SPECIFICATION FOR COLOR STN LCD MODULE

Transcription

1 SPECIFICATION FOR COLOR STN LCD MODULE MODEL NO: TM128128A4KFWGWC22 CUSTOMER: TIANMA MICROELETRONIC CO., LTD 22/F HANGDU BUILDING, CATIC ZONE, SHEN NAN ROAD CENTRAL SHENZHEN, CHINA TEL: (86-755) FAX: (86-755) WEB: PREPARED CHECKED VERIFIED BY R&D DEPT VERIFIED BY QC DEPT APPROVED

2 REVISION RECORD Date Rev.No. Revision Items Prepared Checked Approved V1.0 The first version - 2 -

3 CONTENTS Page 1. General Specifications Outline Drawing Circuit Block Diagram Absolute Maximum Ratings Electrical Specifications and Instruction Code Optical Characteristics Reliability Quality level Precautions for Use of LCD Modules

4 1.General Specifications Item Contents Unit Note LCD Type CSTN - Display color 65K 1 LCD Duty 1/128 - LCD Bias 1/12 - Viewing Direction 6:00 O Clock Active Area(W H) mm Number of Dots 128(RGB) 128 mm Dote Size(W H) mm Dot Pitch(W H) mm Controller ST V DD 2.8 V Vop 14 V Outline Dimensions Refer to outline drawing on next page Backlight 1-LED (white) - Operating Temperature -20~+70 - Storage Temperature -30~+80 - Weight TBD g 2 Data Transfer 8 bits parallel - Polarizer Mode Transmissive/negative - Note 1: Color tune is slightly changed by temperature and driving voltage. Note 2: TBD- To Be Determined

5 2. Outline Drawing - 5 -

6 3. Circuit Block Diagram - 6 -

7 4. Absolute Maximum Ratings(Ta=25 ) Item Symbol Min. Max. Unit Note Power Supply Voltage V DD V Power Supply Voltage for LCD Logic Signal Input Voltage Vop - - V V I -0.3 V DD +0.3 V 1,2 Operating Temperature Top Storage Temperature Tst Notes: 1. If the module is above these absolute maximum ratings. It may become permanently damaged. Using the module within the following electrical characteristic conditions are also exceeded, the module will malfunction and cause poor reliability. 2. V DD >V SS must be maintained

8 5. Electrical Specifications and Instruction Code 5.1 Electrical characteristics (Ta=25 ) Parameter Symbol Condition Min Typ Max Unit Note Operation voltage V OP Ta= V 1 Input Voltage H V IH V DD =2.8V 0.8V DD - V DD V L V IL V DD =2.8V Vss - 0.2V DD V Note: Output Voltage Current Consumption H V OH - 0.8V DD - V DD V L V OL - Vss - 0.2V DD V I CC1 1: IC default setting, Duty:1/128. Normal mode 2: Display full white. Backlight on state ma 2-8 -

9 5.2 LED backlight specification Item Symbol Condition Min Typ Max Unit Note Forward voltage V f I f =20mA V Reverse voltage V r I r =15uA - V Forward current Normal I pn 20 1-chip Dimming I pd ma Reverse Current I r V r =?V 15 µa Uniformity I f =20mA

10 5.3 Interface Signals Pin No. Symbol I/O Function 1 NC I Not connected 2 LED+ P +3.3V for backlight 3 LED- P Supply ground for backlight 4 Vg I/O Bias LCD driver supply voltage 5 XV0 I/O Negative LCD driver supply voltage 6 V0 I/O Positve LCD driver supply voltage 7 Vm I/O Bias LCD driver supply voltage 8 VDD P Power Supply Voltage 9 VSS P Ground 10 VDD P Power Supply Voltage 11 EXT I MTP burn-in control pin 12 CS I Chip select: Low active 13 IF2 I 14 IF1 I Parallel data interface select pin 15 RST I Reset pin: Low active 16 RD I Read enable clock input pin 17 VDD P Power Supply Voltage 18 D7 I/O 19 D6 I/O 20 D5 I/O 21 D4 I/O 22 D3 I/O 8 bit data bus 23 D2 I/O 24 D1 I/O 25 D0 I/O 26 WR I Write enable clock input pin 27 A0 I Data / Instruction select input pin 28 VPP I MTP power supply voltage 7.5~7.75V input pin

11 5.4 Interface Timing Chart Note: Please refer to SITRONIX s ST7637 data sheet for more details

12 5.5 Instruction table

13 - 13 -

14 - 14 -

15 6. Optical Characteristics Item Symbol Condition Min. Typ. Max. Unit Note Brightness Bp Φ 1 = Cd/m 2 1 Uniformity Bp Φ 2 =0 80% 1,2 Viewing Angle Contrast Ratio Response Time Φ 1 (up down) Cr 2 Φ 2 (left right) -40~+20-45~+45 Deg 3 Cr Φ 1 =0 Tr Φ 2 = ms T f

16 Note 1: The data are measured after LEDs are turned on for 5 minutes. LCM displays full white. The brightness is the average value of 9 measured spots. Measurement equipment PR-705 (Φ10mm) Note 2: Bp = Bp (Min.) / Bp (Max.) 100 (%) Bp (Max.) = Maximum brightness in 9 measured spots Bp (Min.) = Minimum brightness in 9 measured spots. 3~5mm Measurement equipment PR-705 (Φ10mm) Note 3: Definition of Viewing Angle(Test LCD using DMS501)

17 Note 4: Definition of contrast ratio.( Test LCD using DMS501) Contrast ratio ( Cr) = Brightness Brightness of of selected dots non selected dots Note 5: Definition of Response time(test LCD using DMS501) Operating Voltage: Vop Frame Frequency: 70Hz Appling Waveform: 1/N duty 1/a bias View angle (θ, Φ): (0 0, 0 0 )

18 Note 6: Definition of Color of CIE Coordinate and NTSC Ratio. Color gamut: S = area of area of RGB NTSC triangle triangle 100%

19 7. Reliability No. Test Item Test condition Criterion High Temperature Storage Low Temperature Storage High Temperature Operation Low Temperature Operation High Temperature /Humidity Operation 80 ±2 96H Restore 4H at ±2 96H Restore 4H at ±2 48H Restore 4H at ±2 48H Restore 4H at ±2 90%RH 48H min 30min 1. After testing, cosmetic defects should not happen. 2.Total current consumption should not be over 10% of initial value. 6 Temperature Cycle 25, 5min after 10cycle, Restore 4H at Vibration Test (package state) Shock Test (package state) Atmospheric Pressure Test Cable Bending Test 10Hz~150Hz, 100m/s2, 120min Half- sine wave, 300m/s2, 18ms 25kPa 16H Restore 2H Not allowed cosmetic and electrical defects. More than times

20 8 Quality level 8.1 Notes for quality standard General Definitions of Inspection items Definitions of Inspection ranges Outgoing Inspection standard Note 1. Should any defects which are not specified in this standard happen, additional standard shall be determined by mutual agreement between customer and Tianma. 2. Viewing Area should be the area which Tianma guarantees. 3. Limited sample should be prior to this Inspection standard. 4. Viewing Judgement should be under static pattern. 5. Inspection conditions Inspection distance : 250 mm (from the sample) Temperature : 25±5 Inspection angle : 45degrees in 3,6,9,12 o clock direction Pinhole, Bright spot, The color of a small area is different from the Black spot, White spot, remainder. Black line, White Line, The phenomenon dose not change with voltage. Foreign particle, Bubble Contrast variation Polarizer defect Glass defect X1 X2 The color of a small area is different from the remainder. The phenomenon changes with voltage. Scratch, Dirt, Particle, Bubble on polarizer or between polarizer and glass. Glass crack, Shaved corner of glass, Surplus glass Dividing A zone and B zone proceed to make a judgment. Y2 A zone : Inside Viewing area B zone : Outside Viewing area X1(A.A~V.A): mm Y1 X2(A.A~V.A): mm Y1(A.A~V.A): mm Y2(A.A~V.A): mm Inspection level Ⅱ Normal Inspection Rank Inspection Item AQL(Number of defective LCMs counted) Major All Functional defects(such as No display, Display 0.65 defect abnormally, Open or missing segment, Short circuit, Missing component, No sound, Blight abnormally and so on),outline dimension beyond the drawing, progressive defects and those affecting reliability Minor Appearance defects, such as Black/White spot, 1.50 defect Bright spot, Pinhole, Black/White line, Contrast variation, Bubble(Bubble in the cell is not included),glass defect, Polarizer defect, Soldering defect and so on. Details of the standard as follows

21 8.2Standards of inspection items Inspection item 1 Black spot, White spot b Bright Spot, Pinhole Foreign Particle, Bubble and Particle Φ=(a+b)/2(mm) Between polarizer and glass, Scratch on polarizer 2 Black line, W White line, Bubble and Particle Between L Polarizer and glass, Scratch on W:Width, polarizer L:Length(mm) 3 Contrast variation b 4 Bubble inside cell 5 Polarizer defect (if Polarizer is used) a Φ=(a+b)/2(mm) Scratch and damage on polarizer, Particle on polarizer or between polarizer and glass. Bubble, dent and convex A B C D A B C D A B C D Judgement standard Acceptable number Category A zone B zone Φ <Φ <Φ <Φ Neglecte d Total defective point(b,c) 3 W <W 0.03 L 3.0 Neglected <W 0.05 L <W 0 Total defective point(b,c) 2 Φ 0.2 Neglected 0.2<Φ <Φ <Φ 0 Total defective point(b,c) 3 Neglected Neglected Neglected any size none none Refer to item 1 and item 2. A B C Φ 0.3 Neglected 0.3<Φ <Φ 0 Total defective point(b,c) 2 Neglected 6 Surplus glass 1Stage surplus glass b 0.3mm b 2Surrounding surplus glass Should not influence outline dimension and assembling

22 7 Glass defect crack Inspection item 1 The front of lead terminals Judgment standard Category(application: B zone) A If a t and b 1.0, c is not limited B a t, 1 b 2mm, c 3mm b C If glass crack cover alignment mark, b D b 0.5mm. Crack at two sids of lead terminals w t a c should not cover patterns and alignment mark 2Surrounding crack non-contact side b < Inner borderline of the seal seal c b a t Inner border line of the seal Outer border line of the seal 3 Surrounding crack contact side b < Outer borderline of the seal seal t c b a Inner border line of the seal Outer border line of the seal 4 Corner A a t, b 3.0, c 3.0 *Glass crack should not cover patterns used for a t w c

23 Inspection item Judgement standard 8 PCB defect Component soldering: No cold soldering short open circuit Component burr tin ball The flat encapsulation component position deviation must be less than 1/3 L W/3 W width of the pin (Pic.1); the sheet component deviation: Soldering pad Lead Component Pin deviates from the pad and contact with the near components is not permitted(pic.2) L2>0 L1>0 lead defect: The lead lack must be less than 1/3 of its width; The lead burr must be less than 1/3 of the seam; Impurities connect with the near leads is not permitted Connector soldering: Soldering tin is at contact position of the plug and socket is not permitted No foundation is scald Serious cave distortion on plug and socket contact pin is not permitted head Base Board Soldering tin is not permit in this area Soldering tin is not permit in this area socket Base Board Glue on root of the speaker receiver and motor lead: The insulative coat of the lead must join into the PCB; the protected glue must envelop to the insulative coat. 保护胶 PCB 引线 绝缘胶皮

24 9. Precautions for Use of LCD Modules 9.1 Handling Precautions The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer carefully If the display surface is contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If still not completely clear, moisten cloth with one of the following solvents: Isopropyl alcohol Ethyl alcohol Solvents other than those mentioned above may damage the polarizer. Especially, do not use the following: Water Ketone Aromatic solvents Do not attempt to disassemble the LCD Module If the logic circuit power is off, do not apply the input signals To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment. a. Be sure to ground the body when handling the LCD Modules. b. Tools required for assembly, such as soldering irons, must be properly ground. c. To reduce the amount of static electricity generated, do not conduct assembly and other work under dry conditions

25 d. The LCD Module is coated with a film to protect the display surface. Be care when peeling off this protective film since static electricity may be generated. 9.2 Storage precautions When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps The LCD modules should be stored under the storage temperature range. If the LCD modules will be stored for a long time, the recommend condition is: Temperature : 0 ~ 40 Relatively humidity: 80% The LCD modules should be stored in the room without acid, alkali and harmful gas. 9.3 The LCD modules should be no falling and violent shocking during transportation, and also should avoid excessive press, water, damp and sunshine