Installation and Operating Guide Warranty. Model Number HCS5650 HD Integrator Box System. t a b l e o f c o n t e n t s. installer quick setup guide

Transcription

1 Installation and Operating Guide Warranty Model Number HCS5650 HD Integrator Box System t a b l e o f c o n t e n t s page 5 installer quick setup guide page 75 Copyright 008, LG Electronics U.S.., Inc. Zenith and the lightning Z logo are registered trademarks of Zenith Electronics Corporation

2 For Customer Support/Service please call: RECORD THE MODEL NUMBER The model and serial number of this HD Integrator Box System are located on the side of the cabinet. For future reference, we suggest that you record the serial number here: MODEL NO. HCS5650 SERIL NO. CUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BCK). NO USER SERVICEBLE PRTS INSIDE. REFER TO QULIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WRNING: TO PREVENT FIRE OR SHOCK HZRDS, DO NOT EXPOSE THIS PRODUCT TO RIN OR MOISTURE. IT IS FORBIDDEN TO CONNECT THIS TV TO NY TELECOMMUNICTION NETWORK / TELEPHONE. NOTE TO CBLE TV INSTLLER: This reminder is provided to call the CTV system installer s attention to rticle 80-0 of the National Electric Code (U.S..). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. REGULTORY INFORMTION: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 5 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. CUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user s authority to operate the equipment Marketed and Distributed in the United States by LG Electronics U.S.., Inc. 000 Millbrook Drive, Lincolnshire, IL

3 CUTION: Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation. Unauthorized modification could void the user s authority to operate this product. COMPLINCE: The responsible party for this product s compliance is: LG Electronics U.S.., Inc., 000 Millbrook Drive Lincolnshire, IL 60069, US. Phone: WRNING: pparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. CUTION: THESE SERVICING INSTRUCTIONS RE FOR USE BY QULIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT PERFORM NY SERVICING OTHER THN THT CONTINED IN THE OPERTING INSTRUCTIONS UNLESS YOU RE QULIFIED TO DO SO. CUTION: When used outside of the U.S., it may be used HR cord with fitting of an approved agency is employed. (When used outside of U.S., other power supply cords may be used if the cord is approved by the local regulating agency.) DISCONNECTING DEVICE FROM MINS: Main plug is the disconnecting device. The plug must remain readily operable. n apparatus with CLSS I construction shall be connected to a Mains socket outlet with a protective earthing connection. IMPORTNT SFEGURDS FOR YOU ND YOUR NEW PRODUCT YOUR PRODUCT HS BEEN MNUFCTURED ND TESTED WITH YOUR SFETY IN MIND. HOWEVER, IMPROPER USE CN RESULT IN POTENTIL ELECTRICL SHOCK OR FIRE HZRDS. TO VOID DEFETING THE SFEGURDS THT HVE BEEN BUILT INTO YOUR NEW PRODUCT, PLESE RED ND OBSERVE THE FOLLOWING SFETY POINTS WHEN INSTLLING ND USING YOUR NEW PRODUCT, ND SVE THEM FOR FUTURE REFERENCE. OBSERVING THE SIMPLE PRECUTIONS DISCUSSED IN THIS MNUL CN HELP YOU GET MNY YERS OF ENJOYMENT ND SFE OPERTION THT RE BUILT INTO YOUR NEW PRODUCT. PGE

4 IMPORTNT SFETY INSTRUCTIONS. Read these instructions.. Keep these instructions.. Heed all warnings.. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. polarized plug has two blades with one wider than the other. grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 0. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.. Only use attachments/accessories specified by the manufacturer.. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. PORTBLE CRT WRNING. Unplug this apparatus during lightning storms or when unused for long periods of time.. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or object have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Outdoor ntenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. rticle 80 of the National Electrical Code (U.S..), NSI/NFP 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. Example of Grounding ccording to National Electrical Code Instructions Ground Clamp ntenna Lead in Wire ntenna Discharge Unit (NEC Section 80-0) Electric Service Equipment Grounding Conductor (NEC Section 80-) Ground Clamps PGE NEC - National Electrical Code Power Service Grounding Electrode System (NEC rt 50, Part H)

5 Table of Contents The table of contents lists the pages to go to for setting up the features for the end user. Safety Warnings Important Safety Instructions Table of Contents Step. HD Integrator Box System Installation and Connections Setup Checklist Installation/Connections Overview Ventilation Installation Overview UX Controller: Connection and Placement IR Receiver & IR Bracket Installation TV and other Equipment Hookup ntenna Cable Service RS-C Control Connections Viewing Equipment Setup Computer PC Hookup (DVI) udio Connection - Digital udio Optical Connections..6 Menus and Displays Overview On-Screen Menus Overview Pillow Speaker Setup Other Menus and On-Screen Displays User Remote Control Key Functions Installer Remote Control Key Functions Step. Channel Search and Reception Setup uto Program (Do a Channel Search) Channel List Channel Labels Setup Unstable Screen Checking the Strength of Digital Signal Step. Customize the TV s Features Clock Setup V-Chip Caption Menu Sound Menu Language Control Set ID Picture Menu Managing The Channel Banks Commercial Mode Setup Cloning Connections/Learning Setup Clone Programmer Learning Setup Cloning Connections/Teaching Setup Installer Menu Reference TV/STB ux Input Configuration RS- Monitor Requirments/RS- Troubleshooting...69 RS-C Control Troubleshooting Installer Quick Setup Guide Glossary of Terms Warranty Back Cover Optional Installer Remote Control for Model No. Series HCS5650 The Installer remote control is NOT included with the HD Integrator Box System. Purchase the Optional Installer's Remote and Clone Programmer To perform a normal installation set up, you need an installer's remote and the LT00 Quickset II Clone Programmer both are shown and described in later sections. See your Zenith/LG dealer if you wish to purchase the Installer remote and LT00. The installer remote allows access to the Installer menus, User menus in the Manual Channel Set options on the Setup menu. The installer remote has Menu, Select, and djust Keys. The LT00 Quickset II Clone Programmer is used to duplicate a TV/STB setup and install it on another identical TV/STB. *Note: Design and specifications are subject to change without prior notice. PGE 5

6 Setup Checklist Installation Overview Unpack the HD Integrator Box System and all accessories. Determine installation location for the HD Integrator Box System, TV stand or mount. Determine mounting and installation requirements. If used, C Power source outlet, ntenna/cable service connectors, any external equipment required for system or TV operation, all necessary cables, wires, connectors and any other additional required hardware, etc. Installation Overview & System Setup: Questions to Consider Before Installation VES Bracket Does the VES Bracket have to be mounted to the TV? Y: Install VES Bracket on TV following the instructions supplied with the bracket. Yes No TV Stand Does the TV have to be mounted on the stand? Y: Mount the TV on the stand following the instructions provided with the TV stand. Yes No Installer's Remote Control Does the Installer have the optional Installer's remote control available to use to set up the TV (This is a must for TV setup.)? Yes No Master TV Setup Will the Master TV's features setup be cloned and copied to other identical HD Integrator Box Systems? Yes No LT00 Quickset II Clone Programmer To copy the TV's setup, the installer will need a clone programmer. Is there a Zenith LT00 Clone Programmer available? Yes No End-User Remote Control Will a remote control be provided to the end user to operate the TV? (The remote is included with the TV.) Yes No End-User Menu ccess Will the end-user have access to all the menus on the TVs from the front panel? Yes No HD Integrator Box System Setup Checklist. Install the HD Integrator Box System where it will be used. Prior to Operation The HD Integrator Box System must be connected to all external antenna/cable, video, and audio source equipment. See page 5, Table of Contents.. Make all external source equipment connections. See pages Connect the HD Integrator Box System to a standard 0V, 60 Hertz, C power source. See page.. Turn on the TV and all source equipment. Review TV Setup Options in the Installer's Menu Section The Installer's menu includes a number of options for the master TV's setup that enable the installer or system administrator to devise a unique system using the many different options and variables available. See Installer's menus section. Master TV Features Setup for Cloning Overview Set up Installer's remote control, see page. Do a Channel Search, see page. Channel List. Channel Label. Video/picture appearance options setup, see Picture menu. udio/sound options setup, see Sound menu. Set up all other features. See page 5, Table of Contents, for a list of features available on this HD Integrator Box System. Clone Master TV's Setup See Clone Programmer section. *Note: fter installing a PPV card in the HCS5650 be sure to disconnect the C power cord for 5 seconds and reconnect it. Supplied ccessories List - 5 ft. HDMI to DVI-M Cable - ft. HDMI to DVI-F Cable - 5 ft. RS- Control Cable - 6 ft. C Power Cord (Hospital Grade) - ft. IR Receiver Cable - Screws & Wall Mount Bracket (5- Required) - 6 ft. Stereo Plug to Stereo Plug(.5mm) - Installation Guide - User Remote Control & Batteries (Included) - Installer Remote Control & Batteries (Optional) PGE 6

7 Installation/Connections Overview To hook up source equipment, see below and also refer to the Table of Contents on page 5; shows pages to go to for equipment hookup options. PILLOW INT C OUT 8 C IN 0V~60Hz REMOTE IN UDIO IN UDIO OUT SERVICE PILLOW JCK IN UX (V DC 0m) CONTROL DIGITL VIDEO IN DIGITL VIDEO OUT DIGITL UDIO OUT (OPTICL) DISPLY CONTROL SPEKER SWITCH Used to select the speaker output. *Note: If Pillow Speaker is selected, no Sound will be heard from TV speakers. Switch (NORML SPEKER or PILLOW SPEKER.) M.P.I Interface Remote In udio In udio Out SERVICE Port C Out PILLOW INT C OUT 8 C IN 0V~60Hz REMOTE IN UDIO IN UDIO OUT SERVICE PILLOW JCK IN (V DC 0m) UX CONTROL DIGITL VIDEO IN DIGITL VIDEO OUT DIGITL UDIO OUT (OPTICL) DISPLY CONTROL UX Control Cable In PILLOW JCK IN Used to connect to pillow speaker (V DC 0m) Digital Video, In Digital Video Out Digital udio Out (Optical) Display Control C In HCS5650 front panel controls and LED functions HCS5650 POWER STTUS RESET UPDTE B POWER STTUS RESET UPDTE C D B C D POWER LED The POWER LED illuminates while the display panel is on. The LED is off when the display panel is off. STTUS LED The STTUS LED flashes while the program is running. RESET Press RESET to start the program that re-initializes the HCS5650. UPDTE Press UPDTE to allow software to be updated. To start the download program, press and release the RESET button while holding down the UPDTE button. PGE 7

8 Ventilation The HCS5650 Integrator Box as well as LCD monitors(m70c-bh and M0C-BH) generate heat during operation and need to be provided with adequate ventilation to assure continued reliable operation. See recommendations below. Ventilation Clearance Proper clearance for air to flow around the HCS5650 Integrator Box must be provided. Monitor Ventilation Be sure proper ventilation is provided for the monitor, see monitor installation guide for specified ventilation requirements. Vent Holes There are ventilation holes on four sides of the the HCS5650 box provided for ventilation cooling. a. If the box is mounted vertically, the vents on the sides should be located on the top and bottom for free vertical air movement. b. If the box is mounted horizontally, the vents should be located at the sides and top of the enclosure (never mount the box with vents facing down). Vent Holes Vent Holes The vent holes should never be blocked or obstructed to airflow but have an unimpeded path through any enclosure back to room temperature air. Vent Holes The unit and its venting, should not be installed near heat sources such as radiators or heating ducts. Vent Holes 5 If the unit is placed in an enclosure, tests should be run to confirm that the ambient temperature around the unit under normal expected operating conditions is stable and does not exceed 0 degrees Celsius (0F). This can be determined by placing a thermometer near the air intake vents in the proposed enclosure and measuring the temperature every hour, under normal operating conditions, until two successive readings repeat. If temperature does not stabilize but keeps increasing above 0F, ventilation is inadequate and needs to be improved. lways provide adequate air space between the ventilation areas and adjacent structures. Vent Holes *Note: In addition to the ventilation requirements shown, be sure to allow enough clearance ( - 5 ) for wiring clusters attached to the Integrator Box. PGE 8

9 Ventilation / Installation Overview Vertical Installation (Wall Mount) Using Supplied ngled L-Brackets Two angled brackets are provided so that the Integrator Box can be mounted on a flat vertical surface, like a wall. Install the two angled brackets and the screws provided. Mount Integrator Box on the wall using five appropriate screws. *Note: The brackets are designed to be mounted to typical 6 spaced wall studs. Do not mount the Integrator Box to a weak wall surface. If wall studs are not available, use some other appropriate fastening system. Monitor/Integrator Box Wall Mounting System The LCD monitor and Integrator Box can be mounted to a wall using an optional Monitor/Integrator Box wall mounting system. For further information on the mounting system, see your LG dealer. PGE 9

10 UDIO (MONO) V INPUT S-VIDEO P UDIO R L UDIO INPUT RS-C R L (+) ( ) ( ) (+) UX Controller: Connection and Placement Connect the UX Controller to allow the Integrator Box to operate your UX device. Connect the UX Controller to the UX CONTROL cord on the TV/STB. Place the UX Controller under and in front of the UX device. The UX Controller must extend just out in front of the infrared sensor on the UX device. *Note: If the infrared sensor is not marked on your UX device, shine a flashlight into the front panel of the UX device to locate the sensor. PILLOW INT C OUT 8 C IN 0V~ 60Hz REMOTE IN UDIO IN UDIO OUT SERVICE PILLOW JCK IN UX (V DC 0m) CONTROL DIGITL VIDEO IN DIGITL VIDEO OUT DIGITL UDIO OUT (OPTICL) DISPLY CONTROL Connections Panel DVD (Front View) UX Controller IR Sensor DVD (Side View) to / IR Receiver & IR Bracket Installation Install the IR Receiver and Bracket ssembly to the back of the monitor using the method described below. Monitor R L VIDEO Y PB R COMPONENT(80i/80p) RGB-PC INPUT (DVD INPUT) (VG/SVG/XG/SXG) EXTERNL SPEKER (8 ) C INPUT IR Receiver IR Bracket PILLOW INT C OUT 8 C IN 0V~ 60Hz REMOTE IN UDIO IN UDIO OUT SERVICE IR Receiver & Bracket Installation PILLOW JCK IN UX (V DC 0m) CONTROL DIGITL VIDEO IN DIGITL VIDEO OUT DIGITL UDIO OUT (OPTICL) DISPLY CONTROL Connections Panel THE IR RECEIVER UNIT IS PROVIDED. THIS WILL NEED TO BE MOUNTED ON THE MONITOR BCK WITH TWO-SIDED TPE. PGE 0

11 PILLOW INT PILLOW JCK IN (V DC 0m) REMOTE IN UX CONTROL DIGITL VIDEO IN UDIO IN UDIO OUT RS-C DIGITL VIDEO OUT DIGITL UDIO OUT (OPTICL) DISPLY CONTROL C OUT MX 8 960W C IN C 0V~ 60Hz ntenna Hookup Connect an off-air antenna to the HD Integrator Box System. Locate the ntenna/cable jack on the back of the HD Integrator Box System. Connect the antenna wire (Flat or Round) that runs from the wall to this jack, according to one of the diagrams shown to the right. PILLOW INT fter all connections are complete, plug in the TV. The HD Integrator Box System is designed to operate on C power. PILLOW JCK IN (V DC 0m) REMOTE IN UX CONTROL UDIO IN UDIO OUT DIGITL DIGITL VIDEO IN VIDEO OUT Connections Panel If the antenna is a 75 ohm RF cable, then no adapters are required. 00 to 75 ohm adapter is not included with the Zenith HD Integrator Box System. Flat Wire (00 ohm) 00/75 ohm dapter PILLOW INT REMOTE IN UDIO IN UDIO OUT PILLOW JCK IN UX (V DC 0m) CONTROL DIGITL VIDEO IN DIGITL VIDEO OUT Connections Panel RF Coaxial Wire (75 ohm) Mini glossary 75 OHM RF CBLE The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire sticking through the middle, and it screws onto the threaded jack on the back of the TV. 00 TO 75 OHM DPTER small device that connects a two-wire 00 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws on one end and a round opening with a wire sticking out on the other end. PGE

12 RJP INTERFCE REMOTE IN UX CONTROL DIGITL VIDEO IN UDIO IN UDIO OUT RS-C DIGITL VIDEO OUT DIGITL UDIO OUT (OPTICL) DISPLY CONTROL C OUT MX 8 960W C IN C 0V~ 60Hz Cable Service Hookup Connect cable service to the HD Integrator Box System. Locate the ntenna/cable jack on the back of the TV/STB. Connect the cable wire to the ntenna/cable jack according to one of the diagrams to the right. Cable TV Wall Jack PILLOW INT REMOTE IN UDIO IN UDIO OUT Connections Panel fter all connections are complete, plug in the TV. The HD Integrator Box System is designed to operate on C power. PILLOW JCK IN (V DC 0m) UX CONTROL DIGITL VIDEO IN DIGITL VIDEO OUT RF Coaxial Wire (75 ohm) Cable TV Wall Jack PILLOW INT REMOTE IN UDIO IN UDIO OUT PILLOW JCK IN (V DC 0m) UX CONTROL DIGITL VIDEO IN DIGITL VIDEO OUT Connections Panel Coaxial Wire RF (75 ohm) Mini glossary 75 OHM RF CBLE The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire sticking through the middle, and it screws onto the threaded jack on the back of the TV. 00 TO 75 OHM DPTER small device that connects a two-wire 00 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws on one end and a round opening with a wire sticking out on the other end. PGE

13 RS-C Control Connections Connect the Display Control (RS-C) port from the TV/STB to the display panel to control TV functions with RS-C commands PILLOW INT C OUT 8 C IN 0V~ 60Hz REMOTE IN UDIO IN UDIO OUT SERVICE PILLOW JCK IN (V DC 0m) UX CONTROL DIGITL VIDEO IN DIGITL VIDEO OUT DIGITL UDIO OUT (OPTICL) DISPLY CONTROL To Display Control Output Port Connections Panel To RS-C Input Port Typical LCD Display Panel ONCE THE RS-C CONNECTION IS MDE BETWEEN THE TV/STB ND THE DISPLY PNEL, THE DISPLY PNEL CN ONLY BE CON- TROLLED BY THE TV/STB. *Note: Some TV/Monitor installations will require RS- Null modem cable(s) with gender changers. PGE

14 Viewing Equipment Setup Connect the TV/STB to the display device that will be used to view the signal. n unswitched C power outlet is specifically provided on the TV/STB to plug the display panel into. LCD Display Panel Setup for use with the TV/STB Commercial Interface Control Box. Connect RS-C cable. (See previous page.) Connect IR Receiver cable to Remote In port. Connect the Cable Out jack to the display panel, typically the ntenna (In) jack. HCS5650 PTC INSTLLER MENU 000 INSTLLER SEQ 000 UPN FPG E0F PTC V CPU V Plug the display panel C power cord into the convenience C power outlet provided on the TV/STB. Plug the TV/STB C power cord into a standard 0V 60 Hz power outlet. Once power is applied to the TV/STB, the C power outlet is active. The LED on the display panel will turn red, indicating that the panel is in standby mode. ntenna Wall Jack FR Coaxial Wire (75ohm).5mm Stereo Plug with IR Receive DVI udio R - L.5mm Stereo Plug Use the user-supplied remote control to turn on the TV/STB. Connect ux Control IR Output as required of your system. PILLOW INT C OUT 8 C IN 0V~ 60Hz REMOTE IN UDIO IN UDIO OUT SERVICE PILLOW JCK IN (V DC 0m) UX CONTROL DIGITL VIDEO IN DIGITL VIDEO OUT DIGITL UDIO OUT (OPTICL) DISPLY CONTROL C Power Coad PGE

15 PILLOW INT REMOTE IN PILLOW JCK IN UX (V DC 0m) CONTROL DIGITL VIDEO IN UDIO IN UDIO OUT SERVICE DIGITL VIDEO OUT DIGITL UDIO OUT (OPTICL) DISPLY CONTROL C OUT 8 C IN 0V~ 60Hz Computer PC Hookup (DVI) Locate the computer DVI out port on the computer. Connect a computer cable between the computer and DIGITL VIDEO In on the TV/STB. Make PC udio connections as indicated to the up. UDIO IN DIGITL VIDEO IN fter all connections have been made, select the DIGITL VIDEO or source to display the PC image on the TV. PGE 5

16 udio Connection Digital udio Optical Connections PILLOW INT C OUT 8 C IN 0V~ 60Hz REMOTE IN UDIO IN UDIO OUT SERVICE PILLOW JCK IN (V DC 0m) UX CONTROL DIGITL VIDEO IN DIGITL VIDEO OUT DIGITL UDIO OUT (OPTICL) DISPLY CONTROL Connections Panel From Digital udio Optical Out Port To Digital udio Optical In Port Typical Digital udio mplifier System Digital udio Optical Output Connections to External mplifier Hook up a Digital udio mplifier System using the Digital udio Optical Out port, according to the diagram above. Select the Digital udio Optical input source on the mplifier. PGE 6

17 On-Screen Menus Overview Descriptions of the menus and on-screen displays. Menu Name Page Description ON-SCREEN MENUS CHNNEL MENU djusts the basic operational features of the TV. uto Program utomatically finds and stores active channels to scroll through using Channel Up/Down. Channel List Manually picks and chooses which active channels will appear when using Channel Up/Down. Channel Label Labels the channels with their network names (BC, CBS, HBO, etc.). Fine Tune 5 utomatically adjusts the picture for optimum appearance. Signal Strength 5 Reveals the strength of the incoming digital signal. SETUP MENU Time 6 Sets the time. V-Chip Sets up restrictions or changes the password for Parental Control. CPTION MENU 8 Chooses analog and digital captioning options. SOUND MENU 0 Sets up the sound. Options are: Mode, Balance, Digital Output, uto Volume, Multi-Track, Internal Speaker. Menu Language Picks the language the on-screen menus will appear in. Menu Transparency Selects the degree of menu opacity. Set ID Specifies the TVs identity. PICTURE MENU 5 Sets up the picture appearance. Options are: Mode, Color Temperature, Screen Format, Noise Reduction, Film Mode. Volume Sleep Timer SP Captions larm Guide Channel Preview -> V-Chip Info 9 OTHER MENUS ND ON-SCREEN DISPLYS Shows current sound level. Sets a time the TV will turn off. Selects MTS sound: Mono, Stereo, and SP in analog mode. Change the audio language in DTV mode. Selects Caption/Text options. Set a time for the TV to turn itself on. View DTV program information. With Guide displayed, press Info for additional program information. Displays the available TV channels and guest s Parental Control menu. Shows program details: Title, Broadcast Time, Signal Format, Signal Strength CC, V-Chip, Language, Sound Format, Time, Date, Channel Icon, Channel Label. INSTLLER MENUS Installer Menus 58 Makes adjustments to the TV s operational features. RS-C Control RS-C Control 70 Control TV through TV/STB. PGE 7

18 UDIO IN UDIO OUT RS-C REMOTE IN RJP INTERFCE UX DIGITL DIGITL DIGITL UDIO DISPLY CONTROL VIDEO IN VIDEO OUT OUT (OPTICL) CONTROL C OUT MX 8 960W C IN C 0V~ 60Hz Pillow Speaker Setup Here shown may be somewhat different from your TV. Connect the PILLOW JCK IN the Pillow Speaker output jack on the back of the TV. Connect an accessory pillow speaker or wired remote control unit to this 6-pin jack. Select PILLOW SPEKER on the rear panel of the TV. PILLOW INT PILLOW JCK IN (V DC 0m) REMOTE IN UX CONTROL *Note: If the pillow Speaker switch is set to Pillow Speaker, no sound will be heard from the TV speakers. If pillow speaker switch is set to the Pillow Speaker position, uto Volume will be grayed out and not accessible on the Sound menu. Use a pillow speaker by Curbell, Model or other UL recognized pendant control bearing the warning: Risk of fire if used in oxygen enriched atmosphere. Keep pendant control away from oxygen equipment. Pillow speaker not included with TV. Controlling the TV with Serial Data The TV is capable of being controlled by a single-wire, serial data signal. This is a LG patented technology and is being implemented by certain brands of smart pillow speakers, such as Curbell s GEN-II models. Pillow Speaker Interface This connector furnishes three control lines and an audio output. patient-pendant remote control, or entertainment audio and nurse call system may be connected here. ll lines are isolated from the C power line and earth ground. (Optoisolators isolate the control lines, and a transformer isolates the audio. There are no relays or inductive components in the control lines.) Pin No. Purpose External TV On/Off switch. (Not used.) External Channel Up switch or Data in. Common connection for control, data, and audio output. Impedance to earth ground is a 0-meg resistor in parallel with a 00 pf capacitor. 5 Isolated audio output. Nominal -ohm source impedance with short circuit protection. Intended for a pillow speaker with a low-impedance pad-type volume control. 6 External Channel Down switch. Controlling the TV with Mechanical Switches Pin (common) is momentarily connected to pin,, or 6 via push-action switches to control On/Off and Channel Up/Down. These pins are at + volts DC (when measured from pin ) with the switches open. Current draw is 8 m when a switch is closed. (This operation is identical to previous LG models using the 5- Wire Interface except that only +7 volts DC was supplied and current draw was only.5 m.) PGE 8

19 6 Other Menus & On-Screen Displays Use the remote keys indicated below to access these menus and displays. In this manual, the OSD (On Screen Displays shown) may be different than those on the actual TV. The following are generic examples to familiarize you with the TVs options. 9 9 TIMER Off F SP English G Volume Display Press VOLUME. Shows currently selected sound setting. Sleep Timer Menu Press TIMER. Sets a time to automatically turn the TV off and shows remaining time before TV shutoff. SP Display Selects MTS sound: Mono, Stereo, and SP in analog mode. Change the audio language in DTV mode. larm Timer Current Time :7 M Hr. Min. Move Off djust OK Exit F CPTION Service G Caption Display Press CC. Turns selected option on or off. See Closed Captions page to select options. larm Display Press LRM. Set a time for the TV to turn itself on. Guide Display Press GUIDE to view DTV program information. Press Info for more program information. Channel Preview Press CH PREVIEW. Displays available TV channels. V-Chip Press CC. Move to the V-Chip menu. INFO Press INFO. Check the current program information. PGE 9

20 User Remote Control Key Functions list of the keys and their functions on the optional user remote control, not supplied with the HD Integrator Box System. MUTE Turns sound Off and On, while the picture remains. BNK Press and repeat to select a Channel Memory Bank - -,,, or (Standby). SP Selects MTS sound: Mono, Stereo, and SP in analog mode. Change the audio language in DTV mode. CHNNEL PREVIEW Displays available TV channels, and (if active) the Guest Parental Control menu: set V-Chip blocks to restrict both analog and digital programming. ux Channel allows the guest to select the udio / Video inputs. (Use the /V jacks on the back of the TV as a source). INFO Press to display current program information. [-] BUTTON When selecting a digital broadcast channel, key in the Main channel number followed by the-> [-] -> then the sub channel number. nalog channels do not contain a sub channel number. POWER Turns TV On or Off. GUIDE Use to view DTV program information. CC(Closed Captioning) Press to access closed captions. VOLUME / CHNNEL / OK (Enter) Increase or decrease sound level. Select available channels. Select on-screen menu items and change menu values. NUMBER BUTTONS Use for direct channel entry. FLSHBK (Flashback) Use to return to the last channel viewed. LRM Use to go to the larm menu. Set a time for the TV to turn itself on. TIMER Press repeatedly to select a preset time to automatically shut the TV off. BED /BED (*See Note Below) Determines the code set transmitted, Bed or Bed. Switch setting must correspond to item 7, HOSPITL MODE setting in the TV s Installer Menu. Optional Patient Remote Control *Note: Bed - Bed switch on patient remote. The position of the Bed - Bed switch must correspond to the setting in the Installer s menu. The switch above can be set by sliding it to the Bed or Bed position. On the patient s remote, the Bed or Bed position can be selected by using a paper clip or a ball-point pen to slide the switch to the correct position. Left position = Bed. Right Position = Bed. PGE 0

21 Installer Remote Control Key Functions brief list of the keys on the optional installer s remote and what they do. MUTE Turns sound Off and On, while the picture remains. BNK Press and repeat to select a Channel Memory Bank - -,,, or (Standby). SP Selects MTS sound: Mono, Stereo, and SP in analog mode. Change the audio language in DTV mode. CHNNEL PREVIEW Displays available TV channels, and (if active) the Guest Parental Control menu: set V-Chip blocks to restrict both analog and digital programming. ux Channel allows the guest to select the udio / Video inputs. (Use the /V jacks on the back of the TV as a source). INFO Press to display current program information. [-] BUTTON When selecting a digital broadcast channel, key in the Main channel number followed by the-> [-] -> then the sub channel number. nalog channels do not contain a sub channel number. TIMER Press repeatedly to select a preset time to automatically shut the TV off. POWER Turns TV On or Off. GUIDE Use to view DTV program information. CC(Closed Captioning) Press to access closed captions. VOLUME / CHNNEL / OK (Enter) Increase or decrease sound level. Select available channels. Select on-screen menu items and change menu values. NUMBER BUTTONS Use for direct channel entry. FLSHBK (Flashback) Use to return to the last channel viewed. LRM Use to go to the larm menu. Set a time for the TV to turn itself on. DJ D E F G User DJ (adjust) Up/Down menu arrows, Left/Right to change the selected option. BED /BED (*See Note Below) Determines the code set transmitted, Bed or Bed. Switch setting must correspond to item 7, HOSPITL MODE setting in the TV s Installer Menu. *Note: Bed - Bed switch on patient remote. The position of the Bed - Bed switch must correspond to the setting in the Installer s menu. The switch above can be set by sliding it to the Bed or Bed position. On the patient s remote, the Bed or Bed position can be selected by using a paper clip or a ball-point pen to slide the switch to the correct position. Left position = Bed. Right Position = Bed. PGE

22 uto Program (Channel Search) Use uto Program to automatically find and store all of the channels available in the selected Tuning Band. *Notes: Tuning Band must be set before doing the channel search. See Installer menu item 00 Band/FC. Default setting is, for CTV. When uto Program is run, any assigned channel labels are automatically cleared. With the optional Installer remote control in hand and press the POWER button to turn the TV on. Press the MENU button and then use the DJ D or E button to highlight the Channel menu and press the OK (Enter) button. ntenna uto Program Channel Label Channel List Fine Tune uto Signal Strength G Press the OK (Enter) button to highlight uto program. --: DE Move OK Select MENU Back 5 Press the OK (Enter) button to start the channel search. fter finding all available channels, a display appears briefly showing the number of analog and digital channels found. When finished, press MENU repeatedly to remove the menus. ntenna uto Program Channel Label Channel List Fine Tune Signal Strength Press OK to Search Yes uto Program finds channels being received by the TV s analog and digital tuners. --: F G Move OK Select MENU Back Cable will not work unless you subscribe to a cable service. ntenna uto Program Channel Label Channel List Fine Tune Signal Strength --: MENU Back PGE

23 Channel List fter the channel search, remove unwanted channels. Press the MENU button and then use the DJ D or E button to highlight the Channel menu and press the OK (Enter) button. ntenna uto Program Channel Label Use the DJ D or E button to highlight Channel List and press the OK (Enter) button. --:-- -- Channel List Fine Tune uto Signal Strength G Use the DJ D or E button to highlight the channel you wish to delete and press the DJ G button. The DJ G button toggles the check mark on and off. If the check mark appears next to the channel number, the channel appears in the channel scan DE Move OK Select MENU Back ntenna uto Program Channel Label When finished, press MENU repeatedly to remove the menus. Channel List Fine Tune Signal Strength --:-- -- If you delete a found channel, it isn t gone forever. Simply re-enter the Channel List menu and re-add the channel to show the check mark DE Move G dd/del OK View MENU Back dding ctive Channels (Before -5-5+Menu) Key in active channel number. Go to the Channel List. Click on the right arrow to add the checkmark next to the channel number. Press MENU to exit all menus. When -5-5+Menu is run, the channel number will be added to the channel scan. *Note: For broadcast channel numbers, key in the Physical channel number and add it to the channel list. PGE

24 Channel Control (Continued) Channel Labels Setup - Channel Labels help the user identify the channel or network being viewed. In the Setup menu with the Channel Labels option highlighted, use the DJ D E F G buttons to scroll through the available channel labels, such as, &E, MC, ESPN, HBO, etc. These are a series of preset labels from which you can choose the more common networks. Use any of these to label the channels in the TV s memory. Press the MENU button and then use the DJ D or E button to highlight the Channel menu and press the OK (Enter) button. Use the DJ D or E button to highlight Channel Label and press the OK (Enter) button. This action displays the Channel Label menu. --:-- -- ntenna uto Program Channel Label Channel List Fine Tune uto Signal Strength G Use Channel D or E (+ / -) button to select channels and the DJ D E F G buttons to navigate the labels menu DE Move OK Select MENU Back When the label is highlighted you want for the channel shown in the screen and press OK (Enter) button to add the label to the channel. 5 Select the next channel to label with Channel D or E (+ / -) button to or if finished channel labeling. 6 When finished, press MENU repeatedly to remove the menus. Previous Move CH Change Ch. dd/delete PGE

25 Channel Control Unstable Screen - If a dashed line or no color appears, the screen is unstable, therefore try channel adjustments. (This is only available for analog broadcasting.) Press the MENU button and then use the DJ D or E button to highlight the Channel menu and press the OK (Enter) button. Use the DJ D or E button to highlight Fine Tune and press the OK (Enter) button. --: ntenna uto Program Channel Label Channel List Fine Tune uto G Signal Strength DE Move OK Select MENU Back Press the DJ F or G button to adjust. When finished, press MENU repeatedly to remove the menus. ntenna uto Program Channel Label Channel List Fine Tune Signal Strength --: F G djust MENU Back Checking the Strength of the Digital Signal - This shows the current digital signal strength as a picture. (This is only available for digital broadcasting.) ntenna uto Program Channel Label Press the MENU button and then use the DJ D or E button to highlight the Channel menu and press the OK (Enter) button. --:-- -- Channel List Fine Tune Signal Strength G Use the DJ D or E button to highlight Signal Strength and press the OK (Enter) button DE Move OK Select MENU Back View the on-screen signal strength monitor to see the quality of the signal being received. ntenna uto Program Channel Label Channel List When finished, press MENU repeatedly to remove the menus. Fine Tune Signal Strength --: MENU Back PGE 5

26 Clock Setup (Continued) Manual Time Settings -Use the DJ D E F G buttons to set the year, month, day, hours and minutes. 5 6 Press the MENU button and then use the DJ D or E button to highlight the Setup menu and press the OK (Enter) button. Use the DJ D or E button to highlight Time. Press the OK (Enter) button to highlight Clock. Manual or uto will appear on the menu next to clock. If manual is selected, on the menu use the DJ D or E button to highlight Manual and press the OK (Enter) button. Use the DJ D or E button to highlight Manual Clock and press the OK (Enter)button. Use the DJ DEF Gbuttons to set the year, month, day, M/PM, hours and minutes. When finished, press MENU repeatedly to remove the menus. On-Off Timers Setup Set the On-Off Timers using the procedures described above. --: : : Time G V-Chip Menu Language English Menu Transparency Semi Opaque Set ID DEMove OK Select MENU Back Clock Manual G Manual Clock Daylight Saving Time Zone On Timer Off Timer uto Off Off DEMove OK Select MENU Back Clock Manual Clock Daylight Saving uto Time Zone Manual On Timer Off Timer uto Off DESelect MENU Back *Notes: If you intend to use the On-Off Timers, it is best to set the clock manually. Clock Manual Clock Daylight Saving Manual G Time Zone On Timer Off Timer --:-- -- uto Off Off DEMove OK Select MENU Back Clock Manual Clock Daylight Saving Time Zone On Timer Off Timer --:-- -- uto Off DEdjust F G Move MENU Back PGE 6

27 Clock Setup (Continued) utomatic Time Settings - If you select auto time setting, time will be set from the digital broadcast information. Press the MENU button and then use the DJ D or E button to highlight the Setup menu and press the OK (Enter) button. Use the DJ D or E button to highlight Time. Press the OK (Enter) button to highlight Clock. Manual or uto will appear on the menu next to clock. Select uto on the sub-menu with the DJ D or E button and press the OK (Enter) button. Use the DJ DEF Gbuttons to set the Daylight Savings and Time Zone options for your local area. See the next page. --: : Time G V-Chip Menu Language English Menu Transparency Semi Opaque Set ID DEMove OK Select MENU Back Clock Manual G Manual Clock Daylight Saving Time Zone On Timer Off Timer uto Off Off DEMove OK Select MENU Back 5 When finished, press MENU repeatedly to remove the menus. Caution: Some digital channels may change the time incorrectly using the utomatic Clock Set feature. In this event, the larm may not function as intended and the TV may not turn on at the expected time. If the end user will have access to the larm, it may be best to use the Manual Clock Set mode and set the clock to local time manually. --: Clock Manual Clock Daylight Saving Time Zone uto On Timer Manual Off Timer uto Off DESelect MENU Back Mini glossary TIME HOURS MINUTES four-digit figure broken down into hours and minutes, used to enter the current time when setting the clock or wake-up alarm. First two digits that are entered when setting the clock or the wake-up alarm. The last two digits that are entered when setting the clock, or the wake-up alarm. PGE 7

28 Clock Setup (Continued) Daylight Saving -Installer can select to use Daylight Savings to adjust the clock time. This is operated from the utomatic Time Settings. Time G V-Chip Menu Language English Press the MENU button and then use the DJ D or E button to highlight the Setup menu and press the OK (Enter) button. Menu Transparency Semi Opaque Set ID Use the DJ D or E button to highlight Time. DEMove OK Select MENU Back Press the OK (Enter) button to highlight Clock. Use the DJ D or E button to highlight the Daylight Saving and press the OK (Enter) button. Setup Clock Manual Clock Daylight Saving Time Zone On Timer No Yes 5 Use the DJ D or E button to choose Yes or No. Off Timer uto Off 6 When finished, press MENU repeatedly to remove the menus. DESelect MENU Back Time Zone Settings -Installer can set the Time Zone. This is operated from the utomatic Time Settings. Time G V-Chip Press the MENU button and then use the DJ D or E button to highlight the Setup menu and press the OK (Enter) button. Menu Language English Menu Transparency Semi Opaque Set ID Use the DJ D or E button to highlight Time. DEMove OK Select MENU Back Press the OK (Enter) button to highlight Clock. Use the DJ D or E button to highlight Time Zone and press the OK (Enter) button. Clock Manual Clock Daylight Saving Time Zone Easten 5 Use the DJ F or G button to select the Time Zone and press the OK (Enter) button. On Timer Off Timer uto Off 6 When finished, press MENU repeatedly to remove the menus. F G Select MENU Back PGE 8

29 Clock Setup (Continued) TV ctivation Time Settings -You can set a time for the TV to automatically turn-on. Time G V-Chip Menu Language English Press the MENU button and then use the DJ D or E button to highlight the Setup menu and press the OK (Enter) button. Menu Transparency Semi Opaque Set ID Use the DJ D or E button to highlight Time. DEMove OK Select MENU Back Press the OK (Enter) button to highlight Clock. Use the DJ D or E button to highlight On Timer and press the OK (Enter) button. Clock Manual Clock Daylight Saving Time Zone On Timer 5 6 Use the DJ DEF Gbuttons to choose M / PM, Hours, Minutes and time period to turn-on. When finished, press MENU repeatedly to remove the menus. Off Timer uto Off DEdjust F G Move MENU Back TV Deactivation Time Settings -You can set a time for the TV to automatically turn-off. Time V-Chip G Menu Language English Press the MENU button and then use the DJ D or E button to highlight the Setup menu and press the OK (Enter) button. Menu Transparency Semi Opaque Set ID Use the DJ D or E button to highlight Time. DEMove OK Select MENU Back Press the OK (Enter) button to highlight Clock. Clock Use the DJ D or E button to highlight Off Timer and press the OK (Enter) button. Manual Clock Daylight Saving Time Zone On Timer 5 6 Use the DJ DEF Gbuttons to choose M / PM, Hours, Minutes and time period to turn-off. When finished, press MENU repeatedly to remove the menus. Off Timer uto Off DEdjust F G Move MENU Back PGE 9

30 Clock Setup uto Off - If there is no signal on the TV for 5 minutes or more, or if no button is pressed for more than hours, this function turns off the TV automatically. 5 6 Press the MENU button and then use the DJ D or E button to highlight the Setup menu and press the OK (Enter) button. Use the DJ D or E button to highlight Time. Press the OK (Enter) button to highlight Clock. Use the DJ D or E button to highlight uto Off and press the OK (Enter) button. Use the DJ D or E button to choose On or Off. When finished, press MENU repeatedly to clear the menus. Time G V-Chip Menu Language English Menu Transparency Semi Opaque Set ID DEMove OK Select MENU Back Clock Manual Clock Daylight Saving Off Time Zone On On Timer Off Timer uto Off DESelect MENU Back PGE 0

31 V-Chip (Continued) Entering a PIN (Password) - This option sets up or changes the password for blocking program ratings. Time V-Chip G Menu Language English Press the MENU button and then use the DJ D or E button to highlight the Setup menu and press the OK (Enter) button. Menu Transparency Semi Opaque Set ID Use the DJ D or E button to highlight V-Chip and press the OK (Enter) button. DE Move OK Select Menu Back 5 Use the DJ D or E button to highlight On/Off and press the OK (Enter) button. Use the DJ D or E button to highlight On and press the OK (Enter) button. If a password has been entered, key it in using the number keypad. If no password has been set, enter the digits password (0-9) using the remote control. This is the PIN. Each time the menu is entered, the password will be required until the block time expires. The TV is set up with the default password On/Off Changing PIN Set Block Hour TVPG Rating MP Rating Can. English Rating Can. French Rating D/L Rating DE Select Menu Back On/Off On Changing PIN Set Block Hour TVPG Rating Off On G MP Rating 6 7 Use the DJ D or E button to highlight Changing PIN and press the OK (Enter) button. Enter the digits password. s soon as the digits are entered, re-enter the same digits on the Confirm PIN. Can. English Rating Can. French Rating D/L Rating DE Move OK Select Menu Back On/Off Changing PIN 8 When finished, press MENU repeatedly to remove the menus. Set Block Hour TVPG Rating MP Rating If you ever forget your password, key in 7, 7, 7, 7 on the remote control. Can. English Rating Can. French Rating D/L Rating 0 ~ 9 Number Menu Back PGE

32 V-Chip (Continued) Set Block Hour. - This option sets up hour that you wish to block. Time V-Chip G Menu Language English Press the MENU button and then use the DJ D or E button to highlight the Setup menu and press the OK (Enter) button. Menu Transparency Semi Opaque Set ID Use the DJ D or E button to highlight V-Chip and press the OK (Enter) button. DE Move OK Select Menu Back Enter the digits password. Use the DJ D or E button to highlight Set Block Hour and press the OK (Enter) button. On/Off On Changing PIN Set Block Hour G TVPG Rating MP Rating Can. English Rating 5 Use the DJ D or E button to choose ~ hours and press the OK (Enter) button. Can. French Rating D/L Rating DE Move OK Select Menu Back 6 When finished, press MENU repeatedly to remove the menus. On/Off Changing PIN Set Block Hour TVPG Rating MP Rating Can. English Rating Can. French Rating D/L Rating DE Select Menu Back PGE