High Resolution Multicolor Contrast Scanner. Dimensioned drawing
|
|
- Dora Preston
- 5 years ago
- Views:
Transcription
1 Specifications and description KRTM 20 High Resolution Multicolor Contrast Scanner Dimensioned drawing en / mm 20mm 50mm V DC 50 / 25 khz We reserve the right to make changes DS_KRTM20M_hr_Tdyn_en.fm Dynamic teach-in RGB transmitter Response time analog/digital (10μs/10μs or 10μs/20μs) Digital switching frequency 50kHz or 25kHz Resolution of 70 gray levels at the digital output Resolution of 400 gray levels at the analog output Analog output 1 10mA Changeover to the switching threshold Changeover to the analysis depth L/D switching Pulse stretching Accessories: (available separately) U L US C LISTED IEC IEC IP 67 M12 connectors, 5-pin (KD ) Ready-made cables (K-D ) Interchangeable objectives Tool for changing objectives A Light spot orientation vertical B Optical axis C M5/5.5mm deep D Scanning range E Front F Head Electrical connection PNP + analog PNP NPN + analog NPN
2 KRTM 20 Specifications Optical data Scanning range with objective 1 1) Scanning range with objective 2 2) Scanning range with objective 3 1) Light spot dimension with objective 1 1) Light spot dimension with objective 2 2) Light spot dimension with objective 3 1) Light spot orientation Light source Timing Switching frequency digital output Response time digital output Response jitter digital output Response time of analogue output Delay before start-up Electrical data Operating voltage U B Residual ripple Switching output Function characteristics Analog output Signal voltage high/low Output current Open-circuit current Indicators After power-on: ON LED on ON LED flashing slowly After teach-in: ON LED on 1) Interchangeable objective, available as accessory 2) Standard objective, state on delivery 3) 2=polarity reversal protection, 3=short-circuit protection for all outputs 12mm ± 1mm 20mm ± 2mm 50mm ± 5mm 3.0mmx1.0mm or round light spot D = 0.5mm 4.0mmx1.2mm or round light spot D = 0.6mm 10.0mmx2.0mm or round light spot D = 1.0mm vertical or horizontal LEDs (red, green, blue) 25kHz/50kHz reversible (see remarks) 20μs/10μs reversible (see remarks) 10μs 10μs 250ms 12 30VDC (incl. residual ripple) 15% of U B PNP, NPN light or dark switching, reversible via button 1 10mA (U B -2V)/ 2V max. 100mA 60mA device set to factory settings device not set to factory settings (display only for approx. 10s after power-on) switching threshold set to factory settings > switching threshold in center ON LED flashing slowly switching threshold was reconfigured > switching threshold close to the mark Q/T LED flashing quickly teaching error In run mode: ON LED on ready Delay LED pulse stretching on/off L/D LED light/dark switching Q/T LED on mark detected Q/T LED flashing quickly device error In configuration mode: ON LED flashing quickly device is in configuration mode Delay LED off 2x analysis depth (response time 20μs) Delay LED on 1x analysis depth (response time 10μs) L/D LED off switching threshold in center L/D LED on switching threshold close to the mark Mechanical data Housing diecast zinc Optics cover glass Weight 300g Connection type M12 connector, stainless steel, 5-pin Environmental data Ambient temp. (operation/storage) -25 C +60 C/-40 C +70 C Protection class IP 67 LED class 1 (acc. to EN ) VDE safety class II Protective circuit 3) 2, 3 Standards applied IEC Options Synchronous input PNP: Stop/Start measurement NPN: Stop/Start measurement Synchronization delay Teach input PNP: active / not active NPN: active/not active Teach delay Pulse stretching Device configuration Changeover switching threshold Changeover response time U B /0V or not connected 0V/U B or not connected 0.5ms U B /0V or not connected 0V/U B or not connected 10ms 20ms, can be activated via button continue to press the teach button during power-on see remarks see remarks Remarks Approved purpose: This product may only be used by qualified personnel and must only be used for the approved purpose. This sensor is not a safety sensor and is not to be used for the protection of persons. With shiny objects, the sensor is to be mounted at an angle to the object surface. Device configuration: 1. Configuration mode is activated by holding down the teach button during power-on (ON LED flashes). 2. The analysis depth is changed over using the Delay button: Delay LED off = 2x analysis depth (response time 20μs) Delay LED on = 1x analysis depth (response time 10μs) 3. The switching threshold is changed over using the L/D button: L/D LED off= Switching threshold in center L/D LED on= Switching threshold close to the mark 4. Press the teach button to end device configuration. 5. Back to factory settings: Simultaneously hold down the Delay button and the L/D button during poweron to reset the sensor to factory settings. Order guide See section Preferred types
3 KRTM 20 High Resolution Multicolor Contrast Scanner Function principle of the contrast scanner These contrast scanners are devices that can, with the aid of multiple transmitter colors (red, green, blue), distinguish between minimal gray levels (contrasts). By means of the automatic transmitter selection after a teach-in, the optimum functional safety for the respective contrast is determined and set by the device itself. As a result, any combination of marks or backgrounds can be detected with optimum functional safety. Through constant measurement and regulation of the emitted light, the devices operate with very good temperature stability. Re-teaching of the mark is, thus, no longer necessary. Each transmitter color consists of 4 LEDs. A longish light spot with four points is formed in the focal point. This very small, extremely bright light spot guarantees a high repeatability and positioning accuracy. For the case that the mark or background is not optimally printed, the light spot can be focused by slightly changing the scanning distance in such a way that a homogeneous, rectangular light spot is formed. With this teaching type, background and mark must be placed statically below the light spot. Using the synchronization input, the switching output can be activated or deactivated. Controls and indicators ON LED on ON LED flashing slowly ON LED flashing quickly ready / run mode device is not set to factory settings (Display only for approx. 10s after power-on) device is in configuration mode Q/T LED on Q/T LED flashing quickly mark detected teach error or device error Run mode: Delay LED Configuration mode: Delay LED off Delay LED on pulse stretching on /off 2x analysis depth (response time 20μs) 1x analysis depth (response time 10μs) Run mode: L/D LED Configuration mode: L/D LED off L/D LED on light/dark switching switching threshold in center switching threshold close to the mark Signal response during teach-in Dynamic 2-point teach Label with marks Open measurement window Close measurement window Receive signal Switching threshold in center Switching threshold near the mark Switching output for switching threshold in center Switching output for switching threshold near the mark Teach process The teach process is performed with the aid of the teach button or external teach lines. The two processes work in the same way. Operation Transmitter Indicator LED Position the light spot on the background Press the teach button approx. 0.5s or set the teach line to high level Advance paper sheet for at least one pattern length Briefly press teach button or teach line to low level Teaching error start new teaching process Red, green or blue light spot visible All colors are on White light spot visible All colors are on White light spot visible Changeover to red, green or blue Red, green or blue light spot visible All colors off Q/T, Delay and L/D LEDs flash Q/T, Delay and L/D LEDs flash ON LED on or flashes 3x Q/T LED on Q/T LED flashing > error ON LED on Q/T LED flashing > error
4 Calibration - analog output 1 10mA This is an uncalibrated measurement value. The current value that is output is proportional to the last contrast ascertained by means of teach-in. For rough calibration of the analog output, a teach-in with the following sequence is recommended. 1. Teach point on background > on white paper. 2. Teach point on mark > without object (into open space). KRTM 20 Preferred types Selection table Additional types on request Order code KRTM 20M/P S12 Part No Equipment Scanning range 12mm 20mm 50mm Light spot orientation vertical horizontal round Optical outlet front head Output wiring PNP NPN analogue current Other features static teach-in dynamic teach-in synchronous input
5 Specifications and description KRTM 20 High Resolution Multicolor Contrast Scanner Dimensioned drawing en / mm 20mm 50mm V DC 50 / 25 khz We reserve the right to make changes DS_KRTM20Mhighres_en_ _01.fm Static teach-in RGB transmitter Response time analog/digital (10μs/10μs or 10μs/20μs) Digital switching frequency 50kHz or 25kHz Resolution of 70 gray levels at the digital output Resolution of 400 gray levels at the analog output Analog output 1 10mA Changeover to the switching threshold Changeover to the analysis depth L/D switching Pulse stretching IEC IEC IP 67 Accessories: (available separately) M12 connectors, 5-pin (KD ) Ready-made cables (K-D ) Interchangeable objectives Tool for changing objectives A Light spot orientation vertical B Optical axis C M5/5.5mm deep D Scanning range E Front F Head Electrical connection PNP + analog PNP NPN + analog NPN
6 KRTM 20 Specifications Optical data Scanning range with objective 1 1) Scanning range with objective 2 2) Scanning range with objective 3 1) Light spot dimension with objective 1 1) Light spot dimension with objective 2 2) Light spot dimension with objective 3 1) Light spot orientation Light source Timing Switching frequency digital output Response time digital output Response jitter digital output Response time of analogue output Delay before start-up Electrical data Operating voltage U B 3) Residual ripple Switching output Function characteristics Analog output Signal voltage high/low Output current Open-circuit current Indicators After power-on: ON LED on ON LED flashing slowly After teach-in: ON LED on 12mm ± 1mm 20mm ± 2mm 50mm ± 5mm 3.0mmx1.0mm or round light spot D = 0.5mm 4.0mmx1.2mm or round light spot D = 0.6mm 10.0mmx2.0mm or round light spot D = 1.0mm vertical or horizontal LEDs (red, green, blue) 25kHz/50kHz reversible (see remarks) 20μs/10μs reversible (see remarks) 10μs 10μs 250ms 12 30VDC (incl. residual ripple) 15% of U B PNP, NPN light or dark switching, reversible via button 1 10mA (U B -2V)/ 2V max. 100mA 60mA device set to factory settings device not set to factory settings (display only for approx. 10s after power-on) switching threshold set to factory settings > switching threshold in center ON LED flashing slowly switching threshold was reconfigured > switching threshold close to the mark Q/T LED flashing quickly teaching error In run mode: ON LED on ready Delay LED pulse stretching on/off L/D LED light/dark switching Q/T LED on mark detected Q/T LED flashing quickly device error In configuration mode: ON LED flashing quickly device is in configuration mode Delay LED off 2x analysis depth (response time 20μs) Delay LED on 1x analysis depth (response time 10μs) L/D LED off switching threshold in center L/D LED on switching threshold close to the mark Mechanical data Housing diecast zinc Optics cover glass Weight 300g Connection type M12 connector, stainless steel, 5-pin Environmental data Ambient temp. (operation/storage) -25 C +60 C/-40 C +70 C Protection class IP 67 Light source free group (in accordance with EN 62471) VDE safety class II Protective circuit 4) 2, 3 Standards applied IEC Certifications UL 508, C22.2 No ) 5) Options Synchronous input PNP: Stop/Start measurement NPN: Stop/Start measurement Synchronization delay Teach input PNP: active / not active NPN: active/not active Teach delay Pulse stretching Device configuration Changeover switching threshold Changeover response time U B /0V or not connected 0V/U B or not connected 0.5ms U B /0V or not connected 0V/U B or not connected 10ms 20ms, can be activated via button continue to press the teach button during power-on see remarks see remarks 1) Interchangeable objective, available as accessory 2) Standard objective, state on delivery 3) For UL applications: for use in class 2 circuits according to NEC only 4) 2=polarity reversal protection, 3=short-circuit protection for all outputs 5) These proximity switches shall be used with UL Listed Cable assemblies rated 30V, 0.5A min, in the field installation, or equivalent (categories: CYJV/CYJV7 or PVVA/PVVA7) Remarks Approved purpose: This product may only be used by qualified personnel and must only be used for the approved purpose. This sensor is not a safety sensor and is not to be used for the protection of persons. With shiny objects, the sensor is to be mounted at an angle to the object surface. Device configuration: 1. Configuration mode is activated by holding down the teach button during power-on (ON LED flashes). 2. The analysis depth is changed over using the Delay button: Delay LED off = 2x analysis depth (response time 20μs) Delay LED on = 1x analysis depth (response time 10μs) 3. The switching threshold is changed over using the L/ D button: L/D LED off= Switching threshold in center L/D LED on= Switching threshold close to the mark 4. Press the teach button to end device configuration. 5. Back to factory settings: Simultaneously hold down the Delay button and the L/D button during poweron to reset the sensor to factory settings.
7 KRTM 20 High Resolution Multicolor Contrast Scanner Order guide The sensors listed here are preferred types; current information at Leuze webiste. Selection table Equipment Scanning range Order code KRTM 20M/P S12 Part No KRTM 20M/N S12 Part No KRTM 20M/C S12 Part No KRTM 20M/C S12 Part No KRTM 20M/P S12 Part No KRTM 20M/N S12 Part No mm 20mm 50mm Light spot orientation vertical horizontal round Optical outlet front head Output wiring PNP NPN analogue current Other features static teach-in dynamic teach-in synchronous input KRTM 20M/P S12 Part No Function principle of the contrast scanner These contrast scanners are devices that can, with the aid of multiple transmitter colors (red, green, blue), distinguish between minimal gray levels (contrasts). By means of the automatic transmitter selection after a teach-in, the optimum functional safety for the respective contrast is determined and set by the device itself. As a result, any combination of marks or backgrounds can be detected with optimum functional safety. Through constant measurement and regulation of the emitted light, the devices operate with very good temperature stability. Re-teaching of the mark is, thus, no longer necessary. Each transmitter color consists of 4 LEDs. A longish light spot with four points is formed in the focal point. This very small, extremely bright light spot guarantees a high repeatability and positioning accuracy. For the case that the mark or background is not optimally printed, the light spot can be focused by slightly changing the scanning distance in such a way that a homogeneous, rectangular light spot is formed. With this teaching type, background and mark must be placed statically below the light spot. Using the synchronization input, the switching output can be activated or deactivated.
8 KRTM 20 Controls and indicators ON LED on ON LED flashing slowly ON LED flashing quickly ready / run mode device is not set to factory settings (Display only for approx. 10s after power-on) device is in configuration mode Q/T LED on Q/T LED flashing quickly mark detected teach error or device error Run mode: Delay LED Configuration mode: Delay LED off Delay LED on pulse stretching on /off 2x analysis depth (response time 20μs) 1x analysis depth (response time 10μs) Run mode: L/D LED Configuration mode: L/D LED off L/D LED on light/dark switching switching threshold in center switching threshold close to the mark Signal response during teach-in Static 2-point teach Label with marks 1. Teach point on background 2. Teach point on mark Receive signal Switching threshold in center Switching threshold near the mark Switching output for switching threshold in center Switching output for switching threshold near the mark Teach process The teach process is performed with the aid of the teach button or external teach lines. The two processes work in the same way. Operation Transmitter Indicator LED Position the light spot on the background Press the teach button approx. 0.5s or set the teach line to high level Position the light spot on the mark Briefly press teach button or teach line to low level Teaching error start new teaching process Red, green or blue light spot visible All colors are on White light spot visible All colors are on White light spot visible Changeover to red, green or blue Red, green or blue light spot visible All colors off Q/T, Delay and L/D LEDs flash Q/T, Delay and L/D LEDs flash ON LED on or flashes 3x Q/T LED on Q/T LED flashing > error ON LED on Q/T LED flashing > error Calibration - analog output 1 10mA This is an uncalibrated measurement value. The current value that is output is proportional to the last contrast ascertained by means of teach-in. For rough calibration of the analog output, a teach-in with the following sequence is recommended. 1. Teach point on background > on white paper. 2. Teach point on mark > without object (into open space).
9 KRTM 20 Contrast scanner RGB Dimensioned drawing 12mm 20mm 50mm V DC 25 khz Freely programmable via protocol interface Freely adjustable transmitter colour, amplification and switching threshold Response time digital/analogue: 20µs/ 6.25µs Analogue and digital output Parameterisation input U L US C LISTED A Light spot orientation vertical B Optical axis C M5/5.5mm deep D Scanning range E Front F Head Electrical connection We reserve the right to make changes fmt_krt10gb.fm IEC IEC IP 67 Accessories: (available separately) M12 connectors, 5-pin (KD ) Ready-made cables (K-D ) Interchangeable objectives Tool for changing objectives
10 KRTM 20 Specifications Optical data Scanning range with objective 1 (accessory) 12mm ± 1mm Scanning range with objective 2 20mm ± 2mm Scanning range with objective 3 (accessory) 50mm ± 5mm Light spot dimensions with objective 1 3.0mmx1.0mm Light spot dimensions with objective 2 4.0mmx1.2mm Light spot dimensions with objective mmx2.0mm Light spot orientation vertical Light source LEDs (red, green, blue) Timing Digital switching frequency max. 25kHz Response time digital/analogue min. 20µs/6.25µs Delay before start-up 250ms Electrical data Operating voltage U B 12 30VDC (incl. residual ripple) Residual ripple 15% of U B Switching output PNP Function characteristics light switching Analogue output 1 10mA Signal voltage high/low (U B -2V)/ 2V Output current max. 100mA Bias current 60mA Indicators LED green 1 ON "ready" LED green 2 without function LED green 3 without function LED yellow Q/T "object detected" LED yellow flashing Q/T "device error, teach error" Keyboard Delay button locked (see remarks) L/D button locked (see remarks) Teach button locked Mechanical data Housing diecast zinc Optics cover glass Weight 300g Connection type M12 connector, stainless steel, 5-pin Environmental data Ambient temp. (operation/storage) -25 C +60 C/-40 C +70 C Protection class IP 67 LED class 1 (acc. to EN ) VDE safety class II Protective circuit 1) 2, 3 Standards applied IEC Options Input for parameterisation PNP: active / not active U B /0V or not connected 1) 2=polarity reversal protection, 3=short-circuit protection for all outputs Tables Diagrams Order guide See section 4. Preferred types Remarks With shiny objects, the sensor is to be mounted at an angle to the object surface. The objectives and objective covers must not be removed. Keyboard is disabled. Button LEDs must be "OFF". L/D and Delay buttons - KRTM S12: Dynamic keyboard locking (operable for approx. 10s after power-on). - KRTM S12: Static keyboard locking (not operable).
11 KRTM Function principle of the contrast scanner This contrast scanner is a device which, with the aid of multiple transmitter colours (red, green, blue), can differentiate between extremely small differences in contrast (grey tones). A protocol interface allows the transmitter colour, amplification and switching threshold to be freely programmed. Additionally, all internal values (including analogue value) can be read back via this protocol interface. As a result, the primary control can influence all sensor properties and also read back the actual measurement values in digital form. The switching threshold can also be freely adapted. Once parameterisation has been completed, the sensor functions as a standard contrast scanner and outputs the measurement values via the analogue output and switching output. Each transmitter colour consists of 4 LEDs. A longish light spot with four points is formed in the focal point. This very small, extremely bright light spot guarantees a high repeatability and positioning accuracy. For the case that the marker or background is not optimally printed, the light spot can be focused by slightly changing the scanning distance in such a way that a homogeneous, rectangular light spot is formed. 2. Controls and indicators LED ON (green) for "Ready" LED Q/T (yellow) for "Object detected" and "Error display" (flashing) LED Delay (green) without function (LED=OFF) LED L/D (green) without function (LED=OFF) 3. Signal response Data pulses: 3ms = 1, 6ms = 0 (High level) Pause = 3ms (Low level) Adjustable values: Switching threshold: (Bit0 Bit6) Transmitter colour: 1 3 (Bit0 Bit1), 1 = Red, 2 = Green, 3 = Blue Amplification level: 0 8 (Bit0 Bit7) Analogue value: (Bit0 Bit7) Parameterisation of switching threshold and transmitter colour: A Start B Switching threshold C Colour = blue D Pause E Request F Amplification level 7 Request for switching threshold:
12 KRTM 20 Acknowledgement of switching threshold and transmitter colour: Parameterisation of amplification level: A Start B Switching threshold C Colour = blue D Pause E Request F Amplification level = 7 G Analogue value = 129 Request for amplification level and analogue value: Acknowledgement of amplification level and analogue value: 4. Preferred types Selection table Equipment Scanning range Additional types on request Order code KRTM 20M/V S12 Part No KRTM 20M/V S12 Part No mm 20mm 50mm Transmitter colour RGB green Light spot orientation vertical horizontal round Optical outlet front head Output wiring PNP NPN analogue current Other features programmable via protocol interface static keyboard locking dynamic keyboard locking
13 Leuze electronic KRTM 20 Cut-Marking System Dimensioned drawing 20mm V DC 25 khz Static teach-in procedure Can store 128 data records Response time digital/analogue: 20µs/ 6.25µs 3 transmitters in the colours red, green, blue Programming via teach-in button We reserve the right to make changes fmt_krt08e.fm ISO 9001 Accessories: (available separately) U L US C LISTED IEC IEC IP 67 M12 connectors, 5-pin (KD ) Ready-made cables (K-D ) Interchangeable objectives Tool for changing objectives A Light spot orientation vertical B Optical axis C M5/5.5mm deep D Scanning range E Front F Head Electrical connection DSA Data set acknowledgement (Data Set Acknowledge) DSS Data set selection (Data Set Select)
14 Leuze electronic KRTM 20 Specifications Optical data Scanning range with objective 1 (accessory) 12mm ± 1mm Scanning range with objective 2 20mm ± 2mm Scanning range with objective 3 (accessory) 50mm ± 5mm Light spot dimensions with objective 1 3.0mmx1.0mm Light spot dimensions with objective 2 4.0mmx1.2mm Light spot dimensions with objective mmx2.0mm Light spot orientation vertical Light source LEDs (red, green, blue) Timing Digital switching frequency max. 25kHz Response time digital/analogue min. 20µs/6.25µs Delay before start-up 250ms Electrical data Operating voltage U B 12 30VDC (incl. residual ripple) Residual ripple 15% of U B Switching output PNP Function characteristics light or dark switching, reversible via button Analogue output 1 10mA Signal voltage high/low (U B -2V)/ 2V Output current max. 100mA Bias current 60mA Indicators LED green 1 ON "ready" LED green 2 "ON/OFF" delay LED green 3 L/D "light/dark switching" LED yellow Q/T "object detected" LED yellow flashing Q/T "device error, teach error" Keyboard Release via bit 9 of the data protocol Mechanical data Housing diecast zinc Optics cover glass Weight 300g Connection type M12 connector, stainless steel, 5-pin Environmental data Ambient temp. (operation/storage) -25 C +60 C/-40 C +70 C Protection class IP 67 LED class 1 (acc. to EN ) VDE safety class II Protective circuit 1) 2, 3 Standards applied IEC Options Input for data-record selection PNP: active / not active U B /0V or not connected Pulse stretching 20ms, can be activated via button 1) 2=polarity reversal protection, 3=short-circuit protection for all outputs Tables Diagrams Order guide See section 5. Preferred types Remarks With shiny objects, the sensor is to be mounted at an angle to the object surface. The objectives and objective covers must not be removed.
15 Leuze electronic KRTM Method of function of the cut-marking system With this contrast scanning system, 128 data records can be stored in the sensor in zero-voltage-safe memory. A simple and asynchronous protocol is used for data-record selection and assignment. The transmission rate is specified by the controller by means of the start-bit pulse width. As a result, the contrast scanning system can work together with any controller system. A standardised serial interface, e.g. RS 232, is not required as communication is realised via standard PNP signals. Adjustment is performed by means of static teach-in via the keyboard, i.e. background and mark must be statically positioned below the light spot. Contrast detection is achieved with the aid of multiple transmitter colours (red, green, blue). This allows the detection of minimal differences in contrast (grey tones). Each transmitter colour consists of 4 LEDs. A longish light spot with four points is formed in the focal point. This very small, extremely bright light spot guarantees a high repeatability and positioning accuracy. For the case that the marker or background is not optimally printed, the light spot can be focused by slightly changing the scanning distance in such a way that a homogeneous, rectangular light spot is formed. 2. Controls and indicators LED ON (green) for "Ready" LED Q/T (yellow) for "Object detected" and "Error display" (flashing) LED Delay (green) for pulse stretching 20ms (LED=ON) LED L/D (green) for dark switching (LED=ON) 3. Protocol procedure for selecting a data record - 1. The sensor system determines the period length T (T = n*10ms) from the start bit. The start bit must be a multiple of 10ms. Maximum period duration T max =200ms A pause lasting 3T follows the start bit Transmission of bit 9... bit 0 (evaluation of the level in the middle of the period) - 4. Acknowledgement of the data record following reception of bit 0. The sensor system repeats the entire protocol (start bit + 3T + bit 9... bit 0) at the switching output During data-record selection, mark detection is not active. Data-record selection by the controller via pin 5 and acknowledgement of the data record by the sensor system via pin 4 (switching output Q): Bit 9 - button lock (1=all buttons disabled, 0=all buttons enabled) Bit 8 - no function Bit 7 - no function Bit 6 - most significant bit of the data-record number (1=high level, 0=low level) Bit 0 - least significant bit of the data-record number (1=high level, 0=low level) Start bit
16 4. Teach process The teach process is performed with the aid of the Teach button. The keyboard is enabled via bit 9. Leuze electronic Operation Transmitter Indicator LED Position the light spot on the background Press the Teach button approx. 1s Position the light spot on the marker Press the Teach button approx. 1s Teaching error start new teaching process Red, green or blue light spot visible All colours are on White light spot visible All colours are on White light spot visible Changeover to red, green or blue Red, green or blue light spot visible All colours off All LEDs flash All LEDs flash KRTM 20 ON (green) illuminated Q/T (yellow) off Q/T (yellow) flashing (error) ON (green) illuminated Q/T (yellow) flashing (error) SSignal response during teach-in Label Teach button Switching threshold Received signal LED Q/T Switching output with light switching Switching output with dark switching 5. Preferred types Selection table Equipment Scanning range Order code KRTM 20M/V S12 Part No mm 20mm 50mm Transmitter colour RGB green Light spot orientation vertical horizontal round Optical outlet front head Output wiring PNP NPN analogue current Other features cut-marking system can store 128 data records static teach-in teach-in, background synchronous input
17 KRTM 20M/N S12 Cut-marking system Dimensioned drawing en / mm V DC 80 khz Dynamic teach-in process Can store 128 data records Programming via teach-in via button or teach input (pin 5) Remote control after teach-in Small, round light spot (1 of 4 LEDs) We reserve the right to make changes DS_KRTM20MN200084S12_en_ fm IEC IEC IP 67 Accessories: (available separately) M12 connectors, 5-pin (KD ) Ready-made cables (K-D ) Interchangeable objectives Tool for changing objectives A Light spot orientation vertical B Optical axis C M5/5.5mm deep D Scanning range E Front F Head Electrical connection DSA Data set acknowledgment (Data Set Acknowledge) DSS Data set selection (Data Set Select)
18 KRTM 20M/N S12 Specifications Optical data Scanning range with objective 1 (accessory) 11mm (in focus mode) Scanning range with objective 2 18mm (in focus mode) Scanning range with objective 3 (accessory) 44mm (in focus mode) Light spot dimensions with objective 1 Ø 0.5mm Light spot dimensions with objective 2 Ø 0.6mm Light spot dimensions with objective 3 Ø 1.0mm Light source LEDs (red, green, blue) Timing Clock frequency 160kHz Switching frequency 80kHz Analysis depth 1 Response time 6.75μs Jitter 6.75μs Delay before start-up 250ms Electrical data Operating voltage U B 12 30VDC (incl. residual ripple) Residual ripple 15% of U B Switching output NPN Function 1. Operational function light or dark switching, reversible via button 2. Remote control 2Hz pulse sequence (after faulty teach-in via pin 5 or button) Analog output 1 10mA Signal voltage high/low (U B -2V)/ 2V Output current max. 100mA Open-circuit current 100mA Indicators LED green 1 ON "ready" LED green 2 "ON/OFF" delay LED green 3 L/D "light/dark switching" Yellow LED Q/T "object detected" Yellow LED, flashing Q/T "device error, teach error" Keyboard Release via bit 9 of the data protocol Mechanical data Housing diecast zinc Optics cover glass Weight 300g Connection type M12 connector, stainless steel, 5-pin Environmental data Ambient temp. (operation/storage) -25 C +60 C/-40 C +70 C Protection class IP 67 Light source exempt group (in acc. with EN 62471) VDE safety class II Protective circuit 1) 2, 3 Standards applied IEC Options Input for data-record selection NPN: active/not active 0V/U B or not connected Teach-in input NPN: active/not active 0V/U B or not connected (for function see item 4) Synchr. input NPN: active/not active 0V/U B or not connected (for function see item 4) Pulse stretching 10ms, can be activated via button Remote control 2Hz on switching output pin 4 (after teaching error) acknowledgement of the teaching error, see pt.4. Teach event Compensation active temperature and LED compensation through reference receiver 1) 2=polarity reversal protection, 3=short-circuit protection for all outputs Order guide See section 5. Preferred types Tables Diagrams Remarks Approved purpose: This product may only be used by qualified personnel and must only be used for the approved purpose. This sensor is not a safety sensor and is not to be used for the protection of persons. With shiny objects, the sensor is to be mounted at an angle to the object surface. The objectives and objective covers must not be removed. This data sheet applies for device firmware with production date after 1210xxxxxxx (year=2012, month=october).
19 KRTM 20M/N S12 1. Method of function of the cut-marking system With this contrast scanning system, 128 data records can be stored in the sensor in zero-voltage-safe memory. A simple and asynchronous protocol is used for data-record selection and assignment. The transmission rate is specified by the controller by means of the start-bit pulse width. As a result, the contrast scanning system can work together with any controller system. A standardized serial interface, e.g. RS 232, is not required as communication is realized via standard NPN signals. Setting is performed with dynamic teach-in via the keyboard or teach input (pin 5). When teach-in starts, a measurement window opens and closes when teach-in ends. The minimum and maximum values are determined and the switching threshold is set in the center. Contrast detection is achieved with the aid of multiple transmitter colors (red, green, blue). This allows the detection of minimal differences in contrast (gray tones). Each transmitter color consists of 1 LED. A round light spot is formed in the focal point. This very small, extremely bright light spot guarantees a high repeatability and positioning accuracy. The system features a reference receiver which ensures temperature and LED compensation. This leads to a very stable longterm behavior. The contrast scanners are not calibrated against reference contrasts. 2. Controls and indicators LED ON (green) for "Ready" LED Q/T (yellow) for "Object detected" and "Error display" (flashing) LED delay (green) for pulse stretching 10ms (LED=ON) LED L/D (green) for dark switching (LED=ON) In the factory settings, the keyboard is enabled. 3. Protocol procedure for selecting a data record - 1. The sensor system determines the period length T (T = n*5ms) from the start bit. The start bit must be a multiple of 5ms. Maximum period duration T max =100ms A pause lasting 3T follows the start bit Transmission of bit 9... bit 0 (evaluation of the level in the middle of the period) Acknowledgment of the data record following reception of bit 0. The sensor system repeats the entire protocol (start bit + 3T + bit 9... bit 0) at the switching output During data-record selection, mark detection is not active. Data-record selection by the controller via pin 5 and acknowledgment of the data record by the sensor system via pin 4 (switching output Q): Bit 9 - button lock (0V = all buttons disabled, U B = all buttons enabled 1) ) Bit 8 - no function Bit 7 - no function Bit 6 - most significant bit of the data-record number (0V = active, U B = inactive) Bit 0 - least significant bit of the data-record number (0V = active, U B = inactive) Start bit 1) Factory setting
20 4. Teach process The teach event is performed with the aid of the teach button or the teach input (pin 5). Teach-in via teach button The keyboard is enabled via bit 9. Operation Transmitter Indicator LED Position the light spot on the background Press the teach button approx. 0.5s Move the light spot onto or over the mark Press the teach button approx. 0.5s Teaching error start new teaching process Teach-in via teach input (pin 5) Pulse> 200ms starts the dynamic teach-in. Red, green or blue light spot visible All colors are on White light spot visible All colors are on White light spot visible Changeover to red, green or blue Red, green or blue light spot visible All colors off KRTM 20M/N S12 All LEDs flash All LEDs flash ON (green) illuminated Q/T (yellow) off Q/T (yellow) flashing (error) ON (green) illuminated Q/T (yellow) flashing (error) Pulse > 200ms opens the teach window Rising edge closes the teach window Acknowledgment of a teaching error after teach-in (pin 5) One pulse <2ms acknowledges the teaching error and activates the last valid teach values. 5. Preferred types Selection table Equipment Pulse < 2ms Order code KRTM 20M/N S12 Part no Scanning range (in focus mode) 11mm 18mm 44mm Transmitter color RGB green Light spot orientation vertical horizontal round Optical outlet Front Head Output wiring PNP NPN analogue current Other features cut-marking system can store 128 data records dynamic teach-in teach-in, background synchronous input
Electrical connection
Colour sensors Dimensioned drawing Part No. 50109619 12.5mm 60mm 10-30 V DC 6 khz Scanner for colour detection Very short response time 85µs for detection of fast or small objects and marks Direct indication
More informationElectrical connection
Colour sensors Dimensioned drawing en 02-2014/05 50109619-01 12.5mm 60mm 10-30 V DC 6 khz Scanner for colour detection Very short response time 85µs for detection of fast or small objects and marks Direct
More informationElectrical connection
Splice sensor Dimensioned drawing en 04-2014/06 50116166-01 4mm 12-30 V DC We reserve the right to make changes DS_IGSU14CSD_en_50116166_01.fm Reliable detection of splice on paper web or plastic web With
More informationElectrical connection
Color sensors Dimensioned drawing en 02-2013/01 50121262 068-14515 12mm 32mm 10-30 V DC 500 Hz Scanner for color detection Simultaneous selection of up to 3 colors Detection independent of distance Teach-in
More informationADVANCED ultrasonic sensors with analog output. Dimensioned drawing
ADVANCED ultrasonic sensors with analog output Dimensioned drawing en 07-2017/02 50124880 4...20 ma 0...10 V 25 400mm 150 1300mm 15-30 V DC We reserve the right to make changes PAL_DMU418BX3LTVC_en_50124880.fm
More informationElectrical connection
(I)GSU 14C Ultrasonic Label Fork Dimensioned drawing en 06-2011/12 50109234-01 4mm 12-30 V DC 4 m/s We reserve the right to make changes DS_IGSU_14C_en.fm Ultrasonic forked sensor for universal application
More informationAmplifier for fiber optics. Dimensioned drawing
Amplifier for fiber optics Dimensioned drawing up to 525mm up to 120mm 10-30 V DC 3-digit display for indicating and setting the switching threshold NEW: AutoSet function for easy sensor adjustment Menu
More information1.5mm amplitude at 10 to 55Hz frequency in each X, Y, Z direction for 2 hours 500m/s² (approx. 50G) in each X, Y, Z direction for 3 times
Color Mark Color Mark Feature Outstanding color matching accuracy - RGB light emitting diodes and 12-bit resolution - 2 detection modes (color only / color + intensity) - -step sensitivity adjustment for
More informationCSM Color sensors. Color sensors for the detection of a single color in restricted space conditions
CSM Color sensors Color sensors for the detection of a single color in restricted space conditions Due to its compact design, the CSM can be used in the most confined of spaces. The choice of color tolerance
More informationAmplifier for fiber optics. Dimensioned drawing
Amplifier for fiber optics Dimensioned drawing with cable en 01-2012/09 50118006 up to 1050mm up to 270mm with M8 connector 10-30 V DC We reserve the right to make changes DS_LV463_en_50118006.fm wo, large,
More informationWF next: Fork sensors for a wide range of applications
WF next: Fork sensors for a wide range of applications D ATA S H E E T Fork sensors TThe detection of labels, marks and double sheets, as well as holes and edges are typical applications for the new WF
More informationDimensions. Model Number. Electrical connection. Features. Pinout Product information. Indicators/operating means. LGS25 Serie.
Q Dimensions Transmitter Detection field + 9. Detection field 7.8 n Beam. Beam Receiver III 0. 0 Fix H H H Fn Model Number Light grid with fixed cable with -pin, M x connector, and fixed cable with 8-pin,
More informationRLS Series RLS-GD-20/20 -UV. Design. RLS-GD Series Gloss Detection Sensors. Accessories: (cf. page 9) Product name:
RLS Series RLS-GD-20/20 -UV Detection of Glass Coating - Insensitive to outside light due to clocked UV illumination - Receiver (20 ) and reference - Storing of up to 31 gloss degrees (gloss values) -
More informationTechnical data. General specifications. Indicators/operating means
Model Number Single head system Features Sensor head bidirectional and rotatable Function indicators visible from all directions Quick mounting bracket Selectable sound lobe width Programmable Diagrams
More informationSPECTRO Series. SPECTRO-1-30-UV/VIS-9x1. Design. SPECTRO-1 Series Single-Channel Sensors (Contrast Measurement) Product name:
SPECTRO Series SPECTRO-1-30-UV/VIS-9x1 - Measuring range typ. 10 mm... 40 mm - 9x UV LED, 375 nm, focused (AC-/DC-operation or OFF for luminous objects can be switched) - Additional slit aperture 9 mm
More informationTransmitter optics with 9x white light LED (optics cover made of glass)
SPECTRO Series SPECTRO-3-85-FCL-30 /30 - Recommended measuring distance: typ. 50 mm ± 5 mm - Big dynamic range due to focused white-light operation - Up to 31 colors can be stored - RS232 interface (USB
More informationTechnical data. General specifications. 60 ma Power consumption P 0. 1 W Time delay before availability t v. 120 ms Interface. Protocol IO-Link V1.
Model Number Single head system Features IO-link interface for service and process data Programmable via DTM with PACTWARE programmable switch outputs Selectable sound lobe width Synchronization options
More informationSPECTRO Series SPECTRO-1-30-UV/UV. Design. SPECTRO-1 Series Single-Channel Sensors (Contrast Measurement) Product name:
SPECTRO Series SPECTRO-1-30-UV/UV - Measuring range typ. 10 mm... 40 mm - 9x UV LED, 375 nm, focused (AC-/DC-operation or OFF for luminous objects can be switched) - High scan frequency (max. 200 khz in
More informationSPECTRO Series SPECTRO-3-30-UV. Design. SPECTRO-3 Series True Color Sensors. Product name: Accessories: (p. 9-10)
SPECTRO Series SPECTRO-3-30-UV - Measuring range typ. 15 mm... 80 mm - Ideal adjustment to luminescent objects - Up to 31 colors can be stored - RS232 interface (USB or Ethernet adapter is available) -
More informationSPECTRO Series SPECTRO-1-50-DIL. Design. SPECTRO-1 Series Single-Channel Sensors (Contrast Measurement) Product name:
SPECTRO Series - Measuring range typ. 20 mm... 80 mm - Reduction of gloss effect due to diffuse illumination - 9x super-bright white-light LED, diffuse (AC-/DC-operation or OFF for luminous objects can
More informationOperating Instructions
CNTX Contrast sensor Operating Instructions CAUTIONS AND WARNINGS SET-UP DISTANCE ADJUSTMENT: As a general rule, the sensor should be fixed at a 15 to 20 angle from directly perpendicular to the target
More informationtechnical data (according to IEC ) Degree of protection IP 67 Max. ripple content 15 % U B / 20 % U B (amplifier) No-load supply current
Inductive Sensors: high-temperature ü For ambient temperatures of up to +230 C ü With integrated electronics, up to +180 C ü With external electronics, up to +230 C ü Excellent long-term reliability (according
More informationSPECTRO Series SPECTRO-3-50-UV-JR. Aufbau. SPECTRO-3 Series True Color Sensors. Product name: SPECTRO-3-50-UV-JR (incl. software SPECTRO3-Scope)
SPECTRO Series - Measuring range typ. 15 mm... 100 mm - Up to 31 colors can be stored - RS232 interface (USB adapter is available) - 8x UV LED, 382 nm, focused (AC-/DC-/PULSEoperation or OFF for luminous
More informationSPECTRO Series SPECTRO-3-30-UV-ANA. Design. SPECTRO-3 Series True Color Sensors. Product name:
SPECTRO Series SPECTRO-3-30-UV-ANA - Measuring range typ. 15 mm... 80 mm - Transmitter power of UV LED can be adjusted for excitation of luminescent marks - Up to 3 colors (or color groups) can be stored
More informationSPECTRO Series SPECTRO-3-20-COF. Design. SPECTRO-3 Series True Color Sensors. Product name: Accessories: (p. 9)
SPECTRO Series SPECTRO-3-20-COF - Measuring range typ. 15 mm... 30 mm - Integrated transmitter and receiver optics (confocal) - Up to 31 colors can be stored - RS232 interface (USB or Ethernet adapter
More informationSPECTRO Series SPECTRO-3-50-COF-...-CL. Design. SPECTRO-3 Series True Color Sensors. Product name:
SPECTRO Series SPECTRO-3-50-COF-...-CL - Measuring range typ. 30 mm... 70 mm - Integrated transmitter and receiver optics (confocal) - Up to 31 colors can be stored - RS232 interface (USB or Ethernet adapter
More informationSERIES x5. Nickel-plated brass Connection 1) PUR cable type 1 Degree of protection. IP 67 Mounting. Embeddable Max. switching frequency
1 Size SERIES 400 x SERIES x Operating distance mm 0.8 0.8 1. Housing material Connection 1) PUR cable type 1 PUR cable type 1 / Connector S8 PUR cable type 1 Degree of protection Mounting Max. switching
More informationSU17 Series Fiber Optic Sensors
SU17 Series Fiber Optic Sensors Fiber Optic Diffuse and Thru-Beam Mode See page 750 Sensing Range: Determined by fiber optic cable Output: NPN, PNP Built-in auto-tuning Digital display Mutual interference
More informationSENSORS S62. Compact Sensors - S62. The most complete universal sensor in a compact 50x50 mm housing. Sensors with red, infrared LED or LASER emission
Compact Sensors - S6 S6 The most complete universal sensor in a compact x housing Sensors with red, infrared or LASER emission from 3 cm to m Polarized retroreflective up to 0 m Multivoltage 4-40Vac/4-60Vdc
More informationOnline data sheet SGS4-S108P3PS2W03 SLG SWITCHING AUTOMATION LIGHT GRIDS
Online data sheet SGS-S08PPSW0 SLG SWITCHING AUTOATI LIGHT GRIDS SGS-S08PPSW0 SLG SWITCHING AUTOATI LIGHT GRIDS A B C D E F H I J K L N O P R S T Detailed technical data Features Technology Ordering information
More informationLUT Luminescence scanners: Seeing what no-one else can
LUT Luminescence scanners Luminescence scanners LUT Luminescence scanners: Seeing what no-one else can Special features: A semi-conductor light source is used in the LUT series no lamp change required.
More informationDS 400 P. Intelligent Electronic Pressure Switch in Hygienic Stainless Steel Ball Housing. on hygienic process connections
Intelligent Electronic Pressure Switch in Hygienic Stainless Steel Ball Housing Description The electronic pressure switch is the successful combination of hygienic process connections with flush welded
More informationW 190 L: Application-based Laser Technology, the optimum solution for demanding applications
Photoelectric proximity switches Photoelectric reflex switches W 90 L: Application-based Laser Technology, the optimum solution for demanding applications Do your customers require reliable sensors suitable
More informationSPECTRO Series SPECTRO-3-50-FCL-JR. Design. SPECTRO-3 Series True Color Sensors. Product name: SPECTRO-3-50-FCL-JR (incl. software SPECTRO3-Scope)
SPECTRO Series - Measuring range typ. 10 mm... 150 mm - Big dynamic range due to focused white-light operation - Up to 31 colors can be stored - RS232 interface (USB or Ethernet adapter available) - 8x
More informationAPPLICATIONS. Automatic warehouse. Trasportation lines
INDUCTIVE TUBULAR SENSOR M8 SERIES There are millions of inductive sensors deployed in almost every area of factory automation. They detect metal objects contactless and are distinguished by a long operating
More informationFiber-Optic Sensor Amplifiers E3S-X3, E3X-NL and E3X-NM Discontinued March 2012; Revised Replacements
NO: PH-165 PRODUCT: E3S-X3, E3X-NL, E3X-NM DATE: August 2012 TYPE: Discontinuation Update Fiber-Optic Sensor Amplifiers E3S-X3, E3X-NL and E3X-NM Discontinued March 2012; Revised Replacements Affected
More informationAPPLICATIONS. Automatic warehouse. Trasportation lines
INDUCTIVE TUBULAR SENSOR M12 SERIES There are millions of inductive sensors deployed in almost every area of factory automation. They detect metal objects contactless and are distinguished by a long operating
More informationPhotoelectric Sensors with Separate Digital Amplifiers (Laser-type Amplifier Units)
Photoelectric Sensors with Separate Digital Amplifiers (Laser-type Amplifier Units) All seven laser types provide ample long distance, for the Diffuse Reflective Model 1.000 mm and for Retroreflective
More informationAbsolute Encoders Multiturn
The Sendix 5863 and 5883 multiturn encoders with SSI or BiSS-C interface and optical sensor technology can achieve a resolution of max. 29 bits. A through hollow shaft up to 4 mm and a blind hollow shaft
More informationPROXIMITY SWITCHES INDUCTIVE TUBULAR SENSOR M30 SERIES HIGHLIGHTS APPLICATIONS
INDUCTIVE TUBULAR SENSOR M30 SERIES There are millions of inductive sensors deployed in almost every area of factory automation. They detect metal objects contactless and are distinguished by a long operating
More informationV 180 Series Photoelectric Switches
D A T A S H E E T V 180 Series Photoelectric Switches VS 180 / VE 180 1 m x VL 180 m 1 m*) *) with polarizing filter v VT 180 110 mm 00 mm n Photoelectric switches of cylindrical design in threaded metal
More informationLWC Series LWC-80. Design. LWC Series Laser Wire Counters. Product name: Accessories: LWC-80
LWC Series LWC-80 Laser Wire Counting - Insensitive to outside light (due to interference filter, modulated light) - Visible laser spot (red light 670 nm) - Parameterisable through integrated switch and
More informationCapacitive sensor BCT5-S18-UP6X2T-H1151
M18 1 threaded barrel Plastic, PA12-GF30 Teach-in and configuration via buttons on the device, pin 5 and IO-Link Wiring Diagram Functional principle Type designation Ident no. 2101100 Remark to product
More informationPhotoelectric sensor Laser Distance Sensor (Triangulation) Q4XFKLAF310-Q8
Transmission of process value and parametrization via IO-link 4-digit 7-segment LED display 3 buttons Output indicator (yellow) IP67/69K ECOLAB-certified Range: 35 310 mm Laser class 1, red, 655 nm, acc.
More informationInstruction Manual. Universal Flow Controller Model 261 / 261-EC-01
Universal Flow Controller Model 261 / 261-EC-01 Instruction Manual Type ARS 261-EC 01 Art.-no: 82212264 Table of Contents 1. Safety Instructions 2. Product ID - Dimensions 3. Function Description 4. Installation
More informationSensor technologies Proximity sensors Series ST4. Brochure
Series ST Brochure 2 Series ST ST Sensor, Series ST with cable open cable ends, -pin Sensor, Series ST mm C-slot with cable Plug, M8, -pin 6 Sensor, Series ST mm C-slot with cable Plug, M8, -pin, with
More informationSafety Light Curtains GuardShield
Description The Allen-Bradley Guardmaster safety light curtain is an economical, fully featured, Type 4 safety light curtain in a uniquely styled housing. safety light curtains are general purpose presence
More informationSlot-type Photomicrosensor with connector or pre-wired models (Non-modulated) *1. configuration. Dark-ON/Light-ON
Slot-type Photomicrosensor with connector or pre-wired models (Non-modulated) * EE-SX/6 Photomicrosensor with 0- to 00-mA direct switching capacity for built-in application. Series includes models that
More informationPhotoelectric Sensors E3F2
Photoelectric Sensors E3F2 Threaded Cylindrical Photoelectric Sensors with Built-in Amplifier for Use as an Optical Proximity Switch M18 DIN-sized cylindrical housing Housing materials: plastic, nickel
More informationRK-2 ENVIRONMENTAL DATA CONTACTLESS MAGNETOSTRICTIVE LINEAR POSITION TRANSDUCER WITH FLANGED HEAD. Main characteristics
RK-2 CONTACTLESS MAGNETOSTRICTIVE LINEAR POSITION TRANSDUCER WITH FLANGED HEAD (ANALOG OR START/STOP OUTPUT) Main characteristics Absolute transducer Strokes from 50 to 4000mm (RK-2- -N/E/S) Digital output
More informationPhotoelectric sensor Laser Distance Sensor (Triangulation) Q4XTKLAF300-Q8
Transmission of process value and parametrization via IO-link 4-digit 7-segment LED display 3 buttons Output indicator (yellow) IP67/69K ECOLAB-certified Range: 25 300 mm Laser class 1, red, 655 nm, acc.
More information45 mm : all channels. Output indicator Yellow LED System status indicator Light source Infrared (880 nm) Opening angle +/ 4 Emission angle +/ 5
SPACEGUARD SERIES Description 1-12 metre sensing range 16 to 56 parallel scanning beams Active height of 0 mm to 2520 mm Detector length of 1928 mm to 2648 mm 3 different channel placement models Cable
More informationPhotoelectrics Through-beam Type PA18C.T..., DC
Photoelectrics Through-beam Type, DC Miniature sensor range Range: 20 m (Axial), 16 m (Radial) Sensitivity adjustment by potentiometer Modulated, infrared light 850 nm Supply voltage: to 30 VDC Output:
More informationPhotoelectric sensor Laser Distance Sensor (Triangulation) Q4XTKLAF100-Q8
Transmission of process value and parametrization via IO-link 4-digit 7-segment LED display 3 buttons Output indicator (yellow) IP67/69K ECOLAB-certified Range: 25 100 mm Laser class 1, red, 655 nm, acc.
More informationL-LAS Series L-LAS-LT-50-SL-... Design. L-LAS Series Laser Line Sensors. Product name:
L-LAS Series L-LAS-LT-50-SL-... - Line laser
More informationUltrasonic Sensor Diffuse Mode Sensor RU40U-M18E-LIU2PN8X2T-H1151
Smooth sonic transducer face Cylindrical housing M18, potted Connection via M12 x 1 male Teach range adjustable via pushbutton or adapter Temperature compensation Blind zone: 2.5 cm Range: 40 cm Resolution:
More informationOperating instructions Electronic preset counter Type series 717
Operating instructions Electronic preset counter Type series 717 1. Description 5.98.3_gb 6-digit adding/subtracting counter with two presets Very bright 8mm high LED display Counting and preset range
More informationOperating instructions Through-beam sensor. OJ51xx laser / / 2010
Operating instructions Through-beam sensor OJ5xx laser 70480 / 00 05 / 200 Contents Preliminary note. Symbols used 2 Safety instructions Functions and features 4 4 Installation 4 5 Electrical connection5
More informationPhotoelectric sensor Laser Distance Sensor (Triangulation) Q4XFKLAF610-Q8
Transmission of process value and parametrization via IO-link 4-digit 7-segment LED display 3 buttons Output indicator (yellow) IP67/69K ECOLAB-certified Range: 35 610 mm Laser class 1, red, 655 nm, acc.
More informationUltrasonic Sensor Diffuse Mode Sensor RU600U-EM30E-LIU2PN8X2T-H1151/3GD
ATEX II 3 G approval Gases and vapors IIC group, zone 2 Dusts IIIC group, zone 22 When used in Ex areas, the special conditions of the approval must be observed Safety clips to prevent inadvertent detachment
More informationLD OEM/LD PDS/LD PeCo
LD OEM/LD PDS/LD PeCo Features LD OEM/PDS: 360 field of view LD OEM: the basic platform to LD PeCo: 90 field of view provide customized software 14,400 Hz scan rate programs on board and offers the Class
More informationSafety Light Curtain C 4000
O P E R A T I N G I N S T R U C T I O N S Safety Light Curtain C 4000 Operating Instructions Chapter 2 On safety 2 On safety This chapter deals with your own safety and the safety of the equipment operators.!
More informationLinear encoders without bearings incremental System for linear motion feedback
Features Robust magnetic sensing method Output signals A 90 B with index signal Output circuits: HTL/push-pull and TTL/RS422 Resolution up to 5 µm (4-times evaluation) Non-contact, wear-free sensing system
More informationL-LAS Series L-LAS-LT-2500-XL. Design. L-LAS Series Laser Line Sensors. Product name: L-LAS-LT-2500-XL
L-LAS Series - Line laser
More informationSPECTRO Series SPECTRO-3-5-DIF-ANA. Design. SPECTRO-3 Series True Color Sensors. Product name:
SPECTRO Series - Measuring range typ. 3 mm... 30 mm - Reduction of gloss effect due to diffuse illumination (optimal diffusing effect due to a volume scattering lens as diffusor) - Up to 3 colors (max.
More informationSPECTRO Series SPECTRO-3-50-FCL. Aufbau. SPECTRO-3 Series True Color Sensors. Product name: Accessories: (p. 10)
SPECTRO Series - Measuring range typ. 10 mm... 150 mm - Big dynamic range due to focused white-light operation - Up to 31 colors can be stored - RS232 interface (USB or Ethernet adapter is available) -
More informationTroubleshooting. 1. Symptom: Status indicator (Red LED) on SSR is constant on. 2. Symptom: Output indicator (Yellow LED) on SSR is flashing.
Product Data Electrical Data SST (Transmitter) SSR (Receiver) Supply voltage 18 30 V dc Max. Voltage ripple 15 % (within supply range) Current consumption 100 ma (RMS) 75 ma Digital - 100 ma Max. outputs
More informationPhotoelectric sensor Photoelectric Sensor for Plastic Fibers DF-G1-KS-Q7
8 mm connector, 4-pin Visible red light Programming via teach cable or multi-function button Operating voltage: 10 30 VDC IO-Link 2 x PNP output, changeover contact Light/dark operation Wiring Diagram
More informationW100L: Laser Sensor in Mini- Format
Product group W00 Laser Photoelectric proximity switch energ. Photoelectric reflex switch W00L: Laser Sensor in ini- Format Through-beam photoelectric switch Where applications demand it, the sensor can
More informationBMOA Component Systems. Miniature Optical Sensors. c Features. Technical Description
Component Systems Technical Description Features Applications The mini optical series of sensors are among smallest sensors in the world. Mini optical sensors require almost no space and with their low
More informationDS 200 P DS 200 P. Electronic Pressure Switch with Flush Process Connection
with Flush Process Connection piezoresistive pressure sensor up to independent contacts, configurable optional: analogue output Exprotection (for wire) cooling element up to 00 C nominal pressure ranges
More informationW 9-2: A Versatile, Complete and Compact Series
suitable sensor can be selected from the W 9- series. Overview of the sensors: WT 9-, with adjustable background suppression, max. scanning distance 0 mm, WT 9-, energetic, max. scanning distance 0 mm,
More informationData Sheet SPECTRO-3-SLU-BA-ANA + SI-SLU-16. Receiver optics incl. 3-color filter detector (True Color), scratch-resistant optics cover made of glass
SPECTRO Series SPECTRO-3-SLU-BA-ANA + SI-SLU-16 - Measuring range in reflected light operation typ. 100 mm... 1000 mm, in transmitted light operation typ. 100 mm... 5000 mm - Up to 3 colors (max. 64 in
More information1 Inductive proximity switches. 5 Connecting cables. Highlights: New:
Highlights: - All-metal housings - Miniature sizes - Long operating distances - Extreme environmental conditions - Analog outputs New: - All-metal devices for food industry and sea-water applications -
More informationAssembly. Front view. LEDs. Parametrization interface. Power Bus
otation Speed Monitor Features Assembly 1-channel signal conditioner 2 V DC supply Input for 2- or -wire sensors Input frequency 10 mhz... 50 khz elay contact output Start-up override and restart inhibit
More informationAnalog Input Module HART Ex n Inputs, 8 Channels Series 9461/15
> 8 channels for 2-wire HART transmitters > Inputs for Ex nl, Ex na and Nonincendive > Galvanic separation between inputs and system > Open-circuit and short-circuit monitoring for each field circuit >
More informationLt DELTA USA, Inc
Infrared LOOP SCANNER Rota-Sonde TS2006 Infrared - high sensitivity 480 F or 750 F Quick and easy commissioning Self-monitoring and alarm functions Lt 1037 1 Applications R o t a - S o n d e TS2 0 0 6
More informationLight Curtain Type LA
Light Curtain Type LA Status: 2011-04-27 Subject to change without notice. No responsibility is taken for the correctness of this information. Your suggestions for corrections or improvements are welcome!
More informationSPACESCAN SERIES SS 02
Description 0-10 metre sensing range 12 to 384 channels Available with channel spacing of 5, 10 or 20 mm Active length of 225 mm to 1920 mm Housing length of 300 mm to 1980 mm Plug connection 18-30 V dc
More informationSPECTRO Series SPECTRO-1-POF. Design. SPECTRO-1 Series Single-Channel Sensors (Contrast Measurement) Accessories: (p ) Product name:
SPECTRO Series SPECTRO-1-POF - Big assortment of plastic optic fibers of POF Series available (diffuse reflection or through-beam sensor types) - Working range for diffuse reflection types: typ. 1 mm...
More informationDS 210. Electronic Pressure Switch. Without Media Isolation. accuracy according to IEC 60770: 0.35 % FSO. Nominal pressure
Without Media Isolation accuracy according to IEC 60770: 0. % FSO Nominal pressure from 0... 0 mbar up to 0... 000 mbar Contacts, or independent contacts freely configurable Analogue output wire:... 0
More informationSelection matrix for electronic pressure switches
Selection matrix for electronic pressure switches Type / series 0500 050 050 05 050 0570 050 05 05 05 050 05 05 05 055 056 Page 09 09 7 0 5 5 5 5 9 9 9 9 9 9 Technology Measuring cell ceramic / thick-film
More informationKNX Dimmer RGBW - User Manual
KNX Dimmer RGBW - User Manual Item No.: LC-013-004 1. Product Description With the KNX Dimmer RGBW it is possible to control of RGBW, WW-CW LED or 4 independent channels with integrated KNX BCU. Simple
More informationSPECTRO Series SPECTRO /0 -MSM-ANA-VIS. Design. SPECTRO-3 Series True Color Sensors. Accessories: (p. 8-9) Product name:
SPECTRO Series SPECTRO-3-28-45 /0 -MSM-ANA-VIS - Object distance (measuring range) 28 mm ± 2 mm - Color control to 45 /0 method (45 transmitter arrangement, 0 receiver arrangement) - L*a*b*, L*C*h*, L*u*v*,
More informationContactless Encoder SSI RI360P0-QR24M0-HESG25X3-H1181
Compact, rugged housing Many mounting possibilities Status displayed via LED Positioning element and aluminium ring not incl. output 25 bit, Gray-coded clock rate: 62.5 KHz 1 MHz Single or multiturn, length
More informationPOSIWIRE. WS61 with internal magnetic encoder Position Sensor. Cable Extension Position Sensors. Datasheet
Cable Extension Position Sensors with internal magnetic encoder Position Sensor Datasheet Copyright ASM GmbH Am Bleichbach 18-24 85452 Moosinning Germany The information presented in this data sheet does
More informationE6CP-A. An Absolute Encoder at About the Same Price as an Incremental Encoder. Ideal for robot limit signals. Low-cost Encoder with Diameter of 50 mm
Low-cost Encoder with Diameter of 50 mm CSM DS_E An Absolute Encoder at About the Same Price as an Incremental Encoder. Ideal for robot limit signals. High-precision detection of automatic machine timing.
More informationIS 140 IGA 140 IS 140-PB IGA 140-PB IS 140-PN IGA 140-PN IS 140-ET IGA 140-ET
IMPAC Infrared Temperature Sensors focusable optics for non-contact temperature measurements on metals, ceramics, graphite etc. between 220 and 3500 C IS 140 IGA 140 IS 140-PB IGA 140-PB IS 140-PN IGA
More informationTrue Color Sensor with Analog and Digital Outputs
SMARTEYE ColorWise TM 2 Specialty Application Photoelectric Sensors True Color Sensor with Analog and Digital Outputs 2-79 Specialty Application Photoelectric Sensors 2 SMARTEYE ColorWise TM The SMARTEYE
More informationModel KBF P 240 Humidity test chambers with ICH-compliant light source
Model KBF P 240 Humidity test chambers with ICH-compliant light source The KBF P humidity test chamber, equipped with ICH-compliant light source, is an expert when it comes to photostability tests and
More informationFeatures of the 745T-20C: Applications of the 745T-20C: Model 745T-20C 20 Channel Digital Delay Generator
20 Channel Digital Delay Generator Features of the 745T-20C: 20 Independent delay channels - 100 ps resolution - 25 ps rms jitter - 10 second range Output pulse up to 6 V/50 Ω Independent trigger for every
More informationIMPAC Infrared Thermometers
IMPAC Infrared Thermometers focusable optics for non-contact temperature measurements on metals, ceramics, graphite etc. between 300 and 3300 C IS 140 IGA 140 IS 140-PB IGA 140-PB Short response times
More informationPhotoelectric sensor Retroreflective Sensor with Polarizing Filter for Clear Object Detection QS18EK6XLPCQ
Transmission of process value and parametrization via IO-link Cable with male end, PVC, M8 x 1, 4-pin, 150 mm Protection class IP67 LED, all-round visible Coaxial optics Sensitivity adjusted via teach
More informationDRS61: Incremental encoders, number of lines and zero pulse width freely programmable DRS60: Incremental Encoders with Zero-Pulse-Teach
NEW DRS: Incremental encoders, number of lines and zero pulse width freely programmable DRS: s with Zero-Pulse-Teach Further highlights of this generation of encoders: Simple zero-pulse-teach by pressing
More informationOperating instructions Retro-reflective sensor. OJ50xx laser / / 2010
Operating instructions Retro-reflective sensor OJ50xx laser 70481 / 00 05 / 010 Contents 1 Preliminary note3 1.1 Symbols used 3 Safety instructions 3 4 Installation 4 4.1 Installation of the supplied mounting
More informationModel KBF 115 Constant climate chambers with large temperature / humidity range
Model KBF 115 Constant climate chambers with large temperature / humidity range The BINDER KBF is the specialist for unconditionally reliable stability testing and precise maintenance of constant climate
More informationModel KBF 1020 Constant climate chambers with large temperature / humidity range
Model KBF 1020 Constant climate chambers with large temperature / humidity range The BINDER KBF is the specialist for unconditionally reliable stability testing and precise maintenance of constant climate
More informationContactless encoder Ri360P0-QR24M0-HESG25X3-H1181
Compact, rugged housing Many mounting possibilities Status displayed via LED Positioning element and aluminium ring not incl. SSI output 25 bit, Gray-coded SSI clock rate: 62.5 KHz 1 MHz Single or multiturn,
More informationMultifunction devices
devices devices devices, electronic Type Page LED multifunction displays pulse, frequency, time (DC) Codix 524 240 pulse, frequency, time (AC+DC) Codix 544 243 LCD multifunction preset counters 1 or 2
More informationModel KT 53 Cooling incubators with thermoelectric cooling
Model KT 53 Cooling incubators with thermoelectric cooling The KT series combines outstanding performance with impressive energy efficiency and environmental friendliness. The cooled incubators of the
More information