Glow P7B LED Par Beam

Transcription

1 Glow P7B LED Par Beam USER MANUAL GLOW P7B LED PAR BEAM- 15W*7PCS-RGBW-4-IN-1

2 TABLE OF CONTENTS 1.Summary 3 Product Introduction 3 Content List 3 2. Safety Information 3 Safety notes 3 Safety instructions 4 3. Product diagram 4 4. Features 5 5. DMX Control 5 DMX Channel(3CH) 5 DMX channel(4ch) 6 DMX channel(5ch) 6 DMX channel(8ch) 6 DMX Channel(9CH) 7 6. Menu Instructions 8 Operating instruction: 10 Details of In-built program (Pr- -) Operating Control InstructionS 11 Master/Slave XLR cable connecting 11 XRL cable Wiring diagram Trouble Shooting Technical Specifications 14 2

3 SUMMARY Thank you for purchasing our Glow P7B Par Beam. Please read these instructions carefully before operating the system to avoid any possible damage or misuse. PRODUCT INTRODUCTION The LED Par Glow P7B LED Par Beam, encased in a full plastic shell, has a light source that uses high powered OSRAM 4-in-115W LED lights, each made up of R, G, B, and W LEDs. This fixture has a long life span, low power consumption, good colour mixing effects and high brightness. Each LED can also be independently dimmed and altered. The built-in programs include dimming, strobe, gradual change, fading, gray change etc. settings. It is recommended that an international standard DMX 512 signal is used for best results.. CONTENT LIST Ø LED PAR GLOW P7B LED PAR BEAM (x1) Ø DMX cable (x1) Ø Unser manual (x1) Ø Warranty Card (x1) 2. SAFETY INFORMATION SAFETY NOTES Seek advice from a professional prior to authoring any repairs Always ensure the system is disconnected from the power source before assembling, deconstructing and moving Avoid direct eye exposure when in use 3

4 SAFETY INSTRUCTIONS Ensure the power supply voltage corresponds with the required voltage for the lights, and is within the range of the requested technical restrictions. Before installing, check the lights fasteners and mechanical structures are in good condition and there is no apparent damage. This light is designed for indoor and outdoor use, however the working temperature must be kept below 50 degrees. The fixtures can be mounted in any position, provided there is adequate room for ventilation. Make sure there are no inflammable and explosive items within 0.5 meters of the fixture. The yellow/green cables are for earthling safety. These should not flicker when fixture is in use. 3. PRODUCT DIAGRAM 4

5 4. FEATURES o The Light Source uses OSRAM 15W LED and 4 in 1 chip technology (R, G, B, W), has low power consumption, effective brightness, stable capability and a long life expectancy. o Its special secondary LED lenses ensure it has high quality light and good color mixing o Each LED color has dimming, and has 5 different modes of dimming. o 4-button MDX address setting and LED display panel with ON/OFF function o Liner dimming from 0-100% (including strobe, gradual change, jumping change etc effects) o Auto run /master slave/interconnected multi-machine control o Uses a switching power supply to protect the LED o Lenses angel:45º o Optional DMX Channel DMX CHANNEL(3CH) 5. DMX CONTROL Channel DMX value Control Function Remarks 1CH RGB mixing Hue 2CH White dimming Color Saturation 0-100% 3CH General dimming 0-100% purity Note: In this model, hue represents the visible light (ie. red, green, yellow, blue etc.) Color Saturation is the main colour proportion that is being used. 100% Colour Saturation mean the color has reached purity. Purity value is the Brightness of the color when the colour has reached 100% (its brightest state) 5

6 DMX CHANNEL(4CH) Channel DMX value Control Function Remarks 1CH R 0-100% 2CH G 0-100% 3CH B 0-100% 4CH W 0-100% DMX CHANNEL(5CH) Channel DMX value Control Function Remarks 1CH General dimming 2CH R 0-100% 3CH G 0-100% 4CH B 0-100% 5CH W 0-100% DMX CHANNEL(8CH) Channel DMX value Control Function Remarks Priority 1CH General dimming 2CH RED dimming 0-100% 3CH Green dimming 0-100% 4CH Blue dimming 0-100% 5CH White 0-100% 0-14 Dimming When CH7 is 6CH Strobe Speed over 31, this function is Invalid 0-31 Invalid 7CH From dark to bright From bright to dark From dark-brightdark Gradient Speed Must use CH1, 2, 3, 4, 5 otherwise the light will not work. Speed adjustment from CH

7 Dark-bright-dark auto run Colour jumping adjustment from CH Sound control Not for waterproof lights 8CH Speed Adjustment (7CH) Slow to fast DMX CHANNEL(9CH) Channel DMX Control Function Remarks Priorit value y 1CH General dimming 2CH RED dimiming0 100% 3CH Green dimming0 100% 4CH Bule dimming0 100% 5CH White 0 100% 6CH 7CH 0-14 Dimming When CH7 is Strobe Speed over 31, this function is Invalid 0-31 Invalid From dark to bright From bright to dark From dark-brightdark Gradient Must use CH1, Dark-bright-dark auto run Colour jumping 2, 3, 4, 5 otherwise the light will not work. Speed adjustment from CH

8 Sound control Not for waterproof light 8CH Speed Adjustment Slow to fast 9CH (7CH) As display setting : DIMMER0-4 DIMMER0 DIMMER1 DIMMER2 DIMMER3 DIMMER MENU INSTRUCTIONS Addr d001-d512 DMX Mode SLAU SL.AU Slave mode CHnd SP-- 3CH\4CH\5CH\8CH \9CH SP00-SP15 DMX channel choosing Modify Built-in program speed Pr-- Pr00-Pr30 Built-in program ASC- AC00-AC15 Color Jumping MENU FAdE FA00-FA15 Gradual Changing mode FLAS FL00-FL15 White strobe mode 8

9 rl-- r.000-r.255 Red dimming GL-- G.000-G.255 Green dimming bl-- b.000-b.255 Blue dimming UL-- U.000-U.255 White dimming SouA So.uA Sound Activated LED on/off Display on/off node UErn nod0-nod4 UE2.0 DMX dimmer mode The version No. of the software 9

10 OPERATING INSTRUCTION: MENU(UP/DOWN) + (ENTER) + (UP/DOWN) + (ENTER) Exp: Select the DMX mode: o Press the MENU to go back to the initial setting. o Press UP/DOWN to display Addr. o Press ENTER to change the content. The display will flash. o Press UP/DOWN to change the address code and select d001. o Press ENTER to select and store the current menu options. DMX mode will be stored automatically and the screen will stop flashing. Exp: Select DMX Channels optional mode: o Press MENU to go back to the initial setting o Press UP/DOWN to display CHnd o Press ENTER to change the content. The display will flash o Press UP/DOWN to select the DMX channels that you need (ie. 3CH, 4CH, 5CH and so on) o Press ENTER to select and store the current menu options. DMX mode will bestored automatically and the screen will stop flashing. Exp: turn off the display: o Press MENU to go back to the initial setting o Press UP/DOWN to display LED o Press ENTER to change the content. The display will flash. o Press UP/DOWN to select OFF o Press ENTER to confirm, and then select the working mode that you desire. Note: When the machine has not been in use for a period of time, the display will turn off. If the display turns off, press any button to reactivate. DETAILS OF IN-BUILT PROGRAM (PR- -) o Press MENU to go back to the initial setting o Press UP / DOWN to display Pr--- o Press ENTER to select. The display will flash o Press UP / DOWN to change the address code to select pr00 o Press ENTER to select and store the current menu options. DMX mode will be stored automatically and the screen will stop flashing. Pr14 - Pr30 Can change the content of SP and change the speed of jumping (SP00 is the fastest, SP15 is the slowest) Pr00-Pr13:R, G, B, W single color or multi-colors lighting Pr14-Pr28:correspond with the Pr00-Pr13 and adds the strobe function. Pr29:Single colour jumping. Pr30:Multiple colors jumping 10

11 7. OPERATING CONTROL INSTRUCTIONS MASTER/SLAVE Master setting: The master should be one of following modes: built-in mode, color jumping mode, fade mode, white strobe mode or manual dimming mode. This sends out a synchronized signal to the slave. To avoid the master signal and DMX512 signal from interfering with each other, the DMX512 signal must be cut off. When the signal cables are longer than 60 meters, a DMX signal amplifier is necessary. Slave setting: Settings must be in the SLAV mode and the address code should be A001 to assure the master s signals are received correctly. Only one light can be set as a Master and the remaining are slaves. XRL CABLE 8. XLR CABLE CONNECTING The standard connection of the XRL should have one end connecting to the male plug, and the other connecting to the female. As below: pin 1 - ground, pin 2 - negative signal, pin 3 - positive signal 11

12 Note: In order to avoid failures and interference with signal transmission, connect a resistance 120 (1/4W)at the end of the DMX connection as shown below: The conversion between 3 pin and 5 pin XLR. If the output cable of the DMX512 controller is a 5PIN, a 5PIN to 3PIN cable is necessary. 9. WIRING DIAGRAM 12

13 10. TROUBLE SHOOTING Problem The light won t turn on Suggestions Check if the power plug is working normally Check if the light switch is off or on Check if the power supply is working normally The DMX is not controlling the light The display is not working The LED is not light Some of the LEDs are not light Single color LEDs Check if the DMX cable is connected to the light properly Check if the DMX512 controller is working normally. Check if the DMX cable is damaged. Check if the light is in DMX mode (Addr:001). When the electricity is connected, the LED should flash once. If this is not the case, check the power switch and transformer. Check if the power input of the IC board is working. Check if the cable connected to the display is secure. Change the main board to ensure that it is working properly. Change the display. When the electricity is connected, the LED should flash once. If this is not the case, check the power switch and transformer. Check if the power input of the IC board is working. Check if the cable connected to the display is secure. Change the main board to ensure that it is working properly. Check if the LEDs are secure, as the LED is connected by LEDs in series. Use the multimeter (diode) to check if the LED is bright or not. If not, the LED will need replacing. Check constant current IC is working properly (compared with the normal IC). Check if the voltage of the input end of corresponding color is 13

14 are always light/not working. light at all Change the IC control board. Note: Seek advice from a professional prior to authoring any repairs 12. TECHNICAL SPECIFICATIONS o Input voltage:ac 100V-264V/47-63HZ o Output voltage:dc24v o Consume:144W o Lamp Type:High Power LED(8W) o Lamp Spec:4-in-1 8W(18PCS) o Constant current driver:500ma o Refresh rate:>400hz o Life span: 50000~100000hours o Control Signal:DMX512, sound activeted,auto run o Control mode:stand alone/ sound activated o Channel:3,4,5,8CH o Color effect:rgbw mixing o Function Effect:dimmer, strobe, eotic, gradual change,sound activeted o Beam Angle: 15, 25,45 14