ADDENDUM TO REZAC AUDITORIUM LIGHTING RFP P1617-M-5

Transcription

1 ADDENDUM TO REZAC AUDITORIUM LIGHTING RFP P1617-M-5 UNDER BASE BID PART 1. GENERAL 1.0 WORK INCLUDED ADD THE FOLLOWING: o The Theatrical Contractor shall provide the materials and services of an electrical contractor for a turn-key installation under this contract. o The Theatrical Contractor must visit the site to ensure all items specified and provided in his bid will comply and work with the site conditions. o The Electrical Contractor, as part of this contract section, shall act as a sub contractor to the Theatrical Contractor. o The Electrical Contractor shall disconnect the old dimmer rack, demo existing low voltage control wire and stations, install new dimmer rack, pull new low voltage control wire (provided by the Theatrical Contractor) and test a complete lighting control system as specified herein, attached installation matrix and the circuit schedules. Existing equipment shall remain with the owner for final disposal. Provide and install all other incidental items necessary for the complete and proper operation. o The Electrical Contractor must visit the site to ensure all items specified and provided in his bid will comply and work with the site conditions. o The Electrical Contractor shall furnish all conduit, wire, connectors, hardware and other incidental items necessary for the complete and proper electrical operation of the lighting control system. o The Electrical Contractor shall coordinate all work described in this section with all other applicable specifications. UNDER BASE BID PART 1. GENERAL 2.16 DIMMER MODULES DELETE THE FOLLOWING: o G. Provide the following: Power Control System to consist of: A. DR A SR Black Sensor3 48-Module Dimmer Rack - Designed for 3 phase 4 wire and ground operation at a maximum of 800A, 120/208V, 60Hz AC A SR3-48 DOOR - Black SR3-48 Locking Door with Filter A1003 CEM3 - CEM3 Control Module 1 Custom Item Custom label for dimmer rack A1031 D20E - Dual 20A Dimmer Module, 500µs rise time (96 Dimmers)

2 Control System to consist of: o Existing Control Console o Equipment Rack 1 QUOTE RACK - Black 19" rack sized as job requires and to include: quad power box, and blank panels to fill 1 QUOTE DOOR - Door for Rack A1013 ERN2-RM ERn2 Enclosure Rack-mount V A1005 ERN-RPS - ERn Redundant Power Supply Module - Cannot be used with ERn- NET A1009 P-ACP2 - Paradigm Architectural Control Processor A1001 P-SPM - Paradigm Station Power Module - supports 32 stations and (1) 500m wire segment A2008 PATCH PANEL 24X - 2U 19" rack-mount patch panel with 24 open slots 23 N2027 Cat5e Modular Jack for above Patch Panel 1 PJJ1002 UTP Pass through for patch panel 1 SGE1062 MAP BR2-2U Brush Grommet Panel 24 N4035 2' CAT5 Patch cable, black 1 SGN1129-M CISCO SG300-28PP - Cisco Switch - 24 RJ-45 ports of 10/100/1000 PoE+ (180W total allowance) - 2 RJ-45 ports of 10/100/ combo ports of RJ-45 or mini-gbic/sfp 1 PJPS1012 MAP 1000R VA / 750W rack-mount UPS o Multi Box Type 1 (Booth) 1 ECPB N/N/N - ETCNet / ETCNet / ETCNet Station with: 2 - RJ-45 (568B) Connectors in XLR cases A1039 ECPB PB3 - ETC 3-gang Surface Mount Back Box (3.5" deep) o Multi Box Type (SMP Catwalk) 2 QUOTE ECPB DMX Out / NET / NET - DMX Out / Net / Net Control Plug-in Station with: 1 - XLR-5FDM3 DMX Out Connector(s) 2 - RJ-45 (568B) Connector in XLR case A1040 ECPB PB4 - ETC 4-gang Surface Mount Back Box (3.5" deep) A1050 -U - U-Bolt Pipe-mounting Assembly (1 pair) o Multi Box Type N-GIB (1st, 2nd, 3rd electrics) 3 Custom Item Net Grid Iron Junction Box with 75 Proplex Net cable secured to existing SO cable to extend from grid iron to SR pipe batten end. (Plug into Portable gateway(s) listed below) o Multi Box Type 4 (Booth) 1 QUOTE ECPB DMX In / DMX IN / DMX IN - DMX Input / DMX Input / DMX Input Control Plug-in Station with: 3 - XLR-5MDM3 DMX In Connector(s) Labeled as DMX-In 1 Dimmer, DMX-In 2 Catwalk, DMX-In 3 SMP A1039 ECPB PB3 - ETC 3-gang Surface Mount Back Box (3.5" deep)

3 o Portable Gateways A1103 N3T2G-2F - Portable (Touring) Net3 Only Two Port Output Gateway to Contain: 2 - XLR-D5F, 5-pin Female XLR connectors with hanger bracket for c-clamp or U-bolt Configure both connectors as Outputs, DMX universe 1 Install in Catwalk, 1 st, 2 nd, 3 rd Electrics with all necessary cables as required A CC - Black C-Clamp A SC - Safety Cable Black Architectural Control System to consist of: o Portable (Booth) A1532 P-TS7-PE - Paradigm 7" Ethernet Portable Touchscreen Station to include: - 7" Black Portable Touchscreen - 10' Ethercon to RJ-45 cable 1 SGM76 25' Network Cable (Cat 5, Neutrik Ethercon to RJ45) o Entry Station (Replace as existing) 4 QUOTE UH10002-_Z - Standard Color (Color TBD) 1-gang faceplate assembly to include the following: 2 - Select Switch Standard nomenclature as On, Off, LED back light shall be illuminated Green when preset is in the Off state B2004 UH gang, 1-button electronics assembly w/ir Port A SBB1 - Unison 1-gang surface-mounted back box o LCD (SMP) A P-TS7-4 - Paradigm 7" Touchscreen Station to include: - 7" Black Touchscreen Assembly - Mounting Collar - LinkConnect/ Ethernet termination kit A1503 P-LCD-SBB - Paradigm surface mount touchscreen back box Accessories 1 Portable Uninterruptable Power Supply capable of powering existing control console and monitors for up to 1-hour. - Install in booth for existing control console 1 Low Voltage control cable as necessary for all DMX, Paradigm and Network System(s) - Provide and terminate as necessary -Installation by the Electrical Contractor Option A1022 NET3-RFR - Net3 Radio Focus Remote Universal Frequency to Include: 1 - Base Station with: 1 - USB Port to connect to Console 1 - Ethercon Ethernet Port to connect to Lighting Network

4 1 - Hand Held Transmitter with: 1-24 button Backlit keypad 2 - Encoder wheels 1 - Mini USB port for Recharging Battery 1 - ON/Off Switch 1 - USB A to B Cable 1 - USB A to Mini B Cable Wall-Wart Power Supply Belt Clip End BOM UNDER BASE BID PART 1. GENERAL INSERT THE FOLLOWING AFTER SECTION 2.16, F ColorSource PAR Wash fixture A. General 1. The fixture shall be a color-mixing high-intensity LED illuminator with DMX control of intensity and color. The fixture shall be a ColorSource Par as manufactured by Electronic Theatre Controls, Inc. or approved equal. 2. All LED fixtures shall be provided by a single manufacturer to ensure compatibility 3. The fixture shall be UL 1573 listed for stage and studio use 4. The fixture shall comply with the USITT DMX-512 A standard B. Physical 1. The fixture shall be contained in a rugged all-metal die-cast housing, free of burrs and pits 2. The housing shall have a rugged black powdercoat finish a. White or silver/gray powdercoat finishes shall be available as color options b. Other powdercoat color options shall be available on request 3. Power supply, cooling and electronics shall be integral to each unit. 4. Fixture housing shall provide two easy-access slots for secondary lenses and other accessories a. Slots shall be equipped with locking retaining clip 5. The unit shall ship with a. Theatrical-style hanging yoke as standard b. 5' power lead with Edison connector as standard 6. Available options shall include but not be limited to: a. Floor stand conversion Kit b. Bare-end, Stage-Pin or Twist-lock type-equipped power leads c. PowerCon to PowerCon cables for fixture power linking d. Multiple secondary lens options to include multiple angles in the following patterns: 1. Linear 2. Round

5 3. Oblong 7. Light output shall be via a round aperture a. Aperture and accessory slots shall accommodate standard 7.5" accessories such as used in other similar-sized fixtures b. Accessories available as options shall include but not be limited to: 1. Gel/diffusion frames 2. Top hats 3. Barndoors 4. Egg crate louvers 5. Concentric ring louvers 6. Multiple secondary lensing options C. ENVIRONMENTAL AND AGENCY COMPLIANCE 1. The fixture shall be UL and cul LISTED and/or CE rated, and shall be so labeled when delivered to the job site. 2. The fixture shall be UL LISTED to the UL1573 standard for stage and studio use 3. The fixture shall be rated for IP-20 dry location use. D. THERMAL 1. The fixture shall be cooled with a variable speed fan. 2. The fixture shall utilize advanced thermal management systems to maintain LED life to an average of 70% intensity after 20,000 hours of use a. Thermal management shall include multiple temperature sensors within the housing to include: 1. The LED array 2. The control board 3. The fixture shall operate in an ambient temperature range of 0 C (32 F) minimum, to 40 C (104 F) maximum ambient temperature. E. ELECTRICAL 1. The fixture shall be equipped with 100V to 240V 50/60 Hz internal power supply 2. The fixture shall support power in and thru operation a. Power in shall be via Neutrik PowerCon input connector b. Power thru shall be via Neutrik PowerCon output connector c. Fixture power wiring and accessory power cables shall be rated to support linking of multiple fixtures up to the capacity of a 15A breaker 3. The fixture requires power from non-dim source 4. Power supply outputs shall have self-resetting current limiting protection 5. Power supply shall have power factor correction F. LED Emitters 1. The fixture shall contain 4 different LED colors to provide color characteristics as described in Section H below 2. All LEDs used in the fixture shall be high brightness and proven quality from established and reputable LED manufacturers. a. Fixture shall utilize Luxeon Z LED emitters 3. Manufacturer of LED emitters shall utilize an advanced production LED binning process to maintain color consistency. 4. LED emitters should be rated for nominal 20,000 hour LED life to 70% intensity 5. All LED fixtures (100% of each lot) shall undergo a minimum three-hour burn-in test during manufacturing. 6. LED system shall comply with all relevant patents

6 G. CALIBRATION 1. Fixture shall be calibrated at factory for achieve consistent color between fixtures built at different times and/or from different LED lots or bins a. Calibration data shall be stored in the fixture as a permanent part of on-board operating system b. All arrays, including replacement arrays shall be calibrated to the same standard to insure consistency c. Fixtures not offering LED calibration shall not be acceptable H. COLOR 1. The fixture shall utilize an minimum of 40 LED emitters a. These emitters shall be made up of Red, Green, Blue and Lime I. DIMMING 1. The LED system shall use 15-bit nonlinear scaling techniques for highresolution dimming. 2. The dimming curve shall be optimized for smooth dimming over longer timed fades. 3. The LED system shall be digitally driven using high-speed pulse width modulation (PWM) 4. LED control shall be compatible with broadcast equipment in the following ways: a. PWM control of LED levels shall be imperceptible to video cameras and related equipment b. PWM rates shall be adjustable by the user via RDM to avoid any visible interference to video cameras and related equipment J. CONTROL AND USER INTERFACE 1. The fixture shall be USITT DMX 512A-compatible via In and Thru 5-pin XLR connectors 2. The fixture shall be compatible with the ANSI RDM E1.20 standard a. All fixture functions shall accessible via RDM protocol for modification from suitably equipped control console b. Temperature sensors within the luminaire shall be viewable in real time via RDM c. Fixtures not offering RDM compatibility, feature set access or temperature monitoring via RDM shall not be compatible 3. The fixture shall be equipped with a 7-segment display for easy-to-read status and control 4. The fixture shall be equipped with a three-button user-interface 5. The fixture shall offer RGB control 6. The fixture shall operate in Regulated mode for droop compensation 7. The fixture shall offer stand-alone functionality eliminating the need for a console a. Fixture shall ship with 12 preset colors accessible as a stand-alone feature b. Fixture shall ship with 5 Sequences accessible as a stand-alone feature c. Each color and sequence can be modified by the end user d. Fixtures can be linked together with standard DMX cables and controlled from designated master fixture 1. Up to 32 fixtures may be linked e. Fixtures in a stand-alone state shall restore to the settings present prior to power cycling, eliminating the need for reprogramming

7 f. Fixtures without stand-alone operation features described in a, b, c, d, and e shall not be acceptable 2.18 ColorSource Spot Profile fixture A. General 1. The fixture shall be a color-mixing high-intensity LED illuminator with DMX control of intensity and color. The fixture shall be a ColorSource Spot as manufactured by Electronic Theatre Controls, Inc. or approved equal. 2. All LED fixtures shall be provided by a single manufacturer to ensure compatibility 3. The fixture shall be UL 1573 listed for stage and studio use 4. The fixture shall comply with the USITT DMX-512A standard B. Physical 1. The unit shall be constructed of rugged, die cast aluminum, free of burrs and pits 2. The following shall be provided: a. Lens secured with silicone shock mounts b. Shutter assembly shall allow for +/-25 rotation c. 20 gauge stainless steel shutters d. Interchangeable lens tubes for different field angles with Teflon guides for smooth tube movement e. Sturdy integral die cast gel frame holders with two accessory slots, and a top-mounted, quick release gel frame retainer f. Rugged steel yoke with two mounting positions allowing rotation of the fixture within the yoke g. Positive locking, hand operated yoke clutch h. Slot with sliding cover for motorized pattern devices or optional iris 3. The housing shall have a rugged black powder coat finish a. White or silver/gray powder coat finishes shall be available as color options b. Other powder coat color options shall be available on request 4. Power supply, cooling and electronics shall be integral to each unit. 5. The unit shall ship with a. Theatrical-style hanging yoke as standard b. 5' cable with Neutrik PowerCon to choice of connector as standard c. Gate diffuser d. A-size pattern holder 6. Available options shall include but not be limited to: a. Bare-end, Stage-Pin or Twist-lock type-equipped power leads b. PowerCon to PowerCon cables for fixture power linking c. Smooth Wash Diffuser for overlapping beams of light from multiple fixtures C. Optical 1. The light beam should have a 2-to-1 center-to-edge drop-off ratio 2. The unit shall provide, but not be limited to: a. Low gate and beam temperature b. Sharp imaging through a three-plane shutter design

8 3. The unit shall provide, but not be limited to: a. 5, 10, 14, 19, 26, 36, 50, 70 and 90 degree field angles b. High-quality pattern imaging c. Sharp shutter cuts without halation d. Shutter warping and burnout in normal use shall be unacceptable e. Adjustable hard and soft beam edges 4. 19, 26, 36, and 50 degree units shall have optional lens tubes available for precision, high-contrast imaging. D. Environmental and Agency Compliance 1. The fixture shall be ETL and cetl LISTED and/or CE rated, and shall be so labeled when delivered to the job site. 2. The fixture shall be ETL LISTED to the UL1573 standard for stage and studio use 3. The fixture shall be rated for IP-20 dry location use. E. Thermal 1. Fixture shall be equipped with a cooling fan. 2. The fixture shall utilize advanced thermal management systems to maintain LED life to an average of 70% intensity after 20,000 hours of use a. Thermal management shall include multiple temperature sensors within the housing to include: 1. LED array circuit board temperatures 2. Fixture ambient internal temperature 3. The fixture shall operate in an ambient temperature range of 0 C (32 F) minimum, to 40 C (104 F) maximum ambient temperature. F. Electrical 1. The fixture shall be equipped with a 100V to 240V 50/60Hz internal power supply 2. The fixture shall support power in and thru operation a. Power in shall be via Neutrik PowerCon input connector b. Power thru shall be via Neutrik PowerCon output connector c. Fixture power wiring and accessory power cables shall be rated to support linking of multiple fixtures up to the capacity of a 15A breaker 3. The fixture requires power from a non-dim source 4. Fixtures shall have droop compensation to prevent thermal shift of color or intensity 5. Power supply outputs shall have self-resetting current-limiting protection 6. Power supply shall have power factor correction G. LED Emitters 1. The fixture shall contain a minimum of four different LED colors to provide color characteristics as described in the Color Section below 2. All LEDs used in the fixture shall be high brightness and proven quality from established and reputable LED manufacturers. a. Fixture shall utilize Luxeon Rebel LED emitters 3. Manufacturer of LED emitters shall utilize an advanced production LED binning process to maintain color consistency. 4. LED emitters should be rated for nominal 20,000-hour LED life to 70% intensity 5. All LED fixtures (100% of each lot) shall undergo a minimum three-hour burn-in test during manufacturing. 6. LED system shall comply with all relevant patents

9 H. Calibration 1. Fixture shall be calibrated at factory for achieve consistent color and intensity output between fixtures built at different times and/or from different LED lots or bins a. Calibration data shall be stored on the control card as a permanent part of on-board operating system b. All arrays, including replacement arrays shall be calibrated to the same standard to insure consistency c. Fixtures not offering LED calibration shall not be acceptable I. Color 1. The fixture shall utilize a minimum of 60 LED emitters 2. The fixture shall utilize a selective mix of Red, Green, Blue and Lime emitters J. Dimming 1. The LED system shall use 15-bit nonlinear scaling techniques for highresolution dimming. 2. The fixture shall utilize a Incandescent dimming curve 3. Dimming curve shall be optimized for smooth dimming over longer timed fades. 4. The LED system shall be digitally driven using high-speed pulse width modulation (PWM) 5. LED control shall be compatible with broadcast equipment in the following ways: a. PWM control of LED levels shall be imperceptible to video cameras and related equipment b. PWM shall be capable of being set via RDM to 25,000hz K. Control and User interface 1. The fixture shall be USITT DMX 512A-compatible via In and Thru 5-pin XLR connectors or RJ45 connectors 2. The fixture shall be compatible with the ANSI RDM E1.20 standard a. All fixture functions shall accessible via RDM protocol for modification from suitably equipped control console b. Temperature sensors within the luminaire shall be viewable in real time via RDM c. Fixtures not offering RDM compatibility, feature set access or temperature monitoring via RDM shall not be compatible 3. The fixture shall be equipped with a 7-segment display 4. The fixture shall be equipped with a three-button user-interface 5. The fixture shall be controlled via RGB data input a. 5-channel footprint (IRGBS) 6. A variable-rate strobe channel shall be provided 7. The fixture shall offer stand-alone functionality eliminating the need for a console a. Fixture shall ship with 12 preset colors accessible as a stand-alone feature b. Fixture shall ship with 5 sequences accessible as a stand-alone feature c. Each color and sequence can be modified by the end user via RDM d. Fixtures can be linked together with standard DMX cables and controlled from designated master fixture 1. Up to 32 fixtures may be linked

10 e. Fixtures in a stand-alone state shall restore to the settings present prior to power cycling, eliminating the need for reprogramming f. Fixtures without stand-alone operation features described above shall not be acceptable 2.19 Source Four LED Series 2 Profile fixture A. General 1. The fixture shall be a color-mixing high-intensity LED illuminator with DMX control of intensity and color. The fixture shall be a Source Four LED Series 2 as manufactured by Electronic Theatre Controls, Inc. or approved equal. 2. All LED fixtures shall be provided by a single manufacturer to ensure compatibility 3. The fixture shall be UL 1573 listed for stage and studio use 4. The fixture shall comply with the USITT DMX-512A standard B. Physical 1. The unit shall be constructed of rugged, die cast aluminum, free of burrs and pits, finished in black. 2. The following shall be provided: a. Lens secured with silicone shock mounts b. Shutter assembly shall allow for +/-25 rotation c. 20 gauge stainless steel shutters d. Interchangeable lens tubes for different field angles with Teflon guides for smooth tube movement e. Sturdy integral die cast gel frame holders with two accessory slots, and a top-mounted, quick release gel frame retainer f. Rugged steel yoke with two mounting positions allowing rotation of the fixture within the yoke g. Positive locking, hand operated yoke clutch h. Slot with sliding cover for motorized pattern devices or optional iris 3. The housing shall have a rugged black powder coat finish a. White or silver/gray powder coat finishes shall be available as color options b. Other powder coat color options shall be available on request 4. Power supply, cooling and electronics shall be integral to each unit. 5. The unit shall ship with a. Theatrical-style hanging yoke as standard

11 b. 5' Neutrik PowerCon to Edison power cable as standard c. Gate diffuser d. A-size pattern holder 6. Available options shall include but not be limited to: a. Bare-end, Stage-Pin or Twist-lock type-equipped power leads b. PowerCon to PowerCon cables for fixture power linking c. Smooth Wash Diffuser for overlapping beams of light from multiple fixtures C. Optical 1. The light beam should have a 2-to-1 center-to-edge drop-off ratio 2. The unit shall provide, but not be limited to: a. Low gate and beam temperature b. Sharp imaging through a three-plane shutter design 3. The unit shall provide, but not be limited to: a. 5, 10, 14, 19, 26, 36, 50, 70 and 90 degree field angles b. High-quality pattern imaging c. Sharp shutter cuts without halation d. Shutter warping and burnout in normal use shall be unacceptable e. Adjustable hard and soft beam edges 4. 19, 26, 36, and 50 degree units shall have optional lens tubes available for precision, high-contrast imaging. D. Environmental and Agency Compliance 1. The fixture shall be ETL and cetl LISTED and/or CE rated, and shall be so labeled when delivered to the job site. 2. The fixture shall be ETL LISTED to the UL1573 standard for stage and studio use 3. The fixture shall be rated for IP-20 dry location use. E. Thermal 1. Fixture shall be equipped with a cooling fan. a. Fan speed control via a DMX channel shall be possible b. Fan speed software shall permit the fixture to override DMX fan speed setting to prevent heat damage to the fixture 2. The fixture shall utilize advanced thermal management systems to maintain LED life to an average of 70% intensity after 20,000 hours of use a. Thermal management shall include multiple temperature sensors within the housing to include: 1. LED array circuit board temperatures 2. Temperature sensors placed on each individual LED color circuit 3. Fixture ambient 4. CPU b. Fixture user shall permit monitoring of temperature sensors via a legible LCD multi-line backlit display c. Fixtures that do not provide active thermal monitoring of LED circuits and other temperature readings shall not be acceptable

12 3. The fixture shall operate in an ambient temperature range of 0 C (32 F) minimum, to 40 C (104 F) maximum ambient temperature. F. Electrical 1. The fixture shall be equipped with a 100V to 240V 50/60Hz internal power supply 2. The fixture shall support power in and thru operation a. Power in shall be via Neutrik PowerCon input connector b. Power thru shall be via Neutrik PowerCon output connector c. Fixture power wiring and accessory power cables shall be rated to support linking of multiple fixtures up to the capacity of a 15A breaker 3. The fixture requires power from a non-dim source 4. Power supply outputs shall have self-resetting current-limiting protection 5. Power supply shall have power factor correction G. LED Emitters 1. The fixture shall contain a minimum of four different LED colors to provide color characteristics as described in the Color Section below 2. All LEDs used in the fixture shall be high brightness and proven quality from established and reputable LED manufacturers. a. Fixture shall utilize Luxeon Rebel and/or Osram OSLON Square LED emitters 3. Manufacturer of LED emitters shall utilize an advanced production LED binning process to maintain color consistency. 4. LED emitters should be rated for nominal 20,000-hour LED life to 70% intensity 5. All LED fixtures (100% of each lot) shall undergo a minimum three-hour burn-in test during manufacturing. 6. LED system shall comply with all relevant patents 7. Fixtures shall have adjustable PWM frequency up to 25,000hz to avoid flicker on camera H. Calibration 1. Fixture shall be calibrated at factory for achieve consistent color and intensity output between fixtures built at different times and/or from different LED lots or bins a. Calibration data shall be stored on the LED array as a permanent part of on-board operating system b. All arrays, including replacement arrays shall be calibrated to the same standard to insure consistency c. Fixtures not offering LED calibration shall not be acceptable I. Color 1. The fixture shall utilize a minimum of 60 LED emitters 2. The fixture shall be available in specialized LED arrays as outlined below: a. Source Four LED Series 2 Lustr 1. Red, Amber, Green, Cyan, Blue, Indigo and Lime LEDs in an array designed for broad spectrum color, light tints, and variable whites. This array shall be the Lustr array as

13 manufactured by Electronic Theatre Controls, or approved equal a. Measured brightness of the Lustr array shall be greater than 6,500 field lumens b. Source Four LED Series 2 Tungsten HD 1. Mint, red, orange, blue, and indigo in an array designed to provide a variable white-light adjustable from 2700K to 6500K. (Designed for highest CRI and output between 2700K and 4500K) This array shall be the Tungsten HD array as manufactured by Electronic Theatre Controls, or approved equal a. Measured brightness of the Tungsten HD array shall be greater than 10,000 field lumens c. Source Four LED Series 2 Daylight HD 1. Mint, red, blue, and indigo in an array designed to provide a variable white-light adjustable from 2700K to 6500K. (Designed for highest CRI and output between 4000K and 6500K)This array shall be the Daylight HD array as manufactured by Electronic Theatre Controls, or approved equal a. Measured brightness of the Daylight HD array shall be greater than 10,000 field lumens J. Dimming 1. The LED system shall use 15-bit nonlinear scaling techniques for highresolution dimming. 2. At least four different dimming curve options shall be accessible at the fixture' s User Interface a. Incandescent b. Standard c. Linear d. Quick 3. Dimming curves shall be optimized for smooth dimming over longer timed fades. 4. The LED system shall be digitally driven using high-speed pulse width modulation (PWM) 5. LED control shall be compatible with broadcast equipment in the following ways: a. PWM control of LED levels shall be imperceptible to video cameras and related equipment b. PWM rates shall be adjustable by the user at the fixture if necessary to avoid any visible interference to video cameras and related equipment K. Control and User interface 1. The fixture shall be USITT DMX 512A-compatible via In and Thru 5-pin XLR connectors 2. The fixture shall be compatible with the ANSI RDM E1.20 standard

14 a. All fixture functions shall accessible via RDM protocol for modification from suitably equipped control console b. Temperature sensors within the luminaire shall be viewable in real time via RDM c. Fixtures not offering RDM compatibility, feature set access or temperature monitoring via RDM shall not be compatible 3. The fixture shall be equipped with multi-line LCD display for easy-to-read status reports and configuration changes 4. The fixture shall be equipped with a six-button user-interface 5. The fixture shall offer multiple DMX input profile options to include: a. RGB - control of all individual LED colors via a three-channel profile 1. Red, Green, Blue b. HSI control of all individual LED colors via a three-channel profile 1. Hue, Saturation, Intensity c. HSIC control of all LED colors via a four-channel profile 1. Hue, Saturation, Intensity and Color Point a. Color point provides variable color temperature settings d. Direct control of each individual color channel via an independent channel e. Studio Control of the fixture in a white-light 3 channel profile 1. Intensity, Color Temperature, +/- Green (Tint) a. Without DMX the fixture can master other Source Four LEDs and Desire fixtures that are connected via 5 pin XLR DMX cables f. A variable-rate strobe channel shall be provided 6. The fixture shall offer three output settings a. Boost mode - powers LEDs at maximum intensity and provides no compensation against LED droop' or intensity loss b. Regulated mode slightly restricts maximum LED intensity levels to compensate against LED droop c. Protected mode further restricts maximum LED intensity levels to compensate against LED droop and offer color consistency at highest permissible ambient temperatures (40C) d. Fixtures that do not provide regulated and protected operation modes are not acceptable 7. The fixture shall offer additional user-definable options to including but not limited to a. Display time out options b. Loss of data behavior options c. White point settings d. Red-shift option for tungsten dimming emulation 8. The fixture shall offer five Quick Set-Ups to allow user to rapidly select different combinations of the numerous user options based on the desired usage situation, to include: a. General for most situations

15 b. Stage when emulating incandescent fixtures is desired c. High Impact when maximum output and effect is desired d. XT Arch when color consistency and architectural characteristics are desired. e. Studio - when DMX or stand-alone of white light output is required with intensity, color temperature and color tint control parameters 9. The fixture shall offer stand-alone functionality eliminating the need for a console a. Fixture shall ship with 24 preset colors accessible as a stand-alone feature b. Fixture shall ship with 12 sequences accessible as a stand-alone feature c. Each color and sequence can be modified by the end user d. Fixtures can be linked together with standard DMX cables and controlled from designated master fixture 1. Up to 32 fixtures may be linked e. Fixtures in a stand-alone state shall restore to the settings present prior to power cycling, eliminating the need for reprogramming f. Fixtures without stand-alone operation features described above shall not be acceptable 10. The fixture shall be capable of copying all performance settings to other fixtures of the same type via a 5 pin XLR DMX cable 2.20 Source Four LED CYC Adapter A. General 1. The adapter shall work with all Source Four LED light engines 2. The adapter shall provide an evenly distributed light output when used in combination across large, flat surfaces B. Physical 1. The unit shall be constructed of rugged, die cast aluminum, free of burrs and pits, as well as injection molded ABS components; finished in black 2. Any exposed optics (excludes mirrors) shall be constructed out of heat and impact resistant poly-carbonate material 3. The unit shall attach securely to all Source Four LED light engines C. Optical 1. Unit should be able to be placed as close as 2 Ft. from the illuminated surface 2. Unit should be able to be top or bottom mounted 3. Unit should be able to achieve a 2:1 spacing 4. Unit should be able to light a 40 Ft. cyclorama with a top and bottom hang 5. Unit should maintain approximately 30% efficiency from source lumens to total field lumen output 2.21 Source Four LED Profile fixture D. General

16 1. The fixture shall be a color-mixing high-intensity LED illuminator with DMX control of intensity and color. The fixture shall be a Source Four LED as manufactured by Electronics Theatre Controls, Inc. or approved equal. 2. All LED fixtures shall be provided by a single manufacturer to ensure compatibility 3. The fixture shall be UL 1573 listed for stage and studio use 4. The fixture shall comply with the USITT DMX-512A standard E. Physical 1. The unit shall be constructed of rugged, die cast aluminum, free of burrs and pits, finished in black. 2. The following shall be provided: a. Lens secured with silicone shock mounts b. Shutter assembly shall allow for +/-25 rotation c. 20 gauge stainless steel shutters d. Interchangeable lens tubes for different field angles with Teflon guides for smooth tube movement e. Sturdy integral die cast gel frame holders with two accessory slots, and a top-mounted, quick release gel frame retainer f. Rugged steel yoke with two mounting positions allowing rotation of the fixture within the yoke g. Positive locking, hand operated yoke clutch h. Slot with sliding cover for motorized pattern devices or optional iris 3. The housing shall have a rugged black powder coat finish a. White or silver/gray powder coat finishes shall be available as color options b. Other powder coat color options shall be available on request 4. Power supply, cooling and electronics shall be integral to each unit. 5. The unit shall ship with: a. Theatrical-style hanging yoke as standard b. 5' Neutrik PowerCon to Edison power cable as standard c. Gate diffuser d. A-size pattern holder 6. Available options shall include but not be limited to: a. Bare-end, Stage-Pin or Twist-lock type-equipped power leads b. PowerCon to PowerCon cables for fixture power linking c. Smooth Wash Diffuser for overlapping beams of light from multiple fixtures F. Optical 1. The light beam should have a 2-to-1 center-to-edge drop-off ratio 2. The unit shall provide, but not be limited to: a. Low gate and beam temperature b. Sharp imaging through a three-plane shutter design 3. The unit shall provide, but not be limited to: a. 5, 10, 14, 19, 26, 36, 50, 70 and 90 degree field angles

17 b. High-quality pattern imaging c. Sharp shutter cuts without halation d. Shutter warping and burnout in normal use shall be unacceptable e. Adjustable hard and soft beam edges 4. 19, 26, 36, and 50 degree units shall have optional lens tubes available for precision, high-contrast imaging. G. Environmental and Agency Compliance 1. The fixture shall be ETL and cetl LISTED and/or CE rated, and shall be so labeled when delivered to the job site. 2. The fixture shall be UL LISTED to the UL1573 standard for stage and studio use 3. The fixture shall be rated for IP-20 dry location use. H. Thermal 1. Fixture shall be equipped with a cooling fan. a. Fan speed control via a DMX channel shall be possible b. Fan speed software shall permit the fixture to override DMX fan speed setting to prevent heat damage to the fixture 2. The fixture shall utilize advanced thermal management systems to maintain LED life to an average of 70% intensity after 50,000 hours of use a. Thermal management shall include multiple temperature sensors within the housing to include: 1. LED array circuit board temperatures 2. Temperature sensors placed on each individual LED color circuit 3. Fixture ambient 4. CPU b. Fixture user shall permit monitoring of temperature sensors via a legible LCD multi-line backlit display c. Fixtures that do not provide active thermal monitoring of LED circuits and other temperature readings shall not be acceptable 3. The fixture shall operate in an ambient temperature range of -20 C (- 4 F) minimum, to 40 C (104 F) maximum ambient temperature. I. Electrical 1. The fixture shall be equipped with a 100V to 240V 50/60Hz internal power supply 2. The fixture shall support power in and thru operation a. Power in shall be via Neutrik PowerCon input connector b. Power thru shall be via Neutrik PowerCon output connector c. Fixture power wiring and accessory power cables shall be rated to support linking of multiple fixtures up to the capacity of a 15A breaker 3. The fixture requires power from a non-dim source

18 4. Power supply outputs shall have self-resetting current-limiting protection 5. Power supply shall have power factor correction J. LED Emitters 1. The fixture shall contain a minimum of five different LED colors to provide color characteristics as described in the Color Section below. 2. All LEDs used in the fixture shall be high brightness and proven quality from established and reputable LED manufacturers. a. Fixture shall utilize Luxeon Rebel LED emitters 3. Manufacturer of LED emitters shall utilize an advanced production LED binning process to maintain color consistency. 4. LED emitters should be rated for nominal 50,000-hour LED life to 70% intensity 5. All LED fixtures (100% of each lot) shall undergo a minimum eight-hour burn-in test during manufacturing. 6. LED system shall comply with all relevant patents K. Calibration 1. Fixture shall be calibrated at factory for achieve consistent color and intensity output between fixtures built at different times and/or from different LED lots or bins a. Calibration data shall be stored on the LED array as a permanent part of on-board operating system b. All arrays, including replacement arrays shall be calibrated to the same standard to insure consistency c. Fixtures not offering LED calibration shall not be acceptable L. Color 1. The fixture shall utilize a minimum of 60 LED emitters 2. The fixture shall be available in specialized LED arrays as outlined below: a. Source Four LED Lustr+ 1. Red, Amber, Green, Cyan, Blue, Indigo and White LEDs in an array designed for broad spectrum color, light tints, and variable whites. This array shall be the Lustr+ array as manufactured by Electronic Theatre Controls, or approved equal a. Measured brightness of the Lustr+ array shall be greater than 4,000 field lumens b. Source Four LED Tungsten 1. All Warm White LEDs in an array designed for nonvariable single color high-output, warm white light. This shall be the Studio Tungsten array as manufactured by Electronic Theatre Controls, or approved equal a. Measure brightness of the Studio tungsten array shall be greater than (TBD) field lumens c. Source Four LED Daylight

19 1. All Cool White LEDs in an array designed for nonvariable single color high-output, cool white light. This shall be the Studio Daylight array as manufactured by Electronic Theatre Controls, or approved equal a. Measure brightness of the Studio Daylight array shall be greater than (TBD) field lumens M. Dimming 1. The LED system shall use 15-bit nonlinear scaling techniques for highresolution dimming. 2. At least four different dimming curve options shall be accessible at the fixture' s User Interface a. Incandescent b. Standard c. Linear d. Quick 3. Dimming curves shall be optimized for smooth dimming over longer timed fades. 4. The LED system shall be digitally driven using high-speed pulse width modulation (PWM) 5. LED control shall be compatible with broadcast equipment in the following ways: a. PWM control of LED levels shall be imperceptible to video cameras and related equipment b. PWM rates shall be adjustable by the user at the fixture if necessary to avoid any visible interference to video cameras and related equipment N. Control and User interface 1. The fixture shall be USITT DMX 512A-compatible via In and Thru 5-pin XLR connectors 2. The fixture shall be compatible with the ANSI RDM E1.20 standard a. All fixture functions shall accessible via RDM protocol for modification from suitably equipped control console b. Temperature sensors within the luminaire shall be viewable in real time via RDM c. Fixtures not offering RDM compatibility, feature set access or temperature monitoring via RDM shall not be compatible 3. The fixture shall be equipped with multi-line LCD display for easy-toread status reports and configuration changes 4. The fixture shall be equipped with a six-button user-interface 5. The fixture shall offer multiple DMX input profile options to include: a. RGB - control of all individual LED colors via a three-channel profile 1. Red, Green, Blue b. HSI control of all individual LED colors via a three-channel profile 1. Hue, Saturation, Intensity

20 c. HSIC control of all LED colors via a four-channel profile 1. Hue, Saturation, Intensity and Color Point a. Color point provides variable color temperature settings d. Direct control of each individual color channel via an independent channel e. Studio Control of the fixture in a white-light 3 channel profile 1. Intensity, Color Temperature, +/- Green (Tint) a. Without DMX the fixture can master other Source Four LEDs and Desire fixtures that are connected via 5 pin XLR DMX cables f. A variable-rate strobe channel shall be provided 6. The fixture shall offer three output settings a. Boost mode - powers LEDs at maximum intensity and provides no compensation against LED droop' or intensity loss b. Regulated mode slightly restricts maximum LED intensity levels to compensate against LED droop c. Protected mode further restricts maximum LED intensity levels to compensate against LED droop and offer color consistency at highest permissible ambient temperatures (40C) d. Fixtures that do not provide regulated and protected operation modes are not acceptable 7. The fixture shall offer additional user-definable options to including but not limited to: a. Display time out options b. Loss of data behavior options c. White point settings d. Red-shift option for tungsten dimming emulation 8. The fixture shall offer five Quick Set-Ups to allow user to rapidly select different combinations of the numerous user options based on the desired usage situation, to include: a. General for most situations b. Stage when emulating incandescent fixtures is desired c. High Impact when maximum output and effect is desired d. XT Arch when color consistency and architectural characteristics are desired. e. Studio - when DMX or stand-alone of white light output is required with intensity, color temperature and color tint control parameters 9. The fixture shall offer stand-alone functionality eliminating the need for a console a. Fixture shall ship with 24 preset colors accessible as a standalone feature b. Fixture shall ship with 12 sequences accessible as a standalone feature c. Each color and sequence can be modified by the end user

21 d. Fixtures can be linked together with standard DMX cables and controlled from designated master fixture 0. Up to 32 fixtures may be linked e. Fixtures in a stand-alone state shall restore to the settings present prior to power cycling, eliminating the need for reprogramming f. Fixtures without stand-alone operation features described above shall not be acceptable 2.22 Diversity Series LED RGBWA Fixtures O. DVW-5 Diversity Series LED Wash fixture with 36 x 15-watt RGBWA 5-in-1 colorchanging LED array, complete with pipe clamp, double yoke, 5-pin XLR DMX in/out, and PowerCON in/out. B. DVW-5Z Diversity Series LED Zoom-Wash fixture with 18 x 15-watt RGBWA 5-in-1 color-changing LED array, 5 to 65 Zoom, complete with pipe clamp, double yoke, 5- pin XLR DMX in/out, and PowerCON in/out. C. DVW-6M Diversity Series LED Moving Wash fixture with 36 x 18-watt RGBWA+ UV 6- in-1 color-changing LED array, Pan and Tilt, 5 to 65 Zoom, complete with pipe clamp, double yoke, 5-pin XLR DMX in/out, and PowerCON in/out. D. DVW-UV Diversity Series 54 x 3-watt UV-LED Wash fixture, complete with pipe clamp, double yoke, 5-pin XLR DMX in/out, and PowerCON in/out. E. DVS-5 Diversity Series 1-meter LED Striplight with 18 x 15-watt RGBWA 5-in-1 colorchanging LEDs, complete with floor trunnions / hanging brackets, pipe clamp, 5-pin XLR DMX in/out, and PowerCON in/out. F. DVS-UV Diversity Series 1-meter LED Striplight with 36 x 3-watt UV-LEDs, complete with floor trunnions / hanging brackets, pipe clamp, 5-pin XLR DMX in/out, and 36 Edison G. DVB-6 Diversity Series Battery operated LED Up-Light with 4 x 18-watt RGBWA+UV 6-in-1 color-changing LED array (charging Road Case available). 3.1 Provide the following: 1. Items I. IV. As the base bid I. Power Control System to consist of: A. DR A SR Black Sensor3 48-Module Dimmer Rack - Designed for 3 phase 4 wire and ground operation at a maximum of 800A, 120/208V, 60Hz AC A SR3-48 DOOR - Black SR3-48 Locking Door with Filter A1003 CEM3 - CEM3 Control Module 1 Custom Item Custom label for dimmer rack A1031 D20E - Dual 20A Dimmer Module, 500µs rise time (88 Dimmers) R20AF Relay Modules (8 Relays) (Location determined by owner as

22 needed II. Control System to consist of: A. Existing Control Console B. Equipment Rack 1 QUOTE RACK - Black 19" rack sized as job requires and to include: quad power box, and blank panels to fill 1 QUOTE- DOOR - Door for Rack A1013 ERN2-RM ERn2 Enclosure Rack-mount V A1005 ERN-RPS - ERn Redundant Power Supply Module - Cannot be used with ERn-NET A1009 P-ACP2 - Paradigm Architectural Control Processor A1001 P-SPM - Paradigm Station Power Module - supports 32 stations and (1) 500m wire segment A2008 PATCH PANEL 24X - 2U 19" rack-mount patch panel with 24 open slots 23 N2027 Cat5e Modular Jack for above Patch Panel 1 PJJ1002 UTP Pass through for patch panel 1 SGE1062 MAP BR2-2U Brush Grommet Panel 24 N4035 2' CAT5 Patch cable, black 1 SGN1129-M CISCO SG300-28PP - Cisco Switch - 24 RJ-45 ports of 10/100/1000 PoE+ (180W total allowance) - 2 RJ-45 ports of 10/100/ combo ports of RJ-45 or mini-gbic/sfp 1 PJPS1012 MAP 1000R VA / 750W rack-mount UPS C. Multi Box Type 1 (Booth) 1 ECPB N/N/N - ETCNet / ETCNet / ETCNet Station with: 2 - RJ-45 (568B) Connectors in XLR cases A1039 ECPB PB3 - ETC 3-gang Surface Mount Back Box (3.5" deep) D. Multi Box Type (SMP Catwalk) 2 QUOTE ECPB DMX Out / NET / NET - DMX Out / Net / Net Control Plug-in Station with: 1 - XLR-5FDM3 DMX Out Connector(s) 2 - RJ-45 (568B) Connector in XLR case A1040 ECPB PB4 - ETC 4-gang Surface Mount Back Box (3.5" deep) A1050 -U - U-Bolt Pipe-mounting Assembly (1 pair) E. Multi Box Type N-GIB (1st, 2nd, 3rd electrics) 3 Custom Item Net Grid Iron Junction Box with 75 Proplex Net cable secured to existing SO cable to extend from grid iron to SR pipe batten end. (Plug into Portable gateway(s) listed below)

23 F. Multi Box Type 4 (Booth) 1 QUOTE ECPB DMX In / DMX IN / DMX IN - DMX Input / DMX Input / DMX Input Control Plug-in Station with: 3 - XLR-5MDM3 DMX In Connector(s) Labeled as DMX-In 1 Dimmer, DMX-In 2 Catwalk, DMX-In 3 SMP A1039 ECPB PB3 - ETC 3-gang Surface Mount Back Box (3.5" deep) G. Portable Gateways A1103 N3T2G-2F - Portable (Touring) Net3 Only Two Port Output Gateway to Contain: 2 - XLR-D5F, 5-pin Female XLR connectors with hanger bracket for c-clamp or U-bolt Configure both connectors as Outputs, DMX universe 1 Install in Catwalk, 1 st, 2 nd, 3 rd Electrics with all necessary cables as required A CC - Black C-Clamp A SC - Safety Cable Black III. Architectural Control System to consist of: A. Portable (Booth) A1532 P-T S7-PE - Paradigm 7" Ethernet Portable Touchscreen Station to include: - 7" Black Portable Touchscreen - 10' Ethercon to RJ-45 cable 1 SGM76 25' Network Cable (Cat 5, Neutrik Ethercon to RJ45) B. Entry Station (Replace as existing) 4 QUOTE UH10002-_Z - Standard Color (Color TBD) 1-gang faceplate assembly to include the following: 2 - Select Switch Standard nomenclature as On, Off, LED back light shall be illuminated Green when preset is in the Off state B2004 UH gang, 1-button electronics assembly w/ir Port A SBB1 - Unison 1-gang surface-mounted back box C. LCD (SMP) A P-T S7-4 - Paradigm 7" Touchscreen Station to include: - 7" Black Touchscreen Assembly - Mounting Collar - LinkConnect/ Ethernet termination kit A1503 P-LCD-SBB - Paradigm surface mount touchscreen back box

24 IV. Accessories 1 Portable Uninterruptable Power Supply capable of powering existing control console and monitors for up to 1-hour. - Install in booth for existing control console 1 Low Voltage control cable as necessary for all DMX, Paradigm and Network System(s) - Provide and terminate as necessary -Installation by the Electrical Contractor 6 5-pin XLR Terminator V. Option 1 RFR A1022 NET3-RFR - Net3 Radio Focus Remote Universal Frequency to Include: 1 - Base Station with: 1 - USB Port to connect to Console 1 - Ethercon Ethernet Port to connect to Lighting Network 1 - Hand Held Transmitter with: 1-24 button Backlit keypad 2 - Encoder wheels 1 - Mini USB port for Recharging Battery 1 - ON/Off Switch 1 - USB A to B Cable 1 - USB A to Mini B Cable Wall-Wart Power Supply Belt Clip VI. Option 2 Fixtures Option 2 fixtures shall be priced per each fixture complete including accessories listed, final quantities of each fixture type to be determined based on final project costs. 1 ETC Series 2 LED Ellipsoidal, each fixture to include: 1-Choice of one 19, 26, 36 Lens Tube TBD 1-Safety Cable 1-10 DMX cable 5-P XLR 1-10 PowerCon to PowerCon Jumper 1-3 PowerCon input cable with stage pin connector 1- Pipe Clamp 1-Soft Focus Diffuser 1-A size Pattern Holder 1 ETC ColorSource Spot LED Ellipsoidal, each fixture to include:

25 1-Choice of one 19, 26, 36 Lens Tube TBD 1-Safety Cable 1-10 DMX cable 5-P XLR 1-10 PowerCon to PowerCon Jumper 1-3 PowerCon input cable with stage pin connector 1- Pipe Clamp 1-Soft Focus Diffuser 1 ETC ColorSource Linear 4, Deep Blue, each fixture to include: 4-Medium Round Diffuser 2-Safety Cable 1-10 DMX cable 5-P XLR 1-10 PowerCon to PowerCon Jumper 1-3 PowerCon input cable with stage pin connector 2- Trunnions 2- Pipe Clamp 1 DVW-5 Diversity Series LED Wash fixture RGBWA 1-10 DMX cable 5-P XLR 1-10 PowerCon to PowerCon Jumper 1-3 PowerCon input cable with stage pin connector 1-Pipe Clamp 1-Double yoke 1-5-pin XLR DMX in/out plug in panel 1-PowerCON in/out plug in panel 1 DVW-5Z Diversity Series LED Zoom Wash fixture RGBWA 1-10 DMX cable 5-P XLR 1-10 PowerCon to PowerCon Jumper 1-3 PowerCon input cable with stage pin connector 1-Pipe Clamp 1-Double yoke 1-5-pin XLR DMX in/out plug in panel 1-PowerCON in/out plug in panel 1 DVS-5 Diversity Series 1-meter LED Striplight 1-10 DMX cable 5-P XLR 1-10 PowerCon to PowerCon Jumper 1-3 PowerCon input cable with stage pin connector 2-floor trunnions / hanging brackets 2-Pipe Clamps 1-5-pin XLR DMX in/out plug in panel 1-PowerCON in/out plug in panel End BOM