GUY-GRIP Dead-end NOMENCLATURE GENERAL INFORMATION SAFETY CONSIDERATIONS (440)
|
|
- Raymond Todd
- 6 years ago
- Views:
Transcription
1 GUY-GRIP Dead-end NOMENCLATURE Identification Tape Color Code and Cross-Over Marks* (A) (B) Short Leg Pitch Cabled Loop Cross-over Marks*: (A) Indicate starting point for application on smaller diameter fittings described on the reverse side of this page. (B) Indicates alternate starting point for application on larger diameter fittings described on the reverse side of this page. Cabled Loop: Furnished as standard, all sizes. Long Leg Pitch : One complete wrap. Color Code and : Assist in identification of strand size, corresponding to tabular information appearing on catalog pages. Identification Tape: Shows catalog number, nominal sizes. Short Leg-Long Leg: Identifies rods belonging to each leg, after application. During application, the short leg should be applied first. GENERAL INFORMATION GUY-GRIP Dead-ends are intended for use on single wood poles associated with distribution construction. GUY-GRIP Dead-ends were not designed or tested for use on overhead shield wires and not intended for that application. Refer to Big-Grip Dead-end, an alternate product recommended for guying transmission construction, or tower and antenna applications. Refer to the Installation Tools section for the PLP Pulling Eye, designed to assist application at the anchor. RATED HOLDING STRENGTH: GUY-GRIP Dead-ends are rated at 100% of the strand s published rated breaking strength. MATERIAL SELECTION: GUY-GRIP Dead-ends are made of the same basic material as the strand to which they are applied. This pertains to galvanized, *Bezinal, **Copperweld, Aluminum clad steel, stainless Type 302, and stainless Type 316. Any of these materials can be selected from the catalog tables. The recommended types of strand are also indicated. TAPPING: GUY-GRIP Dead-ends are mechanical devices not designed as current transfer connectors. Consequently, tapping is not recommended over or through the GUY-GRIP Dead-end. APPLICATION-INSPECTION: Within the first 3 months after initial application, GUY-GRIP Dead-ends may be removed and reapplied two times after initial application for the purpose of retensioning the guy. After 3 months a new Dead-end should be used any time removal is required. GUY-GRIP Dead-ends should be used on hardware that is held in a fixed position; the fitting should not be allowed to rotate or spin about the axis of the strand. They should not be used as tools; that is, come-alongs, pulling-in grips, etc. Lay direction of both the GUY-GRIP Dead-ends and the strand should be the same. Most strand is left-hand lay. STRAND TAIL: For appearance and safety the strand tail should be cut as close as convenient to the crossover mark and buried inside the crossover mark if possible. If desired, the strand tail can, instead, extend through the loop for grounding purposes. Any tail over 2" or 3" should be restrained and not permitted to rotate during loading of the guy. SAFETY CONSIDERATIONS This product is intended for a single (one-time, permanent) use and for the specified application, although it may be reapplied twice for retensioning within 90 days of initial installation. CAUTION: DO NOT MODIFY OR REUSE THIS PRODUCT AFTER 90 DAYS UNDER ANY CIRCUMSTANCES. 2. This product SHOULD NOT be used as a tool; that is, as a come-along, pulling in grips, temporary bracing, etc. 3. This product is intended for use by trained crafts people only. This product SHOULD NOT BE USED by anyone who is not familiar with and trained in the use of it. 4. When working in the area of energized lines with this product, EXTRA CARE should be taken to prevent accidental electrical contact. 5. For PROPER PERFORMANCE AND PERSONAL SAFETY be sure to select the proper size GUY-GRIP Dead-end before application. 6. GUY-GRIP Dead-ends are precision devices. To insure proper performance, they should be stored in cartons under cover and handled carefully. *Bezinal is a registered trademark of the Bekaert Corporation. **Copperweld is a registered trademark of the Copperweld Co.
2 GUY-GRIP Dead-end HARDWARE CONSIDERATIONS CABLED LOOP: Anchor eyes and other fittings need groove diameters only slightly larger than the strand because the diameter of the cabled rods of GUY-GRIP Dead-ends approximates strand diameter. Cabled loops are designed for a variety of fittings with dimensions shown in the table below. Distribution (Overhead): Section 20 GUY-GRIP Dead-end Suggested hardware dimensions for cabled-loop GUY-GRIP Dead-ends Dead-end Range Nominal Sizes Seat Dimensions (Figures 1 & 2) Minimum Groove (in.) (fig. 2) Minimum Hole * (in.) (fig. 3) Min. Max. Galvanized Steel Aluminumclad Steel Min. seat dia. at first cross-over mark Max. seat dia. at first cross-over mark Max. seat dia. at second cross-over mark /8 3/4 1-3/4 3/16 1/ /32 3/4 1-3/4 2-1/2 1/4 5/ / /4 2-1/2 1/4 3/ /32 3 #10, 4M3 1-1/8 1-3/4 2-1/2 5/16 3/ /4 7 #12, 6M 1-1/8 1-3/4 2-1/2 5/16 7/ /32 7 #11, 8M 1-1/8 1-3/4 2-1/2 3/8 1/ /16 7 #10, 10M 1-1/4 1-3/4 2-1/2 3/8 9/ /8 7 #8, 14M, 16M 1-3/8 1-3/4 2-1/2 7/16 5/ /16 7 #7, 18M, 20M 1-3/8 2-3/8 1/2 11/ ** 7 #6 1-3/8 2-3/8 9/16 3/ ** 7 #5, 25M 1-1/2 2-5/8 5/8 15/16 * Depending on geometric shape of the hole, a hole diameter less than specified may be acceptable. ** Use Big-Grip Dead-ends. Guying of transmission structures and metal towers require Big-Grip Dead-ends, VARI-GRIP Dead-ends. Anchor Rods Acceptable Fittings Thimble Eye-Bolts, -Eyenuts & Eyes Pole Fittings Guy-Strain Insulators ANSI CAUTION: Hardware of this type is not normally acceptable because fatigue life of GUY-GRIP Dead-ends could be substantially reduced. Heavy-Duty-Type Cable Thimbles, if used, can collapse when guy tensions are high. If thimbles are used in the loop of the GUY-GRIP Dead-end, a large pin is recommended to fill the loop of the thimble to prevent distortion. The collapsing strength of the thimble and the proper pin size should be obtained from the thimble manufacturer. 20-3
3 GUY-GRIP Dead-end: Galvanized Steel Extra High Strength, High Strength, Siemens Martin, Utilities Grade 3 B-Coat Size Construction Wt./Lbs. Color Code GDE / Red GDE / Green GDE / Yellow GDE / Blue GDE /16 GDE / Black Orange GDE / Green C-Coat Size Construction Wt./Lbs. Color Code GDE / Red GDE / Green GDE / Yellow GDE / Blue GDE /16 GDE / Black Orange GDE / Green Left-hand lay standard (3) Rated holding strength is 100% of published rating for all grades of galvanized strand. (4) Consult PLP for sizes and stranding not shown. 20-4
4 GUY-GRIP Dead-end: Bezinal Bezinal 2 Size BDE /16 BDE /4 BDE /16 BDE /8 Construction Weight (Lbs) Distribution (Overhead): Section 20 Color Code Red Yellow Black Orange BDE / Green GUY-GRIP Dead-end Left-hand lay standard (1) Big-Grip Dead-end is recommended as an alternative product for guying multiple pole structures or metal towers associated (2) Rating holding strength is 100% of the published rating for the strand. (3) Dead-ends are manufactured from Bezinal Material or common 95% ZN-5% AL-Mischmetal Alloy produced to ASTM-B750. Bezinal is a registered trademark of the Bekaert Company. 20-5
5 GUY-GRIP Dead-end Aluminum Clad Steel 3 Nominal Size Wt./lbs. Color Code AWDE # Orange AWDE-4108 AWDE-4110 AWDE-4113 AWDE M 3 # 10 3 # 9 6M 3 # 8 8M 3 # 7 10M 5/16" - 7 # Green Yellow Blue Black AWDE M Green AWDE # M 11/32" - 7 # Yellow AWDE M Blue AWDE # 5 3/8" - 7 # 8 16M Orange AWDE M Black AWDE /16" - 7 # Green AWDE M Yellow AWDE /2" - 7 # Blue AWDE M Red AWDE # Yellow Left-Hand Lay standard (3) Rated holding strength is 100% of all grades of aluminum clad steel strand. (4) Rated holding stength is 100% of the published rating for the strand. (5) Consult PLP for sizes and stranding not shown. 20-6
6 GUY-GRIP Dead-end: Aluminized Aluminized 4 Distribution (Overhead): Section 20 GUY-GRIP Dead-end Size Construction Wt./lbs. Color Code AZDE / Red AZDE / Yellow AZDE / Blue AZDE /16 AZDE / Black Orange AZDE / Green Left-Hand Lay standard (3) Refer to General Information for material selection. (4) Rated holding strength is 100% of all grades of aluminized strand. (5) Consult PLP for sizes and stranding not shown. 20-7
7 GUY-GRIP Dead-end: Copperweld Copperweld 4 Nominal Size Wt./lbs Color Code CDE M Orange CDE # Red CDE M White CDE # Green CDE # 9 6M Yellow CDE M White CDE M 3 # Blue CDE-3109 CDE M 7 # 10-5/16" 3 # 7 7 # 9-11/32" 12.5M 3 # Red Green CDE M Blue CDE # 8-3/8" 16M 3 # White CDE M Orange CDE M 7 # 7-7/16" Yellow CDE # 6-1/2" Blue CDE M Green CDE # 5-9/16" Yellow Left-Hand Lay standard (3) Refer to General Information for material selection. (4) Rated holding strength is 100% of the published rating of the strand. (5) Consult PLP for sizes and stranding not shown. (6) Copperweld is a registered trademark of the Copperweld Co. 20-8
8 GUY-GRIP Dead-end: Stainless Steel Type 302 and Type 430 Distribution (Overhead): Section 20 GUY-GRIP Dead-end Type 302 Wt./ Lbs. Percent of s Rated Breaking Strength Size Construction Per Carton Color Code SDE / Blue 100% SDE / Yellow 100% SDE / Black 90% SDE /16 SDE / Orange 93% Green 83% Type 316 Type 316 Wt./ Lbs. Percent of s Rated Breaking Strength Size Construction Per Carton Color Code SDE / Blue 100% SDE / Yellow 100% SDE / Black 90% SDE-6504* 5/16 SDE / Orange 93% Green 87% SDE / Blue 85% *These Dead-ends utilize the open helix design. Left-Hand Lay standard (3) Refer to General Information for material selection. (4) Consult PLP for sizes and stranding not shown. 20-9
Lashing Rods NOMENCLATURE GENERAL RECOMMENDATIONS. C = D x m = D x.666. m = D x.414. m = D x.483. C = (D + m) x.850. Length.
Lashing s NOMENCLATURE Deburred and : Assist in identification of size, corresponding to tabular information appearing on price pages. diameter: Identifies size of metal wire, corresponding to tabular
More informationSection 8 FIBERLIGN Hardware for Aerial FTTP Applications
Section FIBERLIGN Hardware for Aerial FTTP Applications Table of Contents Page FIBERLIGN Products for ADSS Applications FIBERLIGN ADSS Drop Cable Dead-end...-2 FIBERLIGN Midspan Drop...-5 FIBERLIGN LITE
More informationSection 20 Dead-end & Accessories
PREVIOUS SEARCH NEXT Dead-end & Accessories: Section 20 Section 20 Dead-end & Accessories Table of Contents Page Figure-8 Messenger Dead-end...20-2 GUY-GRIP Dead-end...20-3 GUY-LOCK...20-6 Big-Grip Dead-end...20-7
More informationPortable Outlet Boxes
INDEX Introduction... 456 Single Gang... 458 Two Gang... 459 For technical support call 800-824-3005 Online catalog available at leviton.com 455 Portable Outlet Boxes Leviton s line of temporary power
More informationAll Dielectric Self Supporting (ADSS) Fiber Optic Cable Installation
All Dielectric Self Supporting (ADSS) Fiber Optic Cable Installation Underground Installation M P - 1012 Issue #3 March 2011 DISCLAIMER OF WARRANTIES AND LIMITATION OF LIABILITIES The practices contained
More informationFor Sales & Information, Call Toll Free: (888)
PCR Outline Dimensions 2.75" (69.8 mm) 0.44" (11 mm) 0.25" (6.3 mm) (-) (+) 15.8" (401 mm) 9.3" (236 mm) Nameplate 1.25" (31.8 mm) 3.0" (76 mm) 7.40" (188 mm) 12.63" (321 mm) R 0.219" (R 5.56 mm) Serial
More informationA449-6S 70 CENTIMETER FM YAGI ANTENNA MHz
ASSEMBLY AND INSTALLATION A449-6S 70 CENTIMETER FM YAGI ANTENNA 440-450 MHz COMMUNICATIONS ANTENNAS 951425 (7/93) WARNING THIS ANTENNA IS AN ELECTRICAL CONDUCTOR. CONTACT WITH POWER LINES CAN RESULT IN
More informationIndyGo Facility Upgrades Project 35671EE
SECTION 260553 IDENTIFICATION FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Identification for raceways. 2. Identification of power and control cables. 3. Identification for
More informationInstructions. Cable with Armor F CAUTION. October Rev A
3M Single Conductor Accessory Breakout Kits (BOK's) for use with 3M Cable Accessories (Terminations, T-Bodies and Push-On Elbows) For Use With Single Conductor Accessories On Three-Core Conductor Cables
More informationA CENTIMETER FM YAGI ANTENNA MHz
ASSEMBLY AND INSTALLATION A449-70 CENTIMETER FM YAGI ANTENNA 440-450 MHz COMMUNICATIONS ANTENNAS 951424 (10/91) WARNING THIS ANTENNA IS AN ELECTRICAL CONDUCTOR. CONTACT WITH POWER LINES CAN RESULT IN DEATH
More informationSpecification for Loose Tube Fiber Optic Cable (Non-Metallic, Dry Block, Figure-8) (G.652.D)
2-3, Marunouchi 2-chome, Chiyoda-ku, Tokyo 100-8322, Japan No. FB-KL4001C for Loose Tube Fiber Optic Cable (Non-Metallic, Dry Block, Figure-8) (G.652.D) Aug 2014 1 1. General This specification describes
More informationchoice of types to suit many applications, from simple containers, toolboxes, industrial canister type vacuum cleaner, insulation
Solutions Inc. TL-7800 Line The DFCI TL-7800 Line of Toggle Latches offers the designer a wide choice of types to suit many applications, from simple containers, toolboxes, industrial canister type vacuum
More informationNational Wire and Cable and National Cable Molding Headquarters Los Angeles California
National Wire and Cable and National Cable Molding Headquarters Los Angeles California CAPABILITIES Medical Business Machines Communications Equipment Computer Equipment Audio Systems General Instrumentation
More informationCOYOTE CLOSURE FOR UNDERGROUND, AERIAL, AND BURIED SPLICES 6.0" x 22" 8.5" x 22" (15.24 cm x cm cm x cm)
OCTOBER 2004 COYOTE CLOSURE FOR UNDERGROUND, AERIAL, AND BURIED SPLICES 6.0" x 22" 8.5" x 22" (15.24 cm x 55.88 cm 21.59 cm x 55.88 cm) Be sure to read and completely understand this procedure before applying
More informationOPTICAL FIBER CABLE, ALL DIELECTRIC SELF SUPPORTING CABLE
SPEC NO. TEC-OPTIC-81101A(Rev.4)-2014.07 TECHNICAL PROPOSAL FOR OPTICAL FIBER CABLE, ALL DIELECTRIC SELF SUPPORTING CABLE ( Span length : Max. 100m ) APPROVED BY : J.Y. LEE / HEAD OF TEAM ENGINEERING TEAM
More informationACADEMIC SUCCESS CENTER THE COLLEGE AT BROCKPORT STATE UNIVERSITY OF NEW YORK PROJECT NO
SECTION 270536 - CABLE TRAYS FOR COMMUNICATIONS SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationDLP ANTENNA INSTRUCTION MANUAL. Dielectric LLC 22 Tower Road Raymond, Maine Phone:
DLP ANTENNA INSTRUCTION MANUAL Dielectric LLC 22 Tower Road Raymond, Maine 04071 Phone: 800-341-9678 TABLE OF CONTENTS Section Title Page Warnings 1 Return Policy. 1 Factory Tests... 1 Antenna Description....
More informationChannel Cable Tray - Accessories
Splice Plate The Splice Plate has the standard 4-hole pattern for all cable channel. Provided with straight sections and fittings. 9(*)-1043 3 (76) 9(*)-1044 4 (101) 9(*)-1044-6 6 (152) Horizontal Adjustable
More informationMediacom Upgrade/Splicing Procedures (based on original document from Corporate dated 4/16/98)
Mediacom Upgrade/Splicing Procedures (based on original document from Corporate dated 4/16/98) 1. Splicing specifications are provided by Mediacom, but due to resplice conditions, many locations become
More informationASSEMBLY AND INSTALLATION 3 ELEMENT 6 METER BEAM
ASSEMBLY AND INSTALLATION A50-3S 3 ELEMENT 6 METER BM COMMUNICATIONS ANTENNAS 951364 (12/94) WARNING THIS ANTENNA IS AN ELTRICAL CONDUCTOR. CONTACT WITH POWER LINES CAN RESULT IN DTH, OR SERIOUS INJURY.
More informationAerial Cable Installation Best Practices
Aerial Cable Installation Best Practices Panduit Corp. 2007 BEST PRACTICES Table of Contents 1.0 General... 3 2.0 Introduction... 3 3.0 Precautions... 4 4.0 Pre-survey... 5 5.0 Materials and Equipment...
More informationMulti-Media Installation Guide
Multi-Media Installation Guide Coaxial Page 2 Data Plug Page 7 Data Jack Page 10 Telephone Page 13 Splicing Page 15 Cable Types Cable Types Two basic types of cable are used in multimedia installations.
More informationPULL SUPPORT PROTECT CONNECT
PULL SUPPORT PROTECT CONNECT CABLE GRIPS, PROTECTORS, CONNECTORS AND ACCESSORIES 2012 A business focused on your needs From the day our family business was founded, we ve dedicated ourselves to designing,
More informationCaution. Hanging the Screen:
Installation Instructions for Laminar and Laminar XL Projection Screens Caution 1. Read Instructions through completely before proceeding; keep them for future reference. Follow these instructions carefully.
More informationFlexible Cord. Inside this section
2 Strain Relief Cord Connectors provide a liquid tight and strain relief termination for flexible type neoprene, vinyl, or PVC control cord and cable, and are now offered in steel, aluminum, and nylon.
More informationOCC Installation Round Messenger Guidelines Excerpt from Optical Cable Corporation s INSTALLATION GUIDE
Installation Round Messenger Guidelines Excerpt from Optical Cable Corporation s INSTALLATION GUIDE Round Messenger (ADSS) A round messenger fiber optic cable is designed for use in aerial installations
More informationSECTION MEDIUM VOLTAGE CABLE INSTALLATION. 1. Section Underground Ducts and Manholes.
SECTION 33 71 49.23 MEDIUM VOLTAGE CABLE INSTALLATION PART 1 GENERAL 1.1 SCOPE A. Work included in this Section: Medium Voltage Cable (4 kv and 12 kv) Installation and Termination. Removal and return of
More information1.0 DESCRIPTION. This specification covers roll-up signs to be used in temporary traffic control zones.
(Page 1 of 10) ROLL-UP SIGNS (MGS-04-01O) 1.0 DESCRIPTION. This specification covers roll-up signs to be used in temporary traffic control zones. 2.0 MATERIAL. 2.1 SIGNS AND OVERLAYS. 2.1.1 SUBSTRATES.
More informationCONSTRUCTION SPECIFICATION FOR TRAFFIC SIGNAL EQUIPMENT
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.PROV 620 APRIL 2017 CONSTRUCTION SPECIFICATION FOR TRAFFIC SIGNAL EQUIPMENT TABLE OF CONTENTS 620.01 SCOPE 620.02 REFERENCES 620.03 DEFINITIONS 620.04
More information3M Cold Shrink QS-III Silicone Rubber Splice Kit 5488A-TOW/WOT
3M Cold Shrink QS-III Silicone Rubber Splice Kit 5488A-TOW/WOT For Tape Over Wire (TOW) and Wire-Over-Tape (WOT) Shielded Cable For 250 2000 kcmil cable with 650-mil primary insulation thickness Instructions
More informationAll Dielectric Self Supporting (ADSS) Fiber Optic Cable Installation
All Dielectric Self Supporting (ADSS) Fiber Optic Cable Installation Underground Installation Install 22 June 23, 2017 DISCLAIMER OF WARRANTIES AND LIMITATION OF LIABILITIES The practices contained herein
More information92656 XR RTQ RG-6 F Comp Connector 100JR
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 92656 XR RTQ F Comp Connector 100JR Ideal Catalog Number 92656 Manufacturer Ideal Compression Connector, Type F Connection,
More informationWinch Adjustable Feed Level Tubes for the Adult Turkey Feeder Installation & Operator s Instruction Manual MF /99
Winch Adjustable Feed Level Tubes for the Adult Turkey Feeder Installation & Operator s Instruction Manual MF7-8 6/99 June 999 MF7B Chore-Time Warranty Winch Adjustable Feed Level Tubes for ATF Chore-Time
More informationCHAPTER 14 WIRING SIGNALS AND LIGHTING FIELD GUIDE Wiring Requirements WIRING
WIRING CHAPTER 14 WIRING The installation of all wiring, including electrical cables and conductors, must conform to the National Electrical Code (NEC). The Code represents the minimum required standard.
More informationENGINEERING COMMITTEE Interface Practices Subcommittee. ANSI/SCTE (Formerly IPS SP 001)
ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE 74 2003 (Formerly IPS SP 001) Specification for Braided 75 Ω Flexible RF Coaxial Drop Cable NOTICE The Society
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 26 0553 - IDENTIFICATION FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationStudent Services & Classroom Addition
SECTION 260513 - MEDIUM-VOLTAGE CABLES PART 1 - GENERAL 1.1 SUMMARY A. Section includes cables and related cable splices, terminations, and accessories for mediumvoltage (2001 to 35,000 V) electrical distribution
More informationTriax TechInfo. Installing and pulling Fibre Optic cables
Installation methods for both wire cables and Fibre Optical cables are similar. Fibre cable can be pulled with much greater force than copper wire if you pull it correctly. Just remember these rules: 1)
More informationHCS - HES Cabling Systems
HCS - HES Cabling Systems Installation Manual for HCS High-Capacity Fiber-Optic Rack-Mount Cabinets Be sure to read and completely understand this procedure before applying product. Be sure to select the
More informationPT9150. Heavy Industrial Incremental Encoder
PT950 Heavy Industrial Incremental Encoder Linear Position to 550 inches (00 cm) luminum or Stainless Steel Enclosure Options VLS Option To Prevent Free-Release Damage IP67 NEM 6 Protection GENERL Full
More information3M Better Buried Closures
3M Better Buried Closures Instructions March 2016 78-0015-2945-8-A Contents: 1.0 General... 3 2.0 Kit Contents... 3 3.0 Closure Selection Guide... 4 4.0 LHS End Cap Installation... 5 5.0 Cable Preparations...
More informationInstalling a Wire Mesh Pulling Grip on All-Dielectric DX Armored Fiber Optic Cables
revision history Issue Date Reason for Change Related literature SRP-004-136 Accessing All-Dielectric DX Armored Fiber Optic Cables Admonishments 1. General This procedure provides instructions for installing
More informationUNOLS Wire Pool Database. Presented by Rick Trask Woods Hole Oceanographic Institution
UNOLS Wire Pool Database Presented by Rick Trask Woods Hole Oceanographic Institution Database Development: A Collaborative Effort Rick Trask, Wire Pool Manager Ruthanne Molyneaux, Administrative Support
More informationPurchase Now ANSI/ICEA S
STANDARD FOR OPTICAL FIBER OUTSIDE PLANT COMMUNICATIONS CABLE Publication S-87-640 Fourth Edition September 2006 Published By Insulated Cable Engineers Association, Inc. (ICEA) P.O. Box 1568 Carrollton,
More informationCASS TL-3 (Utilizing C-Shaped Post) Maintenance and Repair Manual
CASS TL-3 (Utilizing C-Shaped Post) Maintenance and Repair Manual Part No. 620290B Revision March 2007 INDEX Page Introduction 3 General CASS TM Maintenance 3 Pre-stretched Cable 3 Non Pre-stretched Cable
More informationSmart Products. Ingenious Solutions.
THE FUTURE IS ON Smart Products. Ingenious Solutions. Wiring Devices, Energy anagement Solutions and Commercial Data Infrastructure Products L-200 INDEX Introduction... 754 Pulling Grips... 761 Fiber Optic
More informationULTIMATE SNAP-N-SEAL
ULTIMATE SNAP-N-SEAL F Series Compression Connectors Thomas & Betts introduces the Ultimate Snap-N-Seal Compression Connector, the newest addition to the Snap-N-Seal system. Look for the classic design
More informationMiniXtend Cable with Binderless* FastAccess Technology Jacket and Buffer Tube Removal Procedures. 1. General. 2. Precautions
MiniXtend Cable with Binderless* FastAccess Technology Jacket and Buffer Tube Removal Procedures 004-273-AEN, Issue 2 Table of Contents 1. General.... 1 2. Precautions.... 1 2.1 Cable Handling Precautions...
More informationE6CP-A. An Absolute Encoder at About the Same Price as an Incremental Encoder. Ideal for robot limit signals. Low-cost Encoder with Diameter of 50 mm
Low-cost Encoder with Diameter of 50 mm CSM DS_E An Absolute Encoder at About the Same Price as an Incremental Encoder. Ideal for robot limit signals. High-precision detection of automatic machine timing.
More informationTECHNICAL SPECIFICATION
ISSUED : OCT. 02, 2006 PAGE : 1 OF 9 REV. : 1 TECHNICAL SPECIFICATION FOR GST 2006-043A LOOSE TUBE DRY CORE CABLE SINGLE JACKET/SINGLE ARMOR (SJSA CABLE) Prepared By : Oh-Heoung Kwon Engineer Optical Technical
More informationNumber of Fiber 6 Core 12 Core. Part Number
Order Information OUTDOOR OFC-Drop Wire, MM (OM2) (50/125) LOOSE TUBE BLACK Number of Fiber 6 Core 12 Core Part Number 74550006 74550012 1. General 1. Scope 2. Quality Assurance This specification covers
More informationCable Retainers UTILITY PRODUCTS. Cable Retainer Assy, For 4 Foundation Anchor, Galvanized Steel SP-6224-GLV
Cable Retainers Cable Retainer Assy, For 4 Foundation Anchor, Galvanized Steel SP-6224-GLV Pelco s anti-theft Cable Retainer is the best solution to help prevent copper cable theft in street light poles.
More informationPT9420 Cable Actuated Sensor Industrial ma 0..20mA
PT9 Cable ctuated Sensor Industrial.. m 0..m bsolute Linear Position to 550 inches ( meters) luminum or Stainless Steel Enclosure Options VLS Option to Prevent Free-Release Damage IP68 / NEM 6 Hazardous
More informationSPECIAL SPECIFICATION 8540 Telecommunication Cable
2004 Specifications CSJ 0914-00-307 & CSJ 0914-25-003 SPECIAL SPECIFICATION 8540 Telecommunication Cable 1. Description. This specification governs the materials, installation, termination, splicing, testing,
More informationOCC Installation Figure 8 Guidelines Excerpt from Optical Cable Corporation s INSTALLATION GUIDE
Installation Figure 8 Guidelines Excerpt from Optical Corporation s INSTALLATION GUIDE Figure 8 A figure 8 fiber optic cable design incorporates a steel or dielectric messenger into the fiber optic cable
More informationFIST-GCOG2-Dx6. Follow all local safety regulations related to optical fiber plant elements.
FIST-GCOG2 I N S T A L L A T I O N I N S T R U C T I O N TC-986-IP Rev A, Mar 2017 www.commscope.com FIST-GCOG2-Dx6 Content 1 Introduction 2 General 2.1 Abbreviations 2.2 Kit contents 2.3 Tools 2.4 Accessories
More informationCable Ranges Unit Std WT/ Cat. # Color Size Min. Max Ctn Pkg 100
Straight Industrial specification grade, screw machined steel, zinc plated Provides a UL liquid tight and strain relief termination for flexible, neoprene, vinyl, or PVC control cord and cable Color Coded
More informationSafety Codes Council Conference Banff C Panel Discussion
Safety Codes Council Conference Banff 2014 90 C Panel Discussion Tim Driscoll OBIEC Consulting Ltd. George Morlidge Fluor Canada Ltd. Scott Basinger Eaton Canada René Leduc Marex Canada Limited Perspectives
More informationConnectAnywhere Prep Kit OEM INSTALLATION MANUAL
Connectnywhere Prep Kit OEM INSTLLTION MNUL TBLE OF CONTENTS Introduction 2 Safety 2 Resources Required 3 Preparation 3 Installation 3 Notes 9 Introduction This document provides instructions for the installation
More information3 SLiC Aerial Closure with Rubber End Seal
3 Aerial Closure with Rubber End Seal Instructions 1.0 General 1.1 This instruction bulletin describes the assembly of the 3M Aerial Closure with external bonding hanger brackets. These closures are suitable
More informationcable, conductor, WIre, hose and FIBre InstallatIon and support MAde easier, SAfer And More dependable installation ProdUcTS TrUSTed innovation
installation ProdUcTS cable, conductor, WIre, hose and FIBre InstallatIon and support MAde easier, SAfer And More dependable www..com TrUSTed innovation From Innovative design, prototyping and product
More informationSLiC Fiber Aerial Closure System
3 SLiC Fiber Aerial Closure System SLFC 533-SP SLFC 533-TS SLFC 733-SP Instructions May 2005 78-8135-4502-3-B N C H E S R A N G E M IL L IM E T E R S.4 10.6.8 A B C 15 20 I 1.0 Kit Contents Note: Examine
More informationWCH Slack Storage Housing (WCH-SSH-2 & WCH-SSH-4-12)
Corning Cable Systems SRP-003-448 Issue 3, October 2000 Page 1 of 6 WCH Slack Storage Housing (WCH-SSH-2 & WCH-SSH-4-12) Figure 1 Table of Contents 1. General... 1 2. Description... 1 3. Tools and Materials...
More informationFOSC 450 C6 and D6 Closures
FOSC 450 C6 and D6 Closures I N S T A L L A T I O N I N S T R U C T I O N Fiber Optic Splice Closure 1. General Product Information The FOSC 450 C6 and D6 fiber optic splice closures use compressed gel
More information3M Motor Lead Inline Splice 5331, 5332, 5333 & 5334
3M Motor Lead Inline Splice 5331, 5332, 5333 & 5334 for 5/8 kv Non-Shielded and Shielded Cables (Ribbon, Wire and UniShield Cables) Instructions Cable Size Range: Feeder: #8 AWG 500 kcmil Motor Lead: #10
More information3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN
3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN-500-1000 for Jacketed Concentric Neutral (JCN) and Flat Strap Neutral Cable Instructions IEEE Std. 404 15 kv Class 150 kv BIL F CAUTION Working around
More informationINTRODUCTION INSTALLATION LIGHTNING RETARDING LOOPS. Figure 1. Relay Box Antenna Connections. Relay Box Cable Connections
INTRODUCTION The Ameritron RCS-8V is a remote controlled coaxial RF switch that will operate with negligible loss, radiation and VSWR at all frequencies up to 250 MHz. Only a slight compromise in VSWR
More informationSUMITOMO PRODUCT SPECIFICATION. FutureFLEX. TCxxMSOS-2 HIGH PERFORMANCE OSP TUBE CABLE SERIES WITH GALVANIZED STEEL INTERLOCKED ARMORING
SUMITOMO PRODUCT SPECIFICATION FutureFLEX TCxxMSOS-2 HIGH PERFORMANCE OSP TUBE CABLE SERIES WITH GALVANIZED STEEL INTERLOCKED ARMORING SUMITOMO ELECTRIC LIGHTWAVE CORP. 201 South Rogers Lane, Suite 100,
More informationIdentification - electrical services
Identification - electrical services Aesthetic All live phase cable sheathing to be brown coloured and neutral phase cable sheathing to be blue coloured, all labelled L1, L2, L3 & N respectively in accordance
More informationDIN Connectors DIN06 E-03
DIN Connectors DIN0 E-0 Contents Introduction HOSIDEN DIN connectors are supplied to electronic equipment manufacturers both in Japan and overseas and are very well accepted because of high quality, a
More informationInstallation Manual IPT Installation of skillet systems with 125 A track current. MV a-E.
www.wampfler.com Page 1 of 27 Index Page 1 Basics...4 2 Basic understanding of an IPT -system...5 3 General rules regarding metal parts in close proximity...6 3.1 Envelope free of ferromagnetic material...6
More informationMicro duct Cable with HDPE Sheath for Installation by Blowing
Optical Fiber Cable Technology Specification INTERNAL Optical Fiber Cable Specification Micro duct Cable with HDPE Sheath for Installation by Blowing GCYFY-12/24/36/48/72/96/144/288/432/576B1.3 V7.0 2018-3-20,CCopyright.
More informationMagnetic Sensor - Incremental EHP
small design: 12 x 13 x 35 mm stainless steel case resolution up to 0,5 μm; hysteresis ± 1μm pole pitch:1; 2 mm output signal: Digital (TTL-RS422) or analog (1 Vpp) direct connection to control / display
More informationCon o t n e t n e t n s t
Contents Page Item 3 Safety Warnings 4 Glossary 5 Attachment and Removal of Caster Frames 6 Line Array Element Attachment 7 Angle Selection 8 Rigging Frame (Bumper) 9 Electrical connection 10 System Mounting
More informationAPPLIANCES /// MTA, CST-100 II AND SL-156 CONNECTORS. CONNECTORS/ APPLIANCES MTA, CST-100 II and SL-156 Connectors
PPLINCES /// MT, CST-100 II ND SL-156 CONNECTORS CONNECTORS/ PPLINCES MT, CST-100 II and SL-156 Connectors Contents Introduction This catalog has been designed to assist you, our customer, identify products
More information2178 Fiber Optic Splice Case and 2181 Cable Addition Kit
2178 Fiber Optic Splice Case and 2181 Cable Addition Kit Instructions January 1994 Issue 1, 34-7029-6387-6 1 2 Contents: 1.0 General... 4 2.0 Specifications... 4 3.0 Kit Contents... 5 SECTION 1: 2178 Splice
More informationAdapter Selection. Entry Size (Continued) Table E. Multiplication. factors for wire bundles. with Equal Size Wires. This table provides multiplication
Table E. Multiplication Factors for Wire Bundles with Equal Size Wires This table provides multiplication factors for wire bundles of to 6 wires. To determine the approximate diameter of a wire bundle
More informationUp to 85% higher Service Life due to efficient sealing method.
Robot Accessories Feeding through Up to 85% higher Service Life due to efficient sealing method. 346 Robot Accessories Feeding through Feeding through DDF 2 Rotary Feed-through Series Size Page DDF 2 348
More informationAccessories (Order Separately)
CSM_PhotoMicro_OP_E_8_ Accessories (Order Separately) Ordering Information s and Hold-down Clips Sensor models EE-SX7@ (A, P, R), EE-SX7@, EE-SY7@, EE-SPY@/@, EE-SPX0N/0N, EE-SPW/ Type Cable length Model
More informationSPECIAL SPECIFICATION 6559 Telecommunication Cable
2004 Specifications CSJ 0015-09-147, etc. SPECIAL SPECIFICATION 6559 Telecommunication Cable 1. Description. This specification governs the materials, installation, termination, splicing, testing, training,
More informationS Regulators. Supplement 1. Contents. Control Replacement Assembly Installation Instructions Supplement
Regulators Control Replacement Assembly Installation Instructions Supplement Service Information S225-40-1 Supplement 1 Figure 1. CL-6A Control Replacement Assembly. Contents Safety Information... 2 Product
More informationLimited Tension Formed Wire Dead End for ADSS Cable
Limited Tension Formed Wire Dead End for ADSS Cable 4 3 5 ALL DIELECTRIC SELF SUPPORTING CABLE 2 LENGTH "L" 1 Item Description Material 1 Reinforcing Rods (SRR) Galvanized Steel 2 Formed Wire Dead-End
More informationFREEDM Loose Tube Interlocking Armored Cables
features and benefits Flexible, interlocking armor design Gel-free waterblocking technology Color-coded tubes and fibers UV-resistant, flameretardant jacket UV-Resistant Flame-Retardant Outer Jacket InterlockingArmor
More informationSingle Point Flow Monitor SW118 SW119
SW8 SW9 SW8 SW9 Single point flow monitors with MIN/MAX monitoring function, suitable for water, oil, air and media with similar thermal conductivities (selectable by means of a medium switch). With either
More informationSPECIFICATION FIBER OPTIC SPLICE CLOSURE. Spec No : VSS-1007-BS403A-04A/SD. VSS-0107-BS403A-04A/SD R & D Center Manufacturing Division
SPECIFICATION FIBER OPTIC SPLICE CLOSURE Model Spec. No. Distribution Depts. VSOF-BS403A VSS-0107-BS403A-04A/SD R & D Center Manufacturing Division Sales Division Management Division Revision 10. 07 (Rev.4)
More informationCable Retention Force Testing of Trunk & Distribution Connectors
ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE 102 2016 Cable Retention Force Testing of Trunk & Distribution Connectors NOTICE The Society of Cable Telecommunications
More informationFiberglass - Technical Data
- Technical Data Cable Tray Thermal Contraction and Expansion X : Denotes hold-down clamp (anchor) at support. _ : Denotes expansion guide clamp at support. It is important that thermal contraction and
More informationEXPlora. Introduction
Introduction EXPlora The EXPlora range is most suited to manufacturers of ancillary electrical equipment such as motors, pumps, lighting equipment, process and control gear for use in factories and plant
More informationType SCH94FO. Type SCH94FO. Description
Type SCH94FO Hollow Shaft Fiber Optic Encoder - Ø 94 mm Dual Output Option (Digital & Fiber Optic) Fiber Optic Transmission up to 2,000 meters (~ 1.25 miles) No Degradation of Encoder Signal from Electrical
More informationDownloaded from
EEEEI 23 FEB 1990 MILITARY SPECIFICATION CABLE, POWER, ELECTRICAL AND CABLE SPECIAL F URPOSE, ELECTRICAL SHIELDED AND UNSHIELDED, GENERAL SPECIFICATION FOR This amendment forms a part, of MIL-C-27SOOG,
More information3M Cold Shrink QS4 Integrated Splice Kit QS4-35TS
3M Cold Shrink QS4 Integrated Splice Kit QS4-35TS-350-1000 for Tape Shield, Wire Shield, UniShield, and Longitudinally Corrugated (LC) Cable Instructions IEEE Std. 404 35 kv Class 250 kv BIL F CAUTION
More information3 Foam Sealed Closure 2" (50 mm) with Compound Compression
3 Foam Sealed Closure 2" (50 mm) with Compound Compression Instructions 1.0 General 1.1 The 3M Foam Sealed Closure is designed to be used in the construction and maintenance of buried and underground PIC
More informationWhite Paper. Discone Antenna Design
White Paper Discone Antenna Design Written by Bill Pretty Highpoint Security Technologies Property of Highpoint Security Technologies Inc The user of this document may use the contents to recreate the
More informationANSI/ICEA S STANDARD FOR OPTICAL FIBER OUTSIDE PLANT COMMUNICATIONS CABLE
ANSI/ICEA S-87-640-2016 STANDARD FOR OPTICAL FIBER OUTSIDE PLANT COMMUNICATIONS CABLE August 25, 2016 Sixth Edition Published By Insulated Cable Engineers Association, Inc. (ICEA) www.icea.net Approved
More information3M Cold Shrink Splice Kit QS-III 5416A
3M Cold Shrink Splice Kit QS-III 5416A for Jacketed Concentric Neutral (JCN) and Concentric Neutral Cable Instructions IEEE Std. 404 15 kv Class 150 kv BIL CAUTION Working around energized systems may
More informationWater blocking tape. Locator ridge HPA-0486
Table of Contents STANDARD RECOMMENDED PROCEDURE 004-138 ISSUE 1 MARCH 2012 PAGE 1 OF 12 Sheath Removal and Mid-Span Access of Dielectric ALTOS Cable with FastAccess Technology p/n 004-138, Issue 1 1.
More informationPublic Works Division Lighting District Fiber Optic Specifications April 2009
Public Works Division Lighting District Fiber Optic Specifications April 2009 7000 Florida Street Punta Gorda, Florida 33950 Tele: 941.575.3600 Fax : 941.637.9265 www.charlottecountyfl.com/publicworks
More informationPro-Lock Valve Lockout PRICE LIST
North American Customers ONLY, Please Switch to the USA site Search Home Valve lockout Why Pro-Lock Special Pro-Locks Padlocks & Hasps Polypropylene Seals Cable Seals Prices Contact Us Pro-Lock Valve Lockout
More informationCold Shrink Straight Joint
Cold Shrink Straight Joint 3M QS2000E 22 kv Single Core Straight Joint Instruction Sheet All dimensions shown are in mm unless otherwise stated Kits contains components for one single core cable -2-2*
More informationINDUSTRIAL PROCESS AND COMMERCIAL VENTILATION SYSTEMS. Twin City Fan MODULAR PLENUM FANS MPLFN MPLFS MPLQN MPLQS CATALOG 495 APRIL 2013
Twin City Fan INDUSTRIAL PROCESS AND COMMERCIAL VENTILATION SYSTEMS MODULAR PLENUM FANS MPLFN MPLFS MPLQN MPLQS CATALOG 495 APRIL 2013 PLENUM FANS Models MPLFN MPLFS MPLQN MPLQS Twin City Fan & Blower
More information