Rev 02 MLB700. Broadcast Datalink Receiver with Optional RC70 Wireless Remote Control Pilot s Guide

Transcription

1 Rev 02 MLB700 Broadcast Datalink Receiver with Optional RC70 Wireless Remote Control Pilot s Guide

2

3 Date Revision Description 6/14/07 00 Initial Release 6/14/07 01 Updated Remote Control Section 7/26/07 02 Updated Entire Document System Configuration When contacting your Avidyne-authorized distributor or technical support, or when logging onto MyAvidyne.com for the first time, please have the 10 digit hardware serial number and the 12 digit WSI InFlight and SIRIUS Satellite Radio Identification (SID) Numbers available. SIDs are located on the exterior of the MLB700 case, the original packaging, and the packing slip: Hardware Serial Number (Unit S/N): WSI InFlight Serial Number (ESN1): SIRIUS Satellite Radio Serial Number (ESN2): Rev 02 - i - MLB700 Broadcast Datalink Receiver

4 Intentionally Left Blank Rev 02 - ii - MLB700 Broadcast Datalink Receiver

5 Table of Contents Introduction...1 About the SIRIUS Satellite Network...2 WSI InFlight Weather...3 SIRIUS Satellite Radio...3 RC70 Button Descriptions...7 Operation...10 Registering Your MLB700 on MyAvidyne.com...10 Subscribing to WSI InFlight Weather...11 First Power Up...11 Pairing Your Remote with the MLB Replacing the Batteries in the RC Subscribing to SIRIUS Satellite Radio...13 Using the RC70 Remote Control...14 SIRIUS Modes, SIRIUS Menu Option Mode & Advanced Settings Mode...15 Presets...17 Adjusting the Contrast of the LCD Display...24 LCD Timer Feature...25 Appendix - Special Display Messages...26 Appendix - List of Figures...28 Appendix - List of Tables...29 Appendix - Warranty...30 Appendix - Warning and Safety Information...31 FCC Warning...31 FCC Statement for the MLB700 Radio...31 FCC Statement for the Remote Control...32 Remote Control Compliance w/ IC Rules and Regulations...32 General Precautions...33 General Safety Warnings...33 General Safety Cautions...33 Cleaning and Maintenance...34 Copyrights & Trademarks Rev 02 - iii - MLB700 Broadcast Datalink Receiver

6 Introduction Congratulations on your purchase of the MLB700 Broadcast Datalink Receiver with optional RC70 Wireless Remote Control. The MLB700 Broadcast Datalink Receiver is an aircraft Flight Information Service -- Broadcast (FIS-B) receiver that meets the requirements of TSO-C157. The MLB700 is designed to provide reception of weather, and other data products, that will assist flight crews in assessing whether current weather conditions are suitable to the flight characteristics of their aircraft. With a valid subscription through MyAvidyne.com, the MLB700 receives WSI s award-winning InFlight datalink graphical and textual weather for display on the EX500 and EX5000 Multi-Function Display (MFD) systems. In addition, the MLB700 has the ability to receive audio entertainment, with a valid SIRIUS Satellite Radio subscription, that plays through your aircraft s audio system and is controlled from anywhere in the aircraft by the RC70 Wireless Remote Control provided with entertainment enabled systems. Figure 1. MLB700 System Diagram Rev MLB700 Broadcast Datalink Receiver

7 About the SIRIUS Satellite Network The SIRIUS Satellite Network is comprised of three satellites; Radiosat 1, Radiosat 2, and Radiosat 3, which are in a geo-synchronous, highly elliptical orbit. These satellites have a 24-hour orbital period and the elliptical path of the constellation ensures that each satellite spends about 16 hours a day over the continental United States. The primary uplink facility for SIRIUS is located in Vernon, New Jersey. Google Figure 2. SIRIUS three satellites in a 24-hour geo-synchronous orbit. SIRIUS broadcasts using 12.5 MHz of the S band between and MHz. All three satellites can broadcast directly to the MLB700 receiver, and because of their highly elliptical orbit, there will always be two in view at any given time period Rev MLB700 Broadcast Datalink Receiver

8 WSI InFlight Weather: The Weather You Need...From the Source You Can Trust With the MLB700, you will receive WSI s continuous stream of aviation weather information with complete coverage and content for the Continental United States, displayed on an EX500 or EX5000 multi-function display. Among the featured weather products you will receive via the MLB700, is the award winning WSI NOWrad radar mosaic. WSI NOWrad is the only mosaic of the U.S. Doppler Weather Radar network that includes continuous quality control by degreed meteorologists. Additionally, WSI employs a combination of advanced algorithms and up-to-the-minute surface observations to determine the type of precipitation; rain, mixed, or solid. The result is the most accurate depiction of precipitation over the United States available anywhere. SIRIUS Satellite Radio: The Best Radio On Radio From commercial-free music to in-depth sports coverage, news, talk and the hottest entertainment, you can always hear exactly what you want on SIRIUS Satellite Radio. Discover new music or listen to songs you haven t heard in years. Hear live play-by-play and expert talk from the NFL. Listen to 40 games a week from the NBA as well as college sports from more than 150 schools. There is comedy, talk, and entertainment with such well-known hosts as Howard Stern and Martha Stewart. News from Fox, CNN, NPR and the BBC is rounded out with local traffic and weather for the top 20 cities. SIRIUS, the Best Radio on Radio Rev MLB700 Broadcast Datalink Receiver

9 Using the MLB700 for Datalink Graphical Weather The weather data received by the MLB700 can be displayed on EX500 and EX5000 Multi-Function Displays (MFD). For operation and interpretation of the datalink weather products, please consult the EX500 or EX5000 Pilot s Operating Handbook specific to your installation. Using the MLB700 and RC70 for SIRIUS Satellite Radio The MLB700 receives SIRIUS Satellite Radio programming which is sent to the aircraft s audio panel. Depending on your specific installation and audio panel settings, this audio can be played through the headsets and/or cabin speakers Rev MLB700 Broadcast Datalink Receiver

10 Figure 3. Front and Back View of the RC70 Wireless Remote Control Rev MLB700 Broadcast Datalink Receiver

11 2. SIRIUS 3. Set 1. Power LCD Display Screen 4. OK 5. Scroll Left 6. Scroll Right 7. Numeric Keys 8. Enter/Dir 9. Last 12/13 Volume +/- 14. Mute 10/11. Channel +/- 15. Cursor Up 16. Cursor Left 18. Select 17. Cursor Right 19. Cursor Down 20. Exit 22. Band 24. Menu 21. Display 23. Favorite Figure 4. Button Functions of the RC70 Wireless Remote Control Rev MLB700 Broadcast Datalink Receiver

12 RC70 Button Descriptions The following RC70 remote control buttons are currently used with the MLB700 Broadcast Datalink Receiver: Key ID Symbol Key 1 Power Used to wake up the remote. 2 SIRIUS Puts the radio in Normal Mode. 3 Set 4 OK 5 Scroll Left 6 Scroll Right Numerical Entry Used for channel or preset operation Rev MLB700 Broadcast Datalink Receiver

13 Key ID Symbol Key 8 Enter/Dir Used to tune directly to a particular channel. 9 Last Used to return to the previously selected channel. 10 CH+ Channel Up Moves one channel up. 11 CH- Channel Down Moves one channel down. 12 Vol+ Volume Up Used to increase the volume by one. 13 Vol- Volume Down Used to decrease the volume by one. 14 Mute Used to pause sound. 15 Cursor Up Used to scroll up through a channel list or menu. 16 Cursor Left Used to enter the Category List Mode Rev MLB700 Broadcast Datalink Receiver

14 Key ID Symbol Key 17 Cursor Right Used to enter the Category List Mode. 18 Select Used to select a station, menu item or a radio. 19 Cursor Down Used to scroll down through a channel list or menu. 20 Exit Used to exit the current SIRIUS Mode and return to SIRIUS Normal Mode. 21 Display Used to enter SIRIUS Channel List Mode. 22 Band Used to select the band for presets. 23 Fav Favorite. Used to cycle through the presets. 24 Menu Used to enter the SIRIUS Menu Options Mode. Table 1. Active Buttons & Descriptions Rev MLB700 Broadcast Datalink Receiver

15 The following RC70 remote control buttons are currently not used with the MLB700 Broadcast Datalink Receiver: Figure 5. Buttons Not Used with the MLB700 Broadcast Datalink Receiver. Operation Registering Your MLB700 on MyAvidyne.com Prior to proceeding with your MLB700 registration you must have an account on MyAvidyne.com. To create an account you will need a valid account, your aircraft make, model, tail number, and the serial numbers of the Avidyne equipment installed in your aircraft. To subscribe to WSI InFlight Weather and SIRIUS Satellite Radio, you will additionally need a valid Visa/Mastercard/Discover credit card and must be prepared to move your aircraft outdoors to a location with an unobstructed view of the sky, and power up your avionics Rev MLB700 Broadcast Datalink Receiver

16 Subscribing to WSI InFlight Weather Once your MLB700 has been registered, continue with MyAvidyne.com, and select a WSI InFlight Weather subscription plan, provide your credit card number, and finalize your subscription. YOU HAVE 4 HOURS TO MOVE YOUR PLANE OUTDOORS TO A LOCATION WITH AN UNOBSTRUCTED VIEW OF THE SKY, AND POWER UP THE AVIONICS. Avidyne will be transmitting an activation signal over the SIRIUS satellite network to your MLB700, and your WSI InFlight Weather should begin to display on the MAP, TRIP and NRST pages within minutes. Note: Once the avionics master has been switched on, the MLB700 will begin a 3 minute 15 second initialization and self test, Using the RC70 to control the MLB700 requires that the initialization and self test be completed, except during the pairing procedure described below, and it requires that the aircraft is positioned with a clear view of the sky. Power and Start-Up Once power is applied to the MLB700 it begins to initialize and self test, which will take 3 minutes and 15 seconds to complete. When the sequence is complete, providing there is a clear view of the open sky, the MLB700 will begin to gather weather information for display on the EX500 or EX5000 Multi-Function Display, and it will begin to provide audio from SIRIUS Satellite Radio to the audio panel. The first time the device is powered, the SIRIUS Satellite Receiver will be tuned to channel 184. Each time the device is powered after that, it will return to the last station it was set to, at half volume Rev MLB700 Broadcast Datalink Receiver

17 Pairing Your Remote with the MLB700 (For audio enabled units only.) Note: Registering the MLB700 on MyAvidyne.com and subscribing to a weather information service, as per the previous sections, is a prerequisite to pairing the RC70 and MLB700. Prior to subscribing to SIRIUS Satellite Radio pairing the RC70 Remote Control with the MLB700 is required. To pair the devices make sure the aircraft has a clear view of the sky, apply power to the avionics and note the exact time. The MLB700 will begin its initialization and self test, and at the 2 minute and 30 second mark it will begin the transmission of a 30 second signal to the RC70 Remote control. To pair the devices press the SIRIUS button and then press the OK button at the 2 minute and 30 second mark, and the RC70 should briefly display PRESS THE BUTTON ON YOUR SIRIUS RA- DIO, followed by the SUCCESS message. In the event that the SUCCESS message is not observed before the RC70 times out after 30 seconds, powerdown the avionics, wait 5 seconds, and repeat this procedure. Replacing the Batteries in the RC70 To change the batteries in the RC70 Remote Control, slide the battery cover off the back of the remote, replace the 4 AAA batteries, and replace the back cover. Removing batteries briefly and replacing them promptly will not typically result in a need to re-pair the RC70 with the MLB700, however it is possible for the devices to become unpaired. In the event that pairing is lost, repeat the pairing procedure described in the previous section Rev MLB700 Broadcast Datalink Receiver

18 Activation of Your MLB700 Audio Subscription To activate SIRIUS Satellite Radio, an option available with entertainment enabled MLB700s, subscribe online at or call SIRIUS at SIRIUS ( ). Note: THE AIRCRAFT MUST BE OUTDOORS IN A LOCATION WITH AN UNOB- STRUCTED VIEW OF THE SKY, THE AVIONICS MUST BE POWERED-UP, AND THE 3 MINUTE AND 15 SECOND INITIALIZATION AND SELF TEST MUST BE COM- PETE AT THE TIME THE SUBSCRIPTION IS REQUESTED. In order to subscribe to SIRIUS Satellite Radio, know which plans are available, have a credit card ready and use the RC70 Remote Control to tune the MLB700 SIRIUS Satellite Radio to channel 184 prior to contacting SIRIUS. Once the subscription has been completed and the MLB700 has received the activation signal over the SIRIUS Satellite network, SIRIUS Satellite Radio will be available via the aircraft s audio panel Rev MLB700 Broadcast Datalink Receiver

19 Using the RC70 Remote Control SIRIUS Modes, SIRIUS Menu Options Mode, and Advanced Settings Mode The RC70 Remote Control is a universal remote control which is designed for use in a variety of applications. To use the RC70 Remote Control with the MLB700, it must be in one of several SIRIUS Modes, SIRIUS Menu Options Mode or Advanced Settings Mode. SIRIUS Normal Mode is the default. Once the RC70 has timed out, pressing the SIRIUS button once or twice will put the RC70 into SIRIUS Mode. Depending on the mode the RC70 was in when it timed out, pressing OK may also be required to put the RC70 into SIRIUS Mode. In SIRIUS Mode the RC70 may briefly display SIRIUS Conductor before displaying the Normal Mode display, described below. To go from the SIRIUS Menu Options Mode to SIRIUS Mode, press EXIT. To go from the Advanced Settings Mode to SIRIUS Mode, press SET. Power Saving Pressing any button on the RC70 Remote Control will activate the display and provide backlighting. The backlight will remain illuminated for approximately 15 seconds after the last button was pressed, and the display will remain active for approximately 15 seconds longer. Once the display has timed out, pressing any button will cause the backlight to illuminate and will reactivate the display. These timers can be adjusted from the Advanced Settings Mode Rev MLB700 Broadcast Datalink Receiver

20 SIRIUS Normal Mode In SIRIUS Normal Mode the channel number, channel name and the preset information, if any, are displayed in the top line. The second line displays the artists name and the third line displays the song title. (Figure 6) Figure 6. SIRIUS Normal Mode Default Screen. Pressing the DISPLAY button while in SIRIUS Normal Mode switches between the channel name and the channel category. (Figure 7) Figure 7. SIRIUS Normal Mode Category Display Format. SIRIUS Channel List Mode While in the SIRIUS Normal Mode, pressing and holding the DISPLAY button for 3 seconds will put the RC70 into the SIRIUS Channel List Mode. In this mode the CH+ or CH- buttons will tune in the next channel in the list, the CURSOR UP or CURSOR DOWN buttons will scroll through the channels in the list without changing the channel. To tune to a highlighted channel at any time press SELECT. (Figure 8) Rev MLB700 Broadcast Datalink Receiver

21 Figure 8. SIRIUS Channel List Mode Display. Pressing the DISPLAY button while in SIRIUS Channel List Mode will the cycle the display between the channel name, artist s name and the song title. SIRIUS Category List Mode While in the SIRIUS Normal Mode, pressing the CURSOR LEFT or CURSOR RIGHT button switches the display to show SIRIUS channel categories. Pressing the cursor buttons again scrolls through the categories, displaying channels under that category, without changing the channel. Pressing the CURSOR UP or CURSOR DOWN buttons scrolls through the channels in the list without changing the channel. To tune to a highlighted channel at any time press SELECT. (Figure 9) While in SIRIUS Category List Mode pressing the CH+ or CH- button tunes in the next channel in the list Rev MLB700 Broadcast Datalink Receiver

22 Figure 9. SIRIUS Category List Mode Display. Direct Access Control Mode While in SIRIUS Normal Mode, to tune to a known channel directly, press the DIRECT button and enter the 1, 2 or 3 digit number corresponding to the desired channel using the numbered buttons on the RC70. The MLB700 will change channels after pressing 1 or 2 digits and the DIRECT button, or after entering 1 or 2 digits and a time-out, or after pressing 3 digits. Presets You can store up to 30 of your favorite channels as presets for easy tuning. There are 10 presets per band: A, B, and C. Channels are assigned preset numbers 0-9, for example, A1, A2, B1, C1, etc. The current band is displayed in the upper right corner of the default screen (Figure 3), and if the current channel is saved as a preset, the preset number will also be displayed, for example, C Rev MLB700 Broadcast Datalink Receiver

23 Storing a Preset To store a channel as a preset: Tune to the channel you want to store. Select the band by pressing and releasing the BAND button until the desired band is displayed in the upper right hand corner of the display (A, B, or C). Press and hold a numeric button (0-9) in which you want to store until the preset number appears with the band in the upper right hand corner of the display. The channel is now stored as a preset. Note: You can replace previously stored presets by saving over them. Selecting a Preset Channel To select a channel you have saved as a preset: Select the band by pressing and releasing the BAND button until the desired band is displayed in the upper right hand corner of the display (A, B, or C). Press and release the numeric button in which the preset is stored, for example 1. The preset channel is tuned. Selecting a Preset Channel with the FAVORITE Button FAVORITE button to browse through the saved pre- You can also use the sets Rev MLB700 Broadcast Datalink Receiver

24 SIRIUS Menu Options Mode Pressing the MENU button while in the SIRIUS Normal Mode puts the RC70 in SIRIUS Menu Options Mode. Three menu options are available: Signal Indicator, SIRIUS ID, and by scrolling down using the CURSOR DOWN button the Secure Menu option is available. Use the CURSOR UP and CURSOR DOWN buttons to highlight a choice and press the SELECT button to switch to that menu. Use the EXIT button to back out of any of these menus. (Figure 10) Figure 10. SIRIUS Menu Options Mode Display. The Signal Indicator display illustrates the signal strength of both the satellite and terrestrial transmissions that the MLB700 is receiving. Three or more bars indicates a good signal. (Figure 11) Figure 11. Signal Indicator Display Rev MLB700 Broadcast Datalink Receiver

25 The SIRIUS ID option will display ESN1, which corresponds to the Datalink receiver and ESN2 which corresponds to the SIRIUS Satellite Radio receiver. (Figure 12) Figure 12. SIRIUS ID Display. The Secure Menu option allows access to enter or change the password, and once authenticated, allows control over which SIRIUS Satellite Radio channels are available via the MLB700. Additionally, an option to restore the factory settings to the MLB700 is available. To choose the highlighted Menu Option, press the SELECT button, and enter the current or default password, (Figure 13) Figure 13. Secure Options Password Display. Passwords Once authenticated, choose to change the password, lock or unlock channels, or restore factory settings to the MLB700 by scrolling using the CURSOR DOWN button. Press 14) SELECT to choose the highlighted option. (Figure Rev MLB700 Broadcast Datalink Receiver

26 Figure 14. Secure Options Menu. To change the password, scroll to, and select New Password and enter a 4 digit password. (Figure 15) Figure 15. New Password Display. The RC70 will present a confirmation screen and require a confirmation entry. If the password is confirmed, PASSWORD CHANGED will display. (Figure 16) Figure 16. Confirm New Password Display Rev MLB700 Broadcast Datalink Receiver

27 Locking & Unlocking Channels Once the RC70 reverts back to the Secure Menu display, scroll to, and select Lock/Unlock to lock or unlock channels. A list of channels and their current status will be displayed. Scrolling to any channel will display its status. (Figure 17) Figure 17. Lock/Unlock Channel Display. The status of any channel can be changed when it is highlighted by pressing the SELECT button. (Figure 18) Figure 18. Confirm Unlock Display. When the confirmation display appears, press the number 1 button to confirm the change or the number 2 button to discard the change. (Figure 19) Rev MLB700 Broadcast Datalink Receiver

28 Figure 19. Display Showing Unlocked Channel. Factory Restore From the Secure Menu, Factory Restore will revert the MLB700 back to factory settings. This will delete all presets, unlock all channels and set the password back to Settings contained within the RC70 will be retained. Only the settings in the MLB700 will be deleted. (Figure 20) Figure 20. Factory Restore Display Rev MLB700 Broadcast Datalink Receiver

29 Advanced Settings Mode To put the RC70 into Advanced Settings Mode to adjust the display s contrast or timers, from SIRIUS Normal Mode press the SIRIUS button and wait 3 seconds. Press the OK button and wait 1 second. Press and hold the SET button for 3 seconds. Use the LEFT and RIGHT arrow keys to move through the menu options, press Set-Up options. OK to choose Advanced Adjusting the Contrast of the LCD Display You can adjust the contrast setting of the LCD display on the RC70 remote. To change the contrast setting: Press and hold the SET button until the LCD displays INITIAL SETUP. Use the LEFT or RIGHT buttons to go to ADVANCED SETUP and press OK. From ADVANCED SETUP, press LEFT or RIGHT buttons to go to CONTRAST then, press OK. The LCD displays CONTRAST SETUP, with 10 blocks to show the current contrast setting. Press the LEFT or RIGHT buttons to adjust the contrast setting. When you are finished adjusting the contrast press The LCD displays CONTRAST. Press and hold the exit the menu. OK. SET button to Rev MLB700 Broadcast Datalink Receiver

30 LCD Timer Feature The LCD Timer feature allows you to adjust how long the text is displayed after each button press. You can set the time to 10, 20, or 30 seconds. To adjust the LCD Timer: Press and hold the SET button until the LCD displays INITIAL SETUP. Use the LEFT or RIGHT buttons to go to ADVANCED SETUP and press OK. From ADVANCED SETUP, press LEFT or RIGHT buttons to go to LCD TIMER then, press OK. The LCD displays Set TO 20 SECONDS (or the current setting). Press the LEFT or RIGHT buttons to adjust the LCD timer to 10, 20, or 30 seconds. When you are finished adjusting press OK. The LCD displays CONTRAST. Press and hold the exit the menu. SET button to Rev MLB700 Broadcast Datalink Receiver

31 Appendix - Special Display Messages The RC70 remote control may also display status information about the MLB700. These messages are described in the following table. Message Out of Range Acquiring Signal Updating Channels Subscription Upd. Antenna Not Detected Invalid Channel Explanation The RC70 LCD displays Out of Range whenever the wireless controller and the MLB700 cannot communicate because they are too far apart or out of range because of some other interference. The display returns to normal when the wireless controller is again within range of the tuner. The RC70 LCD displays Acquiring Signal whenever the satellite signal is lost. The LCD returns to the normal display automatically when the MLB700 regains the satellite signal. The RC70 LCD displays Updating Channels whenever a channel update from SIRIUS is detected. While the channels update, the percentage of update progress is displayed on the screen. The RC70 LCD displays Subscription Upd. (Updated) whenever SIRIUS broadcasts a subscription update. Press any SIRIUS related key to complete the update. The RC70 LCD displays Antenna Not Detected whenever there is no antenna detected. If this message appears, contact your installer to check that the antenna is securely connected to the MLB700. The normal display returns automatically when the antenna is detected again. The LCD displays Invalid Channel whenever you enter a channel number that does not exist. After two seconds, the current, active channel information, is re-displayed Rev MLB700 Broadcast Datalink Receiver

32 Appendix - Special Display Messages SIRIUS ID Number No Channel Match Operation Timed Out Module is Busy Unsupported Power Mode Bad Command Syntax Command Failed Internal Error <#> To display your SIRIUS ID (SID) number, tune to channel 000. You can also display both the audio and the data SID by selecting the SIRIUS ID from the Menu Option Screen. There are no channels that match the tune request. No response at all from the MLB700 to the RC70 remote control command within approximately one second. This message will be displayed if the MLB700 is to busy to respond to the RC70 remote. This message will be displayed if the MLB700 is waiting to come out of a power down or hibernating state. This message will be displayed if the parameters in a command sent to the MLB700 by the RC70 remote were incorrect. This message indicates that the MLB700 has discovered a problem and cannot identify its source. This message is returned if the error number is not expected. The number can be checked against the MLB700 SSP specification. Table 2. Special Display Messages Rev MLB700 Broadcast Datalink Receiver

33 Appendix - List of Figures Figure Item Description Page Number Figure 1 MLB700 System Diagram 1 Figure 2 SIRIUS 3 Satellites Diagram 2 Figure 3 Front and Back View of the RC70 Remote Figure 4 Button Diagram of the RC70 Remote 6 Figure 5 Buttons Not Utilized with MLB Figure 6 SIRIUS Normal Mode Default Screen Figure 7 SIRIUS Normal Mode Category Format 15 Figure 8 SIRIUS Channel List Mode Display 16 Figure 9 SIRIUS Category List Mode Display 17 Figure 10 SIRIUS Menu Options Mode Display Figure 11 Signal Indicator Display 19 Figure 12 SIRIUS ID Display 20 Figure 13 Secure Options Password Display 20 Figure 14 Secure Options Menu 21 Figure 15 New Password Display 21 Figure 16 Confirm New Password Display 21 Figure 17 Lock/Unlock Channel Display 22 Figure 18 Confirm Unlock Display 22 Figure 19 Display Showing Unlocked Channel 23 Figure 20 Factory Restore Display Rev MLB700 Broadcast Datalink Receiver

34 Appendix - List of Tables Figure Item Description Page Number Table 1 Active Buttons and Descriptions 7 Table 2 Special Display Messages Rev MLB700 Broadcast Datalink Receiver

35 Appendix - Warranty Avidyne warrants this MLB700 Product against any defects in design, material and workmanship for a period of twenty-four (24) months from delivery. Avidyne warrants this RC70 Wireless Remote Control for twelve (12) months from delivery. If any Product supplied by Avidyne hereunder fails to conform to this warranty, Avidyne shall, at its sole discretion, cost and expense, either repair or replace the same or provide a refund for the Product. This warranty is made upon the express condition that: Avidyne is given prompt written notice upon discovery of any nonconformity, with explanation of the alleged deficiencies; Such Product is returned to Avidyne or an Avidyne authorized service facility; The Product has not been altered, modified or changed in any other manner than has been previously authorized by Avidyne; and Repairs to the Product have not been made by anyone other than Avidyne or an Avidyne authorized service facility. This Warranty does not apply to failures caused outside of the normal use of the Product, including improper installation, physical damage, tampering, lightning or other electrical discharge, or to Product with altered serial numbers. Avidyne will use reasonable efforts to repair or replace Product within ten (10) days, and will return repaired Product or will supply replacement Products to the customer at Avidyne s expense. All Products that have been repaired or replaced by Avidyne shall have the remainder term of the original warranty or ninety days, whichever is greater. THIS WARRANTY EXCLUDES ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, ORAL OR WRITTEN, INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY AND/OR WITNESS FOR A PARTICULAR PURPOSE. AVIDYNE WILL NOT, IN ANY EVENT, BE LIABLE FOR ANY DAMAGES INCLUDING ANY LOST PROFITS OR OTHER INDIRECT, SPECIAL, INCIDENTAL OR CONSE- QUENTIAL DAMAGES OF ANY KIND OR TYPE ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT. The foregoing warranty represents Avidyne s exclusive liability Rev MLB700 Broadcast Datalink Receiver

36 Appendix - Warning and Safety Information FCC Warning This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in this Pilots Guide. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. Note: This equipment has been tested and found to comply with Part 15 of the FCC Rules. These rules are designed to provide reasonable protection against harmful interference. This equipment may cause harmful interference to radio communications if it is not installed and used in accordance with these instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, contact your Avidyne authorised dealer or Avidyne Customer Service Center for help. FCC Statement for the MLB700 Radio FCC ID: RZYMLB7XX Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Do not use the remote control. Power down the equipment and remove the batteries from the remote. Contact your Avidyne authorized dealer or Avidyne Customer Service Center for help. This product complies with FCC OET Bulletin 65 radiation exposure limits set forth for an uncontrolled environment. Changes not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Rev MLB700 Broadcast Datalink Receiver

37 FCC Statement for the Remote Control FCC ID: MG This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide a reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiated radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to contact your Avidyne authorized dealer or Avidyne Customer Service Center for help. Remote Control Compliance with IC Rules and Regulations IC: 2575A-URC10000 Model: URC Universal Electronics Inc. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and radiates radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures, contact your Avidyne authorized dealer or Avidyne Customer Service Center for help. The user is cautioned that changes and modifications made to the equipment without the approval of the manufacturer could void the user s authority to operate his equipment Rev MLB700 Broadcast Datalink Receiver

38 General Precautions Avidyne disclaims all liability for hearing loss, bodily injury or property damage as a result of the use or misuse of this product. General Safety Warnings Be sure to observe the following warnings. Failure to follow these safety instructions and warnings may result in a serious injury or death. Do not open, disassemble, or alter the units in any way. Doing so may result in fire, electric shock or product damage. Do not insert any objects into the units. Doing so may result in fire, electric shock or product damage. Make the correct connections. Failure to make proper connections may result in fire or product damage. Do not splice into electrical cables. Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock. Do not install the units in areas where there are high levels of humidity, moisture, or dust. Doing so can result in electric shock or product failure. Do not drop the unit or subject in to strong shocks. If the unit doesn t seem to be working properly, turn the unit off, wait 10 seconds, and the turn it on again. General Safety Cautions Be sure to observe the following cautions. Failure to follow these safety cautions may result in injury or material property damage. Halt use immediately if a problem appears. Failure to do so may cause personal injury or damage to the product. Return the tuner to your Avidyne authorized retailer or Avidyne Customer Service Center for repairing Rev MLB700 Broadcast Datalink Receiver

39 Cleaning and Maintenance If the tuner or wireless controller becomes dirty, turn the power off and wipe it clean with a soft clean cloth. Do not use hard cloths, paint thinner, alcohol, or other volatile solvents to clean. These may cause damage to the unit. Copyrights & Trademarks Copyright 2007 Avidyne Corporation. All Rights Reserved. SIRIUS and related marks, the SIRIUS dog logo, channel names and logos are registered trademarks of SIRIUS Satellite Radio Inc. All Rights Reserved. Z-Wave is a registered trademark of the Z-Wave Alliance. Hardware, subscription, and activation fee required. For full Terms & Conditions, visit Prices and programming are subject to change. Not available in HI and AK. Equipment and subscription sold separately. Installation required with some equipment Rev MLB700 Broadcast Datalink Receiver

40

41 Avidyne Corporation 55 Old Bedford Road Lincoln, MA Telephone: Toll Free: 800-AVIDYNE ( ) Fax: Rev 02 MLB700 Broadcast Datalink Receiver 2007 Avidyne Corporation. All Rights Reserved. Avidyne and the Avidyne logo are registered trademarks of Avidyne Corporation in the United States and/or other countries. Sirius and the Sirius logo are registered trademarks of Sirius Corporation in the United States and/or other countries. WSI and the WSI logo are registered trademarks of WSI Corporation in the United States and/or other countries.