VARTECH. User s Guide. VT320 Large Screen Series 32.0 Large Screen Series LCD Monitors VT320D, VT320DX, VT320W. Solutions for Demanding Applications

Transcription

1 Solutions for Demanding Applications VARTECH S Y S T E M S I N C. Industrial CRT and Flat Panel Displays VT320 Large Screen Series 32.0 Large Screen Series LCD Monitors VT320D, VT320DX, VT320W User s Guide Read these instructions completely before attempting to operate your new Color Display. VT320 Liquid Display User Guide

2 Table Of Contents Page 1. GENERAL DESCRIPTION OVERVIEW 1.2 FEATURES 1.3 APPLICATIONS 2. ABSOLUTE RATINGS OF ENVIRONMENT 4 3. INTERFACE PIN CONNECTION DSub 15pin 3.2 DVID 24pin 3.3 SVideo 3.4 COMPONENT 3.5 COMPOSITE VIDEO 4. VARTECH ADJUSTMENTS OSD 4.2 OSD DISPLAY EXAMPLES 4.3 REMOTE CONTROL 4.4 ORIGINAL SETTING 5. EMC & SAFETY HANDLING PRECAUTIONS 19 VT320 Liquid Display User Guide

3 1. GENERAL DESCRIPTION 1.1 OVERVIEW VT320 is a 32 TFT Liquid Display with 16-CCFL Backlight units. This display supports 1366 x 768 WXGA format and can display true 16.7M colors (8-bit/ color). The inverter module for backlight is built-in. 1.2 FEATURES -High brightness (550 nits) -High contrast ratio (1000:1) -Fast response time (8msec) -High color saturation NTSC 75% -WXGA (1366 x 768 pixels) resolution -DE (Data Enable) only mode -Optimized response time for 50/60 Hz frame rate -Ultra wide viewing angle: 176(H)/176(V) (CR>20) Super MVA technology 1.3 APPLICATION -Direct view LCD flat panel display 4 VT320 Liquid Display User Guide

4 2. ABSOLUTE RATINGS OF ENVIRONMENT Note (1) Temperature and relative humidity range is shown in the figure below. (a) 90% RH Max. (Ta 40ºC) (b) Wet-bulb temperature should be 39ºC Max. (Ta > 40ºC) (c) No condensation. (2) The maximum operating temperature is based on the test condition that the surface temperature of display area is less than or equal to 60ºC with LCD module alone in a temperature controlled chamber. Thermal management should be considered in final product design to prevent the surface temperature of display area from being over 60ºC. The range of operating temperature may degrade in case of improper thermal management in final product design. (3) 11 ms, half sine wave, 1 time for ±X, ±Y, ±Z. (4) 10~200 Hz, 10 min, 1 time each X, Y, Z. (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough so that the module would not be twisted or bent by the fixture. VT320 Liquid Display User Guide

5 3. INTERFACE PIN CONNECTION VT320 Liquid Display User Guide

6 3 3 VARTECH SYSTEMS HEADQUARTERS Sun Belt Ct. Baton Rouge, Louisiana Toll-Free: International Phone: Fax: sales@vartechsystems.com VT320 Liquid Display User Guide

7 3 3 VT320 Liquid Display User Guide

8 3 VT320 Liquid Display User Guide

9 4. VARTECH ADJUSTMENTS 0, 100 0, , +45 0, 100 Off, Weak, Soft, Strong 0, 100 In, Out Left, Right Down, Up 0, 255 0, 255 Off, Single, PAP Small, Med, Large 0, 100 0, 100 1:1,Fill,Aspect,Panor Select 0, 255 0, 255 Off, 2.2, 2.4 0, 255 0, 255 0, 255 0, 255 0, 255 0, 15 0, 60 On, Off English Select Yes, No 0,255 Off, On 0, 100 VT320 Liquid Display User Guide

10 4 VT320 Liquid Display User Guide

11 4 VT320 Liquid Display User Guide

12 VT320 Liquid Display User Guide

13 VT320 Liquid Display User Guide

14 VT320 Liquid Display User Guide

15 VT320 Liquid Display User Guide

16 4 VT320 Liquid Display User Guide

17 4 VT320 Liquid Display User Guide

18 5. EMC & SAFETY This product was tested to the following standards and found compliance. Standards: FCC: CFR47, Part 15 / CISPR 22 Edition: 1997, Class B ANSI C63.4: 2003 Canadian ICES-003 CE: EN 55022: 1998+A1: 2000+A2: 2003, Class B EN 55024: 1998+A1: 2001+A2: 2003 IEC Series EN : 2000 & EN : 1995+A1: 2001 UL: UL : 2003, First Edition CSA C22.2 No Ed. April 1, 2003 TUV: IEC : 2001, First Edition VT320 Liquid Display User Guide

19 6. HANDLING PRECAUTIONS (1) The panel is made of glass, which may be broken or cracked if drop or bump on hard surface. Handle with extra care of the module. (2) Use a soft dry cloth without chemicals for cleaning, for the surface of polarizer is very soft and easily scratched. (3) It is recommended to assemble or install module into the user s system in clean working areas. The dust and oil may cause electrical short or worsen the polarizer. (4) Since contact with water may cause discoloration or spots, wipe off the water immediately when drop on the surface of the panel. (5) Always follow the correct power-on sequence when the LCD module is turned on. This can prevent the damage and latch-up of the CMOS LSI chips. (6) Take care of static electricity and handle with caution to prevent the damage of CMOS LSI in the module. (7) Do not pull the I/F connector in or out while the module is operating. (8) Moisture can easily penetrate into LCD module and may cause the damage during operation. (9) When handling LCD modules and assembling them into cabinets, please noted that longterm storage in the environment of oxidization or deoxidization gas and the use of such materials as reagent, solvent, adhesive, resin, etc. May cause corrosion and discoloration of the LCD module. (10) When ambient temperature is lower than 10, the display quality might be reduced. For example, the response time will become slow, and the starting voltage of CCFL will be higher than that of room temperature. VT320 Liquid Display User Guide

20 VARTECH SYSTEMS HEADQUARTERS Sun Belt Ct. Baton Rouge, Louisiana Toll-Free: International Phone: Fax: VT320 Liquid Display User Guide