PLEASE READ THIS PRODUCT MANUAL CAREFULLY BEFORE USING THIS PRODUCT.

Transcription

1 Features The AVG-HD400 is an HDBT 2.0 transceiver set which contains a transmitter and a receiver. Compliant with HDMI 1.4 & HDCP 2.2, it is able to transmit high-definition signals up to 4Kx2K@60Hz. The extender set supports ARC functionality and can be used stand-alone as an Audio extender. Supports HDMI 1.4 & HDCP 2.2. Is backwards compatible with all previous HDMI standards The highest resolution is up to 4Kx2K@60Hz, and supports 1080p 3D Supports HDBT 2.0, transmits 4Kx2K signals up to 100m and 1080p signals up to 150m via a single CAT5e/CAT6 cable Intuitive front panel switcher control: Transmission Mode (100m/150m), ARC (ON/ OFF) Supports CEC and ARC Separate Audio Balun or ARC deembedding Optical & Analog Audio output Optical & HDMI Audio input Bi-directional IR & RS232 control Supports bi-directional PoH Inbuilt 4 port Ethernet Switch Status LEDs for power, link & HDCP status on front panel

2 PLEASE READ THIS PRODUCT MANUAL CAREFULLY BEFORE USING THIS PRODUCT. This manual is only for operation instruction only, and is not to be used in a maintenance capacity. The functions described in this version are current as at December Any changes of functions and operational parameters will be updated in future manual versions. Please refer to your dealer for the latest product details. Version 1.0 1/12/15

3 SAFETY OPERATION GUIDE In order to guarantee the reliable operation of the equipment and safety of the user, please abide by the following procedures during installation, use and maintenance: 1. The system must be earthed properly. Please do not use two blade plugs and ensure the AC power supply ranges from 100v to 240v and from 50Hz to 60Hz. 2. Do not install the units in an environment where they will be exposed to extreme hot or cold temperatures. 3. These units will generate heat during operation, please ensure that you allow adequate ventilation to ensure reliable operation. 4. Please disconnect the units from mains power if they will be left unused for a long time. 5. Please DO NOT try to open the casing of the equipment, DO NOT attempt to repair the unit. Opening the unit will void the warranty. There are high voltage components in the unit and attempting to repair the unit could result in serious injury. 6. Do not allow the unit to come into contact with any liquid as that could result in personal injury and product failure.

4 TABLE OF CONTENTS Introduction... 1 Introduction to the AVG-HD Features What s in the Box... 2 Product Appearance of the AVG-HD Transmitter Receiver System Connection... 4 System Applications Usage Precautions Connection Diagram Connection Procedure PoH Solution ARC Solution Specification... 5 Supported Resolution Panel Drawing... 6 Troubleshooting & Maintenance... 7

5 1. Introduction 1.1. Introduction to the AVG-HD400 The AVG-HD400 is an HDBT 2.0 transceiver set which contains a transmitter and a receiver. Compliant with HDMI 1.4 & HDCP 2.2, it is able to transmit high-definition signals up to 4Kx2K@60Hz. The HDBT ports support HDBT 2.0, which enable 100m (max) 4K transmission and 150m 1080p transmission as well as bi-directional USB/IR/RS232 signals via single Cat5e/Cat6 cable. Transmission mode is selectable via front panel switches. The extender set boasts 4 Ethernet ports working as an 10/100 Ethernet Switch across the transmitter and receiver LAN ports. The unit is controllable via front panel switches, bi-directional USB, IR& RS232. Furthermore, it also supports ARC function, adding product flexibility Features Supports HDMI 1.4 & HDCP 2.2 and is backwards compatible with all previous HDMI standards The highest resolution is up to 4Kx2K@60Hz, and supports 1080p 3D Supports HDBT 2.0, transmit 4Kx2K signals up to 100m and 1080p signals up to 150m via single CAT5e/CAT6 cable Intuitive front panel switcher control: Transmission Mode (100m/150m), ARC (ON/ OFF) Supports CEC and ARC Audio function Separate Audio Balun or ARC de-embedding Optical & Analog Audio output Optical & HDMI Audio input Bi-directional IR & RS232 control Supports bi-directional PoH Inbuilt 4 Port Ethernet Switch Optical or HDMI Audio Sending from the Receiver (Selectable) Synchronous Analog/Optical Audio Output at Transmitter Status LEDs for Power, link & HDCP status on front panel

6 2. What s in the Box 1 x AVG-HD400 1 x Power Adapter (DC12V 2A) 8 x Screws 4 x Mounting Ears 4 x Plastic cushions 8 x Rubber Feet 1 x User manual Note: Please confirm if the product and the accessories are all included, if not, please contact your dealer.

7 3. Product Appearance of the AVG-HD Transmitter No. Name Description 1 FW Micro USB port, used for firmware updates. Firmware update needs auxiliary equipment, please contact our technical department for more details Power HDCP LINK ON Transmission Mode Switcher ARC Switcher ETHERNET Power indicator: OFF: No power RED: DC power present HDCP compliance indicator: OFF: No HDMI signal (no picture) GREEN: Signal with HDCP Blinking GREEN: Signal without HDCP HDBT Link status indicator: OFF: No Link GREEN: Link successful Blinking GREEN: Link problem Working status indicator: OFF: Not operational Blinking GREEN: Normal operation Activate 100m/150m transmission mode. 100m mode: 4Kx2K@60Hz and 1080P signals can be transmitted up to 100m 150m mode: 1080P signal can be transmitted up to 150m, but does not support a 4K signal. Note: After setting switch position, the mode will not take effect until units are restarted. Please set both ends identical. ON: Enable ARC function OFF: Disable ARC function Ethenet port, work as an Ethernet Switch together with three Ethenet ports on rear panel of Receiver. Connect any one with a router, the other 3 ports are able to access LAN

8 9 HDBT OUT/PoH Connect to the HDBT IN/PoH port on rear panel of the Receiver via CAT5e/ CAT6a cable, compliant with HDBT 2.0 and supports bi-directional PoH 10 HDMI IN Connect with a HDMI source 11 AUDIO OUT Analog audio output port, connect with an AV amplifier to play analog audio which is formatted as PCM 12 SPDIF OUT Digital audio output port, connect with an AV amplifier to play digital audio. 13 IR IN Connect with 5V IR receiver to collect infrared signals, works with the far-end IR OUT port. 14 IR OUT Connect with IR Emitter to send infrared signals, works with the far-end IR IN port. 15 RS232 Serial port, connects with control device or device to be controlled, supports bi-directional RS232 control. 16 DC 12V Connect with a DC12V 2A power adapter. Note: Pictures shown in this manual are only for reference Receiver No. Name Description 1 FW Micro USB port, used for firmware updates. Firmware updates need auxiliary equipment, please contact our technical department for more details. 2 Power Power indicator: OFF:No power RED:DC power present 3 HDCP HDCP compliance indicator: OFF: No HDMI signal(no picture) GREEN: Signal with HDCP Blinking GREEN: Signal without HDCP

9 LINK ON Transmission Mode Switcher ARC Switcher ETHERNET HDBT IN/ PoH HDBT Link status indicator: OFF: No Link GREEN: Link successful Blinking GREEN: Link problem Working status indicator: OFF: Not operational Blinking GREEN: Normal operation Activate 100m/150m transmission mode. 100m mode: 4Kx2K@60Hz and 1080P signals can be transmitted up to 100m 150m mode: 1080P signal can be transmitted up to 150m, but does not support a 4K signal. Note: After setting switch position, the mode will not take effect until units are restarted. Please set both ends identical. ON: Enable ARC function OFF: Disable ARC function Three Ethenet ports, work as an Ethernet Switch together with the ETHERNET port on rear panel of Transmitter. Connect any one with a router, the other 3 ports are able to access LAN. Connect to the HDBT OUT/PoH port on the Transmitter via CAT5e/ CAT6a cable, compliant with HDBT 2.0 and supports bidirectional PoH. 10 HDMI OUT Connect with HDMI (ARC) Port of the display. 11 SPDIF IN Digital audio input port, works with SPDIF OUT on Transmitter. Note: This port only can be used in ARC OFF mode. 12 IR IN Connect with 12V IR receiver to collect infrared signals, works with the far-end IR OUT port 13 IR OUT Connect with IR Emitter to send infrared signal, works with the farend IR IN port 14 RS232 Serial port, connects with control device or device to be controlled, supports bi-directional RS232 control 15 DC 12V Connects with a DC12V 2A power adapter. Note: Pictures shown in this manual are only for reference.

10 4. System Connection 4.1. System Applications Robust performance for control and signal transmission makes the AVG-HD400 ideal in the custom installation industry, IT computer space, signal monitoring, big screen displays, conference systems, television broadcast, education, banking and security institutions etc Usage Precautions 1. System should be installed in a clean environment with temperature and humidity maintained to within equipment specification. 2. All of the power switches, plugs, sockets and power cords should be insulated and safe. 3. All devices should be connected before power is turned on Connection Diagram

11 4.4. Connection Procedure Step 1. Connect a HDMI source (such as Blue-ray DVD) to HDMI IN port of the transmitter with a HDMI cable. Step 2. Connect the HDBT OUT/PoH port of the transmitter to HDBT IN/PoH port of the receiver through a straight-thru CAT5e/CAT6a cable. Step 3. Connect a HDMI display (such as HDTV) to HDMI OUT and SPDIF IN port of the receiver with a HDMI cable and digital audio cable. Step 4. Connect an AV amplifier to AUDIO OUT or SPDIF OUT of Transmitter. Step 5. Connect speakers to the AV amplifier. Step 6. When using the bi-directional IR control, do the following: a. Connect the IR emitter at either end to the IR OUT port on either the transmitter or the receiver. b. When using a powered IR receiver, connect via a 3.5 mm stereo plug to the IR IN on either the receiver or the transmitter. Step 7. When using the bi-directional RS232 control, do the following: a. Connect a control processor to the RS232 port at either the transmitter or the receiver. b. Connect the third-party device (such as a projector) needed to be controlled to the RS232 port at the other end. c. Send RS232 commands to control the unit. For more details about RS232 commands, please refer to the user manual of the third-party device. Step 8. Connect an Ethernet Router to any one of the 4 Ethernet ports to access Ethernet. In this case, PCs connected to the other 3 Ethernet ports should set to static IP. Step 9. Connect with a DC12V power adaptor to the power port of either Transmitter or Receiver, the other end will be powered synchronously via the PoH solution.

12 Notes: 1. System Diagram shown in this manual is for reference only. 2. Connect HDBT ports via straight-thru CAT5e/6 cable with TIA/EIAT568B standard terminations at both ends. 3. RS232 communication protocol: Baud Rate: 9600; data bit: 8; stop bit: 1; parity: none. This product receives RS232 control from devices with various baud rates (2400, 4800, 9600, 19200, 38400, 57600, ). 4. HDBT ports can work with our company s HDBT devices that has same power supply solution. 5. Make sure the switches on front panel are set correctly. 6. Reboot the device if the switch positions status has changed PoH Solution This product HDBT port support s PoH. Besides carrying uncompressed 1080p or 4K video signals, high-resolution lossless audio, Ethernet, and two-way IR or RS-232 control signals over a single Cat 5e/Cat 6 cable, it transfers DC power over a single network cable to a distance up to 150 meters (m) bi-directionally. Connect the DC adapter to either the transmitter or the receiver, the other end is then able to be powered synchronously (see in the following figure): Transmitter L R Tx Rx DC12V 2A Receiver Tx Rx

13 4.6 ARC Solution This product boast ARC (Audio Return Channel) function, which enables a display via a single HDMI cable, to send (upstream) audio to amplifiers/receivers, increasing user flexibility. Please refer to the below figure: Mode: ARC ON L R T x R x T x R x Blu- ray DVD Notes: 1. When using ARC feature, please connect the amplifier via HDMI cable. 2. All utilized devices including the HDMI cable should support ARC. 3. Make sure the ARC switch is switched to ON when using ARC function. 4. When ARC is selected, Optical Audio from the Receive unit will cease to be outputted at the transmitter on both Analog and SPDIF connectors. 5. ARC De-embedded audio is available on both optical and analog connectors at the Transmitter.

14 5. Specifications Model Spec Input Transmitter 1 x HDMI (19 pin Type- A male) 1 x HDBT (RJ45 female) Audio & Video Receiver 1 x HDBT (RJ45 female) 1 x Digital audio (SPDIF) Output 1 x Analog audio (RCA) 1 x Digital audio (SPDIF) 1 x HDMI (19 pin Type-A male) Signal Standard Transmission Mode Audio Format Input HDMI 1.4 & HDCP 2.2 HDMI 1.4 & HDCP 2.2 HDBaseT HDMI Embedded audio: PCM/Dolby Digital/DTS/DTS-HD Analog Audio: PCM Digital Audio: PCM/Dolby Digital/DTS/DTS-HD Control 1 x IR IN (3.5mm mini jack) 1 x IR IN (3.5mm mini jack) Output Other Transmission Distance Temperature Reference Humidity 1 x IR OUT (3.5mm mini jack) 1 x Ethernet (RJ45 female) 1 x RS232 (3-pin pluggable terminal block) 1080p 150m; 4Kx2K 100m 0~ 50 10% ~ 90% 1 x IR OUT (3.5mm mini jack) 3 x Ethernet (RJ45 female) 1 x RS232 (3-pin pluggable terminal block) General

15 Power Supply Power Consumption Input:100V~240V AC Output: DC 12V 2A 6w 8w Dimension (W*H*D) (mm) 196*19* *19*100 Weight (g) Note: All nominal levels are at ±10% Supported Resolutions 4Kx2K 16:9 16:10 4:3 3840x2160 (30Hz/24Hz/25Hz/50Hz/60Hz) 1080P 3D, Note: This product supports 4k &1080p 3D HDMI signals, please use high-quality HDMI cables compliant with HDMI 1.4 for optimum range and performance.

16 6. Panel Drawing Transmitter Receiver

17

18 7. Troubleshooting & Maintenance Problems Causes Solutions No reaction to any operation, power indicator is off Indicator LEDs not functioning correctly Color loss or poor picture quality No video output No digital audio output No analog audio output Cannot use ARC function Units are powered off. Poor quality of network cable. Wrong specification of the power adapter. Signal loss caused by long transmission distance beyond specification. Poor quality HDMI cable. HDMI cables are too long to transmit a 4K HDMI signal successfully. The longest HDMI cable is 8m for 4K input signal, and 20m for a 4K output signal. Communication cable has no connection or a poor connection. The display that you use is incompatible with this device. Input source and output device are connected to the wrong ports. Audio Output device does not support the audio format. Audio OUT port (RCA connector) only supports PCM format. ARC switcher is selected to OFF Devices or cables don t support ARC Insert power adapter at either end. Replace cable with HDBT certified cable. Change to a DC 12V 2A power adapter. Switch the transmission mode switch to 150m, make sure the connecting cable is within 150m and good quality. Ensure the HDMI cables used at the source, transmitter, receiver and display are properly connected and are good quality. Shorten the length of HDMI cables. Recheck all cables and ports. It is recommended that you use a compatible display. Check again and make sure the input source and the output device are connected correctly. Change for another output device that supports the audio formats listed in Specifications. Change for another audio input device that supports PCM format. Select the switch to ON. Change to a device/cable that supports ARC

19 Cannot work as an Ethernet Switch. PCs cannot connect to the internet. Cannot use the device The DHCP switch of the Router is turned on, but the IP address of PCs are static. The DHCP switch of Router is turned off, but the IP address of PCs are dynamic. Network or server failure. Device is faulty Recheck all PCs and set these Pcs to use dynamic IP mode. Recheck all PCs and set these Pcs to use static IP mode and make sure the IP addresses are unique to avoid IP address conflicts. Please contact to your Internet Service Provider. Send it to authorized dealer for repairing.