Channel processing equipment

Transcription

1 Technical specifications Type sdi480 RF input 4x QPSK / 8PSK COFDM / QAM frequency range MHz MHz level/impedance dbµv / 75 Ω dbµv / 75 Ω symbol rate 2 45 Ms/s - LNB powering/control 0/14/18 V & 300 ma max. DiSEqC DC output for preamplifier - 12 V 100 ma max. IP output standard IEE /100 Base T bit rate up to 400 Mbps up to 200 Mbps transmission protocols UDP/RTP multicast Yes MPTS Yes SPTS Yes Management port standard IEE /100 Base T Supply voltage 12 V ± 1 V Current consumption without external DC feeding 0.7 A 0.5 A Current consumption with max. external load 3 A 0.6 A Operating temperature range 0 o +50 o C Dimensions/Weight (packed) 48.5x198x107.5 mm/0.97 kg 36x198x107.5 mm/0.84 kg Channel processing equipment DVB to IP streamers sdi480, 1. Product description DVB-S/S2 (sdi480), DVB-T/T2/C (), to IP streamers (in text - module) designed to broadcast in multicast on an IP network the services (TV or Radio programmes) issued from FTA or encrypted digital reception. The IP streams can be viewed using an IPTV set-top box or a software video player. Modules are intended for indoor use only. 2. Characteristics Input: eight (sdi480) or four () DVB multi program transport streams (MPTS). Output: up to 512 (sdi480) or 256 () simultaneous, IP-encapsulated services (TV or Radio programs), with individual multicast addresses and 8 (sdi480) or 4 () MPTS streams. Information filtering of DVB tables. UDP & RTP transmission protocols. Web interface for configuration and setting. SNMP agent for monitoring and alarms. SAP & SDP protocols that facilitate automatic service selection on the user's STB and provide information to external servers. PID filtering. PSI/SI parsing. Transparent ECM & EMM messaging. PAT, PMT and SDT table regeneration. Routing of CAT, EIT, TDT tables. Configurable QoS marking. Configurable Time To Live. TS file streaming from flash. Single cable interface (EN 50494) support. 3. Safety instructions Installation of the module must be done according IEC and national safety standards. Any repairs must be made by qualified personnel. Do not expose this module to moisture or splashing water and make sure no objects filled with liquids, such as vases, are placed near or on the unit. Avoid placing the module next to heat sources such as central heating components or in areas of high humidity. Keep the module away from naked flames. If the module has been kept in cold conditions for a long time, bringing it into a warm environment may cause condensation, so allow it to warm up for no less than 2 hours before plugging into the mains. Ventilation should not be impeded by covering the module, such as newspapers, table-cloths, curtains etc. Mount the module in a vertical position only. If installing in a 19 rack system additional forced air cooling fans may be required (see table "Technical specifications" - operating temperature range). Always allow 10 cm of free space from the top, front and bottom of the unit to enable any heat to be dissipated. Vers Draugystes str. 22, LT Kaunas, Lithuania, tel.: , fax: sales@terraelectronics.com, This product complies with the relevant clauses of the European Directive 2002/96/EC. The unit must be recycled or discarded according to applicable local and national regulations. Equipment intended for indoor usage only. confirms, that this product is in accordance to following norms of EU: EMC norm EN , safety norm EN60065, RoHS norm EN confirms, that this product is in accordance with Custom Union Technical Regulations: Electromagnetic compatibility of technical equipment CU TR 020/2011, On safety of low-voltage equipment CU TR 004/2011.

2 4. External view sdi User management Select this option in "System menu" tab. The user management window is displayed sdi480 3 sdi480 7 Figure 26. User management window This window consits of two tables: "Change password" and "User mamagement". The "Change password" table allows you to change the password. Enter the new password in the "New password" field and confirm the new password retyping it in the "Repeat new assword" field. The change of password will not take effect until you press the "Modify" button. In the "User mamagement" table you can manage users, who will be able to login into the streamer. Enter the new username and password in the appropriate fields, select desired role for user and press the "Add" button to add new user or "Update" button to change settings of the user. User role "Admin" enables the password change function and user management function. User role "User" enables only password change function. Press the "Remove" button to remove user from list Restore defaults Clicking on the "Restore defaults" submenu in the "System menu" tab resets the configuration of the streamer module to the factory default values. The Control and streaming interfaces IP parameters remains unchanged Reset the device Clicking on the "Reset the device" submenu in the "System menu" tab causes the streamer module to restart. 1 DC DC Language If you wish to change the streamer's menu language, select this option in the "System menu" RF TEST 8 2 Figure 1. External view of the streamers 15

3 Figure 24. Import parameters window Click on "Click to select file" and select the file containing the configuration data that you wish to restore on the streamer module. Once you have selected the file, click on the "Upload" button at the bottom of the screen. The upload confirmation window will be displayed Firmware upgrade Device firmware can be upgraded via web browser. Press onto Click to select file button and select firmware binary file. If valid file was selected, a version number of new firmware will be displayed. Otherwise an error message will appear. Press Upload button to upload new firmware to the device. Upload progress bar will appear. A message will be displayed asking to restart the module when the file was sent to the module. New firmware will be programmed into the module only after restart. Module will startup with a new firmware and continue to operate with previous parameters. Additional new firmware features (if any) may need to setup additionally to take affect. Avoid power supply interruption when a programming process is going on. Module has possibility to load software revision history and check availability for new software release. Click onto Check online link. If computer (not module!) has internet access, it will show a list of all software releases with links to binary files. Binary file can be downloaded and saved to computer (see figure 25). After that, use the firmware upgrade method as described above RF input of 4xSAT IF signal, DC output for LNB (sdi480). F sockets. RF input of terrestrial, cable signal DC output for preamplifier (). F socket RF output (input signal loop-through) (). F socket. 3 - ETHERNET - control Ethernet interface. RJ45 socket. 4 - LINK/ACTIVITY (yellow) indicator control Ethernet interface. 5 - status indicator (green). 6 - RESET button. Press this button shortly to restart the module. Press this button for more than three seconds to set default IP address of the control Ethernet interface. 7 - Power distribution bus connector V powering input (screw terminal) streaming Ethernet interface. RJ45 socket ACTIVITY (yellow) indicator of the streaming Ethernet interface LINK (green) indicator of the Ethernet interface A connector for flash. 5. Installation instructions Read the safety instruction first. All settings can be made using the web browser via control Ethernet interface. Disconnect power supply unit from the mains before make all connections of modules. Fasten the module on DIN RAIL or individual holder. Connect all necessary RF, powering and control cables. Connect the 75 load to the unused RF output F sockets. Connect power supply in to mains. Within 5-20 seconds of powering the module will run in normal operation mode. Comments of the front panel indicators: if the link with the control Ethernet interface is established - the LINK/ACTIVITY [4] indicator blinks; when module operating, the status indicator [5] blinks at frequency about one time per second, if the link with the streaming Ethernet interface is established - the LINK [11] indicator glows; if IP streaming is active the - ACTIVITY [10] indicator glows; if no link of the streaming Ethernet interface both indicators of the streaming Ethernet interface not glow. 6. MOUNTING The module or mounting bracket must be fixed with steel screws Ø mm. The screws are not included in a package. Mounting on a wall by screws Mounting on a bracket (supplied) Figure 25. Firmware upgrade and software revision history Perpendicular to the wall Parallel to the wall Figure 2. Mounting of the streamer 14 3

4 DC DC DC Mounting on DIN rail System menu This menu tab contains following submenu items: "Event logs", "Export parameters", "Import parameters", "Firmware upgrade", "User management", "Restore defaults", "Reset the device", "Language" Event logs Move the mouse on the System menu tab then click on the "Event logs" line. The event logs screen will appear Figure 3. Mounting to DIN rail Figure 23. Event logs table Figure 4. Mounting from DIN rail This enables you to see a list of the log messages of the module. Log contents remains after the power loss of module. Events in the log are sorted by time the newest are in the beginning. Information events are shown in blue background, error messages are in red. After switching on the unit, the current date is set to 2000:01:01 and time to When the MPEG stream is received, the information about date and is decoded too, and the values of these parameter are corrected. Local time offset in the log is used from the time parameters table (see Figure 22). Each record has an event type, which can be used to filter particular messages. Just select checkboxes in the Logs filtering table and press apply. Other messages will be hidden. "Export logs" button lets to export all messages to a file. Erase logs button will erase all logs from the system Export parameters All of the data established on the streamer module can be saved onto a backup file. Inversely, the configuration data saved on an appropriate file can be restored on streamer module. Move the mouse on the System menu tab then click on the "Export parameters" line. A window is displayed which allows you to select the action for the data file for the current module configuration. You need to select the "save file to disk" option Import parameters Select this option in "System menu" tab. The Import parameters window is displayed. 4 Figure 5. Mounting or removing to/from DIN rail of plastic spacers (supplied). 13

5 7.7. SNMP settings This menu tab contains the SNMP configuration table. Figure 20. SNMP configuration The description of the "SNMP configuration" table rows. "Read Community" - community name acts as a password that is shared by multiple SNMP agents and one or more SNMP managers. The "Read Community" password is used for read-only access to streamer parameters. "Write Community" - is the password used for read-write access to streamer parameters. "Enable TRAP" - SNMP traps are alerts generated by agents on a managed device. Check this box to enable TRAP generation. The streamer generates traps when the diagnostic message occurs. "TRAP Community" - is the password used for accessing of TRAPS. "Host IP #1","Host IP #2" - IP addresses of hosts with SNMP managers, where TRAPS will be send IP parameters This screen (Figure 21) consists of two tables: "Control interface IP parameters", "Streaming interface IP parameters". The IP parameters tables are used to configure Ethernet connection parameters of both interfaces. 7. Operating 7.1 Initial configuration All modules leave the factory with this control Ethernet interface IP address: In order to avoid conflicts with other IP addresses, it is necessary to perform an initial configuration in local mode. Subsequently, it will be possible to access the modules via the local area network (LAN), either to re-programme it or to check is operating status. The modules leave the factory with the following Control Ethernet interface TCP/IP configuration: IP address of the module: Subnet mask: Default Gateway: To access each module, use a PC or MAC personal computer equipped with an Ethernet card and RJ-45 cable (CAT-5E or CAT-6). The IP address of the PC/MAC must be configured within the following range: (do not use , since this is the IP address of the module to be configured). To start the configuration of the module, open your web browser and type in the following direction: The login prompt will appear on the screen (see Figure 6.). Module can be controlled using any web browser. The exception is Internet Explorer, which must be 10.0 version or higher. Figure 6. Login prompt Access to the site is protected by user name and password. The default user name and password is admin. Enter the user name and password and click on "Login" button. Note: the default password - admin - can (and must) be changed as explained on section During initial configuration you need to change the default control and streaming Ethernet interfaces TCP/IP configuration as explained on section 7.8. Control interface IP address reset to default procedure: press the "RESET" [6] button (Figure 1) for more than 3 seconds and release it. After this operation the control interface IP address will be set to , user name and password set to admin. 7.2 General configuration Initial program screen The first screen that appears when the module accessed contains the "Main" window, which gives general information on the device. Figure 21. IP settings screen [1] [2] The description of the "IP parameters" tables rows. "MAC Address" - the physical address of the module's Ethernet network card is displayed automatically. "IP Address" - enter the IP address that you wish to assign to the module. This address must fall within the range of local network addresses. "Subnet mask" - enter the local network mask. "Gateway" - enter the IP address of this gateway. This information is only required if you want to access the module from the Internet. It is possible to control the module via streaming interface. Check the enable WEB control from streaming interface checkbox to enable this function. Note: for security reasons WEB control from streaming interface should be disabled. [3] 7.9. Common settings In this screen (Figure 22) the table with time parameters is shown. Figure 7. General information screen 12 Figure 22. Time parameters table The "Time parametars" table describes following parameters: Timezone - used for proper time records in logs. Date and time source - a channel for a source of time. It is used for proper time records in logs and has no effect to streaming. All original TDT/TOT (Time Data Table/ Time Offset Table) PID 20 pass directly from input to each output without modification. In the top of each configuration screen you will see a main menu tabs [1]. Using it, you can switch between the different configuration menus. The tab highlighted in yellow shows which menu is active at a given moment. The "System menu" tab contains several submenu. Also common elements for all screens is module title [2] and login information strings [3]. The module title can be changed after pressing the "Change" button in the "Device information" table. Pressing on the "Logout" string you can logout from module control. 5

6 Device information table This shows the data of module: Device model : model of the module. Serial number : serial number of the module. Software version : module software version number. Hardware version : module hardware version number. FPGA version : module FPGA firmware version number. IP 1 : IP address of the control interface. IP 2 : IP address of the streaming interface. System time : current time, synchronized from the TDT table of the input stream. Local time offset can be selected in the "Common settings" tab, see section 7.9. Up time : time passed from last power-up or restart of the module. In the "Common status" table the following parameters are displayed at real time: input bit rate in Mbps, output bit rate in Mbps, processor load in percents, internal temperature in degrees of Celsius, demodulator IC temperature in degrees of Celsius, power voltage in Volts. In the "Diagnostic information" table all module errors and comments, how to eliminate these errors, are displayed. Figure 8. Diagnostic information table with errors 7.3 LNB settings (only in sdi480 module) This screen consists of four tables with appropriate LNB settings and table of the user band settings. The "LNB #1-4 " tables are used to configure parameters of LNB, connected to corresponding RF input of SAT IF signal Streaming settings table This table is used specify common streaming parameters to all output streams. Figure 18. Streaming settings table This table consists of following lines: "Protocol" - the drop down menu offers two options: UDP and RTP/ UDP. UDP is a transport protocol which is not connection oriented and is particularly useful for streaming. RTP/UDP adds extra data fields so that the data flow is served at the correct speed for its projection in real time. "TS packet count" - count of the MPEG2 TS packets in the UDP packet. Can be selected from one to seven. It is recommended to select the value of seven packets. "Time To Live" - a parameter used to restrict the stream multicasting range. A number between 1 and 255 is entered in this box. Each time that an IP stream passes through a router, the TTL is reduced by one unit. The stream will be rejected by any router when the TTL value is reduced to zero. "QoS" - quality of Service. The drop down list offers five differentiated service options or Diffserv. These options relate to the priority that you wish to assign to the streaming packets on their routes through switches or routers that are QoS management capable. QoS values: 1 - Top priority 2 - High priority video 3 - Low priority video 4 - Video and voice 5 - Best effort (best effort made to correctly deliver the video data and the associated audio data) "Send IGMP query messages" - enable of the IGMP query messages transmitting. Enable this function when the streaming output of module is connected to the menageable Ethernet swith with IGMP snooping support. In order for IGMP snooping to function, a multicast router must exist on the network and generate IGMP queries. The tables created for snooping are associated with the querier. Without a querier the tables are not created and snooping will not work. When the IGMP query messages send enabled, the module acts as the multicast router. It is sufficient to enable the IGMP query in one module per one Ethernet switch. Once the different data values have been entered, click on "Update" to conclude the streaming settings SAP/SDP settings table This table is used to configure the announcement and service description SAP/SDP channel. SAP and SDP are two protocols for creating an EPG type program guide. 6 Figure 9. "LNB settings" screen LNB #1-4 tables The "LNB #1-4" tables consist of following parameters: "Title" - the user entered description of corresponding RF input. This title will be used in the SAT input selection box of "RF inputs" table (see section 7.4). "LNB LO frequency" - the LNB local oscillator lower frequency in megahertz. Use 9750 MHz for the universal converter. "LNB HI frequency" - the LNB local oscillator upper frequency in megahertz. This parameter is enabled only when the "LNB power" is set to "Auto". Use MHz for the universal converter. LNB Power power supply of the converter can be set to Off, Auto, 13V, 18V, 13V/22kHz, 18V/22kHz. If Auto is selected, power supply voltage of the converter is chosen according to set polarisation 18V Horizontal, 13V Vertical; if the Frequency of the satellite exceeds the value F=(950+LNB Hi+2150+LNB Lo)/2, the 22 khz signal is switched ON and LNB Hi freq. is selected. Figure 19. SAP/SDP settings table "Enable" - check the box if you wish to transmit the program guide. "Sending period" - introduce the time interval, in seconds, at which the transmitted programmes guide will refresh. "Username" - the name entered will be transmitted on the SAP/SDP channel. "IP address" - multicast address of SAP/SDP messages. It is need to be changed only when your IP receiving equipment use different address. "Group names" - the names of SAP/SDP groups which can be assigned to the output streams. Click on "Update" to save the SAP/SDP channel configuration data. 11

7 The description of the table columns. "Enable" - enable streaming of service. "IP address" - the multicast address required for the stream to be added. The available range is from to , but it is recommended to reduce it from to "IP port" - the IP port required for the stream to be added. The default value is "Service title" - select the service from avaiable input services. In the first line sending of the entire transport stream can be enabled. "Output bitrate" - current output bitrate of stream in kbps. When the streaming Ethernet interface is not connected, all output bitrates will be zero. To confirm the configuration, click on the "Update" button Advanced output settings For advanced users, the possibility exists of opening an additional table with further configuration options related to the output services. To open this table, click on the icon next to the service title. For example: LNB Hi=10,600, LNB Lo=9750, then F=(950+10, )/2=11,725 MHz. When power supply of the converter is set to value different from "Auto" - "LNB HI frequency", Satellite, "Polarisation" rows are disabled and the "LNB LO frequency" value is used for IF frequency calculation. Satellite DISEQC command is used to select the satellite when the switch that supports DISEQC protocol is present. Possible commands: None, SAT A, SAT B, SAT C, SAT D. This parameter is enabled only when the "LNB power" is set to "Auto". "Polarisation" - the polarisation of converter. Can be "Horizontal" or "Vertical". In the figure 9 is settings example of Quattro LNB, connected to all four RF inputs User band frequencies table This table is used for entering user band frequencies of the single cable interface (SCIF) switch, supporting EN50494 standard RF inputs On the sdi480 module eight demodulators can be set up in this section. See figure 10. SAT input - used to switch off demodulator or connect to one of four available RF input. Names of RF inputs can be set in the LNB#1-4 tables (see section 7.3.1). User band - used to select the user band of SCIF switch, connected to corresponding RF input. When no SCIF used, this parameter must be set to "NONE". Input band - used to select the input band of SCIF switch, connected to corresponding RF input. This parameter is enabled when the user band is selected different from "NONE". Input frequency - the frequency of transponder in MHz. Ensure, that SAT IF frequency (FRtransponder - LNB Lo/Hi) fits into demodulator s input frequency range. When the "LNB power" parmeter is set to "Auto", device will try (if possible) to automatically select Lo or Hi frequency to fit into the IF frequency range. Symbol rate - the symbol rate of transponder in ksym/s. Modulation standard allows to select modulation type of DVB-S or DVB-S2. Press Update button to set new parameters. There are various status parameters of input signal right to the Update button. Lock status can have following values: - Inactive, when the input channel (demodulator) is turned off; - Locked, when demodulator is locked to the transponder; - Unlocked, when demodulator is unlocked. This state generates error in diagnostic window as well. If the channel is not used, it s recommended to turn it off instead of leaving unlocked. It will save power consumption. RF level and SNR (Signal Noise Ratio) are measured parameters of input signal. Bitrate is the transport stream s bitrate of the transponder. PER (Packet Error Ratio) shows the ratio of invalid received packets and total received packet. A sign < before the value means, that there was no any errors within that number of packets. To reset PER counters, simply click onto the PER value. Figure 17. Extended settings of output streams table The description of the table rows. "Include EPG informantion" - check this to include EPG infomation from the input stream. "SAP/SDP gruop" - select from the drop down menu the SAP group to which you want to link the service. The group will have been previously created through the SAP/SDP settings table (see Figure 19). "SAP/SDP channel number" - enter the order number you want to assign to the service on the subscriber's set-top box or reproducer, if the device supports SAP. "New service title" - the name given to the service on the subscriber's set-top box or reproducer, if the device supports SAP/SDP protocol. The name that the service has on the input transport stream is the default name. Also this name will be used as the output service name. "New service provider" - enter the provider name of the output stream. This name will be used in the SDT table. Within the "Enable" checkboxes next to the stream PIDs is possible to select the streams to be broadcast for each service (the video PID cannot be disabled). By default, all the PIDs are selected and remain so until this configuration is altered. When you have made your selection, confirm it by clicking on the "Update" button and close the advanced settings table by clicking on the 10 icon. Figure 10. The "RF input" table on sdi480 module On the module four demodulators can be set up in this section. Each demodulator has a corresponding input table. The "Input 1-4" table (figure 11, 12) consist of following parameters: "Enable" - used to switch on/off the demodulator. It is recommended to switch off unused demodulators to save power. "Modulation standard" - used to select from the "DVB-T/T2" and "DVB-C" modulation standards. "Preamplifier power" - used to switch on/off the power for the RF preamplifier. "Input bandwidth" - the bandwidth of DVB-T/T2 transponder. Can be selected from values 8 MHz and 7 MHz. "Input frequency" - the frequency of the terrestrial or cable transponder in kilohertz. When the tuner is locked to the DVB-T2 transponder with multi PLP modulation, the additional parameter "PLP number" is displayed in the "RF input" table. When the "Modulation standard" set to DVB-C, the "Preamplifier power" parameter is hidden and power for the RF preamplifier is switched off; instead of the "Input bandwidth" parameter the "Symbol rate" parameter is displayed. Enter the value in kilo symbols per second. 7

8 Figure 11. The "Input 1-4" table of the module DVB-T/T2 standard Figure 14. screen 7.6. Output settings This screen consists of input channel selection box and three tables: "Output streams","streaming settings" and "SAP/SDP settings". The "Output streams" table is used to individually configure the output streams.the "Streaming settings" table is used specify common streaming parameters to all output streams. The "SAP/SDP settings" table is used to configure the announcement and service description SAP/SDP channel. Module contains eight demodulators and one streaming input from flash. For configuration of output streams select one of eight demodulators named "Input 1-8" or "" in the of input channel selection box. See figure 15. After selection list of services from corresponding input will be shown in the output streams table. Figure 12. The "Input 1-4" table of the module DVB-C standard Once the different data values have been entered, click on Update to conclude the input settings Input status table (only in module) 8 Figure 13. Input status table The following information is displayed in the tables Input 1-4 status (Figure 13). Lock status Locked - the module has synchronised with the input signal; "Unlocked - the module has not synchronised with the input signal. Input level - RF signal level at the module input. Level indication - approximate. The values of the following parameters are displayed only if the streamer module has synchronised with the input signal. Modulation standard - detected standard of the input signal. Possible values of the standard: DVB-T, DVB-T2, DVB-C. Modulation - modulation scheme of the input signal. Possible values of the modulation scheme: QPSK, QAM16, QAM32, QAM64, QAM128, QAM256. SNR - RF signal/noise ratio at the input of module. VBER - bit error rate after Viterbi corrector. To get the signal without any errors at the output of the tuner, VBER shall not exceed 2Е-4. PER - ratio of the MPEG2 transport error packets to the whole number of packets. If the number of error packet is equal to zero, the opposite value to whole number of packets is displayed. Packet counters are reset during RF input parameters update. Input bitrate - bitrate of the input signal This screen (see figure 14) is used to browse files containing in a connected flash drive and select file for streaming. Module supports streaming only from FAT32 formatted flash drives. Other file systems (FAT16, NTFS, exfat, EXT4) are not supported. For the best performance please format the flash drive with allocation unit size of 16 kilobytes. In a "File" edit box selected file name and path is displayed. You can manually edit them or select from " flash content" tree. The button below is used for streaming start and stop of selected file. In a " flash content" panel a three of flash directories and files shown. Directories are marked by icon. Double click on directory name to open its contents. Files with TS extention are marked by icon and can be selected for streaming by mouse click. The selected file and path is shown in "File" edit box. Note: only files of MPEG2 transport stream are supported. status parameters are displayed in the box at right: reading bitrate in Mbps; current and total time of file in hours:minutes:seconds format; number of wraps of file play. Figure 15. Input channel selection Output streams table This table (Figure 16) is used to individually configure the output streams. After scanning of services from selected input, a "Count of output streams" is set to maximum available streams. This value can be changed manually. Figure 16. Output streams table 9