High Density Block BRCP. HD BRCP- 128/192/256 pair. Installation Instructions

Size: px
Start display at page:

Download "High Density Block BRCP. HD BRCP- 128/192/256 pair. Installation Instructions"

Transcription

1 High Density Block BRCP HD BRCP- 128/192/256 pair Installation Instructions

2 Product Introduction The BRCP block is the latest generation of MDF terminal blocks developed by 3M, specifically designed for xdsl deployment in the central office and remote sites for DSLAM interconnection with the existing main distribution frame (MDF). The BRCP high density terminal block is modular by design (16-pair modularity) and available in various pair counts enabling perfect match with most DSLAM line card configurations. The BRCP block features a swiveling front and rear side block providing a clear demarcation of two termination areas, one at the rear for the DSLAM vendor installation team (direct termination of DSLAM cables), the other at the front for the xdsl service provider team to jumper its DSL subscribers. 1.0 Kit Contents 3M TM High Density Terminal Block BCRP Note: Examine kit contents. Ensure that all components are present and that they are in a usable and defect free condition. A. 3M HD BRCP Block (1) B. Bolt & Nut M6x20mm (2) C. Cable Ties 2.5mmx100mm (24) - 2 -

3 2.0 Block Identification Terminology Management Rings Block back mount frame Jumper Rings Locking Latch Labels & Label Holder Line identification labels are located at the top of the front face of the block. Free marking area is located at the bottom of the front face of the block. Wire Guides (White or Black) The blocks can be installed horizontally, side by side, or vertically, one above the other

4 3.0 Mounting the Block 3.1 Disengage the locking latches and open the block. Each block element can be secured in the open position. Cable tie ports Cable port Note: When aligning the block onto the vertical frame, ensure that the cable tie ports and the cable port are not obstructed in any way. 3.2 Fix the block back mount frame on the vertical frame. 4.0 Rear Side Termination DSLAM IN & DSLAM OUT Cable Termination Note: Pair 1 on the inside is connected at the bottom of the block element

5 4.1 Route the cable towards the back of the block back mount frame. 4.2 Open the block element and pass the cable through the block back mount frame (leave a minimum of 15" (400 mm) of cable extending from the rear of the back mount frame.) 4.3 Cut the cable sheath approximately 1" (25 mm) from the rear of block back mount frame using company approved tools and practices. Note: Do not completely remove the cable sheath yet. 4.4 Slide the cable sheath down the conductors approximately 10" (250 mm). Note: Keep the outer jacket intact till the cable is out of the port. This would protect the cable from the edges of the port. 4.5 Organize the conductors in bundles of 16 pairs per company practice and color code. 4.6 Remove the remaining section of cable sheath off the conductors

6 4.7 Route the first bundle of 16 pairs of conductors through the management ring. Technical Tip for wiring: For smaller capacities, one half of the block (96 pairs) can be used for DSLAM in and the other half (96 pairs) can be used for DSLAM out. Technical Tip: To ensure sufficient slack during the routing of the pairs, use a piece of scrap cable (or cable jacket) and insert as shown. 4.8 Select the location for the desired pair and route the wires into the corresponding IDC slot. Note: Color code of pairs for internal terminations will be reversed from those of external terminations. 4.9 Terminate the pairs with the approved 3M Termination Tool SOR-OC. Straddle the tool on the IDC contact with the screw head facing toward the middle of the module Push the tool into the module until click is heard, signifying the IDC contact

7 4.11 Remove the wire scrap Route remaining pairs into their corresponding IDC slots Terminate all remaining pairs using the approved SOR-OC termination tool Use cable tie as shown and close the block. Cable Ties Note: Remove the piece of scrap cable (or cable jacket) that might have been used as previously described in the technical tip to ensure sufficient slack during the routing of the pairs. 5.0 Front side termination - Jumper wires Termination (coming from exchange side & line side blocks) Jumpers are terminated one pair at a time. The following steps will be repeated until all required jumper pairs are connected. External conductor terminations are opposite of internal terminations. Pair 1 on the outside is terminated at the top of the block element. Pair 1 for external termination - 7 -

8 5.1 Route jumper into the HD BRCP jumper ring. 5.2 Route the pair of conductors into the wire guide, per company practice and color code. 5.3 Pull the pair of conductors over the corresponding IDC slots, and split the conductors between the slots. 5.4 Terminate the pairs with the approved 3M Termination Tool SOR-OC. Straddle the tool on the IDC contact with the screw head facing toward the middle of the module. 5.5 Push the tool into the module until click is heard, signifying the IDC contact. 5.6 Remove the wire scrap. 5.7 Repeat steps 5.2 through 5.6 until the required jumper terminations are complete

9 6.0 Testing the 3M High Density Block BRCP 6.1 Test Plug To test the HD BRCP block, the 3M Test Plug (SORIB) should be used. Insert the test plug to the port to be tested in the block. This is a polarized test plug; hence it cannot be flipped in the reverse direction. Please ensure that the arrow marked on the rear side of the test plug housing, faces upwards while inserting the test plug. Note: Ensure that the test plug is not inserted in the reverse direction (arrow facing downwards) 6.2 Block Testing To test a pair of upper ports (port no. 1-8) in the module, use the black and red wires at the open end of the test cord, after inserting the plug. To test a pair of lower ports (port no. 9-16) in the module, use the yellow and green wire at the open end of the test cord, after inserting the plug. 7.0 Accessories Termination Tool Test Plug - 9 -

10 3M is a trademark of 3M Company Important Notice All statements, technical information, and recommendations related to 3M s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the products which are not contained in 3M s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. Communication Markets Division 3M Electro & Communications India Pvt Ltd Concorde Block, UB City, 24, Vittal Mallya Road, Bangalore India Board : Fax :

3M Distribution Box (DDB)

3M Distribution Box (DDB) 3M Distribution Box (DDB) Merged Copper and Fiber Pole/Post Mount Enclosure Installation Instructions November 2015 78-0015-2736-1-A 2 November 2015 78-0015-2736-1-A Contents 1.0 General 2.0 Enclosure

More information

3M Coupling Tray FDTC-10S-COUPLINGTRAY

3M Coupling Tray FDTC-10S-COUPLINGTRAY 3M Coupling Tray FDTC-10S-COUPLINGTRAY for use with 3M Fiber Dome Closures FDC 10S Instructions July 2010 3 1.0 Introduction The 3M Coupling Tray FDTC-10S-COUPLINGTRAY can accommodate up to 10 loose tubes.

More information

2179-CD Series Fiber Optic Splice Closure. Installation Instructions

2179-CD Series Fiber Optic Splice Closure. Installation Instructions 2179-CD Series Fiber Optic Splice Closure Installation Instructions 1.0 Product Introduction The new 3M TM 2179-CD Series Fiber Optic Splice Closure can be used in buried, underground, aerial, and pedestal

More information

SLiC Fiber Aerial Closure System

SLiC Fiber Aerial Closure System 3 SLiC Fiber Aerial Closure System SLFC 533-SP SLFC 533-TS SLFC 733-SP Instructions May 2005 78-8135-4502-3-B N C H E S R A N G E M IL L IM E T E R S.4 10.6.8 A B C 15 20 I 1.0 Kit Contents Note: Examine

More information

3 SLiC Aerial Closure with Rubber End Seal

3 SLiC Aerial Closure with Rubber End Seal 3 Aerial Closure with Rubber End Seal Instructions 1.0 General 1.1 This instruction bulletin describes the assembly of the 3M Aerial Closure with external bonding hanger brackets. These closures are suitable

More information

3M Locator Plate N

3M Locator Plate N M Locator Plate 44-107N Instructions for the assembly of.100 x.100 preassembled socket connectors 1.0 General The M Locator Plate 44-107N is designed to aid in the assembly of the preassembled socket connector

More information

3M Fiber Optic Splice Tray 2527 with 3M PLC Optical Splitter

3M Fiber Optic Splice Tray 2527 with 3M PLC Optical Splitter 3M Fiber Optic Splice Tray 2527 with 3M PLC Optical Splitter Instructions January 2010 3 1.0 General 1.1 The 3M Fiber Optic Splice Tray 2527 with 3M PLC Optical Splitter(s) protects, organizes and stores

More information

3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR 3M Cable Addition Kit 2181-XL and 2181-XL/FR

3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR 3M Cable Addition Kit 2181-XL and 2181-XL/FR 3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR 3M Cable Addition Kit 2181-XL and 2181-XL/FR Instructions July 2010 3 1.0 Contents 1.0 General...3 2.0 Kit Contents...3 3.0 Cable Preparation...4 4.0

More information

4320 SS-25 Self-Strip Terminating Block

4320 SS-25 Self-Strip Terminating Block 4320 SS-25 Self-Strip Terminating Block Instructions May 2002 78-8130-7677-1 1.0 General The 3M 4320 SS-25 Self-Strip Terminating Block is a factory stubbed, self-stripping connecting block designed for

More information

3M Fiber Optic Splice Closure 2178-XSB/XSB-FR & 2178-XLB/XLB-FR 3M Cable Addition Kit 2181-XB/XB-FR

3M Fiber Optic Splice Closure 2178-XSB/XSB-FR & 2178-XLB/XLB-FR 3M Cable Addition Kit 2181-XB/XB-FR 3M Fiber Optic Splice Closure 2178-XSB/XSB-FR & 2178-XLB/XLB-FR 3M Cable Addition Kit 2181-XB/XB-FR Instructions July 2010 78-8135-0094-5-K 3 1.0 General 1.1 3M Fiber Optic Splice Closure 2178-XSB The

More information

3M Slim Lock Closures

3M Slim Lock Closures 3M Health Care 3M Slim Lock Closures 3M Tower Weatherproofing Solutions Sesh Natarajan 3M Health Care 3M Tower Weatherproofing Solutions Market trend towards denser RF connectors on tower equipment Macro

More information

3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR

3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR 3M Fiber Optic Splice Closure 2178-XL & 2178-XL/FR 3M Cable Addition Kit 2181-XL and 2181-XL/FR Instructions September 2017 78-8130-5055-2-M 2 September 2017 78-8130-5055-2-M 1.0 Kit Contents 2.0 General...

More information

3M SLiC 530/533/733-2 Port 0.61 Cable Entry Bracket 3M SLiC 530/533/733-2 Port-MSM 0.61 Cable Entry Bracket

3M SLiC 530/533/733-2 Port 0.61 Cable Entry Bracket 3M SLiC 530/533/733-2 Port-MSM 0.61 Cable Entry Bracket 3M SLiC 530/533/733-2 Port 0.61 Cable Entry Bracket 3M SLiC 530/533/733-2 Port-MSM 0.61 Cable Entry Bracket For use with 3M SLiC Free-Breathing Fiber Optic Closures and Terminals Instructions November

More information

18mm ECAM Cable Entry Port

18mm ECAM Cable Entry Port 18mm ECAM Cable Entry Port Instructions October 2006 1.0 Introduction The 3M 18mm ECAM (External Cable Assembly Module) Cable Entry Port Kit is designed to accept fiber optic cables with external diameters

More information

Quante BPEO Splice-Protection Closure for Optical Fiber Cables. Features Advantages Benefits

Quante BPEO Splice-Protection Closure for Optical Fiber Cables. Features Advantages Benefits 3 Quante BPEO Splice-Protection Closure for Optical Fiber Cables BPEO: Fully Mechanical, Easy to Install, No Specific Tools BPEO is the newest generation of watertight spliceprotection closures for optical

More information

3M Scotchcast Reenterable Signal and Control Cable Splicing Kits 78-R Series

3M Scotchcast Reenterable Signal and Control Cable Splicing Kits 78-R Series 3M Scotchcast Reenterable Signal and Control Cable Splicing Kits 78-R Series Instructions Voltage Rating: 1000 V, Temperature Rating: 90 C Kit Contents 78-R1 78-R2 78-R3 78-R4 78-R5 Sleeve Set 1 1 1 1

More information

Cabinet Tools and Accessories Ordering Guide

Cabinet Tools and Accessories Ordering Guide 3 Cabinet Tools and Accessories Ordering Guide 3M Cabinet Tools and Accessories 3M 4320 Block Spare Parts Replacement Cap Kit 100 Tan + 100 Orange 1/cs. 1/cs. 054007-63793 Half-tap, feed through 100 Tan

More information

FOSC-600 C and D I N S T A L L A T I O N I N S T R U C T I O N

FOSC-600 C and D I N S T A L L A T I O N I N S T R U C T I O N FOSC-600 C and D I N S T A L L A T I O N I N S T R U C T I O N In-line and butt version Cold applied re-usable fiber optic closure Contents 1 Introduction 1.1 Product description 1.2 Capacity 2 General

More information

3M Better Buried Compound Compression Closure System

3M Better Buried Compound Compression Closure System 3M Better Buried Compound Compression Closure System Instructions March 2016 78-0015-2948-2-A Contents: 1.0 General...3 2.0 Kit Contents...3 3.0 Closure Selection Guide...4 4.0 LHS End Cap Installation...5

More information

Solutions for Electronic Specialty Markets (ESM)

Solutions for Electronic Specialty Markets (ESM) 3M Worldwide : United States : Electronics Manufacturing Solutions for Electronic Specialty Markets (ESM) Product Catalog for Electronic Specialty Markets 3M Electronic Specialty Markets - New Product

More information

SLiC Fiber Aerial Closure 533 and 733

SLiC Fiber Aerial Closure 533 and 733 SLiC Fiber Aerial Closure 533 and 733 3M s SLiC fiber aerial closures are designed to enable service providers to costeffectively deploy aerial fiber networks in the access network (FTTN, HFC, and FTTP).

More information

3M No Polish Jacketed SC/APC Connector

3M No Polish Jacketed SC/APC Connector Communication Markets Division 3M No Polish Jacketed SC/APC Connector For use with 1.6 to 3.0 mm Jacketed Cable 3M No Polish SC/APC Connector enables fast, on-site termination of 1.6 mm to 3.0 mm jacketed

More information

Instruction Guide February 2017

Instruction Guide February 2017 Instruction Guide February 2017 3M Instruction Guide: 3M TM Locator Plate 3443-81-XX, 3D-Printed Instructions for the assembly of 3M TM Ribbon Cable Wiremount Socket Assembly, 451 Series 1.0 General 1.1

More information

Instructions. Cable with Armor F CAUTION. October Rev A

Instructions. Cable with Armor F CAUTION. October Rev A 3M Single Conductor Accessory Breakout Kits (BOK's) for use with 3M Cable Accessories (Terminations, T-Bodies and Push-On Elbows) For Use With Single Conductor Accessories On Three-Core Conductor Cables

More information

3M Better Buried Closure (with 3M Scotchlok Shield Bond Connector 4462-FN and 3M High Gel Re-enterable Encapsulant 8882)

3M Better Buried Closure (with 3M Scotchlok Shield Bond Connector 4462-FN and 3M High Gel Re-enterable Encapsulant 8882) 3M Better Buried Closure (with 3M Scotchlok Shield Bond Connector 4462FN and 3M High Gel Reenterable Encapsulant 8882) Instructions April 2016 78813509979C Contents: 1.0 General... 1 2.0 Kit Contents...

More information

3M Better Buried Closures

3M Better Buried Closures 3M Better Buried Closures Instructions March 2016 78-0015-2945-8-A Contents: 1.0 General... 3 2.0 Kit Contents... 3 3.0 Closure Selection Guide... 4 4.0 LHS End Cap Installation... 5 5.0 Cable Preparations...

More information

3M Cross-Connect Cabinets 4220SVB, 4220SVC and 4220SVE 3M Junction Box (JBOX)

3M Cross-Connect Cabinets 4220SVB, 4220SVC and 4220SVE 3M Junction Box (JBOX) 3M Cross-Connect Cabinets 4220SVB, 4220SVC and 4220SVE 3M Junction Box (JBOX) In-cabinet and Outdoor AC Power Junction Box (JBOX) for 3M Cross-Connect Cabinets with DSLAM apparatus cases installed Instructions

More information

3M Cold Shrink Foldback Splice Jacket Kit

3M Cold Shrink Foldback Splice Jacket Kit 3M Cold Shrink Foldback Splice Jacket Kit SJ-FB Instructions! CAUTION Working around energized systems may cause serious injury or death. Installation should be performed by personnel familiar with good

More information

FOSC-450D. Fiber Optic Splice Closure. 1 Introduction. Content. 5 Cable termination. 6 Fiber routing. 2 General. 7 Installation of the gel block

FOSC-450D. Fiber Optic Splice Closure. 1 Introduction. Content. 5 Cable termination. 6 Fiber routing. 2 General. 7 Installation of the gel block FOSC-450D I N S T A L L A T I O N I N S T R U C T I O N Fiber Optic Splice Closure Content 1 Introduction 2 General 2.1 Kit content 2.2 Tools 2.3 Accessories 2.4 Capacity 3 Preparation of the closure 4

More information

3M Fiber Optic Closure System LL

3M Fiber Optic Closure System LL 3M Fiber Optic Closure System LL 3M Fiber Optic Closure System The 3M Fiber Optic Closure System LL provides a protective yet accessible environment for housing single or mass fusion fiber splices. The

More information

3M Fiber Closures BPEO

3M Fiber Closures BPEO 3M Fiber Closures BPEO 2 3M Fiber Closures BPEO The 3M Fiber Closures BPEO are designed with flexibility in application in mind. With a range of sizes, they can be deployed above grade (pole, facade) or

More information

3M Cross-Connect Cabinets 4220SVB, 4220SVC and 4220SVE Skirt and Stabilizers

3M Cross-Connect Cabinets 4220SVB, 4220SVC and 4220SVE Skirt and Stabilizers 3M Cross-Connect Cabinets 4220SVB, 4220SVC and 4220SVE Skirt and Stabilizers Rear skirt and stabilizers to cover and protect DSLAM apparatus cases mounted directly on 3M Pad or Stake Mount Cabinets Instructions

More information

3M Fiber Optic Wall Mount Enclosure 8430 Series

3M Fiber Optic Wall Mount Enclosure 8430 Series 3M Fiber Optic Wall Mount Enclosure 8430 Series Installation Instructions January 2014 3 78-0013-9429-1-A Table of Contents 1.0 Description...3 2.0 Parts...4 3.0 Assembly...4 4.0 Mounting the Enclosure...6

More information

3M Sensored Termination (15 kv) QX-T15I-vi1-E

3M Sensored Termination (15 kv) QX-T15I-vi1-E 3M Sensored Termination () QX-T15I-vi1-E Data Sheet May 2016 Kit Contents: Each kit contains sufficient quantities of the following materials to make three single-phase terminations. 31" (REF) One piece

More information

Communication Markets Division. 3M Fiber Closures. Smart design makes your job easier.

Communication Markets Division. 3M Fiber Closures. Smart design makes your job easier. Communication Markets Division 3M Fiber Closures Smart design makes your job easier. 2 Your connections deserve the best protection. No matter the size and configuration of your network, protecting its

More information

6000 Series Patch Panel Terminating Instructions

6000 Series Patch Panel Terminating Instructions 6000 Series Patch Panel Terminating Instructions INTRODUCTION The 6000 Series patch panels include a unique feature not found on any other patch panel. This feature allows you to angle each of the four

More information

Installation Instructions

Installation Instructions TECP-30-260 Issue 2 July 2016 Installation Instructions OWB-S OWB-S Small Wall-mounted Box CONTENTS 1. Introduction 2. Kit content 3. Installation Instruction 3.1. Box installation 3.2. Conduit installation

More information

3 Foam Sealed Closure 2" (50 mm) with Compound Compression

3 Foam Sealed Closure 2 (50 mm) with Compound Compression 3 Foam Sealed Closure 2" (50 mm) with Compound Compression Instructions 1.0 General 1.1 The 3M Foam Sealed Closure is designed to be used in the construction and maintenance of buried and underground PIC

More information

3M 8900 Single-mode SC Crimplok Connector

3M 8900 Single-mode SC Crimplok Connector 3M 8900 Single-mode SC Crimplok Connector Technical Report June 1999 80-6110-1441-8 1 1.0 Product Description & Requirements The 3M SC Single-mode Crimplok Connector is designed to provide the customer

More information

3 Closure preparation 3.1 Work-stand 3.2. Opening FIST-GCOG2-Dx Preparing drop cable with micro-tubes

3 Closure preparation 3.1 Work-stand 3.2. Opening FIST-GCOG2-Dx Preparing drop cable with micro-tubes FIST-GCOG2-Dx24 I N S T A L L A T I O N I N S T R U C T I O N FTTH closure for micro-tubes and micro-cables Content 1 Introduction 2 Kit content 3 Closure preparation 3.1 Work-stand 3.2. Opening FIST-GCOG2-Dx24

More information

3M No Polish Jacketed SC/APC Connector

3M No Polish Jacketed SC/APC Connector Communication Markets Division 3M No Polish Jacketed SC/APC Connector For use with 1.6 to 3.0 mm Jacketed Cable 3M No Polish SC/APC Connector enables fast, on-site termination of 1.6 mm to 3.0 mm jacketed

More information

3M We are Projectors! When the show must go on, 3M makes it easy:

3M We are Projectors! When the show must go on, 3M makes it easy: 3M Digital Projectors Digital Projector Family Brochure When the show must go on, 3M makes it easy: Whether it s a daily briefi ng, a classroom presentation, or your annual customer conference, you want

More information

FOSC 450 C6 and D6 Closures

FOSC 450 C6 and D6 Closures FOSC 450 C6 and D6 Closures I N S T A L L A T I O N I N S T R U C T I O N Fiber Optic Splice Closure 1. General Product Information The FOSC 450 C6 and D6 fiber optic splice closures use compressed gel

More information

3M Motor Lead Inline Splice 5331, 5332, 5333 & 5334

3M Motor Lead Inline Splice 5331, 5332, 5333 & 5334 3M Motor Lead Inline Splice 5331, 5332, 5333 & 5334 for 5/8 kv Non-Shielded and Shielded Cables (Ribbon, Wire and UniShield Cables) Instructions Cable Size Range: Feeder: #8 AWG 500 kcmil Motor Lead: #10

More information

Scotch Heavy Duty Vinyl Electrical Tape 22

Scotch Heavy Duty Vinyl Electrical Tape 22 Scotch Heavy Duty Vinyl Electrical Tape 22 Data Sheet July 2015 Description Agency Approvals & Self Certifications Scotch Heavy Duty Vinyl Electrical Tape 22 is a premium grade, 10-mil thick, vinyl insulating

More information

3M Scotchcast Mine and Portable Cable Splice and Jacket Repair Kit M-40

3M Scotchcast Mine and Portable Cable Splice and Jacket Repair Kit M-40 3M Scotchcast Mine and Portable Cable Splice and Jacket Repair Kit M-40 Instructions 1 & 2 For Jacket Repair (pages 2 & 7) Supplemental Instructions for: Insulation Repair (page 12) Conductor Repair (page

More information

3M Scotchcast Flexible Power Cable Splice Kits 82-F Series

3M Scotchcast Flexible Power Cable Splice Kits 82-F Series 3M Scotchcast Flexible Power Cable Splice Kits 82-F Series For use in weather-exposed, direct burial or submerged locations. For making in-line splices on non-shielded portable power cables and cords rated

More information

3M Cold Shrink Splice Kit QS-III 5416A

3M Cold Shrink Splice Kit QS-III 5416A 3M Cold Shrink Splice Kit QS-III 5416A for Jacketed Concentric Neutral (JCN) and Concentric Neutral Cable Instructions IEEE Std. 404 15 kv Class 150 kv BIL CAUTION Working around energized systems may

More information

3M Cold Shrink QS-III Silicone Rubber Splice Kit 5488A-TOW/WOT

3M Cold Shrink QS-III Silicone Rubber Splice Kit 5488A-TOW/WOT 3M Cold Shrink QS-III Silicone Rubber Splice Kit 5488A-TOW/WOT For Tape Over Wire (TOW) and Wire-Over-Tape (WOT) Shielded Cable For 250 2000 kcmil cable with 650-mil primary insulation thickness Instructions

More information

QCA9-33 Active Combiner

QCA9-33 Active Combiner Product Manual QCA9-33 Active Combiner April 13, 2012 Table of Contents Table of Contents... 2 Overview... 3 Specifications... 4 Installation... 5 Basic Setup... 5 16-Channel Operation... 5 16-64 Channel

More information

3M Cold Shrink Splice Kit QS-III 5514A

3M Cold Shrink Splice Kit QS-III 5514A 3M Cold Shrink Splice Kit QS-III 5514A for UniShield, Wire Shielded, Longitudinally Corrugated (LC), and Tape Shielded (Ribbon Shielded) Cable or Transitions to Concentric Neutral (CN)/Jacketed Concentric

More information

Medium Box for Cable Termination

Medium Box for Cable Termination FIST-MB2-T I N S T A L L A T I O N I N S T R U C T I O N Medium Box for Cable Termination Contents 1 Introduction 1.1 Product description. 2 General 2.1 Tools 2.2 Kit contents 3 Installation and pre assembling

More information

USER S MANUAL. Save this manual for future reference. For a digital version of this manual, visit

USER S MANUAL. Save this manual for future reference. For a digital version of this manual, visit TM USER S MANUAL Save this manual for future reference. For a digital version of this manual, visit www.mylifter.com/installation. 4 5 TABLE OF CONTENTS 4 INSTALLING THE PULLEY SYSTEM FOR LIFTING 100

More information

3M Cold Shrink Splice Kit QS-III 5515A

3M Cold Shrink Splice Kit QS-III 5515A 3M Cold Shrink Splice Kit QS-III 5515A for UniShield, Wire Shielded, Longitudinally Corrugated (LC), and Tape Shielded (Ribbon Shielded) Cable or Transitions to Concentric Neutral (CN)/Jacketed Concentric

More information

3M New Construction Cross-Connect Cabinets. The. Commitment. Your Copper Requires

3M New Construction Cross-Connect Cabinets. The. Commitment. Your Copper Requires 3M New Construction Cross-Connect Cabinets Commitment The Your Copper Requires 3M. A pioneer. A partner. Copper is the foundation of your distribution network, now and for the foreseeable future. It s

More information

Cold Shrink Three-Conductor Splice Kit QS-III for use on Armor and Non-Armor Cables Instructions IEEE Std kv Class 250 kv BIL

Cold Shrink Three-Conductor Splice Kit QS-III for use on Armor and Non-Armor Cables Instructions IEEE Std kv Class 250 kv BIL Cold Shrink Three-Conductor Splice Kit QS-III for use on Armor and Non-Armor Cables Instructions IEEE Std. 404 35 kv Class 250 kv BIL Kit Number 5798A-MT Cable Range Requirements Cable Insulation O.D.

More information

3M Merchandising Catalog. Unrivaled. Product Presence to. Meet Your Merchandising Needs

3M Merchandising Catalog. Unrivaled. Product Presence to. Meet Your Merchandising Needs 3M Merchandising Catalog Unrivaled Product Presence to Meet Your Merchandising Needs 1 Table of Contents Gondolas...3-5 Shelves...6-7 Racks...8-10 Portable Labeler Displays...11-14 Terminals Displays...15-17

More information

FIST-GCO2-OTIAN I N S T A L L A T I O N I N S T R U C T I O N

FIST-GCO2-OTIAN I N S T A L L A T I O N I N S T R U C T I O N FIST-GCO2-OTIAN I N S T A L L A T I O N I N S T R U C T I O N 24 Address Point Fibre distribution point (FDP) Installation guide for fibre DP Contents 1 Kit Contents 2 Accessories 3 MOBRA installation

More information

FIST-MB2-S. FIST Medium Box for Cable Splicing Only. 4 Cable installation. 1 Introduction. Contents. 2 General. 5. Fiber routing to individual trays

FIST-MB2-S. FIST Medium Box for Cable Splicing Only. 4 Cable installation. 1 Introduction. Contents. 2 General. 5. Fiber routing to individual trays FIST-MB2-S I N S T A L L A T I O N I N S T R U C T I O N FIST Medium Box for Cable Splicing Only Contents 1 Introduction 1.1 Product description 2 General 2.1 Tools 2.2 Kit contents 3 Installation and

More information

27mm ECAM Double Cable Entry Port

27mm ECAM Double Cable Entry Port 27mm ECAM Double Cable Entry Port Instructions October 2006 1.0 Introduction The 3M 27mm ECAM Double Cable (External Cable Assembly Module) Entry Port is designed to accept fiber optic loose tube & central

More information

Quick Release Roof-Mount Kit MB700

Quick Release Roof-Mount Kit MB700 Quick Release Roof-Mount Kit MB700 Owner s Manual Thank you for purchasing a KING product! The KING Quick Release Roof-Mount provides a convenient way to securely mount your KING antenna to your vehicle,

More information

Clearview. Classic Cassettes. Installation Manual. Clearview Classic (HD) High Density. Part #: Rev: A Updated:

Clearview. Classic Cassettes. Installation Manual. Clearview Classic (HD) High Density. Part #: Rev: A Updated: Clearview Classic Cassettes Installation Manual Clearview Classic (HD) High Density Part #: 016781 Rev: A Updated: 11.2014 7050 Winnetka Ave N Minneapolis, MN 55428 Direct: 763.476.6866 National: 800.422.2537

More information

2178-L/S Series Fiber Optic Splice Case with Gasket

2178-L/S Series Fiber Optic Splice Case with Gasket 2178-L/S Series Fiber Optic Splice Case with Gasket Instructions for: 2178-S Splice Case 2178-LS Splice Case 2178-LL Splice Case 2181-LS Cable Addition Kit May 1997 34-7041-9949-5-A 1 Table of Contents

More information

K & B Flame Retardant Building Riser Closures

K & B Flame Retardant Building Riser Closures K & B Flame Retardant Building Riser Closures September 1995 Issue 1, 34-7016-7030-8 1. General 1.1 3M Brand K&B Building Riser Closures are designed for use in building riser closets and may be positioned

More information

Scotchlok Connectors and Tools

Scotchlok Connectors and Tools Scotchlok Connectors and Tools Proven Solutions For Today s Applications A New Series of Tools and Connectors from 3M. Over 45 years ago, 3M introduced the industry s original insulation displacement connector

More information

3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN-4/0-500

3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN-4/0-500 3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN-4/0-500 for Jacketed Concentric Neutral (JCN) and Flat Strap Neutral Cable Instructions IEEE Std. 404 15 kv Class 150 kv BIL CAUTION Working around energized

More information

3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN

3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN 3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN-500-1000 for Jacketed Concentric Neutral (JCN) and Flat Strap Neutral Cable Instructions IEEE Std. 404 15 kv Class 150 kv BIL F CAUTION Working around

More information

QDA4-44 RF Amp/Combiner

QDA4-44 RF Amp/Combiner Product Manual QDA4-44 RF Amp/Combiner May 17, 2012 Table of Contents Table of Contents... 2 Overview... 3 Specifications... 4 Installation... 5 Basic Setup... 5 Rack Mounting... 6 RK2 Dual Rack Kit with

More information

3M Mini D Ribbon (MDR) Cable Assembly

3M Mini D Ribbon (MDR) Cable Assembly 3M Mini D Ribbon (MDR) Cable Assembly.050 Digital Camera Extension Cable 26 position 1WL26-TZ3B-XXX-03C Mates to popular 3M MDR 26 position receptacle on one end, and to another MDR 26 position cable assembly

More information

CR-R880-BL: Indoor/Outdoor Proximity Reader with 10cm (4in) read range

CR-R880-BL: Indoor/Outdoor Proximity Reader with 10cm (4in) read range CR-R880-BL: Indoor/Outdoor Proximity Reader with 10cm (4in) read range Installation Manual Table of Contents Basic Operation...2 CR-R880-BL Block Diagram...2 Technical Specifications...3 Features...4

More information

TRIPLETT. PairMaster. Lan Cable Test Set. Instruction Manual

TRIPLETT. PairMaster. Lan Cable Test Set. Instruction Manual TRIPLETT PairMaster Lan Cable Test Set Instruction Manual The PairMaster LAN CABLE TEST SET INSTRUCTION MANUAL IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Before using the PairMaster, read all

More information

Volition TM RJ45 K5e Jacks

Volition TM RJ45 K5e Jacks Volition TM RJ45 K5e Jacks Part of our 3M Volition Network Solutions, the new K5e range is our ultimate Category 5e hardware component (ISO/IEC 11801, EN 50173 and ANSI/TIA/EIA-568). The K5e jack is a

More information

24-Fiber LANLINXS (Model # ) 48-Fiber LANLINXS (Model # ) User Manual

24-Fiber LANLINXS (Model # ) 48-Fiber LANLINXS (Model # ) User Manual 24-Fiber LANLINXS (Model # 055-8632-5000) 48-Fiber LANLINXS (Model # 055-8832-5000) User Manual 24-Fiber LANLINXS (Model # 055-8632-5000) 48-Fiber LANLINXS (Model # 055-8832-5000) User Manual, Part Number

More information

Atlona HDBaseT-Lite Transmitter over Single CAT5e/6/7

Atlona HDBaseT-Lite Transmitter over Single CAT5e/6/7 Atlona HDBaseT-Lite Transmitter over Single CAT5e/6/7 AT-HDTX User Manual Table of Contents 1. Introduction... 3 2. Package Contents... 3 3. Features... 3 4. Specifications... 3 5. Panel Descriptions a.

More information

User Manual CXE Rev (12) CXX Series. User Manual. Teleste Corporation CXE810. Fibre optic receiver

User Manual CXE Rev (12) CXX Series. User Manual. Teleste Corporation CXE810. Fibre optic receiver 27.3.2012 1(12) CXX Series User Manual Teleste Corporation CXE810 Fibre optic receiver 27.3.2012 2(12) Contents Introduction... 3 Installation... 3 Housing... 3 Powering... 4 Interfaces... 4 Fibre installation...

More information

3M Super 23 Electrical Tape

3M Super 23 Electrical Tape WEATHERPROOFING S CHEMICALS ET 3M SUPER 23 Features: Premium all-weather black electrical tape Remains conformable at -18 C /0 F 7mm thickness UV resistant Part # Size ET 3M Super 23 19mm x 9.15m WEATHERPROOFING

More information

3M Cold Shrink QS4 Integrated Splice Kit QS4-35TS

3M Cold Shrink QS4 Integrated Splice Kit QS4-35TS 3M Cold Shrink QS4 Integrated Splice Kit QS4-35TS-350-1000 for Tape Shield, Wire Shield, UniShield, and Longitudinally Corrugated (LC) Cable Instructions IEEE Std. 404 35 kv Class 250 kv BIL F CAUTION

More information

Gel-sealed in-line fiber optic closure

Gel-sealed in-line fiber optic closure SCIL-C Gel donut INSTALLATION INSTRUCTION TC-1363-1-IP Rev A, Oct 2017 www.commscope.com Gel-sealed in-line fiber optic closure Contents 1 General 2 Sizing and product kit information 3 Installation conditions

More information

Dynatel Advanced Cable Locator 2250

Dynatel Advanced Cable Locator 2250 3 Dynatel Advanced Cable Locator 2250 Quickly and Accurately Identify Underground Assets Pinpoint exact cable path and depth quickly and easily with this lightweight, easy-to-handle unit The 3M Dynatel

More information

3M MetPak 2-FB Header

3M MetPak 2-FB Header M MetPak 2-FB Header Solder Tail End-to-end stackable Select load capability Monoblockable Shoulder Pin Press Fit End-to-end stackable Early mate late break for hot swapping (press-fit EMLB adjusted by

More information

DS1 Cross-Aisle Panel

DS1 Cross-Aisle Panel DS1 Cross-Aisle Panel Model 005-0005-0100 Installation Guide 1.1 Overview 1.1.1 Inspection Compare the contents of the DS1 Cross-Aisle Panel shipping container with the packing list. Call Telect if anything

More information

Built tough for long-term connections

Built tough for long-term connections Communication Markets Division 3M Scotchlok Connectors Built tough for long-term connections 2 3 Durable, insulated connections on the first crimp. Over 50 years ago, 3M introduced the industry s original

More information

Communication Markets Division 3M Scotchlok Connectors and Tools. Proven. Solutions for. Today s Applications

Communication Markets Division 3M Scotchlok Connectors and Tools. Proven. Solutions for. Today s Applications Communication Markets Division 3M Scotchlok Connectors and Tools Proven Solutions for Today s Applications A Proven Series of Tools and Connectors from 3M. 50 years ago, 3M introduced the industry s original

More information

Built tough for long-term connections

Built tough for long-term connections Communication Markets Division 3M Scotchlok Connectors Built tough for long-term connections 2 3 Durable, insulated connections on the first crimp. Over 50 years ago, 3M introduced the industry s original

More information

LWX-1. Satellite Weather Radio Module Installation Instructions A

LWX-1. Satellite Weather Radio Module Installation Instructions A LWX-1 Satellite Weather Radio Module Installation Instructions 988-0158-13A Copyright 2009 Navico All rights reserved. No part of this manual may be copied, reproduced, republished, transmitted or distributed

More information

TV Lift System Model CL-65 Installation Instructions

TV Lift System Model CL-65 Installation Instructions TV Lift System Model CL-65 Installation Instructions Contact: Support@Nexus21.com Toll Free: (866) 500-5438 Phone: (480) 951-6885 Fax: (480) 951-6879 Revised: 01/17/17 Below is a parts list describing

More information

Model R177M and R177S Baseband Switch

Model R177M and R177S Baseband Switch Model R177M and R177S Baseband Switch Installation Guide P/N 1340192 082304 Monroe Electronics 100 Housel Ave Lyndonville NY 14098-0535 800-821-6001 585-765-2254 fax 585-765-9330 www.monroe-electronics.com

More information

HTP1502W1 Remote Controlled Multicolor Lighting System

HTP1502W1 Remote Controlled Multicolor Lighting System Page 1 of 8 CHATSWORTH, CALIFORNIA 91311 USA www.cyron.com HTP1502W1 Remote Controlled Multicolor Lighting System Thank you for purchasing CYRON HTP1502W1 LED Lighting System. This system will bring the

More information

2178 Fiber Optic Splice Case and 2181 Cable Addition Kit

2178 Fiber Optic Splice Case and 2181 Cable Addition Kit 2178 Fiber Optic Splice Case and 2181 Cable Addition Kit Instructions January 1994 Issue 1, 34-7029-6387-6 1 2 Contents: 1.0 General... 4 2.0 Specifications... 4 3.0 Kit Contents... 5 SECTION 1: 2178 Splice

More information

F CAUTION. Jacketed Concentric Neutral (JCN) Cable. Concentric Neutral (CN) Cable. IEEE Std. No. 48 Class 1 Termination 15 kv Class 110 kv BIL

F CAUTION. Jacketed Concentric Neutral (JCN) Cable. Concentric Neutral (CN) Cable. IEEE Std. No. 48 Class 1 Termination 15 kv Class 110 kv BIL 3M Cold Shrink QT-III Silicone Rubber Skirted Termination Kit With High-K Stress Relief 7642-S-2 For Jacketed Concentric Neutral (JCN) and Concentric Neutral (CN) Cable Instructions IEEE Std. No. 48 Class

More information

Instructions for Use of Overlap Seam Repair Kit:

Instructions for Use of Overlap Seam Repair Kit: Instructions for Use of Overlap Seam Repair Kit: 3M has assembled a field repair kit to adhesively re-attach delaminated overlap seams on trailers or truck body sidewalls. If the overlap seams were previously

More information

MaxView Cinema Kit Quick Install Guide

MaxView Cinema Kit Quick Install Guide SYSTEM SETUP The MaxView will work at any of the following display settings: INSTALLATION MaxView Cinema Kit Quick Install Guide Step 1 - Turn off your computer. Disconnect your monitor s VGA cable from

More information

HD Flex Patch Panel. ASSEMBLY VIEW (FLEX1UPN** shown) FS128B. CONTENTS: (#) indicates FLEX4UPN** quantity

HD Flex Patch Panel. ASSEMBLY VIEW (FLEX1UPN** shown) FS128B. CONTENTS: (#) indicates FLEX4UPN** quantity HD Flex Patch Panel Part Numbers: FLEX1UPN**, FLEX2UPN**, FLEX4UPN** Panduit Corp. 2018 INSTALLATION INSTRUCTIONS Note: HD Flex Patch Panels are compatible with HD Flex Fiber System Components. HD Flex

More information

Installation instructions Roxtec RM BG systems

Installation instructions Roxtec RM BG systems Safety information Roxtec recommends that all installations are performed without facility operation. Follow national regulations and installation codes. ny action affecting the routed service should be

More information

RAIL D-SUB BACKSHELLS

RAIL D-SUB BACKSHELLS RAIL D-SUB BACKSHELLS FOR D-SUBMINIATURE CONNECTORS D-SUB BACK SHELLS /// DATA SHEET RAIL D-SUB BACKSHELLS FOR D-SUBMINIATURE CONNECTORS TE Connectivity (TE) provide a comprehensive range of ruggedized

More information

Quick Start Guide ABOUT THE CAMERA

Quick Start Guide ABOUT THE CAMERA User Manual Quick Start Guide ABOUT THE CAMERA A Record Status B Record Switch C Rotating Lens D Battery Slot E Battery Latch F Card Format Button G USB H Format Switch I MicroSD card J Memory Status K

More information

3M Pressurized Closure System 2-Type 505

3M Pressurized Closure System 2-Type 505 Communication Markets Division 3M Pressurized Closure System 2-Type 505 The 3M Pressurized Closure System 2-Type 505 is a complete, pressuretight, re-enterable closure system for enclosing spliced connections

More information

XW3D. Simple Wiring of Sensor Actuators. Connector Terminal Boxes. Specifications. Materials and Finish. Connection Combinations

XW3D. Simple Wiring of Sensor Actuators. Connector Terminal Boxes. Specifications. Materials and Finish. Connection Combinations Terminal Boxes XWD CSM_XWD_DS_E Simple Wiring of Sensor Actuators Greatly reduce wiring in combination with the Smartclick XS. Insert the connector and turn / of a turn to lock the connectors. Higher rated

More information

Owner s Manual. RJ11/RJ12/RJ45 Cable Crimper/Stripper with Built-In Tester. Model: T TST

Owner s Manual. RJ11/RJ12/RJ45 Cable Crimper/Stripper with Built-In Tester. Model: T TST Owner s Manual RJ11/RJ12/RJ45 Cable Crimper/Stripper with Built-In Tester Model: T100-001-TST Este manual esta disponible en español en la página de Tripp Lite: www.tripplite.com Ce manuel est disponible

More information

Installation instructions Roxtec RM BG B systems

Installation instructions Roxtec RM BG B systems Safety information Roxtec recommends that all installations are performed without facility operation. Follow national regulations and installation codes. ny action affecting the routed service should be

More information