LoadMan LM310 Reference Guide For

Transcription

1 LadMan LM310 Reference Guide Fr Cart Lifter Weigh-In-Mtin Rear Lader Refuse Trucks Revisin Creative Micrsystems, Inc SE Rentn Issaquah Rad Rentn, WA Phne: LOADMAN LadMan is a registered trademark f Creative Micrsystems Inc. Cpyright 2013 Creative Micrsystems All Rights Reserved

2 ii

3 SAFETY WARNING Using this system while perating a mtr vehicle may be distracting, dangerus, r prhibited. Operatr remains respnsible fr safe travel, shuld bey laws and regulatins, and shuld exercise gd judgment at all times. Failure t pay full attentin t the peratin f the vehicle may cause an accident resulting in serius cnsequences. Yu assume sle respnsibility and risk fr using this system. iii

4 iv

5 Table f Cntents TABLE OF CONTENTS SAFETY WARNING III INTRODUCTION 7 OPERATIONAL BASICS 11 Pwer LadMan Frnt Panel and Display LadMan Operating Mdes Measurement Units English / Metric Intrductin t the PROGRAM FUNCTION Display Cnnectivity & Cmmunicatins Intrductin t LadMan Lad Manager Sftware NORMAL OPERATING MODE 23 Weight and Infrmatin Displays Rute Infrmatin Displays PROGRAM FUNCTION Displays SETUP & CALIBRATION MODE 37 Basic Navigatin Setup & Calibratin Cmmands INITIAL STARTUP AND CALIBRATION Verify Wiring Pwer On Verify Arm Angle Sensr Verify Cart Lifter Lad Cells Respnd Crrectly Calibrate Cart Lifter Arm Angle Verify Angle Measurements Respnd Crrectly Verify Weigh-In-Mtin Respnse v

6 Table f Cntents 8. Calibrate System Calibrate Cart Lifter System Under Lad TROUBLESHOOTING GUIDE NO ARM SENSOR! NO LEFTCART SIG! NO LEFTCART SIG! Lad Measurements Inaccurate COLLECTING LOAD DATA 81 Out-f-Sequence r Unplanned Cllectins WIRING DIAGRAM 85 APPENDIX A ERROR MESSAGES 86 APPENDIX B SETUP & CONFIGURATION COMMAND TREE 87 APPENDIX C CELL STATE CODES AND DESCRIPTIONS 91 APPENDIX D DOWNLOADING LOADMAN METER SOFTWARE 93 Cnnecting PC/Laptp t LM INDEX 103 vi

7 Intrductin INTRODUCTION The LadMan LM310 is a precisin instrument capable f running and cntrlling many different vehicle weight measurement applicatins. The Applicatin Sftware dcumented in this manual supprts LadMan s Weigh-In- Mtin Cart Lifter Weighing Systems. These Weighing Systems are usually munted n vehicles that weigh residential carts in mtin as they are picked up, dumped, and lwered t the grund. The LadMan system is cmpletely autmatic and the driver/peratr des nt need t press any buttns r take any actins t btain a weight reading. The 16 character display prvides all the infrmatin needed t understand the status f the weighing system. Fr example, the meter autmatically prvides the fllwing instructin displays during the weigh-in-mtin prcess: READY TO WEIGH WEIGHING LOAD GROSS WEIGHT DUMP LOAD WEIGHING TARE NET WEIGHT TRUCK The cart lifter arm is belw the start f the weighing windw and the system is ready t begin weighing. Message while cart is lifted up thrugh the weighing windw. Displays weight f the cart and its grss lad weight. Weighing is cmplete and lad is ready t dump. The grss lad weight measured ging up is still displayed. Measuring the empty cart weight while cart is cming dwn. Displays the cmputed net weight f the dumped material. Displays the accumulated lad net weight that has been dumped int the truck. LM310 An nbard in-cab-meter fr displaying weight, rute and system infrmatin. ARM310 A cmputer based arm weigh-in-mtin assembly munted n 7

8 Intrductin the arm f the cart lifter (blted t the lift arm f the cart lifter). CART A cart weigh-in-mtin assembly munted between the tw munting plates which supprt the cart lifter assembly. Figure 1. ARM310 Cnnected with CART310 The CART310 weigh-in-mtin assembly cnverts the sensitive analg data signals frm the tw cart lifter ladcells t digital, using a precisin digital t analg encder called a CanCder. It als receives the angular psitin f the cart lifter arms measured by the ARM310 alng with speed; cnverts the infrmatin t digital, and transmits the data up the LM310 meter fr display and prcessing. The ARM310 weigh-in-mtin assembly als cntains an angle sensr; s the weighing system nt nly knws the psitin and speed f the cart lifter, but als the angular psitin and speed f the lift mechanism at all times. The CART310 cart bx cmputer gathers the weight measurement frm the cart lifter ladcells, the lift arms angular psitin and speed frm the ARM310. It then prcesses this infrmatin t determine the weight f the cart plus its cntents while ging up (grss weight). Then, in the same manner, measures the tare weight f the cart ging dwn. The difference between these tw weights determines the net weight f the material that was dumped int the truck (NET). All f this infrmatin is transmitted t the LM310 in-cab meter and displayed t the driver/peratr. The lad data recrd can wirelessly transmit t LadMan s 8

9 Intrductin Lad Management Sftware if the data cllectin sftware is perating in the back ffice. LadMan's Lad Management Sftware allws remte tracking f trucks, drivers, custmers, rutes and prducts by accunt r jb. Rute lists are created with the sftware and dwnladed t the LadMan meter. Any recrded lad data and/r GPS psitin data in LadMan s data cllectin memry will be autmatically transferred t the Lad Management Sftware - withut any prmpting r interventin frm the driver whenever a wireless mdem r wireless Bluetth cnnectin is established between the truck s LM310 cmputer and the back ffice sftware. 9

10 Intrductin 10

11 Operatinal Basics OPERATIONAL BASICS This sectin will intrduce the peratinal basics f the LM310 LadMan Meter. Anyne new t the use f the LadMan Meter shuld first read this sectin t becme familiar with: Frnt panel display Keypad definitins and use Basic navigatin Prgramming basics Cnnectivity & Cmmunicatins LadMan Lad Manager Sftware Pwer Cnnecting pwer at the rear panel causes LadMan t pwer n, displaying the message LOADMAN, fllwed by PROG VERSION X.X. The Prgram Versin number X.X represents the applicatin sftware versin and aids in tracking sftware updates. With pwer n, and within any perating mde, mmentarily pressing the POWER buttn causes LadMan t briefly display the GOODBYE! message. When pwer is applied, the message CYCLE ARMS may appear if the cart lifter is nt in the READY TO WEIGH psitin. Repsitining the Cart Lifter Arm t the nrmal Ready t Weigh psitin will return the display t READY TO WEIGH. 11

12 Operatinal Basics LadMan Frnt Panel and Display As shwn in Figure 2, the LadMan LCD display has a 16 character alphanumeric field fr displaying peratinal messages as well as setup and calibratin instructins. There are 6 push-buttns used fr pwer, prgramming and display selectin. PROGRAM Keys Figure 2. LadMan LM310 Meter Frnt View These PROGRAM keys are used t enter a cmmand (like ZERO TRUCK), print a lad recrd (PRINT LAST LOAD), change a prgrammable number (like setting the TRUCK tare weight in Setup & Calibratin), r setting the Date and Time. If a selected display is prgrammable, pressing the PROGRAM key will initiate a flashing cursr in the display, signifying that LadMan has entered the Prgram Mde. Fr prgrammable displays, use the PROGRAM key t mve the flashing cursr left t the next prgrammable digit/item in the display. Once the flashing cursr is psitined ver the item t be changed, use the PROGRAM key t increase/bump the digit/item t its next value. Cntinue t use the / PROGRAM keys until the display has been prgrammed t the crrect value. The SET PROGRAM key will execute the cmmand and save any changes made t the display. 12

13 Operatinal Basics LadMan will take NO actin n selectins and/r changes until the SET PROGRAM key is pressed. And, if a selected display is nt prgrammable, pressing any f the PROGRAM grup f keys will have n effect. SELECT Keys The SELECT keys are used t manually scrll thrugh any f the currently available vehicle weight displays and rute infrmatin. These keys are als fr scrlling thrugh setup & calibratin cmmand ptins. The SELECT key will sequence frward thrugh a grup f displays. The SELECT key will sequence in reverse thrugh a grup f displays. Weight and Message Display Any weight infrmatin, rute infrmatin r status message infrmatin shwn n the 16 character display will depend n the verall setup and cnfiguratin f the LadMan Meter (discussed in later sectins). LadMan Operating Mdes LadMan has tw distinct perating mdes: the Nrmal Operating Mde and Setup & Calibratin Mde. Intrductin t Nrmal Operating Mde At pwer n, LadMan enters the Nrmal Operating Mde which prvides the main peratinal, messaging and status infrmatin fr the LadMan weight and rute applicatins. Table 1. Nrmal Operating Mde Display cntains a list f display messages that can be manually accessed using the / SELECT keys, r autmatically cycle displayed. Intrductin t Setup & Calibratin Mde LadMan s Setup & Calibratin Mde prvides the peratr the capability t prgram advanced functinality, chse ptinal infrmatin displays, enable cmmunicatins, and t setup and calibrate a truck s cnfiguratin. The tp level cmmand ptins are summarized intable 6, and detailed prgramming f these ptins will be discussed in the sectin titled Setup & Calibratin Mde later in this guide. Als, a detailed cmmand tree is lcated in Appendix B 13

14 Operatinal Basics Setup & Cnfiguratin Cmmand Tree. Activating Setup & Calibratin Mde w/security OFF Cntinually depress the POWER buttn, thrugh the GOODBYE! message, and until the LOADMAN SETUP message is displayed. The first setup & calibratin categry displayed is SET ZERO?---->NO. Activating Setup & Calibratin Mde w/security ON Cntinually depress the POWER buttn. The messages GOODBYE! and ENTER PASS CODE! will display. At the prmpt, PASS CODE 0, use the / PROGRAM keys t prgram the security cde t 123 and save the cde with the SET PROGRAM key. If crrect, LadMan displays the message, LOADMAN SETUP. And the first setup & calibratin categry displayed is SET ZERO?---->NO. If the security cde is NOT crrect, the errr message, SECURITY FAILED is displayed, and the Setup & Calibratin mde cannt be accessed. When finished with any f the setup categries and t return LadMan t the nrmal perating mde: Press the SELECT key until EXIT SETUP?-->NO is displayed. Then press PROGRAM key t display EXIT SETUP?-->YES. Finally, press the SET PROGRAM key. LadMan will nw return t the nrmal perating mde Infrmatin Display. 14

15 Operatinal Basics Infrmatin Display Weight Displays Table 1. Nrmal Operating Mde Display READY TO WEIGH WEIGHING LOAD GROSS LOAD / DUMP LOWER ARMS NET RECORDING LOAD LAST TRUCK TARGET Use the SELECT key t sequence frward thrugh available displays Rute Infrmatin Displays Date & Time LOAD NAME LOAD ACCOUNT # STOP # PRODUCT NAME EVENT NAME ASSET NAME DATE & TIME Use the SELECT key t sequence in reverse thrugh available displays 15

16 Operatinal Basics SET ZERO SET SPAN SET TARE INSTALL Table 2. Setup & Calibratin Cmmands Calibrates the Cart Lifter Arm Angle sensr t zer. Calibrates the truck s lad f material t readings taken frm anther scale. Sets the empty weight f the vehicle. Prvides the capability t setup and/r change the perating cnfiguratin f LadMan. SELECT Sequence frward thrugh available displays / PROGRAM Keys fr prgramming values and cmmand entry SET DEFAULTS ERASE DATA TROUBLESHOOT Returns all settings t factry default settings. Permanently erases all data in LadMan s data cllectin memry. Prvides detailed angle sensr, ladcell, cmmunicatins and ther LadMan infrmatin that can be useful fr islating issues. SET PROGRAM T enter/activate cmmand r value SELECT Sequence in reverse thrugh available displays Measurement Units English / Metric The LadMan meter cmes precnfigured at the factry t display weight measurements in English r Metric units. Thrughut this manual, English units will be used when explaining cmmands and presenting examples, but everything presented in this manual is valid fr bth English and Metric cnfigured meters. Metric Units Setting Kilgrams/KG T cnfigure LadMan t display weights in metric units, kilgrams/kg: 16

17 Operatinal Basics First enter the Setup & Calibratin Mde as just described abve. Use the SELECT key t lcate INSTALL?----->NO. Press PROGRAM t chse YES ; then SET. Use the / SELECT keys t lcate SET DISPLAYS->NO. Press PROGRAM t chse YES ; then SET. Nw use the PROGRAM and SET PROGRAM keys t chse and set DISPLAY UNITS=KG. This exercise intrduced the prgramming and cnfiguratin prcess. Mre prgramming and cnfiguratin will be cvered later in this manual. But fr nw, when finished prgramming and t return t the nrmal perating mde, press SELECT t lcate EXIT SETUP? ; chse YES with the PROGRAM key; and save/exit by pressing the SET PROGRAM key. Intrductin t the PROGRAM FUNCTION Display Use the PROGRAM FUNCTION display t access and activate ne f the cmmand ptins listed in Table 3. Table 3. PROGRAM FUNCTION Cmmands SHOW NET SHOW GROSS PRINT LAST LOAD ZERO CART LOAD CYCLE DISPLAY ZERO TRUCK Set display t shw Truck NET weight peratin. Set display fr Truck GROSS weight peratin. Prints the mst recent lad data measured t a precnfigured printer Resets the cart lifter lad cells t read zer Initiates the autmatic display cycle f weight infrmatin and status messages Zers the accumulated truck lad TOTAL and prvides ptin t capture a landfill dump weight Use the / SELECT keys t lcate the PROGRAM FUNCTION display. Use the / PROGRAM keys t sequence thrugh available prgram ptins. = frward = reverse Use the SET PROGRAM key t activate cmmand. 17

18 Operatinal Basics Either f the / PROGRAM keys will sequence thrugh the available PROGRAM FUNCTION displays, and nce an item is selected, the SET PROGRAM key will activate and save the selectin. LadMan will then return t the nrmal perating mde. While within any f the PROGRAM FUNCTION ptins, the / SELECT keys will abrt prgramming and return LadMan t manual display. Cnnectivity & Cmmunicatins RS232 Prts LadMan cmes standard with ne RS232 prt (9-pin female cnnectr) that is a available fr cnnecting peripheral devices like printers, barcde wands, etc. During setup and cnfiguratin, this is referred t as RS232 prt #1. RS232 Prt #2 (9-pin male cnnectr) is nt available fr cnnecting peripherals. This prt is dedicated t factry cnfiguratin and service diagnstics. Wireless Cmmunicatins The LadMan meter may cme equipped with an ptinal Bluetth wireless mdem, r a GSM cellular mdem. The mdem is used t cnnect and cmmunicate with LadMan s Lad Manager Sftware. If the Bluetth ptin is rdered, it will ccupy RS232 Prt #1. The 9-pin female cnnectr described abve will becme RS232 Prt #2. The GSM cellular mdem is separate dedicated antenna prt. The Lad Manager Sftware allws remte tracking f trucks & drivers, plus custmer accunts and rute lcatin; and exchanges the lad recrds and lcatin infrmatin thrugh ne f these mdems. GPS The LadMan meter may als cme equipped with an ptinal nbard GPS mdem and antenna. When recrded GPS crdinates are upladed int LadMan s Lad Manager Sftware, ffice management can use the latitude/lngitude crdinates t track truck rutes and aid with several ther advanced lcatin based functins frm the ffice. Refer t Figure 4. LadMan Cnnectivity Example. 18

19 Operatinal Basics Figure 3. LadMan Meter Rear View Figure 4. LadMan Cnnectivity Example 19

20 Operatinal Basics Intrductin t LadMan Lad Manager Sftware Figure 5. LadMan Lad Management Sftware LadMan's Lad Management Sftware allws remte tracking f trucks, drivers, custmers, rutes and prducts by accunt r jb. LadMan ffers tw versins f Lad Management Sftware: 1. Lad Management Clud Based Sftware - Database is in the clud and assessed thru standard internet enabled web brwsers 2. Lad Manger Desktp Sftware Database is at custmer s lcatin r n remte servers. Users use Windws t access all functins f the Lad Management sftware. Each fleet truck s data cllectin memry can be accessed by the sftware t gather: Rutes, vehicle ID, driver ID, and custmer accunts Prducts hauled r delivered - by accunt r jb Lad weights, lad sites and cmmdity 20

21 Operatinal Basics Truck and lad lcatins by GPS crdinates Events encuntered (Waste & Recycling) Time & date stamp n all lads This lad data is upladed t a back ffice management database, where lad data can be further studied by date, custmer, accunt, driver, etc., and even exprted t ppular accunting and spreadsheet prgrams. Visit ur LadMan website fr mre infrmatin abut LadMan Lad Manager and t view a vide demnstratin: 21

22 Operatinal Basics 22

23 Nrmal Operating Mde NORMAL OPERATING MODE At pwer n, LadMan enters the Nrmal Operating Mde, which prvides the main peratinal, messaging, and status infrmatin fr the LadMan weight and rute applicatins. The first display is the Infrmatin display that shws detailed lad and prcess infrmatin abut the in-mtin weighing cycle. This initial infrmatin display and ther weight, rute and prgramming displays are discussed in this chapter. Refer t Table 4. Table 4. Nrmal Operating Mde Display Infrmatin Display Weight Displays READY TO WEIGH WEIGHING LOAD GROSS LOAD / DUMP LOWER ARMS NET RECORDING LOAD LAST TRUCK TARGET Use the SELECT key t sequence frward thrugh available displays Rute Infrmatin Displays Date & Time LOAD NAME LOAD ACCOUNT # STOP # PRODUCT NAME EVENT NAME ASSET NAME DATE & TIME Use the SELECT key t sequence in reverse thrugh available displays 23

24 Nrmal Operating Mde Weight and Infrmatin Displays INFORMATION DISPLAY This display is where the weigh-in-mtin system nrmally perates. It has been set up t autmatically prvide the peratr all the instructins and infrmatin needed t run the in-mtin weighing system. CYCLE ARMS Infrequently if the cart lifter arm is nt in the READY TO WEIGH psitin at pwer n, this message infrms the peratr t re-psitin the cart lifter arm back t the READY TO WEIGH psitin s weighing can begin. READY TO WEIGH Infrms peratr that the cart lifter weigh-inmtin system is ready t weigh. WEIGHING LOAD This message is displayed nce the cart lifter arm has reached the start f the weighing windw. There is n need t stp the arm during the weighing sequence as LadMan cmputes the weight while the arm is in-mtin. GROSS xxxxxx Grss weight f the laded cart nce the arm has been raised abve the weighing windw. xxxxxx represents the grss weight f the cart and its cntents. 24

25 Nrmal Operating Mde DUMP xxxxxx LOAD xxxxxx These tw messages display alternately t infrm the peratr t cmplete the lifting prcess by cmpletely dumping the lad. xxxxxx represents the grss weight f the cntainer and cntents. If the arms are lwered befre reaching the prgrammed DUMP set pint, LadMan ignres the weight and display the message, IGNORING LOAD!. LOWER ARMS LadMan displays this message nce the lad has been dumped and the arm is being lwered. WEIGHING TARE Message displayed as the emptied cart is being weighed while the arm cntinues lwering belw the weighing windw. NET xxxxxx Displays the net weight where xxxxxx represents the weight f the material just dumped int the truck. RECORDING LOAD The message indicates that the weigh-in-mtin prcess has successfully cmpleted and the net weight has been entered int the lad recrd. Additinally, the recrded net weight is added t the accumulated ttal weight f the TRUCK. 25

26 Nrmal Operating Mde WEIGHT DISPLAYS While in the Nrmal Operating Mde, LadMan presents varius weight displays, sme f which can be cnfigured in the INSTALL/SET DISPLAYS grup f the Setup & Calibratin cmmands (see the sectin n Setup & Cnfiguratin Mde fr instructins n chsing ptinal weight displays). LAST xxxxxx LB Displays the net weight f the cntents dumped frm the last cart picked up and weighed. TRUCK xxxxxx LB Displays the ttal net weight f the cntents dumped int the truck fr all cntainers since the last ZERO TRUCK cmmand was executed. (See PROGRAM FUNCTION belw fr executing the ZERO TRUCK cmmand). TARGET xxxxxx LB This is a prgrammable display that shws the current target net weight set pint. When turned n, this display allws the peratr t set a target net truck weight that will activate an alarm when exceeded. (T enable the TARGET display, use the INSTALL/SET DISPLAYS/TARGET SETPT->ON cmmand in Setup & Calibratin). T prgram the TARGET weight: In the Nrmal Operating Mde lcate the TARGET display using the SELECT key. Nw use the / PROGRAM keys t prgram the target lad weight. Press SET PROGRAM t set and activate the target weight. Sftware Alarm T enable an verlad display message when the TARGET net truck weight is exceeded, use the INSTALL/SET DISPLAYS/FLASH OVERLD cmmand in the Setup & Calibratin mde. S in the nrmal perating mde, the message GROSS >>> TARGET displays any time a net truck weight exceeds the target weight ( NET >>> TARGET when in the NET display mde). 26

27 Nrmal Operating Mde Hardware Alarm T activate a hardware alarm (like a light r buzzer), an verlad hardware signal will shrt t grund whenever the net truck weight exceeds the TARGET set pint value. See Figure 8. LM310 Wiring Diagram fr Cart Based Weight System. Rute Infrmatin Displays While in the Nrmal Operating Mde, LadMan presents varius ptinal displays that can be cnfigured in the INSTALL/SET DISPLAYS grup f the Setup & Calibratin cmmands (see the sectin n Setup & Cnfiguratin Mde fr instructins n chsing ptinal status displays). LOAD NAME & ACCOUNT # Cnfiguring these tw ptinal displays allws the peratr t display, select and recrd a Lad Name and its assciated Accunt Number fr every lad in a pickup rute. This display functin can be turned n r ff by using the INSTALL/SET DISPLAYS/FLASH LDNAME, FLASH ACCT# and FLASH STOP# cmmands in the Setup & Calibratin Mde. When these ptins are turned n, the Lad Name, Accunt Number and/r Stp Numbers will flash n the LadMan display. This helps the driver identify the pickup accunt. When enabled, up t 940 sixteen unique alphanumeric character lad names alng with their assciated seven digit accunt numbers can be dwnladed frm LadMan s Lad Manager Sftware. The Stp Number is the sequence number the pickups were laded int LadMan frm Lad Manager Sftware. Lad Manager Sftware uses varius cmmunicatin methds (such as wireless Bluetth r cellular mdem) t cnnect and dwnlad rute and accunt infrmatin. When the Lad Manager sftware dwnlads rute infrmatin t the LadMan meter, the number f Lad Names, Accunt Numbers and Stp Numbers are set autmatically. The lad name, accunt number and stp number cmbinatin is tied t each lad t be picked up n the peratr s rute. When a lad is recrded cnfirmed by the RECORDING LOAD infrmatin display message the currently displayed lad name, accunt number and stp number are recrded int LadMan s data cllectin memry. After all f the lad and rute infrmatin is recrded, LadMan autmatically sequences t the next lad name/accunt number in the rute list (if enabled with the SET 27

28 Nrmal Operating Mde RECORD Optin f the Setup and Calibratin Mde). Unexpected departures frm the planned sequence in the rute list can be managed using the PROGRAM grup f keys t select an ut f sequence stp and lad r by using accunt barcdes frm a Rute Sheet. Use Ge Ruting Mde t nly display thse accunts within defined radius (300 t 1000 feet) f the Trucks lcatin. Refer t the sectin Cllecting Lad Data fr details. STOP # xxx In additin t the ptinal Lad Name and Accunt Number, every lad has a Stp Number (#) that is recrded in LadMan s data cllectin memry whenever a lad is recrded. The Stp Number represents the sequence in the rute list f Lad Names and Accunt Numbers that have been dwnladed by the LadMan Lad Management Sftware. The Stp Number is prgrammable and allws the peratr t select accunts by prgramming any stp number that has been previusly laded int its memry frm Lad Manager Sftware. Each time a lad is recrded, LadMan autmatically increments the stp number (if enabled with the INSTALL/SET RECORD/INCR STOP# cmmand). This ptinal display functin can be setup t flash during a weight display using the INSTALL/SET DISPLAYS/FLASH STOP# cmmand in the Setup & Calibratin Mde. The stp number is reset t ne (1) whenever LadMan s Lad Manager Sftware dwnlads rute infrmatin. The peratr can verride the current stp number by using the PROGRAM grup f keys t prgram a desired stp number. Refer t the sectin Cllecting Lad Data fr the ut f sequence instructins. PRODUCT NAME LadMan allws up t 50 different Prduct Names t be captured whenever a lad is recrded int the data cllectin memry. (These prduct names can be dwnladed with LadMan s Lad Manager Sftware.) This ptinal display functin can be setup t flash a PRODUCT NAME during a weight display by using the INSTALL/SET DISPLAYS/FLASH PRODUCT cmmand in the Setup & Calibratin Mde. When the Lad Manager Sftware dwnlads rute infrmatin t the LadMan meter, the 28

29 Nrmal Operating Mde number f Prduct Names is set autmatically. When enabled, and befre a lad is recrded, the peratr can select a prduct name (e.g., RECYCLE, CARBOARD, COMPOST, etc.) that will be recrded in LadMan s data cllectin memry. T chse a prduct name: Lcate the current PRODUCT display using the / SELECT keys. Lcate the particular prduct name using the / PROGRAM keys. Activate the prduct name with the SET PROGRAM key. When a lad is recrded cnfirmed by the RECORDING LOAD infrmatin display the prduct name is recrded int LadMan s data cllectin memry alng with the accunt name, accunt number, stp number and any ther enabled rute ptins. Once a prduct name has been selected, it remains in effect fr all subsequent lad recrdings. The prduct name shuld be reprgrammed whenever the prduct cnditin changes. EVENT LadMan prvides up t 50 different Event Cnditins that can be recrded whenever a lad is recrded int the data cllectin memry. (These event cnditins can be dwnladed with LadMan s Lad Manager Sftware.) This ptinal display functin can be setup t flash an EVENT cnditin during a weight display by enabling the functin with the INSTALL/SET DISPLAYS/FLASH EVENT cmmand in the Setup & Calibratin Mde. When the Lad Manager sftware dwnlads rute infrmatin t the LadMan meter, the number f event cnditins is set autmatically. When enabled, and befre a lad is recrded, the peratr can select an event cnditin (e.g., ROAD CLOSED, CONTAINER LOCKED, etc.) that will be recrded in LadMan s data cllectin memry. T chse an event cnditin: Lcate the current EVENT display using the / SELECT keys. Then lcate the particular event cnditin using the / PROGRAM keys. Activate the event/prblem cnditin with the SET PROGRAM key. When a lad is recrded cnfirmed by the LOGGING EVENT infrmatin display the Event cnditin is recrded int LadMan s data cllectin memry alng with the accunt name, accunt number and any ther 29

30 Nrmal Operating Mde enabled rute ptins. Once an event cnditin has been selected and recrded, it reverts back t the NO EVENT cnditin fr all subsequent lad recrdings. New event cnditins shuld be re-prgrammed anytime an event r prblem is encuntered, and befre a lad is recrded. DATE and TIME The currently displayed Date and Time is recrded in LadMan s data cllectin memry whenever a lad is recrded int the data cllectin memry. This display functin is nt ptinal. Prgramming DATE and TIME Using the prgramming basics discussed in the previus sectin, the date and time can be changed with the PROGRAM keys: Lcate the Date and Time display with the SELECT key. Nw use the / PROGRAM keys t prgram the time (hurs, minutes, AM/PM) and date (mnth, day, year). Press SET PROGRAM t set and activate the new time. 30

31 Nrmal Operating Mde PROGRAM FUNCTION Displays Use the PROGRAM FUNCTION display t access and activate any f the cmmand ptins listed belw in Table 5. SHOW NET SHOW GROSS PRINT LAST LOAD ZERO CART LOAD CYCLE DISPLAY ZERO TRUCK Table 5. PROGRAM FUNCTION Cmmands Set display fr NET weight peratin. Set display fr GROSS weight peratin. Prints the mst recent lad data measured t a cnfigured printer. Resets the Cart Lifter lad cells t read zer Initiates the autmatic display cycle f weight infrmatin and status messages Zers the accumulated truck lad TOTAL and prvides ptin t capture a landfill dump weight Use the / SELECT keys t lcate the PROGRAM FUNCTION display. Use the / PROGRAM keys t sequence thrugh available prgram ptins. = frward = reverse Use the SET PROGRAM key t activate cmmand. Either f the / PROGRAM keys will sequence thrugh the available PROGRAM FUNCTIONs, and nce an item is selected, the SET PROGRAM key will activate and save the selectin. LadMan will then return t the Infrmatin Display. While in the PROGRAM FUNCTION displays, LadMan will take n actin until the SET PROGRAM key is depressed. While within any f the PROGRAM FUNCTION ptins, the / SELECT keys will abrt prgramming and return LadMan t manual display. SHOW GROSS Set the display fr GROSS weight mde, enabling LadMan t display the grss TRUCK weight which is the paylad weight plus the tare weight prgrammed in the SET TARE mde f the Setup and Calibratin 31

32 Nrmal Operating Mde mde. While in the GROSS display mde, the truck s weight (TRUCK xxxxxx glb) will be displayed in grss weight. Chsing the GROSS weight display will terminate the NET display peratin. SHOW NET Set the display fr NET weight mde, enabling LadMan t display the net TRUCK weight (r the paylad weight). While in the NET display mde the truck s weight (TRUCK xxxxxx nlb) will be displayed as net weight. Chsing the NET weight mde display will terminate the GROSS mde display peratin. PRINT LAST LOAD Prints the mst recent lad measurement t an utput device cnnected t an RS232 Prt; such as a printer. Lad data includes the current lad data, date and time, GPS crdinates, and any ther ptinal rute display infrmatin that has been enabled with the INSTALL/SETUP RS232/PRINT cmmands (i.e., Accunt Name, Accunt Number, Stp Number, Prduct Name, Event, etc.). Figure 6. Print Ticket Example shws a sample printut frm an in-cab printer (the diamnds ( ) represent ptinal fields that may be setup with the INSTALL/RS232/PRINT cmmands in Setup & Cnfiguratin Mde). DATE: TIME: 12:34:56 PM ** LOAD NAME *** ACCOUNT # STOP # 194 * PRODUCT NAME * TARGET 9600 LB LOAD 560 LB TOTAL LB Figure 6. Print Ticket Example If yu wuld like t take advantage f custm print capabilities, cntact LadMan directly t btain related technical specificatins and dcumentatin r get a develpment qute. ZERO CART LOAD Zers the cart lifter ladcells s it will read zer. This cmmand is useful when there is nthing laded n the cart lift. This cmmand shuld be used when LadMan weighs smething ther than zer when n cart is n the cart lifter when ging up and dwn. If this is the case, 32

33 Nrmal Operating Mde executing this cmmand will direct LadMan t lead the peratr thrugh a prcess t zer the Cart Lifter weight reading. REMOVE CART Make certain there is n lad n the cart lifter. SET ARM ANGLE - LadMan nw displays the ARM Angle. Raise r lwer the arms f the cart lifter t where the cart lifter munting plate is vertical. When the angle is ±1 degree f zer, LadMan will zer the Ladcell readings in this static psitin, and display ZERO COMPLETE t cnfirm the zer cart lad and zer cart angle. Calibrate System fr ZERO CART LIFTER LOAD Switch LadMan als features a ZERO CART LOAD switch that is munted n the left utside plate f the cart lifter scales. This light/switch allws the peratr t wrk at the rear f the truck, reading the green strbe light while leveling the cart arm angle t zer. Depressing this switch initiates the zer lad prcess that was just described abve. And it als features a green light strbe that prvides real-time feedback n the cart angle. The clser the angle t zer, the faster the light flashes. And when the frk angle is between 0 and +/-1, the light will hld steady. When finished zering the lad, the light prvides a high frequency chattering strbe indicated that the Zer Weight is calibrated accurately. When finished, depress the switch t turn ff the light and the zering prcess. CYCLE DISPLAY Directs LadMan t autmatically cycle thrugh all f the available displays (rder listed in Table 4. Nrmal Operating Mde Display). The duratin f each item displayed is cnfigurable using the INSTALL/SET DISPLAYS/CYCLE cmmand in the Setup & Calibratin Mde (default is 2 secnds). 33

34 Nrmal Operating Mde Pressing either the / SELECT keys will terminate the autmatic cycle display and allws manual selectin f the display by using either f the / SELECT keys. ZERO TRUCK Zers the accumulated TRUCK lad ttal. Thereafter, TRUCK xxxxxx nlb will display the accumulated net weight f any recrded lads. Or, TRUCK xxxxxx glb will display the truck s accumulated grss weight - ttal f the truck s tare weight and the accumulated weight f any recrded lads. It is recmmended that the driver zer the truck after any transfer statin r landfill dump - resetting the accumulatr t zer - befre cntinuing the rute r starting a new rute. ENTER GROSS SCALE WEIGHT! The ZERO TRUCK cmmand als features the ptin t capture the grss platfrm scale weight f the laded truck just befre a landfill dump. This weight will be recrded and reprted t LadMan Lad Manager t assist in tracking all the truck s tipping weights at landfills and transfer statins. Nte that the landfill scale lcatin must be gecded in rder fr Lad Manager t recrd the scale weight in the crrect landfill custmer recrd. SCALE LBg Use the / PROGRAM keys t the platfrm scale weight (the grss weight f the truck). Press SET PROGRAM t set and activate. ENTER TARE SCALE WEIGHT SCALE LBt Use the / PROGRAM keys t enter the truck s tare scale weight. Press SET PROGRAM t set and activate. 34

35 Nrmal Operating Mde LadMan respnds with the cnfirmatin that the truck s net lad weight has been recrded at the scale lcatin, fllwed by cnfirmatin that the net truck weight has been set t zer. RECORDING LOAD! ZEROING TOTAL! If n SCALE value is entered then LadMan will respnd with the message: NO LANDFILL SCALE Fllwed by the cnfirmatin: ZEROING TOTAL meaning that the truck s net weight has been set t zer. 35

36 Setup and Calibratin Mde 36

37 Setup and Calibratin Mde SETUP & CALIBRATION MODE LadMan s Setup & Calibratin Mde prvides the peratr the capability t prgram advanced functinality, setup and calibrate a truck s cnfiguratin, chse ptinal infrmatin displays, enable cmmunicatins, and trublesht issues. Refer t Table 6. SET ZERO SET SPAN SET TARE INSTALL SET DEFAULTS Table 6. Setup & Calibratin Cmmands Used fr setup and calibratin f the Cart Lifter Arm Angle Sensr and the Cart Lifters lad sensrs Calibrates LadMan t readings taken frm anther scale Sets the empty weight f the vehicle Prvides the capability t setup and/r change the perating cnfiguratin f LadMan Returns all settings t the riginal factry default settings SELECT Sequence frward thrugh available displays / PROGRAM Keys t change NO t YES SET PROGRAM T activate cmmand ERASE DATA TROUBLESHOOT Permanently erases all data in LadMan s data cllectin memry Prvides detailed sensr, ladcell, cmmunicatins and ther system infrmatin that can be useful fr islating issues SELECT Sequence in reverse thrugh available displays 37

38 Setup and Calibratin Mde Basic Navigatin Activating Setup & Calibratin Mde w/security OFF Cntinually depress the POWER buttn, thrugh the GOODBYE! message, and until the LOADMAN SETUP message is displayed. The first setup & calibratin categry displayed is SET ZERO?---->NO. Activating Setup & Calibratin Mde w/security ON Cntinually depress the POWER buttn. The messages GOODBYE! and ENTER PASS CODE! will display. At the prmpt, PASS CODE 0, use the / PROGRAM keys t prgram the security cde TO 123 and save the cde with the SET PROGRAM key. If crrect, LadMan displays the message, LOADMAN SETUP. The first setup & calibratin categry displayed is SET ZERO?---->NO. If the security cde is NOT crrect, the errr message, SECURITY FAILED is displayed, and the Setup & Calibratin mde cannt be accessed. Navigating and Prgramming Setup & Calibratin Mde The SELECT keys are used t manually scrll thrugh the seven setup, calibratin and trubleshting categries. The SELECT key will sequence frward thrugh a grup f displays. The SELECT key will sequence in reverse thrugh a grup f displays. Once the desired setup categry is displayed, use either f the / PROGRAM keys t tggle NO, YES r ther ptins; and then press the SET PROGRAM t select and activate the setup categry. Fr prgrammable displays (like setting a tare weight): Use the PROGRAM key t mve the flashing cursr left t the next prgrammable digit/item in the display. Once the flashing cursr is psitined ver the item t be changed, use the PROGRAM key t increase/bump the digit/item t its next value. Cntinue t use the / PROGRAM keys until the display has been prgrammed. The SET PROGRAM key will execute the cmmand and save any changes made t the display. LadMan will abrt the prcess f prgramming displays if either f the / SELECT keys are pressed. 38

39 Setup and Calibratin Mde Exiting Setup & Calibratin Mde When finished with any f the setup categries and t exit setup & calibratin: Press the SELECT key until EXIT SETUP?-->NO is displayed. Then press PROGRAM key t display EXIT SETUP?-->YES. Finally, press the SET PROGRAM key t exit. LadMan will nw return t the nrmal perating mde and will reinitiate the infrmatin displays f weight and status messages. Setup & Calibratin Cmmands SET ZERO Zers the cart lifter ladcell weight reading. This cmmand is useful when nthing is laded n the cart lifter but LadMan still weighs smething ther than zer when the cart lifter is ging up and dwn. If this is the case, executing this cmmand will direct LadMan t lead the peratr thrugh a prcess t zer the cart lifter s weight reading. ZERO ARM ANGLE Use the PROGRAM key t select ZERO ARM ANGLE? and activate with the SET PROGRAM key. THIS IMPACTS YOUR CALIBRATION and then the PROCEED? NO cmes up. Use the Prgram Grup f keys t change the NO t YES and then press the SET Key. POSITION ARMS TO ZERO ARM ANG and then READY?-->NO cmes up n the display. Mve the cart lifter munting plates s they are perfectly vertical (recmmend using a Level fr this step). When ready, use the Prgram keys t change the NO t a YES and press the Set Key. ZEROING ARM ANGLE, then ZEROING COMPLETE. The arm angle sensr munted n the cart lifter arms is nw calibrated t read zer in the cart lifter s current psitin. ZERO CART LOAD LadMan respnds with REMOVE CART! and then SET ARM ANG =0 and then starts displaying the cart lifter arm angle. Raise r lwer the cart lifter arms until the angle reading is within ±1 degree f zer. At that pint, LadMan will autmatically calibrate the ladcell readings t read zer. 39

40 Setup and Calibratin Mde LEARN ZERO? Learn Zer is the prcess f custm learning the zer respnse f the cart tipper s ladcells; fine tuning the accuracy f each ladcell. This is accmplished by a series f lifts (12-15 lifts are recmmended). Withut this prcedure the ladcell measurements culd be inaccurate and misleading. The prcess is quite simple. Just fllw the LadMan display instructins: Activate with the SET PROGRAM key. REMOVE CART! Remve the cart fr the entire LEARNING prcess. RAISE ARMS! LEARNING ZERO UP LOWER ARMS! LEARNING ZERO DN CYCLES Displays the number f LEARN cycles cmpleted. The abve prcess shuld be repeated frm times t allw LadMan t fully determine each ladcell s zer respnse; fine tuning the accuracy f each ladcell. When finished repeating this prcess, simply let the cart lifter rest at zer. LadMan will prvide screen instructins t cmplete the LEARN prcess: UPSELECT IF DONE - SELECT. SAVE ZERO? Use the PROGRAM prgramming key t chse YES, and cnfirm with the SET PROGRAM key. SAVING ZERO DATA Wait fr LadMan t prcess befre activating any further keys. SET SPAN Used t calibrate LadMan t the readings taken frm anther scale. Use this setup cmmand t calibrate a truck lad f material that has been weighed n anther scale; r alternately, calibrate LadMan t the weight f a laded cart weighed n anther calibrated scale. Prir t perfrming SET SPAN setup n a truck lad f material, LadMan must display a ZERO TRUCK net weight when the vehicle is empty. If nt, then perfrm a PROGRAM FUNCTION/ZERO TRUCK cmmand when the vehicle is empty. Otherwise an inaccurate 40

41 Setup and Calibratin Mde calibratin will result. Prir t perfrming the SET SPAN setup cmmand with a calibrated cntainer, an empty cart lad shuld measure a net weight f zer. If nt, then perfrm a PROGRAM FUNCTION/ZERO CART LOAD cmmand. Otherwise an inaccurate calibratin will result. SET SPAN Calibratin Prcedure -- This prcedure is used fr either calibrating a laded cart r fr calibrating a single cntainer that is laded with a calibrated weight that is near % f the cart lifter s lad capacity. Use the PROGRAM key t select SPAN TRUCK? and activate with the SET PROGRAM key. LadMan asks fr cnfirmatin with ADJUST SPAN? Press SET Prgram key t cnfirm. LadMan respnds with instructins t ENTER METER LOAD. METER xxxxxx LB Use the / PROGRAM prgramming keys t enter the weight readings btained frm the LadMan meter. This wuld be the net (TRUCKn) r grss (TRUCKg) weight fr the truck, r the net lad weight (LAST) fr a cntainer. Press the SET PROGRAM key t save. Press the SELECT key and LadMan will respnd with the directins, ENTER CAL LOAD. Use the / PROGRAM prgramming keys t enter the weight readings btained frm the calibrated scale. Press the SET PROGRAM key t save. Nw press the SELECT key and LadMan will respnd with the directins, DO AUTOCAL?-->NO. This display is cnfirming that the weights have been entered prperly. If a mistake was made when entering the truck s net (r grss) weight (TRUCKn r TRUCKg) r the calibrated lad weight (LAST), simply use the SELECT key t back up and re-enter. Once cnfirmed that the entries are crrect, select YES and press SET. LadMan will nw cmplete the SPAN calibratin and cnfirm with, DOING SPAN ADJUST and SPAN COMPLETE!. 41

42 Setup and Calibratin Mde LEARN SPAN? Learn Span is the prcess f custm learning the calibratin f the cart tipper s ladcells. This is accmplished by a series f lifts (12-15 lifts are recmmended). Withut this prcedure the ladcell measurements culd be inaccurate and misleading. The prcess is quite simple. Just fllw the LadMan display instructins: Activate LEARN SPAN with the SET PROGRAM key. ENTER SPAN CAL (Factry default is 400LB). Press SELECT key t cntinue. ENTER CAL LOAD This is the calibrated weight f a cart laded with a knwn scale weight frm anther calibrated scale. This lad shuld be tightly secured within the cart fr safety, and t make certain there is n abrupt buncing f the cntainer s cntents during the calibratin prcedure. Use the / PROGRAM prgramming keys t enter the weight reading btained frm the calibrated scale. Press the SET PROGRAM key t save, and press SELECT key t cntinue. LadMan will respnd with LOAD CAL WEIGHT! and has initiated the LEARN SPAN calibratin prcess: RAISE ARMS! LEARNING SPAN UP LOWER ARMS! LEARNING SPAN DN CYCLES Displays the number f LEARN cycles cmpleted. The abve prcess shuld be repeated frm times t allw LadMan t fully determine each ladcell s span; fine tuning the calibratin f each ladcell. When finished repeating this prcess 12 t 15 times, simply let the cart lifter rest at zer. LadMan will prvide screen instructins t cmplete the LEARN prcess: UPSELECT IF DONE - SELECT. SAVE SPAN? Use the PROGRAM prgramming key t chse YES, and cnfirm with the SET PROGRAM key. SAVING SPAN DATA Wait fr LadMan t prcess befre 42

43 Setup and Calibratin Mde activating any further keys this may take few mments. SET TARE Sets the empty weight f the vehicle referred t as the tare weight. LadMan uses the cnfigured tare weight t display the grss weight f the vehicle when LadMan is cnfigured fr grss weight peratin (activated by the PROGRAM/SHOW GROSS cmmand). The grss weight is the net weight (r paylad weight) plus the tare weight; and it is the tare weight that is set by using this cmmand. First btain the tare weight by weighing the fully fueled empty truck at a calibrated truck scale, and write dwn the tare weight here: TRUCK TARE WEIGHT: When the SET TARE categry is activated, the message TRUCK xxxxxx LB is displayed where xxxxx is the current tare setting fr the truck. Use the / PROGRAM and SET PROGRAM keys t change and set the truck s tare setting. Nte that the truck tare is assumed t be a cnstant. This f curse will nt be the case in the real wrld. Just the variatin f the fuel remaining in the truck can cause the truck s empty weight t vary 1000 lbs. We recmmend using a full tank f fuel when measure the truck s empty weight s this shuld always represent the highest pssible weight f the truck. 43

44 Setup and Calibratin Mde INSTALL Prvides the capability t setup and change the perating cnfiguratin f LadMan. When activated with YES, then the first installatin ptin is displayed; LOADCELLS 2. Mst cart lifters will have nly 2 Ladcells but sme mdels will have mre. The available INSTALL ptins are shwn in Table 7. These categries are selected and activated using the / SELECT, / PROGRAM and SET PROGRAM keys. Table 7. INSTALL - Installatin Cmmands LOADCELLS SHOW NEG WTS SET DISPLAYS Displays the number f ladcells that are cnfigured fr lad weight sensing. Default is 2. Cnfigures hw LadMan will display negative weights Prgrams LadMan s display ptins SELECT Sequence frward thrugh available displays SETUP MODEM SETUP GPS SET RECORD SETUP RS232 SERIALnum SECURITY Cnfigures the cmmunicatins mdem Prgrams the time perid between lgging f GPS crdinates Cnfigures ptins t custmize hw lad data is recrded and/r displayed Cnfigures LadMan s RS232 prt(s) Displays the serial number fr the LadMan meter Turns LadMan meter security ON r OFF / PROGRAM Prgramming keys SET PROGRAM T activate cmmand SELECT Sequence in reverse thrugh available displays 44

45 Setup and Calibratin Mde LOADCELLS Displays the number f ladcells that are cnfigured fr lad weight sensing. This value is set t a default f 2 ; which accunt fr the tw cart lifter lad cells that measure the weights laded n the cart lifter. Sme cart lifter mdels will have mre than 2. Use the / PROGRAM keys t adjust this value if mre lad cells are used fr the scale. SHOW NEG WTS Cnfigures hw LadMan will display negative weights. Use the / PROGRAM Prgramming keys t advance thrugh the 4 ptins. NO YES LadMan will nt display any measured negative net weights; but instead will display negative weights as zer. Directs LadMan t display all negative weights. <75 LadMan will display a weight f zer fr any negative weights between zer and negative 75 punds. Any value less than negative 75 punds will display as measured. <150 LadMan will display a weight f zer fr any negative weights between zer and negative 150 punds. Any value less than negative 150 punds will display as measured. 45

46 Setup and Calibratin Mde SET DISPLAYS This setup categry prgrams LadMan s display ptins. Refer t Table 8. DISPLAY UNITS CYCLE COUNT BY ACCOUNTS PRODUCTS EVENTS ASSETS TARGET SETPT FLASH LDNAME FLASH ACCT# FLASH STOP# FLASH PRODUCT FLASH EVENT FLASH OVERLD GEO ROUTE Table 8. SET DISPLAY Cmmands Selects the units fr measuring and displaying weights Prgrams the viewing duratin f each displayed weight Prgrams the reslutin f the weight displays The number f rute Accunt names and numbers that have been dwnladed t Ladman The number f rute Prduct names that have been dwnladed t the Ladman meter The number f rute Events that have been dwnladed t the Ladman meter The number f assets that have been dwnladed t the Ladman meter Display TARGET weight s a target verlad set pint can be prgrammed Active Lad Name will be flashed every few secnds n the meter display Active Accunt Number will be flashed every few secnds n the meter display Active Stp # will be flashed every few secnds n the meter display Currently active PRODUCT will be displayed Currently active EVENT will be displayed LadMan will place a message n the display anytime the TARGET weight has been exceeded Ge Rute infrmatin will be dwnladed frm Lad Manager sftware and activated n cmmand 46

47 Setup and Calibratin Mde DISPLAY UNITS Selects the units fr measuring and displaying weights. The LadMan meter cmes precnfigured at the factry t display weight measurements in English units. Use the / PROGRAM and SET PROGRAM keys t prgram, select and set either English r metric units. English units select punds (LB Metric units select kilgrams (KG) CYCLE xxx SEC Prgrams the viewing duratin (xxx secnds) f each weight, rute r status message displayed during the Nrmal Operating Mde autmatic cycle display. Use the / PROGRAM and SET PROGRAM keys t prgram, select and set the display duratin in secnds. The Cycle Display Functin can be cmpletely disabled by setting the xxx value t zer (0) (Default is 2 secnds and maximum is 10 secnds.) COUNT BY = xxx Prgrams the reslutin f the weight displays where xxx is the minimum weight step displayed. The available COUNT BY weight step ptins are, 1, 2, 5, 10, 20, 50, 100 r 200. The COUNT BY runding can be mmentarily disabled n the display by cntinually depressing the SELECT key that is used t manually select a particular weight display. LadMan will display the weight cunt in increments f 1 as lng as the SELECT key is cntinuusly depressed. Releasing the SELECT key causes the display t return t the prgrammed COUNT BY reslutin. ACCOUNTS Lad Manager Sftware will autmatically lad the number f rute accunt names and numbers that have been dwnladed int LadMan s memry. This number is autmatically set when LadMan Lad Manager Sftware dwnlads ACCOUNTS but can be verridden with this cmmand (prgramming t zer will remve all accunts). 47

48 Setup and Calibratin Mde Regarding Accunt Lad Names, Accunt Numbers, Prducts and Events: LadMan allws up t 940 different Lad Names & crrespnding Accunt Numbers, 50 unique Prduct Names, 50 Events and 250 different Assets t be captured upn each recrding f a lad - RECORDING LOAD. These accunt names, prducts, events, and assets can be dwnladed t the meter with LadMan s Lad Manager Sftware. PRODUCTS Cnfigures the number f rute prduct names that can be displayed (default is 0, max is 50). This number is autmatically set when LadMan Lad Manager dwnlads PRODUCTS but can be verridden manually. EVENTS Cnfigures the number f rute events that can be displayed (default is 0, max is 50). This number is autmatically set when LadMan Lad Manager dwnlads EVENTS but can be verridden manually. Example EVENTS are ROAD CLOSED, GATE LOCKED, NO BIN AVAILABLE, etc. ASSETS Cnfigures the number f rute assets that can be displayed (default is 0, max is 250). This number is autmatically set when LadMan Lad Manager dwnlads ASSETS, but can be verridden manually. TARGET SETPT Turns n r ff the TARGET weight display. When turned n, this display allws the peratr t set a target verlad set pint that will activate a hardware alarm and/r will trigger a LadMan display when the target net weight f the truck has been exceeded. Especially useful fr tracking and detecting the current grss weight f the truck; aviding verlads and fines. FLASH LDNAME When this display is activated t YES, the currently active Lad Name will be flashed every few secnds n the weight display, aiding the peratr t identify the current accunt that will be saved when a lad is recrded as an aid t easily identify the active accunt. 48

49 Setup and Calibratin Mde FLASH ACCT# When this display is activated t YES, the currently active ACCOUNT# will be flashed every few secnds n the weight display, aiding the peratr t identify the current accunt that will be saved when a lad is recrded. FLASH STOP# When this display is activated t YES, the currently active STOP# will be flashed every few secnds n the weight display, allwing the peratr t identify the current accunt stp number that will be saved when a lad is recrded FLASH PRODUCT When this display is activated t YES, the currently active PRODUCT (refuse, recycling, cardbard, etc.) will be displayed. When enabled, and t chse a prduct name: Lcate the PRODUCT display using the / SELECT keys, Lcate the particular prduct name using the / PROGRAM keys, Activate the prduct name with the SET PROGRAM key. When the lad is recrded, the prduct name will be recrded int LadMan s data cllectin memry alng with the accunt name, accunt number, and any ther enabled rute ptins. Once a prduct name has been selected, it will remain in effect fr all subsequent lad recrdings. The prduct name shuld be re-prgrammed whenever the prduct cnditin changes. FLASH EVENT When this display is activated t YES, the currently active EVENT will be displayed. When enabled, and t chse a prblem cnditin: Lcate the current EVENT cnditin display using the / SELECT keys, Lcate the particular prblem cnditin using the / PROGRAM keys, Activate the prblem cnditin with the SET PROGRAM key. When a lad is recrded, the event cnditin will be recrded int LadMan s data cllectin memry alng with the accunt name, 49

50 Setup and Calibratin Mde accunt number and any ther enabled rute ptins. Once an EVENT cnditin has been selected and recrded with the RECORD cmmand, it will revert back t the NO EVENT cnditin fr all subsequent lad recrdings. New event cnditins shuld be re-prgrammed anytime a rute event/prblem is encuntered and befre the next lad is recrded. FLASH OVERLD When activated t YES, LadMan will place a message n the display (and activate an ptinal hardware alarm) anytime the TARGET weight has been exceeded. In the nrmal perating mde the message, GROSS >>> TARGET will display anytime a lad exceeds the target weight. Especially useful fr tracking and detecting the current grss weight f the truck; aviding verlads and fines. GEO ROUTE Rute infrmatin will be dwnladed frm LadMan Lad Manager Sftware when set t YES. The GEO ROUTE feature can then be selected as the active Operating Mde using PROGRAM FUNCTION display in the nrmal perating mde. Ge Rute, als knwn a prximity ruting, allws LadMan t determine whether rute pickups are lcated within a prximity f 300 t 1000 feet (prgrammable). If nly ne custmer name is indicated n the 16 character display, then the driver can simply lift the lad as instructed n the display. If mre than ne custmer accunt is displayed, then LadMan has detected ther custmers with the prximity f the truck. The driver must chse the crrect custmer in rder t reprt the crrect weight with the crrect custmer accunt. Lcate and chse the custmer accunt using the / PROGRAM keys. Activate the accunt with the SET PROGRAM key SETUP MODEM When set t YES, the cmmand cnfigures the cmmunicatins mdem. The LadMan meter may cme equipped with an ptinal GSM cellular 50

51 Setup and Calibratin Mde mdem. The mdem is used t cnnect and cmmunicate with LadMan s Lad Manager Sftware. The Lad Manager Sftware allws remte tracking f trucks, drivers, custmers and rutes, and exchanges the lad and lcatin infrmatin thrugh this mdem. MODEM OPTION Set this ptin t YES if the LadMan meter has been cnfigured with a GSM mdem bard fr remte cmmunicatins. If the mdem is nt installed, make certain t chse the NO ptin. MODEM ---- cuntry Sets the cuntry in which the cell mdem will perate. The default cnfiguratin is USA. Chse USA r CANADA using the PROGRAM key, Activate the cuntry with the SET PROGRAM key. Internatinal Mdems - If the cuntry is utside the USA and Canada, then the cuntry shuld be left n USA. The meter has t be rdered with an Internatinal Optin fr this t wrk prperly. CONN xxx SEC Sets the time perid (in secnds) between plling cnnectin attempts between the LadMan meter and the LadMan Lad Manager Sftware. RSET xxxx SEC Sets the time perid (in secnds) when the mdem will reset if it has nt been fully exercised within the xxx time windw. The factry default is 3600 secnds (1 hur). If the RSET is executed, then the mdem had prbably been stuck in sme state. RSET will tggle pwer t the mdem and reset. This value can be adjusted with the / PROGRAM and SET PROGRAM keys. BAUD RATE> Indicates the baud rate f the mdem. This number shuld always be set t If nt, use / PROGRAM and SET PROGRAM keys t crrect the value. 51

52 Setup and Calibratin Mde Remte IP The remte IP address fields cntain the IP address f the LadMan TCP relay that crdinates data cmmunicatin between the vehicle and the LadMan Lad Management Sftware. When using a cellular data mdem, these IP addresses must be set as dcumented: RemteIP1 74 RemteIP2 93 RemteIP3 98 RemteIP4 177 If fr any reasn these LM310 values d match the values listed here, then use the / PROGRAM and SET PROGRAM keys t prgram, select and crrect t the address fields as shwn.. SETUP GPS When set t YES, this cmmand prgrams the lgging f GPS crdinates. The LadMan meter may cme equipped with an ptinal internal GPS chip and antennae. LadMan s Lad Manager Sftware uses nbard GPS capability t track and map truck, lad and custmer lcatins. LOG xxx SEC Prgrams the time perid (xxx secnds) between the lgging f GPS crdinates int LadMan s data cllectin memry. The factry default setting is 30 secnds. When recrded GPS crdinates are upladed int LadMan s Lad Manager Sftware, the sftware will be able t use the crdinates t map lad lcatins, track truck rutes and aid with several ther advanced lcatin based functins. SET RECORD Whenever a lad is recrded using the RECORD LOAD cmmand, LadMan uses several recrd ptins t custmize the way that the lad data is displayed and recrded. Chse YES t prgram the fllwing RECORD ptins: RECORD&PRINT When set t ON, directs LadMan t print the recrded lad data t the RS232 prt(s) as it is recrded int LadMan s data cllectin memry. If set t OFF, the lad data 52

53 Setup and Calibratin Mde will be recrded t LadMan s data cllectin memry, but will nt be printed. TIME: 12:34:56 PM ** LOAD NAME *** ACCOUNT # STOP # 194 * PRODUCT NAME * TARGET 9600 LB LOAD 560 LB TOTAL LB Figure 7. Printed Lad Ticket INCR STOP # -- When set t ON, LadMan will autmatically increment and select the next stp number (and assciated accunt infrmatin) frm the dwnladed rute list after a lad has been recrded. If n Rute has been dwnladed then the STOP # will simply increment n every lad pickup. CONTsp xxxxx LB Cntainer set pint. LadMan prvides this capability t prevent the recrding f lad data recrds when there is n cart n the cart lifter. When prgrammed t a psitive number, and if the grss weight measured ging up is less than this set pint value, then the weight will NOT be recrded as a lad data recrd when the lad cmes back dwn. If prgrammed t zer then every lift will be recrded regardless f the grss cart weight measured ging up. SETUP RS232 Cnfigures LadMan s RS232 prts. LadMan cmes standard with ne 9-pin RS232 prt that can cnnect t peripherals like printers fr printing lad and rute infrmatin, r t large screbard displays munted n the truck t display weight infrmatin. Als, the RS232 prt can cnnect t input devices like barcde readers fr reading accunt and rute infrmatin. Optinally, the LadMan meter cmes with a secnd RS232 prt cnfigured with either anther 9-pin cnnectr r with a Bluetth antenna. Here are the three pssible RS232 prt cnfiguratins: 53

54 Setup and Calibratin Mde Table 9. RS232 Prt Cnfiguratins RS232 Cnfiguratin Prt #1 Cnnectr Prt #2 Cnnectr Standard 9-pin - Optin 1 9-pin 9-pin Optin 2 Bluetth Antenna 9-pin Fr a Standard ne prt cnfiguratin: Chse RS232 PORT #1? by pressing the SET PROGRAM key. BLUETOOTH ---> shuld be set t OFF as Bluetth is nt available with the standard cnfiguratin. Then cnfigure the remaining prt settings as described belw beginning with BAUD RATE. Nte: Fr the standard 1 prt cnfiguratin, if RS232 PORT #2 is chsen, any f the fllwing RS232 cnfiguratin settings will be ignred as the prt is nt present. Fr Optin 1 tw prt cnfiguratins (tw 9-pin RS232 prts): Fr the first prt, chse RS232 PORT #1? by pressing the SET PROGRAM key. BLUETOOTH ---> shuld be set t OFF as Bluetth is nt available with this cnfiguratin. Then cnfigure the remaining prt #1 settings as described belw beginning with BAUD RATE. Repeat this prcess fr the secnd prt by chsing RS232 PORT #2? and pressing the SET PROGRAM key. Then cnfigure the remaining prt #2 settings as described belw beginning with BAUD RATE. Fr Optin 2, tw prt cnfiguratins (ne Bluetth prt and ne 9- pin prt): Fr the first prt, chse RS232 PORT #1? by pressing the SET PROGRAM key. BLUETOOTH ---> shuld be set t ON. Fr the secnd prt, chse RS232 PORT #2? by pressing the SET PROGRAM key. Then cnfigure the remaining prt #2 settings as described belw beginning with BAUD RATE. 54

55 Setup and Calibratin Mde BAUD RATE Prgrams the baud rate fr the RS232 prts. The baud rate must match the baud rate f the peripheral device that will be cnnected t the prt fr LadMan t prperly cmmunicate. The available baud rates are: 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, baud (factry default is 9600 baud). When the LadMan meter is equipped with the Bluetth Optin, then the baud rate fr prt #1 MUST be set at 9600 baud. The fllwing ptins are available nly fr RS232 9-pin prts: TICKET PRINT ON Prgrams the RS232 prt fr printing t a serial printer munted in the truck cab. Every time a cart is lifted and weighed, it will print the cntents f the lad data measured when the meter is shwing RECORDING LOAD (If the Recrd and Print Optin is set t YES in SET RECORD ptins). Other print ptins can be enabled with the print (PRT) cmmands described belw. SCOREBOARD ON When the SCOREBOARD is set t ON, then the ttal weight will be displayed t the truck s screbard that s cnnected t the RS232 prt. It will always shw the last measured lad and ther print ptins chsen with the SET RECORD/PRT cmmands. BARCODE LadMan supprts autmatic reading f accunt infrmatin with a bar cde reader/wand. When set t ON, LadMan cnfigures the RS232 prt t read frm a barcde reader. The fllwing print ptins may als be ffered fr cnfiguratin, depending n which type f utput device was selected (chse YES t activate any desired ptin). PRT LOADNAME Prints the active lad accunt name. PRT ACCOUNT Prints the active lad accunt number. PRINT STOP# Prints the active stp number. 55

56 Setup and Calibratin Mde PRT PRODUCT Prints the active prduct name. PRT EVENT Prints the active event cnditin. PRINT TRUCKg Prints the truck s grss weight. That is, the tare weight plus the accumulated recrded lad weights. PRINT TRUCKn Prints the truck s net weight. That is, the accumulated recrded lad weights. PRINT CONTg Prints the ttal grss weight f the cntainer and its lad as the arms are raised. PRINT CONT Prints the empty cntainer weight (the cntainer tare weight) as the arms are lwered. PRINT RFID Prints the RFID tag read frm the laded cntainer. PRINT ASSET Prints the ASSET number f the cntainer. PRT TRACE Ignre. Used fr factry service. COUNTBY When ENABLED, the printed lads will reflect step (reslutin) value that was cnfigured in the SET DISPLAY/COUNTBY cmmand. When DISABLED the printed lads will use the actual lad weights measured instead f being runded t the nearest COUNTBY Setting prgrammed fr the LM310 display. LINE FEEDS xx Prgrams the number f line feeds after every PRINT TICKET printut (default is 2; 1 min; 10 max). SERIALnum Displays the serial number f the LadMan meter. The serial number prgrammed int the meter is nly needed when the LadMan Lad Manager data cllectin sftware features are used. Whenever data is upladed t the LadMan Lad Manager Sftware, LadMan will add the serial number t every lad data recrd. This feature is especially useful when maintaining recrds fr a fleet f trucks and is used t identify which truck the meter is in. 56

57 Setup and Calibratin Mde SECURITY When set t ON, LadMan will prmpt fr a valid passcde whenever the LM310 meter is placed int SETUP and CONFIGURATION Mde. When prmpted, enter passcde 123. At this pint, LadMan has cmpleted the INSTALL prtin f the Setup and Calibratin Mde and will cntinue with the remaining Setup & Calibratin ptins (SET DEFAULTS, ERASE DATA and TROUBLESHOOTING). SET DEFAULTS Reset the LM310 t the factry default settings. See Table 10. LM310 Factry Defaults belw fr a listing f the factry default settings. Use the PROGRAM key t chse either DEFAULTS FOR LB? r DEFAULTS FOR KG? and press the SET PROGRAM key t activate. LadMan respnds with the message, THIS RESETS TO FACTORY DEFAULTS. Fllwed by, PROCEED?-----> NO. When selecting YES and activating with the SET PROGRAM key, LadMan respnds with the message, SETTING DEFAULTS. LadMan will abrt the prcess anytime NO is selected r if either f the / SELECT keys is pressed. 57

58 Setup and Calibratin Mde Table 10. LM310 Factry Defaults LOADCELLS 2 RECORD SHOW NEG WTs YES RECORD&PRINT ON DISPLAY INCR STOP # ON DISPLAY UNITS LB / KG CONTsp 30LB / 15KG CYCLE 0 SEC REMOTE SWBOX OFF COUNT BY 20 ACCOUNTS 0 RS232 PRODUCTS 0 BLUETOOTH OFF EVENTS 0 BAUD RATE 9600 ASSETS 0 TICKET PRINT ON TARGET SETPT OFF BARCODE READ ON FLASH LDNAME NO PRT LOADNAME NO FLASH ACCT# NO PRT ACCOUNT NO FLASH STOP# NO PRINT STOP# YES FLASH PRODUCT NO PRT PRODUCT NO FLASH EVENTS NO PRT EVENT NO FLASH OVERLD NO PRINT TRUCKg NO GEO ROUTE NO PRINT TRUCKn YES MODEM PRINT CONTg NO MODEM OPTION NO PRINT CONT NO MODEM USA PRINT LOAD YES CONN 600 SEC COUNTBY DISABLED RemteIP1 74 LINE FEEDS 2 RemteIP2 93 SERIALnum factry setting RemteIP3 98 SECURITY OFF RemteIP4 177 GPS TARE SETTINGS LOG 30 SEC TRUCK 0 LB / KG ERASE DATA Activating this setup categry will permanently erase all data in LadMan s data cllectin memry. When set t YES, LadMan respnds with the message, THIS WILL ERASE ALL LOAD DATA!, Fllwed by, PROCEED?-----> NO. When selecting YES and activating with the SET PROGRAM key, LadMan respnds with the message, ERASING ALL DATA fllwed by LOAD DATA ERASED. LadMan will abrt the prcess anytime NO is selected r if either f the / SELECT keys are pressed. 58

59 Setup and Calibratin Mde TROUBLESHOOT Prvides detailed sensr, ladcell, cmmunicatins and ther system infrmatin that can be useful fr islating issues. In this mde, each sensr s respnse t a lad can be examined in detail, and the infrmatin can be used t manually change calibratin settings. Refer t Table 11. Use the PROGRAM key t advance thrugh the trubleshting ptins, and press the SET PROGRAM key t select an ptin t trublesht. Table 11. TROUBLSHOOT Cmmand Optins TROUBLE LOADCELL TROUBLE COM TROUBLE VOLTAGE TROUBLE GPS TRB LOAD RECORDS TROUBLE POSITION TROUBLE CAL Displays individual Cart Lifter ladcell calibratin settings Prvides LadMan s cmmunicatins settings. Displays individual vltage readings. Prvides current GPS lcatin readings. Displays number f lad recrds in LadMan s data cllectin memry. Displays individual arm and Cart Lifter Arm Angle sensr settings and readings. Prvides zer and span infrmatin fr the Cart Lifter. TROUBLE LOADCELL Select this ptin with the SET PROGRAM key t activate and use the SELECT key t advance thrugh the individual ladcell calibratin settings. CH1 SPAN xxxxxx Current CH1 span setting CH1 xxxxxx LB Current CH2 weight reading CH1 ZERO xxxxxx CH1 zer ffset CH2 SPAN xxxxxx Current CH2 span setting CH2 xxxxxx LB Current CH2 weight reading CH2 ZERO xxxxxx CH2 zer ffset (xxxxxx =Setting r measured setting. TROUBLE COM Prvides detailed infrmatin t aid technicians in 59

60 Setup and Calibratin Mde trubleshting. Select this ptin with the SET PROGRAM key t activate and use the SELECT key t advance thrugh the individual ladcell calibratin settings. CONNECT xxx SEC Displays the number f secnds until the meter will attempt a cellular mdem Internet cnnectin t uplad recrd data t the LadMan Lad Management Sftware. The default is 600 secnds. Any number up t six digits lng can be specified with the SETUP MODEM/CONN cmmands. The number resets autmatically if the cnnectin fails within the specified time. CELLSTATE xxx Used fr diagnsing data cllectin sftware prblems. The number shwn represents the current state f the mdem, which is used by technicians t help diagnse cmmunicatins prblems. State 7 is cmmn, meaning that the mdem is pwered and ready. State 51 signifies that the antenna is missing r there is n receptin. Althugh the CELLSTATE number can be as high as 200, generally any number f 80 and abve means that cmmunicatins are established. See Table 14. Cell State Cdes and Descriptins SIM H: Represents the first 10 SIM card identifying digits. SIM L: Represents the secnd 10 SIM card identifying digits. RESET BTOOTH This resets the Bluetth prt t factry defaults. OSversin x.x.xx This number identifies the perating system used by LadMan. (Sftware updates must be cmpatible with the perating system number.) TROUBLE VOLTAGE Select this ptin t read individual vltage levels. VIN Input vltage. VLC1 Vltage utput t Cart Lifter Pwer VBAT VBAT is the current utput vltage f the nbard rechargeable battery. A fully charged battery is 2.65V t 2.70V 60

61 Setup and Calibratin Mde This ptin als prvides temperature vltage readings fr the LCD display: TEMPsensr xxxx TEMPscaled xxxx CONTRAST By reprgramming CONTRAST t a higher value, the LadMan display cntrast will increase (maximum 1500). Similarly, lwering t a lwer value will decrease the display cntrast. TROUBLE GPS Select this ptin t examine current GPS lcatin readings. LAT deg Displays the current GPS latitude lcatin reading. NO GPS SIG will display if n signal is available. LON deg Displays the current GPS lngitude lcatin reading. NO GPS SIG will display if n signal is available. SATTELITES Displays the number f satellites available fr determining GPS crdinates. LadMan must cnnect with at least three satellites t determine the vehicle s GPS crdinates. ATLTITUDE Displays the current GPS altitude reading in meters. VEL East Displays truck easterly velcity in miles-per-hur (mph). VEL Nrth Displays truck nrtherly velcity in miles-per-hur (mph). NextLOG Displays the number f secnds until LadMan will next recrd the vehicles GPS crdinates. RECORDS Displays the number f GPS recrds currently in flash memry. When the ERASE DATA functin is executed r after the LadMan Lad Manager Sftware cllects all the GPS data, this number will reset t zer. Thereafter, the value is incremented every time a GPS recrd is stred in LadMan s data cllectin memry. TRB LOAD RECORDS Displays the number f lad recrds cntained in LadMan s data cllectin memry (RECORDS xxxxxx). When the ERASE DATA functin is executed r after the LadMan Lad Manager 61

62 Setup and Calibratin Mde Sftware cllects all the lad data, this number is reset t zer. Thereafter, the value is incremented every time a lad data recrd is stred in LadMan s data cllectin memry. (A secnd value, ERASE CTR-xxxxxx, signifying the number f times data has been erased, is prvided fr factry trubleshting.) TROUBLE POSITION Chse this trubleshting ptin t examine individual arm sensr settings and readings. WGH START Displays the starting set pint angle f the weigh-inmtin windw. (Factry setting is 0.0 degrees.) WGH END Displays the ending set pint angle f the weigh-inmtin windw. (Factry setting is 75.0 degrees.) WGH DUMP Displays the dump lad set pint angle f the weighin-mtin windw. (Factry setting is degrees). With mst cart tippers these weighing windw settings shuld wrk crrectly. Hwever, there will be sme carts/bins that may cme in sizes that require different weighing windw settings. Use these three prgramming settings t adjust t cart as necessary. Custm Adjustment f Weigh-In-Mtin Windw The default weigh-in-mtin angle assignments were derived frm the experience LadMan gained wrking with custmers and learning the mst cmmn sized carts used. Hwever, there are carts that might nt fit the weigh windw f 0, 75 and 100. Especially larger carts that are taller than the cart tipper and scale. Fr these larger carts, yu will mst likely need t adjust the weigh windw. Here are sme guidelines: Set the WEIGHT START angle where the cart is ff the grund 6 t 12. This might be frm 5 t 15. The WEIGHT END shuld never be higher than 75. When necessary, the WEIGH END can be set lwer s that the cart des nt start dumping the lad befre the weigh windw has been cmpleted. WEIGH DUMP needs t be at least 10 t 25 abve the WEIGH END set pint. 62

63 Setup and Calibratin Mde The weighing windw angle set pint settings can be prgrammed using the / and SET PROGRAM keys. ARM DIRECTION = +/- This display shuld be used if the arm angle des nt increase in value when the arms are raised. If the arm angle decreases when the arms are raised, then the ARM DIRECTION sign shuld be reversed. ARMS xxx.x DEG Displays the currently measured arm angle in degrees. ARM ZERO The arm s zer degree calibratin cnstant set when the arms are zered. ArmSTRTup First cart arm angle measured after passing WGH START angle prgrammed ging up. ArmENDup Last cart arm angle measured prir t passing the end f weigh-in-mtin windw with the cart ging up. ARMENDdn First cart arm angle measured after passing the end f weigh-in-mtin set pint WGH END with the cart ging dwn. ArmSTRTdn Last cart arm angle measured prir t passing the WGH START set pint weigh-in-mtin windw while the cart is ging dwn. Trace (Service use nly) TraceLst (Service use nly) TROUBLE CAL Prvides zer and span infrmatin t assist with trubleshting and calibratin f the weight sensrs. ZEROUpCAL A zer calibratin adjustment fr weights measured as the cart arm is raised. Nrmally this is zer but if ging up there is a persistent zer errr, then yu can prgram a cnstant zer 63

64 Setup and Calibratin Mde ffset that will be added t every measurement ging up. ZERODnCAL A zer calibratin adjustment fr weights measured as the cart arm is lwered. Nrmally this is zer but if cming dwn there is a persistent zer errr, then yu can prgram a cnstant zer ffset here that will be added t every measurement cming dwn. SPANUpCAL The SPAN calibratin adjustment fr weights measured as the arm is raised. Raising this number 10% will cause the scale t read 10% mre ging up. SPANDnCAL The span calibratin adjustment fr weights measured as the arm is lwered. Raising this number 10% will cause the scale t read 10% mre cming dwn. SampDevUp 500 is recmmended. This is a setting t weed ut spikes in the weigh-in-mtin cycle ging up. SampDevDn 500 is recmmended. This is a setting t weed ut spikes in the weigh-in-mtin cycle cming dwn. The fllwing displays appear in the TROUBLE CAL sequence, but are fr technical reference nly. SampUpRaw SampDnRaw NetRaw SampUpC1 SampDnC1 NetC1 SampUpC2 SampDnC2 NetC2 SampUpC3 SampDnC3 NetC3 LadUpRaw LadDnRaw LadUpC1 LadDnC1 LadUpC2 LadDnC2 LadUpC3 LadDnC3 64

65 Initial Startup and Calibratin Prcedures INITIAL STARTUP AND CALIBRATION The instructins in this sectin prvide a step-by-step prcess fr verifying and calibrating a newly installed LadMan Cart Lifter Weigh-In-Mtin system. Fllw these steps t insure prper installatin and peratin. 1. Verify Wiring 2. Pwer On 3. Verify Arm Angle Sensr 4. Calibrate Arm Angle 5. Verify Arm Angle Measurements respnd crrectly 6. Verify Weigh-In-Mtin Respnse 7. Calibrate System fr ZERO CART Lad 8. Calibrate System Under Lad 9. Fine Tune Span Adjust 1. Verify Wiring Begin by verifying that the electrnics are wired per the wiring diagram shwn in Figure 8 near the end f this manual. Psitive 10VDC t 28VDC shuld cnnect t the LadMan 310 Meter at pins 1 and 2 t pwer the system. Verify cnnectin f the cable harness frm the LadMan meter t the cart lifter weigh-in-mtin assembly. Then verify the cnnectin f the cable harness frm the cart weigh-inmtin assembly t the arm weigh-in-mtin assembly. Finally, verify that the cart lifter ladcells are cnnected t the cart lifter weigh-in-mtin assembly. 2. Pwer On With pwer ff, briefly press the frnt panel POWER buttn. LadMan will pwer n and sign n with the display messages LOADMAN, fllwed by PROG VERSION X.X (where X.X is the sftware versin). LadMan will then cnfirm that the weigh-in-mtin equipment is ready fr peratin with message, READY TO WEIGH!. 65

66 Initial Startup and Calibratin Prcedures When pwer is applied, the message CYCLE ARMS may appear if the cart lifter is nt in the READY TO WEIGH psitin. Repsitining the cart lifter arm t the nrmal Ready t Weigh psitin will return the display t READY TO WEIGH. 3. Verify Arm Angle Sensr T verify the Arm Angle sensr is respnding crrectly, first enter the Setup & Calibratin Mde as described earlier and use the SELECT key t lcate the TROUBLESHOOT display. Weigh-In-Mtin Windw Press the PROGRAM key tw times t lcate the TROUBLE POSITION ptin and press the SET key t activate. WGH START 00.0 shuld display n the meter display. WGH START is the prgrammable angular set pint where the weigh-in-mtin windw starts the weighing f each lad. If it isn t prgrammed t 00.0, use the PROGRAM keys t reset the angle t 00.0 and press SET t activate the value. Press the SELECT key t display WGH END WGH END is the prgrammable angular set pint where the weigh-in-mtin windw ends the weighing f each lad. If it is nt prgrammed t 75.0, use the PROGRAM keys t reset the angle t 75.0 and press SET t activate the value. 66

67 Initial Startup and Calibratin Prcedures Press the SELECT key t display WGH DUMP WGH DUMP is the prgrammable angular set pint where LadMan stres the recrding f the net lad weight. If it is nt prgrammed t 100.0, use the PROGRAM keys t reset the angle t and press SET t activate the value Custm Adjustment f Weigh-In-Mtin Windw The default weigh-in-mtin angle assignments were derived frm the experience LadMan gained wrking with custmers and learning the mst cmmn sized carts used. Hwever, there are carts that might nt fit the weigh windw f 0, 75 and 100 ; especially larger carts which are taller than the cart tipper and scale. Fr these larger carts, yu will mst likely need t adjust the weigh windw. Here are sme guidelines: Set the WEIGH START angle where the cart is ff the grund 6 t 12. This might be frm 5 t 15. The WEIGH END shuld never be higher than 75. When necessary, the WEIGH END can be set lwer s that the cart des nt start dumping the lad befre the weigh windw has been cmpleted. WEIGH DUMP needs t be at least 10 t 25 abve the WEIGH END set pint. 4. Verify Cart Lifter Lad Cells Respnd Crrectly T verify the ladcells are respnding crrectly, first enter the Setup & Calibratin Mde and use the SELECT key t lcate the TROUBLESHOOT display. Press the PROGRAM key t lcate the TROUBLE LOADCELL ptin and press the SET key t activate. 67

68 Initial Startup and Calibratin Prcedures The message, CH1 SPAN 400,000 shuld be displayed. This is the nrmal sensitivity used fr the CH1 left cart lifter ladcell and shuld nt be changed. SELECT till yu get t CH2 SPAN which shuld als display 400,000. If either f these values is incrrect, use the PROGRAM keys t reset either SPAN and press SET t activate the value. Press SELECT t display CH1 xxxx.x LB where xxxxx.x is the current weight reading f the CH1 ladcell. It is calibrated in LBs r KGs. Mve the cart lifter arms s that the cart lifter plates are in the vertical psitin and verify the CH1 and CH2 ladcells are reading near 0 lbs. Hang a lad n the cart lifter r push n it and bth CH1 and CH2 ladcells shuld g psitive. If nt, then yu need t swap the CH1 and CH2 ladcell cnnectrs n the Cart 310 Electrnics Bx. 5. Calibrate Cart Lifter Arm Angle If nt already dne, begin this prcedure by first cycling the arms until the message READY TO WEIGH is displayed. Enter the Setup & Calibratin Mde. Press the SELECT key until SET ZERO?--->NO is displayed. Press the PROGRAM key until ZERO ARM ANGLE? is displayed and then press SET t activate. The display nw shws several sequential messages; THIS IMPACTS YOUR CALIBRATION and PROCEED?---->NO. Use the PROGRAM key t chse YES, and activate with the key. SET LadMan displays, POSITION ARMS TO ZERO ARM ANG and READY?----->NO. Mve the cart lifter arms till the cart lifter munting plates are perfectly vertical (recmmend using a level fr this step), t set the arm angle sensr t read zer at this psitin. 68

69 Initial Startup and Calibratin Prcedures Once the arms are in psitin, use the PROGRAM key t chse YES, and activate with the SET key. LadMan displays, ZEROING ARM ANG! while it is reprgramming the start psitin f the weigh-in-mtin windw; and is finished ZERO COMPLETE is displayed. T verify this prcess wrked crrectly, enter the TROUBLE POSITION prtin f the TROUBLESHOOT display: Nw verify that the ARMS xxxxx.x DEG reads very near zer degrees when the cart lifter munting plates are perfectly vertical. Furthermre, the arm angle (ARMS) shuld becme mre psitive when the arms are raised higher. If the arm angle reads negative (-) as the arms are raised, yu will be able t crrect this errr in Step Verify Angle Measurements Respnd Crrectly Verify Cart Lifter Arm Angle Respnse Enter the TROUBLE POSITION prtin f the TROUBLESHOOT display. Press the SELECT key until the display reads, ARMS xxxx.x DEG. Lift a cart frm the grund until the arm angle reads 0.0 degrees. The cart lifter munting plates shuld be perfectly vertical when the arm angle reads zer degrees. Als, the arm angle shuld increase as the arms are raised and decrease as the arms are lwered. If s, ten prceed t Step 7. If the directin is wrng, tggle the arm directin sign: ARM DIRECTION = +/- This display shuld be used if the arm angle des nt increase in value when the arms are raised. If the arm angle decreases when the arms are raised, then the ARM DIRECTION sign shuld be reversed by using the PROGRAM key t chse YES, and activate with the SET key. 7. Verify Weigh-In-Mtin Respnse T verify the weigh-in-mtin respnse, first exit the Setup & Calibratin Mde: Use the SELECT key and chse the display, EXIT SETUP?-->NO. Use the PROGRAM key t change NO t YES and press SET t activate. LadMan shuld nw be in the Nrmal Operating Mde. The display shuld nw read, READY TO WEIGH!. 69

70 Initial Startup and Calibratin Prcedures Raise the cart tipper up thrugh a cmplete weighing cycle. If everything is wrking prperly the system shuld respnd with the fllwing: WEIGHING LOAD! while the arms are in the weigh-in-mtin weighing windw. GROSS xxxxx LB as the arms pass the end f the weigh-in-mtin windw. DUMP xxxxx LB and LOAD xxxxx LB (alternating) when the arms pass up thrugh the dump set pint. This message indicates that the recrd lad data and aut accumulatr functins have been activated. Nw lwer the cart tipper and the display shuld shw: LOWER ARMS while passing dwn thrugh the dump set pint. WEIGHING TARE as the arms pass dwn thrugh the weighing windw. NET xxxxx LB after the arms have passed belw the start pint f the weigh-in-mtin widw. This is the net paylad that was measured and dumped int the vehicle. RECORDING WEIGHT! indicates that the weighing prcess is cmplete and the lad has been recrded. In a few secnds LadMan will indicate that it is ready fr the next lad with the message, READY TO WEIGH!. If all f this has wrked crrectly, prceed t the next step. If nt, return t step 3, Verify Angle Sensrs are Respnding Crrectly, and red the prcess until all is perfrming crrectly. Fine Tuning Ladcell Accuracy LEARN ZERO LEARN ZERO? Learn Zer is the prcess f custm learning the zer respnse f the cart tipper s ladcells; fine tuning the accuracy f each ladcell. This is accmplished by a series f lifts (12-15 lifts are recmmended). Withut this prcedure the ladcell measurements culd be inaccurate and misleading. The prcess is quite simple. Just fllw the LadMan display instructins: Activate with the SET PROGRAM key. REMOVE CART! Remve the cart fr the entire LEARNING prcess. RAISE ARMS! LEARNING ZERO UP LOWER ARMS! LEARNING ZERO DN CYCLES Displays the number f LEARN cycles cmpleted. 70

71 Initial Startup and Calibratin Prcedures The abve prcess shuld be repeated frm times t allw LadMan t fully determine each ladcell s zer respnse; fine tuning the accuracy f each ladcell. When finished repeating this prcess, simply let the cart lifter rest at zer. LadMan will prvide screen instructins t cmplete the LEARN prcess: UPSELECT IF DONE - SELECT. SAVE ZERO? Use the PROGRAM prgramming key t chse YES, and cnfirm with the SET PROGRAM key. SAVING ZERO DATA Wait fr LadMan t prcess befre activating any further keys. 8. Calibrate System Under Lad LEARN SPAN? Learn Span is the prcess f custm learning the calibratin f the cart tipper s ladcells. This is accmplished by a series f lifts (12-15 lifts are recmmended). Withut this prcedure the ladcell measurements culd be inaccurate and misleading. The prcess is quite simple. Just fllw the LadMan display instructins: Activate LEARN SPAN with the SET PROGRAM key. ENTER SPAN CAL (Factry default is 400LB). Press SELECT key t cntinue. ENTER CAL LOAD This is the calibrated weight f a cart laded with a knwn scale weight frm anther calibrated scale. This lad shuld be tightly secured within the cart fr safety, and t make certain there is n abrupt buncing f the cntainer s cntents during the calibratin prcedure. Use the / PROGRAM prgramming keys t enter the weight reading btained frm the calibrated scale. Press the SET PROGRAM key t save, and press SELECT key t cntinue. LadMan will respnd with LOAD CAL WEIGHT! and has initiated the LEARN SPAN calibratin prcess: RAISE ARMS! LEARNING SPAN UP LOWER ARMS! LEARNING SPAN DN 71

72 Initial Startup and Calibratin Prcedures CYCLES Displays the number f LEARN cycles cmpleted. The abve prcess shuld be repeated frm times t allw LadMan t fully determine each ladcell s span; fine tuning the calibratin f each ladcell. When finished repeating this prcess 12 t 15 times, simply let the cart lifter rest at zer. LadMan will prvide screen instructins t cmplete the LEARN prcess: UPSELECT IF DONE - SELECT. SAVE SPAN? Use the PROGRAM prgramming key t chse YES, and cnfirm with the SET PROGRAM key. SAVING SPAN DATA Wait fr LadMan t prcess befre activating any further keys this may take few mments. Calibrate System fr ZERO CART LIFTER LOAD Begin this step by entering the INSTALL sectin f the Setup & Calibratin Mde and prgram the LadMan meter t SHOW NEGATIVE WEIGHTS by chsing YES. (Later, after cmpleting this calibratin, the meter can be reprgrammed t hide negative net weights if desired.) In rder t btain the mst accurate calibratin results, advance frward t the INSTALL/SET DISPLAYS sectin and set the COUNT BY value t ne (1); using the PROGRAM key t chse 1, and activate with the SET key. Remve any cart ff the cart lifter, EXIT SETUP, and return t nrmal perating mde. With LadMan shwing READY TO WEIGH, press the SELECT key t find the PROGRAM FUNCTION display. Press the PROGRAM key t lcate the ZERO CART LOAD display; press SET t activate; and fllw this prcedure: LadMan starts this prcess with the messages REMOVE CART LOAD and SET ARM ANGLE = 0. Psitin the cart lifter arms until the arm angle is within a degree f zer. LadMan will prvide instant feedback n the current Arm± angle. When the arm angle is within a degree f zer fr a cuple mments, LadMan stps prviding ± angle feedback and displays ZERO COMPLETE indicating the prcess cmpleted successfully. Try a few lifts with n cart n the cart lifter and yu shuld read zer ging up and zer cming dwn r very clse t that. 72

73 Initial Startup and Calibratin Prcedures Calibrate System fr ZERO CART LIFTER LOAD Switch LadMan als features a ZERO CART LOAD switch that is munted n the left utside plate f the cart lifter scales. This light/switch allws the peratr t wrk at the rear f the truck, reading the green strbe light while leveling the cart arm angle t zer. Depressing this switch initiates the zer lad prcess that was just described abve. And it als features a green light strbe that prvides real-time feedback n the cart angle. The clser the angle t zer, the faster the light flashes. And when the frk angle is between 0 and +/-1, the light will hld steady. When finished, the light prvides a high frequency chattering strbe indicated that the Zer Weight is calibrated accurately. When finished, depress the switch t turn ff the light and the zering prcess. Calibrate Cart Lifter Grss Ging Up Verify that the cart lifter lad measured ging up is calibrated t zer. Begin this prcess in the READY TO WEIGH state. With n lad n the cart lifter, slwly raise the cart lifter arms thrugh the weighing windw t verify if the GROSS xxxxx LB measurement ging up is zer. Perfrm several slw lifts ging up t find an average grss weight. If zer, then skip this next calibratin step. If the average grss weight ging up is nt zer, the meter shuld be finetuned t allw fr the variance frm zer. G t the TROUBLESHOOT sectin f the Setup & Calibratin Mde and chse the sectin titled TROUBLE CAL. This calibratin adjustment will ALWAYS be listed in punds even when LadMan is using KG in the nrmal perating mde. Fine tune the ZEROUpCAL setting t accunt fr the average grss 73

74 Initial Startup and Calibratin Prcedures weight variance. Fr example, if the average grss weight is +10 LB ging up, then increase the ZEROUpCAL by 10 cunts frm the current setting. (In KG mde, change the cunt 2.2X larger than the LB mde value displayed.) Fr this example prgram ZEROUpCAL t 10 using the PROGRAM keys, and activate with the SET key. After prgramming the adjustment EXIT SETUP; return t the READY TO WEIGH state. Verify that the GROSS xxxxx LB averages zer (0) ver several slw test weights. Repeat this prcess until an average reading f zer is measured. Calibrate Cart Lifter Net Ging Dwn After LadMan returns t the READY TO WEIGH display, verify if the arm lad ging dwn is calibrated t zer: With n lad n the cart lifter, slwly raise, and then very slwly lwer the arms thrugh the weigh-in-mtin windw t verify if the NET xxxxx LB measurement ging dwn is zer. D several measurements ging dwn t find an average net weight. If zer, then skip this next calibratin step. If the average net weight ging dwn is nt zer, the meter shuld be finetuned t allw fr the variance frm zer. G t the TROUBLESHOOT sectin f the Setup & Calibratin Mde and chse the sectin titled TROUBLE CAL. This calibratin adjustment will ALWAYS be listed in punds even when LadMan is using KG in the nrmal perating mde. Fine tune the ZERODnCAL setting t accunt fr the average net weight variance. Fr example, if the average net weight is +10 LB ging dwn, then adjust the ZERODnCAL 10 cunts frm the current setting. (In KG mde, change the cunt 2.2X larger than the LB mde.) Fr this example, prgram ZERODnCAL t 10 (ten) 10 using the PROGRAM keys, and activate with the SET key. After prgramming the adjustment, EXIT SETUP; and return t the 74

75 Initial Startup and Calibratin Prcedures READY TO WEIGH state. Verify that the NET xxxxx LB averages zer (0) ver several slw test weights. 9. Fine Tune Span Adjust This step requires a laded cart with a knwn weight; s have a cart weighed n a knwn accurate scale. The cart shuld be laded with a gd size weight that represents at least 80% f the cart lifter s capacity. This lad shuld be tightly secured within the cart fr safety, and t make certain there is n abrupt buncing f the cntainer s cntents during the calibratin prcedure. When LadMan is READY TO WEIGH, pick up the laded cntainer and mve thrugh the weigh-in-mtin windw at a slw speed. D this several times t btain the average GROSS xxxxx LB reading ging up and nte this average grss weight reading. Next, perfrm a span truck calibratin prcess. Use the PROGRAM key t select SPAN TRUCK? and activate with the SET PROGRAM key. LadMan respnds with directins t ENTER METER LOAD. Use the prgramming keys t enter the average f weight readings that were just btained frm the LadMan meter. Press the SET PROGRAM key t save. Press the SELECT key and LadMan will respnd with the directins, ENTER CAL LOAD. Use the prgramming keys t enter the weight reading btained frm the calibrated scale. Press the SET PROGRAM key t save. Nw press the SELECT key and LadMan will respnd with the directins, DO AUTOCAL?-->NO. This display is cnfirming that the weights have been entered prperly. T cnfirm that the weight entries are crrect, select YES and press SET. LadMan will nw cmplete the SPAN calibratin and cnfirm with, DOING SPAN ADJUST and SPAN COMPLETE!. EXIT SETUP and return t the READY TO WEIGH state. At the READY TO WEIGH state, slwly pick up an empty cntainer and mve up thrugh the weigh-in-mtin windw. 75

76 Initial Startup and Calibratin Prcedures Lwer the cntainer dwn thrugh the weigh-in-mtin windw at the slwest speed. D this several times t btain an average NET xxxxx LB reading ging dwn. If the NET reading is nt zer (0) then use t the TROUBLE CAL sectin f the TROUBLESHOOT Setup & Calibratin categry t either increase r decrease the SPANDnCAL value t crrect the errr using the rati calculatin: Rati = Grss Weight Ging Up (Grss Weight Up Net Weight Dwn) Fr example, if the average ging dwn NET weight reading is +20 LB and the average ging up GROSS reading was 720 LB, then the system ging dwn is measuring nly = 700 LB. S the SPANDnCAL value needs t be adjusted by the rati: = Reprgram SPANDnCAL by multiplying the current SPANDnCAL value times(x) the weight rati. Then EXIT SETUP. Cntinue this calibratin prcess until the weights ging up and ging dwn are equal, and the empty cart NET xxxxx LB reading is zer (0). Once this calibratin prcedure is cmpleted, the SPANUpCAL and the SPANDnCAL values may nt be equal, but they shuld nt be different by mre than 500 cunts fr a system that is perating prperly. REMINDER During these calibratin prcedures, COUNT BY was prgrammed t 1 and SHOW NEGATIVE WTS was set t YES. Reprgram either r bth these values (if desired) fr the nrmal perating f the weighing system. 76

77 Trubleshting Guide TROUBLESHOOTING GUIDE This sectin f the manual prvides a guide t trubleshting cmmn issues with the LadMan Cart Lifter Weigh-In-Mtin System. It is assumed that the reader has already becme familiar with using the prgramming keys and understands hw t access Setup & Calibratin functins that are all detailed in the chapter titled Setup & Calibratin Mde. LadMan must receive all sensr signals in rder t display the valid weighing display message READY TO WEIGH. The fur sensr signals are: Left Cart Ladcell Signal Right Cart Ladcell Signal Cart Arm Angle Sensr Signal If any f these signals are nt detected, then LadMan suspends all weighing functins and enters int a Trubleshting Diagnstic Mde. When LadMan enters this mde, ne t three diagnstic messages will be displayed: NO ARM SENSOR! r ARM SENSOR OK! NO RGHTCART SIG! r RGHTCART SIG OK! NO LEFTCART SIG! r LEFTCART SIG OK! 1. NO ARM SENSOR! This message is displayed when there is n cmmunicatin t the arm weigh-inmtin sensr. The arm weigh-in-mtin assembly (ARM310) cntains a micrcmputer and arm angle sensr. The micrcmputer cmmunicates the cart lifter arm angle measurement t the LadMan CART310 bx munted between the cart lifter plates. The CART310 sends all the results t the in-cab meter fr prcessing and display. If LadMan cannt detect the arm assembly micrcmputer, then there are three pssible surces t the prblem: 77

78 Trubleshting Guide a) The cable cnnectin frm the CART310 Bx t the arm weigh-inmtin assembly bx has failed r is nt cnnected. b) The arm weigh-in-mtin assembly has failed. This unit is a ptted assembly t survive harsh utdr envirnments. The unit is nt fieldrepairable and must be replaced r rebuilt. c) The LadMan meter has failed. The meter is nt a field-repairable fr this type f cmmunicatin failure. It must be replaced with a new r rebuilt unit. 2. NO LEFTCART SIG! and NO RGHTCART SIG! If these tw messages are displayed, first make certain that the cable cnnecting the LM310 Ladman Meter is prperly cnnected t the CART 310 Bx munted between the cart lifter plates. a) The CART310 weigh-in-mtin assembly cntains the digital t analg cnverters fr bth the right and left cart lifter ladcells and receives the cart lifter arm angle frm the arm sensr bx (ARM310) munted n the cart lifter arms. Check the cable that cnnects the LadMan meter (LM310) t the CART310 bx munted between the cart lifter munting plates. b) If the cables are cnnected securely, then check the cable harness fr damage and perfrm a cntinuity check. c) If the cable is OK but the messages NO LEFTCART SIG! and NO RGHTCART SIG! still display: Attempt t discnnect bth ladcell cables that plugged int the CART310 weigh-in-mtin bx t eliminate a fault in ne r bth f the ladcells. If after unplugging bth ladcells the messages NO LEFTCART SIG! and NO RGHTCART SIG! still displays, then the CART310 weigh-inmtin bx has mst likely failed r the LadMan Meter (LM310). The CART310 weigh-in-mtin mdule is a ptted assembly t survive harsh utdr envirnments. The unit is nt field-repairable and must be replaced r rebuilt. 78

79 Trubleshting Guide 3. NO LEFTCART SIG! but RGHTCART SIG OK! LEFTCART SIG OK! but NO RGHTCART SIG If ne f the ladcell signals is present but the ther is nt, then it is mst likely that ne f the ladcells has failed. Swap the tw ladcells n the weigh-inmtin assembly and see if the errr message reverses. If it des, then ne f the ladcells has failed. Swap the ladcells again t make certain which ladcell has failed. When islated, replace the failed ladcell. 4. Lad Measurements Inaccurate Lad measurements that are nt repeatable r are inaccurate can be traced t ne f the fllwing: One r bth ladcells have failed. The CART310 digital t analg cnverter (CanCder) has failed. Cart arm angle measurements are faulty. Check Ladcell Respnse and CART310 CanCder Press the PROGRAM key t lcate the TROUBLE LOADCELL ptin and press the SET key t activate. Press SELECT t display CH1 xxxx.x LB where xxxxx.x is the current weight reading f the CH1 ladcell. Mve the cart lifter t zer arm angle, which will cause the plates t be in a vertical psitin. The CH1 lad shuld read near zer (0) weight Pick up an empty cntainer and verify that the ladcell respnds in a psitive directin. If the ladcell respnds in a negative directin under lad, then swap the ladcell cnnectrs n the CART310 Bx as they are cnnected t the wrng ladcell cnnectrs. If the ladcell reading is buncing hundreds (100 s) f cunts, drifting, r will nt repeat the same reading under a given cntainer lad, then: either the ladcell has failed; r the cart lifter CART310 weigh-in-mtin analg t digital cnverter has failed; r a ladcell cable has been damaged; r the cnnectr is lse and has misture/dirt in the cntacts. Check fr damaged ladcell cables r dirty cntacts. If the cntacts are dirty then the pins shuld be cleaned with isprpyl alchl and a Q-tip. The signals n these pins are n the rder f less than ne millinth f a 79

80 Trubleshting Guide vlt s any film residue r misture n the cntacts can cause the ladcell signals t drift wildly. If the prblem persists after cleaning the cntacts then the Cart310 CanCder weigh-in-mtin bx shuld be replaced. If replacing the Cart310 weigh-in-mtin bx des nt fix the prblem then the ladcells shuld be replaced. Press SELECT t display the message, CH2 xxxx.x LB and repeat the abve prcedure fr the CH2 ladcell. Checking Cart Lifter Arm Angle Measurements LadMan relies heavily n the accuracy f the cart lifter arm angle measurement t determine accurate weight measurement results. The ladcell weight measurement respnse is influenced by the cart lifter arm angle. Any errr in the arm angle will have a majr effect n the verall accuracy f the weighing system. Furthermre, the arm angle infrms LadMan when t lk at the cart lifter ladcell signals. Any errr in the arm angle can cause LadMan t lk at the ladcell weight measurement respnse in the wrng part f the weighing cycle. T check n the arm angle calibratin: While still in the TROUBLE POSITION ptin f the TROUBLESHOOT Setup & Calibratin categry, view the current arm angle, ARMS xxxx.x DEG. The arm angle shuld read zer degrees when the cart lifter has lifted the cart ff the grund near a ft. If nt, then gt t step 5 f the Initial Startup and Calibratin Prcedures and fllw the directins fr calibrating the arm angle. 80

81 Cllecting Lad Data COLLECTING LOAD DATA When a lad is recrded, lad data is stred int LadMan s data cllectin memry. The lad infrmatin is recrded and stred as shwn in Table 12. LOAD DATA Table 12. Recrded Lad Data CONDITIONS FOR RECORDING DATA Date & Time Lad Name Accunt Number Stp Number Cntainer Grss Weight Lad Weight (Dumped Lad) Cntainer Net Weight (Empty) Net Truck Weight (Paylad Weight) Prduct Event GPS Crdinates Optinal (INSTALL/DISPLAYS/ACCOUNTS) Optinal (INSTALL/DISPLAYS/ACCOUNTS) Optinal (INSTALL/DISPLAYS/PRODUCT) Optinal (INSTALL/DISPLAYS/EVENT) If GPS mdem and signal available After each recrding f a lad, LadMan sequences (when aut sequence enabled) t the next Stp Number and its crrespnding Lad Name and Accunt Number, and is therefre autmatically set up fr the next cllectin. Out-f-Sequence r Unplanned Cllectins It may smetimes be necessary t cllect a lad ut-f-sequence r t recrd a lad that was unplanned during a cllectin rute. There are several ptins available thrugh the frnt panel PROGRAM buttns fr these and similar situatins. 81

82 Cllecting Lad Data Prgramming the STOP# Display If a printed cpy f the rute schedule is available, then the stp numbers will be listed fr each stp n the rute. Use the rute schedule t find the stp number f the accunt that needs cllected and recrded ut-f-sequence. Then use the SELECT and PROGRAM frnt panel keys t select the new stp number befre recrding a lad. Fr example, LadMan is currently displaying STOP #45, but instead, STOP #198 needs t be cllected and recrded. Using the / SELECT keys, lcate the STOP # display; then use the / PROGRAM keys t change #45 t #198. This will direct LadMan t g directly t Stp #198 and the crrespnding lad name and accunt number fr the stp. If a stp number is entered that is nt fund in the rute list (i.e., a stp number that is higher than any n the list) then LadMan will display the highest stp number in the rute list. Prgramming the ACCOUNT # Display If the accunt number is knwn, use the SELECT and PROGRAM frnt panel keys t enter the accunt number befre recrding the lad. Then, when the SET PROGRAM key is pressed, LadMan will search the dwnladed rute list fr the entered accunt number. If the accunt number is fund in the dwnladed rute list, LadMan will display/cnfirm with the assciated stp number and accunt number. If the accunt number is nt fund in the dwnladed rute list, then LadMan autmatically creates the new accunt and displays the message CREATING ACCOUNT ; fllwed by the display f a new stp number and the newly created accunt number. The new stp number will be added t the dwnladed rute list, alng with the new accunt number, and a newly created lad name UNPLANNED STOP XX ; where XX represents the number f unplanned stps in memry. This new stp number, accunt number and lad name will be added after the last stp in the currently dwnladed rute list. Selecting a Lad Name Using the LOAD NAME Display T select a specific lad name frm the list f dwnladed rute lad names, first use the / SELECT keys t lcate the current LOAD NAME display. The PROGRAM key will sequentially display the next lad name frm the rute list. A flashing curser will indicate that LadMan has entered the Prgram Operating Mde. Pressing the PROGRAM key will sequence frward t the next lad 82

83 Cllecting Lad Data name, while the PROGRAM key will sequence in reverse. PROGRAM key t select and lad a displayed lad name. Press the SET Recrding a Prduct Sme cmpanies will dwnlad rutes that include specific prduct names fr describing their pickup services (e.g., cardbard, recycles, garbage, yard clippings, etc.). T chse and recrd a prduct fr the current Stp #: PRODUCT displays must first be enabled with the SET DISPLAY/FLASH PRODUCT cmmand. Lcate the PRODUCT display using the / SELECT keys. Lcate the particular prduct name using the / PROGRAM keys. Activate the prduct name with the SET PROGRAM key. When the lad is recrded, the prduct name will be recrded int LadMan s data cllectin memry alng with the stp #, accunt name, accunt number and any ther enabled rute ptins. Once a prduct name has been selected, it will remain in effect fr all subsequent lad recrdings. The prduct name shuld be re-prgrammed whenever the prduct cnditin changes. Recrding Unexpected Events Smetimes a prblem/event will ccur in the prcess f picking up r delivering a lad and it is valuable t recrd that event fr a particular rute stp (e.g., n cntainer, rad blcked, gate lcked, etc.). T chse and recrd an Event fr the current Stp #: EVENT displays must first be enabled with the SET DISPLAYS/FLASH EVENT cmmand. Lcate the EVENT display using the / SELECT keys. Lcate the particular prblem/event name using the / PROGRAM keys. Activate the event name with the SET PROGRAM key. When the lad is recrded, the event cnditin will be recrded int LadMan s data cllectin memry alng with the stp #, accunt name, accunt number and any ther enabled rute ptins. Once an Event cnditin has been selected and recrded, it will revert back t the NO EVENT cnditin fr all subsequent lad recrdings. New event cnditins shuld be re-prgrammed anytime an event is encuntered and befre a lad is picked up and recrded. 83

84 Cllecting Lad Data 84

85 Wiring Diagram Wiring Diagram Figure 8. LM310 Wiring Diagram fr Cart Based Weight System 85

86 Errr Messages Appendix A Errr Messages Errr Message ABORTING CAL ABORTING ZERO AUTOCAL ERROR #1 ABORTING TRK CAL NO ARM SENSOR! NO LEFTCART SIG! NO RGHTCART SIG! SECURITY FAILED ZERO COMMAND FAILED Table 13. Table f Errr Messages Cnditin and Pssible Reslutin Prcess fr calibrating the Span has been interrupted. Repeat the prcess. Prcess fr zering arm r lad has been interrupted. Repeat the prcess. When calibratin is attempted, LadMan will make ne final check t make sure things are acceptable. If the SPAN numbers g t zer (0) then there is a prblem. Likewise if the SPAN ges t values greater than 999,999 then there is a prblem. If this ccurs, LadMan abrts the AutCal and reprts an Errr 1 message; meaning that that AutCal failed due t an incrrect entry. Message displayed when there is n cmmunicatin t the Arm Weigh-In-Mtin sensr. See sectin titled Trubleshting Guide. N signal frm the left cart lifter ladcell. See sectin titled, Trubleshting Guide. N signal frm right cart lifter ladcell. See sectin titled Trubleshting Guide. Security passcde is incrrect. Setup & Calibratin cannt be accessed withut a crrect security passcde. Prcess fr zering the ladcells has been interrupted r tk t lng. Repeat the prcess. 86

87 Cell State Cdes Appendix B Setup & Cnfiguratin Cmmand Tree Figure 9. Setup & Cnfiguratin Cmmand Tree 87

88 Cell State Cdes Figure 10. Setup & Cnfiguratin Cmmand Tree (Page2) 88

89 Cell State Cdes TROUBLESHOOT TROUBLE CAL? ZEROUpCAL xxxxxx ZERODnCAL xxxxxx SPANUpCAL xxxxxx SPANDnCAL xxxxxx SampDevUp xxxxxx SampDevDn xxxxxx SampUpRaw SampUpC1 SampUpC2 SampUpC3 LadUpRaw LadUpC1 LadUpC2 LadUpC3 SampDnRaw SampDnC1 SampDnC2 SampDnC3 LadDnRaw LadDnC1 LadDnC2 LadDnC3 NetRaw NetC1 NetC2 NetC3 TROUBLE POSITION TRB LOAD RECORDS WGH START x.x WGH END x.x WGH DUMP x.x ARM DIRECTION= -/+ ARMS x.x DEG ARM ZERO -/+xx ArmSTRTup x.x ArmENDup x.x ArmENDdn x.x ArmSTRTdn x.x Trace TraceLst RECORDS xxxxxx ERASE CTR x Figure 11. Setup & Cnfiguratin Cmmand Tree (Page3) 89

90 Cell State Cdes Figure 12. Setup & Cnfiguratin Cmmand Tree (Page4) 90

91 Cell State Cdes Appendix C Cell State Cdes and Descriptins Table 14. Cell State Cdes and Descriptins Cde Descriptin & Meaning 0 Mdem nt detected 1 TCPInit is attempting 1st try t get an "ate" Respnse. 2 TCPInit is attempting 2nd try t get an "ate" Respnse. 3 Gd ate respnse, starting SIM Card Read 6 SIM Card Number agrees with the ne previusly Stred in Flash Memry 7 New SIM Card Number was detected. Flash Memry was erased and the New SIM Card Number was stred t Flash Memry 10 N respnse t attempt t startup mdem 11 Mdem did nt pen, Stpping Stack 12 Mdem did nt pen, Restarting Stack 20 Mdem is ready t accept all AT Cmmands 21 Mdem did nt respnd t 100ms Segmentatin Cmmand 30 Open GPRS Bearer 31 GPRS Bearer failed t Open 40 Set GPRS APN Name fr USA r Canada 41 Mdem failed t receive APN Name 50 Start GPRS Bearer 51 GPRS Bearer failed t start 60 Create TCP Client n IP Prt Mdem failed t Create a TCP Client 70 Cnnected, setup t start exchanging data 80 Cnnected t Remte IP and in Data exchange mde 81 Respnding t an Identify cmmand frm LFM 82 Mdem did nt Respnd prperly t Cmmand Mde Cmmand 83 Mdem did nt respnd prperly t Discnnect Cmmand 84 Mdem did nt respnd prperly t Stack Clse Cmmand 85 Received <esc>tke Cmmand - Erase Data 86 Received <esc>tkd Cmmand Discnnect 87 Sent Discnnect Cmmand t Mdem 88 Send Clse Stack Cmmand t Mdem 89 Received <esc>tkt Cmmand - Update Time f Day 90 Received <esc>tk1 Cmmand - Start Rute Dwnlad 92 Received Length and Start f Rute Dwnlad 91

92 Cell State Cdes 93 Rute Dwnlad has cmpleted successfully 94 Timeut ccurred during Rute Dwnlad 100 Received <esc>tk2 cmmand - Start Data Dump 110 Respnded t a SIM Card Read 160 Received <esc>tk3 cmmand fr GEO Rute dwnlad 165 Received first 22 bytes &sending ACK cmmand fr Ge Rute Dwnlad 167 Received first 18 bytes &sending ACK cmmand fr Ge Rute Dwnlad 169 Ready t receive blck during Ge Rute Dwnlad 170 End f Ge Rute Dwnlad 190 Ge Rute Lad errr 200 Cmpleted 92

93 Dwnlading LadMan Meter Sftware Appendix D Dwnlading LadMan Meter Sftware A circumstance culd take place that might require an update t the LadMan meter sftware that is running in the LM310 Meter, CART310 Bx and/r the ARM310 Bx. Cnnecting PC/Laptp t LM310 Step1: Install LadMan Lad Management Sftware (LLM) LadMan prvides an unlicensed versin f its sftware as a platfrm fr cnnecting and prgramming the LadMan electrnics like the LM310 and the ARM310. A cpy f this sftware can be btained frm an Authrized LadMan Dealer. Territry dealers are listed n the LadMan website: Step 2: Cnnect Windws PC t LM310 Display There are tw types f cnnectrs t cnnect a Windws PC/Laptp t the LM310 display. A direct serial cnnect between a PC COM prt and the LM310 prt#1 serial prt. <r> A wireless Bluetth cnnectin between a PC COM prt and the LM310 Bluetth prt. A cmmn device t repurpse a USB COM prt t Bluetth is the Parani SD100. Fr ur Figure 13. Parani SD100 USB t 93 Bluetth

94 Dwnlading LadMan Meter Sftware demnstratin, we ll use Bluetth. Step 3: Identify the PC s Serial Cmmunicatins Prt After the serial r Bluetth cnnectr has been attached t the PC, yu must learn the exact COM prt number that is being used by reviewing the Windws Device Manager Table. T access Device Manager, use any f the fllwing (3) methds (depends n which Windws O/S yu are using): Click Windws Start Buttn in lwer left crner Click Run, Then type devmgmt.msc <r> Right-click My Cmputer (smetimes it s simply Cmputer) Click Manage, Then click Device Manager <r> Right-click My Cmputer Click Prperties, Click the Hardware tab, Then click Device Manager. 94

95 Dwnlading LadMan Meter Sftware Within Device Manager, click and pen-up Prts (COM & LPT) Make sure and nte the COM prt listed. (COM3 fr this example). Step 4: Cnfigure COM Prt in LadMan Lad Manager Sftware Nw that the PC Serial COM Prt has been identified, return t the LadMan Lad Manager Sftware t direct LLM t use this COM prt fr cmmunicating t the LM

96 Dwnlading LadMan Meter Sftware Frm LadMan Lad Manager Click Tls Click Cnnectins The Add Cnnectin dialg is displayed with all the currently defined COM prts available fr LLM. We will be using the Bluetth/Parani cnnectins In ur example Nte that BLUETOOTH is currently cnfigured t COM1. T change the cnfiguratin, click n Edit COM3 is nt set-up/defined, s click the Add key t set-up and cnfigure the COM3 prt. 96

97 Dwnlading LadMan Meter Sftware Shwn here is the dialg bx befre setting-up any COM cnnectin details. In the Name Field, chse a name fr the COM prt in ur example, simply call it COM3:9600. The 9600 indicates the baud rate n the prt. Under Baud Rate click n Under Cmm Prt, click n COM3. Ignre the rest f the fields as these defaults wrk fine. Enter OK when cmplete. 97

98 Dwnlading LadMan Meter Sftware CLOSE the Cnnectin table. View the added COM3 prt in the LLM Cmmunicatins Table. Step 5: Cnnect LLM t LM310 Using Terminal Emulatin Make certain that the hst PC that s running LadMan Lad Management Sftware is cnnected t the LM310 s Prt#1. Pwer n the LM

99 Dwnlading LadMan Meter Sftware Initiate the Terminal Cnnect dialg with the LM310 Make certain LM310 Bluetth in turned ON Frm the Lad Manager click n Tls Select Advanced Functins Click n Cnnect Cmm Prt Chse COM prt (in ur example COM3:9600) and click OK. 99

100 Dwnlading LadMan Meter Sftware When yu can view this blank screen, click n Bluetth Query. directing LLM t find the LM310 Bluetth cnnectin. 100

101 Dwnlading LadMan Meter Sftware Nw, highlight the query result and press cnnect Press and hld Ctrl and T keys simultaneusly, until yu see the fllwing menu. Nte the Dnlad buttn at the tp f the display. By clicking this buttn, yu will be asked fr the file name t dwnlad t the LM310 t upgrade any currently stred sftware versin. Fr dwnlading sftware fr upgrading the CART310 Bx r ARM310 Bx, here is a YuTube vide describing the prcedure: VIDEO >> LadMan ARM r CART Bx Sftware Dwnlad 101