LEVO SERIES DIGITAL CLOCKS/TIMERS
|
|
- Norah Payne
- 5 years ago
- Views:
Transcription
1 XR TIME SYNCHORNIZATION LEVO SERIES DIGITAL CLOCKS/TIMERS INSTALLATION GUIDE Doc Part No.: XRDOC
2 Legal Notice Copyright 2016 Primex Wireless, Inc. All rights reserved. U.S. Patents 6,873,573; 7,352,657. Other Patents Pending. Printed in the USA. Information in this document is subject to change without notice. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical or otherwise, for any purpose, without the prior written permission of Primex Wireless. PRIMEX WIRELESS LOCATIONS Worldwide Headquarters 965 Wells Street Lake Geneva, WI Phone: (855) Hours: 7:00 AM to 5:00 PM CST info@primexinc.com UK Office Unit G420 Dean Clough Halifax, West Yorkshire HX3 5AX Phone: Hours: 8:30 AM to 5:00 PM info@primexwireless.co.uk Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 2
3 CONTENTS Primex Wireless Locations 2 About this Guide 5 Regulatory Compliance 6 Important Safety Instructions 7 Levo Series Digital Clocks/Timers Specifications 8 Digital Clock/Timer Specifications - Levo Series 8 Digital Clock/Timer Components - Levo Series 9 Digital Timer Features 10 Configure Digital Clock and Timer Settings - Levo Series 12 Set LED Dimmer Display - Levo Series 12 Set Alternating Time/Date - Levo Series 12 Set Display to 24-Hour Time - Levo Series 13 Set PM /Indicator - Levo Series 13 Set Offset Hours - Levo Series 13 Set Audible Buzzer (Timer Models Only) - Levo Series 14 Set Programmable Timer Mode (Programmable Timer Only) - Levo Series 14 Install Levo Series Digital Clock/Timer 15 Installation Requirements 15 Surface-mount Dimension Specifications - Levo Series 16 Tilt-Bracket and Surface-mount Mounting Dimensions VAC Wiring 19 24VAC Wiring 19 Surface-mount Installation - Levo Series 20 Tilt Bracket Installation - Levo Series 22 Remove Clock/Timer from Bracket - Levo Series 23 Dual-mount Digital Clock/Timer Installation - Levo Series 24 Dual-Mount Dimension Specifications 27 Remove Dual-Sided Digital Clock from Mounting Bracket 27 Flush-mount Clock/Timer Installation - Levo Series 28 Flush-Mount Dimension Specifications - Levo Series 31 Remote Antenna Installation 32 Timer Control Switch Installation - Levo Series 34 Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 3
4 Digital Code Blue Timer and Elapsed Timer Operation 36 Code Blue Timer Operation 37 Code Blue Count Mode 37 Elapsed Timer Operation 38 Normal State - Timer Mode 38 Set State - Timer Mode 39 Digital Programable Timer Operation 40 Support 41 Warranty 42 Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 4
5 ABOUT THIS GUIDE Purpose This guide is intended to provide the instructions and information required to install and operate Primex Wireless Levo Series Digital Clocks/Timers. Typographical Conventions This guide includes notes, cautions, and warnings content that highlights important messages. Typeface Note Caution Warning Example Indicates Indicates something important or useful. Indicates a command or procedure may have an unwanted or undesirable result. Indicates a command or procedure that could be dangerous to system or device. Provides an example of how the topic can be configured or used. Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 5
6 REGULATORY COMPLIANCE FCC/IC Product Compliance This device complies with part 15 of the FCC rules as well as with Industry Canada. Operation of this device is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference that may cause undesired operation. Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 6
7 IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE INSTALLATION, OPERATION, OR MAINTENANCE OF PRODUCT. Some of the following information may not apply to your particular product model; however, as with any electronic product, precautions should be observed during installation, operation, and maintenance. Installation must conform to state or local building codes and ordinances. Installation or maintenance should be performed only by qualified personnel as defined in the Local Electrical Code. Mount in location where device will not readily be subject to tampering. Any wiring instructions must be followed precisely. Failure to do so could cause permanent equipment damage. To avoid possible electric shock or damage to the device, disconnect power source before installation or servicing. Do not install or use device near water. To reduce the risk of electrical shock, do not expose device to rain or moisture. Device must not be exposed to dripping or splashing and no objects filled with liquids, such as vases, must be placed on the device. Device is designed for indoor use only. Operating outdoors, or in wet areas, is an electrical hazard and may damage the equipment while nullifying the warranty. Device is cleanable with a cloth moistened with water or a common disinfectant. Be sure to test any cleaning solutions on a small area of the clock before using it on the entire device. For healthcare facilities, devices are not intended for patient use and must not be installed within 6ft (2m) of patient contact. AC-Power Pluggable Clock/Timer Models AC main power supply must be disconnected while installing or performing maintenance of any device. To completely disconnect the power input, the main plug should be disconnected from the main socket outlet completely. The main socket outlet must provide a protective earthing connection where the outlet has a protective earth (ground) connection. Main plug is used as disconnect device and it should remain readily operable during intended use. AC-Power Hardwired Clock/Timer Models AC power must be supplied from a circuit that has a resettable circuit breaker. AC mains power supply must be disconnected while installing or performing maintenance of any device. Open the circuit breaker supplying the device before attempting installation, maintenance, or repairs. Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 7
8 LEVO SERIES DIGITAL CLOCKS/TIMERS SPECIFICATIONS Digital Clock/Timer Specifications - Levo Series Table 1: Digital Clock/Timer Specifications Parameter LED Display Specification Highly visible 7-segment LED digits 2.5" model: 2.5 (6.4 cm) diagonal (hours and minutes), 1.4" (3.6 cm) diagonal (seconds) LED Display Dimmer 100%, 75%, 50%, 25% 4" model: 4.6 (11.7 cm) diagonal (hours and minutes), 2.5 (6.4 cm) diagonal (seconds) Time Display 12- or 24-hour time PM indicator light Alternating time and date display option Hour Offset +/- 24 hours Receiver Sensitivity (Decode) < -110dBm Power Supply XR Levo Series: VAC/ cycle. Supplied with 10 (3.0 m) cord with plug and UL/cUL listed power supply Storage Temperature Range -20 to 185 F ( C) 24VAC model: 18-28VAC/ cycle. Supplied with a 10" (25 cm) cord with pigtail and power supply Operating Temperature Range 32 to 194 F (0-35 C) Code Blue Timer Input VAC/ DC /DC or dry contact input Code Blue and Elapsed Timer Audible Beep Option Frequency 3KHz +/-0.5KHz NOTE: All specifications subject to change without notice. Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 8
9 Digital Clock/Timer Components - Levo Series Key-hole mount (2); secure mount Power supply Power cord with 2-prong plug Power cord strain relief assembly Setting panel; configure clock settings and location of Reset button Code Blue Timer: 4 pin connector 30 in. (76.2 cm) length; RJ 11 jack for connection from the timer to the timer control switch The figure below illustrates the back of a Levo Series Digital Clock/Timer and its components. Figure 1: Clock/Timer Back View Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 9
10 Digital Timer Features Digital Code Blue Timer Capability of functioning as a normal clock, code blue timer, and elapsed timer with both count-up and countdown options. When power is applied it begins operating as a digital clock. Digital Elapsed Timer Capability of functioning as a normal clock and timer with both count-up and count-down options. When power is applied it begins operating as a digital clock. Digital Programmable Countdown Timer Capability of functioning as a normal clock and count-down timer using the schedule programmed in the Primex Wireless Event Scheduler Pro Software. When power is applied it begins operating as a digital clock. Backup Power The timer has a power outage memory backup. In the event of a power outage, the timer's memory will maintain the correct time for a minimum of one (1) hour without power. This feature requires a minimum one hour of charging time. Up Counter Features The up counter can count up from any preset time to 99:59:59 (99 hours, 59 minutes, 59 seconds). The decimal point on the far left (near the 10 hour digit) lights up to indicate up counter function. The user can preset count up start time. Up-counters can count from 00:00:00 to 99:59:59 (99 hours, 59 minutes, 59 seconds). The display flashes every second and the clock beeps for 3 seconds when 99:59:59 is reached. Down Counter Features The count-down timer can count down from a preset time to 00:00:00. The decimal point on the far right (near the minutes/seconds digits) lights up to indicate down counter function. The user can preset count-down start time. Down counters can count from 99:59:59 to 00:00:00. The display flashes every second and the clock beeps for 3 seconds when 00:00:00 is reached. Audible Tone Option Only on the count-up and count-down functions Frequency 3KHz +/-0.5KHz Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 10
11 Timer Switch Control Elapsed Timer function is triggered by the use of the switch control; allowing a user to run, hold, or reset the timer events. Code Blue Timer function is triggered by the input of the wired connection to the code blue system and the use of the switch control allows a user to halt a code blue event. Designed to fit inside a single gang box (not supplied); typically in. x in. x 4 in. (11.45 cm x 6.99 cm x cm) Timer Switch Control can simultaneously activate two connected timers for even more accurate time management Membrane switch and wall plate clean easily and resist common cleaners and disinfectants. Be sure to test any cleaning solutions on a small area Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 11
12 CONFIGURE DIGITAL CLOCK AND TIMER SETTINGS - LEVO SERIES To change the factory default settings, from the back side of the clock, remove the small rectangular access panel. Setting changes can be made while the clock/timer is ON and changes will take effect within a few seconds. NOTE: When power is first applied to the clock or the reset button is pushed, a decimal point will flash for approximately three minutes while the clock/timer receiver is turned on to capture the transmitter signal. If the clock/timer does not receive valid time data from the transmitter for 72 hours, the red colon on the clock will flash. Set LED Dimmer Display - Levo Series NOTE: The LED Display is set to 100% by factory default. To dim the LEDs by 25%, set the OPTIONS, DIM switch 1 to the OFF position and DIM switch 2 to the ON position, as illustrated below. Figure 2: Dimmer 25% To dim the LEDs by 50%, set the OPTIONS, DIM switch 1 to the ON position and DIM switch 2 to the OFF position, as illustrated below. Figure 3: Dimmer 50% To dim the LEDs by 75%, set the OPTIONS, DIM switch 1 to the ON position and DIM switch 2 to the ON position, as illustrated below. Figure 4: Dimmer 75% Set Alternating Time/Date - Levo Series To set the display to alternate between Time and Date, set the HR OFFSET- Time/Date switch (1) to the ON position, as illustrated below. Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 12
13 Figure 5: Alternating/Time Date Set Display to 24-Hour Time - Levo Series To display 24-hour time, set the HR Offset - 12/24 HR switch (2) to the ON position, as illustrated below. Figure 6: 24-Hour time Set PM /Indicator - Levo Series To enable the PM dot indicator, set the OPTIONS - PM DP switch (6) to the ON position, as illustrated below. Figure 7: Activate PM/Indicator Set Offset Hours - Levo Series The clock/timer displays the time received from the transmitter. The hour offset is for application use where the clock/timer is set to display the time for another time zone. By moving the appropriate HR OFFSET dip switch(s) and the direction (+/-) dip switch, any full-hour time can be displayed. The HR OFFSET switch designates how many hours are offset from the current transmitter time zone. The clock reads the hour offset on start up, when the RESET button is pushed, and each time the clock receives data from the transmitter for the offset hours to go into effect. Figure 8: Set Offset Hours Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 13
14 Set Audible Buzzer (Timer Models Only) - Levo Series The audible buzzer is only on the count-up and count-down timer function. To enable the buzzer feature, set the OPTIONS - Buzzer switch (3) to the ON position, as illustrated below. Figure 9: Audible Buzzer Set Programmable Timer Mode (Programmable Timer Only) - Levo Series For Programmable Timer models, the timer schedule is configured in the Primex Event Scheduler Pro software to the schedule ID controller 24. The schedule is downloaded from the Event Scheduler Pro to the system transmitter, allowing the transmitter to broadcast the schedule. To enable a programmable timer to receive the broadcast schedule from the transmitter, set the PT/TC Switch (5) to the ON position, as illustrated below. Figure 10: PT/TC Switch - Programmable Timer Use Only Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 14
15 INSTALL LEVO SERIES DIGITAL CLOCK/TIMER Installation Requirements Refer to the Important Safety Instructions before installing, operating or performing maintenance of clocks. Before installing a clock, verify the system transmitter is operating properly and sending a signal with adequate building coverage (refer to the guide accompanying the transmitter). A transmitter with an internal antenna broadcasts continuously and a transmitter with an external antenna broadcasts hourly from 39 minutes past the hour to 6 minutes after each hour. Cycling the transmitter power off/on initiates an 8 hour continuous broadcast. Clocks must be installed at a location within adequate transmission range of the transmitter. Verify the clock's settings have been configured before the clock is installed. Any damage to the clock due to improper wiring voids the warranty. It is at Primex Wireless discretion as to whether damage to the clock was caused by improper wiring. NOTE: When clocks are being installed or the signal is tested at the final installation location to verify the presence of the transmitter signal in that area, push and IMMEDIATELY release the button and hang the clock in place. It is very important not to hold the button down too long or the hands will proceed to the 12 o'clock position and remain there indefinitely. To make the hands move again, wait until they have stopped, then press and hold the button again. The clock will enter its normal set up procedure and set itself. Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 15
16 Surface-mount Dimension Specifications - Levo Series Figure 11: 2.5" x 6 Digit Clock Type Weight Max. Current Draw Height (A) Width (B) Depth (C) 2.5" (6.4 cm), 6- digit 2.0 lbs. (0.9 kg) 230 ma 5.0" (12.7 cm) 13.75" (34.9 cm) 2.2" (5.6 cm) 2.5" (6.4 cm), 4- digit 1.8 lbs (0.8 kg) 170 ma 5.0" (12.7 cm) 10.8" (27.4 cm) 2.8" (5.6 cm) 4" (10.16 cm), 4- digit 3.9 lbs. (1.8 kg) 240 ma 8.0" (20.3 cm) 17.9" (45.5 cm) 2.4" (6.1 cm) 4" (10.16 cm), 6- digit 4.6 lbs (2.1 kg) 260 ma 8.0" (20.3 cm) 2.3" (59.3 cm) 2.4" (6.1 cm) Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 16
17 Tilt-Bracket and Surface-mount Mounting Dimensions Dimension D - clock screw hole spacing Dimension E - distance to wall surface for 4 mounting bracket Dimension F - distance to wall surface for 18 mounting bracket Dimension G/H - mounting bracket screw hole spacing Figure 12: Single Digital Clock/Timer Mounting Dimensions Illustration Table 2: Single Digital Clock/Timer Mounting Dimensions Clock/Model A B C D E F G H digit - 4 bracket N/A digit - 4 bracket " N/A digit - 18 bracket 4.6" 10.6" 2.2" 6.0" N/A 2.1" 9.5" 2.5" digit - 18 bracket 4.6" 13.6" 2.1" 6.0" N/A 2.1" 9.5" 2.5" Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 17
18 Clock/Model A B C D E F G H 4 4-digit wall mount N/A digit wall mount " N/A Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 18
19 120VAC Wiring Primex Levo Series Digital Clocks/Timers are shipped from the factory with a power supply and power cord with 2-prong plug. The power plug may be removed and cord cut to length for hardwired (pigtail) installation. Pigtail installation requires a 120V~ power line in a junction box installed by a licensed electrician. Leave a minimum of 6 in. (15 cm) of cord inside the junction box. 24VAC Wiring Primex Levo Series Digital Clocks/Timers operate at a maximum current draw of 1.2A (24VAC) and operate over a range of 18-28VAC. Follow all National and Local Building Codes when installing clocks. All clocks should be connected to a single power source. If multiple power sources are needed to accommodate the load of the clocks, all of the power sources should have the same rating and be installed on separate branch circuits. Never install different size power sources on the same branch circuit. For installations where 24VAC wiring exists, the gauge/length of the wire and rating for the supply transformer should be verified to ensure adequate current supply and voltage for all connected devices. For new installations, the supply wire gauge should be determined to ensure acceptable voltage drop based on installed length from the supply transformer to most distant clock to ensure minimum voltage (18VAC) is assured. Use two wire nuts, sized appropriately for the gauge of wire, to secure building supply wires to wires extending from clock power supply. Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 19
20 Surface-mount Installation - Levo Series Complete the instructions below to install a digital clock/timer directly to the surface of a wall. NOTE: Most building codes prohibit the use of hard-wired power connections for devices that can be removed without tools. Clock/timers mounted directly to a wall must have standard power plugs. Installation Mount the clock/timer directly to the wall with the two #10 screws and anchors (supplied). To determine the spacing of the screws, see "Tilt-Bracket and Surface-mount Mounting Dimensions" on page 17. Upon applying power to the digital clock/timer or when pressing the Reset button located in the setting panel, the clock initiates its power up sequence as described below. 1. All 8 LED segments display 8 s with a red dot on the bottom right of each of the two hour digits and one at the second or last minute digit. 2. All LED segments display dashes and then dashes with a colon between the hours and minutes. 3. Once the clock/timer receives a signal from the transmitter, the LED segments display the time received from the transmitter s time source and a flashing red dot appears at the bottom right of the second hour digit for three minutes. Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 20
21 Figure 13: Surface Mount Illustration Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 21
22 Tilt Bracket Installation - Levo Series Complete the instructions illustrated below to mount a digital clock/timer using the supplied tilt mount bracket. You may mount the tilt bracket directly to the wall with the four #10 screws and anchors (supplied). For additional information, see "Tilt-Bracket and Surface-mount Mounting Dimensions" located on page 17. Hard-wired installation requires a 120V~ power line in a junction box installed by a licensed electrician. The tilt bracket has a center pass-through hole for the 120V~ pigtail. If a junction box is present, the tilt bracket also has mounting holes spaced to allow direct attachment of the tilt bracket to the cover plate screw holes on the junction box. Upon applying power to the digital clock/timer or when pressing the Reset button located in the setting panel, the clock initiates its power up sequence as described below. 1. All 8 LED segments display 8 s with a red dot on the bottom right of each of the two hour digits and one at the second or last minute digit. 2. All LED segments display dashes and then dashes with a colon between the hours and minutes. 3. Once the clock/timer receives a signal from the transmitter, the LED segments display the time received from the transmitter s time source and a flashing red dot appears at the bottom right of the second hour digit for three minutes. Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 22
23 Remove Clock/Timer from Bracket - Levo Series 2.5 x 4 and 2.5 x 6: From the top of the bracket, using a screwdriver press each hook down to release the clock. Then pull out to unsnap bottom hinges. 4 x 4 and 4 x 6: From the top of the bracket, insert a thin screwdriver into each notch and gently move the screwdriver sideways to unlock the clock. Then pull clock forward and up to unsnap. Lift out. Figure 14: Remove Clock from Bracket Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 23
24 Dual-mount Digital Clock/Timer Installation - Levo Series A Dual-mount Digital Clock consists of two single-sided digital clocks and a bracket kit. The kit contains a flange (piece that mounts to ceiling or wall), a bracket (piece that bolts to flange and to which two clocks are mounted), and the hardware necessary to complete the installation. Using the kit, you combine the two single-sided digital clocks to create a dual clock. NOTE: The two clocks function independently of each other, requiring each clock s settings to be configured separately. Upon applying power to the digital clock/timer or when pressing the Reset button located in the setting panel, the clock initiates its power up sequence as described below. 1. All 8 LED segments display 8 s with a red dot on the bottom right of each of the two hour digits and one at the second or last minute digit. 2. All LED segments display dashes and then dashes with a colon between the hours and minutes. 3. Once the clock/timer receives a signal from the transmitter, the LED segments display the time received from the transmitter s time source and a flashing red dot appears at the bottom right of the second hour digit for three minutes. Materials Supplied Two single-sided digital clocks Flange: mounts to ceiling or wall Bracket: bolts to flange and to which two clocks are mounted Hardware necessary to complete the installation Materials Required (Not Supplied) One junction box Install Dual-mount Digital Clock/Timer 1. On the wall or ceiling, measure and drill holes with the correct spacing to mount the flange over the junction box, as shown in Figure Attach the flange to the wall or ceiling using the toggle anchors and the longer machine screws provided. NOTE: If wall mounting to location outside of the junction box, break off or cut openings in flange to route power cords. 3. Attach the bracket to the flange using the shorter machine screws, nuts, and washers provided. 4. For wall mount only, knock out power cord break. 5. Wire clocks to main power, using cord retaining clips to dress wires. 6. Align the clock to the bracket hooks and hinges and snap into place. Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 24
25 Figure 15: Dual Digital Bracket Kit Flange Dimension Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 25
26 Figure 16: Dual Digital Clock Mounting Illustration Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 26
27 Dual-Mount Dimension Specifications Clock Type No. Digits Width from Wall (A) Height from Ceiling (B) Depth of Two Clocks (C) Dual 2.5" (6.4 cm) 6-digit 16.8" (42.7 cm) 8.0" (20.3 cm) 5.9" (15 cm) Dual 2.5" (6.4 cm) 4 digit 13.8" (35.1 cm) 8.0" (20.3 cm) 5.9" (15.0 cm) Dual 4" (10.16 cm) 4-digit 20.9" (53.1 cm) 11.0" (27.9 cm) 6.3" (16.0 cm) Dual 4" (10.16 cm) 6 Digit 26.3" (66.8 cm) 11.0" (27.9 cm) 6.3" (16.0 cm) Figure 17: Dual Mount Dimension Illustration Remove Dual-Sided Digital Clock from Mounting Bracket 2.5 x 4 and 2.5 x 6: From the top of the bracket, using a screwdriver press each hook down to release the clock. Then pull out to unsnap bottom hinges. 4 x 4 and 4 x 6: From the top of the bracket, insert a thin screwdriver into each notch and gently move the screwdriver sideways to unlock the clock. Then pull clock forward and up to unsnap. Lift out. Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 27
28 Flush-mount Clock/Timer Installation - Levo Series Complete the steps below to install a flush-mount digital clock/timer to either a new or existing wall surface. Supplied Materials The following parts are supplied with the clock/timer. (1) Flush-mount Junction Box. Material: ABS plastic, Color: black, UL Rated 94-V0 (1) Bezel. Material: ABS plastic, Color: black, UL Rated 94-V0 (4) #10 Phillips Flat Head Screw (4) Drywall Anchors Installation Steps Complete the steps below to install a flush-mount digital/clock timer. 1. Mount flush-mount junction box. New Wall Surface: Mount the junction box to wall studs using four common drywall screws (not supplied), as shown in Figure 18. Remove the applicable conduit knockout(s) for the incoming AC-power and the timer input (required for timer models only). Do not remove knockouts that you will not be using. Existing Wall Surface: Cut a 14.4" (36.5 cm) wide x 5.8" (14.7 cm) high wall opening between two wall studs, as shown in Figure 19. Securely mount the junction box to all studs using four common drywall screws (not supplied) at each of the corner locations. Remove the applicable conduit knockout(s) for the incoming ACpower conduit and the timer input conduit (required for timer models only). Do not remove knockouts that you will not be using. 3. Connect conduit connection(s) to the junction box. NOTE: For timer models only, AC wiring is required to be located to the right side of the junction box divider and the timer input to the left side. 4. New Wall Surface only: Cut out a 14" (35.5 cm) wide x 5.25" (13.3 cm) high wall opening for placement of the clock assembly. Trim opening if necessary. 5. Gently snap the flush-mount bezel onto the front of the clock/timer. 6. Secure wiring and complete AC-power and timer input connections. 7. Insert clock assembly into wall opening. 8. Level clock assembly within wall opening and secure bezel to the wall surface using the four screws and anchors (supplied) at each of the corner locations. Upon applying power to the digital clock/timer or when pressing the Reset button located in the setting panel, the clock initiates its power up sequence as described below. 1. All 8 LED segments display 8 s with a red dot on the bottom right of each of the two hour digits and one at the second or last minute digit. 2. All LED segments display dashes and then dashes with a colon between the hours and minutes. Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 28
29 3. Once the clock/timer receives a signal from the transmitter, the LED segments display the time received from the transmitter s time source and a flashing red dot appears at the bottom right of the second hour digit for three minutes. Figure 18: New Wall Surface- Flush-mount Assembly Illustration Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 29
30 Figure 19: Existing Wall Surface - Flush-mount Assembly Illustration Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 30
31 Flush-Mount Dimension Specifications - Levo Series Clock Type Weight Max. Current Draw Width from Wall (A) Height Depth 2.5" (6.4 cm), 6- Digit 2.0 lbs. (0.9 kg) 230 ma 16.8" (42.7 cm) 6.5" (16.5 cm) 3.4" (8.6 cm) Figure 20: Flush-Mount Dimension Illustration Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 31
32 Remote Antenna Installation Digital Clocks and Timers with a remote antenna are shipped from the factory with a BNC cable attached to the clock/timer assembly. The remote antenna components are required to be assembled and mounted. Remote Antenna Components (1) Antenna (1) Mounting bracket (1) Straight connector (for standard, vertical mount) (1) Right-angle connector (for horizontal mount) (2) Screws for mounting bracket Optional components 16.5 feet (5 meter) cable extension with BNC adapter Assemble Remote Antenna 1. For vertical mount, connect the BNC cable adapter to the straight connector. For horizontal mount, remove the straight connector and connect the BNC cable adapter to right-angle connector. Push the adapter onto the connector and turn connector 1/4 turn to lock into place. NOTE: Antenna is required to be in a vertical position. 2. Connect the antenna to the other end of connector. 3. Use the two screws to securely mount bracket to wall surface. Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 32
33 Mount Remote Antenna The length of the BNC cable can be increased by adding cables and adapters up to a maximum recommended length of 45 feet (13.7 meter). The cable can be placed in any position, but the antenna must be mounted vertically and away from metal objects. Unless it is very close to the transmitter, the powered clock will not set to the correct time without the remote antenna connected. If the remote antenna is to be mounted several centimeters above the clock and if the antenna cable is to be concealed behind the wall, use a single gang electrical box to be mounted horizontally behind the clock. For a straight vertical cable run, a minimum of 0.5 in. (1.27 cm) electrical conduit should be used, coupled with the top side of the electrical box. If a 16.5 feet (5 meter) cable extension is used and the intent is to keep as much cable concealed as possible, connect the extension to the standard antenna cable prior to running the cable into the conduit. For a concealed cable run, a 0.5 in. (1.27 cm) hole in the wall will need to be made close to where the remote antenna bracket will be mounted. The antenna cable BNC plug has a straight vertical mate with the remote antenna bracket. Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 33
34 Timer Control Switch Installation - Levo Series Digital Elapsed Timers and Code Blue Timers include a Timer Control Switch that controls the timer functions. Installation Requirements (1) Timer control switch (supplied) (1) Cable connector (supplied). Cable is a 15 feet (4.6 meter) reversed wire (cross-pinned) telephone cable with an RJ-11 connector. The cable length can be extended up to 100 feet (30.4 meter). Required to connect timer control switch to timer unit. (1) Single-gang junction box (not supplied). Recommend use of a 2¼ in. x 2¾ in. x 4 in. (5.72 cm x 6.99 cm x cm) junction box. To Install Timer Control Switch 1. Wire the code blue timer input to the code blue system. Wiring is determined by the code blue system as specified below. Code blue systems that apply a voltage to start a code blue event: wire the timer 4 pin connector's RED (Positive Code Blue Input) and BLACK (Negative Code Blue Input) wires to the code blue system. Cap off the WHITE and GREEN wires separately. An input voltage of 5-120V (AC or DC) can be used. When using DC, be sure to use the correct polarity; RED wire is positive and the BLACK wire is ground. Code Blue start and stop events are triggered by the application of voltage across the code blue input wires. Code blue systems that use a dry contact and do not inject a voltage: wire the timer 4 pin connector's GREEN (Ground) and BLACK (Negative Code Blue Input) wires together and wire the WHITE (12VDC) and RED (Positive Code Blue Input) wires to the code blue system dry contact. 2. Connect the timer control switch to the timer using the supplied cable. 3. Securely mount the timer control switch into a single-gang junction box. NOTE: The timer control switch membrane and wall plate may be cleaned with water or most common disinfectants. Be sure to test any cleaning solutions on a small area. Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 34
35 Figure 21: Timer Control Switch Wiring Specifications Figure 22: Timer Control Switch Installation Specifications Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 35
36 DIGITAL CODE BLUE TIMER AND ELAPSED TIMER OPERATION The Code Blue Timer is a multifunction digital clock and timer that integrates with an existing facility Code Blue system to effectively time each event. When a Code Blue event is invoked, a relay/pulse is sent from the Code Blue system to the timer, which triggers it to begin counting up. If a Code Blue status is in effect, it will take priority and the timer s previous task will run in the background until the Code Blue function is stopped. A switch control allows the user to operate the timer in multiple modes. In the event of a power outage, the timer's memory will maintain the correct time for a minimum of 1 hour without power. A Digital Elapsed Timer accurately counts up or counts down to a maximum of 99 hours, 59 minutes, and 59 seconds, and then capture and store event data for report generation. A switch control allows the user to run, hold, or reset the timer when in elapsed or count down timer mode. When not in the elapsed timer mode, synchronized time is displayed. Timer Switch Control Elapsed Timer function is triggered by the use of the switch control; allowing a user to run, hold, or reset the timer events. Code Blue Timer function is triggered by the input of the wired connection to the code blue system and the use of the switch control allows a user to halt a code blue event. Designed to fit inside a single gang box (not supplied); typically in. x in. x 4 in. (11.45 cm x 6.99 cm x cm) Timer Switch Control can simultaneously activate two connected timers for even more accurate time management Membrane switch and wall plate clean easily and resist common cleaners and disinfectants. Be sure to test any cleaning solutions on a small area Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 36
37 Code Blue Timer Operation Upon receiving a code blue system input, the clock immediately enters code blue mode and starts counting up from 00:00:00. Upon reaching 99:59:59, the code blue timer will beep for 3 seconds. Code blue mode is indicated by the colon, dash and decimal points not being lit (in both viewing and counting modes). Any other counting events remain operational in the background. Time duration of the last code blue event is stored in memory, and can be viewed until a new code blue event is triggered. A code blue count can be halted by pressing the STOP/START button. Pressing either DISPLAY or RESET is ignored while in code blue mode. Triggering of the code blue input while a current code blue is counting will be ignored. Code Blue Count Mode Code Blue Count Mode Operating Specifications Pressing the button... Running Mode Halted Mode DISPLAY Ignored Places display back in clock mode EXIT Holding down DISPLAY for a minimum of four seconds shows the last code blue time. RESET SET/CHANGE Ignored Ignored STOP/START INCREMENT Halts the code blue count at the moment the button is pressed Ignored NOTE: If the code blue counter reaches 99:59:59, the counter will stop. Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 37
38 Elapsed Timer Operation The timer has two states: Normal State: Controls the operation of the timer and is the text labeled on the top of the switch control buttons. For additional information, see "Normal State - Timer Mode" located on page 38. Set State: Controls the setup of the timer and is the text labeled on the bottom of the switch control buttons. For additional information, see "Set State - Timer Mode" located on page 39. Normal State - Timer Mode The Normal State consists of three modes: clock, count-up, and count-down. In this state, the text labeled on the top of the switch control buttons are applicable (DISPLAY, STOP/START, RESET). Table 3: Normal State Operation Display Specifications Clock Mode Count-Up Mode Count-Down Mode LED Display 10:45 02 Displays current time 0.0:00 00 Decimal lit after the 10hr digit 99: Decimal lit after the 1 sec digit Table 4: Normal State Operation Specifications Pressing the button... Clock Mode Count-Up Mode Count-down Mode DISPLAY EXIT Pressing DISPLAY scrolls through the various modes in the following order: 1. Clock Mode 2. Count-Up Mode 3. Count-Down Mode STOP/START INCREMENT Ignored Controls the up counter while in count-up mode. If the counter is stopped, pressing the STOP/START button starts the counter. If the counter is started, pressing the STOP/START button stops the counter. Controls the down counter while in count-down mode. If the counter is stopped, pressing the STOP/START button starts the counter. If the counter is started, pressing the STOP/START button stops the counter. Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 38
39 Pressing the button... Clock Mode Count-Up Mode Count-down Mode RESET SET/CHANGE Ignored Pressing the RESET button once automatically stops and resets the up counter to its preset time (pause). Or Holding the RESET button puts the time into SET STATE. Pressing the RESET button once automatically stops and resets the down counter to its preset time (pause). Or Holding the RESET button puts the time into SET STATE. Set State - Timer Mode The Set State is used to set the count-up start time and the count-down start time. Enter Set State by holding the RESET button while in count-up or count-down mode. In this state: The text labeled on the bottom of the switch control button is applicable (SET/CHANGE, INCREMENT, EXIT). The dash, colon, and decimal points are not displayed. The digit that is currently being set will flash. Table 5: Set State Operating Specifications Pressing the button... Start Count-Up Mode Start Count-Down Mode DISPLAY EXIT Exits Set State Exits Set State STOP/START INCREMENT Increments the selected digit Increments the selected digit RESET SET/CHANGE Holding the SET/CHANGE button for 3 seconds enters the set mode, which is indicated by : on the display. The selected digit will blink. Pressing SET/CHANGE again to select the next digit. Holding the SET/CHANGE button for 3 seconds enters the set mode, which is indicated by : on the display. The selected digit will blink. Pressing SET/CHANGE again to select the next digit. Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 39
40 DIGITAL PROGRAMABLE TIMER OPERATION The Programmable Countdown Timer counts down in minutes and seconds at a predefined schedule of timed events from 1 minute to 99 minutes 59 seconds. The countdown schedule and events are configured and managed using the Primex Wireless Event Scheduler Pro Software and the schedule is downloaded to the system transmitter. For details on using the software, please see the Event Scheduler Pro User Guide. The timer will begin counting down at each preset time on schedule. When each countdown function is complete the timer automatically displays the correct time, synchronized to every other clock on your Primex Wireless XR 72MHz/GPS system. The Programmable Countdown Timer functions in much the same way as a standard digital clock. Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 40
41 SUPPORT Primex Wireless Technical Support Technical Support responds to specific questions about product features, system configuration, and troubleshooting. All support services will be delivered in accordance with your organization's support agreement and warranties. Before contacting Technical Support, make sure you have satisfied the system requirements that are listed in your product documentation. Also, you should be at the computer on which the problem occurred, in case it is necessary to replicate the problem. When you contact Technical Support, please have the following information available: Customer ID Problem description Device hardware information Error messages Troubleshooting performed Recent network changes Contact Technical Support Available Monday through Friday, 7 AM to 7 PM CST (excluding holidays) To reach our support team, call , and press: Option 1: 72MHz/GPS Clock Systems, Transmitters and Bell Systems Option 2: SNS Network-based Clocks, Bells, Sensors and Software Option 3: OneVue Software, Sensors, Clocks, and Bell Scheduling Option 4: Primex Wireless Customer Service Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 41
42 WARRANTY One Year Limited Warranty Primex Corporation warrants this product to be free from defects in materials and workmanship for a standard of one year from the date of purchase. Primex will at its sole option, repair or replace any components that fail in normal use. Such repairs or replacements will be made at no charge to the customer for replacement parts. The customer will be responsible for any transportation costs. This warranty does not cover failures due to misuse, abuse, accidental or unauthorized alterations or repairs. The warranties and remedies contained herein are exclusive and in lieu of all other warranties express or implied or statutory, including any liability arising under any warranty or merchantability or fitness for a particular purpose, implied, statutory or otherwise. In no event shall Primex be liable for any incidental, special, indirect or consequential damages, whether resulting from the use, misuse or inability to use this product or from defects in the product. Some states do not allow this exclusion or limitation of incidental or consequential damages so the above limitations or exclusion may not apply to you. To obtain warranty service: If after following the instructions in the product guide, you are certain the product is defective, please contact Primex Wireless Technical Support to assist with troubleshooting the issue. If the issue cannot successfully be resolved and the product is under warranty, an RMA (Return Material Authorization) will be generated. The RMA form will be provided via with detailed instructions for the return. All merchandise returned must be shipped to Primex Wireless, Attn: Returns Dept., N3211 County Road H, Lake Geneva, WI Primex Wireless retains the exclusive right to repair or replace the unit at its sole discretion. All merchandise returned must be shipped to Primex Wireless, Attn: Returns Dept., N3211 County Road H, Lake Geneva, WI Primex Wireless retains the exclusive right to repair or replace the unit at its sole discretion. Such shall be your sole exclusive remedy for any breach of warranty. Primex Wireless Levo Series Digital Clocks/Timers Installation Guide 42
Primex Wireless, Inc. July, Wells Street Lake Geneva, WI
Division 0 0 0 0 Primex Wireless, Inc. July, 00 Wells Street Lake Geneva, WI 00--0 www.primexwireless.com Product Guide Specification Specifier Note: This product specification is written according to
More informationMWT-FM. Operation Manual. FM Single Channel Transmitter. man_mwtfm.
MWT-FM FM Single Channel Transmitter Operation Manual man_mwtfm www.myeclubtv.com CONTENTS FCC COMPLIANCE STATEMENT. 3 INDUSTRY CANADA COMPLIANCE 3 MWT-FM ORIENTATION. 4 SAFETY PRECAUTIONS 5 FINDING FM
More informationIn-Wall Control Mount for ipod Touch
In-Wall Control Mount for ipod Touch INTRODUCTION The Mirage KP-iOS is an in-wall system that allows ipod touch (4th generation) to become a semi-permanent fixture in your wall. The system allows you to
More informationElectric Motorized Projection Screen Spectrum Series
Electric Motorized Projection Screen Spectrum Series User s Guide 1 Important Safety & Warning Precautions Make sure to read this user s guide and follow the procedure below. Caution: The screen s Black
More informationVNS2200 Amplifier & Controller Installation Guide
VNS2200 Amplifier & Controller Installation Guide VNS2200 Amplifier & Controller Installation 1. Determine the installation location for the VNS2200 device. Consider the following when determining the
More informationIn-Ceiling Electric Motorized Front Projection Screen Evanesce Series. User s Guide
In-Ceiling Electric Motorized Front Projection Screen Evanesce Series User s Guide Important Safety & Warning Precautions Make sure to read this user s guide and follow the procedures below. Caution: The
More informationKODAK Video Monitor CFH-V10
Quick Start Guide CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED
More informationBy CHANNEL VISION. Flush Mount Amplifier A0350
Spkrs Local In IR In 24VDC A0350 10 The A0350 can be used with Channel Vision s CAT5 audio hubs to provide a powerful 50Watts per channel in the listening zone. Alternatively, the A0350 can be added to
More informationUSER S MANUAL. Save this manual for future reference. For a digital version of this manual, visit
TM USER S MANUAL Save this manual for future reference. For a digital version of this manual, visit www.mylifter.com/installation. 4 5 TABLE OF CONTENTS 4 INSTALLING THE PULLEY SYSTEM FOR LIFTING 100
More information900-Lumen Portable LED Projector Part #: User manual
900-Lumen Portable LED Projector Part #: 21797 User manual 900-Lumen LED Projector Manual Page 2 of 14 900-Lumen LED Projector Manual Page 3 of 14! SAFETY WARNINGS AND CAUTIONS WARNING: To reduce the risk
More informationOperation Manual VMS 3.0 Video System
Operation Manual VMS 3.0 Video System for the AlterG Anti-Gravity Treadmill 1 This manual covers operation procedures for the following AlterG products: AlterG Video System model VMS 3.0 NOTE: The following
More informationWID-DL74 WID-DL74 BLP WID. Designed for. Installation guide for workitdesk interactive table for. BrightLink Pro
WID-DL74 WID-DL74 BLP WID Designed for BrightLink Pro Installation guide for workitdesk interactive table BrightLink Pro for Mounting the table unit 1 Unpack boxes 1 of 4 (Mobile base) and 2 of 4 (Motorized
More informationElectric Wall/Ceiling Projection Screen Saker Tab-Tension Series User s Guide
Electric Wall/Ceiling Projection Screen Saker Tab-Tension Series User s Guide Important Safety & Warning Precautions Make sure to read this user s guide and follow the procedures below. Caution: The screen
More informationElectric Motorized Projection Screen PowerMax Tension Series
Electric Motorized Projection Screen PowerMax Tension Series User s Guide Important Safety & Warning Precautions Make sure to read this user s guide and follow the procedures below. Caution: The screen
More informationSBL /SBLG Series Wireless Clock
Installation Manual V8.3 SBL /SBLG Series Wireless Clock Current as of August 2018 The Sapling Company, Inc. SBL and SBLG Series Wireless Clocks Table of Contents Table of Contents 2 Important Safety Instructions
More informationALPHA Personal Priority Display User Manual
ALPHA Personal Priority Display User Manual PERSONAL PRIORITY DISPLAY 1997 Adaptive Micro Systems Form No. 9708-5002 12/10/97 i NOTE: Due to continuing product innovation, specifications in this document
More informationAITech ProA/V Media Extender 5GHz Digital
AITech ProA/V Media Extender 5GHz Digital 5 GHz Wireless Digital Media Transmitter and Receiver User Manual Table of Contents 1. Package Contents 2. Panels and Functions AV Sender AV Receiver 3. Setup
More informationElectric Wall/Ceiling Projection Screen Saker Series User s Guide
Electric Wall/Ceiling Projection Screen Saker Series User s Guide Important Safety & Warning Precautions Make sure to read this user s guide and follow the procedures below. Caution: The screen s Black
More informationTV Lift System Model CL-65 Installation Instructions
TV Lift System Model CL-65 Installation Instructions Contact: Support@Nexus21.com Toll Free: (866) 500-5438 Phone: (480) 951-6885 Fax: (480) 951-6879 Revised: 01/17/17 Below is a parts list describing
More informationInstallation Manual SaVi Note Underwater LED Light
Installation Manual SaVi Note Underwater LED Light Model Numbers SAVI-NOTE7, SAVI-NOTE0 Table of Contents Safety Precautions...2 SaVi Note Install Instructions...3- M Instructions...- Warnings READ AND
More informationLIGHT COPILOT II. elationlighting.com Internet:
LIGHT COPILOT II E-mail: info@ elationlighting.com Internet: http://www.elationlighting.com 1 Introduction Thank you for your purchase of the LIGHT COPILOT II. The LIGHT COPILOT II is an intelligent lighting
More informationValcom Wired Digital Clock
Installation Manual V10.5 Valcom Wired Digital Clock V-D11025B, V-D11040B, V-D2425B, V-D2440B, V-2425B-6, and V-D2440B-6 Current as of February 2017 Valcom, Inc. Valcom Digital Series 2-Wire and 3-Wire
More informationVNS2210 Amplifier & Controller Installation Guide
VNS2210 Amplifier & Controller Installation Guide VNS2210 Amplifier & Controller Installation 1. Determine the installation location for the VNS2210 device. Consider the following when determining the
More informationTAC1 Telephone Entry System
TAC1 Telephone Entry System 1 4 7 2 3 5 6 8 9 0 INSTALLATION MANUAL For more information: www.devancocanada.com or call toll free at 855-931-3334 SPECIFICATIONS >> CABLE REQUIREMENTS, DIMENSIONS AND CARTON
More informationDISH Pro Hybrid 42 Switch Installation Guide
DISH Pro Hybrid 42 Switch Installation Guide VideoPath DISH PRO HYBRID SWITCH MODEL DPH42 209929 MMTTVV-FMYYXXXXX Made in XXX RECEIVER SATELLITE IN Power Inserter 12.5-29V 1825mA Safety Information Warning
More informationA. Section Includes: Division 1 applies to this section. Provide GPS wireless clock system, complete.
SPECIFICATIONS GPS Wireless Clock System Section 16730 TIME SYSTEM PART 1 - GENERAL 1.01 SUMMARY A. Section Includes: Division 1 applies to this section. Provide GPS wireless clock system, complete. B.
More informationModel 6527 & 6827 Single Line Scoreboard Owner s Manual
Model 6527 & 6827 Single Line Scoreboard Owner s Manual Portatree Eliminator 2000 Compatible Rev C RaceAmerica Corp. 280 Martin Ave. Unit#1 Santa Clara, CA 95050 (408) 988-6188 www.raceamerica.com info@raceamerica.com
More informationACCESSORIES MANUAL PART NUMBER: PRODUCT REVISION: 1 TNP100. Tilt N Plug Interconnect Box USER'S GUIDE
MANUAL PART NUMBER: 400-0091-001 PRODUCT REVISION: 1 TNP100 Tilt N Plug Interconnect Box USER'S GUIDE INTRODUCTION Your purchase of the TNP100 Tilt N Plug Interconnect Box is greatly appreciated. We are
More informationCR-R880-BL: Indoor/Outdoor Proximity Reader with 10cm (4in) read range
CR-R880-BL: Indoor/Outdoor Proximity Reader with 10cm (4in) read range Installation Manual Table of Contents Basic Operation...2 CR-R880-BL Block Diagram...2 Technical Specifications...3 Features...4
More informationINSTALLATION GUIDE. Axle Weighing Truck Scale. 60,000 lb x 20 lb Factory Calibrated Includes Pre-interfaced Wireless Remote LED Scoreboard Displays
INSTALLATION GUIDE 60,000 lb x 20 lb Factory Calibrated Includes Pre-interfaced Wireless Remote LED Scoreboard Displays V 1.0 OVERVIEW TOOLS REQUIRED Forklift and block Prybar Wrenches: #8 allen wrench,
More informationMonoBright LED DAYLIGHT 750
MonoBright LED DAYLIGHT 750 USER MANUAL MonoBright LED Daylight 750 - USER MANUAL 1 MonoBright LED DAYLIGHT 750 INTRODUCTION Thank you for choosing Genaray. The Genaray MonoBright LED Daylight 750 incorporates
More informationTIMETRAX SYNC RF WIRELESS DIGITAL CLOCK Installation Instructions
Installation Instructions OVERVIEW Thank you for choosing a TimeTrax Sync RF Wireless Clock System. The TimeTrax RF Wireless Clock System receives dependable, accurate time from the TimeTrax Sync RF Wireless
More informationUser Instructions. 16 SCB Sync Station.
User Instructions 16 SCB Sync Station Contents Overview... 1 Specifications... 1 Compliance and approvals... 2 Safety instructions... 3 Set up... 4 How to charge multiple devices... 4 How to synchronize
More informationSprite TL Quick Start Guide
Sprite TL Quick Start Guide with 115 VAC Power Cord and 4-Conductor Signal Cable Reference Manual Sprite TL Online and downloadable Product Manuals and Quick Start Guides are available at www.hydrosystemsco.com
More informationThank you for purchasing SEIKO SHOOTING TIMER KT-401. Before using your SEIKO SHOOTING TIMER, please read this manual carefully for its proper use
紙 Thank you for purchasing SEIKO SHOOTING TIMER KT-401. Before using your SEIKO SHOOTING TIMER, please read this manual carefully for its proper use and care. Keep this manual handy for ready reference.
More informationI1000M Rough-In Instructions
I1000M Rough-In Instructions Thank you for purchasing an Intrasonic Technology product. Our products are built to provide you with years of high quality sound. If you need assistance with the installation
More informationIndoor/Outdoor Security System with Quad Monitor User s Manual
Indoor/Outdoor Security System with Quad Monitor User s Manual 4919539 Important! Please read this booklet carefully before installing or using these units. WARNING - These units should ONLY be opened
More informationFor use with QED and hardwired control panels ONLY!
K3129-5 10/98 6128WL Keypad/Receiver INSTALLATION INSTRUCTIONS For use with QED and hardwired control panels ONLY! General Information The 6128WL Keypad/Receiver is a combination unit. It replaces a 6128
More informationINSTALLATION INSTRUCTIONS FOR
INSTALLATION INSTRUCTIONS FOR MODEL 2240LED www.sportablescoreboards.com 1 Table of Contents 8 X 7 INDOOR SCOREBOARD... 3 THE SCOREBOARD SYSTEM SHOULD INCLUDE THE FOLLOWING PARTS:... 3 INSTRUCTIONS FOR
More informationUser Guide. HDMI Fiber Optic Extender. DVI-7350a
User Guide HDMI Fiber Optic Extender DVI-7350a Table of Contents Section Page Product Safety.................................... 1 1.0 Introduction...2 2.0 Specifications...3 3.0 Package Contents...3 4.0
More informationUser s Guide. 5.8GHz Wireless A/V Signal Sender
1500332 User s Guide 5.8GHz Wireless A/V Signal Sender Thank you for purchasing your A/V Signal Sender from RadioShack. Please read this user s guide before installing, setting up, and using your new sender.
More informationStarling Tab-Tension 2 Series
Electric Wall/Ceiling Projection Screen Starling Tab-Tension 2 Series For: Spectra White FG and CineGrey 5D User s Guide Important Safety & Warning Precautions Make sure to read this user s guide and follow
More informationVT VGA TFT NEMA 4/12 Flat Panel Monitor. User s Guide
VT1040 10.4 VGA TFT NEMA 4/12 Flat Panel Monitor User s Guide 301040(A) (was document no. 920A0001 version 1.1), revised 01/98 Viewtronix Viewtronix reserves the right to make changes in specifications
More informationDoorphone Video Intercom
HOME SERIES INSTRUCTION MANUAL Doorphone Video Intercom with Colour 4.3 LCD Monitor EN Getting to know your LCD Screen (Front) 1 2 3 4 5 6 1) LCD Screen - This is where you view your visitor that the intercom
More informationImportant Safety & Warning Precautions
Electric Motorized Projection Screen VMAX 2 Series User s Guide Important Safety & Warning Precautions Make sure to read this user s guide and follow the procedure below. Caution: The screen s Black Top
More informationPower Injector 1520 Series
Power Injector 1520 Series Technical Specifications Input voltage 100 to 240 VAC Output voltage 56.0 VDC Voltage range tolerance 54 VDC to 57 VDC Maximum current 1.43 A No load current 15 ma 56VDC@0.71A
More informationACCESSORIES MANUAL PART NUMBER: TNP500. Universal Tilt N Plug Interconnect Box USER'S GUIDE
MANUAL PART NUMBER: 400-0091-003 TNP500 Universal Tilt N Plug Interconnect Box USER'S GUIDE INTRODUCTION Your purchase of the TNP100 Tilt N Plug Interconnect Box is greatly appreciated. We are sure you
More informationREAD ME FIRST. Touchstone TV Lift
Whisper Lift II PRO 2 READ ME FIRST 1. After completing the unpacking and uncrating of the cabinet, you will find the Owner s Manual, TV, installation hardware, and the wireless remote all together and
More informationMonoBright LED DAYLIGHT 1200
MonoBright LED DAYLIGHT 1200 USER MANUAL MonoBright LED Daylight 1200 - USER MANUAL 1 MonoBright LED DAYLIGHT 1200 INTRODUCTION Thank you for choosing Genaray. The Genaray MonoBright LED 1200 incorporates
More informationHTP1502W1 Remote Controlled Multicolor Lighting System
Page 1 of 8 CHATSWORTH, CALIFORNIA 91311 USA www.cyron.com HTP1502W1 Remote Controlled Multicolor Lighting System Thank you for purchasing CYRON HTP1502W1 LED Lighting System. This system will bring the
More informationOWNERS MANUAL. Revision /01/ Lightronics Inc. 509 Central Drive Virginia Beach, VA Tel
OWNERS MANUAL Revision 1.8 09/01/2002 OWNERS MANUAL Page 2 of 12 AR-1202 UNIT DESCRIPTION The AR-1202 consists of a processor and 12 dimmer channels of 2.4KW each. Each dimmer channel is protected by a
More information2013, 2014 Hewlett-Packard Development Company, L.P.
User Guide 2013, 2014 Hewlett-Packard Development Company, L.P. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
More informationST8-WiFi Timer. Installation Guide and Operations Manual. English MIN M D YYYY
ST8-WiFi Timer Installation Guide and Operations Manual AM M D YYYY English Contents ST8-WiFi Timer Installation Guide and Operations Manual Introduction Welcome to Rain Bird... 1 Timer Features... 1 Controls
More informationAES-402 Automatic Digital Audio Switcher/DA/Digital to Analog Converter
Broadcast Devices, Inc. AES-402 Automatic Digital Audio Switcher/DA/Digital to Analog Converter Technical Reference Manual Broadcast Devices, Inc. Tel. (914) 737-5032 Fax. (914) 736-6916 World Wide Web:
More informationSR - 516D DESK TOP DMX REMOTE STATION. Version: Date: 05/16/2013
SR - 516D DESK TOP DMX REMOTE STATION Version: 1.10 Date: 05/16/2013 Page 2 of 10 TABLE OF CONTENTS DESCRIPTION 3 POWER REQUIREMENTS 3 INSTALLATION 3 CONNECTIONS 3 POWER CONNECTIONS 3 DMX CONNECTIONS 3
More informationUSER MANUAL. 22" Class Slim HD Widescreen Monitor L215DS
USER MANUAL 22" Class Slim HD Widescreen Monitor L215DS TABLE OF CONTENTS 1 Getting Started Package Includes Installation 2 Control Panel / Back Panel Control Panel Back Panel 3 On Screen Display 4 Technical
More informationDISTRIBUTION AMPLIFIER
MANUAL PART NUMBER: 400-0045-005 DA1907SX 1-IN, 2-OUT VGA/SVGA/XGA/UXGA DISTRIBUTION AMPLIFIER USER S GUIDE TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS... 2 GENERAL...2 GUIDELINES FOR RACK-MOUNTING...2
More informationPLL2210MW LED Monitor
PLL2210MW LED Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Safety Precautions...2 First Setup...3 Front View of the Product...4 Rear View of the Product...5 Quick Installation...6
More informationSyncGen. User s Manual
SyncGen User s Manual 1 IMPORTANT SAFETY INSTRUCTION READ FIRST This symbol, whenever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure-voltage that may be sufficient
More informationUser Manual. AtlonA. Passive VGA Extender with Wall Plate or Box options up to 330ft over 1 x CAT5/6/7 Cable AT-VGA100-SR and AT-WPVGA-SR AT-WPVGA-SR
User Manual AtlonA Passive VGA Extender with Wall Plate or Box options up to 330ft over 1 x CAT5/6/7 Cable AT-VGA100-SR and AT-WPVGA-SR AT-WPVGA-SR Receiver Transmitter AT-VGA100-SR Receiver Transmitter
More informationMaster Clock Controller. User Guide. pyramidtimesystems.com
Master Clock Controller User Guide pyramidtimesystems.com TABLE OF CONTENTS TABLE OF CONTENTS... PRODUCT OVERVIEW... FEATURES... 3 CONTENTS... 4 WALL MOUNTING... 5 INSTALLATION... 6 PROGRAMMING... 7-8
More informationAWT150C/AWT150CS/ AWT151C CCD Camera
AWT150C/AWT150CS/ AWT151C CCD Camera ISSUED OCTOBER 2018 WARNING Failure to follow all instructions and safety precautions in this manual, in the vehicle and body manufacturers' manuals and on the safety
More informationRD RACK MOUNT DIMMER OWNERS MANUAL VERSION /09/2011
RD - 122 RACK MOUNT DIMMER OWNERS MANUAL VERSION 1.3 03/09/2011 Page 2 of 14 TABLE OF CONTENTS UNIT DESCRIPTION AND FUNCTIONS 3 POWER REQUIREMENTS 3 INSTALLATION 3 PLACEMENT 3 POWER CONNECTIONS 3 OUTPUT
More informationMaster Clock Controller. User Guide. pyramidtimesystems.com
Master Clock Controller User Guide pyramidtimesystems.com TABLE OF CONTENTS TABLE OF CONTENTS... PRODUCT OVERVIEW... FEATURES... 3 CONTENTS... 4 WALL MOUNTING... 5 INSTALLATION... 6 PROGRAMMING... 7-8
More informationINSTALLATION INSTRUCTIONS FOR. MODEL 2230LED
INSTALLATION INSTRUCTIONS FOR MODEL 2230LED www.sportablescoreboards.com 1 Table of Contents MODEL 2230LED... 3 8 X 4 INDOOR SCOREBOARD... 3 THE SCOREBOARD SYSTEM SHOULD INCLUDE THE FOLLOWING PARTS:...
More informationVideoEase HDMI 3x1 Switcher Kit (110V) Installation Guide
VideoEase HDMI 3x1 Switcher Kit 500410 (110V) Installation Guide P/N: 94-00628-A SE-000627-A Copyright Notice : Copyright 2008 MuxLab Inc. All rights reserved. Printed in Canada. No part of this publication
More informationUSER S MANUAL. Deuce HD User's Manual WORLD HEADQUARTERS
USER S MANUAL WORLD HEADQUARTERS Artel Video Systems 5B Lyberty Way Westford, MA 01886 Tel: (978) 263-5775 Fax: (978) 263-9755 Email: info@artel.com Web: www.artel.com P/N 1219 Rev. F Copyright 2016 USER
More informationSite Installation Model MP-8433
Site Installation Model MP- Rev. //0 SCOREBOARD SITE INSTALLATION INSTRUCTIONS CAUTION: All American Scoreboards (AAS) recommends the sign be installed by a licensed contractor, and must meet all local
More informationHDMI Extender over UTP Cable
User Manual HDMI Extender over UTP Cable VHDE-300 Tx Rx Features.. Extends HDMI 1080p AV and IR Signals Transmission distance up to 60m/200ft via CAT6 cable or higher grade cable 5V DC, 1A Important Safety
More informationLINE DRIVERS MANUAL PART NUMBER: DA3000TM0 1-IN, 1-OUT COMPOSITE VIDEO + AUDIO LINE DRIVER TABLE MOUNT USER S GUIDE
MANUAL PART NUMBER: 400-0175-001 DA3000TM0 1-IN, 1-OUT COMPOSITE VIDEO + AUDIO LINE DRIVER TABLE MOUNT USER S GUIDE TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS... 2 GENERAL... 2 INSTALLATION...
More information2.4 GHz WIRELESS SURVEILLANCE SYSTEM
2.4 GHz WIRELESS SURVEILLANCE SYSTEM Operating Instructions Tested Comply With FCC Standards Model # TBM-18 BEFORE OPERATING THIS PRODUCT, READ, UNDERSTAND, AND FOLLOW THESE INSTRUCTIONS. Be sure to save
More informationGarmin GC 10 Marine Camera Instructions
Garmin GC 10 Marine Camera Instructions FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
More informationOperating Manual. Automated Gear. Apollo Design Technology, Inc Fourier Drive Fort Wayne, IN USA
Operating Manual Automated Gear Apollo Design Technology, Inc. 4130 Fourier Drive Fort Wayne, IN 46818 USA PH: +01(260)497-9191 FX: +01(260)497-9192 www.apollodesign.net 11-25-09 5-6 POWERING UP THE RIGHT
More informationTR6102HD HDTV/DVD/COMPONENT VIDEO TO RGBHV TRANSCODER USER S GUIDE
MANUAL PART NUMBER: 400-0031-003 PRODUCT REVISION: 1 HDTV/DVD/COMPONENT VIDEO TO RGBHV TRANSCODER USER S GUIDE INTRODUCTION Thank you for your purchase of the Transcoder. We are certain that you will find
More informationTroubleshooting CS800/LC900 Bikes
Troubleshooting CS800/LC900 Bikes CS800/900LC Bike Troubleshooting Entering the Maintenance Mode 15 Touch Screen: The Maintenance Mode is designed to help the tech determine certain faults in the upper
More informationLF-IRX. 12 Month Limited Warranty LF-IRX. Remote Control Extender. Owner s manual. For customer service and technical information::
12 Month Limited Warranty Audiovox Electronics Corporation (the company) warrants to the original purchaser of this product that should this product or any part thereof, under normal use and conditions,
More informationWDK-2500-STROBE. User Guide
WDK-2500-STROBE User Guide Warning: This device complies with Part 15 of the FCC rules, operation of this device is subject to the following conditions: 1. This device may not cause harmful interference.
More informationCHECK LINE. Model LS-36-LED. Stationary Stroboscope. Operating Manual BY ELECTROMATIC
CHECK LINE BY ELECTROMATIC Stationary Stroboscope Model LS-36-LED Operating Manual Table of Contents 1.0 Introduction... 02 1.1 Unpacking 1.2 Optional Accessories 2.0 Safety Information... 3 3.0 Controls...
More informationSCIR. Infrared Illuminator Powerful Indoor/Outdoor IR Spotlight SCIR
SCIR Infrared Illuminator Powerful Indoor/Outdoor IR Spotlight The NetMedia SCIR Infrared (IR) Illuminator provides night vision for IR (850nm) sensitive cameras. It enables cameras such as NetMedia s
More informationModel#: IN-MDRI3MF. Hardware User Manual. 3MP Indoor Mini Dome with Basic WDR, Fixed lens. (PoE) Ver. 2013/02/04
Model#: IN-MDRI3MF 3MP Indoor Mini Dome with Basic WDR, Fixed lens Hardware User Manual (PoE) Ver. 2013/02/04 Table of Contents 0. Precautions 3 1. Introduction 4 Package Contents... 4 Features and Benefits...
More informationUser Guide. Single-Link DVI Active Cable Extender. DVI-7171c
User Guide Single-Link DVI Active Cable Extender DVI-7171c TABLE OF CONTENTS SECTION PAGE PRODUCT SAFETY...1 PRODUCT LIABILITY...1 1.0 INTRODUCTION...2 2.0 SPECIFICATIONS...3 3.0 PACKAGE CONTENTS...4 4.0
More informationAES-404 Digital Audio Switcher/DA/Digital to Analog Converter
Broadcast Devices, Inc. AES-404 Digital Audio Switcher/DA/Digital to Analog Converter Technical Reference Manual Broadcast Devices, Inc. Tel. (914) 737-5032 Fax. (914) 736-6916 World Wide Web: www.broadcast-devices.com
More informationINSTALLATION INSTRUCTIONS MODEL VSBX-236 LED 3 X 8 INDOOR SCOREBOARD
1 INSTALLATION INSTRUCTIONS MODEL VSBX-236 LED 3 X 8 INDOOR SCOREBOARD NOTE TO INSTALLERS: PLEASE RETURN THIS MANUAL TO THE INDIVIDUAL IN CHARGE OF THE SCOREBOARD UPON COMPLETION OF INSTALLATION. The scoreboard
More informationCOMPOSITE VIDEO (BNC) TO VGA VIDEO FORMAT CONVERTER AND SCALER AT-RGB110
User Manual COMPOSITE VIDEO (BNC) TO VGA VIDEO FORMAT CONVERTER AND SCALER AT-RGB110 TABLE OF CONTENTS 1. Introduction... 2 2. Package Contents... 2 3. Features... 2 4. Specification... 2 5. Panel Description...
More informationMaster Clock Controller. User Guide. pyramidtimesystems.com
Master Clock Controller User Guide pyramidtimesystems.com TABLE OF CONTENTS TABLE OF CONTENTS... PRODUCT OVERVIEW... FEATURES... 3 CONTENTS... 4 WALL MOUNTING... 5 INSTALLATION... 6 PROGRAMMING... 7-8
More informationPLL1920M LED LCD Monitor
PLL1920M LED LCD Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Safety Precautions...2 First Setup...3 Front View of the Product...4 Rear View of the Product...5 Installation...6
More informationSAFETY WARNINGS AND GUIDELINES... 3 INTRODUCTION... 4 CUSTOMER SERVICE... 4 PACKAGE CONTENTS... 4 RECOMMENDED TOOLS... 6 CONTROL PANEL OVERVIEW...
CONTENTS SAFETY WARNINGS AND GUIDELINES... 3 INTRODUCTION... 4 CUSTOMER SERVICE... 4 PACKAGE CONTENTS... 4 RECOMMENDED TOOLS... 6 CONTROL PANEL OVERVIEW... 6 ASSEMBLY... 7 SYSTEM RESET... 11 OPERATION...
More informationModel Extend HDMI audio and video connections up to 300 feet. Add up to 8 additional receivers with a dedicated network switch
HDMI Extender over Single CAT 6 Cable with IR Control Model 103002 Extend HDMI audio and video connections up to 300 feet Utilize existing Cat 6 wiring for an easy installation Add up to 8 additional receivers
More informationAS Telecommunication Watch Dog. Version 2.70
AS-2500-1 Telecommunication Watch Dog Version 2.70 Table of Content TABLE OF CONTENT...2 INTRODUCTION...3 FEATURES...3 INSTALLATION...3...3 Changing the maximum number of rings... 4 Verifying the maximum
More informationPL2410W LCD Monitor USER'S GUIDE.
PL2410W LCD Monitor USER'S GUIDE www.planar.com Content Operation Instructions...1 Safety Precautions...2 First Setup...3 Front View of the Product...4 Rear View of the Product...5 Quick Installation...6
More informationRA-RS232, RB-RS232. Setup and Installation Guide Addendum For RadioRA RS232 Interface
RA-RS232, RB-RS232 Setup and Installation Guide Addendum For RadioRA RS232 Interface A Comprehensive Step-by-Step Guide for Programming and Operating the Lutron RadioRA RS232 Interface Note: Please leave
More informationAE-341 SERIES PROCESS INDICATORS 2 TO 6 DIGITS 0-20 MA, 4-20 MA, 0-5V, OR 0-10V SCALED INPUT
FN: 341MAN1.DOC AE-341 SERIES PROCESS INDICATORS 2 TO 6 DIGITS 0-20 MA, 4-20 MA, 0-5V, OR 0-10V SCALED INPUT DESCRIPTION AE Series Process Indicators are available with 1", 2.3", 4", 8", or 12" high digits,
More informationHDMI WIRELESS EXTENDER/ RECEIVER. Vanco Part Number: HDWIRKIT HDWIR-RX. Technical Support
HDMI WIRELESS EXTENDER/ RECEIVER Vanco Part Number: HDWIRKIT HDWIR-RX Technical Support www.vanco1.com techsupport@vanco1.com 800-626-6445 DEAR CUSTOMER Thank you for purchasing this product. For optimum
More informationSite Installation Model MP-8424
Site Installation Model MP- Rev. //0 SCOREBOARD SITE INSTALLATION INSTRUCTIONS CAUTION: All American Scoreboards (AAS) recommends the sign be installed by a licensed contractor, and must meet all local
More informationInformation. Marketing Description. For Models: DA2133i. 2113i. User s Guide Rev B
Casework Model Number User s Marketing Description Information For Models: xxxx FCC (-001) (All) xxxx FTC (All) (-002) DA2133i 2113i User s Guide 003-1891-00 Rev B Table of Contents Important Information
More informationHDMI 5x1 Switch B-240-HDSWTCH-5X1 INSTALLATION MANUAL
HDMI 5x1 Switch B-240-HDSWTCH-5X1 INSTALLATION MANUAL IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of fire or electric shock, read and follow all instructions and warnings in this manual. Keep this
More informationMONOPRICE. BitPath AV SDI Wireless Transmitter & Receiver Kit, 200m. User's Manual P/N 16225
MONOPRICE BitPath AV SDI Wireless Transmitter & Receiver Kit, 200m P/N 16225 User's Manual SAFETY WARNINGS AND GUIDELINES Please read this entire manual before using this device, paying extra attention
More informationHOME THEATER. HDMI HDBaseT Lite Extenders. Vanco Part Number: Technical Support
HOME THEATER HDMI HDBaseT Lite Extenders Vanco Part Number: 280766 280767 Technical Support www.vanco1.com info@vanco1.com 800-626-6445 DEAR CUSTOMER Thank you for purchasing this product. For optimum
More informationUtility Amplifier GA6A Model
Utility Amplifier GA6A Model Installation and Use Manual 2004 Bogen Communications, Inc. All rights reserved. Specifications subject to change without notice. 54-5757-03D 1503 NOTICE: Every effort was
More informationElectric Motorized Projection Screen Spectrum Tab-Tension Series User s Guide
Electric Motorized Projection Screen Spectrum Tab-Tension Series User s Guide Important Safety Precautions Make sure to read this user s guide and follow the procedures below prior to screen operation.
More information