SIGNET 5500 Flow Monitor ENGLISH

Size: px
Start display at page:

Download "SIGNET 5500 Flow Monitor ENGLISH"

Transcription

1 ENGLISH H (6/01) English CAUTION! Remove power to unit before wiring input and connections. Follow instructions carefully to avoid personal injury. Contents 1. Power Connections 2. Compatible Sensor Wiring 3. Sensor Pulse Output Connections 4. Auxiliary Pulse Output Connections 5. Totalizer Reset Connections ma Current Output Connections 7. Relay Connections 8. Output Functions 9. Menu Functions 10. Parts and Accessories 11. Specifications 12. Quick Reference Menu Parameters 13. Troubleshooting 14. Maintenance Remove terminal blocks for easy wiring Sen. Pwr. Iso. PLS AUX Std. Sensor Open Collector Sensor LISTED UL 77CJ 1224 V 10 W 1 2 Total reset Patent No. D376,328 Flow 1 2 Sen. Pwr. Iso. PLS AUX Std. Sensor Open Collector Sensor LISTED UL 77CJ 1224 V 10 W 1 2 Total reset Patent No. D376,328 Flow Power Connections 2. Compatible Sensor Wiring CAUTION! Never connect 115 VAC or 230 VAC to rear power terminals. High voltage AC will damage instrument and void warranty. GF SIGNET Sensors: Red 515 Black Shld. = Double Insulated = DC or AC power 1224 V 10 W External power supply VDC OR VAC Std. Sensor Sen. Pwr. Iso. Open Collector Sensor Red Black Shld Vortex* To reduce the possibility of noise interference, isolate AC power lines from signal lines. Maximum 420 ma loop impedance (sec. 6) is affected by the supply voltage. Pg 1 of 12

2 3. Sensor Pulse Output Connections (sec. 8.1) 3.1 GF SIGNET instrument with internal opencollector excitation voltage and pullup resistor. Use 2conductor shielded twistedpair cable for lines up to 30 m (100 ft.) max. Pullup resistor NOT REQUIRED when connected to GF SIGNET instruments. PLS * Shld Red Red Iso. Shld GF SIGNET Instrument *(Opencollector sensor terminals) 3.2 Pulse connection options for instruments without internal opencollector excitation voltage and pullup resistor shown below. NPN sink input PLS 10 kω Input Other instrument 28 VDC max. External power supply PLS 10 kω 28 VDC max. Other Input instrument PNP source input 4. Auxiliary Pulse Output Connections 4.1 Pulse mode (sec. 8.2) External device control The auxiliary can be configured for either TTL, CMOS, or opencollector compatible inputs using the proper pullup resistor and an external power supply. TTL inputs: An external 5 VDC power supply and 10 kω pullup resistor is recommended. CMOS inputs: An external 3 to 15 VDC power supply and 10 kω pullup resistor is recommended. 12 VDC Opencollector inputs: An external 12 VDC power supply and 10 kω pullup resistor is recommended. 24 VDC Opencollector inputs: An external 24 VDC power supply and 10 kω pullup resistor is recommended. Signal Signal ground 10 kω AUX External power supply 3 28 VDC Opencollector transistor, optically isolated, 5 ma max. sink, 28 VDC max. pullup voltage. Programmable pulse width, seconds (sec. 9.2 M) Selectable Active high or active low pulse logic (sec. 9.3 J). Use 2conductor shielded twisted pair cable for AUX lines to 30 m (100 ft) max. 4.2 Totalizer pulse mode (sec. 8.2) External counter or accumulator inputs without internal opencollector excitation voltage and pullup resistor. External power supply AUX 10 kω NPN sink input Input Counter or Accumulator 28 VDC max. External power supply AUX 10 kω 28 VDC max. Counter or Input Accumulator PNP source input pg 2 of 12

3 5. Totalizer Reset Connections (sec. 8.3) Momentary pushbutton switch 1 2 Total reset Use 2conductor shielded twisted pair cable for reset lines up to 30 m (100 ft) max. External reset switch overrides software security feature (section 9.3 I). To reduce the possibility of AC noise interference, isolate AC power lines from reset lines ma Current Output Connections (sec. 8.4) Fuse** 1/8A * 4 20 ma **1/8A fuse recommended (customer supplied) * 420 ma is internally powered (nonisolated), maximum loop impedance 350 Ω with a 12 V instrument supply voltage, 950 Ω with a 24 V instrument supply voltage. 420 ma To isolate and prevent ground loop problems: 1. Use monitor device with isolated inputs, or 2. Use separate DC supply for and monitor device, or 3. Power with12 24 VAC step down transformer 7. Relay Connections Two internal relay contact sets (COM, NO, and NC) may be used for external device control. Front panel LED annunciators indicate the activation status of each relay. Each relay can control up to two devices simultaneously, as shown. Relay operation modes include Low alarm, High alarm, Pulse, and Totalizer (sec. 8.5). Relay 2 NO C NC Relay 1 NO C NC Relay Deenergized NO C NC Relay Energized NO C NC Common device connections include: Pulse mode metering pump control Pulse mode solenoid valve control Low or High mode warning lamps Low or High mode bells or sirens Low or High mode external heavyduty relay External AC/DC power Device A Device B Wiring Example Right Device A IS powered when relay 2 is deenergized (front panel LED "off"). Power is discontinued when the relay 2 setpoint is reached (front panel LED "on"). Device B IS NOT powered when the relay 2 is deenergized. Power is applied after the relay 2 setpoint is reached. Maximum relay contact ratings: 5 30 VDC, VAC, or VAC An external heavyduty relay must be used for devices with surge currents or operating currents that exceed the above specifications. Pg 3 of 12

4 8. Output Functions This section gives a detailed description of all functions. 8.1 Sensor pulse (sec. 3): This emits an opencollector frequency equal to the sensor input. The connects directly to a second GF SIGNET instrument for expanded process control with a single sensor input (sec. 3.1). The is an opencollector type that requires an external pull up resistor and power supply for other instrument inputs (sec. 3.2). 8.2 Auxiliary pulse (sec. 4): The auxiliary can be configured as Low alarm, High alarm, Pulse or Totalizer. Output logic can be selected for either active low (factory default) or active high operation (sec. 9.3 J). The auxiliary is an opencollector type that requires an external pullup resistor and power supply to operate. Refer to diagrams A C below for operation details. LOW alarm mode The is active (relay energized) when the flow drops below the setpoint, and is inactive (relay deenergized) when the flow rises above the setpoint plus hysteresis (sec. 9.2 FG, 9.2 JK). B. HIGH alarm mode The is active (relay energized) when the flow rises above the setpoint and is inactive (relay deengergized) when the flow falls below the setpoint plus hysteresis (sec. 9.2 FG, 9.2 JK). Auxiliary : ideal for external device inputs (sec. 4) Relay s: ideal for external warning lamps, sirens, etc. (sec. 7) Flow Auxiliary : ideal for external device inputs (sec. 4) Relay s: ideal for external warning lamps, sirens, etc. (sec. 7) Low setpoint= Adjustable hysteresis= Output active (relay energized)= Output inactive (relay deenergized)= High setpoint= Adjustable hysteresis= Output active (relay energized)= Output inactive (relay deenergized)= Flow PULSE mode The is active (relay energized) for the programmed pulse width each time the programmed pulse volume is measured by the flow sensor (sec 9.2 HI, 9.2 LM). Auxiliary : ideal for external device control (sec. 4) Relay s: ideal for metering pump or solenoid valve control (sec. 7) = Output active (relay energized) FLOW Flow Sensor volume = Output inactive (relay deenergized) = Programmed pulse volume (e.g Gal.) volume 6 volume 5 volume 4 volume 3 volume 2 volume 1 = Programmed pulse width (relay energize time) Totalizer function The emits an adjustable signal pulse width for each whole engineeing unit measured by the flow sensor (also displayed on totalizer). To enable the totalizer function, the operator must set the relay or auxiliary pulse volume setpoint to (sec. 9.2 H, 9.2 L). Totalizer function: ideal for external counter or accumulator use (sec 4.2) adjustable pulse width VIEW menu totalizer display = Totalizer reset (sec. 5): This feature allows the operator to reset the totalizer with a dry switch contact closure at any time. The external reset switch overrides software security feature (sec. 5) ma (sec. 6): The 420 ma is internally powered by the instrument. 4 ma and 20 ma setpoints are fully adjustable within the programmed flow range (sec. 11 B). The can also be reverse spanned. 8.5 Relay 1 and 2 s (sec 7): Relay s 1 and 2 can be independently configured as Low alarm, High alarm, Pulse or Totalizer. Refer to diagrams A C above for operation details. pg 4 of 12

5 9. Menu Functions To access either CALIBRATE or OPTIONS menus, press and hold the ENTER key as illustrated below: CALIBRATE (sec. 9.2) OPTIONS (sec. 9.3) Press & hold ENTER key for menu ENTER access: VIEW (sec. 9.1) 2 seconds 5 seconds Menus: VIEW menu (sec. 9.1): The VIEW menu is displayed during standard operation. The operator can navigate freely through the menu by pressing either UP or DOWN arrow keys. The VIEW menu also offers a resettable totalizer feature that allows the operator to reset the displayed total at the press of a button. CALIBRATE Menu (sec. 9.2): The CALIBRATE menu contains all critical display setup and parameters. A simple security code feature prevents unauthorized tampering. The operator is required to enter a simple access code for menu access. The same code also unlocks OPTIONS menus. OPTIONS Menu (sec. 9.3): The OPTIONS menu contains setup and display features that are seldom accessed for minor display or adjustments. 9.1 VIEW Menu H B. D. E. F. G Choose: Change: Save: Flow & resettable total Permanent total Loop Range Relay 1 Relay 2 Aux OR OPTIONS = (sec. 9.3I) OPTIONS = To reset total press: ENTER B. B. To exit without changes: quick press Press keys in sequence, (display shows: ) To reset total press: (sec. 9.3I) ENTER Menu Displays A H: (Factory default displays shown in menu column 1) Flowrate and resettable total display: can be reset by the front panel keypad or by remote reset switch (sec. 5). A simple access code feature prevents accidental total reset, when enabled (sec. 9.3 I). External reset switch inputs override security feature, when enabled. B. Permanent total display: records volumetric flow total for the life of the product and is nonresettable. Loop display: shows the current level at the rear terminals. D. Flow Range display: shows the programmed min and max meter range (sec. 9.2 B) E. Relay 1 display: this display shows the programmed operation mode and setpoint for relay 1 (sec. 9.2 FI) F. Relay 2 display: this display shows the programmed operation mode and setpoint for relay 2 (sec. 9.2 FI). G. Aux display: this display shows the programmed operation mode and setpoint for the auxiliary (sec. 9.2 JM). H. Last calibration: this display shows a user defined setup date for maintenance records. This feature is not an internal timer or calender. H. Last calibration A Pg 5 of 12

6 9.2 CALIBRATE Menu N B. Flow units Press keys in sequence will appear during code entry. Unit timebase: h,m,s,d to enter menu, Choose: Change: Save: Menu Settings A N: (Factory default displays shown in menu column 1) Sets flow units label (gpm) and timebase (gpm). Flow units label: Aa Zz, 0 9, / Timebase options: h=hours, m=minutes, s=seconds, d=days (timebase entry affects flow rate display and 4 to 20 ma ) B. Sets Min Max meter and dial range, to (does not affect 4 to 20 ma ) Flow range Meter Min Max Sets flow KFactor: to (see technical notes below) D. Flow KFactor KFactor D. Sets 8digit totalizer units label: Aa Zz, 0 9, / (does not affect totalizer display or s) E. Total units Display label only E. Sets totalizer KFactor: to (see techical notes below) Total KFactor KFactor Relay Low or High Mode Selected Menu items F I repeat for relay 2 setup. F. Sets relay operation mode Low or High, and flow rate setpoint, (sec. 8.5) F. Relay Mode & setpoint G. Sets relay hysteresis, (sec. 8.5) (Set to zero to disable hysteresis feature) G. H. Relay Relay Hysteresis setting Relay Pulse Mode Selected, step F Mode & setpoint ENTER "SAVING" briefly displays H. Sets relay pulse volume setpoint, (sec. 8.5). Set to to enable totalizer function (sec. 8.5). I. Sets relay pulse width, seconds (sec. 8.5) I. Relay Pulse width J. Sets auxiliary mode Low or High, and flow rate setpoint, (sec. 8.2). Aux Output Low or High Mode Selected J. K. Sets auxiliary hysteresis, (Set to zero to disable hysteresis feature) Aux Mode & setpoint K. Aux Hysteresis L. Sets auxiliary pulse volume setpoint, (sec. 8.2). Set to (factory default) to enable totalizer function (sec. 8.2). Aux Output Pulse mode selected, step J M. Sets auxiliary pulse width, seconds L. Aux Mode & setpoint N. Sets user defined setup date for maintenance records. This feature is not an internal timer or calender M. N. To return to VIEW menu: pg 6 of 12 Aux Last calibration A quick press Pulse width Setup date To restore original value: quick press The flow and total KFactors are independent of each other. The KFactor settings represent the number of pulses generated by the GF SIGNET flow sensor for each engineering unit of fluid measured (published in flow sensor manual).

7 9.3 OPTIONS Menu J 1 Choose: Press keys in sequence will appear during code entry. 2 Change: to enter menu, 3 Save: Menu Settings A J: (Factory default displays shown in menu column 1) Selects LCD display contrast: 5 levels B. Selects flow display decimal: *****. to **. *** B. Display contrast Low High Selects totalizer display decimal: ********. to ******. ** Flow display Total display Decimal Total decimal D. Selects LCD display averaging: Off = 0 seconds, Low= 4 seconds, High= 8 seconds (also effects 4 20 ma ) D. Display averaging 0s 4s 8s E. Sets 4 ma setpoint. 4 ma and 20 ma setpoints are reversible. E. F. Loop Loop 4 ma setpoint 20 ma setpoint ENTER "SAVING" briefly displays F. Sets 20 ma setpoint. 20 ma and 4 ma setpoints are reversible. G. Sets 4 ma current : 3.0 to 5.0 ma (overrides 4.00 ma factory calibration) G. H. Sets 20 ma current : 19 to 21 ma (overrides ma factory calibration) Loop 4 ma adjust H. I. Loop Totalalizer reset 20 ma adjust VIEW menu= VIEW menu= I. Selects totalizer reset options: Lock "Off" disables the VIEW menu access code feature; Lock "On" enables the feature (sec. 9.1 A). When enabled, the operator must enter an access code for totalizer reset privileges. The totalizer will be reset in either case if a contact closure is detected at rear reset terminals (sec. 5). J. To return to VIEW menu: Auxiliary out logic A quick press Active Low or High To restore original value: quick press J. Selects Auxiliary logic: Active Low logic (factory default): Output changes from high to low when active, see diagram below. Active high logic: Output changes from low to high when active, see diagram below. Active Low Logic (factory default) Inactive (Off) Active (On) Active High Logic Active (On) Inactive (Off) Pg 7 of 12

8 10. Parts and Accessories Splashproof rear cover # (code ) 5 x 5 inch adapter plate for GF SIGNET retrofit # (code ) Optional surface mount bracket # (code ) Power supply, 115 VAC 24 VAC, # Front snapon bezel, # (code ) Assorted flow unit/multiplier decals, #3.611 (code ) instruction sheet # (code ) 11. Specifications General Sensor compatibility: Accuracy: Input: All GF SIGNET flow sensors ±0.5% of reading Optically isolated Electrical Power: 12 to 24 VDC or 12 to 24 VAC, unregulated, 5060 Hz, 10 W max. Enclosure: Rating: NEMA 4X/IP65 front Dimensions: 1/4 DIN, 96 x 96 x 88 mm (3.8 x 3.8 x 3.5 in.) Case materials: ABS plastic Keypad material: Sealed 4key silicone rubber Weight: Approximately 500 g (18 oz.) Display: Type: Microprocessor controlled aircore meter movement and backlit alphanumeric 2 x 16 LCD Update rate: Flow = 1s, totalizer = <200 ms Contrast: User selected, 5 levels Relay annunciators: 2 LEDs Relay contacts (2 sets): Mechanical SPDT contacts Maximum voltage rating: 5 30 VDC, VAC, or VAC, (power factor = 1.0) Hysteresis: User adjustable Current : 4 to 20 ma, nonisolated, internally powered, fully adjustable and reversible Update rate: < 200 ms Max loop impedance: 350 Ω max with a 12 V instrument supply voltage, 950 Ω max with a 24 V instrument supply voltage Accuracy: ±0.1% of max range Totalizers: 8digit resettable with security option 8digit nonresettable Environmental Operating temp.: Storage temp.: Relative humidity: Altitude: Pollution degree: 2 10 to 55 C (14 to 131 F), 50 C (122 F) max. with optional rear cover 15 to 80 C (5 to 176 F) 0 to 95%, noncondensing 4000 m max. Sensor (PLS) Auxiliary (AUX) pulse s: Opencollector transistor, optically isolated, 5 ma max. sink, 28 VDC max. pullup voltage, programmable (AUX) pulse width rear PLS/AUX terminals GND Internal PLS/AUX circuits Totalizer reset: Front keypad or external contact closure, 30 m (100 ft) max. cable length External contact closure overrides security feature (sec. 5) Agency Approvals CSA, CE, UL listed Manufactured under ISO 9001 Noise immunity: Noise emissions: Safety: EN EN55011 EN pg 8 of 12

9 Dimensions 96 mm (3.8 in.) Panel Gasket Optional Splashproof Rear Cover Front View RELAY GPM RELAY 2 96 mm (3.8 in.) 91 mm (3.6 in.) Mounting Panel Mounting Clamp (2 ea.) 88 mm (3.5 in.) SIDE VIEW ENTER GF SIGNET 76 mm (3 in.) 96 mm (3.8 in.) 88 mm (3.5 in.) 88 mm (3.5 in.) Rear View Std. Sensor UL LISTED 77CJ GF SIGNET Model #3 Sen. Pwr. Iso. Open Collector Sensor 1224 V 10 W 1 2 PLS AUX NO Relay 2 C Total reset NC NO 420 ma Relay 1 C NC Patent No. D376,328 Flow 88 mm (3.5 in.) 92 x 92 mm (3.62 x 3.62 in.) Panel cutout 12. Quick Reference Menu Parameters VIEW Menu Setup Parameters (sec. 9.1) Menu Parameters Display Description Range Factory Default Flow rate and units Resettable total GPM B. Permanent total Current loop 3 21 ma n/a D. Min Max meter and dial range E. Relay 1 mode Relay 1 setpoint Low or High, Pulse, Low GPM F. Relay 2 mode Relay 2 setpoint Low or High, Pulse, High GPM G. Aux mode Aux setpoint Low or High, Pulse, Pulse Gallons H. Last calibration date to Pg 9 of 12

10 CALIBRATE Menu Setup Parameters (sec. 9.2) Menu Parameters Display Description Range Factory Default B. flow unit= digits 13 flow timebase= digits 4 Min max range Aa Zz, 0 9, /, _; Mm, Ss, Hh, Dd _GPM GPM _ = blank display digit option Flow KFactor D. E. Total units Total KFactor Aa Zz, 0 9, /, _ (8digits max.) _Gallons _ = blank display digit option F. G. H. Relay 1 mode Relay 1 setpoint Relay 1 Hysteresis Hysteresis volume Relay 1 mode Relay 1 pulse volume Low or High Pulse Low GPM GPM Gallons Relay mode and setpoint displays repeat for relay 2 setup I. Relay 1 pulse width seconds 10.0 seconds J. Aux mode Aux setpoint Low or High Low K. Aux hysteresis volume L. Aux mode Aux setpoint Pulse Gallons M. Aux pulse width seconds 0.10 seconds N. Last calibration date to OPTIONS Menu Setup Parameters (sec. 9.3) Menu Parameters Display Description Range Factory Default Display contrast 0 to 5 3 B. Flow decimal **.*** to *****. ****.* Totalizer decimal ******.** to ********. *******.* D. Display averaging Off= 0 sec., Low= 4sec., High= 8 sec. Off E. 4 ma setpoint Unlimited GPM pg 10 of 12

11 OPTIONS Menu Setup Parameters Continued... Menu Parameters Display Description Range Factory Default F. 20 ma setpoint Unlimited GPM G. 4 ma adjust 3.0 to 5.0 ma 4.00 ma H. 20 ma adjust 19 to 21 ma ma I. VIEW menu total reset access code On or Off Off J. Auxiliary (AUX) pulse logic Active Low or Active High Low 13. Troubleshooting Display Problem Solution Display timebase too large Change flow timebase (S=Seconds, M=Minutes, H=Hours, D=Days) in CALIBRATE menu to a smaller value (e.g. GPD to GPM) Check settings Relay 1 pulse width too large Reduce Relay 1 pulse width setting (sec. 9.2 I) or increase pulse volume for Relay 1 for frequency input or pulse setting (sec. 9.2 H) volume too small Check settings Relay 2 pulse width too large Reduce Relay 2 pulse width setting (sec. 9.2 I) or increase pulse volume for Relay 2 for frequency input or pulse setting (sec. 9.2 H) volume too small Check settings Auxiliary pulse width too Reduce auxiliary pulse width setting (sec. 9.2 M) or increase pulse for AUX large for frequency input or pulse volume setting (sec. 9.2 L). volume too small Must be between Relay 1, Relay 2, or Auxiliary Enter volumetric setpoint within engineering units (AUX) pulse volume setpoint must be (sec. 9.2 H or 9.2 L) within Must be between Relay 1, Relay 2, or Auxiliary Enter pulse width within seconds (sec. 9.2 I or 9.2 M) (AUX) pulse width must be within seconds Flow KFactor Flow display KFactor cannot be Enter KFactor greater than zero (sec. 9.2 C) can not be zero zero Total KFactor Totalizer KFactor cannot be Enter KFactor greater than zero (sec. 9.2 E) can not be zero zero SETUP READ ERROR Power fault occurred while saving Press any key to reload factory defaults then reprogram flow system setup Press any Key setup menu entry parameters. Note: totalizer displays remain undistrubed and will resume after instrument reset. 14. Maintenance Clean the instrument case and front panel with a soft cloth and mild liquid soap solution. Pg 11 of 12

12 SIGNET Signet Scientific Company, 3401 Aerojet Avenue, El Monte, CA U.S. Tel. (626) Fax (626) For Worldwide Sales and Service, visit our website: Or call (in the U.S.): (800) GEORGE FISCHER Piping Systems (H6/01) English Signet Scientific Company 2001 Printed in U.S. on recycled paper pg 12 of 12

+GF+ SIGNET 8860 Dual Channel Conductivity/Resistivity Controller

+GF+ SIGNET 8860 Dual Channel Conductivity/Resistivity Controller OUTPUT OPTION RELAY 3,4 OPEN COLL 3,4 TEMP 1 SGNL 1 TEMP 2 SGNL 2 - OPEN COLL 4 Æ L ENGLISH 3-8860.090 A-7/00 English CAUTION! Remove power to unit before wiring input and output connections. Follow instructions

More information

Panel cutout required: 1.772" x 3.622" (45mm x 92mm) 1.76" (45mm) 2.45" (62mm) 3.20" (81mm) 3.60" (91mm) 0.59" (15mm) Special Features

Panel cutout required: 1.772 x 3.622 (45mm x 92mm) 1.76 (45mm) 2.45 (62mm) 3.20 (81mm) 3.60 (91mm) 0.59 (15mm) Special Features NEMA4X, IP65 Front Bezel Meter with Relays Option RELAY2 RELAY1 24V OUT POWER 4 3 2 1 6 5 2 1 2 1 NO NC COM NO NC COM RTD TC P P RTD 3 4 1 2 5 TC 6 SWITCH Rear View Gasket APM765 Panel Meter Description

More information

Signet 2250 Hydrostatic Level Sensor

Signet 2250 Hydrostatic Level Sensor Signet 2250 Hydrostatic Sensor *32250.090* 32250.090 Rev. A 10/06 English English Safety Instructions 1. Prior to installation or removal: Depressurize and vent system Drain below sensor level 2. Confi

More information

Signet Chlorine Transmitter

Signet Chlorine Transmitter Signet 8630-3 Chlorine Transmitter English 3-8630.090-3 Rev. D 08/10 English Caution! Remove power to unit before wiring input or output connections. Follow instructions carefully to avoid personal injury

More information

Veeder-Root brand Series C628 Dual Preset Counter (C628-8XXX) Technical Manual

Veeder-Root brand Series C628 Dual Preset Counter (C628-8XXX) Technical Manual Introduction Your Veeder-Root brand C628 Dual Preset Counter is one model in a family of 1/8 DIN units which offers breakthrough display technology as well as easy-to-program single-line parameters. Designed

More information

Multifunction Digital Timer

Multifunction Digital Timer Multifunction Digital Timer 72 x72 mm Timer with Easy-to-use Functions Nine output modes accommodate a wide variety of applications. All parameters set by scroll-through menus accessed from the front panel.

More information

02/11/2015

02/11/2015 24 x 48 Totalizers CTR24 non-backlit model Part number 87622062 Display : 8-digit LCD, height 8 mm Powered by a lithium battery Counter inputs : solid state (4-30 VDC) or voltage (10 260 VAC) Reset on

More information

Installation and User Guide 458/CTR8 8-Channel Ballast Controller Module

Installation and User Guide 458/CTR8 8-Channel Ballast Controller Module Installation and User Guide 458/CTR8 8-Channel Ballast Controller Module Helvar Data is subject to change without notice. www.helvar.com i Contents Section Page Introduction 1 Installation 2 1. Attach

More information

TABLE OF CONTENTS SPECIFICATIONS...1 MOUNTING...3 WIRING...4 THEORY OF OPERATION...6 MILIVOLT INPUT OPTION JUMPER SELECTIONS...7

TABLE OF CONTENTS SPECIFICATIONS...1 MOUNTING...3 WIRING...4 THEORY OF OPERATION...6 MILIVOLT INPUT OPTION JUMPER SELECTIONS...7 TABLE OF CONTENTS SPECIFICATIONS...1 MOUNTING...3 WIRING...4 THEORY OF OPERATION...6 MILIVOLT INPUT OPTION JUMPER SELECTIONS...7 FRONT PANEL OPERATIONS...8 PROGRAMMING FLOW CHART...8 DEFINITIONS OF MENU

More information

Operating instructions Electronic preset counter Type series 717

Operating instructions Electronic preset counter Type series 717 Operating instructions Electronic preset counter Type series 717 1. Description 5.98.3_gb 6-digit adding/subtracting counter with two presets Very bright 8mm high LED display Counting and preset range

More information

Vorne Industries. 87/719 Analog Input Module User's Manual Industrial Drive Itasca, IL (630) Telefax (630)

Vorne Industries. 87/719 Analog Input Module User's Manual Industrial Drive Itasca, IL (630) Telefax (630) Vorne Industries 87/719 Analog Input Module User's Manual 1445 Industrial Drive Itasca, IL 60143-1849 (630) 875-3600 Telefax (630) 875-3609 . 3 Chapter 1 Introduction... 1.1 Accessing Wiring Connections

More information

SCALE & WEIGHT DISPLAYS

SCALE & WEIGHT DISPLAYS The MICRO SERIES SCALE & WEIGHT DISPLAYS LARGE DIGIT MODELS Mighty-5S DPM MODELS Micro-S & Mighty-1S Mighty-1S Micro-S ELECTRO-NUMERICS, INC. Introduction The Electro-Numerics family of Digital Panel Meters

More information

EA402 SERIES ANALOG INPUT FLOW RATEMETER/TOTALIZER INSTALLATION & OPERATING INSTRUCTIONS West Stetson Avenue Hemet, CA USA

EA402 SERIES ANALOG INPUT FLOW RATEMETER/TOTALIZER INSTALLATION & OPERATING INSTRUCTIONS West Stetson Avenue Hemet, CA USA EA402 SERIES ANALOG INPUT FLOW RATEMETER/TOTALIZER INSTALLATION & OPERATING INSTRUCTIONS 3255 West Stetson Avenue Hemet, CA 92545-7799 USA Lit# 24508-68 99775 Rev. 1.1 02/25/05 Tel: 951-652-6811 Fax: 951-652-3078

More information

Figure 1: Standard 906 Sensor and Pulser Disc. Figure 2: Standard 906 Sensor and Pulser Wrap

Figure 1: Standard 906 Sensor and Pulser Disc. Figure 2: Standard 906 Sensor and Pulser Wrap Description: The TR5000 is a Full Logic Control Process ratemeter that can display up to three separate values of rate and compare them to programmable set points. Rates A & B can be programmed by the

More information

Solid-State Digital Timer

Solid-State Digital Timer Solid-State Digital Timer 1/16 DIN, Digital-Set Timer with 0.1 Second to 9,990 Hours Range 8 field-selectable operation modes Universal AC/DC supply voltage timers available Operations include ON-delay,

More information

263 Series LED Bargraph Indicator and Controllers

263 Series LED Bargraph Indicator and Controllers 263 Series LED Bargraph Process Control Water Treatment High resolution 51 segment LED Bargraph for easy reading Accuracy 1% Red display Vertical or Horizontal mounting & stackable Connection Diagrams

More information

GRT SERIES INSTALLATION & OPERATING INSTRUCTIONS

GRT SERIES INSTALLATION & OPERATING INSTRUCTIONS GRT SERIES INSTALLATION & OPERATING INSTRUCTIONS 99880 05/14/03 ! SAFETY INSTRUCTIONS The following instructions must be observed. This instrument was designed and is checked in accordance with regulations

More information

Description. Specifications and Ordering Information 1900/27 Vibration Monitor

Description. Specifications and Ordering Information 1900/27 Vibration Monitor R Specifications and Ordering Information 1900/27 Vibration Monitor Description The 1900/27 is a single-channel, stand-alone, locally mounted vibration monitor. It can be used as a stand-alone machinery

More information

Multifunction devices

Multifunction devices devices devices devices, electronic Type Page LED multifunction displays pulse, frequency, time (DC) Codix 524 240 pulse, frequency, time (AC+DC) Codix 544 243 LCD multifunction preset counters 1 or 2

More information

AK-PVE4 Operating Instructions. Measuring of norm signals in wall-type units. Performance:

AK-PVE4 Operating Instructions. Measuring of norm signals in wall-type units. Performance: AK-PVE4 Operating Instructions Measuring of norm signals in wall-type units 1 2 P Performance: Digit heights: 20 mm Colour: red Display range: -999 9999 Wall-type housing: light grey made of ABS-plastic

More information

Model IQ4-PC User Manual Revision Date:

Model IQ4-PC User Manual Revision Date: Basic Specifications Supply Volts 230V 50/60Hz ±15% 115V 50/60Hz ±15% 24V DC (isolated) ±15% Power Consumption Max. 3VA (IQ4-PC-R0) Max. 6VA (IQ4-PC-R2-PSI24-RT) Operating Temperature -5 ~ +60 C Operating

More information

UNIVERSAL DIGITAL METER DC Volts and Amps AC RMS Volts and Amps Thermocouples and RTDs Process Signals Strain Gauge and Load Cell

UNIVERSAL DIGITAL METER DC Volts and Amps AC RMS Volts and Amps Thermocouples and RTDs Process Signals Strain Gauge and Load Cell 99 Washington Street Melrose, MA 02176 Fax 781-665-0780 TestEquipmentDepot.com UNIVERSAL DIGITAL METER DC Volts and Amps AC RMS Volts and Amps Thermocouples and RTDs Process Signals Strain Gauge and Load

More information

Modular Lube Lubrication Systems System Controls

Modular Lube Lubrication Systems System Controls Model 84501 Program Timer Solid State Designed to control the lubrication cycle frequency of air-operated single-stroke pumps. Timer turns pump on/off at programmed intervals via a 3-way or 4-way air solenoid

More information

STD-525T PRECISION TIMER

STD-525T PRECISION TIMER FN:STD525TM1.DOC STD-525T PRECISION TIMER DESCRIPTION The STD-525T Precision Timer measures and displays accurate elapsed time in minutes, seconds, tenths of seconds, and hundredths of seconds (MM.SS.TH)

More information

Hour Meters / Timers, electronic

Hour Meters / Timers, electronic Hour Meters / Timers, electronic LED Timers Codix 523 For use as a timer, hour meter or short-time meter Pulse width measurement (operating time) Time interval measurement (start/stop) DC 000000 0... 30V

More information

LAUREL ELECTRONICS, INC.

LAUREL ELECTRONICS, INC. LAUREL ELECTRONICS, INC. Laureate Digital Panel Meter for Process, Strain & Potentiometer Follower Signals Features Selectable ±0.2, ±2, ±20, ±200, ±300 & ±600 Vdc voltage ranges Selectable ±2, ±20, ±200

More information

DCP100 Digital Control Programmer Specifications

DCP100 Digital Control Programmer Specifications DCP100 Digital Control Programmer Specifications EN01-6028 October 1996 Overview The DCP100 is a microprocessor based 1 /4 DIN programmer/controller for process variable versus time control of temperature,

More information

EasyReader Model ER2C

EasyReader Model ER2C London Electronics Limited Thorncote Road, Near Sandy, Bedfordshire SG19 1PU Tel +44(0)1767 626444 Fax +44(0)1767 626446 www.london-electronics.com help@london-electronics.com Large display pulse input

More information

6-DIGIT FREQUENCY METER, TACHOMETER, RATE METER, TIMER, PULSE TOTALIZER, PROCESS METER & TOTALIZER WITH RS-232 PENTA P6000

6-DIGIT FREQUENCY METER, TACHOMETER, RATE METER, TIMER, PULSE TOTALIZER, PROCESS METER & TOTALIZER WITH RS-232 PENTA P6000 6-DIGIT FREQUENCY METER, TACHOMETER, RATE METER, TIMER, PULSE TOTALIZER, PROCESS METER & TOTALIZER WITH RS-232 PENTA P6000 NEWPORT PRODUCT INFO MANUAL (HTML) - (PDF Version) P6000A/P5000 - INPUT OPTIONS

More information

COMPANY. MX 9000 Process Monitor. Installation, Operating & Maintenance Manual AW-Lake Company. All rights reserved. Doc ID:MXMAN082416

COMPANY. MX 9000 Process Monitor. Installation, Operating & Maintenance Manual AW-Lake Company. All rights reserved. Doc ID:MXMAN082416 COMPANY MX 9000 Process Monitor Installation, Operating & Maintenance Manual 2016 AW-Lake Company. All rights reserved. Doc ID:MXMAN082416 1 Table of Contents Unpacking...3 Quick Guide...3 Connect to Sensor...3

More information

Signet 8860 Dual Channel Conductivity/Resistivity Controller

Signet 8860 Dual Channel Conductivity/Resistivity Controller OUTPUT OPTION RELAY 3,4 OPEN COLL 3,4 SHLD ISO GND TEMP 1 SGNL 1 SHLD ISO GND TEMP 2 SGNL 2 OPEN COLL 4 L N Signet 8860 Dual Channel Conductivity/Resistivity Controller *38860.090* 38860.090 Rev. G 11/12

More information

Weekly Timer. Mounting track 50 cm (1.64 ft) length PFP-50N 1 m (3.28 ft) length PFP-100N

Weekly Timer. Mounting track 50 cm (1.64 ft) length PFP-50N 1 m (3.28 ft) length PFP-100N Weekly Timer 1/4 DIN Size Timer Features Prompted Programming and Large LCD Display 24 hours x 7 days programming using just 5 switches 16 program steps and cycle operation Two independent 15 A control

More information

LOW-COST, 3 1/2 DIGIT DC VOLTMETERS MODEL 201A & 201AN OPTION 201AN-AC / 301AN

LOW-COST, 3 1/2 DIGIT DC VOLTMETERS MODEL 201A & 201AN OPTION 201AN-AC / 301AN LOW-COST, 3 1/2 DIGIT DC VOLTMETERS MODEL 201A & 201AN OPTION 201AN-AC / 301AN STANDARD FEATURES ±1,999-count display span ±200 mv to ±200 Vdc ranges True-differential input with 80 db CMR 3-wire ratio

More information

1.5mm amplitude at 10 to 55Hz frequency in each X, Y, Z direction for 2 hours 500m/s² (approx. 50G) in each X, Y, Z direction for 3 times

1.5mm amplitude at 10 to 55Hz frequency in each X, Y, Z direction for 2 hours 500m/s² (approx. 50G) in each X, Y, Z direction for 3 times Color Mark Color Mark Feature Outstanding color matching accuracy - RGB light emitting diodes and 12-bit resolution - 2 detection modes (color only / color + intensity) - -step sensitivity adjustment for

More information

Standard signal metering in wall-mounting case

Standard signal metering in wall-mounting case User manual AKV-2VR4C Standard signal metering in wall-mounting case Technical features: Digit height: 20 mm Colour: red Range of display: -999 9999 Wall-mounting case: black, made of ABS-plastic Protection

More information

Digital Input Modules for Compact FieldPoint

Digital Input Modules for Compact FieldPoint Digital Modules for Compact FieldPoint NI cfp-di-300, NI cfp-di-301, NI cfp-di-304, NI 8-,16-, or 32-channel inputs 24 VDC inputs 4 to 250 VDC inputs 15 to 250 VAC inputs (50/60 Hz AC) 3 to 250 VAC inputs

More information

1900/25 Vibration Monitor

1900/25 Vibration Monitor 1900/25 Vibration Monitor BENTLY NEVADA MADE IN USA VIBRATION MONITOR OK ALERT DANGER BYPASS DISPLAY MOD E RESET NORMAL ALERT ALERT ADJUST LEVEL DANGER DANGER LEVEL ADJUST BUFFER ED TRANSDUCER 1 IN/SEC

More information

UDC100 Universal Digital Controller. Specification. Overview. Features. Features, continued /99 Page 1 of 4

UDC100 Universal Digital Controller. Specification. Overview. Features. Features, continued /99 Page 1 of 4 UDC100 Universal Digital Controller 51-52-03-29 11/99 Page 1 of 4 Specification Overview The UDC100 Universal Digital Controller is a microprocessor-based 1/4 DIN low cost temperature controller. It combines

More information

FIELD MOUNTED RATE TOTALISER MODEL 202D

FIELD MOUNTED RATE TOTALISER MODEL 202D FIELD MOUNTED RATE TOTALISER MODEL 202D 16 June 2003 Introduction 1 1. INTRODUCTION The Model 202Di Rate Totaliser is a microprocessor based instrument which accepts a frequency or pulse input from

More information

MG-XV operating instruction. Measuring of norm signals, 4-8-digit. Panel instrument type MG-BV Construction instrument type MG-AV

MG-XV operating instruction. Measuring of norm signals, 4-8-digit. Panel instrument type MG-BV Construction instrument type MG-AV MG-XV operating instruction Measuring of norm signals, 4-8-digit Panel instrument type MG-BV Construction instrument type MG-AV Contents 1. Brief description... 3 2. Safety instructions... 3 2.1. Proper

More information

THE ASTRO LINE SERIES GEMINI 5200 INSTRUCTION MANUAL

THE ASTRO LINE SERIES GEMINI 5200 INSTRUCTION MANUAL THE ASTRO LINE SERIES GEMINI 5200 INSTRUCTION MANUAL INTRODUCTION The Gemini 5200 is another unit in a multi-purpose series of industrial control products that are field-programmable to solve multiple

More information

Self--powered Time Counter

Self--powered Time Counter Self--powered Time Counter Subminiature Time Counters With Enhanced Appearance and Features Large display with 8.6 mm (0.338 in) height Available with backlit LCD PNP/NPN DC voltage available Sevendigits,timerange0to

More information

Operating Instructions (ed. 5.97) Electronic Preset Counter Type Series 904

Operating Instructions (ed. 5.97) Electronic Preset Counter Type Series 904 Operating Instructions 3.96.3 (ed. 5.97) Electronic Preset Counter Type Series 904 1. Description 6 digit preset counter, 2 presets, add./subtr. bright 2-line LCD display with symbols for activated outputs

More information

48x24. Options ORDER NUMBER OF TYPE PFL B

48x24. Options ORDER NUMBER OF TYPE PFL B Frequency metering (0.01 Hz 9999 Hz) with 2 setpoints Free scalable indication and setpoints from 0 up to +9999 Standard: min/max memory - option: analogue output Allow to be placed side by side in grid

More information

EasyReader Model ER4C

EasyReader Model ER4C London Electronics Limited Thorncote Road, Near Sandy, Bedfordshire SG19 1PU Tel +44(0)1767 626444 Fax +44(0)1767 626446 www.london-electronics.com help@london-electronics.com Large display pulse input

More information

K3NX Process Meter OPERATION MANUAL

K3NX Process Meter OPERATION MANUAL Cat.No. N90 E1 1 K3NX Process Meter OPERATION MANUAL K3NX Process Meter Operation Manual Produced January 1998 Notice: OMRON products are manufactured for use according to proper procedures by a qualified

More information

We put you first. And keep you ahead. USES FEATURES. Bulletin SS09040 Issue/Rev. 0.2 (10/14)

We put you first. And keep you ahead. USES FEATURES. Bulletin SS09040 Issue/Rev. 0.2 (10/14) SPECIFICATIONS / INSTALLATION / OPERATION MEASUREMENT SOLUTIONS MMRT Bulletin SS09040 Issue/Rev. 0.2 (10/14) We put you first. And keep you ahead. Smith Meter TOTALIZER/RATE METER The MMRT is a combination

More information

Operating Instructions

Operating Instructions CNTX Contrast sensor Operating Instructions CAUTIONS AND WARNINGS SET-UP DISTANCE ADJUSTMENT: As a general rule, the sensor should be fixed at a 15 to 20 angle from directly perpendicular to the target

More information

WIRING. Connection connector. NPN output type Standard type. Main circuit. High-function type. Main circuit. PNP output type.

WIRING. Connection connector. NPN output type Standard type. Main circuit. High-function type. Main circuit. PNP output type. INSTRUCTI MANUAL Sensor High-performance Digital Display DP-1 Series Thank you very much for using SUNX products. Please read this Instruction Manual carefully and thoroughly for the correct and optimum

More information

Process Transmitter RMA 422

Process Transmitter RMA 422 Technical Information TI 072R/24/ae Process Transmitter RMA 422 Multi-functional 1-2 channel top hat DIN rail unit with loop power supply, alarm set point monitoring, mathematics function and 1-2 analog

More information

VA14 INSTALLATION & OPERATING INSTRUCTIONS

VA14 INSTALLATION & OPERATING INSTRUCTIONS VA14 INSTALLATION & OPERATING INSTRUCTIONS 990053 12/15/05 USA KROHNE Inc. 7 Dearborn Road Peabody, MA 01960 TEL.: +1-978 535-6060 FAX: +1-978 535-1720 e-mail: krohne@krohne.com Proprietary Notice The

More information

Preset counters, electronic

Preset counters, electronic The multifunction preset counters Codix 923 / 924 can be used universally. These preset pulse counters, tachometers or preset timers with up to 6 presets can solve a wide variety of control and monitoring

More information

ACT 10 Digital Keypad Operating & Installation Instructions This manual is found at

ACT 10 Digital Keypad Operating & Installation Instructions This manual is found at ACT 10 Digital Keypad Operating & Installation Instructions 18-00001 This manual is found at www.eaglesecuritysolutions.co.uk Installation Notes Always remember to factory default the controller before

More information

Instruction Manual. Universal Flow Controller Model 261 / 261-EC-01

Instruction Manual. Universal Flow Controller Model 261 / 261-EC-01 Universal Flow Controller Model 261 / 261-EC-01 Instruction Manual Type ARS 261-EC 01 Art.-no: 82212264 Table of Contents 1. Safety Instructions 2. Product ID - Dimensions 3. Function Description 4. Installation

More information

T775U Series 2000 Electronic Stand-Alone Controller

T775U Series 2000 Electronic Stand-Alone Controller T775U Series 2000 Electronic Stand-Alone Controller INSTALLATION INSTRUCTIONS PRODUCT DESCRIPTION The T775 electronic stand-alone controllers are the next generation of universal controls capable of remote

More information

Electronic MICROSTAT-T Temperature controller with digital indication for use with resistance thermometers and thermocouples Series 8650

Electronic MICROSTAT-T Temperature controller with digital indication for use with resistance thermometers and thermocouples Series 8650 M. K. JUCHHEIM GmbH & Co Delivery address:mackenrodtstraße 14, 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: +49 661 6003-0 Fax: +49 661 6003-607 E-mail: mail@jumo.net Internet: www.jumo.de

More information

T775L Series 2000 Electronic Stand-Alone Staging Controller

T775L Series 2000 Electronic Stand-Alone Staging Controller T775L Series 2000 Electronic Stand-Alone Staging Controller INSTALLATION INSTRUCTIONS PRODUCT DESCRIPTION The T775 electronic stand-alone controllers are the next generation of commercial and agricultural

More information

Electrical connection

Electrical connection Splice sensor Dimensioned drawing en 04-2014/06 50116166-01 4mm 12-30 V DC We reserve the right to make changes DS_IGSU14CSD_en_50116166_01.fm Reliable detection of splice on paper web or plastic web With

More information

Smart-Encoder : Optical Incremental

Smart-Encoder : Optical Incremental 1. Introduction The Smart-Encoder effectively eliminates multiple encoder part numbers by bringing intelligence and security to its design. In seconds, a four-digit LED display with two push-buttons enables

More information

Location. Electrical. Loads. 2-wire mains-rated, 0.5 mm² to 1.5 mm² Max. length: 300 m (with 1.5 mm² cable). Example: Belden 8471.

Location. Electrical. Loads. 2-wire mains-rated, 0.5 mm² to 1.5 mm² Max. length: 300 m (with 1.5 mm² cable). Example: Belden 8471. Product Description Installation and User Guide Transistor Dimmer (454) The DIN rail mounted 454 is a fourchannel transistor dimmer that can operate in one of two modes: leading edge or trailing edge.

More information

Single Axis Position Controller

Single Axis Position Controller SERIES P9511 Single Axis Position Controller Compact Construction Simple Go-to operation Integrated Relay Output Integrated Mains Power Supply ELEKTRO-TRADING sp. Z o.o. 44-109 Gliwice, ul. Mechaników

More information

Time meter electronic

Time meter electronic Time meter electronic Universal with dual functions CODIX 52U 000000 0... 30V DIN 24 x 48 Power supply dimensions -0 +50 65 Wide temperature range High IP protection rating Powerful Fast count input Input

More information

MICROMASTER Encoder Module

MICROMASTER Encoder Module MICROMASTER Encoder Module Operating Instructions Issue 01/02 User Documentation Foreword Issue 01/02 1 Foreword Qualified Personnel For the purpose of this Instruction Manual and product labels, a Qualified

More information

ImproX (TRT) Twin Remote Terminal INSTALLATION MANUAL

ImproX (TRT) Twin Remote Terminal INSTALLATION MANUAL SPECIFICATIONS MODEL NUMBER: XRT910-0-0-GB-XX XRT911-0-0-GB-XX XTT911-0-0-NN-XX IMPROX TRT ImproX (TRT) Twin Remote Terminal INSTALLATION MANUAL Working Environment XRT910-0-0-GB-XX... (Aluminium Extruded

More information

INSTALLATION & USER GUIDE

INSTALLATION & USER GUIDE INSTALLATION & USER GUIDE Digidim 458 8-Channel Dimmer STEP 1 Assemble Dimmer Unit STEP 2 Mount Dimmer Chassis STEP 3 Electrical Installation STEP 4 Attach Module and Make Connections STEP 5 Replace Cover

More information

THE ASTRO LINE SERIES GEMINI 1000/2000 INSTRUCTION MANUAL

THE ASTRO LINE SERIES GEMINI 1000/2000 INSTRUCTION MANUAL THE ASTRO LINE SERIES GEMINI 1000/2000 INSTRUCTION MANUAL INTRODUCTION The Gemini 1000 and 2000 are both units in a multi-purpose series of industrial control units that are field-programmable to solve

More information

LAUREL. Laureate Digital Panel Meter for Load Cell & Microvolt Input ELECTRONICS, INC. Features. Description

LAUREL. Laureate Digital Panel Meter for Load Cell & Microvolt Input ELECTRONICS, INC. Features. Description Description LAUREL ELECTRONICS, INC. Features Laureate Digital Panel Meter for Load Cell & Microvolt Input 20, 50, 100, 250 & 500 mv ranges Span adjust from 0 to ±99,999, zero adjust from -99,999 to +99,999

More information

TDEPD. Field-Programmable Pressure Switch/Transducer with Integrated LED Display. Programming Sequence Manual

TDEPD. Field-Programmable Pressure Switch/Transducer with Integrated LED Display. Programming Sequence Manual TDEPD Field-Programmable Pressure Switch/Transducer with Integrated LED Display Programming Sequence Manual Wiring Diagram Pin5 Maintenance Mode + Gray Vent Pin2 Digital Output 2 +/ Analog Output + White

More information

Wall-/Pipe-Mount Level Indicator

Wall-/Pipe-Mount Level Indicator Data Sheet SS/_4 Wall-/Pipe-Mount Level Indicator High visibility 5-digit LED display clear multi-functional indication Analog and 2-relay outputs as standard high, low, latch and rate alarms, plus isolated

More information

2 CHANNEL RECEIVER DISPLAY POTENTIOMETER COM2 NC2 NO2

2 CHANNEL RECEIVER DISPLAY POTENTIOMETER COM2 NC2 NO2 2 CHANNEL RECEIVER RECTSHIVE915-DX Please read this manual carefully before installing the product. 1 DESCRIPTION Receiver Rolling Code, 2 channels with dry contact relay output 20A a 12 Vdc. Programming

More information

DS 400 P. Intelligent Electronic Pressure Switch in Hygienic Stainless Steel Ball Housing. on hygienic process connections

DS 400 P. Intelligent Electronic Pressure Switch in Hygienic Stainless Steel Ball Housing. on hygienic process connections Intelligent Electronic Pressure Switch in Hygienic Stainless Steel Ball Housing Description The electronic pressure switch is the successful combination of hygienic process connections with flush welded

More information

Installation and Setting up Instructions for the 990 Signal Conditioning Instrument

Installation and Setting up Instructions for the 990 Signal Conditioning Instrument Installation and Setting up Instructions for the 990 Signal Conditioning Instrument Contents Page 1.0 Overview... 3 2.0 Installation.. 4 2.1 Electrical connections... 4 2.2 Cable selection... 4 2.3 Electrical

More information

Z-D-IN. RS485 Modbus Module 5 Digital Inputs

Z-D-IN. RS485 Modbus Module 5 Digital Inputs S SENECA Z-PC Line EN Installation Manual Contents: - General Specifications - Technical Specifications - Installation Rules - Electrical connections - Modbus connection rules - DIP-switches Settings -

More information

HS-509 VIBRATION TRIP MODULE

HS-509 VIBRATION TRIP MODULE HS-509 VIBRATION TRIP MODULE 1. Overview The HS-509 is a configurable trip amplifier capable of accepting a 4-20mA signal from a HS-420 sensor and providing two trip action relay outputs along with an

More information

Photoelectric Sensors E3F2

Photoelectric Sensors E3F2 Photoelectric Sensors E3F2 Threaded Cylindrical Photoelectric Sensors with Built-in Amplifier for Use as an Optical Proximity Switch M18 DIN-sized cylindrical housing Housing materials: plastic, nickel

More information

1 Output 1 operation. 3 Pressure unit display. 4 Main display Large 4-character LCD display. 5 Sub-display Small 4-character LCD display.

1 Output 1 operation. 3 Pressure unit display. 4 Main display Large 4-character LCD display. 5 Sub-display Small 4-character LCD display. ure Sensor DP-100 Series INSTRUCTI MANUAL High-performance Digital Display For use outside Japan MEUML-DP100 V1.1 Thank you for purchasing products from Panasonic Electric Works SUNX Co., Ltd. Please read

More information

T775U Series 2000 Electronic Stand-Alone Controller

T775U Series 2000 Electronic Stand-Alone Controller T775U Series 2000 Electronic Stand-Alone Controller INSTALLATION INSTRUCTIONS PRODUCT DESCRIPTION The T775 electronic stand-alone controllers are the next generation of universal controls capable of remote

More information

MT03A Electronic converter for flow rate transmitters

MT03A Electronic converter for flow rate transmitters Instructions manual MT03A Electronic converter for flow rate transmitters The art of measuring R-MI-MT03A Rev.: 0 English version PREFACE Thank you for choosing a Tecfluid S.A product. This instruction

More information

FOM-9010, FOM-9011 and FOM-9012

FOM-9010, FOM-9011 and FOM-9012 Control and Alarm Voltage sense, open collector, or contact inputs Features: FOM-00: Voltage Sense, Open Collector, or Dry Contact Inputs. State Detection for TIA-, TIA-, and TTL Signals. FOM-0: SPDT Form

More information

Electrical connection

Electrical connection Color sensors Dimensioned drawing en 02-2013/01 50121262 068-14515 12mm 32mm 10-30 V DC 500 Hz Scanner for color detection Simultaneous selection of up to 3 colors Detection independent of distance Teach-in

More information

SQM40/41 Actuators for air and gas dampers

SQM40/41 Actuators for air and gas dampers SQM40/41 Actuators for air and gas dampers Description SQM40/41 actuators are used for the positioning of flow control valves, butterfly valves, dampers or any application requiring rotary motion. The

More information

BE3-GPR GENERATOR PROTECTIVE RELAY

BE3-GPR GENERATOR PROTECTIVE RELAY BE3-GPR GENERATOR PROTECTIVE RELAY Behind-the-Panel Mounting Semi-flush Mounting Basler Electric s BE3-GPR generator protective relay offers multiple protective features in a single package. Its microprocessor-based

More information

DS 200 P DS 200 P. Electronic Pressure Switch with Flush Process Connection

DS 200 P DS 200 P. Electronic Pressure Switch with Flush Process Connection with Flush Process Connection piezoresistive pressure sensor up to independent contacts, configurable optional: analogue output Exprotection (for wire) cooling element up to 00 C nominal pressure ranges

More information

Electronic Pulse Counter Combination device

Electronic Pulse Counter Combination device Electronic Pulse Counter Combination device measuring monitoring analysing Input: pulse counter, time meter Display: 6-digit LED Height of digits: 14/8 mm Operation with front-panel buttons Material: plastic

More information

Signet 2551 Magmeter. Contents 1.0 Description 1

Signet 2551 Magmeter. Contents 1.0 Description 1 Signet 55 Magmeter *-55.090-* -55.090- Rev. B 8/05 English English SAFETY INSTRUCTIONS. Depressurize and vent system prior to installation or removal.. Confi rm chemical compatibility before use.. Do not

More information

Q3X Laser Contrast Sensor

Q3X Laser Contrast Sensor Quick Start Guide Laser Expert diffuse sensor with bipolar ( PNP & NPN) output. Patent pending. This guide is designed to help you set up and install the Q3X Sensor. For complete information on programming,

More information

TUSKIN Equipment Corporation

TUSKIN Equipment Corporation TUSKIN Equipment Corporation TC-101 Liquid Color Metering System Operation & Maintenance Manual Warning: Read instructions carefully before attempting to install, operate or service the Tuskin Metering

More information

Model 5250 Five Channel Digital to Analog Video Converter Data Pack

Model 5250 Five Channel Digital to Analog Video Converter Data Pack Model 5250 Five Channel Digital to Analog Video Converter Data Pack E NSEMBLE D E S I G N S Revision 3.1 SW v2.0.1 This data pack provides detailed installation, configuration and operation information

More information

Assembly. Front view. LEDs. Parametrization interface. Power Bus

Assembly. Front view. LEDs. Parametrization interface. Power Bus otation Speed Monitor Features Assembly 1-channel signal conditioner 2 V DC supply Input for 2- or -wire sensors Input frequency 10 mhz... 50 khz elay contact output Start-up override and restart inhibit

More information

User Guide. Centrex Recording Interface

User Guide. Centrex Recording Interface User Guide Centrex Recording Interface Table of Contents Introduction... 2 The Meridian Business Set... 3 Key Numbering Plan (18 button add-on)... 4 Key Numbering Plan (36 button add-on)... 5 Key Numbering

More information

4 Wiring Brochure Wiring and installation of specific control

4 Wiring Brochure Wiring and installation of specific control - Wiring Brochure tekmarnet 4 User Switch 480 W 480 09/09 1 Information Brochure Choose controls to match application 2 Application Brochure Design your mechanical applications 3 Rough In Wiring Rough-in

More information

Pulse Counters, electronic

Pulse Counters, electronic LCD Pulse Counters Codix 0 RoHS Low-price and high efficiency Large -digit LCD display, height of the figures mm [0. ] Optional backlighting Simple counter for fast and slow count pulses, counting direction

More information

Instruction Manual. Series 3000 Model R-165A. Audio/Video IF/RF Relay Panel. CATV Switching and Control

Instruction Manual. Series 3000 Model R-165A. Audio/Video IF/RF Relay Panel. CATV Switching and Control Series 3000 Model R-165A Audio/Video IF/RF Relay Panel Instruction Manual CATV Switching and Control 585-765-2254 fax 585-765-9330 100 Housel Ave. Lyndonville NY 14098 www.monroe-electronics.com Table

More information

ED3. Digital Encoder Display Page 1 of 13. Description. Mechanical Drawing. Features

ED3. Digital Encoder Display Page 1 of 13. Description. Mechanical Drawing. Features Description Page 1 of 13 The ED3 is an LCD readout that serves as a position indicator or tachometer. The ED3 can display: Speed or position of a quadrature output incremental encoder Absolute position

More information

EZ Encoder : Optical Incremental (P Series)

EZ Encoder : Optical Incremental (P Series) 1. Introduction Our EZ Encoders effectively eliminate multiple encoder part numbers by bringing intelligence and security to the design. A four-digit LED display with two push-buttons enables the user

More information

User Manual M1. Direct current / Direct voltage signals 0-20 ma, 4-20 ma, 0-10 VDC. Technical features:

User Manual M1. Direct current / Direct voltage signals 0-20 ma, 4-20 ma, 0-10 VDC. Technical features: M1_61GB.pdf update: 17.09.2014 72x36 User Manual M1 Direct current / Direct voltage signals 0-20 ma, 4-20 ma, 0-10 VDC Technical features: red display of -1999 9999 digits (optional: green, orange or blue

More information

INTRODUCTION / DESCRIPTION. Description

INTRODUCTION / DESCRIPTION. Description INTRODUCTION / DESCRIPTION This manual describes the installation of models 5775X-40X and 5775X- 41X. Because of unique features, these counters may be used in a variety of applications. However, they

More information

User Manual CC DC 24 V 5A. Universal Control Unit UC-1-E. General Information SET. Universal Control Unit UC-1 Of Central Lubrication PAUSE CONTACT

User Manual CC DC 24 V 5A. Universal Control Unit UC-1-E. General Information SET. Universal Control Unit UC-1 Of Central Lubrication PAUSE CONTACT Universal Control Unit UC-1-E User Manual General Information Universal Control Unit UC-1 Of Central Lubrication CC DC 24 V 5A / M 15 SL /MK 31 M Z 30 General Information Contents Universal Control Unit

More information

Digital Indicating ORP Meter AER-101-ORP. Instruction Manual

Digital Indicating ORP Meter AER-101-ORP. Instruction Manual Digital Indicating ORP Meter AER-101-ORP Instruction Manual Preface Thank you for purchasing our AER-101-ORP, Digital Indicating ORP Meter. This manual contains instructions for the mounting, functions,

More information

User Manual M1. Thermocouple type K, B, S, N, E, T, R, L, J. Technical features:

User Manual M1. Thermocouple type K, B, S, N, E, T, R, L, J. Technical features: User Manual M1 Thermocouple type K, B, S, N, E, T, R, L, J Technical features: red display of -1999 9999 digits (optional: green, orange or blue display) minimal installation depth: from 63 mm with plug-in

More information