MODEL NAME: LMCP017TW 03 NV1

Transcription

1 1.77 inch TFT LCD without Touch Panel SPECIFICATION MODEL NAME: LMCP017TW 03 NV1 Date: 2013 / 08 / 27 Customer Signature Customer Approved Date Approved By Reviewed By

2 Revision History Revision Date Originator Detail Remarks First Release Define brightness Define NTSC Ratio(Gamut) Modify structure of frame Page Final check : LEDs in parallel Page LCD weight : 5.5g Page 4 Page 16 2 INTELTRONIC INC.

3 Table of Contents No. Item Page 1. General Description Module Parameter Absolute Maximum Ratings DC Characteristics Backlight Characteristics Backlight Characteristics Optical Characteristics Optical Characteristics Definition of Response Time Definition of Contrast Ratio Definition of Viewing Angles Definition of Color Appearance Definition of Surface Luminance, Uniformity and Transmittance Block Diagram and Power Supply Interface Pins Definition Module interface AC Characteristics Reset timing interface timing Command Table Recommended Setting and Initialization Flow for Reference Quality Assurance Purpose Agreement Items Standard of the Product Visual Inspection Reliability Specification Precautions and Warranty Safety Handling Operation Static Electricity Assembly Drawing Inspection Specifications warranty RMA INTELTRONIC INC.

4 1. General Description This display module is a transmissive type color active matrix TFT(Thin Film Transistor) liquid crystal display (LCD) that uses amorphous silicon TFT as a switching device. This module is composed of a TFT LCD module, a driver circuit, and a back-light unit. The resolution of a 1.77 contains 128(RGB)X160dots and can display up to 65k colors. 2. Module Parameter Features Details Unit Display Size(Diagonal) LCD type α-si TFT - Display Mode TN/ Normally white - Resolution 128 RGB x View Direction 12 O clock Best image Grayscale Inversion Direction 6 O clock - Module Outline 34.7(H) 46.7(V) 2.5 (T) mm TP Outline mm TP Viewing Area TP Active Area Active Area (H) 35.04(V) mm Viewing Area N/A Pixel Size 0.219(H) x0.219 (V) mm Pixel Arrangement Stripe - Display Colors NORMAL WHITE - Interface MCU interface - Driver IC ST7735S - Operating Temperature -20~70 ºC Storage Temperature -30~80 ºC Weight 5.5 g 3. Absolute Maximum Ratings V SS =0V, Ta=25ºC Item Symbol Min. Max. Unit Power supply VCC V Supply Voltage Analog VCI V IO IOVCC V Input Voltage Vi -0.3 IOVCC+0.3 V Storage temperature T ºC Operating temperature Storage humidity Operating humidity stg T ºC op Note 1: 90%RH max, If Ta is below 50ºC; 60%RH max, If Ta is over 60ºC. H stg 10 Note 1 %RH H op 10 Note 1 %RH 4 INTELTRONIC INC.

5 4. DC Characteristics Item Symbol Min. Typ. Max. Unit Power supply VCC V Supply Voltage Analog VCI V IO IOVCC V Logic Low input voltage V IL *IOVCC V Logic High input voltage V IH 0.7*IOVCC - IOVCC V Logic Low output voltage V OL *IOVCC V Logic High output voltage V OH 0.8*IOVCC - IOVCC V Normal display Ivdd ma Current Consumption Standby mode Ivdd ua Frame Frequency f FR - TBD - Hz 5. Backlight Characteristics 5.1. Backlight Characteristics Item Symbol Condition Min Typ Max Unit Forward Voltage V Ta=25 ºC,I F =30mA 3.2 V/LED Forward Current Luminance f I f Ta=25 ºC, V F =3.2V ma L V cd / m Uniformity Avg % X CIE Y Power dissipation P mw d Backlight Driving Voltage VAK V Drive method Constant current LED Configuration 2 White LEDs in parallel Note: Test condition I f =30mA, Ta=25ºC. 5 INTELTRONIC INC.

6 6. Optical Characteristics Backlight On (Transmissive Mode) 6.1. Optical Characteristics Item Symbol Condition Ta=25ºC, VDD=2.8V, TN LC+ Polarizer Specification Min. Typ. Max. Unit 2 LCM/ Display brightness Lv cd / m Luminance on TP Lv viewing angle - TBD - cd/m² surface( I f =30mA) q X = q Contrast ratio(see 6.3) CR Y =0º Response time (See 6.2) Chromaticity Transmissive (See 6.5) Viewing Angle (See 6.4) Red Green Blue White TR+TF Normally ms XR YR XG YG XB YB XW YW Horizont θx al θx Cente 10 θy Vertical θy NTSC Ratio(Gamut) % Deg. 6 INTELTRONIC INC.

7 6.2. Definition of Response Time Normally Black Type (Negative) Relative Brightness Non-selected state Selected state Non-selected state 100% 90% 10% 0% Tr Tf Tr is the time it takes to change form non-selected state with relative luminance 10% to selected state with relative luminance 90%; Tf is the time it takes to change from selected state with relative luminance 90% to non-selected state with relative luminance 10% Normally White Type (Positive) Relative Brightness Non-selected state Selected state Non-selected state 100% 90% 10% 0% Tr Tf Tr is the time it takes to change form non-selected state with relative luminance 90% to selected state with relative luminance 10%; Tf is the time it takes to change from selected state with relative luminance 10% to non-selected state with relative luminance 90%; 7 INTELTRONIC INC.

8 6.3. Definition of Contrast Ratio Contrast is measured perpendicular to display surface in reflective and transmissive mode. The measurement condition is: Measuring Equipment BM-7 or EQUI Measuring Point Diameter 3mm//1mm Measuring Point Location Active Area centre point A: All Pixels white Test pattern B: All Pixel black Contrast setting Maximum Definitions: CR (Contrast) = Luminance of White Pixel / Luminance of Black Pixel 6.4. Definition of Viewing Angles Measuring machine: LCD-5100 or EQUI 6.5. Definition of Color Appearance R,G,B and W are defined by (x, y) on the IE chromaticity diagram NTSC=area of RGB triangle/area of NTSC trianglex100% Measuring picture: Red, Green, Blue and White (Measuring machine: BM-7) 8 INTELTRONIC INC.

9 6.6. Definition of Surface Luminance, Uniformity and Transmittance Using the transmissive mode measurement approach, measure the white screen luminance of the display panel and backlight Surface Luminance: L V = average (L P1 :L P9 ) Uniformity = Minimal (L P1 :L P9 ) / Maximal (L P1 :L P9 ) * 100% Transmittance = L V on LCD / L V on Backlight * 100% Note : Measuring machine: BM-7 X X/6 X/3 X/3 X/6 Display Area Y Y/6 Y/3 Y/3 Y/ INTELTRONIC INC.

10 7. Block Diagram and Power Supply 128RGBx TFT PANEL VCOM Source driver Circuit VCOM Gate Driver Circuit ILI9320 VCC DB0-DB15 CS,RS,RESET. WR.RD. GND ` LED CIRCUIT DIAGRAM: 10 INTELTRONIC INC.

11 8. Interface Pins Definition 8.1. Module interface No. Symbol I/O DESCRIPTION 1 GND p Ground 2 LEDK1 P Back light cathode 3 LEDA P Back light anode 4 LEDK2 P Back light cathode 5 VCC P Analog Supply Voltage 6 ID No Connect 7 IM0 I System interface select. Low: 8-bit bus interface, High: 16-bit bus interface 8 CS I Chip selection 9~24 DB15~DB0 I Data input 25 RD I Read signal 26 WR I Write signal 27 RS I Command/Data select signal 28 RESET I Reset signal 29 IOVCC P Logic Supply Voltage 30~32 NC No Connect 33 GND P Ground 11 INTELTRONIC INC.

12 9. AC Characteristics 9.1. Reset timing Please refer to IC datasheet interface timing MCU interface timing requirement 1 Please refer to IC datasheet 10. Command Table Please refer to IC datasheet. 12 INTELTRONIC INC.

13 11. Recommended Setting and Initialization Flow for Reference. TBD. 12. Quality Assurance Purpose This standard for Quality Assurance assures the quality of LCD module products supplied to customer by Inteltronic display Agreement Items Inteltronic and customer shall negotiate if the following situation occurs: Discrepancies between Inteltronic s QA standards and customer s QA standards Additional requirement to be added in product specification Any other special problem Standard of the Product Visual Inspection Appearance inspection: The inspection must be under illumination about lx, and the distance of view must be at 30cm ± 2cm The viewing angle should be 45 from the vertical line without reflection light or follows customer's viewing angle specifications Definition of area: A Zone: Active Area, B Zone: Viewing Area, Eye Eye A zone B zone Basic principle: A set of sample to indicate the limit of acceptable quality level must be discussed by both Inteltronic and customer when there is any dispute happened. 13 INTELTRONIC INC.

14 13. Reliability Specification Item Condition Cycle Time Quantity Remark Constant Temp. and Constant Humidity Operation Test +40 ± 3ºC,90 ± 3%RH 120hrs -- High Temp. Operation Test +70 ± 3ºC 120hrs -- Low Temp. Operation Test -20 ± 3ºC 120hrs -- *1 Thermal Shock Test -20 ± 3ºC (30min) +70 ± 3ºC (30min) 10cycles -- ESD Test(end product) 150pF, 330Ω, ±2KV, Contact 150pF, 330Ω, ±6KV, Air 10times -- *2, *3 Vibration Test Frequency: 10Hz to 55Hz to 10Hz, One inner 6hrs *4 (for packaging) Swing:1.5mm,time:X,Y,Z each 2H. carton Note 1. For humidity test, DI water should be used. Inspection Standard: Inspect after 1-2hrs storage at room temperature, the sample shall be free from the following defects: Air bubble in the LCD Seal Leakage Non-display Missing Segment Glass Crack IDD is greater than twice initial value. Others as per QA Inspection Criteria Note 2. No defect is allowed after testing The End Product ESD value is only indicative and depends on customer ESD protection design for the whole system Note 3. ESD should be applied to LCD glass panel, not other areas (such as on IC and so on) IDD should be within twice initial value. In case of malfunction defect caused by ESD damage, if it would be recovered to normal state after resetting, it would be judged as a good part. Note 4. Only upon request. 14 INTELTRONIC INC.

15 14. Precautions Safety The liquid crystal in the LCD is poisonous. Do not put it in your mouth. If the liquid crystal touches your skin or clothes, wash it off immediately using soap and water Since the liquid crystal cells are made of glass, do not apply strong impact on them. Handle with care Handling Reverse and use within ratings in order to keep performance and prevent damage Do not wipe the polarizer with dry cloth, as it might cause scratch. If the surface of the LCD needs to be cleaned, wipe it swiftly with cotton or other soft cloth soaked with petroleum IPA, do not use other chemicals Operation Do not drive LCD with DC voltage Response time will increase below lower temperature Display may change color with different temperature Mechanical disturbance during operation, such as pressing on the display area, may cause the segments to appear fractured Static Electricity CMOS LSIs are equipped in this unit, so care must be taken to avoid the electro-static charge, by ground human body, etc The normal static prevention measures should be observed for work clothes and benches The module should be kept into anti-static bags or other containers resistant to static for storage. 15 INTELTRONIC INC.

16 15. Assembly Drawing INTELTRONIC INC. LMCP017TW03NV1 16 INTELTRONIC INC.

17 Reference Item Description Revision ST7735S IC Data sheet V01 LCM assembly drawing R0 17 INTELTRONIC INC.

18 16.Inspection Specifications The buyer (customer) shall inspect the modules within twenty calendar days since the delivery date (the "inspection period ) at its own cost. The results of the inspection (acceptance or rejection) shall be recorded in writing, and a copy of this writing will be promptly sent to the seller. The buyer may, under commercially reasonable reject procedures, reject an entire lot in the delivery involved if, within the inspection period, such samples of modules within such lot show an unacceptable number of defects in accordance with this incoming inspection standards, provided however that the buyer must notify the seller in writing of any such rejection promptly, and not later than within three business days of the end of the inspection period. Should the buyer fail to notify the seller within the inspection period, the buyer's right to reject the modules shall be lapsed and the modules shall be deemed to have been accepted by the buyer. 17. Warranty Inteltronic Inc. warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for one year from the date of purchase. Inteltronic Inc. will be limited to replace or repair any of its module which is found and confirmed defective electrically or visually when inspected in accordance with Inteltronic Inc. general module inspection standard. This warranty does not apply to any products which have been on customer s production line, repaired or altered by persons other than repair personnel authorized by Inteltronic Inc., or which have been subject to misuse, abuse, accident or improper installation. Inteltronic Inc. assumes no liability under the terms of this warranty as a consequence of such events. If an Inteltronic Inc. product is defective, it will be repaired or replaced at no charge during the warranty period. For out-of-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight. In returning the modules, they must be properly packaged with original package; there should be detailed description of the failures or defect. 18. RMA Products purchased through Inteltronic Inc. and under warranty may be returned for replacement. Contact support@inteltronicinc.com for RMA number and procedures 18 INTELTRONIC INC.

19 Inteltronic Inc. Office: Fax: Address: Union City Blvd Union City, CA Wah Lee Industrial Corp. HSINCHU OFFICE 18F, No.8, Zihciang S. Rd., Jhubei, Hsinchu 302, Taiwan, R.O.C. Tel : FAX: INTELTRONIC INC.