves of certain groups of parameters. We provide three timing channels, one for Focus (Pan and Tilt), one for color parameters and one for beam parameters. Timing channels support time values of up to six minutes. Table 3-10: Channel Function / Timing Channel Relationship Channel Function Pan (Hi Byte/Lo Byte) Tilt (Hi Byte/Lo Byte) Blue Amber Magenta Color Wheel Diffusion Beam Edge Zoom Rotating Gobo Gobo Index (HiByte/LoByte) Shutter (all 9 motors) Timing Channel Focus Time Color Time Beam Time A timing value of zero is full speed. A time value of 100% (or 255 in DMX) causes the associated parameter(s) to follow cue fade time (console time) rather than the timing channel. Note: The particular storing syntax for your console, as well as instructions on how to write part cues, can be found in the operation manual for that console. To use these channels, you must: Step 1. Create the cue, including color, gobo, edge and diffusion as required. Step 2. Decide which fixtures and which parameter groups will use timing channels. Step 3. Assign a value to the particular timing channel(s) you wish to use (for timing information see chart on next page). Step 4. Set console timing (or cue fade time) for parameters and timing channels to zero seconds. Step 5. Store cue February

50 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Note: Avoid changing timing channel values in a fading cue. This can cause unexpected behavior in the luminaire as the timing channel value is updated over time. Timing channel values and the final destination of the parameters affected by the timing channel should always be sent in a zero count. Timing channels can be set in either % or (DMX) modes, with the following values assigned: Table 3-11: VL1100CD Timing Channels Map % Value DMX = Seconds 0 Full Speed February

51 OPERATION : LUMINAIRE TIMING 3 Table 3-11: VL1100CD Timing Channels Map % Value DMX = Seconds February

52 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Table 3-11: VL1100CD Timing Channels Map % Value DMX = Seconds February

53 OPERATION : LUMINAIRE TIMING 3 Table 3-11: VL1100CD Timing Channels Map % Value DMX = Seconds February

54 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Table 3-11: VL1100CD Timing Channels Map % Value DMX = Seconds February

55 OPERATION : LUMINAIRE TIMING 3 Table 3-11: VL1100CD Timing Channels Map % Value DMX = Seconds February

56 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Table 3-11: VL1100CD Timing Channels Map % Value DMX = Seconds Follows Cue Data February

57 OPERATION : UPDATING SOFTWARE 3 Updating Software USB Download and Programming Luminaires You can upgrade Vari-Lite luminaire operating software using the USB Luminaire Programming Kit (Vari-Lite part number , sold separately) for desktop computers and newer laptops equipped with USB 2.0 ports. The USB Luminaire Programming Kit can be ordered directly from your Authorized VARI LITE Dealer. The VARI LITE USB Luminaire Programming Kit ( ) includes: VARI LITE USB Upload Cable ( ) USB Luminaire Programming Kit CD ( ) Instruction Sheet ( ) VARI LITE carry bag ( ) Computer Requirements for the USB Luminaire Programming Kit PC running Windows 98, 2000, XP, or Vista. Although the USB Luminaire Programming kit software is not directly compatible with Macintosh computers, it does run with some Windows emulators. In addition to Windows, your computer must be running IE 5.01 or later, and Microsoft.NET Framework Version 3.5 (or later), which you can download from and search for.net Framework downloads. An available USB 2.0 port on the PC. USB VLDownloader PC Program and.bin Luminaire Files The USB VLDownloader program and current.bin files are available from the Product Downloads page at Instructions for installing the USB VLDownloader program on your PC are also available on the Product Downloads page. Use the USB VLDownloader program to transfer updated versions of the luminaire operating software (.bin files) from your PC to the luminaires. Note: Refer to instruction sheet for detailed programming instructions for VARI LITE luminaires February

58 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Lists specific versions of downloaded software (on PC) Click to download specific software version to connected luminaire(s) Device Connection Status and USB Downloader Controls Click logo to go to Vari-Lite web site (internet connection required) Download History Will show current progress of download Figure 3-1: VL Download Program Window Transferring Software From Luminaire to Luminaire It is possible to transfer specific software versions between luminaires. As in the case of installing new software versions, multiple luminaires can be programmed at the same time when they are data linked together (refer to Connecting Data and Power on page 15), however, only a maximum of 32 luminaires can be updated at once. Hardware Requirements Data cables used in this process must have two twisted pairs and a shield. It is also recommended that cables meet all other USITT DMX specification requirements. Refer to Data Cables on page February

59 OPERATION : UPDATING SOFTWARE 3 A termination connector is used in this process. Refer to page 10 for more information regarding the construction of this connector. Master luminaire containing software version to download Luminaire 1 requiring update Luminaire 2 requiring update Data Thru Data Thru Loopback Connector DMX Termination Connector Figure 3-2: Software Transfer Setup Transfer Procedure This procedure is used to transfer software versions between luminaires. Step 1. At last luminaire, install male termination connector into DATA THRU XLR connector. Step 2. At master luminaire (first in chain) Menu Display, press [Menu]. Step 3. Press [Up] / [Down] arrows until Fixture appears. Step 4. Press [Up] / [Down] arrows until Download appears. Press [Enter]. Step 5. OK? will be displayed. Press [Enter] to accept. Step 6. Download proceeds. (Download takes 4-5 seconds.) The number of blocks displayed is less in a luminaire-to-luminaire download than in a PC-to-luminaire download for the same software version. Step 7. When download is complete, luminaire automatically recalibrates. When recalibration is complete, luminaire is ready for operation with its new software version. Verify software version at luminaire: Step 1. At Menu Display, press [Menu]. Step 2. Press [Up] / [Down] arrows until Fixture appears. Press [Enter]. Step 3. Press [Up] / [Down] arrows until Version appears. Press [Enter]. The first half of the version will be displayed as a date (MM.DD.YY). For example, (March 18, 2003). Press [Up] / [Down] arrows to display second half of version. This will be displayed as a time (HH:MM). For example, 16: February

60 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Notes February

61 CHAPTER 4. Menu System This chapter contains instructions for operating the luminaire using the Menu Display feature. Menu Operation Menu Functions Self Tests February

62 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Menu Operation What Is the Menu System? The menu system is a programmable set of commands used to configure, address, operate, and test the luminaire. The menu system is controlled at the Menu Display available at the yoke leg. The menu system has seven main functions which are referred to as 1st level. Within these main functions, there can be up to four additional subfunctions (levels 2 thru 5), making five total levels. Menu Display Menu Controls Operation The menu system is controlled by four buttons. These buttons function as follows: [Menu] button Displays the menu, or if at first level, the current address. Can also enable menu to exit a menu level. [Enter] button Selects the current menu option or stores current data value. Address [Up] arrow Scrolls menu options upward or increases MENU ENTER current data value. [Down] arrow Scrolls menu options downward or decreases current data value. To enter the menu system, first press [Menu]. The functions displayed will be 1st level functions. Scroll through the 1st level functions by pressing [Up] / [Down] arrows. Once the desired function appears in the display, Press to show menu, or if at first level, the current address. press [Enter]. You are now at the 2nd level. Once again, press the [Up] / [Down] arrows to scroll through 2nd level functions. Press [Enter] to access 3rd level functions and so forth. When the highest level for the function is reached, [Up] / [Down] arrows can be pressed to select a value or select a toggle activation such as ON/OFF. Press [Enter] to store the value or select an action. For example, the Address function has one sub-level: DMX. This 2nd level menu allow access to a 3rd level, which is a value. The Address function is a 3-level menu. 1st Level 2nd Level 3rd Level Down / Decrease Up / Increase LCD Display Press to select current menu option or current data value. Menu Default State Address DMX XXX The menu display s default state during normal operation is to display the address. After 10 seconds of inactivity at the display, it will change to this default state February

63 MENU SYSTEM : MENU OPERATION 4 After 5 minutes of inactivity, the menu display will switch to its off state. Menu Shortcuts A few button combinations are provided as shortcuts for frequently used menu functions. These are as follows: Lamp On - Press and hold [Up], then press [Enter]. (Arc and CD models only.) Lamp Off - Press and hold [Down], then press [Enter]. (Arc and CD models only.) Recalibrate - Press and hold [Up], then press [Menu]. Interrupt Calibration - Press [Menu] at Power up. (See Program Starting Address Without Calibrating on page 24 for more information.) February

64 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Menu Functions Menu System Overview The following is a graphic representation of the entire menu system. Address DMX value Setup Config Lamp* Power ON OFF Power Up Lamp OFF Cal ON Lamp ON LampHour # of hours ResetHrs OK? Pan/Tilt Movement Enable Display 30Sec 5 Min 10 Min ON Disable ResetDef OK? DMX Fixture LampType Shutter? Clear Data Chan XXX data Pan/Tilt Swap Inv Pan ON OFF ON OFF Inv Tilt ON OFF Status Re-Cal Model Lum Id Version Fixt Hrs Download Arc Incand CD Yes No OK? scrolls errors or displays OK OK? VL1XXX XXXXXXXX (MM/DD/YY) time # of hours on OK? Manual Test Pan Tilt Dimmer* Blue Amber Magenta Diffusn Rot Gobo Index Edge Zoom Beam Rot Shut Frame 1A Frame 1B Frame 2A Frame 2B Frame 3A Frame 3B Frame 4A Frame 4B ALL Pan/Tilt Dimmer* Blue Amber Magenta ColorMix Diffusn Rot Gobo Edge Zoom Beam Shutter Rot Shut Lamp Encoder Sensor value value value value value value value value value value value value value value value value value value value value value RUN TEST RUN TEST RUN TEST RUN TEST RUN TEST RUN TEST RUN TEST RUN TEST RUN TEST RUN TEST RUN TEST RUN TEST RUN TEST RUN TEST RUN TEST Pan Tilt Pan Tilt Rot Gobo GoboIndx value value STST STST STST STST * (Arc & CD models only) February

65 MENU SYSTEM : MENU FUNCTIONS 4 Menu System Function Chart 1st Level 2nd Level 3rd Level 4th Level 5thLevel Address DMX DMX Address XXX Address value Setup LampType Arc Incand CD Config System Configuration DMX DMX Mode and Data Shutter? LAMP Lamp Options (Arc & CD Models Only) Yes No Power Lamp Power ON (default) OFF Power Up Lamp Power-up State Lamp OFF Lamp Off Cal ON Lamp On After Calibration Lamp ON Lamp On (default) LampHour Lamp Hours Used XXXX Cumulative # of Operation Hours (Not editable) ResetHrs Reset Lamp Hour and Lamp Strike Counters Pan/Tilt Pan and Tilt Options Movement Position Recovery Enable Enable Disable Disable Display Display Illumination 30s OFF in 30 seconds 5M OFF in 5 minutes (default) 10M OFF in 10 minutes ON ON indefinitely ResetDef Reset Default Values OK? Clear Clear Stored Parameters and Re-Cal OK? OK? DATA Chan XXX DMX Channel XXXX Data Pan/Tilt Pan and Tilt Options Swap Swap Pan & Tilt ON OFF InvP Invert Pan ON OFF InvT Invert Tilt ON OFF February

66 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL 1st Level 2nd Level 3rd Level 4th Level 5thLevel Fixture Status Status/Error Display Scrolls error messages or displays OK Manual Manual Commands Re-Cal Recalibrate Model Luminaire Model Type Lum Id Luminaire ID OK? VL1100XX Model Type XXXXXXXX Luminaire ID Number Version Version XX/XX/XX MM/DD/YY (Page 1) XXX Time (in 6 min intervals) (Page 2) Fixt Hrs Fixture Hours Download Pan Pan Tilt Tilt Dimmer Dimmer (Arc & CD Only) Blue Blue Amber Amber Magenta Magenta Diffusn Diffusion Rot Gobo Rotating Gobo Index Rotating Gobo Index Edge Edge Zoom Zoom Beam Beam-size Iris (If Beam-Size Iris Accessory) Rot Shut Rotating Frame (Shutter) (If Shutter Accessory) Frame 1A (If Shutter Accessory) Frame 1B (If Shutter Accessory) Frame 2A (If Shutter Accessory) Frame 2B (If Shutter Accessory) Frame 3A (If Shutter Accessory) Frame 3B (If Shutter Accessory) Frame 4A (If Shutter Accessory) Frame 4B (If Shutter Accessory) XXXX # Hours On OK? XXXX Data XXXX Data XXX Data XXX Data XXX Data XXX Data XXX Data XXX Data XXXX Data XXX Data XXX Data XXX Data XXX Data XXX Data XXX Data XXX Data XXX Data XXX Data XXX Data XXX Data XXX Data February

67 MENU SYSTEM : MENU FUNCTIONS 4 1st Level 2nd Level 3rd Level 4th Level 5thLevel Test System Test ALL Test All Motors RUN TEST Run-Test in Progress Press [Menu] to Pan/Tilt RUN TEST Run-Test in Progress stop tests Dimmer (Arc Only) RUN TEST Run-Test in Progress Blue RUN TEST Run-Test in Progress Amber RUN TEST Run-Test in Progress Magenta RUN TEST Run-Test in Progress ColorMix Blue, Amber, Magenta test RUN TEST Run-Test in Progress Diffusn Diffusion Test RUN TEST Run-Test in Progress Rot Gobo Rotating Gobo Test RUN TEST Run-Test in Progress Edge RUN TEST Run-Test in Progress Zoom RUN TEST Run-Test in Progress Beam (If Beam-Size Iris Accessory) RUN TEST Run-Test in Progress Shutter (If Shutter Accessory) RUN TEST Run-Test in Progress Rot Shut (If Shutter Accessory) RUN TEST Run-Test in Progress Lamp Disables Pan/Tilt and executes Home position. Lamp 1 Run-Test in Progress Lamp 2 (inserts magenta to 30%) Run-Test in Progress Encoder Encoders Pan Pan Encoder XXXX Data Tilt Tilt Encoder XXXX Data Sensor Sensors Pan COT Sensor STST Sensor Test in Progress Tilt COT Sensor Rot Gobo Gobo Select EOT Sensor GoboIndx Gobo Index EOT Sensor STST Sensor Test in Progress STST Sensor Test in Progress STST Sensor Test in Progress PASS/FAIL PASS/FAIL PASS/FAIL PASS/FAIL February

68 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Menu Function Definitions For easy reference, each possible menu item is listed alphabetically in the first column by its display abbreviation. The second column follows with a definition of the abbreviation and then a third column provides an explanation of its purpose and function. Display Definition Purpose 10 Min 10 Minutes Sets Menu Display to automatically shut off after 10 minutes of non-use. 30 Sec 30 Seconds Sets Menu Display to automatically shut off after 30 seconds of non-use. 5 Min 5 Minutes Sets Menu Display to automatically shut off after 5 minutes of non-use. Address DMX Address Accesses function for setting luminaire DMX starting address. ALL All Motors Tests all internal motors. Amber Amber Specifies Amber for manual control (Manual) or test Amber functions (Test). Arc Arc Specifies luminaire as having an arc lamp source. Blue Blue Specifies Blue for manual control (Manual) or tests Blue functions (Test). Cal ON Calibration On Configures arc luminaire so that lamp will strike after calibration procedure is complete. CD VL1100CD Model Sets menu option to VL1100CD luminaire (VL1100CD models only) Chan XXX DMX Channel Specifies DMX channel for display of current data value. Clear Clear Clears stored parameters and re-calibrates luminaire. ColorMix Color Mixer Tests color mixing mechanism. Config System Configuration Accesses functions for setting lamp, pan/tilt, and Menu Display options. Also accesses lamp information such as number of strikes, and hours used, along with their respective reset function. Data DMX Data Accesses function for displaying DMX data by channel number. Diffusn Diffusion Specifies manual control of Diffusion (Manual) or tests Diffusion functions (Test). Dimmer Dimmer Specifies dimmer mechanism for manual control (Manual) or tests dimmer/ strobe functions (Test). Disable Disable Disables a function. Display Display Illumination Accesses options for Menu Display on and off times. DMX DMX Sets starting address for DMX systems. Edge Edge Function Specifies edge function for manual control (Manual) or for testing (Test). Enable Enable Enables a function. Encoder Encoders Accesses encoder choices for diagnostic testing. FAIL Test Fail Indicates that sensor test has failed. Fixt Hrs Fixture Hours Displays total number of hours luminaire has been powered on. Fixture Fixture Access luminaire specification information such as model, serial number, software version, along with status information. Frame 1A - Frame 4B Frame Side Specifies shutter frames 1A, 1B, 2A, 2B, 3A, 3B, 4A or 4B for manual control depending on which one is selected at the Manual Commands menu. GoboIndx Gobo Index Specifies gobo index EOT sensor for testing. Incand Incandescent Specifies luminaire as having an incandescent lamp source. Index Gobo Index Specifies rotating gobo index for manual control. Inv Pan Invert Pan Reverses pan action for special focus requirements February

69 MENU SYSTEM : MENU FUNCTIONS 4 Display Definition Purpose Inv Tilt Invert Tilt Reverses tilt action for special focus requirements. Lamp Lamp Accesses lamp power up options and information (Config). Lamp 1 Lamp Specifies test lamp operation (Test). Lamp 2 Lamp Specifies test lamp operation (Test). Inserts magenta to 30%. Lamp OFF Lamp is Off Configures arc luminaire so that lamp will not strike upon power up. Lamp ON Lamp is On Configures arc luminaire so that lamp will strike upon power up. LampHour Lamp Hours Displays total number of lamp operating hours. LampType Lamp Type Accesses menu item for configuring luminaire for arc or incandescent source. Lum Id Luminaire ID Displays unique luminaire ID number. Magenta Magenta Specifies manual control of Magenta (Manual) or test Magenta functions (Test). Manual Manual Commands Accesses functions for controlling luminaire mechanisms and timing by entry of an absolute data value. Model Model Displays model number of luminaire. For example, VL1100TS. Movement Movement Enables and disables pan and tilt movement and auto-correction. No No Specifies that the luminaire does not contain the shutter accessory. OFF Off Turns off a function. OK Okay Calibration has completed and no errors have occurred. OK? Okay? Prompt for pressing [Enter] before an action is executed. ON On Indefinitely Sets Menu Display to stay on until programmed otherwise (Display) or turns on a function. Pan Pan Specifies pan function for manual control (Manual) or pan encoder for testing (Test). Pan/Tilt Pan/Tilt Accesses pan and tilt options for DMX function, system configuration, and testing. PASS Test Pass Indicates that sensor test has passed. Power Lamp Power Accesses function to turn lamp on or off. PROG Programming Currently programming the new version of software. Re-Cal Recalibrate Currently executing calibration or recalibrates luminaire. ResetDef Reset Default Resets default system configuration values. ResetHrs Reset Lamp Info Resets lamp hour and lamp strike counters. For use when new lamp is installed. Rot Gobo Rotating Gobo Specifies rotating gobo for manual control (Manual) or gobo select EOT sensor for testing (Test). Rot Shut Rotating Shutter Specifies shutter mechanism rotating function for manual control (Manual) or for testing (Test). RUN TEST Run-Test Indicates that a system mechanism test is in progress. Sensor Sensors Accesses sensor choices for diagnostic testing. Setup Setup Accesses lamp type and shutter operation settings. Shutter Shutter Specifies shutter mechanism for testing. Shutter? Shutter Accesses menu item for configuring luminaire for shutter operation. Status Status/Error Display Allows scrolling through error list or displays OK if no errors. STST Sensor Test Indicates that a system sensor test is in progress. Test System Tests Accesses diagnostic tests for internal mechanisms. Tilt Tilt Specifies tilt function for manual control (Manual) or tilt encoder for testing (Test) February

70 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Display Definition Purpose Version Version Displays current software version (Date and Time in two pages). Yes Yes Specifies that the luminaire contains the shutter accessory. Zoom Zoom Function Specifies zoom function for manual control (Manual) or for testing (Test) February

71 MENU SYSTEM : SELF TESTS 4 Self Tests Running Parameter Tests The luminaire is capable of running self tests by using the TEST menu functions. Note: If a DMX data stream is present on the luminaire s DMX input connector, Self Test and Manual control is overwritten by the DMX command protocol and neither (Self Test and Manual) will operate. When running tests on multiple luminaires, a loopback connector is required at the master luminaire (first in link) and a male termination connector is required at the last luminaire in the link. Refer to page 13 for more information regarding the construction of these connectors. Note: After 10 seconds of inactivity, the menu display will change to the default state showing the address. To connect luminaires for simultaneous testing: Step 1. At first luminaire in link, install loopback connector into DATA IN XLR connector. Step 2. At last luminaire, install DMX termination connector into DATA THRU XLR connector. Step 3. At master luminaire Menu Display, press [Menu]. First luminaire containing software version to download Luminaire 1 requiring update Luminaire 2 requiring update Data Thru Data Thru Loopback Connector DMX Termination Connector Figure 4-1: Hardware Setup To run tests: Step 1. Press [Menu]. Step 2. Press [Up] / [Down] arrows until Test appears. Press [Enter]. Step 3. Use [Up] / [Down] arrows to select a parameter to test. Refer to Menu System Function Chart on page 49 for a complete list of test parameters which can be chosen. Step 4. Press [Enter] to run test. Step 5. Press [Menu] to stop test at any time February

72 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Movement Disable The Movement option allows pan and tilt to be disabled so that the luminaire can be placed in any position for testing without movement occurring. In order to regain full control of the luminaire, Movement will need to be enabled after testing. Note: When using the Movement option, pan and tilt will be disabled for all the luminaires that are linked. To set movement option: Step Step Step Step Step 1. Press [Menu]. 2. Press [Up] / [Down] arrows until Config appears. Press [Enter]. 3. Press [Up] / [Down] arrows until Pan/Tilt appears. Press [Enter]. 4. Movement will be displayed. Press [Enter]. 5. Use [Up] / [Down] arrows to select Enable or Disable. Press [Enter] to select February

73 APPENDIX A. Troubleshooting and Maintenance This appendix provides instructions for troubleshooting and performing routine maintenance which may be necessary during the life of the luminaire. Troubleshooting Routine Maintenance WARNING: All routine maintenance procedures are to be performed with power completely removed from the luminaire. Never remove protective covers when luminaire is powered. Wear appropriate protective eye wear and gloves when servicing the fixture. All service and maintenance, other than described herein should be performed by an Authorized VARI LITE Dealer or Service Center. WARNING: DO NOT connect or disconnect energized power cable at fixture (under load). Turn off circuit breaker (or completely de-energize circuit) before connecting or disconnecting power cable at fixture. Power is only removed from the fixture by disconnecting power cable from source or turning off source circuit breaker February

74 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Troubleshooting Error Messages If a problem occurs during luminaire calibration, at the end of the calibration sequence the Menu Display will cycle through any applicable error message(s) until the end of the list is reached. To review the error messages again, it will be necessary to access them using the Status function. To access error messages: Step 1. Press [Menu]. Step 2. Press [Up] / [Down] arrows until Fixture appears. Press [Enter]. Step 3. Press [Up]/ [Down] arrows to access Status. Press [Enter]. (Display will now scroll through any error messages or display OK if no errors.) Table A-1: Error Messages Display OK Pan/No Sens Pan/Encoder/Fail Tilt/No Sens Tilt/Encoder/Fail Index/No Sens Rot Gobo/No Sens Lamp/Strike/Fail Message... No Errors Found Pan sensor not found. Pan encoder failure. Tilt sensor not found. Tilt encoder failure. Gobo Index sensor not found. Rotating Gobo sensor not found. Lamp strike failure February

75 TROUBLESHOOTING AND MAINTENANCE A Troubleshooting Guide If a problem is suspected, first try recalibrating the luminaire to prompt an error message. Table A-2 below provides possible causes and remedies for various error messages and/or symptoms. CAUTION: Some troubleshooting is included for reference only. Performing remedies marked by gray areas will void product warranty. Refer to the Vari-Lite Limited Warranty card included with the product. Table A-2: Troubleshooting Guide Error Display Description Possible Cause and Remedy Pan/No Sens Pan Sensor Not Found EOT flag attached to large pulley is not engaging the EOT sensor - Ensure flag is attached to the large pulley - Ensure that flag passes through the sensor at a depth sufficient to engage the sensor beam Pan belt disconnected, extremely loose or not installed properly - Properly install belt between pan motor and large pulley Pan/Encoder/Fail Pan Encoder Failure Main board pan/tilt connector (J9) disconnected - Connect main board pan/tilt connector (J9) Pan motor disconnected - Connect pan motor power Encoder faulty - Replace pan end-of-travel/encoder sensor assembly TILT NO SENS Tilt Sensor Not Found EOT flag attached to large pulley is not engaging the EOT sensor - Ensure flag is attached to the large pulley - Ensure that flag passes through the sensor at a depth sufficient to engage the sensor beam Tilt belt disconnected, extremely loose or not installed properly - Properly install belt between tilt motor and large pulley Tilt/Encoder/Fail Tilt Encoder Failure Main board pan/tilt connector (J9) disconnected - Connect main board pan/tilt connector (J9) Tilt motor disconnected - Connect tilt motor power Encoder faulty - Replace pan end-of-travel/encoder sensor assembly Lamp/Strike/Fail Lamp Strike Failure* Lamp failed to strike after repeated attempts - Replace lamp Note: *The nature of the CDM lamp used in the VL1100CD ERS Luminaire prevents it from restriking when it is hot after use. It takes approximately 15 minutes for the lamp to cool enough to restrike February

76 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Routine Maintenance Cleaning Optical Lenses and Gobos WARNING: Remove power from luminaire before performing maintenance. The front lens and gobos may require cleaning after extended use. Use only isopropyl alcohol, along with a soft, lint-free cloth to clean glass components. To access gobos, refer to procedure below. Rotating Gobo Replacement WARNING: Remove power from luminaire before performing maintenance. Gobos may be HOT after operation. Allow to cool before replacing. To replace a rotating gobo: Step 1. Remove power from luminaire. Step 2. At either side of head assembly, press in front cover latch and pull cover straight back until stopped by tether. Step 3. Rotate gobo wheel until required gobo position is accessible at finger access cutout. Step 4. Rotate gobo gear until open end of carrier is upward. CAUTION: Do not touch gobos with bare fingers. Wear cotton gloves or other covering while replacing. Clean with isopropyl alcohol and soft, lint-free cloth if required. CAUTION: Do not pull metal spring clip carrier back too far or it will not close properly. Step Step 5. If applicable, carefully pull current gobo up and out of carrier. Gobo can be easily scratched on sides of carrier if not careful. 6. Carefully install new gobo, orienting side marked "This Edge In" toward center of gobo wheel and side marked "Lamp Side" (mirror finish) toward lamp. Gobo can be easily scratched on sides of carrier if not careful. Ensure gobo is firmly set in carrier grooves February

77 TROUBLESHOOTING AND MAINTENANCE A Step 7. Re-install front cover. CAUTION: Gobo MUST be oriented with the mirrored side towards the luminaire s lamp. If not oriented properly, gobo will break. Be careful not to scratch gobo on side of carrier when installing. Inside Edge - orient toward center of wheel Lamp Side (mirrored) - orient toward luminaire lamp Closed End Rotate until open end of carrier is up Gear Open End Front Cover Gobo Positions Sensor 2 1 open Gobo (black side) Latch Gobo Wheel Front View 4 Lamp End Rotating Gobo Wheel CAUTION: Be careful not to pull metal spring clip carrier back too far or it will not close properly. Center of Wheel Figure A-1: Rotating Gobo Replacement/Cleaning February

78 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Lamp Replacement For lamp replacement procedure, refer to Installation Procedures on page February

79 APPENDIX B. Technical Specifications Mechanical Zoom Optics Continuously variable field angle in imaging range from 19 to 36, super zoom angles to 70 is programmable over a timed range of 2 seconds to 20 minutes. Color Mixing System A fully cross-fading CYM color system. All motors utilize a noise reducing, 50kHz. drive system that quiets operation during movement and also while static. Diffusion Field or gobo image can be continuously and smoothly diffused to wash. Intensity Control A coated glass dimmer wheel provides full-field dimming designed for smooth timed fades. Rotating Gobo Wheel Six position rotating gobo wheel with a central bearing system, five rotatable and indexable gobo positions plus open. (Patterns are not included with the fixture. Use of glass or metal patterns is acceptable.) Shutter (Framing Models) Four-blade system can frame and crop beam field and gobos. Each individual shutter is capable of translating to beam center while also rotating ±35. Entire shutter rotates ±45. Beam Size Control (Iris Models) In addition to the zoom optics, a mechanical iris provides continuous beam size control for both rapid changes and smooth timed beam angle changes. Pan and Tilt Smooth, timed continuous motion using three-phase, ultra quiet stepper motors with encoder correction. Pan range is 540 ; tilt is 270. Resolution is 0.3. Unit will calibrate to support close hangs (yoke-to-yoke). Optical Source 315W CDM Lamp. Color Temp: 3200K, CRI: 95 Output: >8,000 Lumens, Rated Life: 8,000 Hours February

80 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Reflector Precision glass reflector with dichroic cold mirror coating. Operational Power Requirements 3 to 6 Amps depending upon input voltage VAC 50/60 Hz. Operational Temperature -20 to 122 F (-29 to 50 C) Cooling Free convection cooling when hung. Floor mounted units and extreme ambient temperatures activate a low-noise, forced-air cooling system. Control Compatible with a wide variety of DMX512 consoles. Mounting Position All models can be mounted and operated in any orientation. Weight 74.9 lbs (34 kg) Spacing Hangs on 26.5 in. (67.3 cm) centers. 26.5" (67.3cm) 17.5" (44.5cm) 35.5" (90.2cm) 26" (66cm) February

81 TROUBLESHOOTING AND MAINTENANCE B Photometric VL1100CD ERS Luminaire CDM Lamp (All data taken with a seasoned light source at 20 hours of life.) FIELD ANGLE (degrees) FIELD DIAMETER TN* BEAM ANGLE (degrees) BEAM DIAMETER TN* CANDELA (cd) , , , (Super Zoom) ,400 * Multiply throw distance by Tn to determine coverage. To calculate Illuminance (I) at a specific distance (D): I = cd D February

82 VARI LITE - VL1100CD ERS LUMINAIRE USER S MANUAL Notes February

83

84 Vari-Lite Petal Street Dallas, Texas USA VARI-LITE Vari-Lite, a Philips group company. All Rights Reserved.