Instruction Manual. from software version 1.00/30 (Instruction version 1.00) Internet:

Transcription

1 Instruction Manual RGB Static from software version 1.00/30 (Instruction version 1.00) Internet:

2 Notes: GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 2

3 Table of content 1 Description of Device Safety Instructions Preparation and Installation Mounting Mounting on the Floor (Upright) Mounting in hanging Position (Head first) Mounting in sidewise Position Secure the Device Connections Power Supply DMX The Menu Field DMX Channel Selection (DMX Protocol) Maintaining and Cleaning the IMPRESSION Safety regulations Circumference and Interval (rule-of-thumb) Technical Specifications Index GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 3

4 1 Description of Device R-G-B Static 1. Moving head (actively and passively cooled) 2. Arm with various cooling vents 3. LCD-Display/Menu (data entry) 4. Base with various connectors and Camlock mounting system ba se sid e b a se sid e 2 5. Power On/Off 6. DMX- Output (3 pole) 7. DMX- Input (3 pole) 8. Micro-fuse 5x20mm, T4A 9. Mains supply (Powercon) 10. 2x Safety eyes FUSE T4A GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 4

5 1.1 Safety Instructions The IMPRESSION is a High-Tech Product. To guarantee a smooth operation, it is necessary to respect the following rules. The manufacturer of this device will not take responsibility of damages through any disregard of the information in this manual. Warranty claims also will be cancelled in case the system casing is opened. 1. Make sure before putting the system into operation, that the fan and the air inlets are clean and not blocked by anything. 2. It must be assured that the system-head can rotate unhindered throughout his complete rotating range. A safety distance of at least 0.5 m to any easily inflammable material (e.g. decoration material) must be adhered. 3. Attention! Don t touch the device during the operation. This can cause injuries or damages. 4. The system doesn t contain any maintainable parts. Don t open it! 5. It is necessary to wait at least 15 minutes after disconnecting the AC before changing the optical carrier. Pay attention to possibly hot parts of the system. -- Danger of BURNING Never look directly into the beam of light or one of the LEDs. Never use optical apertures with a distance less than 0.5 m to observe the beam of light. LED Class 2M. You'll risk a serious injury of your eyes and in particular of your retina. Attention: LED Class 2M can cause injuries of your eyes even without optical instruments in front of them or within a distance of less than 0.5m and short exposure time. Hence: Avoid direct radiation of your eyes! 7. To allow a secure operation, follow also the Installation guide described in chapter 2. Operating the IMPRESSION without suitable safety aids like Safety cables or clamps/hooks can increase the risk of an accident. 8. Repair-, maintenance- and installation work shall be done by qualified or GLP certified staff only. You need to pay attention to the common rules of technology that are not explicit mentioned in this manual. 9. Use only original spare parts. Any structural modification on the system will terminate all warranty claims. GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 5

6 2 Preparation and Installation R-G-B Static 2.1 Mounting The IMPRESSION is fully operational whether it hangs or is mounted to the wall. It can also be operated while standing on the floor. Keep a safety distance of 0.5 m towards any easily inflammable materials (decoration etc.). Pay attention to the regulations of: BGV C1 (former VBG 70) and DIN VDE The installation shall be done by qualified staff only. For the various mounting positions of the IMPRESSION (standing on the floor, sideways or hanging) different accessories kits are available. Through this a safe and firm installation is assured. You'll find special connectors on the bottom side of the system which are put to use here. In addition the front side of the system is marked with (FRONT) as this is important for a even orientation during installation. GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 6

7 1x M10 (length max.16mm) front side of the fixture 2x Camlock quick release fasteners Mounting on the Floor (Upright) To operate the IMPRESSION in an upright position, please use the dedicated tripod which is mounted to the bottom side of the system. It is fixed with fasteners called Camlock quick-release connectors. Turn the two fasteners both 90 to lock them. Do the opposit e to release them again. On both sides you'll find eyelets to pull though a fixing strap. This allows an additional bracing of the system during the upright operation. 2x Ca m loc k 2x eyelets Mounting in hanging Position (Head first) To operate the IMPRESSION in an hanging position, please use a halfcoupler (clamp) which is mounted directly to the bottom side of the system. It is fixed centrically with a M10x16 mm thread bolt. GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 7

8 M10x Mounting in sidewise Position To operate the IMPRESSION in a sidewise position, please use an addition mounting bar. Also this is fixed by two Camlock quick-release connectors. Two half-couplers (clamps) are now used to mount the system to a standard truss bar. This technique is necessary to cope with the torque which accrues in this mounting position. In addition it allows a concentrically position between two truss belts. Never use the "Mounting in hanging Position" technique described above to fasten the system in the sidewise position. A safe and sound installation can not be assured in this way. This can also damage the system base. 2x 90 Half-coupler (clamp) 1 Half-coupler (clamp) 2 GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 8

9 without mounting bar 2.2 Secure the Device Regardless of the mounting method of the IMPRESSION you'll have to use a stipulated safety wire. Therefore you have to pull the safety wire through to two provided holes on the bottom side of the system and connect it with the trusssupport. Pay attention to a safe and proper fastening. Install a safety wire that can hold at least 10 times the weight of the fixture. Never use the carrying handles for this purpose. 2.3 Connections Power Supply ~ Volt AC, Hz, earth contact type plug - Powercon Connected load 350 VA (W) <=> 4 AT (micro-fuse 5x20mm) Please see printing on the case for the right electronic supply! Disconnect from the mains supply for changing the fuse and use only the above described micro-fuse type DMX USITT DMX-512 Standard input/output in 3 pole connectors. 3 pole: Pin 1 = [Ground] / Pin 2 = [-] / Pin 3 = [+] The DMX- Addressing starts at the DMX- Address [001]. GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 9

10 DOWN - UP DOW 3 The Menu Field You ll find the control board on the side part of the arm. It allows you to make all necessary adjustments of the IMPRESSION. With the Mode-key you get into the main menu. Afterwards you can navigate through the menu with the Up/Down-keys. Push the Enter-key to get in the next menu level or to confirm your settings. Make them and set functions ON/OFF with the Up/Down-keys. Confirm and save it with the Enter-key (the display shows OK). Push the Mode-key to cancel the entry and go back to the main menu. Mod e Down Enter Up MODE - ENTER Level1 Level 2 Level 3 Level 4 Remark DMX Start Address 001 Define the DMX start address Special Manual DMX Manual control of all system functions Display Contrast Default Set Set Dimmer Frequency LED Dimmer Version Impression Version Adjust Temperature Arm Temperature Head DMX Hold Special White Temperature Dimmer Shutter Blue Green Red Color Wheel Key code xxxx Clear EEPROM Diagnose Anz Ti0- Int-Err PFC Voltage Activate the White- or Full-Power Mode; see also DMX table Abgleich der Farbtemperatur der Farbe WEIß Manual control for Dimmer Manual control for Shutter Manual control for blue Manual control for green Manual control for red Manual control for the color wheel Adjustment for the Display contrast Resetting all functions to original values Changes PMW frequency between 600Hz and 1200Hz Reads out the current LED dimmer (software) version Reads out the current CPU software version Use the code for entering the calibration menu (for authorized persons only) Erase EEPROM memory Diagnose functions Internal data and function diagnose Show the present PFC voltage Indicates the arm temperature Indicates the head temperature Defines whether the last DMX signal is stored or the lamp is switched OFF in case of signal interruption GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 10

11 White Adjust Set DMX Image DMX input Monitor Red Blue Green Special White Temperature Dimmer Shutter Blue Green Red Color Wheel Adjustments for a uniform white color (white balance); only in white-mode Input for red adjustments Input for blue adjustments Input for green adjustments Stores the Scene currently sent to the unit Indicates the presently received DMX signal per DMX channel Instantaneous value for Special Adjustment of the color temperature for WHITE Instantaneous value for Dimmer Instantaneous value for Shutter Instantaneous value for Blue Instantaneous value for Green Instantaneous value for Red Instantaneous value for Color Mixing unit Self test Performs an automatic self-test Live time Indicates the overall operation time of the system Display Adjust the display Blackout ON/OFF: Display OFF DOWN - UP Select DMX Mode White Mode Compressed Normal High- Resolution Please select the desired DMX Mode Only 8 DMX channels are being used if this Mode is activated 6 DMX channels are being used if this Mode is activated 9 DMX channels are being used if this Mode is activated. Dimmer operates at 16 bit. ON/OFF: Adjustments for white-balance are activated Reset RESET and new calibration for all functions GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 11

12 4 DMX Channel Selection (DMX Protocol) Normal-Mode 8 DMX channels Channel Function Time and Value DMX HEX % 1) Color Colors adjustable via RGB ,5 (fixed) Color 01 - Red 1) F 3..5,5 Color 02 - Amber 1) ,5 Color 03 - Warm Yellow 1) F 9..12,5 Color 04 - Yellow 1) ,5 Color 05 - Green 1) F ,5 Color 06 - Turquoise 1) ,5 Color 07 - Cyan 1) F ,5 Color 08 - Blue 1) ,5 Color 09 - Lavender 1) F ,5 Color 10 - Mauve 1) ,5 Color 11 - Magenta 1) F ,5 Color 12 - Pink 1) ,5 White - CTO Color temperature F ,5 3200K White Color temperature ,5 5600K White - CTB Color temperature F ,5 7200K Rainbow Effect Stop 2) Rainbow Effect 3) slow - fast DF Rainbow Effect, random colors slow - fast E=..FF ) Red Color mixing system - Red 0-100% FF ) Green Color mixing system - Green 0-100% FF ) Blue Color mixing system - Blue 0-100% FF ) Shutter Shutter closed F 0..5,5 Random Pulse effect slow - fast F 6..18,5 Up-dimming then Shutter closing slow - fast F (random patterns) Shutter open then down-dimming slow - fast F (random patterns) Up-dimming then down-dimming slow - fast F (random patterns) Strobe effect pause 5s to 1s A0..C Strobe effect, slow - fast 1 Hz.. 10 Hz C8..EF Shutter open F0..FF ) Dimmer Dimmer 0% - 100% FF ) Color No color temperature correction temperature Continuous color temperature correction between 3200k k Applicable only for White color 5) FF ) Special Max. Power-Mode 4) Max. light output without F 0..5,5 white balance White-Mode 4) White balance used F 6..12,5 Fan min. as long as temp. < 90 C E0..E ,5 RESET (Normal Mode) FA..FF GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 12

13 4) Max. Power-Mode vs. White-Mode The IMPRESSION can regard the white-balance adjustments for each individual color setting. Whether the White-Mode is used with RGB can be selected in the Normal DMX-Mode during operation with the Special DMX channel. If the Special channel is set to a value between DMX 0..15, the White-Mode is not used and the RGB goes for the maximum light output. If the Special channel is set to a value between DMX , the white balance is used for the RGB output. Since there is no Special DMX channel in the Compress DMX-Mode, the possibility exists to likewise select these settings also in the display menu. Is the White-Mode set to ON, the white-balance is activated. If the White-Mode is set to OFF, the RGB goes for the maximum light output (Max. Power- Mode). 5) The continuous color temperature correction is applicable only for the White color i.e. if this function is selected (DMX 001) the Impression will change the color to white immediately and will then be adjustable in the color temperature in a range between 3200K and 7200K. Hence a color correction for others than white is not intended. Compress-Mode 6 DMX channels Channel Function Time and Value DMX HEX % 1) Color Colors adjustable via RGB ,5 (fixed) Color 01 - Red 1) F 3..5,5 Color 02 - Amber 1) ,5 Color 03 - Warm Yellow 1) F 9..12,5 Color 04 - Yellow 1) ,5 Color 05 - Green 1) F ,5 Color 06 - Turquoise 1) ,5 Color 07 - Cyan 1) F ,5 Color 08 - Blue 1) ,5 Color 09 - Lavender 1) F ,5 Color 10 - Mauve 1) ,5 Color 11 - Magenta 1) F ,5 Color 12 - Pink 1) ,5 White - CTO Color temperature F ,5 3200K White Color temperature ,5 5600K White - CTB Color temperature F ,5 7200K Rainbow Effect Stop 2) Rainbow Effect 3) slow - fast DF Rainbow Effect, random colors slow - fast E0..FF ) Red Color mixing system - Red 0-100% FF ) Green Color mixing system - Green 0-100% FF ) Blue Color mixing system - Blue 0-100% FF ) Shutter Shutter closed F 0..5,5 Random Pulse effect slow - fast F 6..18,5 Up-dimming then Shutter closing slow - fast F ,5 (random patterns) Shutter open then down-dimming (random patterns) slow - fast F GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 13

14 Channel Function Time and Value DMX HEX % Up-dimming then down-dimming slow - fast F (random patterns) Strobe effect pause 5s to 1s A0..C Strobe effect, slow - fast 1 Hz.. 10 Hz C8..EF Shutter open F0..F ,5 RESET Min. 3 Sec. 250 FA 98 Shutter open FB..FF ) Dimmer Dimmer (0% - 100%) FF High Resolution (Extended) -Mode 7 DMX Channels Channel Function Time and Value DMX HEX % 1) Redcoarse Color mixing system Red 0-100% FF ) Red-fine Color mixing system Red-Low FF ) Greencoarse Color mixing system Green 0-100% FF ) Greenfine Color mixing system Green-Low FF ) Bluecoarse Color mixing system Blue 0-100% FF ) Blue-fine Color mixing system Blue-Low FF ) Shutter Shutter closed F 0..5,5 Random Pulse effect slow - fast F 6..18,5 Up-dimming then Shutter closing slow - fast F ,5 (random patterns) Shutter open then down-dimming slow - fast F (random patterns) Up-dimming then down-dimming slow - fast F (random patterns) Strobe effect pause 5s to 1s A0..C Strobe effect, slow - fast 1 Hz.. 10 Hz C8..EF Shutter open F0..F ,5 RESET Min. 3 Sec. 250 FA 98 Shutter open FB..FF ) Dimmercoarse Dimmer 0% - 100% FF ) Dimmerfine Dimmer - Low FF ) The predefined colors can be used as start-colors for the Rainbow effect. Please select first a desired start-color before you activate the rainbow effect. All Impressions will afterwards start from that color and will execute the rainbow effect synchronously. Different Impressions can certainly have different start-colors but will still execute the rainbow effect synchronously. If you choose a color different from the once marked with 1) in the tables above the rainbow start-color will be red. 2) Rainbow-effect Stop will pause this function. After resuming the rainbow-effect will be continued with the current color. GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 14

15 3) The Rainbow-effect will run synchronously only if it will be started going out from one of the predefined colors (see also 1) before). Locking and unlocking the Control Panel Please lock and unlock the control panel by pressing the menu keys MODE & ENTER & UP at the same time. Additional features during switching-on the system a) 1200Hz Mode (Hold down the UP- button during power ON) After switching ON the system the LEDs will be operated with a Pulse Width Modulation (PWM) of 1200Hz. In addition all standard setting will be loaded (DMX start address [001], Normal Mode with 14 DMX channels). b) 600Hz Mode (Hold down the DOWN- button during power ON) After switching ON the system the LEDs will be operated with a Pulse Width Modulation (PWM) of 600Hz. In addition all standard setting will be loaded (DMX start address [001], Normal Mode with 14 DMX channels). c) Standard Mode (Hold down the ENTER- button during power ON) After switching ON the system the DMX start address will be set to [001]. All other setting remain unchanged. Additional Display Indications As a default you'll find the following additional information in the first row of the LCD display: XX/X/XX 06 = 600Hz / 12 = 1200Hz N = Normal Mode / C = Compressed Mode / H = High Res. Mode N = Tilt normal / I = Tilt inverted N = Pan normal / I = Pan inverted GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 15

16 4 Maintaining and Cleaning the IMPRESSION The IMPRESSION is a system of very low maintenance. It is only necessary to clean the air in- and outlets as well as the optical LED lenses from time to time. For a safe operation it is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid residues must not built up on or within the fixture. Otherwise the fixture's light-output will be significantly reduced or damages can occur. Regular cleaning will not only ensure the maximum light-output, but will also allow the fixture to operate reliably throughout its life. A soft lint-free cloth moistened with any good glass cleaning fluid is recommended, under no circumstances should alcohol or solvents be used! 4.1 Safety regulations Pull out the main plug! Wait min. 15 minutes after the last operation to cool down the fixture. 4.2 Circumference and Interval (rule-of-thumb) The contamination of the fixture depends on the environment details. Hence no general guidelines can be given. The intervals given below are only suggestions from our practice experience. Position Interval In this way LED reflector and optical system weekly soft brush /lint-free cloth Fan and air channel monthly vacuum cleaner, airbrush, etc. Attention: Never let optical parts come into contact with oil or fat. Before running the fixture wait until all parts are dried up. Never tough lenses with bare fingers. GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 16

17 5 Technical Specifications Power supply Power consumption Power Input Fuse protection Operational Parameters Max. Ambient Temperature Mounting Position R-G-B Static 350 VA (Watt) ~ V AC, Hz (wide range input) Micro-fuse 5x20 mm, T 4A 45 C (integrated overheating switch) Any (see chapter mounting) Lighting System - Additive Color mixing LED Type 90x Luxeon K2 High-power- LEDs Lifetime h 30 LEDs per color, wavelength optimized for maximum presentable color space Optical System High efficient Collimator cluster Exchangeable optical carrier with 10 light distrib ution angle (25 optional) Scattering light aperture Shutter / Dimmer (8 Bit) Strobe- Effect with variable speed between 1-10 flashes per second, Random-Strobe, Pulse- Effects Continuous Dimmer 0-100% DMX Control Standard USITT DMX-512, 3 pole XLR; [+] = Pin 3 [-] = Pin 2 [Ground] = Pin 1. Die DMX- Addressing starts at the DMX channel [001]. Weights and Measures Width of the base Length of the base height (head vertical) Weight (net) 340 mm 145 mm 370 mm 7-8 kg GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 17

18 6 Index B BGV C C Camlock... 7 Circumference Cleaning Compress-Mode... 13, 14 D Danger of BURNING... 5 Description of Device... 4 DIN VDE DMX... 9 DMX Protocol E Enter-key Eyelets... 7 H Half-couplers (clamps)... 8 I Instruction Version... 1 Internet... 1 L LED Class 2M... 5 M Maintenance Max. Power-Mode Menu Field Micro-fuse... 9 Mode-key Mounting... 6 Mounting in hanging Position... 7 Mounting in sidewise Position... 8 Mounting on the Floor... 7 N Normal-Mode O Optical parts P Power Supply... 9 Powercon... 4 S Safety distance... 6 Safety Instructions... 5 Secure the Device... 9 Software Version... 1 T Technical Specifications U Up/Down-keys V VBG W Warranty claims... 5 Weights and Measures White-Mode GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 18

19 GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 19